Search Results

Search found 12780 results on 512 pages for 'webmaster tools'.

Page 418/512 | < Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >

  • How to enable Ipv6 on my ubunutu 11.04 virtual machine

    - by liv2hak
    I have installed 3 VM's on my PC.(Ubuntu 11.04).I want to setup an IPV6 network to review and test some of the IPV6 tools like NDPMonitor.(monitors ICMP messages of Neighbour Discovery Protocol.) IP v6 addresses are as follows. linux_router - fe80::a00:27ff:fed5:f7e9/64 labhack1 - fe80::a00:27ff:fed2:8bd1/64 labhack2 - fe80::a00:27ff:fed7:2f2d/64 The below commands have been run on both linux_router and labhack1. sudo ip r a 2001:468:181:f100::/64 dev eth0 sudo vim /etc/radvd.conf /file looks like below./ interface eth0 { AdvSendAdvert on; /*means that we are sending out advertisments.*/ MinRtrAdvInterval 5; /*these options control how often advertisments are sent*/ MaxRtrAdvInterval 15; /*these are not mandatory but valueable settings.*/ prefix fe80::a00:27ff::/64 { AdvOnLink on; /*Says to the host everyone sharing this prefix is on the sam local link as you.*/ AdvAutonomous on; /*Says to a host: "Use this prefix to autoconfigure your address"*/ }; }; sudo sysctl -w net.ipv6.conf.all.forwarding=1 I try to do a ping6 -I eth0 fe80::a00:27ff:fed5:f7e9 I get Destination unreachable: Address unreachable.I am not sure what I am doing wrong here.I am a beginner at linux administration.Basically I think I am missing whatever is analogous to physically connecting VM's.Any help that would point me in the right direction would be greatly appreciated.

    Read the article

  • How to setup an IPSec / GRE tunnel on Windows Server 2008

    - by qbeuek
    I have a Windows Server 2008 that has a single network interface configured with a public IP address. My business partner has a private network. From my server, I need to access all the devices on his private network, and those devices must be able to access my server. My business partner has a standard solution for these requirements. They will setup an IPSec + GRE tunnel to my server. They told me, that I will need an additional public IP address for this to work. If it really is necessary, there is no problem, I can get an additional public IP address, although it will be assigned to the same physical network interface. I assume that on my server I will have both public IP addresses and also the private IP address from the tunnel (the same that is visible for the devices inside the private network). What alternatives do I have? Is it possible to configure this tunnel on my Windows Server 2008? Can it be done using only Windows tools, or do I need an additional free / commercial VPN software? If it cannot be done directly on Windows, can I setup an additional virtual machine running Linux, that will handle the IPSec + GRE tasks? How to do it? If it cannot be done on a virtual linux box, will I have to buy and setup a Cisco router to handle the IPSec + GRE tasks? Thanks for your opinions. I'm watching this question to clarify any issues or questions.

    Read the article

  • How to populate RRD database with CPU and MEM usage data?

    - by Tomaszs
    I have a Lighttpd server (on Centos) and would like to display 4 graphs: lighttpd traffic, lighttpd requests per second, CPU usage and MEM usage. I've set place for rrd database for lighttpd config like this: rrdtool.binary = "/usr/bin/rrdtool" rrdtool.db-name = "/var/www/lighttpd.rrd" And put into my WWW cgi-bin sh file that gets data from lighttpd RRD file and creates graphs of traffic and requests per second like this: #!/bin/sh RRDTOOL=/usr/bin/rrdtool OUTDIR=//var/www/graphs INFILE=/var/www/lighttpd.rrd OUTPRE=lighttpd-traffic WIDTH=400 HEIGHT=100 DISP="-v bytes --title TrafficWebserver \ DEF:binraw=$INFILE:InOctets:AVERAGE \ DEF:binmaxraw=$INFILE:InOctets:MAX \ DEF:binminraw=$INFILE:InOctets:MIN \ DEF:bout=$INFILE:OutOctets:AVERAGE \ DEF:boutmax=$INFILE:OutOctets:MAX \ DEF:boutmin=$INFILE:OutOctets:MIN \ CDEF:bin=binraw,-1,* \ CDEF:binmax=binmaxraw,-1,* \ CDEF:binmin=binminraw,-1,* \ CDEF:binminmax=binmaxraw,binminraw,- \ CDEF:boutminmax=boutmax,boutmin,- \ AREA:binmin#ffffff: \ STACK:binmax#f00000: \ LINE1:binmin#a0a0a0: \ LINE1:binmax#a0a0a0: \ LINE2:bin#efb71d:incoming \ GPRINT:bin:MIN:%.2lf \ GPRINT:bin:AVERAGE:%.2lf \ GPRINT:bin:MAX:%.2lf \ AREA:boutmin#ffffff: \ STACK:boutminmax#00f000: \ LINE1:boutmin#a0a0a0: \ LINE1:boutmax#a0a0a0: \ LINE2:bout#a0a735:outgoing \ GPRINT:bout:MIN:%.2lf \ GPRINT:bout:AVERAGE:%.2lf \ GPRINT:bout:MAX:%.2lf \ " $RRDTOOL graph $OUTDIR/$OUTPRE-hour.png -a PNG --start -14400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-day.png -a PNG --start -86400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-month.png -a PNG --start -2592000 $DISP -w $WIDTH -h $HEIGHT OUTPRE=lighttpd-requests DISP="-v req --title RequestsperSecond -u 1 \ DEF:req=$INFILE:Requests:AVERAGE \ DEF:reqmax=$INFILE:Requests:MAX \ DEF:reqmin=$INFILE:Requests:MIN \ CDEF:reqminmax=reqmax,reqmin,- \ AREA:reqmin#ffffff: \ STACK:reqminmax#00f000: \ LINE1:reqmin#a0a0a0: \ LINE1:reqmax#a0a0a0: \ LINE2:req#00a735:requests" $RRDTOOL graph $OUTDIR/$OUTPRE-hour.png -a PNG --start -14400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-day.png -a PNG --start -86400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-month.png -a PNG --start -2592000 $DISP -w $WIDTH -h $HEIGHT Basically it's not my script, i get it from somewhere from the internet. Now i would like to do the same for CPU usage and MEM usage. I don't like to use any additional packages! As you can see lighttpd populates lighttpd.rrd file with traffic data and requests per second. Now i would like to the system to populate second rrd file with CPU and MEM usage, so i can add to sh file code to generate graphs for this data. How can I populate RRD file with CPU and MEM usage data? Please, NO THIRD-PARTY tools !

    Read the article

  • Setting up Mako with Cherrypy on nginx through FastCGI

    - by xuniluser
    I'm trying to use TemplateLookup from Mako, but can't seem to get it to work. Layout of the test site is: /var/www main.py templates/ index.html Nginx's config is setup as: location / { fastcgi_pass 127.0.0.1:8080; fastcgi_param SERVER_NAME $server_name; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param QUERY_STRING $query_string; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_pass_header Authorization; fastcgi_intercept_errors off; } Cherrypy's config has: [global] server.socket_port = 8080 server.thread_pool = 10 engine.autoreload_on = False tools.sessions.on = True A simple cherrypy setup in main.py seems to work fine. import cherrypy class Main: @cherrypy.expose def index(self): return 'Hello' cherrypy.tree.mount(Main(), '/', config='config') Now, if I modify this to use Mako's template lookup, I get a 500 error. I know it has something to do with serving static files, but I've tried over a dozen different configurations accoring to the cherrypy wiki, but none of them work. Here's a bare setup I have for the templates: import cherrypy from mako.template import Template from mako.lookup import TemplateLookup templates = TemplateLookup(directories=['templates'], output_encoding='utf-8') class Main: @cherrypy.expose def index(self): return templates.get_template('index.html').render(msg='hello') cherrypy.tree.mount(Main(), '/', config='config') Does anyone know how I can get this to work ?

    Read the article

  • Very slow browsing shared folder XP client/host

    - by Ickster
    I have a pretty straightforward setup where I'm storing media files on an XP pro machine, and sharing the folder to be accessed by other XP pro machines around the house. (Typically, there's only one client accessing the share at a time, although there may be several with the share mounted.) It's been working just fine for years, but I've recently started having some problems. A couple of days ago, the host PC had power disconnected while it was running. It was restarted and everything seemed fine initially, but since then browsing the shared folder from client machines has been extremely slow and actually reading data is all but impossible. The problem exists in every access method I've tried: Windows Explorer, VLC dialogs, command line, etc. My first thought was that the disk was experiencing problems, but there are no problems viewing the files locally on the host machine. My second thought was that there was a network problem on the host machine, so I removed and reinstalled drivers for the NIC with no change. My third thought was that there might've been a problem elsewhere on the network, so I swapped out hardware to no avail. I'm regrouping and trying to come up with a methodical approach to figuring out what might be wrong. I would of course be thrilled if you can suggest specific problems (Microsoft KB articles, etc.) that I might check, but I'm not expecting a silver bullet. If you can help me outline an approach to identify the problem (including recommended tools, e.g., disk checkers, network analyzers, etc.) I'd greatly appreciate it.

    Read the article

  • Windows Home Server installation fails because it can't find the DVD drive anymore

    - by BBlake
    I've got an old Dell Dimension 8300 desktop I decided to convert into a WHS box. I popped in a pair of 1 TB SATA drives, which were recognized fine by the BIOS and the currently installed OS (XP), so I decided to go ahead and install WHS. Near the end of the installation, WHS acts like it can no longer find the DVD drives (either of them, the box has a DVDROM and a DVDRW). The specific error is gives is the "Can't configure storage" error. I've found several forums where people say they get this error if they remove the boot DVD during the installation (at the time of the first reboot). However, I never removed the DVD. After the error, if fails into WHS, so it did mostly install and I can work with WHS. However, it refuses to recognize the network card, video card and while it shows the two DVD drives, any CD/DVD I insert in either drive the system says is corrupted and unreadable, even though none of them are. I've tried several reinstalls both removing and not removing the DVD, but the result is the same regardless. Any other tricks anyone found? If I can't figure this out, maybe I'll just install SBS2008 and fake it up to be similar to WHS with some addin tools. Shouldn't be too hard to create something since WHS is based on SBS2003 anyway.

    Read the article

  • How do I properly configure a ZipInstaller .zic file?

    - by Iszi Rory or Isznti
    As of version 1.20, ZipInstaller is supposed to support the use of a configuration file to customize its installation options. Generally, all the options I want to use are available through the dialog so I really haven't bothered with the configuration file until now. The problem now is that certain tools, such as PsTools from Sysinternals, do not properly show their Product Name to ZipInstaller. ZipInstaller's dialog will let you customize the Start Menu folder and Program Files folder, but that still doesn't change the Product Name that it sees for the software. So, instead of having "PsTools" in my Add/Remove Programs, I get "Sysinternals Software". For some things, the situation is even more confusing. For example, the NIST SP 800-53 Reference Database Application gets installed as "FileMaker Pro Runtime". To rectify this, I've tried to use the aforementioned .zic configuration file. As I understand it, it's a basic INI file you create and put in the root of the ZIP file. ZipInstaller is supposed to read that file, and adjust its parameters accordingly. Mine looks like this: [install] ProductName=NIST_SP_800-53 ProductVersion=1.4.1 CompanyName=NIST Description=NIST_SP_800-53 InstallFolder=%zi.ProgramFiles%\%zi.ProductName% StartMenuFolder=%zi.CompanyName%\%zi.ProductName% I've named it `~zipinst~.zic and placed it in the root of the ZIP file, but when I run ZipInstaller it doesn't seem to recognize any of the information I've given it in the .zic file. What might I be doing wrong here?

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • How Do I Install Latest Java Plugin on Ubuntu 8.04 LTS with Custom Firefox 3.6.3?

    - by Volomike
    I have Ubuntu 8.04 LTS and will need to remain on that for awhile as I am a programmer and cannot disturb what I'm doing in the middle of a project. As you know, it doesn't want to install the latest Firefox by default and keeps me in the stone age. So, I had to install my own Firefox. I did so and with relative ease I was able to install the Flash plugin using the normal 'ln -s' technique one usually does with /usr/lib/firefox/plugins. Now I need to do a Gotomypc.com task and it requires Java -- moan -- so I need to figure out how to install Java. I downloaded and installed the latest Java plugin in /usr/java, and I do see underneath that layer of folders a plugins folder with a .so file. So, I went to /usr/lib/firefox/plugins and did this: ln -s /usr/java/jre1.6.0_20/plugin/i386/ns7/libjavaplugin_oji.so Then, I also read on the web that one has to create a ~/.mozilla/plugins folder, cd into it, and then run the same ln -s command again. Another site recommended finding one's ~/.mozilla/firefox and renaming it to ~/.mozilla/firefox.old (after you backed up your bookmarks) and then launching firefox again so that it creates ~/.mozilla/firefox and uses the new Java plugin. Well, all these attempts have completely failed and it is incredibly frustrating. I do about:plugins to see my plugins and all I get are the Flash and the default null plugin. I do not see the Java one. Also, they said on my tools menu with Firefox 3.6.3 I would see a Java Console menu and I don't see that either. I found a pluginreg.dat somewhere deep under ~/.mozilla/firefox, but it does not list the Java plugin inside -- only Flash and the null plugin. Please help me install Java. I need to help a client out and need to connect to his PC remotely with gotomypc, which requires Java inside firefox.

    Read the article

  • How can I connect integrated webcam with virtualbox

    - by Mike Stumpf
    I am trying to use a Windows XP VM for VirtualBox on my Windows 8.1 laptop. I have tried the usual attaching USB device but I get an error saying "USB device is busy with previous request". My webcam is not active in any applications and this happens after a clean reboot of the host, the guest, and VirtualBox. Here are the details: Host -HP Pavilion 17 Notebook PC (stock) -Windows 8.1 -AMD A10-5750M APU -HP Truevision HD (integrated webcam) VM I got the VM here: http://www.modern.ie/en-us/virtualization-tools VirtualBox -VirtualBox 4.3.12 installed -VirtualBox Extension pack installed -Guest additions are installed for 4.3.12 -Enable USB Controller is checked -It does not matter if enable 2.0 controller is checked or not -It does not matter if a USB device filter is set up for the webcam or not -Here is the error message: Failed to attach the USB device DDFEQ01G45BFBV HP Truevision HD [0004] to the virtual machine IE8 - WinXP. USB device 'DDFEQ01G45BFBV HP Truevision HD' with UUID {7a2e2a45-974d-482b-9b4e-9f9abbcd0ebb} is busy with a previous request. Please try again later. Result Code: E_INVALIDARG (0x80070057) Component: HostUSBDevice Interface: IHostUSBDevice {173b4b44-d268-4334-a00d-b6521c9a740a} Callee: IConsole {8ab7c520-2442-4b66-8d74-4ff1e195d2b6} I read on some VirtualBox forums that disabling USB 2.0 support in the host BIOS solved their issue but I wanted to know if there were any other ideas before I muck around in there. Thanks

    Read the article

  • Strange IIS hits originating from Trend Micro

    - by TesterTurnedDeveloper
    I'm trying to trace thru an error on a extranet site I maintain. I've had a look thru the logs, and I'm seeing hits originate from these IP addresses: 216.104.15.130 216.104.15.138 216.104.15.142 216.104.15.13 150.70.84.49 150.70.84.44 Network-tools.com gives 'TREND MICRO INCORPORATED' as the owner of all these IPs. The hits fail as they aren't sending any cookies (therefore aren't considered logged in). The hits are to pages containing URLs that only the logged in user would see, i.e. ImageEdit.aspx?ImageId=467424. I.e. the server isn't guessing these URLs, someone would have to log into the site to know these URLs exist. Theory: the Trend Antivirus client grabs URLs and sends them to the server for 'extra processing'? Googling around gives me this: http://www.forumpostersunion.com/showthread.php?p=51272 - where people are reporting comment spam from these addresses. The articles says their servers have been hacked (a few months ago, presumably fixed now?). A hacked server wouldn't explain how the URLs have been plucked off the user's PCs. Has anyone seen this before? Anything nefarious going on here?

    Read the article

  • OpenBSD logins via SSH seem to be ignoring my configured radius server

    - by Steve Kemp
    I've installed and configured a radius server upon my localhost - it is delegating auth to a remote LDAP server. Initially things look good: I can test via the console: # export user=skemp # export pass=xxx # radtest $user $pass localhost 1812 $secret Sending Access-Request of id 185 to 127.0.0.1 port 1812 User-Name = "skemp" User-Password = "xxx" NAS-IP-Address = 192.168.1.168 NAS-Port = 1812 rad_recv: Access-Accept packet from host 127.0.0.1 port 1812, id=185, Similarly I can use the login tool to do the same thing: bash-4.0# /usr/libexec/auth/login_radius -d -s login $user radius Password: $pass authorize However remote logins via SSH are failing, and so are invokations of "login" started by root. Looking at /var/log/radiusd.log I see no actual log of success/failure which I do see when using either of the previous tools. Instead sshd is just logging: sshd[23938]: Failed publickey for skemp from 192.168.1.9 sshd[23938]: Failed keyboard-interactive for skemp from 192.168.1.9 port 36259 ssh2 sshd[23938]: Failed password for skemp from 192.168.1.9 port 36259 ssh2 In /etc/login.conf I have this: # Default allowed authentication styles auth-defaults:auth=radius: ... radius:\ :auth=radius:\ :radius-server=localhost:\ :radius-port=1812:\ :radius-timeout=1:\ :radius-retries=5:

    Read the article

  • CryptSvc not matched by Windows 7 Firewall rule

    - by theultramage
    I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

    Read the article

  • Ubuntu server or Debian server (to run C++ apps developed on Ubuntu)

    - by skyeagle
    I have written a number of C++ server side daemons for my website, using my Ubuntu 9.10 dev machine. The C++ apps I mentioned above are "GUI-less" daemons (and libraries used by the daemons). I am now about to host my website and need to decide whether to go with Debian server or Ubuntu server. In a nutshell, here is the situation: I developed on Ubuntu desktop because I preferred the more friendly GUI I would like to deploy on Debian Server because of the (perceived?) robustness of the Debian server over Ubuntu server (I may be totally wrong here - and in fact, this is really what this question is all about) If Debian server is indeed more robust than Ubuntu server, then I have no choice but to go with Debian server - BUT, will my Ubuntu developed C++ apps run on the server? (or do I need to recompile them on the server? (I'd HATE to have to do this, because I want to keep the server machine clean and light - no GUI, no dev tools etc). This last question is really about binary compatability between Ubuntu and Debian. I want the server to be robust, secure and stable, and simply act as a server (i.e. LAMP and very little else - no GUI etc). Given that requirement, and the fact that I need to run my C++ apps (developed on Ubuntu 9.10), I need advice on which OS to choose for the server. Ideally, any advice will be backed with a reason. I am particularly interested in hearing from people who have been in an identical situation, or done something similar.

    Read the article

  • Dedicated server automatic backup solution

    - by Luigi
    I have a dedicated Ubuntu web server in a cloud environment, and I am looking for a nice way to do automated backups. I would like to backup some directories with web apps, and all my MySql databases. As for destination: make snapshots every two hours localy, and every six hours to a remote ftp server. Also delete backup archives older than seven days(localy + ftp), and notify on any problems by email. Now to achieve some of this functionality I use cron + shell script, and http://www.mysqldumper.net/, but really that doesn't answer my needs. Mysqldumper doesn't know automaticly about new databases, and shell script does not notify on problems. It's something I have to check out from time to time, and i don't have trust for. I googled a while, and seems like most people solve this stuff with shell scripts. Is this a method you can trust? Are there any web-gui tools, I'm missing? Maybe there is a smarter startegy for doing this? I'm a little bit confused.

    Read the article

  • Better approach to archiving large amounts of original video footage using optical media (DVD/Blu-ra

    - by Rob
    This question is to share my experience as well as ask for suggestions for better methods. Along with 2 friends, I completed the making of a short documentary film in 2006. Clip is at: http://www.youtube.com/mediamotioninvision The film was edited in Adobe Premiere Pro 1.5 on Windows XP. More details and screenshot here: http://www.flickr.com/photos/smilingrobbie/1350235514/ ( note this is not intended to be a plug, we've moved on from this initial learning curve project ;) ) The film is in 4:3 standard definition 720x576 PAL format. As well as retaining the final 30minute film, I wanted to keep all original files that assembled together to make the film. The footage was 83.5Gb So I archived them to over 20 4.7Gb DVD recordables in the original .avi format (i.e. data DVD-ROM format, NOT DVD-Video Mpeg2) Some .avi DV video files were larger than 4.7Gb so I used 7-zip to split them ( here is a guide as to how to do that: http://www.linglom.com/2008/10/12/how-to-split-a-large-file-using-7-zip/ ) To recombine them, a dos shell command like this would do that: copy /b file.avi.* file.avi would do the job, where .* is a wild card to include all the split parts e.g. 001, 002...00n assuming they are all in the same directory path folder. file.avi is the recombined file identical to the original. Later on, I bought a LG BE06 LU10 USB 2.0 Super-multi Blu-ray burner and archived the footage to 2 (two) x 50Gb BD-R DL discs. Again in the original format, written as files to a BD-R in the BD-R BD-ROM UDF format readable by PC/Mac etc, NOT Blu-ray video/film format. This seems to be a good solution for me, because: the archive is in a robust, reasonably permanent, non-volatile medium, i.e. DVD recordable / Blu-ray (debates about stability of optical media organic chemical dye compounds/substrates aside) the format of the archive is accessible by open source tools or just plain Windows Explorer and it's not in a proprietary format I just thought I'd ask folks for their experience on better methods, if such exist.

    Read the article

  • apache2 mysql authentication module and SHA1 encryption

    - by Luca Rossi
    I found myself in a setup on where I need to enable some authentication method using mysql. I already have an user scheme. That user scheme is working like a charm with MD5 password and CRYPT, but when I turn to SHA1sum it says: [Fri Oct 26 00:03:20 2012] [error] Unsupported encryption type: Sha1sum No useful debug informations on log files. This is my setup and some info: debian6 apache and ssl installed packages: root@sistemichiocciola:/etc/apache2/mods-available# dpkg --list | grep apache ii apache2 2.2.16-6+squeeze8 Apache HTTP Server metapackage ii apache2-mpm-prefork 2.2.16-6+squeeze8 Apache HTTP Server - traditional non-threaded model ii apache2-utils 2.2.16-6+squeeze8 utility programs for webservers ii apache2.2-bin 2.2.16-6+squeeze8 Apache HTTP Server common binary files ii apache2.2-common 2.2.16-6+squeeze8 Apache HTTP Server common files ii libapache2-mod-auth-mysql 4.3.9-13+b1 Apache 2 module for MySQL authentication ii libapache2-mod-php5 5.3.3-7+squeeze14 server-side, HTML-embedded scripting language (Apache 2 module) root@sistemichiocciola:/etc/apache2/sites-enabled# dpkg --list | grep ssl ii libssl-dev 0.9.8o-4squeeze13 SSL development libraries, header files and documentation ii libssl0.9.8 0.9.8o-4squeeze13 SSL shared libraries ii openssl 0.9.8o-4squeeze13 Secure Socket Layer (SSL) binary and related cryptographic tools ii openssl-blacklist 0.5-2 list of blacklisted OpenSSL RSA keys ii ssl-cert 1.0.28 simple debconf wrapper for OpenSSL my vhost setup: AuthMySQL On Auth_MySQL_Host localhost Auth_MySQL_User XXX Auth_MySQL_Password YYY Auth_MySQL_DB users AuthName "Sistemi Chiocciola Sezione Informatica" AuthType Basic # require valid-user require group informatica Auth_MySQL_Encryption_Types Crypt Sha1sum AuthBasicAuthoritative Off AuthUserFile /dev/null Auth_MySQL_Password_Table users Auth_MYSQL_username_field email Auth_MYSQL_password_field password AuthMySQL_Empty_Passwords Off AuthMySQL_Group_Table http_groups Auth_MySQL_Group_Field user_group Have I missed a package/configuration or something?

    Read the article

  • Identifying Hard Drive as performance bottleneck for desktop machines

    - by Programming Hero
    I'm working in a development team where we all use laptops so we can work in multiple locations. These laptops are proving notoriously slow for development work, but at a glance they all look to have the specification for a much faster experience: CPU - Intel Core 2 Duo T7500 Memory - 2GB of RAM We all experience the biggest delays when the hard-drives are being accessed, particularly when swap-files are being thrashed. After doing a little bit of profile, a colleague discovered that our HDDs are seeing Read/Write speeds of about 10MB/sec. This seems abnormally low and we believe it the cause of the problem. Sensibly (though somewhat annoyingly) our business wont blow money on faster drives just to see if it fixes the problem; we need to illustrate this is definitely the problem and that buying some solid-state drives will make it go away. I need some way of showing how 90% of the system resources aren't being used over the course of a day, and that whenever there is utilization, it's all in HDD reads or writes. Are there any tools I could use to provide this information? Does it seem likely the problem is going to be fixed by a faster drive? Should I be looking for alternatives?

    Read the article

  • Is Subversion(SVN) supported on Ubuntu 10.04 LTS 32bit?

    - by Chad
    I've setup subversion on Ubuntu 10.04, but can't get authentication to work. I believe all my config files are setup correctly, However I keep getting prompted for credentials on a SVN CHECKOUT. Like there is an issue with apache2 talking to svnserve. If I allow anonymous access checkout works fine. Does anybody know if there is a known issue with subversion and 10.04 or see a error in my configuration? below is my configuration: # fresh install of Ubuntu 10.04 LTS 32bit sudo apt-get install apache2 apache2-utils -y sudo apt-get install subversion libapache2-svn subversion-tools -y sudo mkdir /svn sudo svnadmin create /svn/DataTeam sudo svnadmin create /svn/ReportingTeam #Setup the svn config file sudo vi /etc/apache2/mods-available/dav_svn.conf #replace file with the following. <Location /svn> DAV svn SVNParentPath /svn/ AuthType Basic AuthName "Subversion Server" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user AuthzSVNAccessFile /etc/apache2/svn_acl </Location> sudo touch /etc/apache2/svn_acl #replace file with the following. [groups] dba_group = tom, jerry report_group = tom [DataTeam:/] @dba_group = rw [ReportingTeam:/] @report_group = rw #Start/Stop subversion automatically sudo /etc/init.d/apache2 restart cd /etc/init.d/ sudo touch subversion sudo cat 'svnserve -d -r /svn' > svnserve sudo cat '/etc/init.d/apache2 restart' >> svnserve sudo chmod +x svnserve sudo update-rc.d svnserve defaults #Add svn users sudo htpasswd -cpb /etc/apache2/dav_svn.passwd tom tom sudo htpasswd -pb /etc/apache2/dav_svn.passwd jerry jerry #Test by performing a checkout sudo svnserve -d -r /svn sudo /etc/init.d/apache2 restart svn checkout http://127.0.0.1/svn/DataTeam /tmp/DataTeam

    Read the article

  • how to initialize two logical drives on a HP P400i controller without reboot

    - by John
    What I am trying to do is initialize two logical drives on a HP P400i embedded controller without a reboot of the system here my current Array config: array A (SAS, Unused Space: 0 MB) logicaldrive 1 (17.9 GB, RAID 5, OK) logicaldrive 2 (17.9 GB, RAID 5, OK) logicaldrive 3 (75.9 GB, RAID 5, OK) logicaldrive 4 (25.0 GB, RAID 5, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 72 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 72 GB, OK) physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 72 GB, OK) array B (SAS, Unused Space: 0 MB) logicaldrive 5 (99 MB, RAID 0, OK) logicaldrive 6 (68.2 GB, RAID 0, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 72 GB, OK) windows 2003 machine running the HpCISs2.sys driver version 6.20.0.32 . I have the ACU and ACU CLI tools installed version 8.28.13.0, P400i firmware version 2.74 . Now what I'd like to do is removes the physical drive 1I:1:4 and delete the two logical drives in array B. then insert a new drive in to bay 4 that contains two new logical drives and have them show up in array B again. So far after I remove the drive and delete the failed logical drives, I insert the new drive and run HPacucli rescan. I get the new drive to show up as unassinged physical drive but I cant figure out now to "for lack of a better word" mount the 2 logical drives on the new unassinged disk. If I reboot the system the array controller picks up the new fourth drive and creates Array B with the drives without problem but I'd really like to not have to reboot the server. Any ideas?

    Read the article

  • Identify differences between MP3 files

    - by Thingomy
    I have 2 old similar directory trees with MP3 files in them. I am happily using tools like diff and Rsync to identify and merge the files that are only present on one side, or are identical, I'm left with a bunch of files that are bitwise different. On running diff over a pair actually different files, (with -a tag to force text analysis) it produces incomprehensible gibberish. I have listened to files from both sides, and they both seem to play fine (but at nearly 10 minutes per song, when listening to them twice each, I haven't done many) I suspect the differences are due to some player in the past "enhancing" my collection by messing about with ID3 tags, but I can't be certain. Even if I identify differences in ID3 tags, I would like to confirm that no cosmic ray or file copy error issues have damaged any of the files. One method that occurs to be is finding the byte locations of the differences, and ignoring all changes in the first ~10kb of each file, but I don't know how to do this. I have on the order of a hundred or so files that differ across the directory tree. I found How to compare mp3, flac audio data in a file, ignoring header data (ID3 tag) etc.? -- but I can't run alldup due to being Linux only, and from the sounds of it, it would only partially solve my issues anyway.

    Read the article

  • Windows 7 64-bit installation from alternative media (no DVD/USB Flash drive)

    - by Niels Willems
    Greetings I currently have Windows 7 x86 installed on my computer. I want to install Windows 7 x64 on a different partition on my computer. However there is a little issue, I cannot run the x64 install from Windows 7 x86 which I currently have. I was planning to Install Windows 7 x64 on another partition to then boot up from that partition to install it on the partition I actually want my OS on. Once that is complete I could just format the partition from the Windows 7 x64 that I didn't need anymore. But the installer will not run from the x86 version of Windows 7 even though I do not want to upgrade that Windows directly. The reason I'm doing this in such a weird way is that my optical drive is broken and I'm really not into buying a new one since I would use it like once every year or so. I also don't have a USB Flash Drive which is big enough to hold the installation files. As far as I'm aware I cannot use an external hard drive such as this one, which I do have. Are there any alternatives in which I can install Windows 7 x64 or am I forced into buying a USB Flash Drive or new optical drive? Thank you in advance for your replies. Edit: This picture shows my current partitions on my laptop. I want to get Windows 7 x64 on the C partition but have to install it first on the F partition to then boot up the F partition windows to format C and install x64 on that one. My external drive is J. Edit 2: No alternative computer which has a DVD drive, install files are located on an iso from MA3D. To install my 32 bit version I mounted the ISO in Daemon Tools to replace my Windows Vista but since I cannot run 64 bit into my 32 bit OS this doesn't work.

    Read the article

  • SQL Server 2008 second instance times out when logging in -- but only the first time?

    - by Kromey
    This is a strange one that has plagued me for a while now. When logging in to the second instance of SQL Server 2008 on one of our database servers, we get a timeout error: Cannot connect to servername\mssqlserver2. Additional information: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. (Microsoft SQL Server)") (This is the error message when trying to connect with Microsoft SQL Server Management Studio; other tools experience the same error, but of course say it in different ways.) Immediately re-attempting to log in works just fine, so whatever the cause it's ephemeral! This happens regardless of user or authentication type (both Windows and SQL Server authentication methods are supported on this instance). What's even weirder, though, is that the first instance on this server has never once demonstrated this problem. Server is a Windows Server 2008 R2 virtual server, hosted in Microsoft Hyper-V (host is likewise Server 2008 R2). The server has 2GB of RAM, and seems to regularly be using 90% of that -- could low memory be the cause of this issue? I could see this second instance -- which is not used very often yet -- being swapped out to disk, and then taking too long to load back into memory to respond in time to the connection request, but I'd rather have more than just my own hunch before I go scheduling a downtime for this server (the first instance is used regularly) and then just throwing extra resources at it in the blind hope that the problem goes away.

    Read the article

  • Upgrade an Ubuntu 8.04 installation with VMware Server 1.0.8 and lots of guest OSes to Something Els

    - by Glyph
    I have an Ubuntu 8.04 (Hardy Heron) host machine which is running a whole slew of virtual machines in VMWare Server 1.0.8. Among other guest OSes, there is every release version of Ubuntu since 6.06, OpenSolaris 2009.06, and Windows XP. Right now I access these VMs from a variety of client OSes as well; Linux and Windows via the VMWare server console, and MacOS via X-forwarding the host machine's server console. I'd like to upgrade the host to Ubuntu 10.04 (Lucid Lynx), but from what I can tell, getting VMWare Server 1.x to work on a more recent version of Linux is a real pain. While VMware Server 2.x is a bit easier, it's still not packaged as Debian packages, so installing security updates is a big chore. As long as I'm upgrading anyway, I'd like to move to a virtualization solution that will allow me to automate applying updates. The options that I'm aware of right now are KVM (managed via virt-manager) and VirtualBox (as managed by its own tools or via its own libvirt bindings), but I'm open to other suggestions. For each option, I'd like to know how do I convert my guest images to the new format? am I going to have to re-activate my Windows guests (alternatively, "If the virtual hardware is different by default, can I avoid re-activation by changing some virtualization configuration to provide me with more similar virtual hardware") what are the management options like for each client OS (mac, linux, windows)? Thanks.

    Read the article

< Previous Page | 414 415 416 417 418 419 420 421 422 423 424 425  | Next Page >