Search Results

Search found 11262 results on 451 pages for 'important directories'.

Page 420/451 | < Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427  | Next Page >

• How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

  - by cagenut

  Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

  Read the article

• Performance Tuning a High-Load Apache Server

  - by futureal

  I am looking to understand some server performance problems I am seeing with a (for us) heavily loaded web server. The environment is as follows: Debian Lenny (all stable packages + patched to security updates) Apache 2.2.9 PHP 5.2.6 Amazon EC2 large instance The behavior we're seeing is that the web typically feels responsive, but with a slight delay to begin handling a request -- sometimes a fraction of a second, sometimes 2-3 seconds in our peak usage times. The actual load on the server is being reported as very high -- often 10.xx or 20.xx as reported by top. Further, running other things on the server during these times (even vi) is very slow, so the load is definitely up there. Oddly enough Apache remains very responsive, other than that initial delay. We have Apache configured as follows, using prefork: StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 And KeepAlive as: KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 Looking at the server-status page, even at these times of heavy load we are rarely hitting the client cap, usually serving between 80-100 requests and many of those in the keepalive state. That tells me to rule out the initial request slowness as "waiting for a handler" but I may be wrong. Amazon's CloudWatch monitoring tells me that even when our OS is reporting a load of 15, our instance CPU utilization is between 75-80%. Example output from top: top - 15:47:06 up 31 days, 1:38, 8 users, load average: 11.46, 7.10, 6.56 Tasks: 221 total, 28 running, 193 sleeping, 0 stopped, 0 zombie Cpu(s): 66.9%us, 22.1%sy, 0.0%ni, 2.6%id, 3.1%wa, 0.0%hi, 0.7%si, 4.5%st Mem: 7871900k total, 7850624k used, 21276k free, 68728k buffers Swap: 0k total, 0k used, 0k free, 3750664k cached The majority of the processes look like: 24720 www-data 15 0 202m 26m 4412 S 9 0.3 0:02.97 apache2 24530 www-data 15 0 212m 35m 4544 S 7 0.5 0:03.05 apache2 24846 www-data 15 0 209m 33m 4420 S 7 0.4 0:01.03 apache2 24083 www-data 15 0 211m 35m 4484 S 7 0.5 0:07.14 apache2 24615 www-data 15 0 212m 35m 4404 S 7 0.5 0:02.89 apache2 Example output from vmstat at the same time as the above: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 8 0 0 215084 68908 3774864 0 0 154 228 5 7 32 12 42 9 6 21 0 198948 68936 3775740 0 0 676 2363 4022 1047 56 16 9 15 23 0 0 169460 68936 3776356 0 0 432 1372 3762 835 76 21 0 0 23 1 0 140412 68936 3776648 0 0 280 0 3157 827 70 25 0 0 20 1 0 115892 68936 3776792 0 0 188 8 2802 532 68 24 0 0 6 1 0 133368 68936 3777780 0 0 752 71 3501 878 67 29 0 1 0 1 0 146656 68944 3778064 0 0 308 2052 3312 850 38 17 19 24 2 0 0 202104 68952 3778140 0 0 28 90 2617 700 44 13 33 5 9 0 0 188960 68956 3778200 0 0 8 0 2226 475 59 17 6 2 3 0 0 166364 68956 3778252 0 0 0 21 2288 386 65 19 1 0 And finally, output from Apache's server-status: Server uptime: 31 days 2 hours 18 minutes 31 seconds Total accesses: 60102946 - Total Traffic: 974.5 GB CPU Usage: u209.62 s75.19 cu0 cs0 - .0106% CPU load 22.4 requests/sec - 380.3 kB/second - 17.0 kB/request 107 requests currently being processed, 6 idle workers C.KKKW..KWWKKWKW.KKKCKK..KKK.KKKK.KK._WK.K.K.KKKKK.K.R.KK..C.C.K K.C.K..WK_K..KKW_CK.WK..W.KKKWKCKCKW.W_KKKKK.KKWKKKW._KKK.CKK... KK_KWKKKWKCKCWKK.KKKCK.......................................... ................................................................ From my limited experience I draw the following conclusions/questions: We may be allowing far too many KeepAlive requests I do see some time spent waiting for IO in the vmstat although not consistently and not a lot (I think?) so I am not sure this is a big concern or not, I am less experienced with vmstat Also in vmstat, I see in some iterations a number of processes waiting to be served, which is what I am attributing the initial page load delay on our web server to, possibly erroneously We serve a mixture of static content (75% or higher) and script content, and the script content is often fairly processor intensive, so finding the right balance between the two is important; long term we want to move statics elsewhere to optimize both servers but our software is not ready for that today I am happy to provide additional information if anybody has any ideas, the other note is that this is a high-availability production installation so I am wary of making tweak after tweak, and is why I haven't played with things like the KeepAlive value myself yet.

  Read the article

• Screen -X exec commands not working until manually attached

  - by James Watt

  I have a batch script that starts a java server application inside of a screen. The command looks like this: cd /dir/ && screen -A -m -d -S javascreen java -Xms640M -Xmx1024M -jar javaserverapp.jar nogui After I run the batch script, it starts the server and puts it inside the correct screen. If I list my screens after, I see something like this: user@gtwy /dir $ screen -list There is a screen on: 16180.javascreen (Detached) 1 Socket in /var/run/screen/S-user. However, I have a second batch script that sends automated commands to this server and runs on a different crontab interval. Because of the way the application works, I send commands to it like this (this command tells it to alert connected users "testing 123"): screen -X exec .\!\! echo say testing 123 I've also tried: screen -R -X exec .\!\! echo say testing 123 screen -S javascreen -X exec .\!\! echo say testing 123 Unfortunately, these commands DO NOT WORK. They don't even give me an error message, they just do nothing. HOWEVER - If I manually attach to the screen first (with the below command) and then detach, now I can run any of the above commands flawlessly. I can demonstrate this with a video, if I wasn't clear enough here. screen -r -d Thanks in advance. Update: here is the important parts of /etc/screenrc. It should be totally vanilla, I've never edited this file. # VARIABLES # =============================================================== # No annoying audible bell, using "visual bell" # vbell on # default: off # vbell_msg " -- Bell,Bell!! -- " # default: "Wuff,Wuff!!" # Automatically detach on hangup. autodetach on # default: on # Don't display the copyright page startup_message off # default: on # Uses nethack-style messages # nethack on # default: off # Affects the copying of text regions crlf off # default: off # Enable/disable multiuser mode. Standard screen operation is singleuser. # In multiuser mode the commands acladd, aclchg, aclgrp and acldel can be used # to enable (and disable) other user accessing this screen session. # Requires suid-root. multiuser off # Change default scrollback value for new windows defscrollback 1000 # default: 100 # Define the time that all windows monitored for silence should # wait before displaying a message. Default 30 seconds. silencewait 15 # default: 30 # bufferfile: The file to use for commands # "readbuf" ('<') and "writebuf" ('>'): bufferfile $HOME/.screen_exchange # # hardcopydir: The directory which contains all hardcopies. # hardcopydir ~/.hardcopy # hardcopydir ~/.screen # # shell: Default process started in screen's windows. # Makes it possible to use a different shell inside screen # than is set as the default login shell. # If begins with a '-' character, the shell will be started as a login shell. # shell zsh # shell bash # shell ksh shell -$SHELL # shellaka '> |tcsh' # shelltitle '$ |bash' # emulate .logout message pow_detach_msg "Screen session of \$LOGNAME \$:cr:\$:nl:ended." # caption always " %w --- %c:%s" # caption always "%3n %t%? @%u%?%? [%h]%?%=%c" # advertise hardstatus support to $TERMCAP # termcapinfo * '' 'hs:ts=\E_:fs=\E\\:ds=\E_\E\\' # set every new windows hardstatus line to somenthing descriptive # defhstatus "screen: ^En (^Et)" # don't kill window after the process died # zombie "^["

  Read the article

• Strange Upload Problem on Hyper-V

  - by Ring0

  Hi, This one is driving me totally nuts. I have being trying to upload a file to www.virustotal.com (its a harmless exe I have since found out - DiskWipe.exe from diskwipe.org). Using IE8. From Win 7 and Win 2008 R2 Datacenter (which I select to boot from vhd's) onto my main machine hardware, and also on another Win 7 PC elsewhere on my network, when I upload the file to virustotal.com it works perfectly. So, using my native NIC's everything is fine. Using another machine also perfect. Right. OK, from my boot menu the default is my main development machine - the one I'm typing on now. This runs on the metal and has Hyper-V role and I have some guests. All guests are not running. Amazingly, from my console (root partition to be exact) or any guest OS 2003 /XP / 2008 R2 etc. My upload to virustotal.com slows at 32% then HANGS at 38.something% & never finishes!! Here is the kicker. I have another box (my main server) running Hyper-V on the metal and three live guests. Identical H/W to my main dev machine in another room. (Except OS is Datacenter - Mine is Enterprise). If I try and upload from its bare metal console or any guest this file to virustotal.com using IE8 it stops exactly in the same place!! As for "steps I have tried etc." are kind-of blown out of the water as my server box is doing the precise same thing as the machine in my room here. OK, comonalities: Mobo: Gigabyte GA-X58-UD5, 12GB Kingston RAM, Corei7 920 4 cores hyperthreading = 8 & Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC's. All 3 machines have this same motherboard - revision F11 Bios, all have 12GB RAM, all have the Realtek Nic's. All x64 by the way as I mentioned before I have a Win 7 box also with the UD5 m/Board, 12 GB RAM - bit of an overkill. :-) All these machines when NOT running Hyper-V can upload this file. Perhaps you may like to try it on a Hyepr-v (2008 R2) yourselves with IE8 and the desktop experience is on. See if it works or fails for you. Root OS or any guest. So, looking like its the NIC + Hyper-V = Cannot upload this file (any file I must add.) Realtek Nic is Ver 7.002.1125.2008. Using IE8 I see in the nic settings there are the usual parameters for Jumbo frames / Checksum offloading etc. several others. Should I fiddle with these? I ran Netmon 3.3 in a guest and the TCP session halted as the upload failed. I suppose I could study that further. I dont have Netmon on the root partition machine (yet)! All OS's fully patched - including todays defender files. My box running Office 2007 - but identical server in another room is not. Also, if I fire up a VPN to a distant client and do the upload it works! Of course its a different network path. Suggestions welcome please. If I left out anything important - please yell at me. Many Thanks,

  Read the article

• COPSSH RSA only authentication connection problem

  - by Siriss

  Hello all- I am trying to setup an RSA Authentication only SSH/SFTP server. The SSH will be used primarily for RDC. Everything works just fine if I use password authentication. I am using Putty Key Generator to create he keys and I have pasted the key into authorized_keys file and restarted the OpenSSH server. I am using FileZilla to test the SFTP connection as that is the most important. For my tests I have created the keys without password correction. It will not work with a standard SSH connection either. It says "Server refused our key". I have recreated the key twice double checking with a guide on google, and I am pretty sure I did it correctly. I load the key file into FileZilla under settings/SFTP and try to connect and I get the following error: Disconnected: No supported authentication methods available. I have been playing with the different settings all night and I cannot figure it out. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m PermitRootLogin no #StrictModes yes #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! PasswordAuthentication no PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM no #AllowAgentForwarding yes #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /bin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs # X11Forwarding no # AllowTcpForwarding no # ForceCommand cvs server Thank you so much for your help!

  Read the article

• apache webserver unresponsible with server-status showing all child processes waiting for connection

  - by Jeff

  My setup: i have 3 nearly identical webserver machines serving the same high loaded dynamic website with simple load balancing over dns. The service has been working for over two ears with the same apache config. apache2, php5, ubuntu 8.04 linux 2.6.24-29-server My problem: since about two weeks i'm experiencing problems with this config. Nearly every day i have one small moment about 5 minutes, in which the website is unreachable. I'm still able to login to the servers over ssh. If i run htop, i see the machine simply doing nothing. i have about 1000 apache processes running, but no cpu activity. i've used the apache mod_status to debug this situation. the process scoreboard looks like this: _C.___K_______________________R._______.__K_K____K___C_______.__ _______C__________.___________________________________.________C _.____K__________K___K_WK_____._K_____________________________._ W______K__________K________.____________________._______C_______ _C_.__K__K____.._.._____________________________________C_______ _R___________K___.______C________.C_________.______._____C______ ____________KKC____K_____K__WC_________________C_____.__.____.__ _____________________C_________K______.____C______._____________ _.___C____.___.___________________________.K______.____K________ W__.___________________C.__.____K________K_______R_._.__._______ __C__C_.__________C__C_______._____W______________C_.___C_______ ____.______C_____________C________.____C____________.________._K __.__________.K_____________K_________._____C____.K__________KW_ __K.W________R_________._______.___W___________.____.__K_____W__ W___.___..________W____K Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process So the most of the processes are just waiting for connection. after about 5 minutes the situation will return to normal: i have lot least processes on every machine, the most workers have the "."-status (meaing they are open to process a request) and of course the website is reachable! so i'm trying to find something in the logs, but there is simply nothing... the apache access log is silent for about 4 minutes, the same is for the error log. i also can not figure out anything wrong in other system logs. the situation is the same on all 3 webservers (all of them have this load peak and unresposibility at the same time), so i do not thing this is hardware related. but i think, this might be related to some network (tcp) issue. any ideas? EDIT: some more information, that i have just discovered: it has just happened again. and i was able to verify that i'm also not able to connect locally when this problem occurs. i have made some connection statistics with the following command after it happend netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 109 CLOSE_WAIT 2652 ESTABLISHED 2 FIN_WAIT1 11 LAST_ACK 12 LISTEN 91 SYN_RECV 1 SYN_SENT 16 TIME_WAIT If i execute the same command some time later, i have something like this: 4 CLOSING 108 ESTABLISHED 18 FIN_WAIT1 182 FIN_WAIT2 37 LAST_ACK 12 LISTEN 50 SYN_RECV 11276 TIME_WAIT So in the normal situation i have only 100-200 open connections by clients beeing handled by apache in this moment. when i have this "crash", i have a lot more connections. what is the best way to analyse this? EDIT2: the important lines in apache2.conf are: KeepAlive On MaxKeepAliveRequests 20 KeepAliveTimeout 1 <IfModule mpm_prefork_module> ServerLimit 920 StartServers 30 MinSpareServers 80 MaxSpareServers 120 MaxClients 920 MaxRequestsPerChild 700 </IfModule> it is an apache2 prefork with php_mod. the server has 8GB ram and a 4gb swap partition.

  Read the article

• Postfix logs missing information on delivery status (postfix/smtp message)

  - by hegemon

  I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

  Read the article

• how to use ajax with json in ruby on rails

  - by rafik860

  I am implemeting a facebook application in rails using facebooker plugin, therefore it is very important to use this architecture if i want to update multiple DOM in my page. if my code works in a regular rails application it would work in my facebook application. i am trying to use ajax to let the user know that the comment was sent, and update the comments bloc. migration: class CreateComments < ActiveRecord::Migration def self.up create_table :comments do |t| t.string :body t.timestamps end end def self.down drop_table :comments end end controller: class CommentsController < ApplicationController def index @comments=Comment.all end def create @comment=Comment.create(params[:comment]) if request.xhr? @comments=Comment.all render :json=>{:ids_to_update=>[:all_comments,:form_message], :all_comments=>render_to_string(:partial=>"comments" ), :form_message=>"Your comment has been added." } else redirect_to comments_url end end end view: <script> function update_count(str,message_id) { len=str.length; if (len < 200) { $(message_id).innerHTML="<span style='color: green'>"+ (200-len)+" remaining</span>"; } else { $(message_id).innerHTML="<span style='color: red'>"+ "Comment too long. Only 200 characters allowed.</span>"; } } function update_multiple(json) { for( var i=0; i<json["ids_to_update"].length; i++ ) { id=json["ids_to_update"][i]; $(id).innerHTML=json[id]; } } </script> <div id="all_comments" > <%= render :partial=>"comments/comments" %> </div> Talk some trash: <br /> <% remote_form_for Comment.new, :url=>comments_url, :success=>"update_multiple(request)" do |f|%> <%= f.text_area :body, :onchange=>"update_count(this.getValue(),'remaining');" , :onkeyup=>"update_count(this.getValue(),'remaining');" %> <br /> <%= f.submit 'Post'%> <% end %> <p id="remaining" >&nbsp;</p> <p id="form_message" >&nbsp;</p> <br><br> <br> if i try to do alert(json) in the first line of the update_multiple function , i got an [object Object]. if i try to do alert(json["ids_to_update"][0]) in the first line of the update_multiple function , there is no dialog box displayed. however the comment got saved but nothing is updated. it seems like the object sent by rails is nil or cant be parsed by JSON.parse(json). questions: 1.how can javascript and rails know that i am dealing with json objects?deos ROR sent it a object format or a text format?how can it check that the json object has been sent 2.how can i see what is the returned json?do i have to parse it?how? 2.how can i debug this problem? 3.how can i get it to work?

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Squid - Logging to MySQL without empty rows/skipped records?

  - by Lee Ward

  I'm trying to figure out how to make Squid proxy log to MySQL. I know ACL order is pretty important but I'm not sure if I understand exactly what ACLs are or do, it's difficult to explain, but hopefully you'll see where I'm going with this as you read! I have created the lines to make Squid interact with a helper in squid.conf as follows: external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log The external ACL helper (mysql_lg.php) is a PHP script and is as follows: error_reporting(0); if (! defined(STDIN)) { define("STDIN", fopen("php://stdin", "r")); } $res = mysql_connect('localhost', 'squid', 'testsquidpw'); $dbres = mysql_select_db('squid', $res); while (!feof(STDIN)) { $line = trim(fgets(STDIN)); $fields = explode(' ', $line); $user = rawurldecode($fields[0]); $cli_ip = rawurldecode($fields[1]); $protocol = rawurldecode($fields[2]); $uri = rawurldecode($fields[3]); $q = "INSERT INTO logs (id, user, cli_ip, protocol, url) VALUES ('', '".$user."', '".$cli_ip."', '".$protocol."', '".$uri."');"; mysql_query($q) or die (mysql_error()); if ($fault) { fwrite(STDOUT, "ERR\n"); }; fwrite(STDOUT, "OK\n"); } The configuration I have right now looks like this: ## Authentication Handler auth_param ntlm program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 30 auth_param negotiate program /usr/bin/ntlm_auth --helper-protocol=squid-2.5-basic auth_param negotiate children 5 # Allow squid to update log external_acl_type mysql_log %LOGIN %SRC %PROTO %URI php /etc/squid3/custom/mysql_lg.php acl ex_log external mysql_log http_access allow ex_log acl localnet src 172.16.45.0/24 acl AuthorizedUsers proxy_auth REQUIRED acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl CONNECT method CONNECT acl blockeddomain url_regex "/etc/squid3/bl.acl" http_access deny blockeddomain deny_info ERR_BAD_GENERAL blockeddomain # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # Allow the internal network access to this proxy http_access allow localnet # Allow authorized users access to this proxy http_access allow AuthorizedUsers # FINAL RULE - Deny all other access to this proxy http_access deny all From testing, the closer to the bottom I place the logging lines the less it logs. Oftentimes, it even places empty rows in to the MySQL table. The file-based logs in /var/log/squid3/access.log are correct but many of the rows in the access logs are missing from the MySQL logs. I can't help but think it's down to the order I'm putting lines in because I want to log everything to MySQL, unauthenticated requests, blocked requests, which category blocked a specific request. The reason I want this in MySQL is because I'm trying to have everything managed via a custom web-based frontend and want to avoid using any shell commands and access to system log files if I can help it. The end result is to make it as easy as possible to maintain without keeping staff waiting on the phone whilst I add a new rule and reload the server! Hopefully someone can help me out here because this is very much a learning experience for me and I'm pretty stumped. Many thanks in advance for any help!

  Read the article

• Using PHP to connect to RADIUS works on one server but not another

  - by JDS

  I have a fleet of webservers that server a LAMP webapp broken into multiple customer apps by virtualhost/domain. The platform is Ubuntu 10.04 VM + PHP 5.3 + Apache 2.2.14, on top of VMware ESX (v4 I think). This stuff's not too important, though -- I'm just setting up the background. I have one customer that connects to a RADIUS server for authentication. We've found that the app responds as if some number of web servers are configured correctly and some are not. i.e. Apparently random authentication failures or successes, with no rhyme or reason. I did a lot of analysis of our fleet, and resolved it down to the differences between two specific web servers. I'll call them "A" and "B". "A" works. "B" does not. "Works" means "connects to and gets authentication data successfully from the RADIUS server". Ultimately, I'm looking for one thing that is different, and I've exhausted everything that I can come up with, so, looking for something else. Here are things I've looked at PHP package versions (all from Ubuntu repos). These are exactly the same across servers. PECL package. There are no PECL packages that aren't installed by apt. Other libraries or packages. Nothing that was network-related or RADIUS-related was different among servers. (There were some minor package differences, though.) Network or hosting environment. I found that some of the working servers were on the same physical environment as some not-working ones (i.e. same ESX containers). So, probably, the physical network layer is not the problem. Test case. I created a test case as follows. It works on the working servers, and fails on the not-working servers, very consistently. <?php $radius = radius_auth_open(); $username = 'theusername'; $password = 'thepassword'; $hostname = '12.34.56.78'; $radius_secret = '39wmmvxghg'; if (! radius_add_server($radius,$hostname,0,$radius_secret,5,3)) { die('Radius Error 1: ' . radius_strerror($radius) . "\n"); } if (! radius_create_request($radius,RADIUS_ACCESS_REQUEST)) { die('Radius Error 2: ' . radius_strerror($radius) . "\n"); } radius_put_attr($radius,RADIUS_USER_NAME,$username); radius_put_attr($radius,RADIUS_USER_PASSWORD,$password); switch (radius_send_request($radius)) { case RADIUS_ACCESS_ACCEPT: echo 'GOOD LOGIN'; break; case RADIUS_ACCESS_REJECT: echo 'BAD LOGIN'; break; case RADIUS_ACCESS_CHALLENGE: echo 'CHALLENGE REQUESTED'; break; default: die('Radius Error 3: ' . radius_strerror($radius) . "\n"); } ?>

  Read the article

• How do you re-mount an ext3 fs readwrite after it gets mounted readonly from a disk error?

  - by cagenut

  Its a relatively common problem when something goes wrong in a SAN for ext3 to detect the disk write errors and remount the filesystem read-only. Thats all well and good, only when the SAN is fixed I can't figure out how to re-re-mount the filesystem read-write without rebooting. Behold: [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][active] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] [root@localhost ~]# mount /dev/mapper/mpath0 /mnt/foo [root@localhost ~]# touch /mnt/foo/blah All good, now I yank the LUN out from under it. [root@localhost ~]# touch /mnt/foo/blah [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system [root@localhost ~]# tail /var/log/messages Mar 18 13:17:33 localhost multipathd: sdb: tur checker reports path is down Mar 18 13:17:34 localhost multipathd: sdc: tur checker reports path is down Mar 18 13:17:35 localhost kernel: Aborting journal on device dm-2. Mar 18 13:17:35 localhost kernel: Buffer I/O error on device dm-2, logical block 1545 Mar 18 13:17:35 localhost kernel: lost page write due to I/O error on dm-2 Mar 18 13:17:36 localhost kernel: ext3_abort called. Mar 18 13:17:36 localhost kernel: EXT3-fs error (device dm-2): ext3_journal_start_sb: Detected aborted journal Mar 18 13:17:36 localhost kernel: Remounting filesystem read-only It only thinks its read-only, in reality its not even there. [root@localhost ~]# multipath -ll sdb: checker msg is "tur checker reports path is down" sdc: checker msg is "tur checker reports path is down" mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=0][hwhandler=0][rw] \_ round-robin 0 [prio=0][enabled] \_ 1:0:0:1 sdb 8:16 [failed][faulty] \_ 2:0:0:1 sdc 8:32 [failed][faulty] [root@localhost ~]# ll /mnt/foo/ ls: reading directory /mnt/foo/: Input/output error total 20 -rw-r--r-- 1 root root 0 Mar 18 13:11 bar How it still remembers that 'bar' file being there... mystery, but not important right now. Now I re-present the LUN: [root@localhost ~]# tail /var/log/messages Mar 18 13:23:58 localhost multipathd: sdb: tur checker reports path is up Mar 18 13:23:58 localhost multipathd: 8:16: reinstated Mar 18 13:23:58 localhost multipathd: mpath0: queue_if_no_path enabled Mar 18 13:23:58 localhost multipathd: mpath0: Recovered to normal mode Mar 18 13:23:58 localhost multipathd: mpath0: remaining active paths: 1 Mar 18 13:23:58 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:58 localhost multipathd: dm-2: devmap already registered Mar 18 13:23:59 localhost multipathd: sdc: tur checker reports path is up Mar 18 13:23:59 localhost multipathd: 8:32: reinstated Mar 18 13:23:59 localhost multipathd: mpath0: remaining active paths: 2 Mar 18 13:23:59 localhost multipathd: dm-2: add map (uevent) Mar 18 13:23:59 localhost multipathd: dm-2: devmap already registered [root@localhost ~]# multipath -ll mpath0 (36001f93000a310000299000200000000) dm-2 XIOTECH,ISE1400 [size=1.1T][features=1 queue_if_no_path][hwhandler=0][rw] \_ round-robin 0 [prio=2][enabled] \_ 1:0:0:1 sdb 8:16 [active][ready] \_ 2:0:0:1 sdc 8:32 [active][ready] Great right? It says [rw] right there. Not so fast: [root@localhost ~]# touch /mnt/foo/blah touch: cannot touch `/mnt/foo/blah': Read-only file system OK, doesn't do it automatically, I'll just give it a little push: [root@localhost ~]# mount -o remount /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only The hell you are: [root@localhost ~]# mount -o remount,rw /mnt/foo mount: block device /dev/mapper/mpath0 is write-protected, mounting read-only Noooooooooo. I have tried all sorts of different mount/tune2fs/dmsetup commands and I cannot figure out how to get it to un-flag the block device as write-protected. Rebooting will fix it, but I'd much rather do it on-line. An hour of googling has gotten me nowhere either. Save me ServerFault.

  Read the article

• Installing EclipseFP on Mac OS X

  - by Dom Kennedy

  I am trying to install EclipseFP. I'm running OS X Mavericks. I've tried following both the official installation instructions and the advice in this answer on SU, but I'm still having the same problem. I can get the plugin itself installed painlessly using Help -> Install New Software..., Bbut when I restart and switch to the Haskell perspective, things start to go wrong. The installation instructions tells me that I should receive a prompt to install BuildWrapper and Scion Browser. I do not receive this prompt. Furthermore, if I create a new Haskell project, my code has no syntax highlighting, and the Hoogle search feature does not appear to do anything. It's clear that the plugin is not set up correctly yet. I've tried running cabal update in Terminal, but this does not change anything. After several attempts going round in circles with this on Eclipse Juno, I uninstalled Eclispe and the Haskell Platform and performed a clean install of Eclipse Luna and the latest Haskell Platform. However, the problems are persisting. I've tried going into Preferences to see if I could sort any of this out manually. I should initially point out that my GHC installation seems to be correctly references under Preferences -> Haskell Implementations Under Haskell -> Helper executables, there are areas for configuring the options of both BuildWrapper and Scion Browser. At present, both are blank. I tried clicking the Install from Hackage... button beside each of them with no success; I receive an error message saying Expected executable <workspace>/.metadata/.plugins/net.sf.eclipsefp.haskell.ui/sandbox/.cabal-sandbox/bin/buildwrapper not found!` (replace buildwrapper for scion-browser and the message is the same) The Eclipse console displays the following exception after doing the above with BuildWrapper: src/Language/Haskell/BuildWrapper/GHCStorage.hs:313:32: Not in scope: data constructor ‘MatchGroup’ cabal.real: Error: some packages failed to install: buildwrapper-0.7.4 failed during the building phase. The exception was: ExitFailure 1 and after doing it for Scion-Browser: zip-archive-0.2.3.4 (reinstall) changes: text-1.1.0.0 -> 0.11.3.1 pandoc-1.12.3.3 (latest: 1.13) -http-conduit (new version) Graphalyze-0.14.1.0 (reinstall) changes: pandoc-1.12.4.2 -> 1.12.3.3, text-1.1.0.0 -> 0.11.3.1 cabal.real: The following packages are likely to be broken by the reinstalls: pandoc-1.12.4.2 unordered-containers-0.2.4.0 aeson-0.7.0.4 scientific-0.2.0.2 case-insensitive-1.1.0.3 HTTP-4000.2.10 Use --force-reinstalls if you want to install anyway. After receiving similar results as the above on previous attempts, I've tried using force-reinstalls and ended up at more dead ends. I am at a loss as to what is wrong and how to solve this. I should point out that my GHC installation appears to be correctly configured under Preferences -> Haskell -> Haskell Implementations. Apologies if any of this information is irrelevant, I'm just not really sure what is important and what isn't at this point. Any help anyone could provide me with would be greatly appreciated.

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• File server share access intermittent/slow/machine unstable: win2kr2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• Log transport and aggregation at scale

  - by markdrayton

  How're you analysing log files from UNIX/Linux machines? We run several hundred servers which all generate their own log files, either directly or through syslog. I'm looking for a decent solution to aggregate these and pick out important events. This problem breaks down into 3 components: 1) Message transport The classic way is to use syslog to log messages to a remote host. This works fine for applications that log into syslog but less useful for apps that write to a local file. Solutions for this might include having the application log into a FIFO connected to a program to send the message using syslog, or by writing something that will grep the local files and send the output to the central syslog host. However, if we go to the trouble of writing tools to get messages into syslog would we be better replacing the whole lot with something like Facebook's Scribe which offers more flexibility and reliability than syslog? 2) Message aggregation Log entries seem to fall into one of two types: per-host and per-service. Per-host messages are those which occur on one machine; think disk failures or suspicious logins. Per-service messages occur on most or all of the hosts running a service. For instance, we want to know when Apache finds an SSI error but we don't want the same error from 100 machines. In all cases we only want to see one of each type of message: we don't want 10 messages saying the same disk has failed, and we don't want a message each time a broken SSI is hit. One approach to solving this is to aggregate multiple messages of the same type into one on each host, send the messages to a central server and then aggregate messages of the same kind into one overall event. SER can do this but it's awkward to use. Even after a couple of days of fiddling I had only rudimentary aggregations working and had to constantly look up the logic SER uses to correlate events. It's powerful but tricky stuff: I need something which my colleagues can pick up and use in the shortest possible time. SER rules don't meet that requirement. 3) Generating alerts How do we tell our admins when something interesting happens? Mail the group inbox? Inject into Nagios? So, how're you solving this problem? I don't expect an answer on a plate; I can work out the details myself but some high-level discussion on what is surely a common problem would be great. At the moment we're using a mishmash of cron jobs, syslog and who knows what else to find events. This isn't extensible, maintainable or flexible and as such we miss a lot of stuff we shouldn't. Updated: we're already using Nagios for monitoring which is great for detected down hosts/testing services/etc but less useful for scraping log files. I know there are log plugins for Nagios but I'm interested in something more scalable and hierarchical than per-host alerts.

  Read the article

• Hard drive after PCB swap strange stuff

  - by ramyy

  I’ve done a PCB swap to my HDD. The HDD model is: WD6400AAKS-00A7B2. The original PCB PN matches the new one (first three letter groups), though the cache mismatches (16MB original, 8MB new). The Hardware store that made the swap told me it was hard to do the swap, they have done firmware adaptation. I can see that this firmware version does not match the original, (01.03B01 original, 05.04E05 new). Still I can see that the serial number and model of the drive is correct, the hard drive appeared normal in the BIOS, all the partitions show and everything appears normal. I have encountered three things though, I have left the drive non operated for 2-3 weeks after the swap to avoid corrupting the data or anything else the new PCB might cause, until I buy a new drive and backup the data. I got a drive, and when I powered the old drive manually (I have a laptop, I use a normal desktop power supply and a USB/SATA connector), I heard the motor start and I could hear ticking as if the motor’s somehow struggling to start, and then the motor sound starts again then the ticking, and so on.. I tried powering again it happened again. The third time it started normally and I could see everything normally. I took the chance and copied all the data over to the new drive. When I was done, I powered off the drive (after more than 25 hours of continuous operation), tried to power it up again and it did so normally, and so are the times I powered it up later; but I got very suspicious now. What could be the problem here? And what happened new, it used to power normally after the swap directly? The second thing that happened is that I found size differences with some files; some include movies, songs, (.iso) files for games, and programs. I could find the size is the same, but size on disk is a little more on the new drive for these files. . I’ve tried some of those files (with size differences) they worked fine. They are not too much but still make you suspicious of the integrity of the data copied; one cannot try if all files are working for about (580 GB) worth of data. I tried copying these files on the same partition they exist of the old drive; they are the same in size as when copied to the new drive (allocation unit size not the issue). I took an image of a partition (sector by sector including empty ones) and when I explore it, these file sizes are equal to the original (old drive); I copy them anywhere else their size on disk, increases, i.e becomes equal to the ones I copy from the old drive itself anywhere. Why the size difference and can one trust the integrity of the data?? The third thing is that when I connect my new external USB HDD, the partitions of the old HDD unmount and then mount again. Connected are: (USB mouse + Old HDD) then external HDD. Why that happens?? Considering the following: I compared the SMART reports from after the swap directly and after the copying, no error readings or reallocated sectors where reported. Here they are: http://www.image-share.com/ijpg-1939-219.html I later ran both WD data life guard tests and they came out passed. I’m worried for this drive since I must be sure the data is fine and safe on the new one, and I will consider it backup for the new one, since you can’t trust anything anymore. I hope you can forgive me for the length of the post, but couldn’t ignore any of the details, this hard drive contains very important data to me and I have to deal with the situation with great care.

  Read the article

• How to save a ntfs partition which suddenly became empty

  - by SteveO

  One ntfs partition of my laptop was suddenly wiped out without any notice to me, when I rebooted from Windows 7 to Ubuntu 12.04 today. I am in need of help to save my files on that partition, which are important and unfortunately haven't been backed up yet. My laptop has two operating systems: Windows 7 and Ubuntu 12.04. with a ntfs partition shared between the two operating systems for storing some data files (109GB, about 97%of which has been used). I have almost always been using Ubuntu, but today I happened to have to work under Windows. Following is a record of what happened in the time order, numbering according to which operating system I was in at each stage. When I started into Windows 7, right before being able to log in, it took a while and two reboots to configure the Windows. I thought it was normal, since last time when I was using Windows two weeks ago, it took very long and several reboots to update Windows, since the last time I used Windows before then was in November last year. Then after finally being able to log in Windows 7, I installed Libre Office, MathType (I got it from http://dl.portablesoft.org/down/?id=2515, which I originally thought was a trial version, but later I learned was a cracked version and felt wrong. I made a copy of it at dropbox http://dl.dropbox.com/u/13029929/MathType_6.8_PortableSoft.rar, not for distributing it but to list it there just in case it will help to identify the problem), and MikTex. I then edited some .doc files in the ntfs partition under both Microsoft Office with MathType, and Libre Office. When I finished working under Windows and rebooted into Ubuntu, Ubuntu did some filesystem checking and reported that the ntfs partition was not able to be mounted. Then I rebooted again into Windows, and found that the ntfs partition had been emptied, i.e. all the data files were gone, and only one system file bootsqm.dat and one system directory System Volume Information were there, with their last updated time being the time when I first rebooted from Windows to Ubuntu (in fact, it is 4 hours in advanced than the actual time of that rebooting , see immediately below) Also I noticed that the time shown by Windows is not correct for my time zone (UTC-05:00) Eastern Time (US & Canada)), which is 4 hours in advance than the correct time (my current time is 3am, but the computer shows 7am). Same things happened when I rebooted into Ubuntu again: the ntfs has been emptied and left with only one Windows system file bootsqm.dat and one Windows system directory System Volume Information. the time shown by Ubuntu is 4 hours in advance than the correct time. I wonder what I can do to retrieve my data files back on the ntfs partition? If I am not able to do it myself, will some professionals be able to help me out? Thanks a lot! PS: I didn't think I did any thing that required emptying that partition. But there were quite some works I did during that stage right before the reboot from Windows to Ubuntu when the problem occured. Did I make any mis-operation?

  Read the article

• Hoster not fulfilling contract: how to get money back?

  - by plua

  For several years, we have as a small webdesign company rented a dedicated server at a large hosting provider. They had several support levels. When we signed up for this, we had very limited in-house knowledge about server maintenance, and were very worried about the security of our server. We therefore took one of the more expensive support packages. An important aspect in this were these claims: [PROVIDER] verifies the availability of the latest security updates and sends you a notification to see if you are interested to have them installed [PROVIDER] verifies the availability of the latest supported software updates and sends you a notification to see if you are interested to have them installed These items were clearly stated on their website as being part of the advantage of this package.; With not enough knowledge about installing and updating such software on a Linux server, we decided to go for this package. We paid a premium of $50 per month over the maintenance package that is next in line ($100 vs $50). Over the years, we have paid several thousand dollars for this service. Then came the moment that I learned more and more about server management. And I found out step by step that our server was horrendously outdated! We had an OS that was hardly updated, our anti-virus was not working because it needed certain more recent packages on the OS, and in general there were a whole bunch of security vulnerabilities and fixes that were lacking. Shocked, I wrote the provider. Turns out, they decided unilaterally that they would not send out any notifications to clients because clients would get too many e-mails. This is a quote from their explanation: [...] We have decided not to spam its clients with OS and security updates and only install them whenever asked by the client I was shocked! They had never mentioned that they would drop this service, and in fact the claims about updating their clients through e-mail was still on their website, after they apparently stopped doing this years ago! Upon finding this out, I requested they refund all that we have paid as a premium over the other package, and make it available as future credit with their own company. I thought this was a very reasonable request. However, they said they would only go back one year and provide credit for this one year. Mails went back and forth, but they were not willing to give credit for the whole period, which I felt I was entitled to. So ultimately I left the hosting company, and filed a complaint with the BBB a while ago. Now, I am not the kind of person who runs to a lawyer for any minor thing, but in this case I am really considering taking action. I have been paying for years for a service I did not receive (the premium package had a few other pluses, but we took it primarily for these two points, and I can prove that we did not use the other benefits). For our small company the hosting costs were a very large part of our budget, and I feel it is very unfair how this large provider just does not care about not fulfilling its obligations. So my question is: what action should I take? Is a lawyer the only next step, or are there other suggestions? And am I right here to claim this money, or are they right that there is some sort of statue of limitations on such claims? Any feedback is appreciated.

  Read the article

• From Binary to Data Structures

  - by Cédric Menzi

  Table of Contents Introduction PE file format and COFF header COFF file header BaseCoffReader Byte4ByteCoffReader UnsafeCoffReader ManagedCoffReader Conclusion History This article is also available on CodeProject Introduction Sometimes, you want to parse well-formed binary data and bring it into your objects to do some dirty stuff with it. In the Windows world most data structures are stored in special binary format. Either we call a WinApi function or we want to read from special files like images, spool files, executables or may be the previously announced Outlook Personal Folders File. Most specifications for these files can be found on the MSDN Libarary: Open Specification In my example, we are going to get the COFF (Common Object File Format) file header from a PE (Portable Executable). The exact specification can be found here: PECOFF PE file format and COFF header Before we start we need to know how this file is formatted. The following figure shows an overview of the Microsoft PE executable format. Source: Microsoft Our goal is to get the PE header. As we can see, the image starts with a MS-DOS 2.0 header with is not important for us. From the documentation we can read "...After the MS DOS stub, at the file offset specified at offset 0x3c, is a 4-byte...". With this information we know our reader has to jump to location 0x3c and read the offset to the signature. The signature is always 4 bytes that ensures that the image is a PE file. The signature is: PE\0\0. To prove this we first seek to the offset 0x3c, read if the file consist the signature. So we need to declare some constants, because we do not want magic numbers.   private const int PeSignatureOffsetLocation = 0x3c; private const int PeSignatureSize = 4; private const string PeSignatureContent = "PE";   Then a method for moving the reader to the correct location to read the offset of signature. With this method we always move the underlining Stream of the BinaryReader to the start location of the PE signature.   private void SeekToPeSignature(BinaryReader br) { // seek to the offset for the PE signagure br.BaseStream.Seek(PeSignatureOffsetLocation, SeekOrigin.Begin); // read the offset int offsetToPeSig = br.ReadInt32(); // seek to the start of the PE signature br.BaseStream.Seek(offsetToPeSig, SeekOrigin.Begin); }   Now, we can check if it is a valid PE image by reading of the next 4 byte contains the content PE.   private bool IsValidPeSignature(BinaryReader br) { // read 4 bytes to get the PE signature byte[] peSigBytes = br.ReadBytes(PeSignatureSize); // convert it to a string and trim \0 at the end of the content string peContent = Encoding.Default.GetString(peSigBytes).TrimEnd('\0'); // check if PE is in the content return peContent.Equals(PeSignatureContent); }   With this basic functionality we have a good base reader class to try the different methods of parsing the COFF file header. COFF file header The COFF header has the following structure: Offset Size Field 0 2 Machine 2 2 NumberOfSections 4 4 TimeDateStamp 8 4 PointerToSymbolTable 12 4 NumberOfSymbols 16 2 SizeOfOptionalHeader 18 2 Characteristics If we translate this table to code, we get something like this:   [StructLayout(LayoutKind.Sequential, CharSet = CharSet.Unicode)] public struct CoffHeader { public MachineType Machine; public ushort NumberOfSections; public uint TimeDateStamp; public uint PointerToSymbolTable; public uint NumberOfSymbols; public ushort SizeOfOptionalHeader; public Characteristic Characteristics; } BaseCoffReader All readers do the same thing, so we go to the patterns library in our head and see that Strategy pattern or Template method pattern is sticked out in the bookshelf. I have decided to take the template method pattern in this case, because the Parse() should handle the IO for all implementations and the concrete parsing should done in its derived classes.   public CoffHeader Parse() { using (var br = new BinaryReader(File.Open(_fileName, FileMode.Open, FileAccess.Read, FileShare.Read))) { SeekToPeSignature(br); if (!IsValidPeSignature(br)) { throw new BadImageFormatException(); } return ParseInternal(br); } } protected abstract CoffHeader ParseInternal(BinaryReader br);   First we open the BinaryReader, seek to the PE signature then we check if it contains a valid PE signature and rest is done by the derived implementations. Byte4ByteCoffReader The first solution is using the BinaryReader. It is the general way to get the data. We only need to know which order, which data-type and its size. If we read byte for byte we could comment out the first line in the CoffHeader structure, because we have control about the order of the member assignment.   protected override CoffHeader ParseInternal(BinaryReader br) { CoffHeader coff = new CoffHeader(); coff.Machine = (MachineType)br.ReadInt16(); coff.NumberOfSections = (ushort)br.ReadInt16(); coff.TimeDateStamp = br.ReadUInt32(); coff.PointerToSymbolTable = br.ReadUInt32(); coff.NumberOfSymbols = br.ReadUInt32(); coff.SizeOfOptionalHeader = (ushort)br.ReadInt16(); coff.Characteristics = (Characteristic)br.ReadInt16(); return coff; }   If the structure is as short as the COFF header here and the specification will never changed, there is probably no reason to change the strategy. But if a data-type will be changed, a new member will be added or ordering of member will be changed the maintenance costs of this method are very high. UnsafeCoffReader Another way to bring the data into this structure is using a "magically" unsafe trick. As above, we know the layout and order of the data structure. Now, we need the StructLayout attribute, because we have to ensure that the .NET Runtime allocates the structure in the same order as it is specified in the source code. We also need to enable "Allow unsafe code (/unsafe)" in the project's build properties. Then we need to add the following constructor to the CoffHeader structure.   [StructLayout(LayoutKind.Sequential, CharSet = CharSet.Unicode)] public struct CoffHeader { public CoffHeader(byte[] data) { unsafe { fixed (byte* packet = &data[0]) { this = *(CoffHeader*)packet; } } } }   The "magic" trick is in the statement: this = *(CoffHeader*)packet;. What happens here? We have a fixed size of data somewhere in the memory and because a struct in C# is a value-type, the assignment operator = copies the whole data of the structure and not only the reference. To fill the structure with data, we need to pass the data as bytes into the CoffHeader structure. This can be achieved by reading the exact size of the structure from the PE file.   protected override CoffHeader ParseInternal(BinaryReader br) { return new CoffHeader(br.ReadBytes(Marshal.SizeOf(typeof(CoffHeader)))); }   This solution is the fastest way to parse the data and bring it into the structure, but it is unsafe and it could introduce some security and stability risks. ManagedCoffReader In this solution we are using the same approach of the structure assignment as above. But we need to replace the unsafe part in the constructor with the following managed part:   [StructLayout(LayoutKind.Sequential, CharSet = CharSet.Unicode)] public struct CoffHeader { public CoffHeader(byte[] data) { IntPtr coffPtr = IntPtr.Zero; try { int size = Marshal.SizeOf(typeof(CoffHeader)); coffPtr = Marshal.AllocHGlobal(size); Marshal.Copy(data, 0, coffPtr, size); this = (CoffHeader)Marshal.PtrToStructure(coffPtr, typeof(CoffHeader)); } finally { Marshal.FreeHGlobal(coffPtr); } } }     Conclusion We saw that we can parse well-formed binary data to our data structures using different approaches. The first is probably the clearest way, because we know each member and its size and ordering and we have control about the reading the data for each member. But if add member or the structure is going change by some reason, we need to change the reader. The two other solutions use the approach of the structure assignment. In the unsafe implementation we need to compile the project with the /unsafe option. We increase the performance, but we get some security risks.

  Read the article

• Content Management for WebCenter Installation Guide

  - by Gary Niu

  Overvew As we known, there are two way to install Content Management for WebCenter. One way is install it by WebCenter installer wizard, another way is to install it use their own installer. This guide is for the later one. For SSO purpose, I also mentioned how to config OID identity store for Content Management for WebCenter. Content Management for WebCenter( 10.1.3.5.1) Oracle Enterprise Linux R5U4 Basic Installation -bash-3.2$ ./setup.sh Please select your locale from the list.           1. Chinese-Simplified           2. Chinese-Traditional           3. Deutsch          *4. English-US           5. English-UK           6. Español           7. Français           8. Italiano           9. Japanese          10. Korean          11. Nederlands          12. Português-Brazil Choice? Throughout the install, when entering a text value, you can press Enter to accept the default that appears between square brackets ([]). When selecting from a list, you can select the choice followed by an asterisk by pressing Enter. Select installation type from the list.         *1. Install new server          2. Update a server Choice? Content Server Installation Directory Please enter the full pathname to the installation directory. Content Server Core Folder [/oracle/ucm/server]:/opt/oracle/ucm/server Create Directory         *1. yes          2. no Choice? Java virtual machine         *1. Sun Java 1.5.0_11 JDK          2. Specify a custom Java virtual machine Choice? Installing with Java version 1.5.0_11. Enter the location of the native file repository. This directory contains the native files checked in by contributors. Content Server Native Vault Folder [/opt/oracle/ucm/server/vault/]: Create Directory         *1. yes          2. no Choice? Enter the location of the web-viewable file repository. This directory contains files that can be accessed through the web server. Content Server Weblayout Folder [/opt/oracle/ucm/server/weblayout/]: Create Directory         *1. yes          2. no Choice? This server can be configured to manage its own authentication or to allow another master to act as an authentication proxy. Configure this server as a master or proxied server.         *1. Configure as a master server.          2. Configure as server proxied by a local master server. Choice? During installation, an admin server can be installed and configured to manage this server. If there is already an admin server on this system, you can have the installer configure it to administrate this server instead. Select admin server configuration.         *1. Install an admin server to manage this server.          2. Configure an existing admin server to manage this server.          3. Don't configure an admin server. Choice? Enter the location of an executable to start your web browser. This browser will be used to display the online help. Web Browser Path [/usr/bin/firefox]: Content Server System locale           1. Chinese-Simplified           2. Chinese-Traditional           3. Deutsch          *4. English-US           5. English-UK           6. Español           7. Français           8. Italiano           9. Japanese          10. Korean          11. Nederlands          12. Português-Brazil Choice? Please select the region for your timezone from the list.         *1. Use the timezone setting for your operating system          2. Pacific          3. America          4. Atlantic          5. Europe          6. Africa          7. Asia          8. Indian          9. Australia Choice? Please enter the port number that will be used to connect to the Content Server. This port must be otherwise unused. Content Server Port [4444]: Please enter the port number that will be used to connect to the Admin Server. This port must be otherwise unused. Admin Server Port [4440]: Enter a security filter for the server port. Hosts which are allowed to communicate directly with the server port may access any resources managed by the server. Insure that hosts which need access are included in the filter. See the installation guide for more details. Incoming connection address filter [127.0.0.1]:*.*.*.* *** Content Server URL Prefix The URL prefix specified here is used when generating HTML pages that refer to the contents of the weblayout directory within the installation. This prefix must be mapped in the web server Additional Document Directories section of the Content Management administration menu to the physical location of the weblayout directory. For example, "/idc/" would be used in your installation to refer to the URL http://ucm.company.com/idc which would be mapped in the web server to the physical location /oracle/ucm/server/weblayout. Web Server Relative Root [/idc/]: Enter the name of the local mail server. The server will contact this system to deliver email. Company Mail Server [mail]: Enter the e-mail address for the system administrator. Administrator E-Mail Address [sysadmin@mail]: *** Web Server Address Many generated HTML pages refer to the web server you are using. The address specified here will be used when generating those pages. The address should include the host and domain name in most cases. If your webserver is running on a port other than 80, append a colon and the port number. Examples: www.company.com, ucm.company.com:90 Web Server HTTP Address [yekki]:yekki.cn.oracle.com:7777 Enter the name for this instance. This name should be unique across your entire enterprise. It may not contain characters other than letters, numbers, and underscores. Server Instance Name [idc]: Enter a short label for this instance. This label is used on web pages to identify this instance. It should be less than 12 characters long. Server Instance Label [idc]: Enter a long description for this instance. Server Description [Content Server idc]: Web Server         *1. Apache          2. Sun ONE          3. Configure manually Choice? Please select a database from the list below to use with the Content Server. Content Server Database         *1. Oracle          2. Microsoft SQL Server 2005          3. Microsoft SQL Server 2000          4. Sybase          5. DB2          6. Custom JDBC settings          7. Skip database configuration Choice? Manually configure JDBC settings for this database          1. yes         *2. no Choice? Oracle Server Hostname [localhost]: Oracle Listener Port Number [1521]: *** Database User ID The user name is used to log into the database used by the content server. Oracle User [user]:YEKKI_OCSERVER *** Database Password The password is used to log into the database used by the content server. Oracle Password []:oracle Oracle Instance Name [ORACLE]:orcl Configure the JVM to find the JDBC driver in a specific jar file          1. yes         *2. no Choice? The installer can attempt to create the database tables or you can manually create them. If you choose to manually create the tables, you should create them now. Attempt to create database tables          1. yes         *2. no Choice? Select components to install.          1. ContentFolios: Collect related items in folios          2. Folders_g: Organize content into hierarchical folders          3. LinkManager8: Hypertext link management support          4. OracleTextSearch: External Oracle 11g database as search indexer support          5. ThreadedDiscussions: Threaded discussion management Enter numbers separated by commas to toggle, 0 to unselect all, F to finish: 1,2,3,4,5         *1. ContentFolios: Collect related items in folios         *2. Folders_g: Organize content into hierarchical folders         *3. LinkManager8: Hypertext link management support         *4. OracleTextSearch: External Oracle 11g database as search indexer support         *5. ThreadedDiscussions: Threaded discussion management Enter numbers separated by commas to toggle, 0 to unselect all, F to finish: F Checking configuration. . . Configuration OK. Review install settings. . . Content Server Core Folder: /opt/oracle/ucm/server Java virtual machine: Sun Java 1.5.0_11 JDK Content Server Native Vault Folder: /opt/oracle/ucm/server/vault/ Content Server Weblayout Folder: /opt/oracle/ucm/server/weblayout/ Proxy authentication through another server: no Install admin server: yes Web Browser Path: /usr/bin/firefox Content Server System locale: English-US Content Server Port: 4444 Admin Server Port: 4440 Incoming connection address filter: *.*.*.* Web Server Relative Root: /idc/ Company Mail Server: mail Administrator E-Mail Address: sysadmin@mail Web Server HTTP Address: yekki.cn.oracle.com:7777 Server Instance Name: idc Server Instance Label: idc Server Description: Content Server idc Web Server: Apache Content Server Database: Oracle Manually configure JDBC settings for this database: false Oracle Server Hostname: localhost Oracle Listener Port Number: 1521 Oracle User: YEKKI_OCSERVER Oracle Password: 6GP1gBgzSyKa4JW10U8UqqPznr/lzkNn/Ojf6M8GJ8I= Oracle Instance Name: orcl Configure the JVM to find the JDBC driver in a specific jar file: false Attempt to create database tables: no Components: ContentFolios,Folders_g,LinkManager8,OracleTextSearch,ThreadedDiscussions Proceed with install         *1. Proceed          2. Change configuration          3. Recheck the configuration          4. Abort installation Choice? Finished install type Install with warnings at 4/2/10 12:32 AM. Run Scripts -bash-3.2$ ./wc_contentserverconfig.sh /opt/oracle/ucm/server /mnt/hgfs/SOFTWARE/ofm_ucm_generic_10.1.3.5.1_disk1_1of1/ContentServer/webcenter-conf Installing '/mnt/hgfs/SOFTWARE/ofm_ucm_generic_10.1.3.5.1_disk1_1of1/ContentServer/webcenter-conf/CS10gR35UpdateBundle.zip' Service 'DELETE_DOC' Extended Service 'DELETE_BYREV_REVISION' Extended Installing '/mnt/hgfs/SOFTWARE/ofm_ucm_generic_10.1.3.5.1_disk1_1of1/ContentServer/webcenter-conf/ContentAccess/ContentAccess-linux.zip' (internal)      04.02 00:40:38.019      main    updateDocMetaDefinitionV11: adding decimal column Installing '/opt/oracle/ucm/server/custom/CS10gR35UpdateBundle/extras/Folders_g.zip' Installing '/opt/oracle/ucm/server/custom/CS10gR35UpdateBundle/extras/FusionLibraries.zip' Installing '/opt/oracle/ucm/server/custom/CS10gR35UpdateBundle/extras/JpsUserProvider.zip' Installing '/mnt/hgfs/SOFTWARE/ofm_ucm_generic_10.1.3.5.1_disk1_1of1/ContentServer/webcenter-conf/WcConfigure.zip' Apr 2, 2010 12:41:24 AM oracle.security.jps.internal.core.util.JpsConfigUtil getPasswordCredential WARNING: A password credential is expected; instead found . Apr 2, 2010 12:41:24 AM oracle.security.jps.internal.idstore.util.IdentityStoreUtil getUnamePwdFromCredStore WARNING: The credential with map JPS and key ldap.credential does not exist. Apr 2, 2010 12:41:27 AM oracle.security.jps.internal.core.util.JpsConfigUtil getPasswordCredential WARNING: A password credential is expected; instead found . Apr 2, 2010 12:41:27 AM oracle.security.jps.internal.idstore.util.IdentityStoreUtil getUnamePwdFromCredStore WARNING: The credential with map JPS and key ldap.credential does not exist. Apr 2, 2010 12:41:28 AM oracle.security.jps.internal.core.util.JpsConfigUtil getPasswordCredential WARNING: A password credential is expected; instead found . Apr 2, 2010 12:41:28 AM oracle.security.jps.internal.idstore.util.IdentityStoreUtil getUnamePwdFromCredStore WARNING: The credential with map JPS and key ldap.credential does not exist. Restart Content Server to apply updates. Configuring Apache Web Server append the following lines at httpd.conf: include "/opt/oracle/ucm/server/data/users/apache22/apache.conf" Configuring the Identity Store( Optional ) 1.  Stop Oracle Content Server and the Admin Server 2.  Update the Oracle Content Server's JPS configuration file, jps-config.xml: a. add a service instance <serviceInstance provider="idstore.ldap.provider" name="idstore.oid"> <property name="subscriber.name" value="dc=cn,dc=oracle,dc=com"></property> <property name="idstore.type" value="OID"></property> <property name="security.principal.key" value="ldap.credential"></property> <property name="security.principal.alias" value="JPS"></property> <property name="ldap.url" value="ldap://yekki.cn.oracle.com:3060"></property> <extendedProperty> <name>user.search.bases</name> <values> <value>cn=users,dc=cn,dc=oracle,dc=com</value> </values> </extendedProperty> <extendedProperty> <name>group.search.bases</name> <values> <value>cn=groups,dc=cn,dc=oracle,dc=com</value> </values> </extendedProperty> <property name="username.attr" value="uid"></property> <property name="user.login.attr" value="uid"></property> <property name="groupname.attr" value="cn"></property> </serviceInstance> b. Ensure that the <jpsContext> entry in the jps-config.xml file refers to the new serviceInstance, that is, idstore.oid and not idstore.ldap: <jpsContext name="default"> <serviceInstanceRef ref="idstore.oid"/> 3. Run the new script to setup the credentials for idstore.oid in the credential store: cd CONTENT_SERVER_HOME/custom/FusionLibraries/tools -bash-3.2$ ./run_credtool.sh Buildfile: ./../tools/credtool.xml     [input] skipping input as property action has already been set.     [input] Alias: [JPS]     [input] Key: [ldap.credential]     [input] User Name: cn=orcladmin     [input] Password: welcome1     [input] JPS Config: [/opt/oracle/ucm/server/custom/FusionLibraries/tools/../../../config/jps-config.xml] manage-creds:      [echo] @@@ Help: run 'ant manage-creds' command to see the detailed usage      [java] Using default context in /opt/oracle/ucm/server/custom/FusionLibraries/tools/../../../config/jps-config.xml file for credential store.      [java] Credential store location : /opt/oracle/ucm/server/config      [java] Credential with map JPS key ldap.credential stored successfully!      [java]      [java]      [java]     Credential for map JPS and key ldap.credential is:      [java]             PasswordCredential name : cn=orcladmin      [java]             PasswordCredential password : welcome1 BUILD SUCCESSFUL Total time: 1 minute 27 seconds Testing 1. acces http://yekki.cn.oracle.com:7777/idc 2. login in with OID user, for example: orcladmin/welcome1 3. make sure your JpsUserProvider status is "good"

  Read the article

• Add keyboard languages to XP, Vista, and Windows 7

  - by Matthew Guay

  Do you regularly need to type in multiple languages in Windows?  Here we’ll show you the easy way to add and change input languages to your keyboard in XP, Vista, and Windows 7. Windows Vista and 7 come preinstalled with support for viewing a wide variety of languages, so adding an input language is fairly simply.  Adding an input language is slightly more difficult in XP, and requires installing additional files if you need an Asian or Complex script language.  First we show how to add an input language in Windows Vista and 7; it’s basically the same in both versions.  Then, we show how to add a language to XP, and also how to add Complex Script support.  Please note that this is only for adding an input language, which will allow you to type in the language you select.  This does not change your user interface language. Change keyboard language in Windows 7 and Vista It is fairly simple to add or change a keyboard language in Windows 7 or Vista.  In Windows 7, enter “keyboard language” in the Start menu search box, and select “Change keyboards or other input methods”. In Windows Vista, open Control Panel and enter “input language” in the search box and select “Change keyboards or other input methods”.  This also works in Windows 7. Now, click Change Keyboards to add another keyboard language or change your default one. Our default input language is US English, and our default keyboard is the US keyboard layout.  Click Add to insert another input language while still leaving your default input language installed. Here we selected the standard Thai keyboard language (Thai Kedmanee), but you can select any language you want.  Windows offers almost any language you can imagine, so just look for the language you want, select it, and click Ok. Alternately, if you want, you can click Preview to see your layout choice before accepting it.  This is only the default characters, not ones that will be activated with Shift or other keys (many Asian languages use many more characters than English, and require the use of Shift and other keys to access them all).  Once your finished previewing, click close and then press Ok on the previous dialog. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and get more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Also, you can now change the default input language from the top menu.  This is the language that your keyboard will start with when you boot your computer.  So, if you mainly use English but also use another language, usually it is best to leave English as your default input language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. Some complex languages, such as Chinese, may have extra buttons to change input modes to accommodate their large alphabet. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and select the “Advanced Key Settings” tab.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Also, the On-Screen keyboard will display the correct keyboard language (here the keyboard is displaying Thai), which can be a helpful reference if your physical keyboard doesn’t have your preferred input language printed on it.  To open this, simply enter “On-Screen keyboard” in the start menu search, or click All Programs>Accessories>On-Screen keyboard. Change keyboard language in Windows XP The process for changing the keyboard language in Windows XP is slightly different.  Open Control Panel, and select “Date, Time, Language, and Regional Options”.   Select “Add other languages”. Now, click Details to add another language.  XP does not include support for Asian and complex languages by default, so if you need to add one of those languages we have details for that below. Click Add to add an input language. Select your desired language from the list, and choose your desired keyboard layout if your language offers multiple layouts.  Here we selected Canadian French with the default layout. Now you will see both of your keyboard languages in the Installed services box.  You can click Add to go back and add more, or move your selected language up or down (to change its priority), or simply click Apply to add the new language. Once you’ve pressed Apply or Ok, you will see a new icon beside your system tray with the initials of your default input language. If you click it, you can switch between input languages.  Alternately you can switch input languages by pressing Alt+Shift on your keyboard. If you would like to change the keyboard shortcut for changing languages, go back to the Input Languages dialog, and click the “Key Settings” button on the bottom of the dialog.  Here you can change settings for Caps Lock and change or add key sequences to change between languages. Add support to XP for Asian and Complex script languages Windows XP does not include support for Asian and Complex script languages by default, but you can easily add them to your computer.  This is useful if you wish to type in one of these languages, or simply want to read text written in these languages, since XP will not display these languages correctly if they are not installed.  If you wish to install Chinese, Japanese, and/or Korean, check the “Install files for East Asian languages” box.  Or, if you need to install a complex script language (including Arabic, Armenian, Georgian, Hebrew, the Indic languages, Thai, and Vietnamese), check the “Install files for complex script and right-to-left languages” box.   Choosing either of these options will open a prompt reminding you that this option will take up more disk space.  Support for complex languages will require around 10Mb of hard drive space, but East Asian language support may require 230 Mb or more free disk space.  Click Ok, and click apply to install your language files. You may have to insert your XP CD into your CD drive to install these files.  Insert the disk, and then click Ok. Windows will automatically copy the files, including fonts for these languages… …and then will ask you to reboot your computer to finalize the settings.  Click Yes, and then reopen the “Add other languages” dialog when your computer is rebooted, and add a language as before.     Now you can add Complex and/or Asian languages to XP, just as above.  Here is the XP taskbar language selector with Thai installed. Conclusion Unfortunately we haven’t found a way to add Asian and complex languages in XP without having an XP disc. If you know of a way, let us know in the comments. (No downloading the XP disc from torrent site answers please) Adding an input language is very important for bilingual individuals, and can also be useful if you simply need to occasionally view Asian or Complex languages in XP.  And by following the correct instructions for your version of Windows, it should be very easy to add, change, and remove input languages. Similar Articles Productive Geek Tips Show Keyboard Shortcut Access Keys in Windows VistaKeyboard Ninja: 21 Keyboard Shortcut ArticlesAnother Desktop Cube for Windows XP/VistaThe "Up" Keyboard Shortcut for Windows 7 or Vista ExplorerWhat is ctfmon.exe And Why Is It Running? TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Windows 7 Phone Database – Querying with Views and Filters

  - by SeanMcAlinden

  I’ve just added a feature to Rapid Repository to greatly improve how the Windows 7 Phone Database is queried for performance (This is in the trunk not in Release V1.0). The main concept behind it is to create a View Model class which would have only the minimum data you need for a page. This View Model is then stored and retrieved rather than the whole list of entities. Another feature of the views is that they can be pre-filtered to even further improve performance when querying. You can download the source from the Microsoft Codeplex site http://rapidrepository.codeplex.com/. Setting up a view Lets say you have an entity that stores lots of data about a game result for example: GameScore entity public class GameScore : IRapidEntity {     public Guid Id { get; set; }     public string GamerId {get;set;}     public string Name { get; set; }     public Double Score { get; set; }     public Byte[] ThumbnailAvatar { get; set; }     public DateTime DateAdded { get; set; } }   On your page you want to display a list of scores but you only want to display the score and the date added, you create a View Model for displaying just those properties. GameScoreView public class GameScoreView : IRapidView {     public Guid Id { get; set; }     public Double Score { get; set; }     public DateTime DateAdded { get; set; } }   Now you have the view model, the first thing to do is set up the view at application start up. This is done using the following syntax. View Setup public MainPage() {     RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score }); } As you can see, using a little bit of lambda syntax, you put in the code for constructing a single view, this is used internally for mapping an entity to a view. *Note* you do not need to map the Id property, this is done automatically, a view model id will always be the same as it’s corresponding entity.   Adding Filters One of the cool features of the view is that you can add filters to limit the amount of data stored in the view, this will dramatically improve performance. You can add multiple filters using the fluent syntax if required. In this example, lets say that you will only ever show the scores for the last 10 days, you could add a filter like the following: Add single filter public MainPage() {     RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score })         .AddFilter(x => x.DateAdded > DateTime.Now.AddDays(-10)); } If you wanted to further limit the data, you could also say only scores above 100: Add multiple filters public MainPage() {     RapidRepository<GameScore>.AddView<GameScoreView>(x => new GameScoreView { DateAdded = x.DateAdded, Score = x.Score })         .AddFilter(x => x.DateAdded > DateTime.Now.AddDays(-10))         .AddFilter(x => x.Score > 100); }   Querying the view model So the important part is how to query the data. This is done using the repository, there is a method called Query which accepts the type of view as a generic parameter (you can have multiple View Model types per entity type) You can either use the result of the query method directly or perform further querying on the result is required. Querying the View public void DisplayScores() {     RapidRepository<GameScore> repository = new RapidRepository<GameScore>();     List<GameScoreView> scores = repository.Query<GameScoreView>();       // display logic } Further Filtering public void TodaysScores() {     RapidRepository<GameScore> repository = new RapidRepository<GameScore>();     List<GameScoreView> todaysScores = repository.Query<GameScoreView>().Where(x => x.DateAdded > DateTime.Now.AddDays(-1)).ToList();       // display logic }   Retrieving the actual entity Retrieving the actual entity can be done easily by using the GetById method on the repository. Say for example you allow the user to click on a specific score to get further information, you can use the Id populated in the returned View Model GameScoreView and use it directly on the repository to retrieve the full entity. Get Full Entity public void GetFullEntity(Guid gameScoreViewId) {     RapidRepository<GameScore> repository = new RapidRepository<GameScore>();     GameScore fullEntity = repository.GetById(gameScoreViewId);       // display logic } Synchronising The View If you are upgrading from Rapid Repository V1.0 and are likely to have data in the repository already, you will need to perform a synchronisation to ensure the views and entities are fully in sync. You can either do this as a one off during the application upgrade or if you are a little more cautious, you could run this at each application start up. Synchronise the view public void MyUpgradeTasks() {     RapidRepository<GameScore>.SynchroniseView<GameScoreView>(); } It’s worth noting that in normal operation, the view keeps itself in sync with the entities so this is only really required if you are upgrading from V1.0 to V2.0 when it gets released shortly.   Summary I really hope you like this feature, it will be great for performance and I believe supports good practice by promoting the use of View Models for specific pages. I’m hoping to produce a beta for this over the next few days, I just want to add some more tests and hopefully iron out any bugs. I would really appreciate any thoughts on this feature and would really love to know of any bugs you find. You can download the source from the following : http://rapidrepository.codeplex.com/ Kind Regards, Sean McAlinden.

  Read the article

< Previous Page | 416 417 418 419 420 421 422 423 424 425 426 427  | Next Page >