Search Results

Search found 1454 results on 59 pages for 'eth0'.

Page 49/59 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Can not connect to wireless on 12.04 with Intel WiFi Link 5100

  - by WiData

  I am having problem in connecting to wifi. I have dual boot (Windows 7 and Ubuntu 12.04) on my Dell Studio 15. I upgraded to 12.04 quite some time ago (at least one month) from 11.10. Everything was working fine till yesterday. Since yesterday I can see the list of available Wifi connection but does not connect to any or if connects (after hours of trying) then disconnects after few minutes. My wifi interface is Intel WiFi Link 5100 AGN. However the problem is on both Windows and Ubuntu. Here are outputs of some commands which may be useful for those interested in helping: ~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:22:19:fa:65:bb UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:794 errors:0 dropped:0 overruns:0 frame:0 TX packets:794 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:56280 (56.2 KB) TX bytes:56280 (56.2 KB) wlan0 Link encap:Ethernet HWaddr 00:22:fb:d2:fc:ce UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:239 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:53603 (53.6 KB) Here is the output for the command sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fb:d2:fc:ce width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-48-generic-pae firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:f8000000-f8001fff My kernel version is kernel version 3.2.0-48-generic-pae I also checked this post which was helpful. But I am not sure if what is the exact problem. Any suggestions will be helpful. Should I be changing the firmware/driver? Currently my /lib/firmware has following iwlwifi files /lib/firmware/iwlwifi-1000-5.ucode /lib/firmware/iwlwifi-5000-5.ucode /lib/firmware/iwlwifi-100-5.ucode /lib/firmware/iwlwifi-5150-2.ucode /lib/firmware/iwlwifi-105-6.ucode /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-135-6.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-2000-6.ucode /lib/firmware/iwlwifi-6000g2a-6.ucode /lib/firmware/iwlwifi-2030-6.ucode /lib/firmware/iwlwifi-6000g2b-6.ucode /lib/firmware/iwlwifi-3945-2.ucode /lib/firmware/iwlwifi-6050-5.ucode /lib/firmware/iwlwifi-4965-2.ucode Thanks a lot for the help.

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• Why am I getting a "network is unreachable" error on Ubuntu Server?

  - by jason328

  I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Ubuntu systematically losing wired connection

  - by Lukasz Baczynski

  I'm working on 11.10 for few recent days, everything was working perfect until today. Updated ubuntu (some certs were updates as far as i remember) and from this time, wired network stops working randomly and systematically. (All other pcs/macs work fine) From 192.168.0.9 icmp_seq=25 Destination Host Unreachable From 192.168.0.9 icmp_seq=26 Destination Host Unreachable From 192.168.0.9 icmp_seq=27 Destination Host Unreachable From 192.168.0.9 icmp_seq=28 Destination Host Unreachable From 192.168.0.9 icmp_seq=29 Destination Host Unreachable From 192.168.0.9 icmp_seq=30 Destination Host Unreachable From 192.168.0.9 icmp_seq=31 Destination Host Unreachable 64 bytes from 192.168.0.1: icmp_req=32 ttl=64 time=1003 ms 64 bytes from 192.168.0.1: icmp_req=33 ttl=64 time=0.496 ms 64 bytes from 192.168.0.1: icmp_req=34 ttl=64 time=0.576 ms 64 bytes from 192.168.0.1: icmp_req=35 ttl=64 time=0.522 ms 64 bytes from 192.168.0.1: icmp_req=36 ttl=64 time=0.624 ms 64 bytes from 192.168.0.1: icmp_req=37 ttl=64 time=0.625 ms 64 bytes from 192.168.0.1: icmp_req=38 ttl=64 time=0.555 ms It'll work for 20 seconds then it'll stop working for 10-30sec and so on. I've tried setting my router to give static IPs, it doesn't help. NOTHING has been changed since yesterday beside the package update... Here are other settings that may be useful: baka@baka-PC:~/Private/projects/wduk$ lspci -nnk | grep -iA2 net 06:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432] Kernel driver in use: r8169 baka@baka-PC:~/Private/projects/wduk$ ifconfig -a eth0 Link encap:Ethernet HWaddr **Removed MAC address** inet addr:192.168.0.9 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:fe0a:85b2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6400 errors:0 dropped:6400 overruns:0 frame:6400 TX packets:7085 errors:0 dropped:107 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4191983 (4.1 MB) TX bytes:886881 (886.8 KB) Interrupt:72 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2522 errors:0 dropped:0 overruns:0 frame:0 TX packets:2522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1070130 (1.0 MB) TX bytes:1070130 (1.0 MB) baka@baka-PC:~/Private/projects/wduk$ cat /etc/resolv.conf # Generated by NetworkManager nameserver 8.8.8.8 thanks for help

  Read the article

• New Oracles VM RAC template with support for oracle vm 3 built-in

  - by wcoekaer

  The RAC team did it again (thanks Saar!) - another awesome set of Oracle VM templates published and uploaded to My Oracle Support. You can find the main page here. What's special about the latest version of DeployCluster is that it integrates tightly with Oracle VM 3 manager. It basically is an Oracle VM frontend that helps start VMs, pass arguments down automatically and there is absolutely no need to log into the Oracle VM servers or the guests. Once it completes, you have an entire Oracle RAC database setup ready to go. Here's a short summary of the steps : Set up an Oracle VM 3 server pool Download the Oracle VM RAC template from oracle.com Import the template into Oracle VM using Oracle VM Manager repository - import Create a public and private network in Oracle VM Manager in the network tab Configure the template with the right public and private virtual networks Create a set of shared disks (physical or virtual) to assign to the VMs you want to create (for ASM/at least 5) Clone a set of VMs from the template (as many RAC nodes as you plan to configure) With Oracle VM 3.1 you can clone with a number so one clone command for, say 8 VMs is easy. Assign the shared devices/disks to the cloned VMs Create a netconfig.ini file on your manager node or a client where you plan to run DeployCluster This little text file just contains the IP addresses, hostnames etc for your cluster. It is a very simple small textfile. Run deploycluster.py with the VM names as argument Done. At this point, the tool will connect to Oracle VM Manager, start the VMs and configure each one, Configure the OS (Oracle Linux) Configure the disks with ASM Configure the clusterware (CRS) Configure ASM Create database instances on each node. Now you are ready to log in, and use your x node database cluster. x No need to download various products from various websites, click on trial licenses for the OS, go to a Virtual Machine store with sample and test versions only - this is production ready and supported. Software. Complete. example netconfig.ini : # Node specific information NODE1=racnode1 NODE1VIP=racnode1-vip NODE1PRIV=racnode1-priv NODE1IP=192.168.1.2 NODE1VIPIP=192.168.1.22 NODE1PRIVIP=10.0.0.22 NODE2=racnode2 NODE2VIP=racnode2-vip NODE2PRIV=racnode2-priv NODE2IP=192.168.1.3 NODE2VIPIP=192.168.1.23 NODE2PRIVIP=10.0.0.23 # Common data PUBADAP=eth0 PUBMASK=255.255.255.0 PUBGW=192.168.1.1 PRIVADAP=eth1 PRIVMASK=255.255.255.0 RACCLUSTERNAME=raccluster DOMAINNAME=mydomain.com DNSIP= # Device used to transfer network information to second node # in interview mode NETCONFIG_DEV=/dev/xvdc # 11gR2 specific data SCANNAME=racnode12-scan SCANIP=192.168.1.50

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• How to switch off wifi on startup or from the console

  - by mit

  I have installed ubuntu 10.04 on a laptop. Wifi is switched on by default on startup. I can disable it rightclicking the network manager icon in the gnome bar. How can I set it to have wifi switched off as default? Alternatively, how can I switch off wifi on the console? I tried already the rfkill command but it does not list any devices and it does not switch off wifi, I tried different parameters. This is a standard install of the Ubuntu 10.04 i386 Desktop Live CD on an IBM T40 Laptop. EDIT A: This is the output of some rfkill commands on my system, and it does not affect the wifi of the laptop: $ rfkill --help Usage: rfkill [options] command Options: --version show version (0.4) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: <idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm $ rfkill list $ rfkill list wifi $ rfkill list all $ rfkill list wlan $ sudo rfkill list all $ sudo rfkill block all $ sudo rfkill block wlan $ sudo rfkill block wifi $ EDIT B: Now I found out that sudo ifconfig eth1 down turns it off. And I can turn it on through the gnome network applet again. But the applet does not reflect the change from the commandline, it stills believes wifi is switched on. I have to switch it off and on again on the applet to switch it on again, when I switched it off from the console. Is there a better way? This is what the syslog looks like when I switch wireless off and on again from the network manager: NetworkManager: <info> (eth1): device state change: 3 -> 2 (reason 0) NetworkManager: <info> (eth1): deactivating device (reason: 0). NetworkManager: <info> Policy set '24' (eth0) as default for routing and DNS. NetworkManager: <info> (eth1): taking down device. avahi-daemon[660]: Withdrawing address record for fe80::202:8aff:feba:d798 on eth1. kernel: [ 971.472116] airo(eth1): cmd:3 status:7f03 rsp0:0 rsp1:0 rsp2:0 NetworkManager: <info> (eth1): bringing up device. NetworkManager: <info> (eth1): supplicant interface state: starting -> ready NetworkManager: <info> (eth1): device state change: 2 -> 3 (reason 42) avahi-daemon[660]: Registering new address record for fe80::202:8aff:feba:d798 on eth1.*. kernel: [ 965.512048] eth1: no IPv6 routers present

  Read the article

• Lubuntu wireless issue with Broadcom chipset

  - by Variant Web Solutions

  I'm a web dev that just started a new venture in buying wiped laptops in bulk and selling them at a low cost to lower income families that want a laptop that will simply preform and not become virus ridden and require constant maintenance, so naturally I opted for a linux distro and after some research, lubuntu was my top pick. I'm not a stranger to linux as all of my servers for my web dev business are linux, but I am however new to L/Ubuntu and I'm having some issues with both wifi (broadcom chipsets) on the 20 or so dells that I have right now, D800's, D810's and E5400's. Not sure if you can point me in a solid direction, I've scoured (and implemented) the suggestions on ask ubuntu and still coming up short. On one of the e5400's ( though they all seem to suffer the same errors) I got the following: [code]dell-latitude-e5400@dell-Latitude-E5400:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. dell-latitude-e5400@dell-Latitude-E5400:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 00:1f.5 IDE interface: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 2 port SATA Controller [IDE mode] (rev 02) 02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba) 02:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) 02:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21) 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5761e Gigabit Ethernet PCIe (rev 10) dell-latitude-e5400@dell-Latitude-E5400:~$ rfkill Usage: rfkill [options] command Options: --version show version (0.5-1ubuntu1 (Ubuntu)) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm nfc dell-latitude-e5400@dell-Latitude-E5400:~$ [/code]

  Read the article

• What are these errors when I try to "make" the driver of my wireless network?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme file say to use the "make" command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Duplicate ping response when running Ubuntu as virtual machine (VMWare)

  - by Stonerain

  I have the following setup: My router - 192.168.0.1 My host computer (Windows 7) - 192.168.0.3 And Ubuntu is running as virtual machine on the host. VMWare network settings is Bridged mode. I've modified Ubuntu network settings in /etc/netowrk/interfaces, set the following config: iface eth0 inet static address 192.168.0.220 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 Internet works correctly, I can install packages. But it gets weird if I try to ping something I get this: PING belpak.by (193.232.248.80) 56(84) bytes of data. From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded From 192.168.0.1 icmp_seq=1 Time to live exceeded 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=250 time=17.0 ms 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=249 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=248 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=247 time=17.0 ms (DUP! ) 64 bytes from belhost.by (193.232.248.80): icmp_seq=1 ttl=246 time=17.0 ms (DUP! ) ^CFrom 192.168.0.1 icmp_seq=2 Time to live exceeded --- belpak.by ping statistics --- 2 packets transmitted, 1 received, +4 duplicates, +6 errors, 50% packet loss, ti me 999ms rtt min/avg/max/mdev = 17.023/17.041/17.048/0.117 ms I think even more interesting are the results of pinging the router itself: stonerain@ubuntu:~$ ping 192.168.0.1 -c 1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. From 192.168.0.3: icmp_seq=1 Redirect Network(New nexthop: 192.168.0.1) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=254 time=6.64 ms --- 192.168.0.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 6.644/6.644/6.644/0.000 ms But if I set -c 2: ... 64 bytes from 192.168.0.1: icmp_seq=1 ttl=252 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=251 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=254 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=253 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=252 time=13.5 ms (DUP!) 64 bytes from 192.168.0.1: icmp_seq=1 ttl=251 time=13.5 ms (DUP!) From 192.168.0.3: icmp_seq=2 Redirect Network(New nexthop: 192.168.0.1) 64 bytes from 192.168.0.1: icmp_seq=2 ttl=254 time=7.87 ms --- 192.168.0.1 ping statistics --- 2 packets transmitted, 2 received, +256 duplicates, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 6.666/10.141/13.556/2.410 ms Pinging host machine on the other hand works absolutely correctly: no DUPs, no errors. What seems to be the problem and how can I fix it? Thank you.

  Read the article

• Toshiba wireless is blocked

  - by zorrillo

  I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

  Read the article

• 13.10 upgrade dropping wifi [on hold]

  - by Daryl

  Almost a complete newb here. After my last upgrade from 12.04 to 13.10 my wifi now randomly drops. The only way I can get a signal back is a shutdown and restart otherwise it shows no network is even available to connect to. Had no problems until the upgrade. Any help would be appreciated. H/W path Device Class Description ==================================================== system h8-1534 (H2N64AA#ABA) /0 bus 2AC8 /0/0 memory 64KiB BIOS /0/4 processor AMD FX(tm)-6200 Six-Core Processor /0/4/5 memory 288KiB L1 cache /0/4/6 memory 6MiB L2 cache /0/4/7 memory 8MiB L3 cache /0/d memory 10GiB System Memory /0/d/0 memory DIMM Synchronous [empty] /0/d/1 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/2 memory 2GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/3 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/100 bridge RD890 PCI to PCI bridge (external gfx0 port B) /0/100/0.2 generic RD990 I/O Memory Management Unit (IOMMU) /0/100/2 bridge RD890 PCI to PCI bridge (PCI express gpp port B) /0/100/2/0 display Turks PRO [Radeon HD 7570] /0/100/2/0.1 multimedia Turks/Whistler HDMI Audio [Radeon HD 6000 Series] /0/100/5 bridge RD890 PCI to PCI bridge (PCI express gpp port E) /0/100/5/0 bus TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller /0/100/11 storage SB7x0/SB8x0/SB9x0 SATA Controller [RAID5 mode] /0/100/12 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/12.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/13 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/13.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/14 bus SBx00 SMBus Controller /0/100/14.2 multimedia SBx00 Azalia (Intel HDA) /0/100/14.3 bridge SB7x0/SB8x0/SB9x0 LPC host controller /0/100/14.4 bridge SBx00 PCI to PCI Bridge /0/100/14.5 bus SB7x0/SB8x0/SB9x0 USB OHCI2 Controller /0/100/15 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) /0/100/15.1 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) /0/100/15.2 bridge SB900 PCI to PCI bridge (PCIE port 2) /0/100/15.2/0 wlan0 network RT3290 Wireless 802.11n 1T/1R PCIe /0/100/15.2/0.1 generic RT3290 Bluetooth /0/100/15.3 bridge SB900 PCI to PCI bridge (PCIE port 3) /0/100/15.3/0 eth0 network RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller /0/100/16 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/16.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/101 bridge Family 15h Processor Function 0 /0/102 bridge Family 15h Processor Function 1 /0/103 bridge Family 15h Processor Function 2 /0/104 bridge Family 15h Processor Function 3 /0/105 bridge Family 15h Processor Function 4 /0/106 bridge Family 15h Processor Function 5 /0/1 scsi0 storage /0/1/0.0.0 /dev/sda disk 1TB WDC WD1002FAEX-0 /0/1/0.0.0/1 volume 189MiB Windows FAT volume /0/1/0.0.0/2 /dev/sda2 volume 244MiB data partition /0/1/0.0.0/3 /dev/sda3 volume 931GiB LVM Physical Volume /0/2 scsi2 storage /0/2/0.0.0 /dev/cdrom disk DVD A DH16ACSHR /0/3 scsi6 storage /0/3/0.0.0 /dev/sdb disk SCSI Disk /0/3/0.0.1 /dev/sdc disk SCSI Disk /0/3/0.0.2 /dev/sdd disk SCSI Disk /0/3/0.0.3 /dev/sde disk MS/MS-Pro /0/3/0.0.3/0 /dev/sde disk /1 power Standard Efficiency I apologize for my newbness. I hope this is enough info for the hardware. Thanks Bruno for pointing out I needed to add more info. If I am lacking anything else please let me know and I'll post it.

  Read the article

• Can't access some websites using Ubuntu 13.10

  - by Adame Doe

  Something's wrong with Ubuntu. Since I've upgraded to 13.10, I can't access some websites for no apparent reason. I've tried everything imaginable to solve this problem : Made sure that MTUs are the same, Disabled IPv6 in both the network manager and used browsers, Deactivated my network keys, DMZed my computer, Used other DNS like Google and OpenDNS, Checked that no firewall was running my computer ... And it's the same result. I even tried to reinstall Ubuntu a couple of times, but no luck. The most annoying thing about it is I can't access wordpress.org! So, there's no way it could be an ISP restriction of some kind. When I use a VPN, I can access pretty much anything. I'm really frustrated because I have to use wordpress.org very often. Any clue? ifconfig adame@adame-ws:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:3d:b0:7c inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::226:18ff:fe3d:b07c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8024 errors:0 dropped:0 overruns:0 frame:0 TX packets:7966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:684480 (684.4 KB) TX bytes:616608 (616.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8222 errors:0 dropped:0 overruns:0 frame:0 TX packets:8222 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:568269 (568.2 KB) TX bytes:568269 (568.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:70:40:85:eb inet addr:192.168.2.3 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::219:70ff:fe40:85eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1464 Metric:1 RX packets:123705 errors:0 dropped:0 overruns:0 frame:0 TX packets:98141 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:94963545 (94.9 MB) TX bytes:10387470 (10.3 MB) /etc/hosts 127.0.0.1 localhost 127.0.1.1 adame-ws ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters tracepath wordpress.org 1: adame-ws.local 0.092ms pmtu 1500 1: 192.168.2.1 1.300ms asymm 2 1: 192.168.2.1 1.060ms asymm 2 2: no reply 3: no reply 4: no reply 5: no reply 6: no reply 7: no reply 8: no reply ... keep on going like that ping wordpress.org adame@adame-ws:~$ ping wordpress.org PING wordpress.org (66.155.40.250) 56(84) bytes of data. --- wordpress.org ping statistics --- 10 packets transmitted, 0 received, 100% packet loss, time 9071ms

  Read the article

• Operation times out trying to SSH outside LAN i.e. from internet to LAN no connection is established

  - by Pelle L

  I run Ubuntu 12.04 and have no success connecting with SSH from "Internet". The router is a TL-MR3420 which is set up to forward requests to one of the NIC's on ubuntu machine (which has in total 3 NICs). I can SSH from a client on the "local" network/LAN. The forward mechanism in the router seems to work. If I stop SSH service on the Ubuntu machine and instead start one on the windows machine - it works like a charm. I do not use the Std port 22 but that shouldn't be an issue as far as I understand - sine it works on the same port on the win machine. Since my public IS isn't static I use a dynDNS service but as said earlier the same setup works from the win machine. The router is located on 192.168.0.1 The Ubuntu NICs has the following IP: eth2 192.168.0.100 , eth1 192.168.0.101 , eth0 192.168.0.102 and I have forwarded the "outside" request to 192.168.0.100 In regards for firewall settings on the Ubuntu machine I have disabled the ufw and the command ufw status give status: inactive. I don't now it this is relevant information but teh command iptables --list give: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have tried to catch traffic with help of wireshark (a tool I'm not too used to use) and it seems as a few (3?) "requests" actually reaches the NIC but ... nothing happens. The syslog does not show any entries during these attempts. Perhaps it could be some routing issues but I have reached my level of competence and are stuck ... all help and support to get this sorted out is much appreciated. I'm new to Linux so please do not assume I have a configuration that is correct - but as I wrote earlier - if the client that initiate SSH is on the LAN it all works. PS:I have also tried to get VPN (PPP) working from Internet with no success - once again VPN works on the windows machine ... so my best guess is that this is related to how the ubuntu machine handles (IP) traffic and not the TL-MR3420 router or other network issues.

  Read the article

• WiFi on Ubuntu 12.04 custom: downloading unbearably slow

  - by Mark

  iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

  Read the article

• ignoring informational payload, type INVALID_COOKIE msgid=00000000

  - by user197279

  I'm configuring a site-to-site vpn between openswan ipsec and cisco asa 5540. After the step, i started ipesc service but the error i'm seeing is: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:30 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:42:51 pluto[11712]: "myVPN" #1: ignoring informational payload, type INVALID_COOKIE msgid=00000000 Nov 5 09:42:51 pluto[11712]: "myVPN" #1: received and ignored informational message Nov 5 09:43:30 pluto[11712]: "myVPN" #1: max number of retransmissions (2) reached STATE_MAIN_I2 Nov 5 09:43:30 pluto[11712]: "myVPN" #1: starting keying attempt 2 of at most 3 Any advise why I'm getting this error on openswan? Also sudo ipsec whack --status gives: "myVPN": 10.0.xx.0/24===10.0.7x.x[54.209.y.yyy,+S=C]---10.0.xx.x...10.0.70.x---41.22x.4.xx<41.22x.4.xx[+S=C]===41.22y.4.yyy/32; unrouted; eroute owner: #0 000 "myVPN": myip=54.209.zz.zz; hisip=unset; 000 "myVPN": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 3 000 "myVPN": policy: PSK+ENCRYPT+TUNNEL+DONTREKEY+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,32; interface: eth0; 000 "myVPN": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 "myVPN": IKE algorithms wanted: AES_CBC(7)_256-SHA1(2)_000-MODP1024(2); flags=-strict 000 "myVPN": IKE algorithms found: AES_CBC(7)_256-SHA1(2)_160-MODP1024(2) 000 "myVPN": ESP algorithms wanted: AES(12)_256-SHA1(2)_000; flags=-strict 000 "myVPN": ESP algorithms loaded: AES(12)_256-SHA1(2)_160 000 000 #5: "myVPN":500 STATE_MAIN_I2 (sent MI2, expecting MR2); EVENT_RETRANSMIT in 8s; nodpd; idle; import:admin initiate 000 #5: pending Phase 2 for "myVPN" replacing #0 Thanks.

  Read the article

• iptables -P FORWARD DROP makes port forwarding slow

  - by Isaac

  I have three computers, linked like this: box1 (ubuntu) box2 router & gateway (debian) box3 (opensuse) [10.0.1.1] ---- [10.0.1.18,10.0.2.18,10.0.3.18] ---- [10.0.3.15] | box4, www [10.0.2.1] Among other things I want box2 to do nat and port forwarding, so that I can do ssh -p 2223 box2 to reach box3. For this I have the following iptables script: #!/bin/bash # flush iptables -F INPUT iptables -F FORWARD iptables -F OUTPUT iptables -t nat -F PREROUTING iptables -t nat -F POSTROUTING iptables -t nat -F OUTPUT # default default_action=DROP for chain in INPUT OUTPUT;do iptables -P $chain $default_action done iptables -P FORWARD DROP # allow ssh to local computer allowed_ssh_clients="10.0.1.1 10.0.3.15" for ip in $allowed_ssh_clients;do iptables -A OUTPUT -p tcp --sport 22 -d $ip -j ACCEPT iptables -A INPUT -p tcp --dport 22 -s $ip -j ACCEPT done # allow DNS iptables -A OUTPUT -p udp --dport 53 -m state \ --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p udp --sport 53 -m state \ --state ESTABLISHED,RELATED -j ACCEPT # allow HTTP & HTTPS iptables -A OUTPUT -p tcp -m multiport --dports 80,443 -j ACCEPT iptables -A INPUT -p tcp -m multiport --sports 80,443 -j ACCEPT # # ROUTING # # allow routing echo 1 >/proc/sys/net/ipv4/ip_forward # nat iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # http iptables -A FORWARD -p tcp --dport 80 -j ACCEPT iptables -A FORWARD -p tcp --sport 80 -j ACCEPT # ssh redirect iptables -t nat -A PREROUTING -p tcp -i eth1 --dport 2223 -j DNAT \ --to-destination 10.0.3.15:22 iptables -A FORWARD -p tcp --sport 22 -j ACCEPT iptables -A FORWARD -p tcp --dport 22 -j ACCEPT iptables -A FORWARD -p tcp --sport 1024:65535 -j ACCEPT iptables -A FORWARD -p tcp --dport 1024:65535 -j ACCEPT iptables -I FORWARD -j LOG --log-prefix "iptables denied: " While this works, it takes about 10 seconds to get a password promt from my ssh command. Afterwards, the connection is as responsive as could be. If I change the default policy for my FORWARD chain to "ACCEPT", then the password promt is there imediatly. I have tried analysing the logs, but I can not spot a difference in the logs for ACCEPT/DROP in my FORWARD chain. Also I have tried allowing all the unprivileged ports, as box1 uses thoses for doing ssh to box2. Any hints? (If the whole setup seems strange to you - the point of the exercise is to understand iptables ;))

  Read the article

• Problem with switch dell 6224

  - by Matias

  Hello, we just have upgraded the firmware of a dell 6224 power connect switch and it won't reload. These are the symptons: - I power up the switch having the serial cable connected to it and the switch outputs nothing. The configuration of the serial console is fine: 9600 bds, etc... In fact, before the upgrade, I was connected to the switch through the very same cable. - Reseting the switch with its reset pinhole does not reset the switch: the power and fan lights powers off while I keep pressed the pinhole, but the switch itself does not resets. - When I connect an UTP cable to one of the switches port, the green lights don't flash, but ''mii-tool eth0'' in my laptop shows there is link!! The only thing I see in the output, different from other upgrades I've done, is this line at the end: Erasing Boot Flash.....^^^^Done. Any help or idea will be more than welcome!! Thanks!! console#show version Image Descriptions image1 : image2 : Images currently available on Flash -------------------------------------------------------------------- unit image1 image2 current-active next-active 1 <none> 3.0.0.8 image2 image2 console#boot system image2 Activating image image2 .. console#update bootcode Update bootcode and reset (Y/N)? Updating boot code ... Extracting boot code from image... Erasing Boot Flash.....^^^^Done.

  Read the article

• Bridging Virtual Networking into Real LAN on a OpenNebula Cluster

  - by user101012

  I'm running Open Nebula with 1 Cluster Controller and 3 Nodes. I registered the nodes at the front-end controller and I can start an Ubuntu virtual machine on one of the nodes. However from my network I cannot ping the virtual machine. I am not quite sure if I have set up the virtual machine correctly. The Nodes all have a br0 interfaces which is bridged with eth0. The IP Address is in the 192.168.1.x range. The Template file I used for the vmnet is: NAME = "VM LAN" TYPE = RANGED BRIDGE = br0 # Replace br0 with the bridge interface from the cluster nodes NETWORK_ADDRESS = 192.168.1.128 # Replace with corresponding IP address NETWORK_SIZE = 126 NETMASK = 255.255.255.0 GATEWAY = 192.168.1.1 NS = 192.168.1.1 However, I cannot reach any of the virtual machines even though sunstone says that the virtual machine is running and onevm list also states that the vm is running. It might be helpful to know that we are using KVM as a hypervisor and I am not quite sure if the virbr0 interface which was automatically created when installing KVM might be a problem.

  Read the article

• Why the system information message when accessing an Ubuntu server doesn't match free -m?

  - by Andres

  Each time I SSH into my AWS Ubuntu servers I see a system information message, showing load, memory usage and packages available to install, like this: Welcome to Ubuntu 12.04.3 LTS (GNU/Linux 3.2.0-51-virtual x86_64) * Documentation: https://help.ubuntu.com/ System information as of Sun Nov 10 18:06:43 EST 2013 System load: 0.08 Processes: 127 Usage of /: 4.9% of 98.43GB Users logged in: 1 Memory usage: 69% IP address for eth0: 10.236.136.233 Swap usage: 100% Graph this data and manage this system at https://landscape.canonical.com/ 13 packages can be updated. 0 updates are security updates. Get cloud support with Ubuntu Advantage Cloud Guest http://www.ubuntu.com/business/services/cloud Use Juju to deploy your cloud instances and workloads. https://juju.ubuntu.com/#cloud-precise *** /dev/xvda1 will be checked for errors at next reboot *** *** System restart required *** My question is about the memory percentage shown. In this case, it's showing a 69% of memory usage, but since the swap usage was 100% I checked it by myself. So when I run free -m I get this: total used free shared buffers cached Mem: 1652 1635 17 0 4 29 -/+ buffers/cache: 1601 51 Swap: 895 895 0 And that's of course closer to 100% than to 69%

