Search Results

Search found 20049 results on 802 pages for 'virtual drive'.

Page 423/802 | < Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• External USB HD with -optional- mains?

  - by Stephen

  Hi, I'm Christmas-present-buying, and I'd appreciate recommendations for a USB HD with an optional mains power input. I've hunted, but can't find all the information I want (partially due to sketchy product specifications). Background: This is for a digital TV which I do not own, and so I'd like to get it correct first time. The TV has a USB port to allow recording straight to disk, but the manuals don't say how much power can be drawn through the USB port. The manual's instructions state, possibly generically, to plug the drive in before connecting to the TV. Ideally I'd like a small (2.5"?) drive which can draw power over USB, with an mains power input if it turns out the USB port on the TV doesn't offer enough juice. The ideal is to use one cable, two max. A powered USB hub would introduce too much clutter. I've spotted that the LaCie Petit drives have what appears to be an additional power input, but I'm not even sure from the specs what that is. And the device doesn't ship with a mains adapter. Suggestions?

  Read the article

• DriveImage XML fails with a Windows Volume Shadow Service Error

  - by ssvarc

  I'm trying to image a SATA laptop hard drive, using DriveImageXML, that is attached to my computer via a USB adapter. I'm running Win7 Ultimate 64 bit. DriveXML is returning: Could not initialize Windows Volume Shadow Service (VSS). ERROR C:\Program Files (x86)\Runtime Software\Drivelmage XML\vss64.exe failed to start. ERROR TIMEOUT Make sure VSSVC.EXE is running in your task manager. Click Help for more information. VSSVC.EXE is running in Task Manager, as is VSS64.exe. Looking at the FAQ on the Runtime webpage this turned up: Please verify in Settings-Control Panel-Administrative Tools-Services that the following services are enabled: MS Software Shadow Copy Provider Volume Shadow Copy Also make sure you are able to stop and start these services. Possible reasons for VSS failures: For VSS to work, at least one volume in your computer must be NTFS. If you use only FAT drives, VSS will not function. The required NTFS volume does not need to be identical with the volume you want to image. You should make sure that VSSVC.EXE is running in your task manager. If the problems persist, registering "oleaut.dll" and "oleaut32.dll" using "regsvr32" might help. Both of those services are running and can be started and stopped without issue. Using "regsvr32" to register ""oleaut32.dll" returns successful, but "oleaut.dll" returns: The module "oleaut.dll" failed to load. Make sure the binary is stored at the specified path or debug it to check for problems with the binary or dependent .DLL files. The specified module could not be found. Some other information that might be relevant. Browsing to the drive is successful, but accessing certain folders returns an "access" error. Windows runs a permissions adder that adds the current user profile to the NFTS permissions. Could this be the cause of the issue? DriveImage XML is running as Administrator. Thoughts?

  Read the article

• Asus MyCinema U3100mini Choppy

  - by dsimcha

  I'm running an Asus MyCinema U3100mini ATSC on Windows 7 64-bit. When I play live TV in Windows Media Center, it's very choppy and uses 500+ MB of RAM, I'm guessing due to the hard drive buffering functionality. Is there any way to disable the live TV pause buffer completely? If not, can anyone recommend alternative software that: Works with the MyCinema. Is lightweight and not horribly bloated with features I'll never use like Windows Media Center is. Edits: This is a dual boot system. I've discovered that the tuner actually works fine on XP. It also works fine on my other computer, which has slower hardware and also runs Windows 7 64-bit. The problem actually seems to be with playback at large screen sizes, not with hard drive buffering. Everything works fine below a certain window size and fails for large windows or full screens. Also, the same thing seems to happen whether playing live or recorded TV. As far as the obvious stuff goes, I have the latest video drivers from ATI for my Radeon x1050.

