Search Results

Search found 13469 results on 539 pages for 'avoid trouble'.

Page 429/539 | < Previous Page | 425 426 427 428 429 430 431 432 433 434 435 436  | Next Page >

• Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

  - by Max Kosyakov

  Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

  Read the article

• Windows XP installation problems

  - by Samurai Waffle

  I recently asked a question on here, and thought I had it working... Here is a link to it. Windows XP Installation problems So basically I'm having trouble getting XP installed. To sum it up, a computer I have had a boot sector virus, and I used Darik's Nuke and Boot to wipe the hard drive clean. So the hard drive has nothing on it. I had to try and install Windows through a DOS prompt, because for some reason it won't read it off the DVD. The UBCD is able to look at the files located on the DVD I have in, but I can't boot from it for some reason. So I extracted it to a USB drive, booted to DOS and started the setup process. Here's the weird thing with DOS... It can only find the C: drive. The C: drive in DOS is the flash drive that I have in, running DOS. I can't find the hard drive anywhere! So anyways, after starting the setup process, it copied the files over to the "hard drive" (which took 16 hours because the version of DOS I ran couldn't run smartdrv.exe), and it said the computer had to reboot. So I let it reboot, and it stopped and said there is no boot device. So I popped in UBCD that I have installed on a flash drive, and I discovered that it had copied the Windows files over to the flash drive and not the hard drive. It never asked where it should extract the files... So I toyed around with UBCD, ran a memory test on the hard drive to make sure it was fine, and it came out clean. So I'm stuck now. How can I get this installed? Writing this, I came up with an idea. If I copy the DOS startup files over to the hard drive, would I be able to start DOS from it? If so, I believe that could fix my problems. Any help is greatly appreciated, because I am running out of ideas and am at my wits end with this computer.

  Read the article

• Handling site not found and page not found with dynamic mass virtual hosting

  - by Rick Moynihan

  I have recently setup mass virtual hosting in Apache so that all we need to do is create a directory to create a new vhost. We're then also using wildcard DNS to map all subdomains to the server running our Apache instance. This works excellently, however I'm now having trouble configuring it to fail-over to an appropriate default/error-page when the vhost directory does not exist. The problem appears to be conflated between by my desire to handle the two error conditions: vhost not found i.e. there was no directory found matching the host supplied in the HTTP host header. I'd like this to display an appropriate site not found error page. The 404 page not found condition of the vhost. Additionally I have a specialised "api" vhost in its own vhost block. I've tried a number of variations and none seem to exhibit the behaviour I want. Here's what I'm working with right now: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /var/www/site-not-found ServerName sitenotfound.mydomain.org ErrorDocument 500 /500.html ErrorDocument 404 /500.html </VirtualHost> <VirtualHost *:80> ServerName api.mydomain.org DocumentRoot /var/www/vhosts/api.mydomain.org/current # other directives, e.g. setting up passenger/rails etc... </VirtualHost> <VirtualHost *:80> # get the server name from the Host: header UseCanonicalName Off VirtualDocumentRoot /var/www/vhosts/%0/current # other directives ... e.g proxy passing to api etc... ErrorDocument 404 /404.html </VirtualHost> My understanding is that the first vhost block is used as the default, so I have this here as my catch all site. Next I have my API vhost, and then finally my mass vhost block. So for a domain that doesn't match the first two ServerName's and has no corresponding directory in /var/www/vhosts/ I'd expect it to fall-over to the first vhost, however with this setup, all domains resolve to my default site-not-found. Why is this? By putting the mass-vhost block first, I can get the mass-vhosts to resolve properly, but not my site-not-found vhost... and in this case I can't seem to find a way to distinguish between a page-level 404 in the vhost, and the case where the VirtualDocumentRoot fails to find a vhost directory (this appears to use the 404 also). Any help out of this bind is much appreciated!

  Read the article

• Problems migrating an EBS backed instance over AWS Regions

  - by gshankar

  Note: I asked this question on the EC2 forums too but haven't received any love there. Hopefully the ServerFault community will be more awesome. The new AWS Sydney region opening up is something that we've been waiting for for a long time but I'm having a lot of trouble migrating our instances over from N. California. I managed to migrate 1 instance over using CloudyScripts to move a snapshot and then firing up a new instance in the Sydney region. This was a very new instance so both the source and destination were running on a Ubuntu 12.04 LTS server and I had no issues there. However, the rest of our instances are all Ubuntu 10.04 LTS and with these, I'm having a lot of problems. I've tried following: 1- following the AWS whitepaper on moving instances which was given to us at the recent Customer Appreciation Day in Sydney where the new region was launched. The problem with this approach was with the last step (Step 19) here you register the image: ec2-register -s snap-0f62ec3f -n "Wombat" -d "migrated Wombat" --region ap-southeast-2 -a x86_64 --kernel aki-937e2ed6 --block-device-mapping "/dev/sdk=ephemeral0" I keep getting this error: Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' does not exist which I think is due to the kernel_id not existing in the Sydney region? 2- Using CloudyScripts to move a snapshot and then creating a new volume and attaching to a new instance in Sydney This results in the instance just hanging on boot and failing the status checks. I can't SSH in or look at the server log I suspect that my issue is with finding the right kernel_id for the volume in the new region. However I can't seem to work out how to go about finding this kernel_id, the ones I've tried (from the original instance) don't result in the Client.InvalidAMIID.NotFound: The AMI ID 'ami-937e2ed6' error and any other kernel_id just won't boot. I've tried both 12.04 and 10.04 versions of Ubuntu. Nothing seems to work, I've been banging my head against a wall for a while now, please help! New (broken) instance i-a1acda9b ami-9b8611a1 aki-31990e0b Source instance i-08a6664e ami-b37e2ef6 aki-937e2ed6 p.s. I also tried following this guide on updating my Ubuntu LTS version to 12.04 before doing the migration but it didn't seem to work either, still getting stuck on updating the kernel_id http://ubuntu-smoser.blogspot.com.au/2010/04/upgrading-ebs-instance.html

  Read the article

• Problem connecting to SSH in office network

  - by Jeune

  I have trouble connecting via SSH to a server whenever I am in the office. I get as far as being prompted for my password and then after that there's a long wait which always ends in a Write failed: Broken pipe This is only for connecting via SSH. I use svn to commit files to a repository hosted on the same server and there are no hitches. Furthermore, this only happens in our office. When I go the university or whenever I am at home or at the coffee shop I am able to connect seamlessly. There are no firewalls in our office. It's just a basic wireless router connected to a modem setup. It's the same setup I have at home and I guess the same setup in the coffee shop. What are the causes for a broken pipe and why does this phenomenon only happen when I try connect via SSH and not when I work with svn on the same server? Updated: Some debug logs after authentication: debug3: packet_send2: adding 48 (len 64 padlen 16 extra_pad 64) debug2: we sent a password packet, wait for reply debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ORBIT_SOCKETDIR debug3: Ignored env SSH_AGENT_PID debug3: Ignored env TERM debug3: Ignored env SHELL debug3: Ignored env XDG_SESSION_COOKIE debug3: Ignored env WINDOWID debug3: Ignored env GNOME_KEYRING_CONTROL debug3: Ignored env GTK_MODULES debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env LIBGL_DRIVERS_PATH debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env DEFAULTS_PATH debug3: Ignored env SESSION_MANAGER debug3: Ignored env USERNAME debug3: Ignored env XDG_CONFIG_DIRS debug3: Ignored env DESKTOP_SESSION debug3: Ignored env LIBGL_ALWAYS_INDIRECT debug3: Ignored env PATH debug3: Ignored env PWD debug3: Ignored env GDM_KEYBOARD_LAYOUT debug1: Sending env LANG = en_PH.utf8 debug2: channel 0: request env confirm 0 debug3: Ignored env GNOME_KEYRING_PID debug3: Ignored env MANDATORY_PATH debug3: Ignored env GDM_LANG debug3: Ignored env GDMSESSION debug3: Ignored env SHLVL debug3: Ignored env HOME debug3: Ignored env GNOME_DESKTOP_SESSION_ID debug3: Ignored env LOGNAME debug3: Ignored env XDG_DATA_DIRS debug3: Ignored env DBUS_SESSION_BUS_ADDRESS debug3: Ignored env LESSOPEN debug3: Ignored env WINDOWPATH debug3: Ignored env DISPLAY debug3: Ignored env LESSCLOSE debug3: Ignored env XAUTHORITY debug3: Ignored env COLORTERM debug3: Ignored env OLDPWD debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 UPDATE 2011-14-07: I am able to connect to the server via SSH now. I didn't do anything but that's because there is no one in the office but me! Having said that, is it possible that it has something to do with the number of sessions an SSH server can handle? UPDATE 2011-14-07: I try to login via SSH through Putty on another machine running windows together with my current SSH session in Ubuntu and now it seems my SSH session in Ubuntu has been dropped. I can't type into the terminal. Is Putty the culprit now?

  Read the article

• Powershell: Cannot connect via SSL

  - by JSWork

  Am following "secrets to powershell remoting" to setup an SLL account and seem to be missing a step. I ran Winrm create winrm/config/Listener?Address=*+Transport=HTTPS @{Hostname="redacted";CertificateThumbprint="redacted"} and got PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1184937132 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1184937132 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 5985 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1187163138 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1187163138 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 80 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_220862350 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_220862350 Name Value Type ---- ----- ---- Address * System.String Transport HTTPS System.String Port 5986 System.String Hostname redacted System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint redacted System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String Trouble is when i do this PS C:\Users\redacted> enter-pssession -Computername redacted -Credential redacted\redacted -UseSSL I get this Enter-PSSession : Connecting to remote server failed with the following error message : The client cannot connect to th e destination specified in the request. Verify that the service on the destination is running and is accepting requests . Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or Win RM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". For more information, see the about_Remote_Troubleshooting Help topic. At line:1 char:16 + enter-pssession <<<< -Computername redacted -Credential redacted\redacted -UseSSL + CategoryInfo : InvalidArgument: (redacted:String) [Enter-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CreateRemoteRunspaceFailed This happens even when the firewall is off completely and when the machine tires to connect to itself locally. On top of that, despite the listners eing lsited on wsman, when I run PS WSMan:\localhost&gt; Get-PSSessionConfiguration I get Name PSVersion StartupScript Permission ---- --------- ------------- ---------- Microsoft.PowerShell 2.0 PS WSMan:\localhost&gt; Any ideas what I'm missing/doing wrong? edit: Windows 2003. Powershell v2.0

  Read the article

• Computer experiencing slowdowns and lockups despite low cpu useage

  - by user157145

  my setup i5-2300 nvidia gtx 550 ti 6 gigs ram 600 w ocz modular psu recently reformatted and already experiencing drastic slowdown as soon as windows comes up, including repeated lockups with multiple various programs reporting that they are not responsive, then recovering after 10-30 seconds. ive checked memory and hard drive both of which come out fine. despite my plethura of worthless antiviral software im forced to assume that my illicit downloading practices have lead me into some comp trouble that i cant seem to determine. i have used ccleaner, search and destroy and malware bytes, all of which have found nothing to indicate what is causing this massive slowdown. in addition according to my resource manager my computer is operating at a load of only 30-50 percent CPU useage and 60 ram useage but taking 5-10 seconds to load files and open folders, and repeated lockups of multiple programs, especially firefox which seems to go unresponsive every 2-3 minutes. any help would be appreciated, i used a program called OTL by old timer, but cant make any sense of the results i was given. any help or suggestions would be appreciated, thank you for taking the time to read this i have avast but it didnt even find anything when i had it do a full system scan, so im thinking its clueless(also nortons, avg, and ad-aware). i also have mse but it has yet to complete a full scan it takes so long (i left it on last night but when i woke up my computer had a problem and had to restart). my hard drive has 300 gigs out of 1tb open and i already used hd tune pro, which said my harddrive was fine and its not a ssd. also im a noob at comps and only have the hd that is currently inside the computer in addition im not sure if studdering is the issue im suffering. my problem is that during my typing of these responses firefox has gone "not responsive" at least 5 times, each for times of about 5-10 seconds. when i try to control alt delete to bring up windows task manager it took 20 seconds. essentially its that my computer goes super slow at bringing up anything, or taking any action whatsoever that opens a program or file and has repeated incidents where i cant even click on whatever im trying to do because it locks up. the confusing thing about these incidents is that its right after restarting where there are minimal programs running and the computer and memory load is light.

  Read the article

• HAproxy roundrobin balancing does not appear to be distributing evently

  - by andrew

  Hello, I know that with loaded servers, roundrobin in HAproxy (1.4.4) does not evenly distribute, but my servers are currently getting NO traffic (test setup), and roundrobin balancing does www1,www1,www1,www1,www1,...www2,www2,www2,...,www1... I'm verifying this by having the script being run on each server cat /etc/HOSTNAME (slackware). I need to have it switch back and forth each time to test some session stuff (stored in shared memcached) but am having trouble getting it to switch between my two web servers on each request. global log 127.0.0.1 local0 warning maxconn 4096 chroot /usr/share/haproxy pidfile /var/run/haproxy.pid uid 99 gid 99 daemon defaults balance roundrobin fullconn 100 maxconn 4096 mode http option dontlognull option http-server-close option forwardfor option redispatch retries 3 timeout connect 5000 timeout client 20000 timeout server 60000 timeout queue 60000 stats enable stats uri /haproxy stats auth ***:*** frontend www *:80 log global acl is_upload hdr_dom(host) -i uploads.site.com acl is_api hdr_dom(host) -i api.site.com acl is_dev hdr_dom(host) -i dev.site.com acl is_apidev hdr_dom(host) -i apidev.site.com use_backend uploads.site.com if is_upload use_backend api.site.com if is_api use_backend dev.site.com if is_dev !is_apidev default_backend site.com backend site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend api.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:api.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend dev.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:dev.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend uploads.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:uploads.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 backup weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 So basically, I have some different back-ends (I've verified the ACLs are working), with the default option "roundrobin" selected. I've tried removing weights, removing the minconn/maxconn/fullconn attributes for all servers (not just the backend I'm testing), tried removing the ACLs, etc. I've been testing on dev.site.com BTW. Anyone see a reason why I can't get something like www1,www2,www1,www2,...? Also, this is one of my first questions on here, so please let me know if I left anything needed out of my post. Thanks!

  Read the article

• Hanging page loads every n loads - SOLVED

  - by Christian

  Hi Guys I recently moved my site to a new server (Apache 2, PHP5, MySQL5). The site is an Invision based forum. Every few posts / topics it just hangs. The data has been written because if you stop and reload, the post / thread is there. I thought it was a write issue initially, but nope. So, the data is written but the page load never completes. It doesn't leave the page where the data has been input. Whats the best way to trouble shoot this issue? The only thing I have done recently is reduce my MySQL timeouts, but I can't see that being an issue as the values are still big enough and there are no mentions of timeouts in the MySQL log. (For the record there is nothing in PHP's error log either) Thanks in advance! EDIT: I checked my server-status. It all looked ok, but I have a suspicion I was hitting my ServerLimit, so I doubled that. Also enabled my Keepalives. Will keep an eye on it. EDIT 2: Its now been a few days and this is still occuring. I have more info though; Apache is throwing seg faults, but enabling core dumps does not produce them. I have tried disabling the modules in apache but it just stops things from working. I fear it may actually be DNS related. If I watch Live Headers in Firefox, absolutely nothing happens during this 'hanging' period. After that, the responses come back fairly promptly. UPDATE (05/04): I built the latest versions of Apache and PHP from source, no luck. I then removed those and used the remi repo to update all my packages to the latest stable. Segfaults seem to have stopped, but the hanging is continuing. ini's are at; www.skylinesaustralia.com/php.ini www.skylinesaustralia.com/my.cnf www.skylinesaustralia.com/httpd.conf UPDATE - SOLVED! - The issue was having a gigantic query cache size in MySQL. It was 2GB, changing it to 64M sorted it. Thanks for all the help everybody, much appreciated!!

  Read the article

• Looking for a NTP Server Software for Windows

  - by Simon

  I'm looking for a, preferably free, NTP Server for Windows Server 2003/2008. We have already tried the built in Windows Time Server, but our tests did show that it is not very accurate, we see time differences up to 500ms. The max time difference we can allow for our application is ~100ms. Now we have already used the Meinberg NTPd for Windows. It works great except we have one big issue with it: If there is a network connection problem between the client and server, the ntp server is in a panic state It won't give the client a new time until we restart the ntp service. This is a big issue which has caused us some trouble. It was working fine for months until there was a network problem we didn't notice, we only noticed it after a week when the time difference was already 30 sec. on the clients. So please suggest some alternative NTP Server for windows. I did Google but I get a lot of unrelated search results. Edit: So far the ntpd windows version was very accurate and I'd like to stick with it. The only problem is the "panic state" after a network disconnect. Maybe some knows here what the cause of this is and how to fix it. Also, I forgot to mention that we have a server/client setup like this: Server1 -- Server2 -- Server3 -- Client1 -- Client2 -- Client3 So Server2 gets its time from Server1, Server3 gets its time from Server2, and the Clients get their time from Server3. Also, there are clients connected directly to Server2. It is important that all Servers and Clients have the exact same time (within ~100ms) Now there was a network problem with Server3 and its clients. The servers run the ntpd port for Windows, which acts as NTP server and client. The clients have Dimension4 as NTP client. After the network problem, the error message in D4 was something like this (out the top of my head, don't have the exact error message): Server response: The server is in a panic state (could not sync clock) I read through the ntpd docs, and the only mention of "panic" is when the time difference is 10000 seconds which will cause to exit the ntpd server but this was not the case. Also there is a "-g" command line switch to disable the panic exit, but it is already set by default. Any ideas what could cause the panic state and how to get rid of it next time?

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David Boike

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• how does openvpn decide which interface to get IP addrs from

  - by bkrupa

  Using ubuntu 10.04 on both ends. We have a client and server machine on the SAME network attempting to make a vpn connection. We use the config files from here and made minimal changes. The server and client start and seem to connect without any trouble. The server looks like: Wed Feb 23 22:13:22 2011 MULTI: multi_create_instance called Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Re-using SSL/TLS context Wed Feb 23 22:13:22 2011 192.168.1.55:47166 LZO compression initialized Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel MTU parms [ L:1574 D:138 EF:38 EB:0 ET:0 EL:0 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Local Options hash (VER=V4): 'f7df56b8' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Expected Remote Options hash (VER=V4): 'd79ca330' Wed Feb 23 22:13:22 2011 192.168.1.55:47166 TLS: Initial packet from 192.168.1.55:47166, sid=69112e42 5458135b *...* Wed Feb 23 22:13:22 2011 192.168.1.55:47166 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Feb 23 22:13:22 2011 192.168.1.55:47166 [client1] Peer Connection Initiated with 192.168.1.55:47166 On the client side the connection looks like: Wed Feb 23 22:20:07 2011 [server] Peer Connection Initiated with [AF_INET]192.168.1.41:1194 Wed Feb 23 22:20:10 2011 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Wed Feb 23 22:20:10 2011 PUSH: Received control message: 'PUSH_REPLY,route-gateway 10.8.0.4,ping 10,ping-restart 120,ifconfig 10.8.0.50 255.255.255.0' ... Wed Feb 23 22:20:10 2011 /sbin/ifconfig tap0 10.8.0.50 netmask 255.255.255.0 mtu 1500 broadcast 10.8.0.255 Wed Feb 23 22:20:10 2011 Initialization Sequence Completed The openvpn server has been configured to assign ip addresses in the range 10.8.0.* and the client has been given 10.8.0.50. When I run the following nmap from the client: Starting Nmap 5.00 ( http://nmap.org ) at 2011-02-23 22:04 EST Host 10.8.0.50 is up (0.00047s latency). Nmap done: 256 IP addresses (1 host up) scanned in 30.34 seconds Host 192.168.1.1 is up (0.0025s latency). Host 192.168.1.18 is up (0.074s latency). Host 192.168.1.41 is up (0.0024s latency). Host 192.168.1.55 is up (0.00018s latency). Nmap done: 256 IP addresses (4 hosts up) scanned in 6.33 seconds If I run an nmap from the server on 10.8.0.* I get nothing. If the client has two interfaces (wireless and tap device) when you look for a certain ip address, how does it decide which interface to connect on?

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• Finding underlying cause of Window 7 Account corruption.

  - by Carl Jokl

  I have been having trouble with my Sister's computer which I built. It is running Windows 7 Ultimate x64. The problem is that I have had problems with the accounts becoming corrupted. First problems manifest themselves in the form of Windows saying the profile failed to be loaded properly and a temporary profile. Eventually the account will not allow login at all. An error message along the lines the authentication service failing the login. I have found information about this problem and how to fix it. The problem being that something has corrupted the account profile and backing up and recreating the accounts fixes the problem. I have been able to fix things and get logins working again but over the period of usually about a week it happens again. Bit by bit the accounts corrupt and then it is back to square one. I am frustrated because I don't know what the underlying cause of the problem is i.e. what is causing the accounts to be corrupted in the first place. At the moment I am just treating the symptoms. I was hoping someone who may have more experience with dealing with this problem might be able to help me find the root cause. Some articles suggest that Norton Internet Security is a big culprit of this problem which is installed. I could try uninstalling Norton and see if it helps. The one thing which is different about this computer to any other I have built is that it has a solid state drive. Actually it has both a hard drive and solid state drive. The documents and settings i.e. the Users directory is stored on the hard drive. This was done following an article about moving the user account data onto a separate drive on Windows 7 which I found on the Internet. Moving the User accounts is more of a pain under Windows 7 and this solution involved creating a low level file system link to the folder from the boot drive (Solid State) to the Hard Drive. The idea is that the computer behaves just as if it is accessing the User's folder from the boot drive but actually the data is stored on the hard drive. This may have nothing to do with the cause of the problem but due to the problem being user account corruption it is a possibility I have not been able to rule out. Any help would be appreciated as I would be glad to see the back of this problem.

  Read the article

• flashcache with mdadm and LVM

  - by Backtogeek

  I am having trouble setting up flashcache on a system with LVM and mdadm, I suspect I am either just missing an obvious step or getting some mapping wrong and hoped someone could point me in the right direction? system info: CentOS 6.4 64 bit mdadm config md0 : active raid1 sdd3[2] sde3[3] sdf3[4] sdg3[5] sdh3[1] sda3[0] 204736 blocks super 1.0 [6/6] [UUUUUU] md2 : active raid6 sdd5[2] sde5[3] sdf5[4] sdg5[5] sdh5[1] sda5[0] 3794905088 blocks super 1.1 level 6, 512k chunk, algorithm 2 [6/6] [UUUUUU] md3 : active raid0 sdc1[1] sdb1[0] 250065920 blocks super 1.1 512k chunks md1 : active raid10 sdh1[1] sda1[0] sdd1[2] sdf1[4] sdg1[5] sde1[3] 76749312 blocks super 1.1 512K chunks 2 near-copies [6/6] [UUUUUU] pcsvan PV /dev/mapper/ssdcache VG Xenvol lvm2 [3.53 TiB / 3.53 TiB free] Total: 1 [3.53 TiB] / in use: 1 [3.53 TiB] / in no VG: 0 [0 ] flashcache create command used: flashcache_create -p back ssdcache /dev/md3 /dev/md2 pvdisplay --- Physical volume --- PV Name /dev/mapper/ssdcache VG Name Xenvol PV Size 3.53 TiB / not usable 106.00 MiB Allocatable yes PE Size 128.00 MiB Total PE 28952 Free PE 28912 Allocated PE 40 PV UUID w0ENVR-EjvO-gAZ8-TQA1-5wYu-ISOk-pJv7LV vgdisplay --- Volume group --- VG Name Xenvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 2 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 3.53 TiB PE Size 128.00 MiB Total PE 28952 Alloc PE / Size 40 / 5.00 GiB Free PE / Size 28912 / 3.53 TiB VG UUID 7vfKWh-ENPb-P8dV-jVlb-kP0o-1dDd-N8zzYj So that is where I am at, I thought that was the job done however when creating a logical volume called test and mounting it is /mnt/test the sequential write is pathetic, 60 ish MB/s /dev/md3 has 2 x SSD's in Raid0 which alone is performing at around 800 MB/s sequential write and I am trying to cache /dev/md2 which is 6 x 1TB drives in raid6 I have read a number of pages through the day and some of them here, it is obvious from the results that the cache is not functioning but I am unsure why. I have added the filter line in the lvm.conf filter = [ "r|/dev/sdb|", "r|/dev/sdc|", "r|/dev/md3|" ] It is probably something silly but the cache is clearly performing no writes so I suspect I am not mapping it or have not mounted the cache correctly. dmsetup status ssdcache: 0 7589810176 flashcache stats: reads(142), writes(0) read hits(133), read hit percent(93) write hits(0) write hit percent(0) dirty write hits(0) dirty write hit percent(0) replacement(0), write replacement(0) write invalidates(0), read invalidates(0) pending enqueues(0), pending inval(0) metadata dirties(0), metadata cleans(0) metadata batch(0) metadata ssd writes(0) cleanings(0) fallow cleanings(0) no room(0) front merge(0) back merge(0) force_clean_block(0) disk reads(9), disk writes(0) ssd reads(133) ssd writes(9) uncached reads(0), uncached writes(0), uncached IO requeue(0) disk read errors(0), disk write errors(0) ssd read errors(0) ssd write errors(0) uncached sequential reads(0), uncached sequential writes(0) pid_adds(0), pid_dels(0), pid_drops(0) pid_expiry(0) lru hot blocks(31136000), lru warm blocks(31136000) lru promotions(0), lru demotions(0) Xenvol-test: 0 10485760 linear I have included as much info as I can think of, look forward to any replies.

  Read the article

• Apache Alias subfolder and starting with dot

  - by MauricioOtta

  I have a multi purpose server running ArchLinux that currently serves multiple virtual hosts from /var/www/domains/EXAMPLE.COM/html /var/www/domains/EXAMPLE2.COM/html I deploy those websites (mostly using Kohana framework) using a Jenkins job by checking out the project, removes the .git folder and ssh-copy the tar.gz to /var/www/domains/ on the server and untars it. Since I don't want to have to re-install phpMyAdmin after each deploy, I decided to use an alias. I would like the alias to be something like /.tools/phpMyAdmin/ so I could have more "tools" later if I wanted to. I have tried just changing the default httpd-phpmyadmin.conf that was installed by following the official WIKI: https://wiki.archlinux.org/index.php/Phpmyadmin Alias /.tools/phpMyAdmin/ "/usr/share/webapps/phpMyAdmin" <Directory "/usr/share/webapps/phpMyAdmin"> AllowOverride All Options FollowSymlinks Order allow,deny Allow from all php_admin_value open_basedir "/var/www/:/tmp/:/usr/share/webapps/:/etc/webapps:/usr/share/pear/" </Directory> Changing only that, doesn't seem to work with my current setup on the server, and apache forwards the request to the framework which 404s (as there's no route to handle /.tools/phpAdmin). I have Mass Virtual hosting enable and setup like this: # # Use name-based virtual hosting. # NameVirtualHost *:8000 # get the server name from the Host: header UseCanonicalName On # splittable logs LogFormat "%{Host}i %h %l %u %t \"%r\" %s %b" vcommon CustomLog logs/access_log vcommon <Directory /var/www/domains> # ExecCGI is needed here because we can't force # CGI execution in the way that ScriptAlias does Options FollowSymLinks ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> RewriteEngine On # a ServerName derived from a Host: header may be any case at all RewriteMap lowercase int:tolower ## deal with normal documents first: # allow Alias /icons/ to work - repeat for other aliases RewriteCond %{REQUEST_URI} !^/icons/ # allow CGIs to work RewriteCond %{REQUEST_URI} !^/cgi-bin/ # do the magic RewriteCond %{SERVER_NAME} ^(www\.|)(.*) RewriteRule ^/(.*)$ /var/www/domains/${lowercase:%2}/html/$1 ## and now deal with CGIs - we have to force a MIME type RewriteCond %{REQUEST_URI} ^/cgi-bin/ RewriteRule ^/(.*)$ /var/www/domains/${lowercase:%{SERVER_NAME}}/cgi-bin/$1 [T=application/x-httpd-cgi] There is also nginx running on this server on port 80 as a reverse proxy for Apache: location ~ \.php$ { proxy_pass http://127.0.0.1:8000; } Everything else was setup by following the official WIKI so I don't think those would cause trouble. Do I need to have the alias for phpMyAdmin setup along the mass virtual hosting or can it be in a separate include file for that alias to work?

  Read the article

• How to get physical partition name from iSCSI details on Windows?

  - by Barry Kelly

  I've got a piece of software that needs the name of a partition in \Device\Harddisk2\Partition1 style, as shown e.g. in WinObj. I want to get this partition name from details of the iSCSI connection that underlies the partition. The trouble is that disk order is not fixed - depending on what devices are connected and initialized in what order, it can move around. So suppose I have the portal name (DNS of the iSCSI target), target IQN, etc. I'd like to somehow discover which volumes in the system relate to it, in an automated fashion. I can write some PowerShell WMI queries that get somewhat close to the desired info: PS> get-wmiobject -class Win32_DiskPartition NumberOfBlocks : 204800 BootPartition : True Name : Disk #0, Partition #0 PrimaryPartition : True Size : 104857600 Index : 0 ... From the Name here, I think I can fabricate the corresponding name by adding 1 to the partition number: \Device\Harddisk0\Partition1 - Partition0 appears to be a fake partition mapping to the whole disk. But the above doesn't have enough information to map to the underlying physical device, unless I take a guess based on exact size matching. I can get some info on SCSI devices, but it's not helpful in joining things up (iSCSI target is Nexenta/Solaris COMSTAR): PS> get-wmiobject -class Win32_SCSIControllerDevice __GENUS : 2 __CLASS : Win32_SCSIControllerDevice ... Antecedent : \\COBRA\root\cimv2:Win32_SCSIController.DeviceID="ROOT\\ISCSIPRT\\0000" Dependent : \\COBRA\root\cimv2:Win32_PnPEntity.DeviceID="SCSI\\DISK&VEN_NEXENTA&PROD_COMSTAR... Similarly, I can run queries like these: PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_TargetClass PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_PersistentDevices These guys return information relating to my iSCSI target name and the GUID volume name respectively (a volume name like \\?\Volume{guid-goes-here}), but the GUID volume name is no good to me, and there doesn't appear to be a reliable correspondence between the target name and the volume that I can join on. I simply can't find an easy way of getting from an IQN (e.g. iqn.1992-01.com.example:storage:diskarrays-sn-a8675309) to physical partitions mapped from that target. The way I do it by hand? I start Disk Management, and look for a partition of the correct size, verify that its driver says NEXENTA COMSTAR, and look at the disk number. But even this is unreliable if I have multiple iSCSI volumes of the exact same size. Any suggestions?

  Read the article

• Google Apps For Business, SSO, AD FS 2.0 and AD

  - by Dominique dutra

  We are a small company with 22 people in the office. We had a lot of problems with e-mail in the past so I decided to change over to Google Apps for Business. It is the perfect solution for us, except for one thing: I need to be able to control the access to the mailboxes. Only users inside the office, authenticated to AD, or users authenticated to our VPN can connect to gmail. From what I've read it is possible using the SSO (Single Sign On) solution provided by Google - but i am having some trouble finding consistent information about it. First of all, our infrastructure: Windows Server 2008 R2 Active Directory, one domain only. Kerio Control for QoS and VPN. That's about it on our side. On Google Apps' side, I have one account, and 03 domains that my users use to log in. The main domain has most of the users, but the are a couple of people that login using one of the subdomains. I have a 03 domains because I run mail for 03 companies and wanted all to be in within the same control panel. Well, I found some guides on the internet but none of them cover the AD FS installation part. I've read somewhere that I needed to download AD FS 2.0 directly from Microsoft.com, because the one that came with Windows Server was a old version. I downloaded it (adfsSetup.exe) and tried to install but got an error, saying that I needed a Windows Server 2008 Sp2 for that program. My Windows Server 2008 is R2. I really need some help here, this is very importand, I dont want to have to pay $1000 for a SSO solution when i have an AD set up. Can someone please point me out to the right direction? Where can I find an AD FS 2.0 setup compatible with R2 would be a good start, or the one that came with r2 is already the 2.0 version. After the initial setup, there are some guides on the internet about the Google Apps part. It seems to be really easy. I also tried adding AD FS role, but there are a bunch of options wich I have no idea what means, and I coudn't find any guide covering that on the internet. I dont have a lot of experience with Windows Server, but I have a company wich is certificated and provide us with support. I can ask for their help in the later setup, but I dont think ADFS is a very common thing to deal with.

  Read the article

• Webserver Responses Hanging

  - by drscroogemcduck

  From some networks requesting certain images on our webserver is very flakey. I've looked at tcpdumps on both sides and the server sends back part of the file and the client ACKs the TCP packet but the server never receives the ACK. The servers view: 41 19.941136 212.169.34.114 209.20.73.85 TCP 52456 > http [SYN] Seq=0 Win=8192 Len=0 MSS=1460 WS=2 42 19.941136 209.20.73.85 212.169.34.114 TCP http > 52456 [SYN, ACK] Seq=0 Ack=1 Win=5440 Len=0 MSS=1360 46 20.041142 212.169.34.114 209.20.73.85 TCP 52456 > http [ACK] Seq=1 Ack=1 Win=65280 Len=0 47 20.045142 212.169.34.114 209.20.73.85 HTTP GET /map/map/s+74-WBkWk0aR28Yy-YjXA== HTTP/1.1 48 20.045142 209.20.73.85 212.169.34.114 TCP http > 52456 [ACK] Seq=1 Ack=522 Win=6432 Len=0 49 20.045142 209.20.73.85 212.169.34.114 TCP [TCP segment of a reassembled PDU] (Part of the content of the image 2720 bytes. i assume it is reassembled in tcpdump and it is fragmented over the wire.) ** never receives the ACK sent in frame 282 and will eventually resend the tcp segment ** The clients view: 274 26.161773 10.0.16.67 209.20.73.85 TCP 52456 > http [SYN] Seq=0 Win=8192 Len=0 MSS=1460 WS=2 276 26.262867 209.20.73.85 10.0.16.67 TCP http > 52456 [SYN, ACK] Seq=0 Ack=1 Win=5440 Len=0 MSS=1360 277 26.263255 10.0.16.67 209.20.73.85 TCP 52456 > http [ACK] Seq=1 Ack=1 Win=65280 Len=0 278 26.265193 10.0.16.67 209.20.73.85 HTTP GET /map/map/s+74-WBkWk0aR28Yy-YjXA== HTTP/1.1 279 26.365562 209.20.73.85 10.0.16.67 TCP http > 52456 [ACK] Seq=1 Ack=522 Win=6432 Len=0 280 26.368002 209.20.73.85 10.0.16.67 TCP [TCP segment of a reassembled PDU] (Part of the content of the image. Only 1400 bytes.) 282 26.571380 10.0.16.67 209.20.73.85 TCP 52456 > http [ACK] Seq=522 Ack=1361 Win=65280 Len=0 The network we are having trouble with is NATd. Is there any kind of explanation for this weirdness?

  Read the article

• Asus M4A79XTD-EVO / AMD Phenom II X4 965 Crashes / BSOD / Hangs / Restarts

  - by Tiby

  I'll try to be as concise as possible because I have a lot to say about my problem, but I'd rather say it when asked or when I feel it's necessary, just to make this initial reading clearer. For about a year and a half I have periods when my system has all the problems in the title (I'll use the word 'crash' for either one). I'll list some patterns and what I tried to do and what were the results, but the list is not exclusive: usually it crashes when a CPU-intensive operation is in progress, like a game or video encoding or HD movie rendering, but also sometimes crashes when I'm doing nothing after a first crash the system is very unstable and sometimes it crashes even during POST, or doesn't boot at all Some months ago I went to a local service (one that you just put your computer on the table and sit there with a guy and trying to figure out the problem, very rare these days) and they used OCCT and it crashed every time he changed some part to test it out (PSU, RAM, video card, HDD). The last one was the CPU. They changed the CPU and it didn't crash any more. Then when they put my CPU back, it also didn't crash. We figured that the trouble was the thermal paste (probably some 2 years old) because it was the only thing changed while testing. Up until 2 weeks ago, I haven't had any more problems. 2 weeks ago the problems reappeared. I changed again the thermal paste, put some Arctic Silver 5, and for about a week everything worked perfect (tried some games, video encoding, no more crashes). But again it started crashing in the same fashion as the first time. But now, instead, I figured out a very odd behaviour: when I start some of the apps above, in most cases it crashes if I start OCCT and turn on the CPU test, and run any of the programs above, it doesn't crash, even if the CPU is on 100% load (and 65-70 degrees Celsius temperature) if I shut down OCCT and continue using the programs, it crashes in a very short period of time (even if the CPU is on 5-10% load and 40 degrees) There are so many patterns and temporary solutions that I figured out in this year and a half period of time, that I can't include them all because I don't know which one are more relevant, but I'll happily provide any details you ask. My system is: CPU: AMD Phenom II X4 965 (3400 MHz - 125W) MB: ASUS M4A79XTD - EVO RAM: Corsair Vengeance 8 GB (2 x 4GB) CL8 1600MHz Video: HIS Radeon HD5770 1GB PSU: Corsair 750W HDD: Western Digital 1TB OS: Win 7 Enterprise 64 BIT (also tried with Windows Server 2008 R2 Trial and Win XP)

  Read the article

• Win-XP Browsers Hang on page load - (waiting for...)

  - by CHarmon

  Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Default permission for newly-created files/folders using ACLs not respected by commands like "unzip"

  - by Ngoc Pham

  I am having trouble with setting up a system for multiple users accessing the same set of files. I've read tuts and docs around and played with ACLs but haven't succeeded yet. MY SCENARIO: Have multiple users, for example, user1 and user2, which is belong to a group called sharedusers. They must have all WRITE permission to a same set of files and directories, say underlying in /userdata/sharing/. I have the folder's group set to sharedusers and SGID to have all newly created files/dirs inside set to same group. ubuntu@home:/userdata$ ll drwxr-sr-x 2 ubuntu sharedusers 4096 Nov 24 03:51 sharing/ I set ACLs for this directory so I can have permission of sub dirs/files inheritted from its parents. ubuntu@home:/userdata$ setfacl -m group:sharedusers:rwx sharing/ ubuntu@home:/userdata$ setfacl -d -m group:sharedusers:rwx sharing/ Here's what I've got: ubuntu@home:/userdata$ getfacl sharing/ # file: sharing/ # owner: ubuntu # group: sharedusers # flags: -s- user::rwx group::r-x group:sharedusers:rwx mask::rwx other::r-x default:user::rwx default:group::r-x default:group:sharedusers:rwx default:mask::rwx default:other::r-x Seems okay as when I create new folder with new files inside and the permission is correct. ubuntu@home:/userdata/sharing$ mkdir a && cd a ubuntu@home:/userdata/sharing/a$ touch a_test ubuntu@home:/userdata/sharing/a$ getfacl a_test # file: a_test # owner: ubuntu # group: sharedusers user::rw- group::r-x #effective:r-- group:sharedusers:rwx #effective:rw- mask::rw- other::r-- As you can see, the sharedusers group has effective permission rw-. HOWEVER, if I have a zip file, and use unzip -q command to unzip the file inside the folder sharing, the extracted folders don't have group write permisison. Therefore, the users from group sharedusers cannot modify files under those extracted folders. ubuntu@home:/userdata/sharing$ unzip -q Joomla_3.0.2-Stable-Full_Package.zip ubuntu@home:/userdata/sharing$ ll drwxrwsr-x+ 2 ubuntu sharedusers 4096 Nov 24 04:00 a/ drwxr-xr-x+ 10 ubuntu sharedusers 4096 Nov 7 01:52 administrator/ drwxr-xr-x+ 13 ubuntu sharedusers 4096 Nov 7 01:52 components/ You an spot the difference in permissions between folder a (created before) and folder administrator extracted by unzip. And the ACLs of a files inside administrator: ubuntu@home:/userdata/sharing$ getfacl administrator/index.php # file: administrator/index.php # owner: ubuntu # group: ubuntu user::rw- group::r-x #effective:r-- group:sharedusers:rwx #effective:r-- mask::r-- other::r-- It also has ubuntu group, not sharedusers group as expected. Could someone please explain the problem and give me advice? Thank you in advance!

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• Puppet and launchd services?

  - by Joel Westberg

  We have a production environment configured with Puppet, and want to be able to set up a similar environment on our development machines: a mix of Red Hats, Ubuntus and OSX. As might be expected, OSX is the odd man out here, and sadly, I'm having a lot of trouble with getting this to work. My first attempt was using macports, using the following declaration: package { 'rabbitmq-server': ensure => installed, provider => macports, } but this, sadly, generates the following error: Error: /Stage[main]/Rabbitmq/Package[rabbitmq-server]: Could not evaluate: Execution of '/opt/local/bin/port -q installed rabbitmq-server' returned 1: usage: cut -b list [-n] [file ...] cut -c list [file ...] cut -f list [-s] [-d delim] [file ...] while executing "exec dscl -q . -read /Users/$env(SUDO_USER) NFSHomeDirectory | cut -d ' ' -f 2" (procedure "mportinit" line 95) invoked from within "mportinit ui_options global_options global_variations" Next up, I figured I'd give homebrew a try. There is no package provider available by default, but puppet-homebrew seemed promising. Here, I got much farther, and actually managed to get the install to work. package { 'rabbitmq': ensure => installed, provider => brew, } file { "plist": path => "/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist", source => "/usr/local/opt/rabbitmq/homebrew.mxcl.rabbitmq.plist", ensure => present, owner => root, group => wheel, mode => 0644, } service { "homebrew.mxcl.rabbitmq": enable => true, ensure => running, provider => "launchd", require => [ File["/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist"] ], } Here, I don't get any error. But RabbitMQ doesn't start either (as it does if I do a manual load with launchctl) [... snip ...] Debug: Executing '/bin/launchctl list' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /var/db/launchd.db/com.apple.launchd/overrides.plist' Debug: /Schedule[weekly]: Skipping device resources because running on a host Debug: /Schedule[puppet]: Skipping device resources because running on a host Debug: Finishing transaction 2248294820 Debug: Storing state Debug: Stored state in 0.01 seconds Finished catalog run in 25.90 seconds What am I doing wrong?

  Read the article

< Previous Page | 425 426 427 428 429 430 431 432 433 434 435 436  | Next Page >