Search Results

Search found 22893 results on 916 pages for 'client scripting'.

Page 423/916 | < Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• LogMeIn Hamachi for Linux

  - by tlunter

  So far most of my work using LogMeIn Hamachi has been from either a Mac OS X or Windows system to Windows or a Linux Computer. Recently I purchased a mini computer and have been running Ubuntu Server on it, as my little server. I knew LogMeIn had a Linux client that is command line only, but I often do all my work via command line anyway, so that wasn't an issue. I added my user to the correct local file so that I could run the hamachi daemon without sudo, and was able to connect to LogMeIn's service. I decided to set up my Linux server as a git server as well, and set it up correctly. The thing is, the server is behind my schools firewall and I need to use hamachi to get around that. Since most of the time I was using either Mac or Windows, I never had an issue sshing onto any of my computers since LogMeIn is fully featured for these OSs. From Linux (Arch) though, it seems like the client cannot correctly route to the LogMeIn IPs. I know from Windows I can connect to the Linux computers, both of them. From Linux (Arch) though, I can't connect to my Mac, Windows, or Linux server. It keeps just dropping the connection. I was wondering if there was some configuration that I would need to make for this to work. I understand that it is most likely going to be a static configuration since I assume it has to do with the computer not understanding that 5.*.*.* actually refers to another IP:Port. Has anyone had any experience getting this to work?

  Read the article

• IIS FTP error: 426 Connection closed; transfer aborted.

  - by Jiaoziren

  Hi, I have an IIS FTP set up on Windows 2003 SP2 (S1). Everyday in the early morning, a script on another server (S2) will run and initiate FTP transfer of pulling log files from S1 to S2. The FTP client we're using is built-in FTP.exe in Windows 2000 on S2. Recently we replaced S1 with a new server however we kept the IP address. There are multiple IP addresses on new S1. Ever since the new S1 was in place, the '426 Connection closed; transfer aborted.' errors haven been occuring randomly. The log indicated that the transfer started ok however the file cannot be transferred completely, as per log below: mget access*.log 200 Type set to A. 200 PORT command successful. 150 Opening ASCII mode data connection for access02232010.log(205777167 bytes). 426 Connection closed; transfer aborted. ftp: 20454832 bytes received in 283.95Seconds 72.04Kbytes/sec. The firewall monitor suggested that the connection was setup in passive mode however I've been told that MS FTP.exe doesn't support passive mode. Though I can see the response of 'entering passive mode' from server when typing in 'quote pasv'. My network admin has told me to try the transfer in active mode however I don't know how to open active mode on client side. It's getting really frustrating. Wish someone here has the right knowledge/experience could shed me a light. Cheers.

  Read the article

• Authenticating Active Directory Users to Mac OS X Mavericks Server L2TP VPN Service

  - by dean

  We have a Windows Server 2012 Active Directory Infrastructure that consists of two domain controllers. Bound to the Active Directory Domain is a Mac OS X Mavericks Server 10.9.3. The server runs Profile Manager and VPN Services. My Active Directory users are able to authenticate to the Profile Manager, but not the VPN. I have found several threads on other forums of other users reporting similar issues, here is just one of many references: https://discussions.apple.com/thread/5174619 It appears as though the issue is related to a CHAP authentication failure. Can anyone suggest what next troubleshooting steps I might take? Is there a way to liberalize the authentication mechanism to include MSCHAP? Here is an excerpt of the transaction from the logs. Please note the domain has been changed to example.com. Jun 6 15:25:03 profile-manager.example.com vpnd[10317]: Incoming call... Address given to client = 192.168.55.217 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: publish_entry SCDSet() failed: Success! Jun 6 15:25:03 --- last message repeated 2 times --- Jun 6 15:25:03 profile-manager.example.com pppd[10677]: pppd 2.4.2 (Apple version 727.90.1) started by root, uid 0 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: L2TP incoming call in progress from '108.46.112.181'... Jun 6 15:25:03 profile-manager.example.com racoon[257]: pfkey DELETE received: ESP 192.168.55.12[4500]->108.46.112.181[4500] spi=25137226(0x17f904a) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP connection established. Jun 6 15:25:04 profile-manager kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 0) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connect: ppp0 <--> socket[34:18] Jun 6 15:25:04 profile-manager.example.com pppd[10677]: CHAP peer authentication failed for alex Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connection terminated. Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnecting... Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnected Jun 6 15:25:04 profile-manager.example.com vpnd[10317]: --> Client with address = 192.168.55.217 has hung up

  Read the article

• Googlebot repeatedly looks for files that aren't on my server

  - by John at CashCommons

  I'm hosting a site for a volunteer organization. I've moved the site to WordPress, but it wasn't always that way. I suspect at one point it was hacked badly. My Apache error log file has grown to 122 kB in just the past 18 hours. The large majority of the errors logged are of this form -- it's repeated hundreds of times today alone in my log files: [Mon Nov 12 18:29:27 2012] [error] [client xx.xxx.xx.xxx] File does not exist: /home/*******/public_html/*******.org/calendar.php [Mon Nov 12 18:29:27 2012] [error] [client xx.xxx.xx.xxx] File does not exist: /home/*******/public_html/*******.org/404.shtml (I verified that xx.xxx.xx.xxx was a Google server.) I suspect there was a security hole somewhere before, likely in calendar.php, that was exploited. The files don't exist anymore, but there may be many backlinks that exist that reference here, hence why googlebot is so interested in crawling them. How do I fix this gracefully? I still would like Google to index the site. I just want to tell it somehow not to look for these files anymore.

  Read the article

• Configuring OS X L2TP VPN to use Certificate for IPSEC layer instead of Pre Shared Key

  - by Matthew Savage

  I'm trying to setup a L2TP VPN on an OS X Snow Leopard Server setup, and have had success using a pre-shared key, however I would rather not rely on a simple string, and use a certificate instead. Setting this up on the server side is seemingly easy, you simply select a certificate you have generated from the list, and hit apply, however when I try to use the certificate on the client side it fails. I have exported the certificate into a P12 file, and then transferred to the client, and imported into the login keychain, however when I try to choose the certificate (from Network preferences, clicking Authentication Settings, then selecting Certificate and pressing Select) I am shown the following error: No machine certificates found Certificate authentication cannot be used because your keychain does not contain any suitable certificates. Use Keychain Access to import the certificate into your keychain. If you do not have the certificates required for authentication, contact your network administrator. Unfortunately even when I try to generate a certificate where I override the defaults, ensure the DNS name etc are set properly this doesn't change. When I select Certificate Authentication for the User Auth, and click Select the certificate for the server shows up there, but obviously this isn't where I need it to be available.

  Read the article

• Mysql Cluster not working on Ubuntu

  - by user53864

  I am unable to setup MySQL Cluster on ubuntu servers. As a starting point I started from the link but I am not successful and the tar ball version I download is 6.3.45. As I wanted to test the mysql cluster, the Data node and SQL node are same but sql never appeared as connected in management node console and it looks like below. [ndbd(NDB)] 2 node(s) id=2 @192.168.1.107 (Version: version number, Nodegroup: 0, Master) id=3 @192.168.1.108 (Version: version number, Nodegroup: 0) [ndb_mgmd(MGM)] 1 node(s) id=1 @192.168.1.105 (Version: version number) [mysqld(API)] 2 node(s) id=4 (not connected, accepting connect from 192.168.1.107) id=5 (not connected, accepting connect from 192.168.1.108) On all the 3 machines mysql-server & client(apt-get install mysql-server mysql-client) were already installed and I completely stopped and also removed them at the system start up. Now the mysqld is from extracted cluster tar ball(/usr/local/mysql/support-files/mysql.server). As for testing, I created a test database on both the data nodes but the tables are also not syncing on other node. I checked many links, configurations are remained similar in all the links but somewhere it's going wrong. Anymore extra package is required?, Could anyone help me here..?. I am trying this for past 3 days... Thank you!

  Read the article

• How to auto-cc a system email account any time a user creates an appointment

  - by Ferdy

  I will not bother explaining my full architecture or reasons for wanting this in order to keep this question short: Is it possible to auto-cc a certain email account any time a Exchange user creates an appointment or meeting in his own calendar? Is it possible using rules? Our Exchange 2007 server is outsourced, I cannot change the configuration or install plugins server-side Preferably, it still should work server-side, because users may use the Outlook client but also Outlook Web Access Is there any other way, perhaps using group policies? My conclusion so far is that the only viable way to accomplish this is to build an Outlook add-on. The problem there is that it will need to be managed for thousands of desktop users and that the add-on will not work when using another client (OWA, mobile). An alternative architecture could be to pull the information from the user's calendar on a scheduled basis. Given that we are talking about a lot of users, scalability is a major issue, this has also been confirmed by Microsoft. Can you confirm that my thinking is correct or do you have any other solutions?

  Read the article

• VMware ARP/Mac Networking

  - by Ross Wilson

  Hi Guys, I am very interested in how VMware networking works. I have scoured the VMware website and read their data sheets, this has given me some basic knowledge. I now have some questions. Lets assume that we have a physical server running the VMware hypervisor. The physical server is running a Virtual Machine. The physical box has one physical NIC. The NIC is connected to a switch, as so is a desktop client. Now, this is where my first question lies. The VM has an IP address: 192.168.1.1. How do desktop clients on the network communicate with this VM? So, the client pings 192.168.1.1. The ping packet is sent to the switch. The switch checks its MAC address table and sees that 192.168.1.1 is associated with the MAC address of the physical NIC. Correct? I then assume that the ping packet is sent to the server's physical NIC, where the hypervisor routes the packet to the VM thats using 192.168.1.1? Please could you give me a run down as to how VM networking works? Many thanks, Ross

  Read the article

• Windows 7 - Windows XP - sharing - why isn't working?

  - by durumdara

  Hi! This is seems to be "hardware" and not "software" / "programming" question, but I need to use this share in my programs, so it is "close to programming". We had an XP based wireless network. The server is XP Professional, the clients are XP Home (Notebooks). This was working well with folder sharing (with user rights, not simple share). Then we replaced the one of the notebook with Win7/X64 notebook. First time this can reach the server, and the another client too. Later I went to another sites, and connect to another servers, another networks. And then, when I return to this network, I saw that I cannot connect to this server. Nothing of resources I see, and when try to dbl click on this computer, I got login window, where I can write anything, never I can login... The interesting part, that: Another XP home can see the server, can login as quest, or with other user. The server can see the XP home notebook. The Win7 can see the notebook's shared folders, and XP home can see the Win7 shared folders. The server can see the Win7 folders, BUT: the Win7 cannot see the server folders. Cannot see the resources too... The Win7 is in "work networking group", the group name is not mshome. I tried everything on the server, I tried to remove MS client, restore it with simple sharing, set guest password, etc., but I lost the possibilities to access this server from Win7. Does anyone have any idea what I need to see, what I need to set to access these resource - to use them in my programs? Thanks for every info, link: dd

  Read the article

• Mirror a Dropbox repository in Sharepoint and restrict access

  - by Dan Robson

  I'm looking for an elegant way to solve the following problem: My development team uses Dropbox for sharing documents amongst our immediate group. We'd like to put some of those documents into a SharePoint repository for the larger group to be able to access, as granting Dropbox access to the group at large is not ideal. However, we'd like to continue to be able to propagate changes to the SharePoint site simply by updating the files in Dropbox on our local client machines, and also vice versa - users granted access on SharePoint that update files in that workspace should be able to save their files and the changes should appear automatically on our client PC's. I've already done the organization of the folders so that in Dropbox, there exists a SharePoint folder that looks something like this: SharePoint ----Team --------Restricted Access Folders ----Organization --------Open Access Folders The Dropbox master account and the SharePoint master account are both set up on my file server. Unfortunately, Dropbox doesn't seem to allow syncing of folders anywhere above the \Dropbox\ part of the file system's hierarchy - or all I would have to do is find where the Sharepoint repository is maintained locally, and I'd be golden. So it seems I have to do some sort of 2-way synchronization between the Dropbox folder on the file server and the SharePoint folder on the file server. I messed around with Microsoft SyncToy, but it seems to be lacking in the area of real-time updating - and as much as I love rsync, I've had nothing but bad luck with it on Windows, and again, it has to be kicked off manually or through Task Scheduler - and I just have a feeling if I go down that route, it's only a matter of time before I get conflicts all over the place in either Dropbox, SharePoint, or both. I really want something that's going to watch both folders, and when one item changes, the other automatically updates in "real-time". It's quite possible I'm going down the entirely wrong route, which is why I'm asking the question. For simplicity's sake, I'll restate the goal: To be able to update Dropbox and have it viewable on the SharePoint site, or to update the SharePoint site and have it viewable in Dropbox. And since I'm a SharePoint noob, I'll also need help hiding the "Team" subfolder from everyone not in a specific group in AD.

  Read the article

• Apache, suexec, PHP, suPHP

  - by Chris_K

  While I'm quite comfortable as a Linux user, my Linux Admin-fu is a bit weak. Thus, I'm here looking for guidance with a CentOS server I'm about to build. I need to setup an Apache2 web server for a few of our clients. I want each client's web content to be under their home directory (USERDIR in apache.conf, right?) for the static HTML sites. I want Apache to run as the client (suexec?). Some of their stuff will be PHP apps and I'm under the impression I'll want to look at suphp as well then. So basically I want to look like a small version of a shared web hosting company. Considering how common those are I thought I'd easily find a nice current How-To guide on setting this all up but so far I've had very little luck. I suspect my search words are off. So the questions (feel free to answer any or all): Anyone have some solid links to current/modern guides that would help me set this all up? No, the apache documentation site is not a guide ;-) Since I have a mix of static sites and PHP apps do I want/need both suexec and suphp installed? If so, does that introduce any challenges I should be aware of? Should I be looking at other options instead of suexec and suphp? I plan to give the end users SSH, SFTP or SCP access to their stuff (if that affects anything). Thanks in advance for your help.

  Read the article

• Apache mod_auth_kerb asking 2 authentication

  - by Rianto Wahyudi

  I've configured Apache to use mod_auth_kerberos. So far everything is working nicely for client thats connected to Active Directory and have their browser to ntlm enabled. When clients are not in the domain or the browser configurerd not to authenticate automatically, they are being prompted by 2 login prompt. The first login prompt is blank and the second one is the oen that we configured First Login prompt: http://www.screencast.com/t/ZGNlZTQwZm Second Login prompt : http://www.screencast.com/t/MDA2N2Fl From the log ( first authentication) : [Wed Jan 06 15:47:29 2010] [debug] src/mod_auth_kerb.c(1684): [client x.x.x.x] [pid 2562] kerb_authenticate_user entered with user (NULL) and auth_type Kerberos In the first loging prompt , I can put any text for username and password. Once the first login form submited, it will ask for the 2nd login prompt. Apache have following config : <Directory /web/apache2/htdocs> AllowOverride All AuthType Kerberos AuthName "Staff Access ONLY Kerb-Auth" KrbAuthRealms EXAMPLE.COM Krb5Keytab /etc/httpd/conf.d/example.ktab Allow from localhost Require valid-user <Directory> What could be the cause of the first authentication and how can I get rid of them ?

  Read the article

• Can you configure multiple KMS hosts in a primary / secondary relationship?

  - by Mark Hall

  We have two datacenters in our environment: primary and DR. I need to deploy a KMS service, and to be proactive, I would like to have a host in both datacenters. From what I have read, you can have up to 6 hosts without calling Microsoft, and it appears that what will happen is that a SRV record for each host will be placed in DNS. The client will query for those SRV records and randomly choose a host for the initial activation and will use that same server for all renewals. The server can be changed manually through a script and will automatically change if the initial server is unavailable when activating or renewing. My question is has anyone found a way to designate one server as the primary KMS host and designate the other as failover only? The reason I ask is that it is preferred that the client communicate with the primary datacenter during normal operations and only talk to the DR datacenter when needed because the bandwidth between the offices and the DR datacenter is limited compared to the primary. I am sure that this has been done before but I can not find it MSFT's documentation. Thanks, Mark

  Read the article

• samba4 dc "network location cannot be reached"

  - by mitchell babies peters

  to clear the air centos 6.4? (maybe 6.3) as the server, running samba 4.0.10, trying to add a windows 7 client that has connectivity to the server. this is what windows shouts as me as it mocks my dependence on network infrastructure. "the network location cannot be reached." i have access to the domain contoller (dc) im using the dc as the domain name server (dns) already, and the name is correctly resolving, and it is correctly forwarding outbound traffic. i have nothing but self taught experience with active directory(ad) so if i am missing something obvious, please shout it out, but keep the verbal abuse to a minimum. i checked samba4DC + my error and found nothing relevant to my issue, if i missed something please point me in that direction. the weekend is just starting as i write this so i probably wont be back on to check this post for a day or three, but i might because this mystery is killing me. i followed the samba4 as a dc guide here and i supplimented gaps with this i have tested kerberos, ntp, and set my DC as the clock to sync to in my windows client and it appears to be a very small fraction of a second off so that shouldn't be it. also, firewall and selinux are both off for testing. i have also tried disabling ipv6, and cleared the registry of ipv6 records (allegedly the default samba4 as a DC runs as windows server 2003 which allegedly does not support or tolerate the existence of ipv6, fair warning, i heard this on the internet so it is probably a lie) i have tried a few other things that i have forgotten because i have been doing this for a day and a half now. ideas welcome. suggestions for alternatives are also welcome, as long as they are free. i was given a budget of $0 dollars and told to implement active directory (no prior knowledge of active directory at that point).

  Read the article

• NATing IPv4 while routing IPv6

  - by Hugo

  I've the following setup: client(s) <---> (eth0) router (eth1) <---> wan I have a static IPv4 address and a /48 IPv6 address block. I need to connect all the clients to (wan). Each client will have it's own public IPv6. Meanwhile, I need to NAT those same clients over to (wan). Everything IPv4-related and the NAT are working fine. The IPv6 communication to/from (eth0)<-(clients) works fine, as does the IPv6 communication from (eth1)<-(wan) works fine. To provide IPv6 to all my clients, I've thought of too choices: Having the router as a gateway, which different IP on each interface. This sounds like I need to tell my ISP to route the entire block through that single IP, so it's not really an option. Transparently pass IPv6 packets to/from eth0<-eth1, so all clients can communicate with the upstream gateway (I would actually have a switch here if it weren't for the need to remain IPv4 compatible). So, since I've opted for the second choice, I'm in doubt: How can I pass all IPv6 traffic from eth0 to eth1 transparently? What I need is a level 3 bridge, but linux's bridgeutils create a level 2 bridge (which would bridge ipv4 as well, and I can't have that). This is a DD-WRT device, but it's pretty much an embeded linux, so most suggestions that would work on linux are welcome. Thanks.

  Read the article

• Apache 403 after configuring varnish

  - by w0rldart

  I just don't know where else to look and what else to do. I keep getting a 403 error on all my vhosts after setting varnish 3.0 Apacher log: [error] [client 127.0.0.1] client denied by server configuration: /etc/apache2/htdocs Headers: http://domain.com/ GET / HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:16.0) Gecko/20100101 Firefox/16.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Cookie: __utma=106762181.277908140.1348005089.1354040972.1354058508.6; __utmz=106762181.1348005089.1.1.utmcsr=OTHERDOMAIN.com|utmccn=(referral)|utmcmd=referral|utmcct=/galerias/cocinas Cache-Control: max-age=0 HTTP/1.1 403 Forbidden Vary: Accept-Encoding Content-Encoding: gzip Content-Type: text/html; charset=iso-8859-1 X-Cacheable: YES Content-Length: 223 Accept-Ranges: bytes Date: Sat, 01 Dec 2012 20:35:14 GMT X-Varnish: 1030961813 1030961811 Age: 26 Via: 1.1 varnish Connection: keep-alive X-Cache: HIT ---------------------------------------------------------- /etc/default/varnish: DAEMON_OPTS="-a ip.ip.ip.ip:80 \ -T localhost:6082 \ -f /etc/varnish/main.domain.vcl \ -S /etc/varnish/secret \ -s file,/var/lib/varnish/$INSTANCE/varnish_storage.bin,1G" #-s malloc,256m" My vcl file: http://pastebin.com/axJ57kD8 So, any ideas what I could be missing? Update Just so you know, ports: NameVirtualHost *:8000 Listen 8000 and <VirtualHost 205.13.12.12:8000>

  Read the article

• Microsoft Office 2003 applications crash on 'Save As' to a network mapped drive

  - by Archit Baweja

  Hey guys, so I'm not sure if it belongs on ServerFault forums so figured I'd ask here first because its a workstation/client side issue. I have a client where we have windows server 2003 setup, with windows xp professional setup on all the workstations. We've setup a 'domain' and all workstations logon to the domain (authenticated by the Windows Domain Controller), and in the logon script we map drives on to each workstation. Everything is working peachy except for one workstation, where when I open a file in excel from a mapped drive, it opens fine, but when I go to hit Save As, the Save As dialog pops and hangs up. I cannot perform any other action in excel. When I try cancel the Save As dialog, excel crashes. The mapped drive opens up fine in Windows Explorer. To further investigate this issue, I created a new blank text document on the network drive in Windows Explorer. I then opened it. Then hit save as, and the Save As dialog opened up fine and it would let me save the document. I repeated the above steps for a word document. However this time the Save As dialog hung/froze again. So I'd imagine its a Microsoft Office Issue. Any ideas?

  Read the article

• amavisd + postfix + dovecot blocks gif images

  - by David W

  I occasionally have a client who tries to email me and says his email gets blocked by my server. When I check the logs, I see this: Sep 6 18:12:52 myers amavis[15197]: (15197-08) p.path BANNED:1 [email protected]: "P=p003,L=1,M=multipart/mixed | P=p002,L=1/2,M=application/ms-tnef,T=tnef,N=winmail.dat | P=p004,L=1/2/1,T=image,T=gif,N=image001.gif,N=image001.gif", matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" And then a little later... Sep 6 18:12:58 myers amavis[15197]: (15197-08) Blocked BANNED (.image,.gif,image001.gif,image001.gif), [213.199.154.205] [157.56.236.229] <[email protected]> - > <[email protected]>, quarantine: banned-g4QhZGvwJvDF, Message-ID <6A9596BE385EC1499F83E464FA9ECCA20C668320@BY2PRD0611MB417.namprd06.prod.outlook.com>, mail_id: g4QhZGvwJvDF, Hits: -, size: 20916, 8439 ms From this and the bounce that he forwards me (to a different address I give him), I determine that its bouncing because of the file in his signature (image001.gif). However, that does NOT match the "key" in this part of the log: matching_key="(?-xism:^\\.(exe|lha|tnef|cab|dll)$)" Furthermore, the .gif extension is nowhere to be found in the /etc/amavisd.conf file (i.e. I'm not blocking emails because they contain .gif images). Am I missing something here? This is strange... and annoying.

  Read the article

• Referencing SQL Server 2008 R2 SMO from Visual Studio 2010

  - by user69508

  Hello. We read a number of things about referencing SQL Server SMO from Visual Studio but still don't have the definite answers we need. So, here it goes... A number of years ago we created a C# application using Visual Studio 2005 and SQL Server 2005. In that application, we added .NET references to a number of SQL Server SMO objects, and everything worked fine. Those references were: Microsoft.SqlServer.ConnectionInfo GAC 9.0.242.0 Microsoft.SqlServer.Smo GAC 9.0.242.0 Microsoft.SqlServer.SqlEnum GAC 9.0.242.0 We have now migrated to Visual Studio 2010 and SQL Server 2008 R2. However, when we try to reference those same SMO objects for SQL Server 2008 R2, they don't appear in the .NET references tab. We're wanting to reference the SQL Server 2008 R2 version of those same SMO assemblies for our upgraded C# application. On our development machines, we have SQL Server 2008 R2 Developer installed with all options, including the SDK such that the assemblies are found in C:\Program Files (x86)\Microsoft SQL Server\100\SDK\Assemblies. So, my first questions are: Are we supposed to do file references to the SMO assemblies instead of .NET references in Visual Studio 2010 w/ SQL Server 2008 R2? Or, is there some problem with our development machines such that the SMO assemblies are not appearing in the .NET references tab? Next, our production machines will have SQL Server 2008 R2 Workgroup installed with the client tools option selected, thus providing those same SMO assemblies in C:\Program Files (x86)\Microsoft SQL Server\100\SDK\Assemblies. So, the next questions are: When we release to production, are we supposed to redistribute the SMO assemblies with our application? Or, will our application work on the production servers without redistributing the SMO assemblies (since the client tools/SMO assemblies have been installed)? What else????? Thanks for the help!

  Read the article

• How to verify a self-signed certificate from another server using openssl?

  - by ntsue

  I am new to openssl and I am having some trouble verifying (from a client machine) an ftp server using ssl with a self-signed certificate. I generated the .cer file by going to my server in IIS and exporting the certificate without the private key. I believe that this is all that I should need on the client side, right? I use the following code to verify the certificate openssl verify ftp.cer and the error that I get back is error 20 at 0 depth lookup:unable to get local issuer certificate I tried this as well: openssl verify -CAfile ftp.cer ftp.cer but received the same error. From what I understand about SSL, this is happening because I have no chain of trust that connects to this server. By default, openssl did not install any trusted CAs and this is fine. I would just like to tell it to trust this server. I tried various tutorials telling me how to add a certificate authority, including this one here, however the instructions are for linux and include adding a symlink and I am trying to do this in windows. If anyone could provide any guidance on how to do this, or enlighten me if I am not understanding something correctly, I would greatly appreciate it. Thanks!

  Read the article

• RHEL 5.3 Kickstart - How specify location of individual package in Workstation folder?

  - by Ed

  I keep getting "package does not exist" errors during the install. I made a kickstart ISO to create an unattended install of a RHEL 5.3 build machine for C++ software releases. It pulls the kickstart config file from our internal web server. This is handy; it makes it easy to test and modify without having to make a new ISO. And I plan to check it in to version control if I can get it working. Anyway, the rpm packages are located in two folders on the disk; Client and Workstation. The packages install fine for the ones that are physically located under the Client folder. It cannot find those under the Workstation folder such as as doxygen and subversion complaining that packages do not exist. Is there a way to specify the individual package location? # ----------------------------------------------------------------------------- # P A C K A G E S # ----------------------------------------------------------------------------- %packages @gnome-desktop @core @base @base-x @printing @development-tools emacs kexec-tools fipscheck xorg-x11-server-Xnest xorg-x11-server-Xvfb #Packages Located in Workstation Folder *** Install can not find any of these ?? bison doxygen gcc-c++ subversion zlib-devel freetype-devel libxml2-devel Thanks in advance, -Ed

  Read the article

• VMware Virtual Infrastructure Web Access not starting on Fedora 14

  - by FusionHammer

  I am running a Fedora 14 server with VMware Server 2. When I initially installed VMware Server, everything was working fine. This included accessing Web Access on port 8333 (https) and 8222 (http). I had to perform a server restart and afterwards, the Web Access is not starting when I run: /etc/init.d/vmware-mgmt start The VMware Server Host Agent starts [OK], but the Web Access has no [OK] or [Failed] next to it. I also checked ports 8333 and 8222 by running a netstat, but neither are showing up. In addition, I checked the proxy.log and client.log files in the following directory: /usr/lib/vmware/webAccess/tomcat/apache-tomcat-6.0.16/logs/ The proxy.log doesn't have entries in it past 9-18-2012, which is the date the server restart occurred. The client.log is empty. I not sure what is causing this issue or what log files will be helpful in narrowing down the cause. I could re-install VMware Server, but I would like to narrow down the cause as it could occur again with the new re-installed environment.

  Read the article

• DNS Resolution doesn't work after uninstalling Cisco VPN & Deterministic Network Enhancer in Win 7

  - by Craig M

  I just upgraded my home PC to Windows 7 Ultimate 32 bit. After trying various methods to get the Cisco VPN client to work, I gave up and decided to just run it in XP mode. The last steps I tried were in this article ( http://social.technet.microsoft.com/Forums/en-US/w7itproappcompat/thread/d880dfe5-7f44-4955-8620-2a9355d8ea8b/ ) After that, I uninstalled the Cisco client and rebooted. I uninstalled the Deterministic Network Enhancer and rebooted again. Both uninstalled successfully, but now I'm not able to resolve any DNS. The only way I can resolve DNS is to reinstall the DNE, reboot, and uninstall the DNE. Then I am able to resolve DNS lookups until I reboot again. Once it's rebooted, no more DNS. Any ideas? Edit: I completely forgot I'd asked this question until harrymc posted his answer. I've since found out that to fix this problem, I need to disable my Local Area Connection and re-enable it. Once I do that I have no trouble making network connections until the next time I reboot at which point I repeat the process. It's annoying, but manageable since I reboot very infrequently.

  Read the article

• Unable to logon to vpn

  - by nitin pande

  My openvpn client log file- The interesting bit: Tue Oct 26 12:32:49 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:49 2010 TCP/UDP: Closing socket The rest of the log just in case: Tue Oct 26 12:32:35 2010 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Tue Oct 26 12:32:48 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:48 2010 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Oct 26 12:32:48 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 12:32:48 2010 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 12:32:48 2010 LZO compression initialized Tue Oct 26 12:32:48 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:48 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:48 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:48 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:48 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:32:48 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:32:48 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:32:48 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 TLS: Initial packet from 67.228.223.12:3389, sid=bd5f79fe 8475497f Tue Oct 26 12:32:49 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:49 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:49 2010 TCP/UDP: Closing socket Tue Oct 26 12:32:49 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:32:49 2010 Restart pause, 5 second(s) Tue Oct 26 12:32:54 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:54 2010 Re-using SSL/TLS context Tue Oct 26 12:32:54 2010 LZO compression initialized Tue Oct 26 12:32:54 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:54 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:54 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:54 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:54 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:32:54 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 TLS: Initial packet from 67.228.223.12:3389, sid=1643b931 ce240d5f Tue Oct 26 12:32:54 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:32:54 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:32:54 2010 TCP/UDP: Closing socket Tue Oct 26 12:32:54 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:32:54 2010 Restart pause, 5 second(s) Tue Oct 26 12:32:59 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:32:59 2010 Re-using SSL/TLS context Tue Oct 26 12:32:59 2010 LZO compression initialized Tue Oct 26 12:32:59 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:32:59 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:32:59 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:32:59 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:32:59 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:00 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 TLS: Initial packet from 67.228.223.12:3389, sid=cd439fb2 d625ca0d Tue Oct 26 12:33:00 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:00 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:00 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:00 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:00 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:05 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:05 2010 Re-using SSL/TLS context Tue Oct 26 12:33:05 2010 LZO compression initialized Tue Oct 26 12:33:05 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:05 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:05 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:05 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:05 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:06 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 TLS: Initial packet from 67.228.223.12:3389, sid=28f0cb87 69c90cde Tue Oct 26 12:33:06 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:06 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:06 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:06 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:06 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:11 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:11 2010 Re-using SSL/TLS context Tue Oct 26 12:33:11 2010 LZO compression initialized Tue Oct 26 12:33:11 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:11 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:11 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:11 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:11 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:11 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 12:33:11 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 12:33:11 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 12:33:12 2010 TLS: Initial packet from 67.228.223.12:3389, sid=128becf9 f62adf0c Tue Oct 26 12:33:12 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 12:33:12 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 12:33:12 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:12 2010 SIGUSR1[soft,tls-error] received, process restarting Tue Oct 26 12:33:12 2010 Restart pause, 5 second(s) Tue Oct 26 12:33:17 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 12:33:17 2010 Re-using SSL/TLS context Tue Oct 26 12:33:17 2010 LZO compression initialized Tue Oct 26 12:33:17 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 12:33:17 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 12:33:17 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 12:33:17 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 12:33:17 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 12:33:20 2010 TCP/UDP: Closing socket Tue Oct 26 12:33:20 2010 SIGTERM[hard,init_instance] received, process exiting Guys I am extremely sorry for not presenting my error Log properly, please forgive me and give me your valuable advice. I am using windows 7 and I am using openvpn mainly to bypass censorship at UAE. I am using only client config file. Ca.crt file is in config folder Thanks and regards Nitin My error Log with Config1 file Tue Oct 26 21:24:34 2010 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Tue Oct 26 21:24:46 2010 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue Oct 26 21:24:46 2010 Control Channel Authentication: using 'ta.key' as a OpenVPN static key file Tue Oct 26 21:24:46 2010 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 21:24:46 2010 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Tue Oct 26 21:24:46 2010 LZO compression initialized Tue Oct 26 21:24:46 2010 Control Channel MTU parms [ L:1544 D:168 EF:68 EB:0 ET:0 EL:0 ] Tue Oct 26 21:24:46 2010 Data Channel MTU parms [ L:1544 D:1450 EF:44 EB:135 ET:0 EL:0 AF:3/1 ] Tue Oct 26 21:24:46 2010 Local Options hash (VER=V4): 'ee93268d' Tue Oct 26 21:24:46 2010 Expected Remote Options hash (VER=V4): 'bd577cd1' Tue Oct 26 21:24:46 2010 Attempting to establish TCP connection with 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TCP connection established with 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TCPv4_CLIENT link local: [undef] Tue Oct 26 21:24:47 2010 TCPv4_CLIENT link remote: 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 TLS: Initial packet from 67.228.223.12:3389, sid=4244e662 e5a0572a Tue Oct 26 21:24:47 2010 TLS Error: cannot locate HMAC in incoming packet from 67.228.223.12:3389 Tue Oct 26 21:24:47 2010 Fatal TLS error (check_tls_errors_co), restarting Tue Oct 26 21:24:47 2010 TCP/UDP: Closing socket Tue Oct 26 21:24:47 2010 SIGUSR1[soft,tls-error] received, process restarting client config file: client dev tun proto tcp remote openvpn1.flashvpn.com 3389 float resolv-retry infinite nobind persist-key persist-tun ca ca.crt ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 auth-user-pass route-method exe route-delay 2

  Read the article

< Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >