Search Results

Search found 27336 results on 1094 pages for 'network state'.

Page 426/1094 | < Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >

• Simple Workstation Imaging Solution?

  - by Will

  Hey guys, I need a fairly cheap imaging solution for Windows XP corporate desktops. Ideally, I'd be able to set up a desktop exactly as we want it, create an image, deploy this image to a server, then boot a new desktop to a CD/USB Drive/Network and quickly set up the workstation. Ideally, each computer would also have a unique workstation name. Any ideas? Right now I'm using a custom built Linux DD solution, but it's slow, not network-based, can't image multiple computers at the same time as there's only one copy on a USB drive, and can't uniquely name the computers. Thanks, Will

  Read the article

• Proxmox 31 + KVM routing + IP subnet + csf

  - by KeyJey

  We have proxmox 3.1 server in netzner with routuing network and IP subnet block. We want to implement csf firewall without interfering the traffic of the KVM VMs, what would be the easiest way? We readed that we should add this lines to /etc/csf/csfpost.sh: iptables -A FORWARD -d 144.76.223.155 -j ACCEPT iptables -A FORWARD -d 144.76.223.156 -j ACCEPT iptables -A FORWARD -d 144.76.223.157 -j ACCEPT iptables -A FORWARD -d 144.76.223.158 -j ACCEPT iptables -A FORWARD -d 144.76.223.159 -j ACCEPT iptables -A FORWARD -d 144.99.183.323 -j ACCEPT But when we enable csf the ping breaks, this is the network config (IPs are modified): auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 144.76.166.100 netmask 255.255.255.255 pointopoint 144.76.183.97 gateway 144.76.183.97 # for single IPs auto vmbr0 iface vmbr0 inet static address 144.76.166.100 netmask 255.255.255.255 bridge_ports none bridge_stp off bridge_fd 0 up ip route add 144.99.183.323/32 dev vmbr0 # for a subnet auto vmbr1 iface vmbr1 inet static address 144.76.166.100 netmask 255.255.255.248 bridge_ports none bridge_stp off bridge_fd 0 Thanks in advanced ! :)

  Read the article

• SMB super slow within LAN between MAC and PC

  - by asdcasdc

  I have a windows desktop which stores all my movies, songs and pictures. I have a mac laptop which I would like to access these files. I don't want to utilize the FTP or SCP protocol because I don't want them to be downloaded to my mac. I want to access them as if they are a network mounted disk. So I tried using the native SMB protocol (available in Finder - Go - Connect to server). I tried dragging a file and dropping it onto my MAC's desktop. Surprisingly, I am only able to transfer at a very slow rate of about 1mb/s. Assuming network connectivity is not a problem, has anyone experienced incredible slowness with SMB? Are there alternative protocols for me to use in this case between PC and MAC?

  Read the article

• WARNING Retrying Bulk Insert for file:sqlldr due to Communication Error:256

  - by user702295

  WARNING Retrying Bulk Insert for file:sqlldr due to Communication Error:256 I am running my engine on Linux and am receiving an intermittent message "WARNING Retrying bulk insert for file: sqlldr due to communication Error: 256" The engine seems to have completed successfully, but it is not clear if this error caused some of the forecast to not complete. It is also not clear what caused the error. Generally if you see only the WARNING of it, it means that next retries of the same load request have eventually succeeded and so the run a a whole is not affected. In order to know more about what happens, look for .log/.bad files left in the engines bin directory or possibly a quote of them within the specific engine log that had the issue.  The sqlnet.log file may also have some information about it and perhaps at the database server side there may be some log/alert regarding what happened.  Look at the alert.log. In general it could be that the database server/network was over loaded at the time and somehow the connection was rejected/failed/aborted either due to specific setting on concurrent connections/sessions or inadvertently due to glitch in network/os/hardware. If this repeats and becomes more frequent during the run you should look further into it as mentioned above. You can also track this using either SQL*Trace or java.util.logging.  - Globally enable logging by setting the oracle.jdbc.Trace system property java -Doracle.jdbc.Trace=true - Client Side Tracing: Your SQLNET.ORA file should contain the following lines to produce a client side trace file: trace_level_client = 10 trace_unique_client = on trace_file_client = sqlnet.trc trace_directory_client = <path_to_trace_dir> Server Side Tracing: To enable server side tracing, use the following parameters: trace_level_server = 10 trace_file_server = server.trc trace_directory_server = <path_to_trace_dir> Tracing Levels: The following values can be used for TRACE_LEVEL* parameters:     16 or SUPPORT — WorldWide Customer Support trace information     10 or ADMIN — Administration trace information     4 or USER — User trace information     0 or OFF — no tracing, the default Additional information is readily available via the web.

  Read the article

• Can't communicate with Primary DNS Server

  - by horsley

  A computer, with Windows 7, can't access any website by domain suddenly. Whether this computer use a wired link or connect to the WLAN, The fault persists IP and DNS obtained automatically, and seems normal (ipconfig /all return the correct info) I can visit websites by using HTTP proxy The DNS server is available, other computer in my room works properly. I can ping myself, the gateway and any other IP, but domains I can use nslookup and obtain the correct IP info There are some error information in the event log about dns client events explaining the client can not verify the DNS server available Windows network diagnosis explain that Windows can't communicate with the device or resource (Primary DNS Server) I guess the dns client should be blame. I tried to do the following things but the fault persist. Reinstall the driver of network adapter Reset TCP/IP (netsh int ip reset) Reset Winsock (netsh winsock reset) Reset LSP I don't want to reinstall the whole os, what should I do?

  Read the article

• How not to send all traffic over SBS connection?

  - by Niels R.

  Hi, My girlfriend uses SBS Connection Manager to connect to her company's network. The problem is that the internet connection is überslow at work, so she wants to use the home internet connection to surf the web and use the SBS Connection to get to her work stuff. Normally with a VPN connection you just have to uncheck a box "Send all traffic over VPN connection" or "Use VPN as default gateway" or something like that. As I've never seen this SBS Connection Manager-thing before, I've no idea where to uncheck a similar box. (I've checked the properties of the connection in Network Connections, but it only has a few options about logging and firewall). Thanks for any help in advance! Kind regards, Niels R.

  Read the article

• VPN or Remote Access?

  - by Craig Johnston

  In what circumstances would you setup a VPN instead of just allowing Remote Desktop to a machine in a network?

  Read the article

• Configuring NAT and static IP on Cisco 877W

  - by David M Williams

  Hi all, I'm having trouble setting up a static IP reservation on a network. What I want to do is assign IP 192.168.1.105 to MAC address 00:21:5d:2f:58:04 and then port forward 35394 to it. If it helps, output from show ver says Cisco IOS software, C870 software (C870-ADVSECURITYK9-M), version 12.4(4)T7, release software (fc1) ROM: System bootstrap, version 12.3(8r)YI4, release software I have done this - service dhcp ip routing ip dhcp excluded-address 192.168.1.1 192.168.1.99 ip dhcp excluded-address 192.168.1.200 192.168.1.255 ip dhcp pool ClientDHCP network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 192.168.1.1 lease 7 ip dhcp pool NEO host 192.168.1.105 255.255.255.0 hardware-address 0021.5D2F.5804 ip nat inside source static tcp 192.168.1.105 35394 <PUBLIC_IP> 35394 extendable However, the machine is getting assigned IP address 192.168.1.101 not .105 ... any suggestions? Thanks !

  Read the article

• Godaddy one page hosting

  - by liv a

  Disclaimer: not sure this is the right place for this kind of question, sorry in advance, just point me to the right place and I'll move it. In godaddy when paying only for domain, without hosting, they state you can get one page hosting for free but that option only opens their web-builder. I want to create a nicely design landing page, where the content is static.Is there a way to make my domain point to a wordpress one page or self created html one page/ landing page?

  Read the article

• Is there a way to disable the hardware on/off switch for the Wireless interface?

  - by avee

  I have an HP 520 and is running the latest Ubuntu 11.10. The hardware works fine with Ubuntu with one exception: The device has a hardware switch for turning the wifi on and off. Every time the wi-fi is disabled through the hardware switch, I am unable to bring it on again. The message on the networking popup would be device not ready. What I am looking for is a way to disable the hardware switch altogether so that when users accidentally press the button, the wifi would not be disabled. There is no setting to disable the switch in the BIOS. Hardware info from lspci -nn: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03) 00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 01) 00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) 00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01) 00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01) 02:06.0 CardBus bridge [0607]: ENE Technology Inc CB1410 Cardbus Controller [1524:1410] (rev 01) 02:08.0 Ethernet controller [0200]: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller Mobile [8086:1068] (rev 01) 10:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02) The output from lsmod | grep iwl: iwl3945 73329 0 iwl_legacy 71499 1 iwl3945 mac80211 272785 2 iwl3945,iwl_legacy cfg80211 172392 3 iwl3945,iwl_legacy,mac80211

  Read the article

• How do I decrypt WPA2 encrypted packets using Wireshark?

  - by Rox

  I am trying to decrypt my WLAN data with Wireshark. I have already read and tried eveything on this page but without any success (well, I tried the example dump on that page and succeeded, but I fail with my own packets). I caught the four-way handshake from another client connecting to the network. My network info is as follows: SSID: test Passphrase: mypass The above info would give this preshared key: 58af7d7ce2e11faeab2278a5ef45de4944385f319b52a5b2d82389faedd3f9bf In Wireshark in the Preferences--IEEE 802.11 I have set this line as Key 1: wpa-psk:58af7d7ce2e11faeab2278a5ef45de4944385f319b52a5b2d82389faedd3f9bf I have tried the different options of "Ignore the protection bit" but none works. What could I have missed?

  Read the article

• What equipment do real ISP's use?

  - by Allanrbo

  In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers?

  Read the article

• Group Video Chat On iPad With Fring App

  - by Gopinath

  Apple’s Facetime is the simplest and most easy to use video chat application available for iOS devices and Apple Macs. Facetime lets you have a one-to-one video chat, but what about having a group chat on your iPad with a bunch of friends? Here comes Fring App for iPad that lets you group chat up to 4 members at a time. Unlike Facetime Fring does not impose any restriction on the network connectivity for video chatting. You can initiate a group video chatting on any network (3G, Wi-Fi, 4G, etc.) but Wi-Fi is the most preferred option for smooth video streaming. Also Fring is a cross platform application(runs on iOS, Android & Nokia), so your group video chat session can have a mix of devices – iPads, Android smartphones/tablets and Nokia mobiles. Anyone mobile device with a front facing  cam and Fring app is allowed to join the party. Here is the promotional ad of Fring’s group video chatting application By the way did I say that Fring is a free app? Group video on iPad at no cost!!! Download Fring from Apple’s AppStore This article titled,Group Video Chat On iPad With Fring App, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• sniffing on a switched LAN

  - by shodanex

  Hi, I often find myself in the position of having to sniff on a connection between for example an arm board I am developing on, and another computer on the network, or out of the network. The easy situation is when I can install a sniffer on the computer talking to the embedded device. When it is not possible, I currently install an old 10Mb/s HUB. However I am afraid my HUB might stop working, and I would like to know some alternative. Here are the alternatives I could think of : Buy another HUB. Is that still possible ? Have some sort of ethernet sniffing bridge, like what they do for USB. I am afraid this kind of device is expensive. use ARP poisoning.

  Read the article

• Windows 2008 File Share

  - by user36540

  Hi, I have 3 Windows 2008 Standard servers in my system with no domain controller. Two of the servers are running a NLB cluster and the third server is a file server that the web servers connect to. I want to store my source code on the file server and point the IIS config to the network file share. The web sites also need access to a file share on the file server. I was able to share the network drive and access while logged into either of the web servers but my web apps are unable to access the file share - I assume due to permissions. Does anybody know the correct way to do this? Thanks, Chris

  Read the article

• Ubuntu on Pandaboard giving me troubles

  - by Jeroen Jacobs

  I'm trying to install the OMAP4 extras for ubuntu on my pandaboard. For some reason, a few packages can't seem to be agree with eachother. This what I did so far: installed on Ubuntu 11.10 on sd card Powered on Pandaboard and let it finish it's initial install Did an "apt-get update" and "apt-get upgrade", to install updates So far, everything went fine, and I was quite happy with my Pandaboard, but then I made the mistake of typing this: apt-get install ubuntu-imap4-extras At first, everything seemed ok, and it started downloading and installing. But then after a while it just crashed. I tried it again but then it gave me this: Reading package lists... Done Building dependency tree Reading state information... Done ubuntu-omap4-extras is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: gstreamer0.10-openmax : Depends: gstreamer0.10-plugins-bad but it is not going to be installed gstreamer0.10-plugin-ducati : Depends: gstreamer0.10-plugins-bad but it is not going to be installed ubuntu-omap4-extras-multimedia : Depends: gstreamer0.10-plugins-bad (>= 0.10.22-2ubuntu4+ti1.5) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). So I tried to the suggestion: apt-get -f install: Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: gstreamer0.10-plugins-bad The following NEW packages will be installed: gstreamer0.10-plugins-bad 0 upgraded, 1 newly installed, 0 to remove and 4 not upgraded. 88 not fully installed or removed. Need to get 0 B/1,794 kB of archives. After this operation, 4,571 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 143575 files and directories currently installed.) Unpacking gstreamer0.10-plugins-bad (from .../gstreamer0.10-plugins bad_0.10.22-2ubuntu4+ti1.5.4.8+1_armel.deb) ... dpkg: error processing /var/cache/apt/archives/gstreamer0.10-plugins-bad_0.10.22-2ubuntu4+ti1.5.4.8+1_armel.deb (--unpack): trying to overwrite '/usr/lib/libgstbasecamerabinsrc-0.10.so.0.0.0', which is also in package gstreamer0.10-plugins-good 0.10.30-1ubuntu7.1 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/gstreamer0.10-plugins-bad_0.10.22-2ubuntu4+ti1.5.4.8+1_armel.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Seems like two packages (plugins-good and plugins-bad) are fighting over the same library. Any idea on how to fix this??

  Read the article

• Can I turn my Mac Mini into a Wi-Fi Hotspot without additional tool

  - by user262325

  Hello everyone I have an app need to test via wifi. I just wonder if there is a way to turn my Mac Mini into a Wi-Fi Hotspot without additional tool. I try to setup airport new network name is"mymacmini'. My iPod Touch also can recognize the network "mymacmini". I set my iPod wifi as "mymacmini" But if I try to connect to Internet, Safari always reports failure and connnection with Wifi. I hope to know if I need purchase a wireless router for MAc Mini or there are something wrong I did above? Thanks interdev

  Read the article

• Clonezilla-SE with another DHCP Server in LAN

  - by aleroot

  I want to install Clonezilla-Server(192.168.1.100) in a network that already have a DHCP Server (dd-wrt with dnsmasq - 192.168.1.1). I've installed Clonezilla-SE on ubuntu Server 10.10, once installed and configured Clonezilla Server i've removed the DHCP-Server and set pxe server address in dnsmasq configuration on DHCP Server : dhcp-boot=pxelinux.0,,192.168.1.100 When i try to start from PXE a Computer in the network clonezilla start, but give me an error that the ipddress of the machine is not given by the clonezilla server and can't continue ... Someone has already tried to configure Clonezilla-SE in a similar enviroment? Is there some configuration on DRBL server of Clonezilla that i need to do ?

  Read the article

• Windows Firewall: How to allow traffic on port 8080?

  - by Chadworthington

  I am trying to configure team Foundation Server so that 1) it is accessible from within my Home Network 2) and then make the Web site access accessible via the Internet I have a problem with point 1: When I access http://192.168.1.106:8080/tfs/web/ locally from 192.168.1.106, it works. When I access the same web site from another PC in my home network, the abive URL works only if I turn of the Firewall on 192.168.1.106. Can someone please tell me specifically how to allow traffic on port 8080 without turning off Windows Firewall? It seems that the exceptions that I specify are intended for listing programs on the box that need to communicate out. Is IIS the program that I need to make the exception? How do I specify that port 8080 traffic should be allowed for web site traffic on this port? I hope to have success with pt. 2 later but I figure (1) should be done first. I expect issues.

  Read the article

• How can I force Parallels' networking to obtain an IP through a wireless router?

  - by RLH

  Here is my setup. I have a Macbook, Thunderbolt display and an Ethernet connection plugged into the Thunderbolt display. During the day, most of my network use can (and should) operate across the ethernet associated with my display. However, I also need to be able to connect up to a wireless router. This hasn't been a problem on the Mac OS X side, but the program that I need to run on the router has to obtain an IP address from the wireless access point. Considering my current setup, how can I leave it so that I can access the internet in OS X, yet have my Window 7 instance running in Parallels, get it's assigned IP address from a wireless router that my Mac is also connected to? I've fiddled around with the Parallel's network settings for an hour, and I can't get Parallel's to see the router, even though my Mac is certainly connected to it.

  Read the article

• Looking for a Software to harden Windows machines

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So IF anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• From the Tips Box: iPad Interface Emulation for Windows, Easy Access iPhone Flashlight, and Kindle Collection Management

  - by Jason Fitzpatrick

  Once a week we round up some of the great reader tips to share. Today we’re looking at an iPad interface emulator for Windows, a fast-access flashlight app for the iPhone, and a Windows-based way to organize Kindle collections. Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive Follow How-To Geek on Google+

  Read the article

• SQL 2008 R2 Named Instance Client Connectivity Issues?

  - by Jerry Dodge

  We're upgrading our software from using SQL 2000 to 2008 R2. Our customers will be installing an update which uninstalls 2000 and installs 2008 R2 under the same instance. So if no instance existed, then no instance name will be set (default). However, the problem starts with the customers which have a named SQL instance. Starting in 2008 R2 (not sure of ones before), for some reason, a client connecting to the server by its instance name is unsuccessful. I'm testing from the Management Studio - if I can't connect this, then nothing can connect. I browse network servers, and find the specific server\instance in the list. But, upon trying to connect to an instance name like MyServer\INST, I get: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) I do in fact have TCP/IP and Named Pipes protocols enabled, this is the first thing I did. When I connect to the server using a comma (,) and port number like MyServer, 49195, it works just fine. So it appears that client computers are just unable to identify the instance names. This has happened on all our installations of SQL 2008 R2 and from all client computers, including Win 7, XP, Vista, Server 2008, and Server 2003. We never experienced such issues on earlier versions of SQL. The problem even persists if the firewalls and antiviruses are all disabled. Now, this is a large update which we will be distributing soon to all our customers, and we want to minimize the interaction they need with us to get this installed. We absolutely hate the idea of using a port number, because it will always be different, and we would have to modify each client to point to this server/port. Some of our customers may have hundreds of client computers. How do I make client connections to a named SQL instance work again? After all, this is the whole purpose of named instances, and if a client can't connect to this instance by its name, then what is it even named for? EDIT It was mentioned to make sure SQL Browser is running, so I checked, and it is running. The server is also able to connect to its self (locally) - just external connections are refused. UPDATE After more careful checking, I learned the firewall wasn't completely disabled when testing, and upon disabling it completely, this works. So it appears that SQL Browser is being blocked by the firewall from external clients from accessing.

  Read the article

• Can't connect to VPN in Windows XP mode

  - by darkstar13

  I have Windows 7 x32 installed on my laptop. I have also Windows XP mode installed. My setup is that my work-remote programs are in Windows XP mode because my VPN installer in Windows XP only. Lately, I have been having troubles getting on / logging in to VPN. I can access the internet in WinXP mode but When I ping the IP address of the target IP of my VPN network (or even just Google.com), I always get a 'Request Timeout'. However, when I ping the same IP address in command prompt in Windows 7, I get 100% data sent. Is there anything I need to adjust? Before, I have been able to connect instantly. Now, it's like trial and error, or I will have to wait for hours just to be able to enter logon credentials in Cisco VPN dialer. NAT is my network adapter in XP mode.

  Read the article

• I have permanent connections to Canonical servers, what are they for?

  - by Dan Dman

  After the recent upgrade to 12, I notice permanent connections to canonical servers. Running netstat -tp gives: Foreign Address State PID/Program name mulberry.canonical:http CLOSE_WAIT 6537/ubuntu-geoip-p alkes.canonical.co:http CLOSE_WAIT 6667/python alkes.canonical.co:http CLOSE_WAIT 6667/python Why are there permanent connections and how could I stop this behavior? And if this is intentional, who is responsible? I would like to understand why this was done because to me it seems like a bad idea.

  Read the article

< Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >