Search Results

Search found 14236 results on 570 pages for 'times square'.

Page 426/570 | < Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >

• Hardware testing tool/suite

  - by Aviator

  Hi All, I just bought a new core i5 system (assembled) and started installing Windows 7. It was failing for many times and at some point got installed. After that, frequent crashes related to MEMORY. So checked the RAM using memtest86+ and found many errors.I got it replaced with the vendor and now if i install ANY OS, at some point in installation it either freezes completely with no response for hours, or restarts automatically. I tried installing Windows 7, Windows Vista and Ubuntu 9.10. I tested the new RAM again and found no problems in about 2 passes using memtest86+. I even updated the BIOS using bootable USB and even the problem persists. I am really not sure which hardware is causing trouble. I dont have any OS inside it, so i have to check using bootable CDs DVDs and USB only. Please advice on how to proceed. Are there any suites/ separate tools for checking integrity of each hardware parts and troubleshoot it? I wanted to confirm which part is problematic before going for replacement. Thanks a lot! This is the config: Core i5, MSI P55-GD65, GSKill 2x2GB, Seagate 500GB 7200rpm, CM Extreme 600W PSU, Saphhire Radeon 5770 1GB, LG DVD Writer

  Read the article

• Windows 7 not booting up and stuck at startup repair

  - by mikimr

  I've been having issues with Windows 7 Home Premium on a Lenovo laptop. At first, it would not start up normally at all. I started it in Safe Mode, where I disabled all non-MS services and tried again to no avail. It then goes into Startup repair where it failed several times. I tried copying the original registry settings, still the same. I resorted to booting with an Ubuntu DVD, where I ran the boot-repair, where it is supposed to correct the Windows boot. No luck. I used Win7 DVD to start up from there, where I had the option to install or repair. I chose the repair, got into command prompt, ran chkdsk /i /r, where it found 3 unreadable segments, went through the 2nd step without issues, and the 3rd step completed with some errors (can't recall the exact errors). When I restarted the machine, it went to straight to the Stratup Repair, indicating "Attempting repairs... Repairing dis errors. This might take over an hour to complete." It's been like this for nearly 15 hours. When I try to cancel or close the Startup Repair window, I get a message "The current repair operation cannot be cancelled." Should I let it run or force shut the machine? If force shut, how can I resolve this problem? Thanks.

  Read the article

• Are there any other causes of this error that are NOT related to initial setup?

  - by LordScree

  I'm trying to diagnose an issue at a customer site. They are receiving the following error: A network-related or instance-specific error occurred while establishing a connection to SQL Server I've seen this a few times, but only during the initial setup - it's often caused by one of the following: The database server is turned off The network connection between the database server and the application is closed or somehow blocked (e.g. a firewall) The SQL Server instance is not set up to receive remote connections from the application server (e.g. TCP is turned off, remote connections are disabled, or the "SQL Server Browser" service is stopped/disabled) However, if I assume that no configuration changes have been made, I'm trying to postulate on what the reason might be for getting this error at a random point after the initial setup. My initial thought is: SQL Server machine has run out of resources (e.g. RAM) and is unable to accept new requests from the application server Is this a valid theory? What other possible causes are there of this error that are not related to the initial setup of the server / application connection? Or is it simply impossible that this error could occur without a configuration change having been made (either on the SQL Server side, application side, or somewhere in-between (network))? NOTE: I believe this question differs from the plethora of questions related to this error message because the application and server have been talking to each other quite happily until now (most, if not all, other questions seem to relate to initial setup).

  Read the article

• PXELinux and compressed kernels/images

  - by Yvan JANSSENS

  Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

  Read the article

• Unusual HEAD requests to nonsense URLs from Chrome

  - by JeremyDWill

  I have noticed unusual traffic coming from my workstation the last couple of days. I am seeing HEAD requests sent to random character URLs, usually three or four within a second, and they appear to be coming from my Chrome browser. The requests repeat only three or four times a day, but I have not identified a particular pattern. The URL characters are different for each request. Here is an example of the request as recorded by Fiddler 2: HEAD http://xqwvykjfei/ HTTP/1.1 Host: xqwvykjfei Proxy-Connection: keep-alive Content-Length: 0 User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/534.13 (KHTML, like Gecko) Chrome/9.0.597.98 Safari/534.13 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 The response to this request is as follows: HTTP/1.1 502 Fiddler - DNS Lookup Failed Content-Type: text/html Connection: close Timestamp: 08:15:45.283 Fiddler: DNS Lookup for xqwvykjfei failed. No such host is known I have been unable to find any information through Google searches related to this issue. I do not remember seeing this kind of traffic before late last week, but it may be that I just missed it before. The one modification I made to my system last week that was unusual was adding the Delicious add-in/extension to both IE and Chrome. I have since removed both of these, but am still seeing the traffic. I have run virus scan (Trend Micro) and HiJackThis looking for malicious code, but I have not found any. I would appreciate any help tracking down the source of the requests, so I can determine if they are benign, or indicative of a bigger problem. Thanks.

  Read the article

• vmware player won't run on CentOS due to missing /dev/vmmon, what could be the problem?

  - by Graphics Noob

  So I've tried installing vmware player 3.1.4 and 3.1.3 and both times had the same problem, when I try to load a VM I get the error "Could not open /dev/vmmon". When I ls /dev/ I can see there is no "vmmon" device present. When I try running: sudo /etc/init.d/vmware start I get the output: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [FAILED] which shows that the Virtual Machine Monitor fails to load. I tried following the advice on this site and ran vmware-modconfig --console --install-all I notice during the compilation there are no errors, but at the end I get the message: Starting VMware services: VMware USB Arbitrator [ OK ] Virtual machine monitor [FAILED] Virtual machine communication interface [ OK ] VM communication interface socket family [ OK ] Blocking file system [ OK ] Virtual ethernet [ OK ] Unable to start services Out of curiousity I tried: sudo /sbin/insmod /lib/modules/2.6.18-238.9.1.el5xen/misc/vmmod.ko But got the error message: insmod: error inserting 'vmmon.ko': -1 Invalid module format I have a feeling this may be the root of the problem, but I don't know what could be causing it or how to fix it.

  Read the article

• Why does the Mac OS X firewall dialog recurringly pop-up and disappear by itself (without letting me

  - by Chris W. Rea

  From time to time, I'll be on my Macbook using a program that accesses the network – whether Firefox, or Sony's Reader Library – really, it seems like it could happen with any program that accesses the network – and for no reason that I can discern so far (that is, it happens intermittently) the OS X firewall dialog pops up to ask me the question: Except it doesn't actually let me click anything before it disappears! That is: the dialog pops up, ... then goes away by itself a second later, then pops up again, ... then goes away by itself a second later, etc. It happens a few times before stopping. It wouldn't be so maddening to be interrupted if I could just be allowed to click "Allow" and make the darn thing go away for good. In Security preferences I have the firewall turned "On", and I would like to keep it that way. Has anybody seen this problem, found the source, and figured out a solution or workaround? Thank you.

  Read the article

• Sendmail slow to accept emails

  - by Rich

  I have a PHP web app which is using SMTP to sendmail on localhost to send email. I would like sendmail to accept the mail request immediately and queue it for later sending, as I don't want to have user-facing request threads blocked on emails. Sendmail is installed with the default settings on RHEL web servers. Sometimes sendmail is blocking for a long time after the MAIL command is sent -- sometimes taking 60 or 90 seconds to accept the mail. The time take is usually very close to 60 or 90 sec, which makes me think this is some kind of timeout. I have looked in the sendmail logs, and there are plenty of "deferred" emails, but nothing which looks responsible for this delay. How can I diagnose what is slowing down sendmail? How can I configure sendmail to always accept the mail immediately and to queue the mail for later sending? Update: I'm not sure, but it looks like this might be linked to aol.com addresses. I strongly suspect that sendmail is doing some kind of blocking receipient address verification at the accept-email-for-sending stage. How can I disable that, so that sendmail doesn't block my UI threads? Update 2: This only seems to happen at busy times. Perhaps I am running out of sendmail threads or something? How can I check that?

  Read the article

• Giving the root user priority to maintain Debian (while server collapsing under heavy load)

  - by Saix

  Is there any way to setup Debian to prioritize any or specific root's activity before every other? For instance, several times per year something gets wrong (usually man's fault by overstressing apache/mysql) and system gets unresponsive under heavy load like 200 (8-core cpu). I know there are limits for php scripts to run then kill, but that's not the way because this limit has to be at least 45 minutes long. The problem is, until I'm able to login via SSH and let apache/mysql restart under this server stress, it nearly hits these 45 minutes anyway. Also hardware restart causing usually to run fsck at boot time on all harddrives since it's usually pretty long the box haven't been restarted. I was told it's really not good idea disabling fsck but then again, it takes more then hour to complete. What is the fastest way to restart apache/mysql? Is there any way to give ssh users or root user higher priority so the logging in and completing these restarts (rather stops though) commands wouldn't take so long? One comes to my mind.. use NICE for apache/mysql but no way. I can't risk limiting those two vital apps 24/7 or could I? I'm a little bit scared if any other system process wouldn't slow the pages down too much. Any backup process, swap (if any) etc. There is pretty heavy PHP framework with 20k visits a day, so it needs every hw/sw resource available. I can't throttle it the whole time, just in certain points when system gets unresponsive, so I could maintain it.

  Read the article

• Computer freezes after watching Youtube videos

  - by Roberts

  I had Windows 7 installed all september. But I installed Windows XP Professional back because my computer couldn't handle the new OS. After first boot I tried to install newest flash player (from Adobe website), but it failed. I had my old setup on USB drive and it worked. I don't know is it important or not. I am watching Youtube videos in my free time (almost every hour). After few days the computer started to freeze when I open a page with the video or close the page with video, not while I watch a video. No BSODs. Nothing in Event viewer. I use Firefox only. When computer freezes the sound wont. If iTunes is playing a radio station or is it another video playing in background, the sound wont freeze. Last few days the mouse wont freeze. Its a strange symptom. If I click few times then the cursor will actually freeze. I just want to know where does this problem come from (hardware - graphics card, old motherboard or it's just some glitch in setups). If it's not graphics card then I will be happy. The graphics card is ATI Radeon HD 4650 - brand new. Catalyst 11.8 installed. Things I have tried: Installed newest flash player after a week (the setup didn't fail this time) Installed latest video drivers Deleting cookies Defragmenting hard drive Using TuneUp utilities for computer cleenup Installed latest Mozilla Firefox Cleaned the PC Changed CPU Fan speed almost to max (just to be sure) Things I haven't tried yet: Didn't try playing videos on other browsers What can I do now?

  Read the article

• Linux Centos 6 becomes unavailable from time to time - OS&network issue

  - by adoado0

  I am encountering following problem. There is one server (DL160 G5) running Centos 6.3 with default kernel 2.6.32-220.2.1.el6.x86_64 - at this point I'd like to add that issue appeared also at older version - 6.1 and older kernel (do not remember exactly which version). There is cPanel installed and from time to time it becomes unavailable (network connection). What I've checked is (via KVMoIP): load average is completely normal it does not lack memory or disk space when problem occurs no console notifications checked all access logs and there is no sign that it can be caused by a client script cannot even access local interface (127.0.0.1) or main IP address running tcpdump I can only see packets arriving to server - no responses all services seem to be running properly (mail,sql,http,ssh) checked crontab and all clients' crontabs too network port utilisation is low ( up to several Mbits) arriving packet rate is low - hundreds per second (according to tcpdump) console (via kvmoip) works fine, no lags there is no conntrack at this server there is no ipv6 at this server flushing iptables, unloading modules does not resolve problem restarting network does not resolve problem, no errors appear it also occurs when two sepearate networks are configured (and multiple gateways) as well as one IP, one default gw and one network is configured - so it seems network configuration independent it seems to repeat randomly (load,packet rate,bandwith usage,load independent) checked server with different rootkit detection tools - it seems to be clean server has been rebooted, it did not change anything there are no interface errors it apperas randomly can be once a week or several times per day It usually works fine after 1-15 minutes. What I can also check? It is definitely OS issue - there is traffic at interface only in one direction when problem occurs, can not even ping loopback. Any ideas? Recommended checks? Anything I did not checked above.

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Hi - Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message : "Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions? Many thanks Clem

  Read the article

• Why does my ftp(e)s server fails like half of the time

  - by user1092608

  I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

  Read the article

• My laptop screen keeps dimming

  - by Rowland

  I have a Cryo laptop with Windows 7 installed, bought in December 2011. Sometimes the screen seems to persistently dim and/or brighten up, even as I am doing things. In fact the brightness is varying even as I type this. The battery is always fully charged and connected to the mains. I have checked many times the battery/power-saving settings always leaving the settings the same way; full brightness and never dimming when on the mains. Yet when the screen starts playing up I can end up with the screen dimming and brightening almost continuously. I once went to the "adjust screen brightness" window when the screen had dimmed. I found the brightness slider on 100% (as I expected) but, as I dragged it to the left, to dim the screen, it first brightened and then started dimming, i.e. the screen setting said 100% brightness but it was only at, maybe 80%. I have checked with Cryo and they just say check the power settings. I know what these are and how to work them and always set them to never dim/full brightness, yet still my laptop starts this dimming every so often.

  Read the article

• How can see what processes makes my server slow?

  - by Steven

  All my websites on my server are extremely slow or not loading at all. Even server admin (Plesk) will not load some times. There's been no changes to the sites for the last coupple of months. How can I see what processes is making my server slow? My environment looks like this: Server: VPS running Linux 2.8.x OS: Centos 5 Manage interface: Plesk 9.x Memmory: 1024MB CPU: 2.2GHz My websites run on PHP and MySQL. I finally managed to telnet (Putty + SSH) in to my server. Running top did not show any processes using more than max 2% CPU and none were using exesive memmory. I also got a friend to install a program that checks the core files, and all seemed fine. So I'm leaning towards network issues or some other server malfunction. But I'm not able to find out what can be wrong. Here are some answers to Sean Kimball: I don't run mail services on my server yet There are noe specific bandwidth peaks. Prefork looks like this <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> Not sure what you mean with DNS question. But I think it's up and running. There are no processes running wild Where can I find avarage load? Telnet is disabled and I have to log in using SSH :)

  Read the article

• How to Access User Directory shared by Apache on OS X Mountain Lion?

  - by schluchc

  When trying to access the local user web page on localhost/~username, I get a "403 Forbidden". The system web page in /Library/WebServer/Documents is accessible on localhost/ though, so I assume Apache is working fine. I know that this problem has been discussed several times, also on superuser. I implemented and checked all I could find, but I still couldn't solve the problem and would be glad if someone had a suggestion for this particular case: sudo apachectl -t returns Syntax OK. I have a username.conf file in /etc/apache2/users/: <Directory "/Users/username/Sites/"> Options Indexes MultiViews FollowSymLinks AllowOverride AuthConfig Limit Order allow,deny Allow from all </Directory> as proposed here [SuperUser] and in several other tutorials. The permissions of the username.conf file are -rw-r--r-- root wheel, as they should be. The httpd.conf is unchanged and therefore contains the line Include /private/etc/apache2/extra/httpd-userdir.conf. That file in turn contains UserDir Sites Include /private/etc/apache2/users/*.conf <IfModule bonjour_module> RegisterUserSite customized-users </IfModule> So the httpd*.conf files should be ok. The permissions of /Users/username/Sites is drwxr-xr-x 10 username staff and -rw-r--r--@ 1 username staff for the index.html. In the error log I simply get a [Sun Nov 25 22:14:32 2012] [error] [client 127.0.0.1] (13)Permission denied: access to /~username/ denied. And yes, after each change I did the sudo apachectl restart. Any help no how to solve the problem or how to further analyze it would be highly appreciated!

  Read the article

• Is there a 'global media cache' in Windows 7 that may be used by third party media players?

  - by Pulse

  Here's the background. I don't use Windows Media Player or Media Centre, in fact both components have been 'turned off' via the 'Programs and Features' option. My media player of choice is a nightly build of MPC-HC, which plays virtually everything. I do, however, have VLC portable available for those rare instances when MPC-HC can't or won't play something correctly. This is the situation. I tend to download various media files via torrent, typically, game trailers or freely availably films, such as the recently released, torrent only, Pioneer One. Quite often these files are quite large, being 1GB+ so I quite often like to preview the file after it has downloaded a significant portion of the file. For the most part, this works quite well, and gives me an idea about the worth of continuing the download. Sometimes, however, the file doesn't play as expected and instead plays a completely unrelated file that has been previously played. Here's the strange thing. if I try to preview the file in MPC-HC or VLC both players play the same, previously played file, regardless of whichever player was originally responsible for playback. Most times, it's not even a file that's been played recently. I have searched the registry for some sort of MRU cache, but have found nothing. I have made sure each player has had it's respective history/cache deleted and can fine nothing on disk that seems to be storing this, apparently shared data. So, the question is, where are these unrelated players getting the file information from? Thnaks.

  Read the article

• mail server checklist..

  - by Jeff

  currently we ran into some issues with our mail server setup. im preparing a list of actions that we should enforce and use in order to maintain a proper email solution within our company. we have around 80 exchange users, and send mass emails out almost on a monthly bases to 20,000 + customers each time.. the checklist i currently have: 1) mcafee mxlogic 'cloud' anti-spam functionality for incoming message. 2) antivirus on each computer in company 3) antivirus on exchange and DNS servers 4) setup SPF record 5) setup DKIM 6) setup domainkey 7) setup senderID 8) submit spf to microsoft, yahoo, etc. for 'whitelist' purposes. 9) configure size limits for messages in exchange to safe numbers 10) i have 2 outside IPs for my email server, incase one gets blacklisted, switch to the backup. 11) my internet site rests on a different ip than the mail server 12) all mass emails for company sent through 3rd party company (listtrak.com) 13) setup domain alias, media, enews, and bounce for the 3rd party mass mail software. 14) verify the setup using [email protected] 15) configure group policy and our opendns.org account to prevent unwanted actions and website viewing mass emails: 1) schedule them to send different amounts at different times (1,000 at 10am, 1,000 at 4pm, 1,000 10am next day).. 2) setup user prefences, decide what they want to receive ect. ( there interests) 3) send a more steady flow of email, maybe 100 a week with top new products instead of 20,000k every other month.. if anyone has suggestions or additions/subtractions to this checklist they are greatly appreciated. thank you

  Read the article

• Multi-partition USB stick

  - by nightcracker

  In my freelance job as "the dude that fixes your computer" I have an extremely handy tool, a bootable USB stick with Ubuntu LiveCD that allows me to recover and investigate in a known, working environment. Now, I want to reformat this USB stick and reinstall with Casper-RW persistance. I did this a few times before with a FAT-formatted USB stick. It was a horror. The USB drive corrupted constantly, by people accidently removing the USB stick, the computer not properly shutting down, ETC. Now what I want to create a multi-partition USB stick so I can put Ubuntu on a ext partition, but still be able to store some Windows stuff in it, by having a secondary FAT partition. However I read somewhere that Windows will only check the first partition on USB sticks, giving a problem with the first bootable linux partition. Is this possible on some way? EDIT Perhaps it wasn't clear what the problem is. The problem is that I read somewhere that Windows will only recognize the first partition on a USB stick. But I want two partitions, a ext partition and a FAT partition. No issues so far, but in order to be bootable the ext partition must be the first one!

  Read the article

• Understanding ulimit -u

  - by tripleee

  I'd like to understand what's going on here. linvx$ ( ulimit -u 123; /bin/echo nst ) nst linvx$ ( ulimit -u 122; /bin/echo nst ) -bash: fork: Resource temporarily unavailable Terminated linvx$ ( ulimit -u 123; /bin/echo one; /bin/echo two; /bin/echo three ) one two three linvx$ ( ulimit -u 123; /bin/echo one & /bin/echo two & /bin/echo three ) -bash: fork: Resource temporarily unavailable Terminated one I speculate that the first 122 processes are consumed by Bash itself, and that the remaining ulimit governs how many concurrent processes I am allowed to have. The documentation is not very clear on this. Am I missing something? More importantly, for a real-world deployment, how can I know what sort of ulimit is realistic? It's a long-running daemon which spawns worker threads on demand, and reaps them when the load decreases. I've had it spin the server to its death a few times. The most important limit is probably memory, which I have now limited to 200M per process, but I'd like to figure out how I can enforce a limit on the number of children (the program does allow me to configure a maximum, but how do I know there are no bugs in that part of the code?)

  Read the article

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• Wildcard subdomain setup ... want to change host IP throws off client A records... what to do...

  - by Joe

  Here is the current set up (in a nutshell). The site is set up with a wildcard subdomain, so *.website.com is accessible. Clients can then domain map their own domains with an A record to the server IP address and it will translate the to appropriate *.website.com with re directions and env variables in htaccess. Everything is working perfect... but now comes the problem. The site has grown larger than a single DQC Xeon server can handle at peak times. Looking at cloud options seems tempting, but clients are pointing their domains to a single IP address with the A record (our server). Now, this was probably bad planing from the start, but the question is, if this was to be done today, how would we set it up so that clients use a CNAME perhaps to point their domains to our server rather than an A record. And, if that is not possible for the root domain, how can we then use multiple IP addresses on our side to translate the incoming http request? Complex enough? Hope I've explained it well!

  Read the article

• can't install anything anymore with apt-get

  - by Aymane Shuichi

  Welcome this is the log I have when trying to install anything (php5-fpm after removing it) apt-get install php5-fpm Reading package lists... Done Building dependency tree Reading state information... Done php5-fpm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up php5-fpm (5.4.4-14+deb7u10) ... insserv: warning: script 'S55IptabLes' missing LSB tags and overrides insserv: warning: script 'S55IptabLex' missing LSB tags and overrides insserv: There is a loop between service IptabLes and mountnfs if started insserv: loop involving service mountnfs at depth 8 insserv: loop involving service networking at depth 7 insserv: loop involving service mountnfs-bootclean at depth 10 insserv: There is a loop between service rc.local and mountall if started insserv: loop involving service mountall at depth 6 insserv: loop involving service checkfs at depth 5 insserv: loop involving service kbd at depth 11 insserv: There is a loop between service rc.local and mountall-bootclean if started insserv: loop involving service mountall-bootclean at depth 7 insserv: loop involving service urandom at depth 9 insserv: There is a loop between service IptabLes and mountdevsubfs if started insserv: loop involving service mountdevsubfs at depth 2 insserv: loop involving service udev at depth 1 insserv: There is a loop at service rc.local if started insserv: There is a loop at service IptabLes if started insserv: Starting IptabLes depends on rc.local and therefore on system facility `$all' which can not be true! (x99 times repeated ) insserv: Max recursions depth 99 reached insserv: loop involving service postfix at depth 2 insserv: There is a loop between service IptabLes and udev if started insserv: loop involving service mountkernfs at depth 1 insserv: loop involving service IptabLes at depth 1 Now here is the error i get insserv: exiting now without changing boot order! update-rc.d: error: insserv rejected the script header dpkg: error processing php5-fpm (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: php5-fpm E: Sub-process /usr/bin/dpkg returned an error code (1) The biggest operation I held before this was updating nginx from 1.2 to 1.6 and it was thanks to this site : here is the link : How to upgrade nginx from 1.2 to 1.6 on debian 7 Please help !

  Read the article

• How expensive is a hostname in htaccess? Other solutions possible?

  - by Nanne

  For easy allow or disallowing of dynamic IP-adresses you can add them as a hostname in a .htaccess file. As I have read from: .htaccess allow from hostname? it does a reverse lookup on the connecting ip address, seeing if the response matches the allowed name. (Well, actually Apache is doing a double lookup, first a reverse lookup and then a forward lookup on the result of the reverse.) This is the reason we are currently not using dynamic-ip hostnames in the .htaccess: this "sounds" quite heavy: 2 extra lookups for every request. Is this indeed quite heavy, and would a reasonably busy server that is rather looking for less then more load get away with this :)? (e.g.: how does this 'load' compare to the rest? If a request is 1000 times more expensive then the lookups it might be negligible. otoh, it could be that final straw :) ) Are there other solutions? I can write a script that does a lookup of the hostname and put it in .htaccess files ofcourse, but this feels a bit like a hack.

  Read the article

• Power surge PC damage: How can I test all components of my PC without access to a second computer?

  - by Doug T.

  Ever since we had some crazy power surges last week my 64 bit Windows 7 PC has been acting strange. My USB network adapter disconnects from the wireless and can't detect the signal. I have to disable/reenable the adapter to detect it again. Also my wife has reported that the PC has rebooted a few times while I'm not sitting at it. Today I finally caught the reboot while I was using the PC. I got this blue screen of death. Stop Code 0x00000109: "Modification of system code or a critical data structure was detected." I followed the advice at the linked article and ran a memory test. I used memtest86 and its already found around 300,000 errors out of 8 gigs of ram. Now I'm worried -- what are the odds this is isolated to just my memory and not just a system wide problem? Isn't there a good chance that many other components are fried? More importantly, how can I test those other components? Are there tools similar to memtest I can use to test my motherboard/video card/power supply? If these are vender specific, is it typical for vendors to provide testing tools?

  Read the article

< Previous Page | 422 423 424 425 426 427 428 429 430 431 432 433  | Next Page >