Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 42/59 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• how to portforward port 7300 from server A to server B

  - by Patrick van Hout

  hi, We are using Stunnel. But want to replace it is with an iptables entry if possible. 192.168.123.122:7300 need to be forwarded to 192.168.123.188:7300. So in iptables I set these two entries: [root@dev ~]# iptables -t nat -A PREROUTING -p tcp --dport 7300 -j DNAT --to-destination 192.168.123.188:7300 [root@dev ~]# iptables -A FORWARD -m state -p tcp -d 192.168.123.188 --dport 7300 --state NEW,ESTABLISHED,RELATED -j ACCEPT But it isn't working. I did check that /proc/sys/net/ipv4/conf/eth0/forwarding has the value "1" inside. Any tips or hints? thanks, Patrick

  Read the article

• Heartbeat won't start up from a cold boot when a failed node is present

  - by Matthew

  I currently have two ubuntu servers running Heartbeat and DRBD. Let's say one node is down... The servers are directory connected with a 1000Mbps cross over cable on eth1 and have access to a IP camera LAN on eth0 The node that is still functioning won't start up heartbeat and provide access to the drbd resource. I have to manually restart heartbeat by "sudo service heartbeat restart" to get everything up and running. How can I get it to start fine from a cold start? Here is the my ha.cf and some material from the syslog... If I'm missing any information that might be of some help. http://pastebin.com/rGvzVSUq <--- Syslog http://pastebin.com/VqpaPSb5 <--- ha.cf

  Read the article

• Static Route Qestion

  - by mrlayance

  I have a Wan simulator between 2 networks. I can ping both networks from the wan simulator, but I can not ping from one network to the other. testr01 Fa0/0 10.0.0.1/24 FA0/1 192.168.0.1/30 | | Wan Sim 2 nics Eth0 192.168.0.2/30 | Eth1 192.168.1.2/30 | | testr02 Fa0/1 192.168.1.1/30 Fa0/0 10.1.0.2/24 I can not figure out what type of routes I need. On the route? On the Server? I guess all 10. traffic to the Fa0/0 ports? Thanks

  Read the article

• configure Heartbeat on Centos Linux - error message

  - by Elad Dotan

  I installed Heartbeat on my Centos Linux and it seems to partially work..but I'm trying to monitor a service with no success. only when I reboot the main server the backup server takes over. in the logs I get : heartbeat[30476]: 2012/03/20_18:51:57 WARN: string2msg_ll: node [node1] failed authentication heartbeat[30476]: 2012/03/20_18:51:58 WARN: string2msg_ll: node [node02] failed authentication the authkeys is identical (copied from one to another). this is my ha.cf: logfile /var/log/ha-log logfacility local0 keepalive 2 deadtime 30 initdead 120 bcast eth0 udpport 694 auto_failback on node server01.com node server02.com haresources : server01.com 38.108.117.3 aim chat any idea how to fix the problem so if a service stops the other server take over Thanks! E.

  Read the article

• Port based bandwidth shaping

  - by nixnotwin

  I have an interent connection with the speed of 4000k bits up and down. I want to do port based traffic shaping on a ubuntu machine, which acts as router. eth0 is the WAN interface. This is how I would like to allocate bandwidth: For ports 80 and 445 the bandwidth usage can go upto 90% For ports above 1024 upto 65535 the bandwidth usage can go upto 10% For remaining ports the bandwidth usage can go upto 40% The easiest way for achieving the above is using a router with tomato firmware. I have used it and it is very efficient. I want to try if it can be done on a Ubuntu or any GNU/Linux machine. I have googled extensively about the topic and I feel there isn't much information.

  Read the article

• ipfw to redirect traffic from port 80 and 443 to 8080

  - by user1048138

  -A PREROUTING -s 10.0.10.0/24 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 -A PREROUTING -s 10.0.10.0/24 -p tcp -m tcp --dport 443 -j REDIRECT --to-ports 8080 -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE The above code is what I have used on linux to forward my ports to 8080, how can I do the same on a mac? I have tried test_machine:~ root# ipfw show 00666 0 0 fwd 127.0.0.1,8080 tcp from any to me dst-port 80 and its not working! any suggestions?

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• How to set up a wireless AP with a linux box and SOCKS proxy

  - by user50455

  I've got: (1) Linux box (Arch linux to be precise, but that doesn't really matter) (2) Ethernet connection on it (say, eth0) (3) Socks proxy on a remote site (say, remote :port), which can be accessed through (2) (4) Wireless card on local linux box (say, eth1) So, the task is: create a wireless access point using (4) on local site (1) in such a way that all connections from it will go through proxy (3). E.g., when one simply connects to that AP (well, there should be DHCP or something for that) and goes to serverfault.com, all the traffic goes through that SOCKS proxy. I'm just asking for the digging direction and some references, not step-by-step tutorial. Thanks in advance

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• Apache reverse proxy, redirect requests based on IP addresses

  - by Mr Aleph

  I have a Linux box with 2 NICs. I installed and configured Apache 2 for reverse proxy. Each NIC has its own IP address and I was wondering if there is any way to redirect the requests via Apache based on the IP address that was used to get to the box. For example: eth0 has IP 100.100.100.100, eth1 has 200.200.200.200 If I browse to http://100.100.100.100/AppName/App I want it to redirect to 1.1.1.1 and if I browse to http://200.200.200.200/AppName/App I want it to go to 2.2.2.2 Right now the configuration for Apache is set as follow ProxyPass /AppName/App http://1.1.1.1/AppName/App ProxyPassReverse /AppName/App http://1.1.1.1/AppName/App So anything going to /AppName/App will be redirected to 1.1.1.1 I was reading something about ProxyHTMLURLMap but I don't know whether this is something that might help. Any idea how to do this? Thanks!

  Read the article

• Iptables mark incoming packet - vpn routing

  - by Tom

  I have connected my home to my workplace for out of house backup reasons through openvpn. The connection is working nicely. At work I have 5 fixed IP addresses. Now I would like to assign one of these IP addresses to be forwarded to my home machine. I have confirmed packet arrival at my home machine with tcpdump. The problem is that my default route at home is NOT the tun0 (naturally), but eth0 to my own ISP. So I created a separate routing table to route my tun0 packets back to where they belong, but do not how to mark the incoming packet which arrive through tun0 with iptables, so I can drive them back. I do not want any port restrictions, but only what comes from tun0 should leave through tun0 thanks tom

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• Monitor Bonded Interface for Disconnection

  - by bradlis7

  I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

  Read the article

• What can cause peaks in pagetables in /proc/meminfo ?

  - by Fuzzy76

  I have a gameserver running Debian Lenny on a VPS host. Even when experiencing a fairly low load, the players start experiencing major lag (ping times rise from 50 ms to 150-500 ms) in bursts of 3 - 10 seconds. I have installed Munin server monitoring, but when looking at the graphs it looks like the server has plenty of CPU, RAM and bandwidth available. The only weird thing I noticed is some peaks in the memory graph attributed to "page_tables" which maps to PageTables in /proc/meminfo but I can't find any good information on what this might mean. Any ideas what might be causing this? If you need any more graps, just let me know. The interrupts/second count is at roughly 400-600 during this period (nearly all from eth0). The drop in committed was caused by me trying to lower the allocated memory for the server from 512MB to 256MB, but that didn't seem to help.

  Read the article

• VirtualBox "Bridged Adapter" when host NIC is turned off

  - by chris_l

  Hi, I'm running Linux (Debian Etch) in a VirtualBox VM on my MacBook. I usually ssh from my Mac terminal to the guest machine. I also want to access the internet from my guest, so I set up my host's WLAN card (en1) as a bridged adapter for eth0 on the client. This works fine, but when I turn off the WLAN card (e.g. to reduce battery consumption), I'd still like to ssh from my host to the guest. This fails of course, because en1 loses its IP address. Is a bridged adapter the best option for what I want to do? How can I make it work? (A simple "ifconfig en1 add 10.0.0.4" didn't do the trick...) Thanks Chris

  Read the article

• Ubuntu VPN Server (PPTPD) Configuration - Pass Traffic to Internet

  - by SnAzBaZ

  I am trying to configure PPTPD on my Ubuntu box to pass all VPN traffic through to it's internet connection, so I essentially want it to work like a Proxy. I think the problem is that no default gateway is being assigned to my PPTP client (Windows 7). I can connect to the VPN fine, I get an IP address and DNS servers but no default gateway. Do I need to configure a specific option to tell the VPN server to forward all traffic it receives down it's eth0 port and out to the internet. Thanks!

  Read the article

• DLINK Dir-655 Sharing and connecting wirelessly

  - by CYREX

  I have a D-LINK DIR-655 and i wish to do the following: My PC is connected to the internet via eth0 (Wired) and it has a wireless card. I wish to connect to the DIR-655 Router and share my connection via the router but wirelessly. I do not want to connect via a cabled wired to the router. I want to connect to the router via wifi. After that i want to make the Router share the wireless connection am giving it to other PCs wirelessly. So the sharing and connecting in all PCs will be done via WiFi.

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the internet via Eth0. Has one wireless network adapter and one more ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration

  Read the article

• Win 7: Share internet connection via Ethernet and WiFi

  - by Anvaka

  I have the following configuration: Box 1. Running Win 7, connected to the Internet via Eth0. Has one wireless network adapter and one another ethernet adapter (say, Eth1). Box 2. Running Win XP, has one ethernet adapter. I'd like to share Internet connection of the Box 1 with Box 2 via cable and have box 1 also sharing the Internet with other wireless devices. I don't want to buy any additional hardware. Is it possible? PS: Sorry if I'm unclear. I merely know nothing about NAT and network administration.

  Read the article

• Get/Assign IP addresses assigned by the DHCP sever with DLink switches in between

  - by Ranjith Kumar

  In our office the setup is like we have a UBUNTU server with DHCP Server connected to all the PCS via 24 port and 8 port DLink switches. How can I find all the PCS(with client name, ip and mac address)in the network?? When I do "vi /var/lib/dhcp3/dhcpd.leases", I get all the ip addresses for the switches. I have used "arp-scan --interface=eth0 --localnet" to get all the IPs and MAC Addresses in my local network. I couldn't find any option to diplay client name. Also I would like to assign particular IP for a particular PC. I have done the changes in the dhcp.conf file but it is not working as they are not directly connected to DHCP-server(DLink switches in between). How can I assign IPs for PCs in this kind of setup. Thanks in advance

  Read the article

• ldirectord ipvsadm not show reals ip and not work wtih pacemaker and corosync

  - by miguer27

  first thanks for your time. I'm having a problem with ldirectord that I can not solve, I comment my situation: I have two nodes with pace maker and corosync and configure somes resources: root@ldap1:/home/mamartin# crm status Last updated: Tue Jun 3 12:58:30 2014 Last change: Tue Jun 3 12:23:47 2014 via cibadmin on ldap1 Stack: openais Current DC: ldap2 - partition with quorum Version: 1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff 2 Nodes configured, 2 expected votes 7 Resources configured. Online: [ ldap1 ldap2 ] Resource Group: IPV_LVS IPV_4 (ocf::heartbeat:IPaddr2): Started ldap1 IPV_6 (ocf::heartbeat:IPv6addr): Started ldap1 lvs (ocf::heartbeat:ldirectord): Started ldap1 Clone Set: clon_IPV_lo [IPV_lo] Started: [ ldap2 ] Stopped: [ IPV_lo:1 ] root@ldap1:/home/mamartin# crm configure show node ldap2 \ attributes standby="off" node ldap1 \ attributes standby="off" primitive IPV-lo_4 ocf:heartbeat:IPaddr \ params ip="192.168.1.10" cidr_netmask="32" nic="lo" \ op monitor interval="5s" primitive IPV-lo_6 ocf:heartbeat:IPv6addrLO \ params ipv6addr="[fc00:1::3]" cidr_netmask="64" \ op monitor interval="5s" primitive IPV_4 ocf:heartbeat:IPaddr2 \ params ip="192.168.1.10" nic="eth0" cidr_netmask="25" lvs_support="true" \ op monitor interval="5s" primitive IPV_6 ocf:heartbeat:IPv6addr \ params ipv6addr="[fc00:1::3]" nic="eth0" cidr_netmask="64" \ op monitor interval="5s" primitive lvs ocf:heartbeat:ldirectord \ params configfile="/etc/ldirectord.cf" \ op monitor interval="20" timeout="10" \ meta target-role="Started" group IPV_LVS IPV_4 IPV_6 lvs group IPV_lo IPV-lo_6 IPV-lo_4 clone clon_IPV_lo IPV_lo \ meta interleave="true" target-role="Started" location cli-prefer-IPV_LVS IPV_LVS \ rule $id="cli-prefer-rule-IPV_LVS" inf: #uname eq ldap1 colocation LVS_no_IPV_lo -inf: clon_IPV_lo IPV_LVS property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1401264327" rsc_defaults $id="rsc-options" \ resource-stickiness="1000" The problem is in the ipvsadm only show a one real IP, when i configured two now, show the ldirector.cf: root@ldap1:/home/mamartin# ipvsadm IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags - RemoteAddress:Port Forward Weight ActiveConn InActConn TCP ldap-maqueta.cica.es:ldap wrr - ldap2.cica.es:ldap Route 4 0 0 TCP [[fc00:1::3]]:ldap wrr - [[fc00:1::2]]:ldap Route 4 0 0 root@ldap1:/home/mamartin# cat /etc/ldirectord.cf checktimeout=10 checkinterval=2 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=yes #ipv4 virtual=192.168.1.10:389 real=192.168.1.11:389 gate 4 real=192.168.1.12:389 gate 4 scheduler=wrr protocol=tcp checktype=on #ipv6 virtual6=[[fc00:1::3]]:389 real6=[[fc00:1::1]]:389 gate 4 real6=[[fc00:1::2]]:389 gate 4 scheduler=wrr protocol=tcp checkport=389 checktype=on and in the logs I see nothing clear: root@ldap1:/home/mamartin# ldirectord -d /etc/ldirectord.cf start DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.11:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.11:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 0) DEBUG2: Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) DEBUG2: Disabled real server=on:tcp:192.168.1.12:389:::4:gate:\/: (virtual=tcp:192.168.1.10:389) DEBUG2: Checking on: Real servers are added without any checks DEBUG2: Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) DEBUG2: Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Running system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) Destination already exists root@ldap1:/home/mamartin# cat /var/log/ldirectord.log [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Quiescent real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 0) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.12:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t 192.168.1.10:389 -r 192.168.1.12:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: 192.168.1.12:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: 192.168.1.11:389 (tcp:192.168.1.10:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: 192.168.1.11:389 (192.168.1.10:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::2]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] system(/sbin/ipvsadm -a -t [[fc00:1::3]]:389 -r [[fc00:1::2]]:389 -g -w 4) failed: [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Added real server: [[fc00:1::2]]:389 ([[fc00:1::3]]:389) (Weight set to 4) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Resetting soft failure count: [[fc00:1::1]]:389 (tcp:[[fc00:1::3]]:389) [Tue Jun 3 09:39:29 2014|ldirectord.cf|19266] Restored real server: [[fc00:1::1]]:389 ([[fc00:1::3]]:389) (Weight set to 4) do not know if this is a bug or a configuration error, can anyone help? Regards.

  Read the article

• Can not run ifconfig like commands via browser

  - by savruk

  Problem is I cannot run "ifconfig" or similar commands via browser. Environment: Programming language : python Server : lighttpd(CGI) , running on busybox. Well machine is really small and so I am really restricted. Tried techniques: chown every script to root. But there is no differences. Why? Because lighttpd runs under another user, I mean not under root. As it is not root, when I try to run script from browser it always calls the python file with its uid. So it makes it impossible to run "ifconfig eth0 192.168.2.123" like commands via web browser. I get "ifconfig: SIOCSIFADDR: Permission denied" error. What can I do? I do not have any sudoers file, so cannot modify sudo command. Well, I don't even have "sudo" command :) Thanks for your help

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >