Search Results

Search found 13104 results on 525 pages for 'malcolm box'.

Page 415/525 | < Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• ubuntu 9.04 pptp broken after a power failure

  - by kevin42

  I have a small Ubuntu 9.04 router setup as a NAT box and a PPTP server. After a power failure everything except the PPTP server still works. A windows client gets to "registering your computer on the network" but then says Error 742: The remote computer does not support the required data encryption type. I did some research and I think the problem is with the ppp_mppe module. When I try to run 'modprobe ppp_mppe' it hangs indefinitely. What would cause this hang? Any ideas how I can troubleshoot this further? Thanks for the help! UPDATE: I am still having the problem, however I have found some more information. When the first user tries to connect to pptp, the process list shows modprobe sha1 running, and one instance of modprobe ppp_mppe for each connection attempt. If I killall modprobe at this point the next connection attempt works, and everything is fine until the next reboot. I'm planning to do a clean install at some point in the future but I'd really like to get to the real cause of this.

  Read the article

• Use a preferred username but authenticate against Kerberos principal

  - by Jason R. Coombs

  What I desire to do should be pretty simple. I have an Ubuntu 10.04 box. It's currently configured to authenticate users against a kerberos realm (EXAMPLE.ORG). There is only one realm in the krb5.conf file and it is the default realm. [libdefaults] default_realm = EXAMPLE.ORG PAM is configured to use the pam_krb5 module, so if a user account is created on the local machine, and that username matches the [email protected] credential, that user may log in by supplying his kerberos password. What I would like to do instead is create a local user account with a different username, but have it always authenticate against the canonical name in the kerberos server. For example, the kerberos principal is [email protected]. I would like to create the local account preferred.name and somehow configure kerberos that when someone attempts to log in as preferred.name, it uses the principal [email protected]. I have tried using the auth_to_local_names in krb5.conf, but this doesn't seem to do the trick. [realms] EXAMPLE.ORG = { auth_to_local_names = { full.name = preferred.name } I have tried adding [email protected] to ~preferred.name/.k5login. In all cases, when I attempt to log in as preferred.name@host and enter the password for full.name, I get Access denied. I even tried using auth_to_local in krb5.conf, but I couldn't get the syntax right. Is it possible to have a (distinct) local username that for all purposes behaves exactly like a matching username does? If so, how is this done?

  Read the article

• Cannot delete flash9.ocx

  - by Kara Marfia

  Some kinda voodoo, indeed. Bought a new boot drive, and it's time to use the old drive for data. I thought I'd save some time by just wiping the unneeded system folders, instead of backing up, formatting, and restoring. Wups! I have a single Adobe file that absolutely will not be deleted. G:\Windows\SysWOW64\Macromed\Flash\flash9.ocx - though it may have started with a different file name. I'm able to rename it, oddly enough. To be clear, the drive is currently plugged in externally. So I can boot the computer, plug this drive in afterward, and immediately attempt to delete. "File in use" box reads "the action can't be completed because the file is open in another program". I'd format at this point, but it's my white whale, and I have to know if Adobe has inserted some nasty little registry hack - or whatever it is - making this impossible. Since I'm sure it'll come up, I've taken ownership of the file - and this was the trick preventing me from deleting anything else on the drive - full rights on the file permissions, you name it, I've fiddled with the file itself. I'm about to try uninstalling flash from the system drive, in case that aligns the planets properly. Sometimes I wish I were less stubborn, and could just format already.

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by nfm

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• Why dd finishes instantly when pipelining to cat?

  - by agsamek

  I start bash on Cygwin and type: dd if=/dev/zero | cat /dev/null It finishes instantly. When I type: dd if=/dev/zero > /dev/null it runs as expected and I can issue killall -USR1 dd to see the progress. Why does the former invocation finishes instantly? Is it the same on a Linux box? * Explanation why I asked such stupid question and possibly not so stupid question I was compressing hdd images and some were compressed incorrectly. I ended up with the following script showing the problem: while sleep 1 ; do killall -v -USR1 dd ; done & dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c Wc should write 1000000000 at the end. The problem is that it does not on my machine: bash-3.2$ dd if=/dev/zero bs=5000000 count=200 | gzip -c | gzip -cd | wc -c 13+0 records in 12+0 records out 60000000 bytes (60 MB) copied, 0.834 s, 71.9 MB/s 27+0 records in 26+0 records out 130000000 bytes (130 MB) copied, 1.822 s, 71.4 MB/s 200+0 records in 200+0 records out 1000000000 bytes (1.0 GB) copied, 13.231 s, 75.6 MB/s 1005856128 Is it a bug or am I doing something wrong once again?

  Read the article

• HP Laserjet 1320 drivers for Windows 7

  - by RedGrittyBrick

  Background I replaced som XP computers with Win 7 computers. We have a HP Laserjet 1320dn printer attached to the LAN. The XP computers could print to it from Word in duplex mode without any issues. Problem The Win 7 computers downloaded a full set of drivers including a "HP Laserjet 1320 PCL5" driver. However using this, Word's page footers cause extra pages to be printed with just a letter or so at a time from the footer. Some other apps have similar issues. I also have an ancient Laserjet 1200 attached to the LAN via a Jetdirect box and that works just fine. So I don't think the problem is with Word (the computers came with Word 2010 starter). What I tried I wrangled the control-panel new printer dialogue into using a "HP Laserjet 2100 PS" driver for the HP Laserjet 1320dn. Now my Word documents print as they should. However I don't have a duplex option on the print dialogue. I'd really like to be able to use duplex printing. Question Windows used to have a Universal Postscript driver that read a Postscript Printer Definition (PPD) file to make the printer's features available (tray choice, duplex etc). I can't see any way to do this in Windows 7. Is there a way? Is there any other way I can get Windows 7 Home Premium 64-bit to print properly to a HP Laserjet 1320dn and have access to all it's major features? Addendum: My page in Word looks like this: +--------------------+ | aa bb cc | | | | lorem ipsum dolor | | | ... | | | pp qq rr | +--------------------+ The headers and footers were inserted using Insert - header - blank (3 column). When printed I get 1 page with aa, bb, cc, pp in correct position (no other text) 1 blank page 1 page with qq in correct position (no other text) 1 blank page 1 page with rr in correct position (no other text) 1 blank page 1 page with lorem ipsum dolor in correct position (no headers or footers) If I use a Laserjet 2100 driver I get 1 correct page.

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• how to setup a bridge with 2 NICs and few virtual machines

  - by Bond

  Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

  Read the article

• Windows 2003 DC to Windows 2008 R2 DC with same name and same IP

  - by TheCleaner

  Environment = Windows 2003 native domain with 8 DCs I've got an old domain controller that is running 2003, CA Enterprise role, DHCP, DNS, a few GPO scripts that point to shares on it, and some other minor functions. All our servers point to it as their primary DNS, and there's lots of references to its IP or name throughout the domain at this point (8+ years later). I really don't feel like manually changing all of this, it would be a pretty massive undertaking. I want to follow this guide: http://msmvps.com/blogs/acefekay/archive/2010/10/09/remove-an-old-dc-and-introduce-a-new-dc-with-the-same-name-and-ip-address.aspx to hopefully end up with basically an "in-place upgrade" so to say. I considered just doing a P2V of the box, but we don't really want to keep it around running 2003 to be honest. I also considered using a CNAME and adding a 2nd IP (the old one) but again, it seemed like it would be cleaner using the attached link. My actual question: Any gotchas or big caution signs when doing what the link suggests? Anyone gone down this road and have advice on how to proceed?

  Read the article

• Setup my domain at Whois.com as nameservers for a Dedicated Server with Kloxo

  - by BoDiE2003

  Hello, this is my first time at ServerFault, I'm a stackoverflow user. I'm faceing the next problem and may be its me, but I can't find proper guides to set up a domain and nameservers for a dedicated box. I have a domain, at whois.com, and a Dedicated server at Reliable Hosting Services, the server has 5 IPs, I know that I need 2 of them for the nameservers. Right now, my domain at whois.com is using nsX.whois.com nameservers and it has 2 child nameservers: ns1.mydomain.com & ns2.mydomain.com pointing to those 2 IPs from my Server. Whats next? I still cannot set that domain as my main server domain since it says: To map an IP to a domain, the domain must ping to the same IP, otherwise, the domain will stop working. The domain you are trying to map this IP to, doesn't resolve back to the IP, and so it cannot be set as the default domain for the IP. Well and I'm stuck on those steps, whats next to have my nameservers working and my main domain assigned to my server? Thank you very much and happy new year!!

  Read the article

• Varnish with multiple sites/boxes

  - by jerhinesmith

  Is it possible for Varnish to redirect traffic to different IPs based on the url? For example, is the following setup feasible (and if so, what would the VCL look like): *.example.com points to Varnish IP address When a request is made to foo.example.com, varnish checks the cache and sends the request to Server1's IP address on a cache miss. When a request is made to bar.example.com, varnish checks the cache and sends the request to Server2's IP address on a cache miss. foo and bar are (for the most part) completely unrelated sites. They use the engine, but have different content and their own distinct database. Since there previously was no penalty for doing so (other than cost) we split them up into two separate boxes so that a ton of traffic to foo won't have a negative impact on visitors browsing around bar. I could set up two instances of varnish and have one serve up foo's static content and the other serve up bar's, but as there doesn't seem to be much overhead to running Varnish, I think (perhaps mistakenly) that it would make more sense to go with one Varnish server that redirects the traffic to the appropriate box on a cache miss.

  Read the article

• How to avoid sshfs freezing?

  - by Andreas Hagen

  So the issue is this: I've installed sshfs on Ubuntu 12.04 and I'm trying to connect to a couple of remote servers. So initially the mount seams successful. Sometimes Gnome even picks it up and displays the "new device found" box at the bottom of the screen. but from here on there is not much that works. Or at least not any more. The first couple of times i connected it seamed to work fine, and I was able to transfer some files, then i disconnected using fusermount -u <folder> and after reconnecting a little later the trouble started. Now after executing sshfs -o ServerAliveInterval=15 -o reconnect -C -o workaround=all -o idmap=user root@<host>:/ <folder>, when I change directory into the mount-point, the shell just freezes. Strangely ls -al <folder> works when listing just the root of the remote system, but nothing more. Also every file-explorer I've tried freezes just like cd <folder>. To me it seamed like there was some kind of zombie thread or something hanging around my system, due to the fact that it did work the first time, so I have tried rebooting but no luck. sshfs -V gives this: SSHFS version 2.3 FUSE library version: 2.8.6 fusermount version: 2.8.6 using FUSE kernel interface version 7.12 So yea, any ideas?

  Read the article

• SQL Server performance on VSphere 4.0

  - by Charles

  We are having a performance issue that we cannot explain with our VMWare environment and I am hoping someone here may be able to help. We have a web application that uses a databases backend. We have an SQL 2005 Cluster setup on Windows 2003 R2 between a physical node and a virtual node. Both physical servers are identical 2950's with 2x Xeaon x5460 Quad Core CPUs and 64GB of memory, 16GB allocated to the OS. We are utilizing an iSCSI San for all cluster disks. The problem is this, when utilizing the application under a repeated stress testing that adds CPUs to the cluster nodes, the Physical node scales from 1 pCPU to 8 pCPUs, meaning we see continued performance increases. When testing the node running Vsphere, we have the expected 12% performance hit for being virtual but we still scale from 1 vCPU to 4 vCPUs like the physical but beyond this performance drops off, by the time we get to 8 vCPUs we are seeing performance numbers worse than at 4 vCPUs. Again, both nodes are configured identically in terms of hardware, Guest OS, SQL Configurations etc and there is no traffic other than the testing on the system. There are no other VMs on the virtual server so there should be no competition for resources. We have contacted VMWare for help but they have not really been any suggesting things like setting SQL Processor Affinity which, while being helpful would have the same net effect on each box and should not change our results in the least. We have looked at all of VMWare's SQL Tuning guides with regards to VSphere with no benefit, please help!

  Read the article

• Windows 7 Automatically Connecting To Unsecured Wireless Networks On Startup

  - by Xtend

  Most of the questions on this topic related to folks connecting to somebody else's wireless network when their own was available and could remedy the situation by going to their connections and unchecking the "connect automatically" box. See this: " Avoid automatically connecting to wireless network on windows 7 " as an example. In my situation, I've noticed that Win 7 will automatically connect to any unsecured wifi network - even if I have never connected to it in the past. If I am traveling and boot Win 7, it will start and connect to what appears to be the best signaled unsecured network without prompting me for confirmation (note: in the above link, "Naveen" seems to have same problem). Obviously, that is a security concern to me. Further, when I open "Network and Sharing" and "Manage wireless networks" the network is not displayed (probably because I labelled it a public network). Again, these are new, never connected with before, wireless networks. I always promptly disconnect from them but don't want to have to be on constant guard for an auto connection to a malicious network. This began about a month ago, as I recall, Win 7 did not behave like this in the past, I didn't monkey with wifi settings, and don't use a 3rd party connection manager. I did have to download some internet security certificates for army website access but I don't think that should mess with network settings. Any ideas how I can tell Win7 cease automatically connecting to networks or, at least, to prompt me for a confirmation before connecting?

  Read the article

• Wake on Demand for Apache server in OS X 10.8

  - by Gary

  Mac OS X Mountain Lion does not have a Web Sharing box in the Sharing system prefs menu. It is thoroughly discussed on the web that the Apache server is available, and that it can be turned on manually in the command line, or by using a convenient Prefs Pane. That works while the computer is awake. But, when my computer goes to sleep, the server stops working, even though Wake for Network Access is checked in the Energy Saver Pref Pane. From the discussion on Bonjour, I see that this problem probably results from the fact that Apache isn't registered with Bonjour. Does that sound likely? If not, please make some suggestions. The connection is via hard-wired ethernet. If registration with Bonjour is the problem, I'd like to know how to register it. You gave a nice description of dns-sd, and the command description says dns-sd -R Name Type Domain Port [TXT...] (Register a service)", but I don't know what to use for "Name" or "Type", or the format of the domain. I tried some dns-sd -B searches and found nothing I could use as a model, and it doesn't show up in Bonjour Browser. Any suggestions would be appreciated.

  Read the article

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Interesting phenomenom with Windows Server 2008 R2 user access controls and NTFS ACLs

  - by Simon Catlin

  One to try, and I'd appreciate any thoughts on this. On a Windows Server 2008 R2 box (or presumably 2008 R1, Windows Vista or Windows 7): i) Logon as an administrator, and create a new NTFS volume ii) Blow away the standard MS ACLS on the root of the volume (which are laughable), and replace with Administrators:Full Control, System:Full Control, e.g.: echo Y|cacls.exe d:\ /g "Administrators:F" "SYSTEM:F" iii) Now, from a Command Prompt shell window or PowerShell window, switch to that drive (cd /d D:\ or set-location D:\ ). Works fine... no issues. iv) Now, try to browse to the root of the new volume using MS Explorer... Access denied. Now, I've kind of convinced myself that it is UAC getting in the way, as you can add "Authenticated Users:List" access to D:\ and Explorer then works. I can only assume that MS Explorer isn't able to use the "admin" token for the Administrator. Browsing to explorer.exe and doing a "Run as administrator" has no effect. Any thoughts? Cheers in advance.

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• Windows Media Center showing Jerky Video on PC

  - by Kris Erickson

  I had to repave my Windows 7 x64 box last week due to a hard drive crash, and for a while everything was running perfectly but now all videos in Windows Media Center are jerky (the sound is fine, they just seem to skip a ton of frames all the time). This is on the local machine, but the same thing happens when I try to stream to my Xbox. The videos all show fine in VLC and Windows Media Player (however exhibit the same problem in Quicktime). I guess I must have installed something recently (in the process of getting all the apps I usually have running on my PC) that caused this but for the life of me I can't figure it out. I have updated to the latest video driver (and then rolled back to the standard Windows 7 driver), I have rolled back all the other drivers that I have installed (I believe). I have uninstalled all the codec packs (I also run TVersity, so I have the TVersity codec pack installed), and I uninstalled TVersity. Nothing seems to help. I have uninstalled windows media center, and reinstalled it from the Programs and Features. I have basically ran out of things to try to fix this, and am almost thinking about reinstalling Windows again. Any suggestions? Edit Specs on the PC (which I figured was unimportant since everything used to work perfectly): Intel Core 2 CPU 6600 @ 2.4 Ghz Nvidia GTS 8800 Built in realtek-audio soundcard 4GB Ram Codecs which are failing: All that I have tried, but at least Xvid, Mpgv (mpeg2 video from a camera), and Wmv (only kinds that I have ready access to).

  Read the article

• Certificate enrollment request chain not trusted

  - by makerofthings7

  I am working on a MSFT lab for Direct Access, and need to create a Web certificate. The instructions ask be to do the following: On EDGE1, click Start, type mmc, and then press ENTER. Click Yes at the User Account Control prompt. Click File, and then click Add/Remove Snap-ins. Click Certificates, click Add, click Computer account, click Next, select Local computer, click Finish, and then click OK. In the console tree of the Certificates snap-in, open Certificates (Local Computer)\Personal\Certificates. Right-click Certificates, point to All Tasks, and then click Request New Certificate. Click Next twice. On the Request Certificates page, click Web Server, and then click More information is required to enroll for this certificate. On the Subject tab of the Certificate Properties dialog box, in Subject name, for Type, select Common Name. In Value, type edge1.contoso.com, and then click Add. Click OK, click Enroll, and then click Finish. In the details pane of the Certificates snap-in, verify that a new certificate with the name edge1.contoso.com was enrolled with Intended Purposes of Server Authentication. Right-click the certificate, and then click Properties. In Friendly Name, type IP-HTTPS Certificate, and then click OK. Close the console window. If you are prompted to save settings, click No. In production, our company has overridden the Web Server template and it doesn't seem to be issuing certificates with the full CA chain. When I look at the issued certificate properties then both tiers of the 2 tier CA hierarchy are missing. How can I fix this? I'm not sure where to look outside the GUI.

  Read the article

• TCPDump and IPTables DROP by string

  - by Tiffany Walker

  by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

  Read the article

• Not getting IP from ISP on Multicast Network

  - by Johan Nielsen

  Im having an odd issue with my ISP (COMX.dk) I have a managed access gateway box (Telsay) with three 8P8C ports for use with Internet and Ip-Tv (respectively on different VLANS (so does my ISP tell me)) To utilize a port you will need to register your device's mac address through an online interface. You will then get your device paired with a static ip. I am using one port actively and I have registered another device (router). The router is configured to listen for an active dhcpd on the network. When my router get a lease I get a private ip 192.168.2.2 (not the one bound to my mac) which is odd! I unconnected my router from the gateway and connected my laptop directly. Same thing happened - I was given a private address. I did a port scan on the gateway and found port 80 to be open and browsed to the ip. I was then presented with a management interface of a Belkin wireless router (HMMM!!!!) <--by the way, not my gear At this point I called the ISP to let them know of my issue/findings - Only to be replied "Well, we cant see any rogue dhcp servers" (thinking to myself, well I can) I then decided that it could be fun to try the other port of my gateway, only to experience the same. So I reconnected my router and used the remaining port to make an observer(wireshark promic etc.) I am able to see my router trying to discover a dhcp server but I can also see my ISP's IGMP and PIMv2 packages just repeating the same pattern. Hello...Hello...Hello :) So I called them again, only to get the same response, "we dont see any rogue dhcp's...we cant see the host you are talking to (mac address of the Belkin router)...you are definitively connected through wireless?!?(no im not, no such thing as a wireless wire - i thought to myself)" My questions is, What is going on? (besides from what im reporting here) What am I seeing that the don't? What can I tell them in order for them to resolve mine/their issue?

  Read the article

• SQL Server log backups "stalling"

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• setting up tracd behind mod_proxy?

  - by FilmJ

  I'm having trouble setting up mod_proxy and tracd. Seems almost all the search results for this problem take me to the built-in trac documentation page that mentions it as an option. I have several VirtualServers already running on the box in question, so running tracd on port 80 or 443 is not an option, but I do want to make my trac server accessible on this machine without exposing an additional port via the firewall. Making things even more complicated is that I have multiple trac repositories being served by the same instance of tracd, and so I want to set it up so: http://trac.abc.com is proxy'd to localhost:8000/projects/abcproject, and http://trac.def.com is proxy'd to localhost:8000/projects/defproject. Currently, the setup I have below results in 100% 403 errors. The server is running as www-data and the directory where all trac files are stored is owned by www-data, AND tracd (as show below) is running as www-data, so not sure where it's getting hung up. The relevant configuration on /var/apache2/sites-enabled/trac.abc.com: ProxyPass / http://localhost:8000/abcproject ProxyPassReverse / http://localhost:8000/abcproject The relevant configuration on /var/apache2/sites-enabled/trac.def.com: ProxyPass / http://localhost:8000/defproject ProxyPassReverse / http://localhost:8000/defproject The command used to instantiate tracd: tracd -a defproject,/var/www/vhosts/trac-common/users.htdigest,DEFProject -a abcproject,/var/www/vhosts/trac-common/users.htdigest,ABCProject -p 8000 -b localhost -e /var/www/vhosts/trac-common/projects If I access the site at http://localhost:8000/ everything works fine, but if I try to access via any of the proxy'd hosts I end up with 403 at every turn. I've used mod_proxy successfully as described above for other servers, such as couchdb, so maybe this has to do with the headers sent by tracd??

  Read the article

< Previous Page | 411 412 413 414 415 416 417 418 419 420 421 422  | Next Page >