  Read the article

• tap interfaces always disabled in linux bridge

  - by Dani Camps

  I have a physical interface eth0, and I want to create two virtual interfaces and bridge them with eth0. For this purpose I do: #Create the virtual interfaces tunctl -t tap0 tunctl -t tap1 ifconfig tap0 up ifconfig tap1 up #Create the bridge brctl addbr br0 brctl stp br0 off brctl addif br0 eth0 brctl addif br0 tap0 brctl addif br0 tap1 #Turning up the bridge ifconfig br0 up However my problem if that the tap interfaces always appear disabled in the bridge, and no traffic flows to them. $brctl show br0 bridge name bridge id STP enabled interfaces br0 8000.080027cabeba no eth2 tap0 tap1 $brctl showstp br0 br0 bridge id 8000.080027cabeba designated root 8000.080027cabeba root port 0 path cost 0 max age 20.00 bridge max age 20.00 hello time 2.00 bridge hello time 2.00 forward delay 15.00 bridge forward delay 15.00 ageing time 300.01 hello timer 0.00 tcn timer 0.00 topology change timer 0.00 gc timer 298.42 flags eth2 (1) port id 8001 state forwarding designated root 8000.080027cabeba path cost 4 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8001 forward delay timer 12.97 designated cost 0 hold timer 1.24 flags tap0 (2) port id 8002 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags tap1 (3) port id 8003 state disabled designated root 8000.080027cabeba path cost 100 designated bridge 8000.080027cabeba message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags Is there any way to set the tap interfaces in forwarding state? I do not understand why they are not because STP is disabled. Cheers Daniel

  Read the article

• 403 Forbidden error on Mac OSX - Apache and nginx

  - by tlianza

  Hi All, There are a million questions like this on Google, but I haven't found a solution to my problem. The default Apache install on my Mac is giving 403 Forbidden errors for everything (default directory, user home directory, virtual server, etc). After sifting through the config files, I figured I'd give nginx a try. Nginx serves files fine from it's home directory, but it won't serve files from a subfolder of my user directory. I've configured a simple virtual host, and requesting index.html returns a 403-forbidden. The error message in nginx's log file is pretty clear - it can't read the file: 2011/01/04 16:13:54 [error] 96440#0: *11 open() "/Users/me/Documents/workspace/mobile/index.html" failed (13: Permission denied), client: 127.0.0.1, server: local.test.com, request: "GET /index.html HTTP/1.1", host: "local.test.com" I've opened up this directory to everyone: drwxrwxrwx 6 me admin 204B Dec 31 20:49 mobile And all the files in it: $ ls -lah mobile/ total 24 drwxrwxrwx 6 me admin 204B Dec 31 20:49 . drwxr-xr-x 71 me me 2.4K Dec 31 20:41 .. -rw-r--r--@ 1 me me 6.0K Jan 2 18:58 .DS_Store -rwxrwxrwx 1 me admin 2.1K Jan 4 14:22 index.html drwxrwxrwx 5 me admin 170B Dec 31 20:45 nbproject drwxrwxrwx 5 me admin 170B Jan 2 18:58 script And yet, I cannot figure out why the nginx process cannot read index.html. It's running as the "nobody" user, but the permissions are set such that anyone can read them.

  Read the article

• How to diagnose website performance/app pool recycling with Windows 2008/IIS7

  - by ilasno

  Ok, so there are various symptoms here (clients and and our own employees complaining of intermittent slowdowns, getting 'kicked out' to login page or just having a save request not properly save the submitted data). The environment: Windows Server 2008 (Datacenter), Service Pack 2, 64-bit, 2x2.8 GHz processors, 7.5 GB RAM MS SQL Server 2008 (running on the same machine) IIS 7 There are ~10 websites running on the server, each in their own application pool - most of these pools are running in Integrated mode, 2 are in Classic, all are on .NET 2.0 and all run as ApplicationPoolIdentity. I'm trying to analyze, diagnose, and troubleshoot and am struggling with where to get more info about what could be happening. Here are some steps i have already taken: Set each application pool to recycle once per day, and removed any other automatic recycling Set a Virtual Memory Limit for each to 1024000KB (1GB) Enabled ALL 'Generate Recycle Event Log Entry' entries (Config Changes, Isapi Reported Unhealthy, Manual Recycle, Private Memory Limit Exceeded, Regular Time Interval, Request Limit Exceeded, Specific Time, Virtual Memory Limit Exceeded) I have seen the app pool processes recycle (in Task Manager) - a new one will start up, and then the first one dies off - and this has happened without the memory or time going over the settings. This is a fairly new server, and most of these came from Windows Server 2003/IIS6. Any 'next steps' for setting up information gathering, logging, diagnosing, etc. would be much appreciated! j

  Read the article

• Error when starting .Net-Application from ThinApp-Application

  - by user50209

  one of our customers uses SAP through VMWare ThinApp. In SAP there is a button that launches an .Net application from a server. When starting the .Net-application directly, there is no error. If the user tries to start the application by clicking the button in the ThinApp-Application, it displays the following errors: Microsoft Visual C++ Runtime Library R6034 An application has made an attempt to load the C runtime library incorrectly. Please contact the application's support team for more information. After clicking "OK" it displays: Microsoft Visual C++ Runtime Library Runtime Error! R6030 - CRT not initialized So, does the customer have to install some components into his ThinApp (if yes, which?) to get things working? Regards, inno ----- [EDIT] ----- @Sean: It's installed the following way: The .exe of the .Net-Application is on a mapped drive on a server. All clients have the requirements installed (.Net-framework for example) and start the .exe from the mapped drive. The ThinApp-Application tries to start this application and throws the mentioned exceptions. AFAIK there are no entry points for this application configured. What I should also mention is: The .Net-Application crashes during execution. That means, we have a debug mode implemented that shows what the application is doing. The application shows what it's doing and after some steps it crashes. The interesting point is: It's a .Net-application, not a C++ Application.

  Read the article

• Do you known a reputable backup software that can capture ONLY file system structure + attributes, WITHOUT file content

  - by bogdan

  Is there, on Windows, a reputable backup software out there capable of capturing ONLY a file system's directory and file structure, along with each item's attributes, WITHOUT capturing the actual file content (all files should be zero-length in the backup). I thoroughly searched the web for a solution and wasn't able to find one. Scenario when this would be very useful: I have a large drive with a huge amount of files. If the drive dies, I don't care so much about the content in these files (I can always download this content again from the Internet at any time) but I do care HUGELY about the names of the files that were on it, possibly also about their MD5 hashes and other classic file attributes (especially created-date / modified-date). The functionality I need is present to an extent in "media"/file cataloging software (i.e. whereisit) and, to a lesser extent, in a Total Commander set of extensions (DiskDir, DiskDirExtended). The huge drawback with cataloging software is that it's not designed to store previous versions of each item (AFAIK) and, most importantly, it has very weak content backup capabilities. I managed to think of a hack but I hope there's some backup software out there that already has this capability and I just failed to find it, thus this question. The hack: RoboCopy could be used with /CREATE (CREATE directory tree and zero-length files only) or /COPY (what to COPY for files) without the D=Data flag, to clone a directory structure into one where all files are zero-length but have the desired attributes. Then I would backup the cloned directory structure with a reputable backup software. I would really love to avoid a hack like this one, if possible. Thanks, Bogdan

  Read the article

• Sending emails with Thunderbird + Postfix + Zarafa does not work

  - by Sven Jung

  I installed zarafa on my vserver and use as MTA postfix. The webaccess works fine, I can revceive and send emails, also receiving mails with thunderbird (IMAP ssl/tls) works. But there is a problem, sending emails with thunderbird. I established an account in thunderbird with imap ssl/tls connection which works finde, and a starttls smtp connection on port 25 for the outgoing mail server. If I try to send an email with thunderbird I get an error: 5.7.1 Relay access denied this is my mail.log Sep 7 16:10:07 postfix/smtpd[6153]: connect from p4FE06C0A.dip.t-dialin.net[79.224.110.10] Sep 7 16:10:08 postfix/smtpd[6153]: NOQUEUE: reject: RCPT from p4FE06C0A.dip.t-dialin.net[79.224.110.10]: 554 5.7.1 <[email protected]>: Relay access denie$ Sep 7 16:10:10 postfix/smtpd[6153]: disconnect from p4FE06C0A.dip.t-dialin.net[79.224.110.10] and this my /etc/postfix/main.conf # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache virtual_mailbox_domains = firstdomain.de, seconddomain.de virtual_mailbox_maps = hash:/etc/postfix/virtual virtual_alias_maps = hash:/etc/postfix/virtual virtual_transport = lmtp:127.0.0.1:2003 myhostname = mail.firstdomain.de alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all inet_protocols = ipv4 I don't know what to do, because actually sending mails to internal and external addresses works with the webaccess. Perhaps somebody can help me?

  Read the article

• Laptop hangs on POST and does not finish except on rare occasions

  - by user1049697

  I have an old Toshiba Satellite A100 laptop that hangs on POST when I try to start it. On rare occasions it does finish the POST and boots Windows successfully, but most times it just finishes it partially and continues to hang. I can enter the BIOS though when it has frozen, but I have to open the DVD-drive first for some reason. The keyboard is not quite right either, and I can't navigate the BIOS properly because the arrow keys doesn't work. I tried an external keyboard, but the problem persisted. I have tried to remove the memory, hard drive, and battery to see if any of these were the problem, but it did not solve it. The one logical thing left to do would be to remove the CMOS battery, but the "brilliant" engineers at Toshiba have place it such that a complete disassembly of the machine is necessary. What this all boils down to is basically the question of whether I can "save" this machine and get it to boot properly, or if I should just send it off to recycling. I suspect it might need costly repairs, but I can't bring myself to throw it away before I have made sure it's completely dead.

  Read the article

• Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

  - by Brady

  I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

  Read the article

• Creating Active Directory on an EC2 box

  - by Chiggins

  So I have Active Directory set up on a Windows Server 2008 Amazon EC2 server. Its set up correctly I think, I never got any errors with it. Just to test that I got it all set up correctly, I have a Windows 7 Professional virtual machine set up on my network to join to AD. I set the VM to use the Active Directory box as its DNS server. I type in my domain to join it, but I get the following error: DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "ad.win.chigs.me": The query was for the SRV record for _ldap._tcp.dc._msdcs.ad.win.chigs.me The following domain controllers were identified by the query: ip-0af92ac4.ad.win.chigs.me However no domain controllers could be contacted. Common causes of this error include: - Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses. - Domain controllers registered in DNS are not connected to the network or are not running. It seems that I can talk to Active Directory, but when I'm trying to contact the Domain Controller, its giving a private IP to connect to, at least thats what I can make out of it. Here are some nslookup results. > win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Non-authoritative answer: Name: ec2-184-73-35-150.compute-1.amazonaws.com Address: 10.249.42.196 Aliases: win.chigs.me > ad.win.chigs.me Server: ec2-184-73-35-150.compute-1.amazonaws.com Address: 184.73.35.150 Name: ad.win.chigs.me Address: 10.249.42.196 win.chigs.me and ad.win.chigs.me are CNAME's pointing to my EC2 box. Any idea what I need to do so that I can join my virtual machine to the EC2 Active Directory set up I have? Thanks!

  Read the article

• Dell 2970 - HP 1/8 G2 autoloader keeps falling off LSI 2032 SCSI chain

  - by middaparka

  I've a somewhat irritating problem with a Dell 2970 that has a HP 1/8 G2 autoloader (the Ultrium LTO 2 model) attached to the Dell/LSI 2032 non-RAID SCSI card. In essence, sometimes the autoloader/drive completely fails to appear on the SCSI chain (i.e.: there's neither a media changer or tape drive present within the device manager) and sometimes it appears but then subsequently disappears at a seemingly random (yet always inconvenient) time, resulting in backup failures. On most occasions, there are simply no errors logged in the system event log, but I did manage to capture a series of LSI_SCSI event ID 11 ("The driver detected a controller error on \Device\RaidPort0") errors followed by an event ID 129, ("Reset to device, \Device\RaidPort0, was issued") error during testing. I've tried two different cables, both with the same effect – sometimes the autoloader appears (for a while), sometimes it's completely absent. There's only one terminator I've tried to use, but as I've since successfully tested the autoloader on multiple occasions (albeit via a Adaptec U160 card on a different machine), my gut feel is that the issue doesn't lie with the terminator, or indeed the autoloader itself. As such, I'm just wondering if anyone has any ideas? It's most likely not relevant, but this is all under Windows SBS 2008, running Backup Exec 12.5 SBS edition (the Dell version), both fully patched. Addidtionally, the autoloader is running the latest firmware. It's been a while since I've dealt with anything SCSI, so all suggestions will be gratefully, gratefully received.

  Read the article

• How to change my W2k8 System Partition?

  - by Chris May

  On my Windows 2008 server, my C: is 1.5 TB, and the partition is marked as: Healthy (Boot, Page File, Active, Crash Dump, Primary Partition) and somehow I ended up with a 2GB D: that is marked as Healthy (System). On this D: drive are only a few MB worth of files (bootmgr, boot folder, bootsect.bak), but all Windows files are on the c:. I've done everything I can to remove the (System) mark. I tried using bcdedit, I tried marking the C:partition as "Active", I tried using bootsect.exe to assign the C: drive as the boot partition. Maybe I didn't do one of those steps correct, but I've tried everything I can. When I got my new Dell Poweredge T710, I didn't bother removing their 2 small drives before I put in my 2 new large drives. So I think when I installed W2k8 Server, maybe dell left some bootable partition on their drives to help me install the OS, but I never used it and just booted right from the install CD. Can anyone help me remove the (System) mark from the D: so I can remove the D: partition and still boot to the C:? I know I could remove the D: drives and reinstall windows, but I'm trying to avoid a total reinstall.

  Read the article

• Installing Windows 7 from USB on a Thinkpad T61

  - by Halik

  I am trying to install Windows 7 Professional from USB 3.0 flashdrive, on a Thinkpad T61. The problem is, Thinkpads BIOS will not detect the flash drive as bootable medium, and won't allow to boot from it. What I did: Enabled USB BIOS Support in BIOS (it was on by default) In startup menu, added USB HDD to boot order (it has '-' sign in front of it) Created Windows 7 install media with UNetbootin, WinUSB (linux tool) dd and Grub4DOS. As you can tell, currently, I only have access to Linux machine to make the flashdrive. What happens: The T61 BIOS shows '-USB HDD' in boot order menu. The '-' sign suggests that the plugged flash drive is currently not bootable. The same flashdrive (with the same Windows image on it) is booting without any problems on a Dell D430 and Lenovo Y550. Also, Ubuntu 12.04 install USB created with Unetbootin shows as bootable ('+' sign in BIOS boot order menu) and boots from the F12 boot menu. Additional info thinkwiki.org says that some Thinkpad BIOSes do not use MBR on flashdrives. It suggests using Extended-IPL boot loader, but the provided links are broken and there seems to be no mirrors. Solution: http://superuser.com/a/430186/54970

  Read the article

• Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

  - by cpm

  I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

  Read the article

• Damaged partition after disk image

  - by Charles Gargent

  I am trying to clone/backup a disk with Windows 7 Pro 64bit on it. First I tried Easus Todo Backup and used disk clone option without sector by sector copy. I then plugged in the new drive and I get the following error. "Invalid or damaged Bootable partition" I then plugged the old drive back in and I am greeted with the same error. My next step was to try the sector by sector disk clone, but still I get the same error. I have tried fixing the mbr with the windows disk but that makes no difference. I have tried some other free tools and I get the same error. I have tried this on a different machine running Windows 7 Enterprise 32bit without this problem. I have done some searching and the only thing I can come up with is this post from the Acronis forums http://forum.acronis.com/forum/8254 suggesting that the bios is reading my disk geometry incorrectly. Can anyone shed any light on this, is there a way I can fix this either in the bios or repair the mbr every time I reimage it?

  Read the article

• Mac OS X Disk Encryption - Automation

  - by jfm429

  I want to setup a Mac Mini server with an external drive that is encrypted. In Finder, I can use the full-disk encryption option. However, for multiple users, this could become tricky. What I want to do is encrypt the external volume, then set things up so that when the machine boots, the disk is unlocked so that all users can access it. Of course permissions need to be maintained, but that goes without saying. What I'm thinking of doing is setting up a root-level launchd script that runs once on boot and unlocks the disk. The encryption keys would probably be stored in root's keychain. So here's my list of concerns: If I store the encryption keys in the system keychain, then the file in /private/var/db/SystemKey could be used to unlock the keychain if an attacker ever gained physical access to the server. this is bad. If I store the encryption keys in my user keychain, I have to manually run the command with my password. This is undesirable. If I run a launchd script with my user credentials, it will run under my user account but won't have access to the keychain, defeating the purpose. If root has a keychain (does it?) then how would it be decrypted? Would it remain locked until the password was entered (like the user keychain) or would it have the same problem as the system keychain, with keys stored on the drive and accessible with physical access? Assuming all of the above works, I've found diskutil coreStorage unlockVolume which seems to be the appropriate command, but the details of where to store the encryption key is the biggest problem. If the system keychain is not secure enough, and user keychains require a password, what's the best option?

  Read the article

• Virus ridden computer freezes on startup - can't access safe mode

  - by Eric

  Someone whom I love but who cannot be trusted with a live internet connection downloaded a particularly nasty virus that in turn downloaded a variety of unknown other viruses onto my home computer. The computer now freezes completely a few seconds after reaching the desktop and is unresponsive to any keyboard or mouse command. There are videos of my little kid on this hard drive that are not backed up and that I cannot bear to lose. But if I could get in there long enough to copy them off to an external drive I would have no problem doing a clean windows install to fix the problem; everything else is backed up online but the videos were too large. Normally I would start by going into safe mode but I have a large Dell monitor that doesn't show anything until the welcome screen appears. I think that I have gotten into the setup screen once or twice by mashing keys before I can see anything, but this monitor doesn't support that so I can't see what I'm doing to get it to boot from CD or anything else. I'm at my wits end. Any advice?

  Read the article

• My Computer hangs for a few minutes just after startup, and then is fine.

  - by EvilChookie

  So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

  Read the article

• Find out when a system went down?

  - by Clinton Blackmore

  I have a Mac OS X 10.5 server, with a RAID set in it, that went down due to a power outage on Thursday, and the machine is not happily booting right now*. It is possible to find out when the machine went down, while not booted off the internal drive? (I'm booted off an external drive, waiting for the RAID sets to initialize.) Normally, I'd run last. The man page doesn't indicate that I can run it against a different startup volume. It looks possible to parse /var/log/utmpx, but I don't think it'd be worthwhile to try to do that from scratch for this one-off problem. * I'm still trying to figure out why it isn't happy, and may ask a follow-up question. Right now I can see that UserNotificationCenter crashed repeatedly early Thursday morning, and that securityd, mdworker, and ARDAgent crash shortly after startup [I think -- I want to verify when the box went up and down]. The login window does not come up right (I think it is crashing or not able to cope with a dead securityd). The box is supposed to be set to go down when the UPS tells it power is out; at the moment, I'm wondering if it went down, and turned back on multiple times! I sure hope not.

  Read the article

• SSD causing 100% CPU usage in Apache/PHP

  - by Tim Reynolds

  I wanted to increase the performance on my development laptop so I added an Intel 320 Series SSD as my primary drive. Everything is amazingly fast, as expected, except Apache/PHP. I develop Magento by using an Ubuntu 10.10 virtual machine. Information: Host OS: Win 7 Professional 64bit Guest OS: Ubuntu 10.10 32bit Processor: i7 Chipset QM55 SSD: Intel 320 Series 160gb 30% full HDD: Hitachi 320gb 50% full (in side bay using an adapter) Laptop: Lenovo T510 Using: Shared folders Apache Version: 2.2.16 PHP Version: 5.3.3-1 APC Version: 3.1.3p1 APC Memory: 128M Using tmpfs for cache, log, session directories in Magento In the VM running on the SSD (VM files and source files are on the same drive) loading a product page in the Admin takes on average 26.2 seconds and uses 100% CPU for nearly the entire time. In the VM running on the old HDD loading the same page takes on average 4.4 seconds. It mostly uses around 40-50% of the CPU while rendering the page. I have read this post: Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)? It says to change some settings in the bios. I have turned any and all power management features off in the bios. I can't for the life of me understand why this would be happening.

  Read the article

• Prevent master to fall back to master after failure

  - by Chrille

  I'm using keepalived to setup a virtual ip that points to a master server. When a failover happens it should point the virtual ip to the backup, and the IP should stay there until I manually enable (fix) the master. The reason this is important is that I'm running mysql replication on the servers and writes should only be on the master. When I failover I promote the slave to master. The master server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP1 } vrrp_instance APP1 { interface eth0 state EQUAL virtual_router_id 61 priority 999 nopreempt virtual_ipaddress { 217.x.x.129 } smtp_alert } Backup server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP2 } vrrp_instance APP2 { interface eth0 state EQUAL virtual_router_id 61 priority 100 virtual_ipaddress { 217.xx.xx.129 } notify_master "/etc/keepalived/notify.sh del app2" notify_backup "/etc/keepalived/notify.sh add app2" notify_fault "/etc/keepalived/notify.sh add app2” smtp_alert }

  Read the article

< Previous Page | 419 420 421 422 423 424 425 426 427 428 429 430  | Next Page >