  Read the article

• Xen HVM networking wont work

  - by Nathan

  I'm trying to get a Xen HVM network working using route however I am failing. Xen PV works fine using Ubuntu but when installing Ubuntu on HVM it fails to pick up the network. I'll let you know now that I'm not that experienced with Xen so I would appreciate any help. vm104 is the HVM thats causing me the problems, here is the configs that I believe should help resolve the problem. [root@eros vm104]# cat vm104.cfg import os, re arch = os.uname()[4] if re.search('64', arch): arch_libdir = 'lib64' else: arch_libdir = 'lib' kernel = '/usr/lib/xen/boot/hvmloader' builder = 'hvm' memory = 6000 shadow_memory = '8' cpu_weight = 256 name = 'vm104' vif = ['type=ioemu, ip=85.25.x.y, vifname=vifvm104.0, mac=00:16:3e:52:3d:fe, bridge=xenbr0'] acpi = 1 apic = 1 vnc = 1 vcpus = 4 vncdisplay = 3 vncviewer = 0 vncconsole = 1 vnclisten = '217.118.x.y' vncpasswd = 'kCfb5S4tE7' serial = 'pty' disk = ['phy:/dev/vpsvg/vm104_img,hda,w', 'file:/home/solusvm/xen/iso/Windows-Server-2008-RC2.iso,hdc:cdrom,r'] device_model = '/usr/' + arch_libdir + '/xen/bin/qemu-dm' boot = 'cd' sdl = '0' usbdevice = 'tablet' pae=1 [root@eros /]# cat /etc/xen/xend-config.sxp | egrep -v "(^#.*|^$)" (xend-unix-server yes) (xend-unix-path /var/lib/xend/xend-socket) (xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$') (network-script network-route) (vif-script vif-route) (network-script 'network-route netdev=eth0') (dom0-min-mem 256) (dom0-cpus 0) (vnc-listen '0.0.0.0') (vncpasswd '') (keymap 'en-us') The Windows install will not pick up the network - I've tried setting the IP manually by using the Xen servers IP as the gateway and setting the main IP in Windows but no luck. If anyone needs any more information let me know and I appreciate any input!

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• snort with barnyard2 not working on Fedora 12

  - by aHunter

  Has anyone come across this error with barnyard2 and snort? --== Initializing Barnyard2 ==-- Initializing Input Plugins! Initializing Output Plugins! Parsing config file "/etc/snort/barnyard2.conf" Log directory = /var/log/barnyard2 database: compiled support for (mysql) database: configured to use mysql database: schema version = 107 database: host = localhost database: user = test database: database name = snort database: sensor name = localhost:eth0 database: sensor id = 1 database: data encoding = hex database: detail level = full database: ignore_bpf = no database: using the "log" facility --== Initialization Complete ==-- ______ -*> Barnyard2 <*- / ,,_ \ Version 2.1.8 (Build 251) |o" )~| By the SecurixLive.com Team: http://www.securixlive.com/about.php + '''' + (C) Copyright 2008-2010 SecurixLive. Snort by Martin Roesch & The Snort Team: http://www.snort.org/team.html (C) Copyright 1998-2007 Sourcefire Inc., et al. WARNING: Ignoring corrupt/truncated waldofile '/var/log/snort/barnyard.waldo' Opened spool file '/var/log/snort/snort.log.1282004944' ERROR: Unknown record type read: 104 Fatal Error, Quitting.. Snort seems to be working correctly as I have managed to get logs via syslog but when I try to use the barnyard config via Unified2 it is not working. Presumably because of the above error. Thanks in advance.

  Read the article

• Unable to connect to EC2 instance after "reboot"

  - by KPL

  I am not able to connect to my m1.small instance after rebooting it. I have already associated the public IP with this instance. Upon checking the system log, this seems to be the issue: cloud-init-nonethttp://11.84: waiting 10 seconds for network device cloud-init-nonethttp://21.85: waiting 120 seconds for network device cloud-init-nonethttp://141.85: gave up waiting for a network device. Cloud-init v. 0.7.3 running 'init' at Sun, 18 May 2014 07:02:55 +0000. Up 142.54 seconds. ci-info: +++++++++++++++++++++++Net device info++++++++++++++++++++++++ ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | Device | Up | Address | Mask | Hw-Address | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | lo | True | 127.0.0.1 | 255.0.0.0 | . | ci-info: | eth0 | False | . | . | 02:43:xx:xx:xx:xx | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Route info failed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! A bunch of these follow the above message: 2014-05-18 07:02:56,178 - url_helper.pyWARNING: Calling http://169.254.169.254/2009-04-04/meta-data/instance-id failed 0/120s: request error [HTTPConnectionPool(host='169.254.169.254', port=80): Max retries exceeded with url: /2009-04-04/meta-data/instance-id (Caused by : Errno 101] Network is unreachable) This is obviously related to the network interface not being working correctly. I have tried this so far: Relaunch a new instance from the custom AMI (created from EBS) of the failing instance. The same error shows up in the logs. Attach a new network interface to the EC2 instance. The error still persists. eth1 shows up in the list but the "up" column is False.

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >