Search Results

Search found 3691 results on 148 pages for 'perfect forwarding'.

Page 42/148 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

  • HP to Cisco spanning tree root flapping

    - by Tim Brigham
    Per a recent question I recently configured both my HP (2x 2900) and Cisco (1x 3750) hardware to use MSTP for interoperability. I thought this was functional until I applied the change to the third device (HP switch 1 below) at which time the spanning tree root started flapping causing performance issues (5% packet loss) between my two HP switches. I'm not sure why. HP Switch 1 A4 connected to Cisco 1/0/1. HP Switch 2 B2 connected to Cisco 2/0/1. HP Switch 1 A2 connected to HP Switch 2 A1. I'd prefer the Cisco stack to act as the root. EDIT: There is one specific line - 'spanning-tree 1 path-cost 500000' in the HP switch 2 that I didn't add and was preexisting. I'm not sure if it could have the kind of impact that I'm describing. I'm more a security and monitoring guy then networking. EDIT 2: I'm starting to believe the problem lies in the fact that the value for my MST 0 instance on the Cisco is still at the default 32768. I worked up a diagram: This is based on every show command I could find for STP. I'll make this change after hours and see if it helps. Cisco 3750 Config: version 12.2 spanning-tree mode mst spanning-tree extend system-id spanning-tree mst configuration name mstp revision 1 instance 1 vlan 1, 40, 70, 100, 250 spanning-tree mst 1 priority 0 vlan internal allocation policy ascending interface TenGigabitEthernet1/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface TenGigabitEthernet2/1/1 switchport trunk encapsulation dot1q switchport mode trunk ! interface Vlan1 no ip address ! interface Vlan100 ip address 192.168.100.253 255.255.255.0 ! Cisco 3750 show spanning tree: show spanning-tree MST0 Spanning tree enabled protocol mstp Root ID Priority 32768 Address 0004.ea84.5f80 Cost 200000 Port 53 (TenGigabitEthernet1/1/1) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32768 (priority 32768 sys-id-ext 0) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Root FWD 2000 128.53 P2p MST1 Spanning tree enabled protocol mstp Root ID Priority 1 Address a44c.11a6.7c80 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 1 (priority 0 sys-id-ext 1) Address a44c.11a6.7c80 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Te1/1/1 Desg FWD 2000 128.53 P2p Cisco 3750 show logging: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up HP Switch 1: ; J9049A Configuration Editor; Created on release #T.13.71 vlan 1 name "DEFAULT_VLAN" untagged 1-8,10,13-16,18-23,A1-A4 ip address 100.100.100.17 255.255.255.0 no untagged 9,11-12,17,24 exit vlan 100 name "192.168.100" untagged 9,11-12,17,24 tagged 1-8,10,13-16,18-23,A1-A4 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A4 no ip address exit vlan 40 name "Cafe" tagged 1,4,7,A1-A4 no ip address exit vlan 250 name "Firewall" tagged 1,4,7,A1-A4 no ip address exit vlan 70 name "DMZ" tagged 1,4,7-8,13,A1-A4 no ip address exit spanning-tree spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 password manager password operator HP Switch 1 show spanning tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0021f7-126580 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 363,490 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : 1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 0 IST Remaining Hops : 20 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 | Auto 128 Disabled | A2 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A3 10GbE-CX4 | Auto 128 Disabled | A4 10GbE-SR | Auto 128 Disabled | HP Switch 1 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00842 stp: MSTI 1 starved for an MSTI Msg Rx on port A4 from 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to 32768:0021f7-126580 00839 stp: MSTI 1 Root changed from 32768:0021f7-126580 to 0:a44c11-a67c80 00839 stp: MSTI 1 Root changed from 0:a44c11-a67c80 to ... HP Switch 2 Configuration: ; J9146A Configuration Editor; Created on release #W.14.49 vlan 1 name "DEFAULT_VLAN" untagged 1,3-17,21-24,A1-A2,B2 ip address 100.100.100.36 255.255.255.0 no untagged 2,18-20,B1 exit vlan 100 name "192.168.100" untagged 2,18-20 tagged 1,3-17,21-24,A1-A2,B1-B2 no ip address exit vlan 21 name "Users_2" tagged 1,A1-A2,B2 no ip address exit vlan 40 name "Cafe" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 250 name "Firewall" tagged 1,13-14,16,A1-A2,B2 no ip address exit vlan 70 name "DMZ" tagged 1,13-14,16,A1-A2,B2 no ip address exit logging 192.168.100.18 spanning-tree spanning-tree 1 path-cost 500000 spanning-tree config-name "mstp" spanning-tree config-revision 1 spanning-tree instance 1 vlan 1 40 70 100 250 HP Switch 2 Spanning Tree: show spanning-tree Multiple Spanning Tree (MST) Information STP Enabled : Yes Force Version : MSTP-operation IST Mapped VLANs : 2-39,41-69,71-99,101-249,251-4094 Switch MAC Address : 0024a8-cd6000 Switch Priority : 32768 Max Age : 20 Max Hops : 20 Forward Delay : 15 Topology Change Count : 21,793 Time Since Last Change : 14 hours CST Root MAC Address : 0004ea-845f80 CST Root Priority : 32768 CST Root Path Cost : 200000 CST Root Port : A1 IST Regional Root MAC Address : 0021f7-126580 IST Regional Root Priority : 32768 IST Regional Root Path Cost : 2000 IST Remaining Hops : 19 Root Guard Ports : TCN Guard Ports : BPDU Protected Ports : BPDU Filtered Ports : PVST Protected Ports : PVST Filtered Ports : | Prio | Designated Hello Port Type | Cost rity State | Bridge Time PtP Edge ----- --------- + --------- ---- ---------- + ------------- ---- --- ---- A1 10GbE-CX4 | 2000 128 Forwarding | 0021f7-126580 2 Yes No A2 10GbE-CX4 | Auto 128 Disabled | B1 SFP+SR | 2000 128 Forwarding | 0024a8-cd6000 2 Yes No B2 | Auto 128 Disabled | HP Switch 2 Logging: I removed the date / time fields since they are inaccurate (no NTP configured on these switches) 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80 00839 stp: IST Root changed from 32768:0021f7-126580 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0004ea-845f80 00839 stp: CST Root changed from 32768:0004ea-845f80 to 32768:0024a8-cd6000 00435 ports: port B1 is Blocked by STP 00839 stp: CST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: IST Root changed from 32768:0024a8-cd6000 to 32768:0021f7-126580 00839 stp: CST Root changed from 32768:0021f7-126580 to 32768:0004ea-845f80

    Read the article

  • Where to set catch-all address in Postfix (virtual mailboxes in affect)

    - by Cem
    I successfully configured Postfix to deliver messages to virtual mailboxes. I can set aliases and pipes inside /etc/postfix/virtual and mailboxes inside /etc/postfix/virtual_mailbox files. However, whenever I set a catch-all domain and point to a remote email address, it overrides all other virtual mailboxes and virtual aliases set in postfix. How can I set a catch-all forwarding to the remote email address when virtual mailbox is enabled? I set catch-all like this: @mydomain.com [email protected] Thanks for your help!

    Read the article

  • Using OpenVPN, yet netflix.com blocks access

    - by user837848
    I have set up an OpenVPN server on a VPS in the USA and configured it to route all clients traffic through it. Everything seems to work fine regarding the VPN connection in gerneral. All ip lookup sites show me the us server's ip address and even hulu.com works(it won't work if you are not in the usa). But for some reason netflix.com says "Sorry, Netflix is not available in your country yet.". So I thought that netflix probably uses some more sophisticated ways to determine your location beyond just your ip address. But I could not find a way to get it to work until I dropped the idea of using a VPN and instead connected to the server via a simple socks tunnel with ssh by running: ssh -D 9999 user@serverip All I had to do was changing the key network.proxy.socks_remote_dns in Firefox from false to true to prevent DNS leaks and setting up the socks proxy. Then I could finally watch netflix.com. As a result I concluded that there is nothing in the browser(or something like system timezone) that tells netflix the location, so it has to have something to do with the OpenVPN config. After that I used tcpdump to log all the traffic on the server's network interface venet0 (OpenVZ VPS), visited netflix.com on the client while first connected to the VPN and then connected via socks tunnel and afterwards compared both outputs. The only thing that caught my eye was that while using the socks tunnel the server mainly used ipv6 to connect to netflix whereas it only used ipv4 when the client was connected to the OpenVPN server. But I don't get how that could make such a difference. So what am I missing? Is there a way to configure OpenVPN to also use ipv6 to connect to a website although there is only an ipv4 connection between the VPS and the client? Here is the server.conf of the OpenVPN server (OpenVZ VPS) local serverip port 443 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/vps1.crt key ./easy-rsa2/keys/vps1.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" client-to-client keepalive 10 120 tls-auth ta.key 0 # This file is secret cipher AES-256-CBC comp-lzo max-clients 4 user nobody group nogroup persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 3 iptables forwarding iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j SNAT --to-source serverip (enabled ipv4 forwarding) I have tried everything always on a Win7 and a Debian client with only ipv4 connections and always made sure that they use the correct DNS server (tested with ipleak.net and tcpdump / wireshark). client.conf: client dev tun proto tcp remote serverip 443 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 cipher AES-256-CBC comb-lzo verb 3

    Read the article

  • What are some of the best wireless routers for a price-conscious home power-user?

    - by Alain
    I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

    Read the article

  • MSMQ Resilience

    - by Paddy Carroll
    I have a requirement for a resilient MSMQ setup on VMWare ESX5. I am aware that we cannot allow the queue storage to be shared as it must be installed on physical disk mount, e.g. it cant be an CIFS or DFS Share. The following constraints apply: We don't use windows clustering We dont't rely on hot standbys Is there a way I can replicate the queue storage to another platform so that it can assume MSMQ duties on failure of the primary platforms using any method including queue forwarding?

    Read the article

  • Creating an ad-hoc wireles network on a router

    - by bo7ons
    My router is a Wag200g with openwag firmware. My laptop is connected to the university's internet through an ethernet cable and i have to set the browser proxy settings to connect. I want to create an ad-hoc network with a router so that i can let my laptop do the proxy routing/forwarding itself and that my android phone can connect to it and use my university's proxy (I've tried setting the proxy on my phone but it wont work).. Or am i approaching this the wrong way?

    Read the article

  • Router with Wake On LAN

    - by Jaroslav Záruba
    I'm looking for a new WiFi router, and one key feature for me is WOL. Seems like many routers won't do this w/ factory firmware. Given my last router (Asus WL-520g) turned into a disco-brick couple hours after flashed DD-WRT I'd prefer if the new one supported WOL (Wake on LAN) out of the box. Other required features would be: DynDNS service support Port forwarding NAT loopback so I can access services running in my own network using dyndns hostname or public IP w/o getting too old (for example DIR-615 with factory firmware lets you wait literally minutes)

    Read the article

  • Link aggregation with freebsd8 and a cicso 3550, what am i doing wrong?

    - by Flamewires
    Hey, I am trying to setup Link Aggrigation with LACP (well, anything that provides increased bandwidth and failover using my setup will work). I'm running FreeBSD 8.0 on 3 machines. M1 is running 2 10/100 ethernetcards setup for link aggrigation using lagg. for reference: ifconfig em0 up ifconfig tx0 up ifconfig create lagg0 ifconfig lagg0 laggproto lacp laggport tx0 laggport em0 192.168.1.16 netmask 255.255.255.0 I plugged them into ports 1 and 2 of a Cicso 3550. then ran: configure terminal interface range Fa0/1 - 2 switchport mode access switchport access vlan 1 channel-group 1 mode active (everythings in vlan 1) Now Im able to connect the other computers to other ports on the switch and failover works great, i can unplug cables in the middle of a transfer and the traffic gets rerouted. However, im not noticing any speed increase. My test setup: load balancing: i tried dst and src on the switch, neither seemed to give me a speed increase. I am SCPing 2 500 meg files from the lagg computer to other computers (one each) which are also running 10/100 full duplex cards. I get transfer speeds of about 11.2-11.4 Mbps to a single host, and about half that (5.9-6.2) Mbps when transferring to both at the same time. From what I understood with destination load balancing the router was suppose to balance traffic headed for 1 computer over 1 port and traffic headed for another over a diff(in this case) the other port. With destination-MAC address forwarding, when packets are forwarded to an EtherChannel, the packets are distributed across the ports in the channel based on the destination host MAC address of the incoming packet. Therefore, packets to the same destination are forwarded over the same port, and packets to a different destination are sent on a different port in the channel. For the 3550 series switch, when source-MAC address forwarding is used, load distribution based on the source and destination IP address is also enabled for routed IP traffic. All routed IP traffic chooses a port based on the source and destination IP address. Packets between two IP hosts always use the same port in the channel, and traffic between any other pair of hosts can use a different port in the channel. (Link) What am i doing wrong/what would i need to do to see a speed increase beyond what i could do with just a single card?

    Read the article

  • Custom DHCP Server on home network

    - by DanSpd
    Hello I have a computer network at my house which consists of two computers and one server. I have a software on dedicated server which requires direct connection to internet (port forwarding doesn't work for this). So I plan to setup network in following way. link text Please let me know if this will work. How good or bad could this be? Internet Connection: Verizon Fios 25/25

    Read the article

  • Custom DHCP Server on home network

    - by DanSpd
    Hello I have a computer network at my house which consists of two computers and one server. I have a software on dedicated server which requires direct connection to internet (port forwarding doesn't work for this). So I plan to setup network in following way. link text Please let me know if this will work. How good or bad could this be? Internet Connection: Verizon Fios 25/25

    Read the article

  • Can't port forward ssh on Asus RT-NU56 wireless router

    - by Matt
    I cannot ssh in (using putty) when I use 10.0.1.31 as the address. database server - wired switch part of Asus wireless router - office LAN So basically, we want to ssh in to the database server from our computer on the wired office LAN. Asus router has an ip of 10.0.1.31 and database server has a static IP of 192.168.0.20 I set up port forwarding like this: ssh 22 192.168.0.20 22 BOTH Firewall is turned completely off. Any other settings I'm missing?

    Read the article

  • Lenovo remote control media redirect

    - by Braithwaite Patrick Sean
    On a lenovo ThinkServer RD240 running firmware 1.20 with the latest BNC software, using the remote console to redirect a CD-ROM fails with the error: "CD-ROM redirection is not supported on this platform". Similar error for forwarding an iso image, foppy and USB drive. I tried executing the management console from Ubuntu, Windows 7 and OS X with the exact same error. The question is: What platform does the jViewer console support any kind of media redirection?

    Read the article

  • Cannot connect to WEBrick on home network

    - by Chris Stewart
    I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

    Read the article

  • Use same url externally as internally

    - by Nifle
    If I have a web server on my home network I can connect to it from work with http://my.external.ip/whatever/ (assuming NAT and forwarding). Naturally I have a bookmark in my browser that points to http://my.external.ip/whatever/ however when I use that bookmark on my home computer (also behind NAT) the link does not work because my firewall blocks it. (firewall is a old'ish Dlink) What is the best way to fix this issue?

    Read the article

  • Connect to remote MySQL using proxy

    - by hypeflow
    I'm trying to connect to a remote MySQL server (with TCP access limited to a specific IP) using port forwarding via SSH, but still haven't figured out how to do it. Here's what I intend to do: Local[A] ---> Proxy[B] ---> Remote MySQL[C] [A] Local machine with Windows [B] CentOS machine with IP 123.123.123.1 (with it's own MySQL running, btw) [C] Remote MySQL server with IP 123.123.123.1 authorized on port 3306 How to achieve this? Thanks in advance.

    Read the article

  • How to configure fetchmail to send messages from remote smtp server to Gmail?

    - by ifesdjeen
    I've been trying to setup email forwarding through fetchmail from remote smtp server to Gmail account, although messages are constantly coming to my local address and accessible via "mail" command. SMTP connection works perfectly, but emails do not go anywhere. System: debian, fetchmail Config: poll smtp.server protocol imap username “user” password “pass” smtpname “[email protected]” ssl Thank you!

    Read the article

  • Providing a static IP for resources behind AWS Elastic Load Balancer (ELB)

    - by tharrison
    I need a static IP address that handles SSL traffic from a known source (a partner). Our servers are behind an AWS Elastic Load Balancer (ELB), which cannot provide a static IP address; many threads about this here. My thought is to create an instance in EC2 whose sole purpose in life is to be a reverse proxy server having it's own IP address; accepting HTTPS requests and forwarding them to the load balancer. Are there better solutions?

    Read the article

  • Routing domain over lan [closed]

    - by Buri
    I have server on my local network which is exposed to the internet. I have domain pointed on my IP and setup forwarding. The thing i would like to do is when i access example.com from lan to connection be routed directly on my server, not to the nearest DNS. Things I had in mind were to upgrade router with dd-wrt and setup routing rule, or to setup local DNS. Unfortunately, I'm not familiar with neither of those systems.

    Read the article

  • How do I activate my gizmo5 phone number in Google Voice? [closed]

    - by Sorin Sbarnea
    I wasn't able to activate my gizmo5 number because Google Voice activation(verification) requires you to enter two dial tones (DTMF) and they did not work at least not with these two variants: Using gizmo5 PC client using fring from Iphone as gizmo5 SIP client Redirecting gizmo5 to a US mobile number None of the above methods worked for me. Any ideas? More info: http://www.google.com/support/forum/p/voice/thread?tid=1d8c1d99721e3509&hl=en http://googlevoices.blogspot.com/2009/04/forwarding-sip-calls-to-google-voice.html

    Read the article

  • Secure copy uucp style

    - by Alexander Janssen
    I often have the case that I have to make a lot of hops to the remote host, just because there is no direct routing between my client and the remote host. When I need to copy files from a remote host two or more hops away, I always have to: client$ ssh host1 host1$ ssh host2 host2$ scp host3:/myfile . host2$ exit host1$ scp host2:myfile . host1$ exit client$ scp host1:myfile . Back when uucp still was being used this would be as simple as a uucp host1!host2!host3 /myfile . I know that there's uucp over ssh, but unfortunately I don't have the proper privileges on those machines to set it up. Also, I'm not sure if I really want to fiddle around with customer's machines. Does anyone know of a method doing this tasks without the need to setup a lot of tunnels or deploying new software to remote hosts? Maybe some kind of recursive script which clones itself to all the remote hosts, doing the hard work for me? Assume that authentication takes place with public keys and that all hosts do SSH Agent Forwarding. Edit: I'm not looking for a way to automatically forwarding my interactive sesssion to the nexthop host. I want a solution to copy files bangpath-style using scp via multiple hops without the need to install uucp on any of those machines. I don't have the (legal) rights or the privileges to make permanent changes to the ssh-config. Also, I'm sharing this username and hosts with a lot of other people. I'm willing to hack up my own script, but I wanted to know if anyone knows something which already does it. Minimum-invasive changes to hosts on the bangpath, simple invocation from the client. Edit 2: To give you an impression of how it's properly been done in interactive sessions, have a look at the GXPC clustershell. This is basically a Python-script, which spwans itself over to all remote hosts which have connectivity and where your ssh-key is installed. The great thing about it is, that you can tell "I can reach HostC via HostB via HostA." It just works. I want to have this for scp.

    Read the article

  • How to configure fetchmail to send messages from remote smtp server to Gmail?

    - by ifesdjeen
    Hi, I've been trying to setup email forwarding through fetchmail from remote smtp server to Gmail account, although messages are constantly coming to my local address and accessible via "mail" command. SMTP connection works perfectly, but emails do not go anywhere. System: debian, fetchmail Config: poll smtp.server protocol imap username “user” password “pass” smtpname “[email protected]” ssl Thank you!

    Read the article

  • Cisco 1841 and routing /29 address

    - by Jonathan
    Could someone please explain in general terms how I'd configure a Cisco 1841 (2x ethernet ports) to route a public /29 address block (6 hosts) to my internal network. I wish to give the Cisco router one public IP and then several of my internal Windows servers will receive the other public IP addresses. Other hosts behind the router will access Internet via NAT. I'm a bit confused as I've only ever setup routers/firewalls that had a single public IP address with NAT and port forwarding to internal servers.

    Read the article

  • How to configure three IP address into single server

    - by user1363308
    I have Cisco device for call forwarding and three different system,I want to configure 15 and 16 server IP into 192.168.53.197 means eth0 --> 192.168.53.197 eth1 --> 192.168.16.15 eth2 --> 192.168.16.16 which work i have done with 15 and 16 individual , I will do some work on 197 after configuration eth1 and eth2. Means one system have three IP address but base IP address is 192.168.53.197

    Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >