Search Results

Search found 14624 results on 585 pages for 'static'.

Page 416/585 | < Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >

• Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

  - by neezer

  For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

  Read the article

• SQL Server Instance login issue

  - by reallyJim

  I've just brought up a new installation of SQL Server 2008. I installed the default instance as well as one named instance. I'm having a problem connecting to the named instance from anywhere besides the server itself with any user besides 'sa'. I am running in mixed mode. I have a login/user that has a known username. Using that user/login, I can properly connect when directly on the server. When I attempt to login from anywhere else, I recieve a "Login failed for user ''", with Error 18456. In the log file in the server, I see a reason that doesn't seem to help: "Reason: Could not find a login matching the name provided.". However, that user/login DOES exist, as I can use it locally. There are no further details about the error. Where can I start to find something to help me with this? I've tried deleting and recreating the user, as well as just creating a new one from scratch--same result, locally fine, remotely an error. EDIT: Partially Resolved. I'm now passed the base issue--the clients were trying to connect via the default instance. I don't know why. So, once proper ports were opened in the firewall, and a static port assigned to the named instance, I can now connect--BUT ONLY if I specify the connection as Server,Port. SQLBrowser is apparently not helping/working in this case. I've verified it IS running, and done a stop/restart after my config changes, but no difference yet.

  Read the article

• bind9 dlz/mysql at ubuntu segfault libmysqlclient.so

  - by Theos

  I have a big problem. I installed the bind9 nameserver to three different computer. two Ubuntu 10.04.4 LTS, and one Ubuntu 11.10 I compiled it 9.7.0, 9.7.3, 9.9.0 with this method: ./configure --prefix=/usr --sysconfdir=/etc/bind --localstatedir=/var \ --mandir=/usr/share/man --infodir=/usr/share/info \ --enable-threads --enable-largefile --with-libtool --enable-shared --enable-static \ --with-openssl=/usr --with-gssapi=/usr --with-gnu-ld \ --with-dlz-mysql=yes --with-dlz-bdb=no \ --with-dlz-filesystem=yes --with-geoip=/usr make make install After the set up for dlz/mysql, the BIND server is working perfetctly until 5-30 minute long. Ahter i got segfault. I resolve temporaly the problem with a simple process watchdog, and if the named is stopped, the watchdog is restart it, but this is not a good idea in long therm. My log output is: messages: Apr 13 19:33:51 dnsvm kernel: [ 8.088696] eth0: link up Apr 13 19:33:58 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.082572] named[1027]: segfault at 88 ip b71c4291 sp b5adfe30 error 4 in libmysqlclient.so.16.0.0[b714e000+1aa000] Apr 13 19:35:08 WATCHDOG: named not running. Restarting Apr 13 19:35:08 dnsvm kernel: [ 87.457510] named[1423]: segfault at 68 ip b71d6122 sp b52f0a40 error 4 in libmysqlclient.so.16.0.0[b7160000+1aa000] Apr 13 19:35:09 WATCHDOG: named not running. Restarting Apr 13 19:41:56 dnsvm kernel: [ 494.838206] named[1448]: segfault at 88 ip b731c291 sp b5436e30 error 4 in libmysqlclient.so.16.0.0[b72a6000+1aa000] Apr 13 19:41:57 WATCHDOG: named not running. Restarting Apr 13 19:57:26 dnsvm kernel: [ 1424.023409] named[2976]: segfault at 88 ip b72d1291 sp b6beee30 error 4 in libmysqlclient.so.16.0.0[b725b000+1aa000] Apr 13 19:57:26 WATCHDOG: named not running. Restarting Apr 13 20:11:56 dnsvm kernel: [ 2294.324663] named[6441]: segfault at 88 ip b7357291 sp b6473e30 error 4 in libmysqlclient.so.16.0.0[b72e1000+1aa000] Apr 13 20:11:57 WATCHDOG: named not running. Restarting syslog: http://pastebin.com/hjUyt8gN the first server is a native, normal x64 server (u1004lts), the second is virtualised server (u11.10) the third is also virtualised (10.04lts) This servers is only for dns providing with mysql server db. But the problem is be with all server, and all bind version. named.conf: http://pastebin.com/zwm1yP7V Can anybody help me, or any good idea?

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• Debian Linux bridging router intermittently dropping packets [migrated]

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

  Read the article

• netsnmp - how to register string?

  - by user1495181

  I use net-snmp. I try to add my own mibs (no need in handler, just a MIB that i can get and set by snmp call), so i followed the scalar example. In order to add my own mibs i defined them in the mib file and create an agent extension.(see below). It work, so i have now an integer MIB. Now i want to add string mib, so i define the MIB , but i dont find a register API for string, like i have for the int - netsnmp_register_int_instance. I look in the includes file , but dosnt found matching one. agent: #include <net-snmp/net-snmp-config.h> #include <net-snmp/net-snmp-includes.h> #include <net-snmp/agent/net-snmp-agent-includes.h> #include "monitor.h" static int int_init = 0; /* default value */ void init_monitor(void) { oid open_connections_count_oid[] = { 1, 3, 6, 1, 4, 1, 8075, 1, 0 }; netsnmp_register_int_instance("open_connections_count", open_connections_count_oid, OID_LENGTH(open_connections_count_oid), &int_init, NULL); }

  Read the article

• Unable to logon to vpn

  - by nitin pande

  My openvpn client log file- The interesting bit: Tue Oct 26 12:32:49 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:49 2010 TCP/UDP: Closing socket The rest of the log just in case: Tue Oct 26 12:32:35 2010 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Tue Oct 26 12:32:48 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:48 2010 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Oct 26 12:32:48 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 12:32:48 2010 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 12:32:48 2010 LZO compression initialized Tue Oct 26 12:32:48 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:48 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:48 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:48 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:48 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:32:48 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:32:48 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:32:48 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 TLS: Initial packet from 67.228.223.12:3389, sid=bd5f79fe 8475497f Tue Oct 26 12:32:49 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:49 2010 TCP/UDP: Closing socket Tue Oct 26 12:32:49 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:32:49 2010 Restart pause, 5 second(s) Tue Oct 26 12:32:54 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:54 2010 Re-using SSL/TLS context Tue Oct 26 12:32:54 2010 LZO compression initialized Tue Oct 26 12:32:54 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:54 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:54 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:54 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:54 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:32:54 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TLS: Initial packet from 67.228.223.12:3389, sid=1643b931 ce240d5f Tue Oct 26 12:32:54 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:54 2010 TCP/UDP: Closing socket Tue Oct 26 12:32:54 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:32:54 2010 Restart pause, 5 second(s) Tue Oct 26 12:32:59 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:59 2010 Re-using SSL/TLS context Tue Oct 26 12:32:59 2010 LZO compression initialized Tue Oct 26 12:32:59 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:59 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:59 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:59 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:59 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:00 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TLS: Initial packet from 67.228.223.12:3389, sid=cd439fb2 d625ca0d Tue Oct 26 12:33:00 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:00 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:00 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:00 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:05 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:05 2010 Re-using SSL/TLS context Tue Oct 26 12:33:05 2010 LZO compression initialized Tue Oct 26 12:33:05 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:05 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:05 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:05 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:05 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:06 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TLS: Initial packet from 67.228.223.12:3389, sid=28f0cb87 69c90cde Tue Oct 26 12:33:06 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:06 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:06 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:06 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:11 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:11 2010 Re-using SSL/TLS context Tue Oct 26 12:33:11 2010 LZO compression initialized Tue Oct 26 12:33:11 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:11 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:11 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:11 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:11 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:11 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:11 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:11 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:12 2010 TLS: Initial packet from 67.228.223.12:3389, sid=128becf9 f62adf0c Tue Oct 26 12:33:12 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:12 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:12 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:12 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:12 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:17 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:17 2010 Re-using SSL/TLS context Tue Oct 26 12:33:17 2010 LZO compression initialized Tue Oct 26 12:33:17 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:17 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:17 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:17 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:17 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:20 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:20 2010 SIGTERM[hard,init_instance] received, process exiting Guys I am extremely sorry for not presenting my error Log properly, please forgive me and give me your valuable advice. I am using windows 7 and I am using openvpn mainly to bypass censorship at UAE. I am using only client config file. Ca.crt file is in config folder Thanks and regards Nitin My error Log with Config1 file Tue Oct 26 21:24:34 2010 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Tue Oct 26 21:24:46 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 21:24:46 2010 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Oct 26 21:24:46 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 21:24:46 2010 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 21:24:46 2010 LZO compression initialized Tue Oct 26 21:24:46 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 21:24:46 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 21:24:46 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 21:24:46 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 21:24:46 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 21:24:47 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TLS: Initial packet from 67.228.223.12:3389, sid=4244e662 e5a0572a Tue Oct 26 21:24:47 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 21:24:47 2010 TCP/UDP: Closing socket Tue Oct 26 21:24:47 2010 SIGUSR1[soft,tls-error] received, process restarting client config file: client dev tun proto tcp remote openvpn1.flashvpn.com 3389 float resolv-retry infinite nobind persist-key persist-tun ca ca.crt ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 auth-user-pass route-method exe route-delay 2

  Read the article

• windows 7 64 bit visual studio 2008 libtiff build nmake error

  - by user1244539

  I am trying to build tiff 4.0.2 on my Windows 7 x64 system with Visual Studio 2008, but it was showing errors: C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2347) : error C2061: syntax error : identifier 'QINT' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2362) : error C2059: syntax error : '}' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2397) : error C2061: syntax error : identifier 'JOYCAPS' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2397) : error C2059: syntax error : ';' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2398) : error C2061: syntax error : identifier 'PJOYCAPS' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2398) : error C2059: syntax error : ';' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2399) : error C2061: syntax error : identifier 'NPJOYCAPS' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2399) : error C2059: syntax error : ';' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2400) : error C2061: syntax error : identifier 'LPJOYCAPS' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2400) : error C2059: syntax error : ';' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2146: syntax error : missing ')' before identifier 'pjc' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2081: 'LPJOYCAPSA' : name in formal parameter list illegal C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2061: syntax error : identifier 'pjc' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2059: syntax error : ';' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2059: syntax error : ',' C:\Program Files\Microsoft SDKs\Windows\v6.0A\include\mmsystem.h(2534) : error C2059: syntax error : ')' NMAKE: fatal error u1077: "c:\program files(x86)\microsoft visual studio 9.0\vc\bin\cl.exe": return code '0x2' This is what I was doing: Extracted tiff 4.0.2 In VS 2008 x64 Win 7 command prompt setting the environment for x86 by running vcvars32.bat Changing the path to tiff 4.0.2/libtiff folder Running nmake /f makefile.vc to create a static library of libtiff Following these steps in Windows XP generates the .lib file but in Windows 7 it fails. This is the first time I'm making any .lib files.

  Read the article

• Samba and Windows 7

  - by John Gaughan

  I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

  Read the article

• Giving VPN connections access to all locations?

  - by Jeff

  I have asked a similiar question, but didn't get any answers so i am going to try and rephrase. i have 4 locations corporate and 3 remotes when you are at the corporate location, you have full access to all networks. 192.168.3.x 192.168.2.x 192.168.1.x 192.168.0.x all locations are connected via site-to-site vpn with the corporate location. if you are at a remote location, you have access to that location & the corporate location. the corporate location handles all VPN traffic. however, when you VPN into the corporate location, you can not see outside the corporate location. can anyone provide some information or a link explaining how to allow the VPN users to see all locations? thanks static route configuration: Gateway of last resort is 207.255.x.1 to network 0.0.0.0 C 207.255.x.0 255.255.255.0 is directly connected, outside S 10.0.1.6 255.255.255.255 [1/0] via 207.255.x.1, outside S 10.0.1.5 255.255.255.255 [1/0] via 207.255.x.1, outside S 192.168.0.0 255.255.255.0 [1/0] via 192.168.0.1, inside C 192.168.1.0 255.255.255.0 is directly connected, inside S 192.168.2.0 255.255.255.0 [1/0] via 192.168.2.1, inside S 192.168.3.0 255.255.255.0 [1/0] via 192.168.3.1, inside S* 0.0.0.0 0.0.0.0 [1/0] via 207.255.x.1, outside [1/0] via 192.168.1.1, outside

  Read the article

• nginx rewrite or internal redirection cycle

  - by gyre

  Im banging my head against a table trying to figure out what is causing redirection cycle in my nginx configuration when trying to access URL which does not exist Configuration goes as follows: server { listen 127.0.0.1:8080; server_name .somedomain.com; root /var/www/somedomain.com; access_log /var/log/nginx/somedomain.com-access.nginx.log; error_log /var/log/nginx/somedomain.com-error.nginx.log debug; location ~* \.php.$ { # Proxy all requests with an URI ending with .php* # (includes PHP, PHP3, PHP4, PHP5...) include /etc/nginx/fastcgi.conf; } # all other files location / { root /var/www/somedomain.com; try_files $uri $uri/ ; } error_page 404 /errors/404.html; location /errors/ { alias /var/www/errors/; } #this loads custom logging configuration which disables favicon error logging include /etc/nginx/drop.conf; } this domain is a simple STATIC HTML site just for some testing purposes. I'd expect that the error_page directive would kick in in response to PHP-FPM not being able to find given files as I have fastcgi_intercept_errors on; in http block and nave error_page set up, but I'm guessing the request fails even before that somewhere on internal redirects. Any help would be much appreciated.

  Read the article

• Tomcat performing terribly for no apparent reason

  - by John

  We're running a game application .WAR on Tomcat 6 on an Amazon EC2 server, 8 core processor, 7gb RAM. The application uses a MySQL database hosted on Amazon RDS. This Facebook application takes ages to access when a mere 20-30 users are playing it. Big difference from 1-2 users. The entire .WAR is ~4mb, all static content hosted elsewhere. The server has never been close to running out of RAM. The CPU utilization has never been higher than 13.5-14%. Even with ~500 users that completely slowed everything to a standstill. The thread count or threadpools isn't close to being maxed out. I heightened maxthreads but it didn't make a noticeable difference. My theory is that Tomcat can only use one processor core, which would explain why it was slowed to a halt even though CPU usage was stably at 13-14% at the activity spike. But I'm struggling to understand why it would only use one CPU core. There is no processor cap in server.xml. The app contains several servlets (4 or 5). There is no mention of SingleThreadModel in the Java code. WHAT could be causing the application to run extremely slowly? If there is only 1-5 people on the application it runs fine. With 20-30 people it's barely contactable.

  Read the article

• Nginx - Enable PHP for all hosts

  - by F21

  I am currently testing out nginx and have set up some virtual hosts by putting configurations for each virtual host in its own file in a folder called sites-enabled. I then ask nginx to load all those config files using: include C:/nginx/sites-enabled/*.conf; This is my current config: http { server_names_hash_bucket_size 64; include mime.types; include C:/nginx/sites-enabled/*.conf; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { listen 80; root C:/www-root; #charset koi8-r; #access_log logs/host.access.log main; location / { index index.html index.htm index.php; } # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } server{ server_name localhost; } } And this is one of the configs for a virtual host: server { server_name testsubdomain.testdomain.com root C:/www-root/testsubdomain.testdomain.com; } The problem is that for testsubdomain.testdomain.com, I cannot get php scripts to run unless I have defined a location block with fastcgi parameters for it. What I would like to do is to be able to enable PHP for all hosted sites on this server (without having to add a PHP location block with fastcgi parameters) for maintainability. This is so that if I need to change any fastcgi values for PHP, I can just change it in 1 location. Is this something that's possible for nginx? If so, how can this be done?

  Read the article

• httpd.config Easy Apache WHM CentOS

  - by jessie

  First let me explain how I got to this situation. I run a Streaming Video Site. Videos are about 100-250MB in size at any given time there are 500 people on the site. So I guess that would make then static. Recently My site started getting really slow and the only way to fix it temporarily was to restart apache. Now there was no change in traffic that could have caused this. My site is not being attacked. My hosting company recomended to implement mpm_mod and suPHP. They did that by using Easy Apache in WHMS. Then everything was working fine but a little slow. I researched around and to my understanding that mpm will do that but be more table. I was told that installing FastCGI would speed things up just enough. Well that made everything worse. The site is slow and time's out. I used WHM and took off fastCGI but its still the same, it seems like everything i do as of now nothing changes. I even did a roll back on the htconfig file but that didn't work. I'm not sure how to fix this. and my hosting network guy wont be able to touch the problem until Tuesday. I have root access.

  Read the article

• KVM network bridge with two NICs

  - by Eil

  Greetings, I'm trying to set up bridged networking with KVM and am getting nowhere. There are docs and tutorials on the subject, but they all seem to conflict or don't provide enough info. I was wondering if someone can give me a high-level overview of how to get this working. I can probably work out the details myself (configuring the interfaces, adding routes, etc), I just need help on the big picture: how everything is interconnected. I have a RHEL5 server with KVM installed and running. It has two physical NICs, eth0 and eth1 in the same VLAN. I would like to use eth1 for all traffic between the guests and the rest of the network and reserve eth0 for host management, guest migrations, etc if possible. I'm not picky about which one gets the default route, although it would be nice if we could make it eth0. All of the guests will have static IPs. I would prefer that when a new guest is added, the networking configuration only needs to be set from within the guest itself. Basically, I want this: eth0: all host traffic eth1: all guest traffic Open to any other suggestions if this isn't possible or will be kludgy/difficult. Pointers to existing documentation might not be helpful since I've already been though just about everything out there. Thanks for any help.

  Read the article

• Pinging an external server through OpenVPN tunnel doesn’t work

  - by qdii

  I have an OpenVPN server and a client, and I want to use this tunnel to access not only 10.0.8.0/24 but the whole internet. So far, pinging the server from the client through the tun0 interface works, and vice versa. However, pinging www.google.com from the client through tun0 doesn’t work (all packets are lost). I figured that I should configure the server so that any packet coming from tun0 in destination of the internet be forwarded, so I came up with this iptables config line: interface_connecting_to_the_internet='eth0' interface_openvpn='tun0' internet_ip_address=`ifconfig "$interface_connecting_to_the_internet" | sed -n s'/.*inet \([0-9.]*\).*/\1/p'` iptables -t nat -A POSTROUTING -o "${interface_connecting_to_the_internet}" -j SNAT --to-source "${internet_ip_address}" echo '1' > /proc/sys/net/ipv4/ip_forward Yet, this doesn’t work, the packets are still lost and I am wondering what could possibly be wrong with my setup. Some details: ip route gives on the server: default via 176.31.127.254 dev eth0 metric 3 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 127.0.0.0/8 via 127.0.0.1 dev lo 176.31.127.0/24 dev eth0 proto kernel scope link src 176.31.127.109 ip route gives on the client: default via 192.168.1.1 dev wlan0 proto static 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 127.0.0.0/8 via 127.0.0.1 dev lo scope link 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.109 client uses wifi adapter wlan0 and TUN adapter tun0. server uses ethernet adapter eth0 and TUN adapter tun0. the VPN spans on 10.0.8.0/24 both client and linux are using Linux 3.6.1.

  Read the article

• Configuration for Router Behind Uverse 2Wire

  - by Nori

  I have a 2Wire Uverse router(RG). I'm not particularly fond of it and want to use it as a modem only. I have a Linksys router with Tomato firmware on it and want that to be configured as the router. Most of the "guides" I've seen in my searches has been to enable DMZ Plus mode, but I don't see a way to make that work while my router has a static IP address. I played with it for quite some time yesterday and didn't see a way to get it to work. Then I ran across a setting in broadband for configuring another network. I played with that for a little bit but ran out of time and couldn't get it to work. So my question is for anyone out there who has Uverse and successfully setup a Tomato based firmware router behind the RG. How did you get it configured? I'm sure if I continued playing with it I could get it to work, but if someone out there already has it working then that would make my life easier. Thoughts? Thanks.

  Read the article

• mod_deflate doesn't work [closed]

  - by kikio

  I want to gzip my static files. so put this in .htaccess: <IfModule mod_deflate.c> AddOutputFilterByType DEFLATE text/text text/html text/plain text/xml text/css application/x-javascript application/javascript </IfModule> and looked for mod_deflate in phpinfo() output Loaded Modules section, and I found it. But when I track server responses with Firebug, no gzipped file can be found: HTTP/1.1 200 OK Date: Sat, 08 Sep 2012 21:41:21 GMT Last-Modified: Sat, 08 Sep 2012 21:26:04 GMT Accept-Ranges: bytes Cache-Control: max-age=604800 Expires: Sat, 15 Sep 2012 21:41:21 GMT Vary: Accept-Encoding Keep-Alive: timeout=3, max=50 Connection: Keep-Alive Content-Type: text/css Content-Length: 18206 What's the problem? I'm sure I have mod_deflate enabled (according to php apache_get_modules()). UPDATE: the request headers: GET /d/jquery-ui.css HTTP/1.1 Host: 127.0.0.1 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:15.0) Gecko/20100101 Firefox/15.0.1 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Pragma: no-cache Cache-Control: no-cache

  Read the article

• How to eliminate the downtime when a dynamic IP address changes?

  - by xenon

  We currently have a number of client computers linked up to a database server (MS SQL 2008) for replication. The database server recognises the computers based on their Windows hostname. We are using dynamic IP addresses at this time because we tend to change the computers’ hardware quite frequently, and so the MAC address may be different. Unless static IP has a good way for us to manage frequent changing of MAC addresses, we are keeping it to dynamic IP. The problem with dynamic IP addresses, however, is that when a client fetches an new IP from the DHCP, ie, there is a change in the IP address, there is going to have a downtime for the hostname to reflect the new IP address, the client’s DNS cache of the hostname to reload, and also the server’s DNS cache to reload to see the new IP from the hostname. All of these have different timings and the delay can be really bad at times. Restarting the computer doesn't work all the time too. The clients are on Windows 7. How can I eliminate the amount of downtime required when there is a change in IP in the case of dynamic IP addresses?

  Read the article

• Connecting to IPv6 hosts when mobile and on a Surface?

  - by Cerebrate

  Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

  Read the article

• windows 2003 under Hyper-V - can't send/receive ping

  - by glaucon

  I've installed Windows 2003 x64 R2 SP2 under Hyper-V (the Windows Pro 8 edition). I have a NIC configured but I can't move any traffic on it. In particular I can't send or receive Pings. Scoreboard There is a second VM running Ubuntu under the Windows 8 host which is able to send and receive pings from the host O/S . When I try to ping from Windows 2003 guest to Windows 8 host I get 'Request Timed Out'. When I try to ping from Windows 8 host to Windows 2003 guest I get 'Reply from 192.168.10.107 Destination Host Unreachable'. There's no problem pinging from the Ubuntu guest to the Windows 8 host and no problem pinging from the Windows 8 host to the Unbuntu guest. Environment Integration services are installed on Windows 2003. The windows 2003 needs a static IP address of 192.168.10.15. The Windows 2003 ipconfig output looks like this : While the host o/s ipconfig output looks like this : Event Logs The only things I can see in the event logs which is (a) looks signifcant and (b) is not related to the lack of networking is this : I'm not sure if that's significant or not. Hyper-V and NICs When the Windows 2003 guest was first booted it had no NIC; I subsequently added a 'Legacy Network Connector' which I couldn't get Windows 2003 to recognise; I subsequently removed that and added a 'Standard Network Connector' and at least on the surface this works ... only it doesn't. 'Virtual Network Type' is external. Although I've only mentioned ping there's no other evidence of network activity. 'Allow incoming echo request' is enabled on the Windows 2003 guest. HELP ? What else should I look at or do to resolve this problem ? EDIT 1: I should have said that I turned off the firewall on the W2003 server for a while and retested the pings; same result.

  Read the article

• Webserver optimization

  - by f-aminov

  Hi guys! I have a website hosted on a VPS (512Mb - minimum guranteed memory, 510Mhz proccessor, Debian 5.0 Lenny, Apache 2.2.9 with nginx 0.7.65 as a frontend to serve static content, MySQL 5.1.44, PHP 5.3.2 with APC caching). I'm a web developer, so I'm not very good at optimizing servers, but I've managed to install and setup all those neccessary components (LAMP, nginx, etc.). After that I decided to stress test my website (which uses Drupal 6.16 with caching and all possible optimization enabled) using a utility called "Webserver Stress Tool 7". And it seems to me that the results aren't any good - here is a graph (sorry, as a new user I'm not allowed to post images) As you can see the response time depending on amount of simultaneous users increases very quickly. With 10 simultaneous users the time is about 1000ms, with 100 simultaneous users it's about 15000ms (15s!). The question is do you think this is normal behavior for such a server or something is wrong with the settings and optimization? If you think something is wrong what particulary could be wrong? Any other suggestion how to speed this a little bit up?

  Read the article

• Running DNS locally for home network

  - by Roy Rico

  I have a small home network that just got larger ( New roommate, My existing roommate got a laptop (on top of her computer)j, my friends coming over with laptop, etc ). I'd like to run a local DNS server for lookups of my local network stuff (fileserver.local, windowsTV.local, machineA.local, machineB.local, appletv.local). I used to have a business line with a static IP, and run bind/named internally. However, now, I have a normal account. My ISP's DNS servers are constantly changing (for whatever reasons my ISP doesn't like to keep the same IP range for long). I need my local DNS to be automatically updated to use my ISP's DNS for external traffic, but be able to maintain an internal DNS server (getting to update the hosts file is being a hassle with every new machine on top of rebuilding existing machines with win7 or Ubuntu 9.04). Additionally, My ISP's DNS servers often crash or become unresponsive. Are there any open DNS servers that are reliable (i don't want to reconfig every day) that I could use as my primary, then if those fail, then use my ISP's? UPDATE: Also looking for each workstation to be able to use dhcp to connect, but instead of getting ISP dns servers, getting my internal one.... Thanks

  Read the article

• Error in Bind9 named.conf file. Bind won't start.

  - by tj111

  I'm trying to setup a DNS server on an Ubuntu Server machine (10.04). I configured an entry in named.conf.local to test it, but when trying to restart bind9 I get the following error: * Starting domain name service... bind9 [fail] So I checked the output of syslog and this is what I get. May 20 18:11:13 empression-server1 named[4700]: starting BIND 9.7.0-P1 -u bind May 20 18:11:13 empression-server1 named[4700]: built with '--prefix=/usr' '--mandir=/usr/share/man' '--infodir=/usr/share/info' '--sysconfdir=/etc/bind' '--localstatedir=/var' '--enable-threads' '--enable-largefile' '--with-libtool' '--enable-shared' '--enable-static' '--with-openssl=/usr' '--with-gssapi=/usr' '--with-gnu-ld' '--with-dlz-postgres=no' '--with-dlz-mysql=no' '--with-dlz-bdb=yes' '--with-dlz-filesystem=yes' '--with-dlz-ldap=yes' '--with-dlz-stub=yes' '--with-geoip=/usr' '--enable-ipv6' 'CFLAGS=-fno-strict-aliasing -DDIG_SIGCHASE -O2' 'LDFLAGS=-Wl,-Bsymbolic-functions' 'CPPFLAGS=' May 20 18:11:13 empression-server1 named[4700]: adjusted limit on open files from 1024 to 1048576 May 20 18:11:13 empression-server1 named[4700]: found 4 CPUs, using 4 worker threads May 20 18:11:13 empression-server1 named[4700]: using up to 4096 sockets May 20 18:11:13 empression-server1 named[4700]: loading configuration from '/etc/bind/named.conf' May 20 18:11:13 empression-server1 named[4700]: /etc/bind/named.conf:10: missing ';' before 'include' May 20 18:11:13 empression-server1 named[4700]: loading configuration: failure May 20 18:11:13 empression-server1 named[4700]: exiting (due to fatal error) So it thinks I have an error in the default named.conf file, which is pretty ridiculous. I went through it and deleted a blank line just for the hell of it, but I can't see how it figures there's an error in there. Note that before this I did have an error in named.conf.local, but it showed up properly in syslog and I fixed it, so it is reporting the correct file. Here is the contents of named.conf: // This is the primary configuration file for the BIND DNS server named. // // Please read /usr/share/doc/bind9/README.Debian.gz for information on the // structure of BIND configuration files in Debian, *BEFORE* you customize // this configuration file. // // If you are just adding zones, please do that in /etc/bind/named.conf.local include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones";

  Read the article

• Debian network bridge configuration - /etc/network/interfaces

  - by Mathias

  I'm running a Lenny Xen dom0 hosting multiple virtual machines in a routed IP setup. To get an additional private subnet, I created the bridge xenbr0 in the dom0 with the following commands: brctl addbr xenbr0 ifconfig xenbr0 10.0.0.1 netmask 255.255.255.0 ifconfig xenbr0 up This works as expected, and domU interfaces are added to the bridge by Xen on VM start. My only problem is: how the heck do i specify this configuration in /etc/network/interfaces that it remains permanent and the bridge is available after a reboot? I tried the following config as found on a lot of tutorials: auto xenbr0 iface xenbr0 inet static address 10.0.0.1 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 bridge_stp no I get 2 different errors, depending on if the bridge already exists or not. If it doesn't exist: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). SIOCSIFADDR: No such device xenbr0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device xenbr0: ERROR while getting interface flags: No such device xenbr0: ERROR while getting interface flags: No such device Failed to bring up xenbr0. done. And if it exists: root@dom0:~# brctl show bridge name bridge id STP enabled interfaces xenbr0 8000.000000000000 no root@dom0:~# /etc/init.d/networking restart Reconfiguring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface xenbr0 before doing NFS mounts (warning). RTNETLINK answers: File exists Failed to bring up xenbr0. done. Could anyone point me in the right direction please? The bridge works fine when created manually, i just need the right config file entries. The most tutorials I found add some devices to the bridge in the config, is that maybe the problem why it is not working? I don't have any interfaces I want to add to the bridge on creation as they get added later on VM start... Thanks, Mathias

  Read the article

< Previous Page | 412 413 414 415 416 417 418 419 420 421 422 423  | Next Page >