Search Results

Search found 8923 results on 357 pages for 'wireless keyboard'.

Page 42/357 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

  • USB ports causing Wireless and Mobile Phone tethering drop out

    - by chrolli
    I have a problem with my USB ports and I can't seem to pinpoint the problem. I'm hoping that I can get some idea as to how to troubleshoot my problem. Problem description: I recently bought a USB Wireless Adapter in order to connect my Desktop PC to the WLAN. The dongle keeps dropping off connection regularly on average once a minute. And the connection is slow. What I've tried: I installed a network scanner to determine signal strength. The PC/adapter combo is getting about 70% signal strength. I have a laptop that has an internal Wireless adapter. I moved the laptop near the location of the PC. The signal strength was above 90%. I installed the USB adapter on the laptop. I placed the laptop near the location of the PC. The signal strength was above 80%. And there is no drop out issue. I've isolated the problem to be on the PC. I used internet tethering on my mobile phone in order to test the USB ports. I get the same problem, themobile phone keeps dropping in and out. I plugged the adapter and phone on all USB ports, and it is still dropping out on all ports. I've isolated the problem to be the Motherboard, USB hub. I updated the BIOS, and USB driver. Still dropping out. I noticed that when I used the mobile phone tethering method, the phone (iphone 5) is guarenteed to drop out and does not appear to charge if I jiggle the the 8-pin connector on the base of the phone. If I push the pin tightly on the phone, the phone starts charging, as soon as I let go, it stops and drops out from the PC. This is strange because this doesn't happen when it is plugged to the powerboard. Which means that the 8 pin connector is fine. I'm not sure what the problem is. I assume that it is to do with the USB ports not supplying enough power which in turn causes the devices to intermittently drop out. The reason I say this is because the USB cable works fine when plugged into a powerboard with enough power supplied to the phone. Only when it is plugged into the USB port on the PC, does it drop out. My motherboard is Asus P8z68-v le. My Wireless adapter is the D-link DWA131. I can't seem to find any settings in the BIOS to increase the south bridge voltage so as to supply more power to the USB ports. Although this problem only occurs when I'm trying to hook up to a device supplying internet connection. My USB HDD, Flash drives, and Mouse and Key are working fine! Any suggestions please?

    Read the article

  • Keyboard, Dual Monitor Question

    - by Dmn
    Im about to get a 23inch Monitor to connect to my laptop for programming, and general multimedia besides. (this is the monitor what do you think? LG 23" LCD And would you recommend getting a keyboard to use (ie not using the laptop one?) seems like it would be kinda awkward otherwise. This is the keyboard im looking at because it seems to have the low laptop style keys. ||| tigerdirect .com/applications/SearchTools/item-details.asp?EdpNo=5214790&sku=L23-0054 ||| or would you recommend something different? Thanks

    Read the article

  • Aruba Wireless Controller 200 and AP70 manual

    - by techie
    I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

    Read the article

  • How can I sort out Xephyr's keyboard mapping?

    - by qedi
    When I start up Xephyr inside of X, my keyboard map becomes wonky mostly just for non-printing characters. I can't use arrow keys. According to xev, The down arrow gets mapped to Super_R. The up arrow is Print Screen. PgDown is mapped to "Menu". My keyboard works fine in the original X display (:0), but in the Xephyr subdisplay (:1), nothing else quite works right. I don't have any funky xmodmap things going on in my main X display that I'm aware of. All I really do is setxkbmap -option ctrl:swapcaps.

    Read the article

  • Using a Netgear WGR614v9 to extend wireless signal from Netgear DG934GT

    - by moorcroft
    I'm wondering if someone could please provide me the steps for extending/repeating my wirless signal so that I can have greater wireless range throughout my house. I have 2 wirless Netgear routers, a DG934GT ADSL router (base unit) and WGR614v9 cable router (repeater). I've flashed both routers with the latest firmware and have turned on the wireless repeating function in the WGR614v9 but I can't get internet access when connected to the repeater, I can only get it when connected to the base unit. Can this be achieved by running an ethernet cable between the two routers as thus far I've only tried to get them to contact each other wirelessly. Any help would be appreciated

    Read the article

  • USB Keyboard not working under windows 7 x64?

    - by Comboo
    I have two usb keyboards, one no-name cheapo thing and an old logitech. When i plug them in to my computer they pop up in device manager as "Unknown device" respective "USB-receiver". Both of them fail to install any drivers, neighter automatically or through windows update. Both keyboards work perfectly on another computer i have with vista 32bit. Can this be one of those cases where a device does not work in 64bit version of windows? I doubt it though since I've never had that problem before with any device and i thought that basic things like keyboards would be kind of failsafe. I don't really know how to start debugging this issue. I've tried all the obvious, rebooting, changing usb-port etc. Are there any generic x64 keyboard drivers you can use? Is there any way to find the manufacturer of the keyboard over usb? There is nothing written on it.

    Read the article

  • What's the point of Netgear's WNHDB3004 "3DHD WIRELESS HOME THEATER NETWORKING KIT"

    - by badp
    Here's a crude representation of what I've got at home: floor 2 INTERNETS ---- MODEM/ROUTER ---- MY COMPUTER | floor 1 WIFI REPEATER ---- stuff | floor 0 more stuff TELEVISION Now, as part of our sat tv subscription we can get an additional service if we connect our decoder (located by TELEVISION obviously) to the internet. What they suggest is buying a Netgear 3DHD WIRELESS HOME THEATER NETWORKING KIT holy shit isn't my bullshit-o-meter flying high right now from the general buzzwordyness of this thing. What does this thing actually do that our existing wireless-enabled routers don't do? What's the point of having a third wifi router in the same house, this time only for one television? If I do decide to plunge €99 for this, should I connect it to the wifi repeater (which does not provide AAA quality internet, at least for all gaming purposes) or to my modem/router (risking issues with low signal?).

    Read the article

  • adding keyboard shortcuts for OSX terminal or xterm

    - by I J
    Is there a way to add a keyboard shortcut for a terminal command in OSX. Basically most of the times i open the terminal app in MAC in order to ssh into a certain server foo. What I want to do is add a keyboard shortcut (say ^k) so that on a terminal when I do that, it runs "ssh foo" in the terminal. Thanks PS: I think if there is something for the xterm in linux then it should work for the terminal too. So this might not be an OSX specific question. PS2: I want the shortcut to do carriage return with the "ssh foo". If its just "ssh foo", then I can write an alias in .bashrc. My goal is to minimize the number of keystrokes I've to do at the end of the day.

    Read the article

  • International Dvorak keyboard doesn't trigger hot-keys

    - by akurtser
    Hi, I just configured a Hebrew-Dvorak keyboard with Keyboard Layout Manager. What this means is that when I hold Shift+any key, the input is the capital English letter. It works just fine, however, hot-keys that involves the Ctrl key aren't being triggered when the input language is set to Hebrew (i.e Ctrl+L in FF which should set the focus on the URL bar) If however I hit the matching Qwerty key (input lang=Hebrew) I get the desirable result (i.e the URL bar get focused). The only thing I can think of is completely removing the US-Qwerty layout, but I don't know how this can be achieved, and besides, it may not solve the problem. Thanks, Almog.

    Read the article

  • Wireless card not found on Ubuntu

    - by Idealflip
    Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

    Read the article

  • Internet wireless connected with limited access, windows vista

    - by r0ca
    I had some malware in my computer so I did a bit of manual work to remove it including resetting TCP/IP. Now the malware is gone. I can see my home wireless network and I can get connected to it but when connected I get the Internet wireless connected with limited access message. When I go to the IE I cannot browse. When I tried to ping 192.168.1.1 I got an Error Code 1231 Unconnected Network Problem. I have deactivated my Windows firewall as I thought it could be hyperactive security. Still no luck. I have Norton but it is not active, I have also Avast and AVG installed but they are not active. Any ideas?

    Read the article

  • Windows 7 keeps changing my language(keyboard) settings

    - by Hans
    I am using Windows 7 Ultimate on a Windows network. My default settings is Danish locale, Danish keyboardlayout, but English system language. I only have Danish keyboard layout installed (in Text Services and Input Languages). However, at the login screen I can choose Danish and English, but whatever I choose Windows 7 changes system language (and keyboard layout!) to English (United States). Since this is a per-App setting I must change the language setting (language bar in the taskbar) Where can this be changed system wide and permament?

    Read the article

  • Aruba Wireless Controller 200 and AP70 manual

    - by techie
    I have an Aruba wireless system that is currently in use but there is no documentation from the previous person in charge. I have no manuals or login information for the wireless controllers and APs. I checked the Aruba website and you need to register to access the support information but registration isn't instant and takes several days. I've waited for quite a while now and have tried googling and checking the Aruba forums but have found no indication of a manual. What I really need is the ability to reset the controller and APs so I can access the device with the default username and password. There is no reset button on this device so I have no idea how you go about resetting the controller and APs. Hm it seems I can't create a new tag as a new user. If possible can someone add an "Aruba" tag?

    Read the article

  • unable to sniff traffic despite network interface being in monitor or promiscuous mode

    - by user65126
    I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

    Read the article

  • Cannot remove wireless network profile even though admin account is used

    - by David Karlsson
    On my windows computer which is connected to a company domain. I have problems with the wireless networking. First of all the computer fails to connect. Second of all I cannot remove the network from the list of wireless profiles. The properties window simply claims that "This network is administered by the Administartor Account". I am currently logged in as the local administrator. I have also tried creating a new admin account and still get the same problem when trying to remove the network. My computer has only the microsoft security essentials antivirus and some VMWare+virtual box connections that I can figure might interfere, but disabling realtime protection has not helped me on this. I also cannot delete the virtual network adapters from the control panel / network adapters...

    Read the article

  • Can't connect to wireless-n in dual mode.

    - by Tyllyn
    I recently purchased a Acer Aspire Revo AR3610-U9022. This little nettop uses a Atheros AR5B91 Wireless Network Adapter. I also have a Netgear RangeMax NEXT Wireless Route (model WNDR3300). I have been using this router in dual mode (11G and 11N) on my normal desktop without a problem (Mode: Up to 270Mbps at 5GHz & 54Mbps at 2.4 GHz), but doing this, my Revo won't detect the 11N network as being around... my desktop still does, but the Revo, nope... just the 11G. However, when I switch my router over to just "Up to 270Mbps at 2.4GHz", it kills the 11G entirely, but the Revo recognizes the 11N network. I'm a programmer by trade, and this hardware-y stuff confuses me more than it should. Is there any way that I could set this stuff up so my Revo can connect to the 11N part of my router, but keep the 11G around? :) Thanks!

    Read the article

  • Keyboard / mouse freeze

    - by ajvb
    Hello, Pretty much on a daily basis the keyboard & mouse on my Dell PC stop responding. I have left the PC on for over 10 minutes but still no response so I have to power on / off. Keyboard / mouse then work fine. I did have 2 mice attached to the PC but I have now removed one to see if this makes any difference. CPU temperatures are 51C & 48C - dont know whether this is normal or high? OS is Windows 7. Adrian

    Read the article

  • WinXP keyboard input repeat rate problem

    - by Victor Sorokin
    I have problem similar to http://superuser.com/questions/33981/problems-with-kvm-switch-and-keyboard-repeat-rate-on-windows-xp: When I press and hold some key it's repeated random number of times, after that repeat stops and I need to release key and press it again to make repeat continue. If there's simultaneous sound playback and repeat is stopped, sound's stuck while I hold key with unpleasant drumming as if there's some audio problem. This issue is reproducible in WinXP Safe Mode. On the same config under Linux there's no issue. My config: List item PS/2 Logitech Keyboard USB Mouse MB M3A/H-HDMI WinXP Pro English SP2 with added Russian layout (WinXP loads via GRUB2) Realtek audio drivers for AC97 Thanks for your suggestions J

    Read the article

  • Which keyboard has better ergomics?

    - by Absolute0
    When I was a kid I fell hard on my right wrist and since then I always get wrist pains when angling my wrist very high up (ie: when using a very high shaped mouse or doing push ups). So I have narrowed down my choices for a keyboard to the following 2: Microsoft Natural 4000: And the Razer Arctosa: The Razer is a slim type keyboard similar to a laptop feel and the hand-rest would help with keeping my hands straight with respect to my forearms. I am more inclined on getting the razer but am not sure if this will benefit my wrists in the long run. Any thoughts on this would be greatly appreciated. Thanks.

    Read the article

  • Cheapest Embedded System with Wireless Connectivity?

    - by geeko
    Problem: I'm trying to capture some information coming from keyboard, mouse and barcode reader connected to some PC via PS/2, USB and/or RS-232, before information get to PC and send it over the Internet to some central server. I'm thinking to do so by using some kind of hardware interface (middleware, if you like) between PC and input devices. I thought this interface can be embedded PC, PDA or simply some mobile phone with wireless connectivity. PS/2 and RS-232 could be converted to USB using some USB convector/hub that connects to one of these interface systems. Then some special API programming take place to communicate between PC, input devices and wireless server, in the form of application running on the interface system. What's the cheapest solution that can achieve this? Or possibly any other solution?

    Read the article

  • Removing QWERTY Keyboard Layout Permanently

    - by Phoenix
    Following the instructions in this thread, I added the Dvorak layout to the Regional and Language Options control panel, set it as the default keyboard layout and removed the US (QWERTY) layout. However, even though I removed the QWERTY layout, it still appears in my language bar, and my system defaults to it in every new window. This persists after a log-out/log-in and even a system restart. How do I remove the QWERTY keyboard layout from my system permanently? Alternatively (if outright removing QWERTY is just impossible), can I get Windows to default to Dvorak instead of QWERTY for new windows?

    Read the article

  • How can I easily identify all keyboard shortcuts (hotkeys) on OS X and current running Applications

    - by Michael Prescott
    By default, the function keys on my MacBook Pro control various hardware features and native operating system applications like the brightness of the LCD, Expose, or iTunes. I like these buttons and can use the fn button to take advantage of application Function keys when working with certain applications. Some service-type, background applications also have useful keyboard shortcuts. I tend to forget which keys are active at the moment and sometimes launch the wrong processes. Is there an application or operating system, native way of identifying all of the currently available keyboard shortcuts?

    Read the article

  • Debian Testing install USB menu does not respond to keyboard

    - by neurolysis
    I'm trying to install Debian Testing onto my Acer Aspire One ZG5 using the testing versions of boot.img and debian-testing-i386-CD-1.iso. I previously installed (two days ago) the latest release of stable, and the boot.img/CD1 from that worked fine, and installed seamlessly. With testing though, the menu does not respond to the keyboard as soon as the menu appears to select Install/Graphical install/Help, etc. I have also tried to boot with an external (USB) keyboard, which again, works fine with the stable version of boot.img/CD1, but not testing. I did some searching and couldn't find anything that looked similar. Any ideas?

    Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >