Search Results

Search found 18395 results on 736 pages for 'admin interface'.

Page 43/736 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

  • Vyatta masquerade out bridge interface

    - by miquella
    We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

    Read the article

  • Separated virtual networks with same subnet range with 2 interface

    - by Coolpet
    I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

    Read the article

  • gitosis-admin git push failed, exec hooks/post-update

    - by v14nt0
    I'm following this tutorial http://scie.nti.st/2007/11/14/hosting-git-repositories-the-easy-and-secure-way after this step git commit -a -m "Allow jdoe write access to free_monkey" git push i always failed, with this error fatal: exec hooks/post-update failed. this is from my /home/git/repositories/gitosis-admin/hooks/post-update -rwxr-xr-x 1 git git 83 Mar 10 11:49 post-update so i change gitosis.conf manually from server for adding new repositories, and repos can work fine. i've google what might cause it, i want to admin gitosis in proper way Please Help Regards, REV

    Read the article

  • CakePHP admin panel

    - by ab
    I am new to CakePHP and want an admin panel on my custom CMS for a client. Is there any way other than just linking to an admin page to each controller that I can pull views from other controllers such as users and posts?

    Read the article

  • Replicating multicolumn lists from the Django admin CSS

    - by mfalcon
    Hi, I'm developing a Django project and I've to show a multicolumn list for the different objects of a table. I like the design of the django-admin for showing list-objects so I looked at the code to see how it works. As I am a CSS begginer the code seemed a bit difficult and extensive to comprehend. Is there a simplier way to make what I want or actually the CSS code of the django-admin is the path to follow?

    Read the article

  • Django admin fails when using includes in urlpatterns

    - by zenWeasel
    I am trying to refactor out my application a little bit to keep it from getting too unwieldily. So I started to move some of the urlpatterns out to sub files as the documentation proposes. Besides that fact that it just doesn't seem to be working (the items are not being rerouted) but when I go to the admin, it says that 'urlpatterns has not been defined'. The urls.py I have at the root of my application is: if settings.ENABLE_SSL: urlpatterns = patterns('', (r'^checkout/orderform/onepage/(\w*)/$','checkout.views.one_page_orderform',{'SSL':True},'commerce.checkout.views.single_product_orderform'), ) else: urlpatterns = patterns('', (r'^checkout/orderform/onepage/(\w*)/$','commerce.checkout.views.single_product_orderform'), ) urlpatterns+= patterns('', (r'^$', 'alchemysites.views.route_to_home'), (r'^%s/' % settings.DAJAXICE_MEDIA_PREFIX, include('dajaxice.urls')), (r'^/checkout/', include('commerce.urls')), (r'^/offers',include('commerce.urls')), (r'^/order/',include('commerce.urls')), (r'^admin/', include(admin.site.urls)), (r'^accounts/login/$', login), (r'^accounts/logout/$', logout), (r'^(?P<path>.*)/$','alchemysites.views.get_path'), (r'^static/(?P<path>.*)$', 'django.views.static.serve', {'document_root':settings.MEDIA_ROOT}), The urls I have moved out so far are the checkout/offers/order which are all subapps of 'commerce' where the urls.py for the apps are so to be clear. /urls.py in questions (included here) /commerce/urls.py where the urls.py I want to include is: order_info = { 'queryset': Order.objects.all(), } urlpatterns+= patterns('', (r'^offers/$','offers.views.start_offers'), (r'^offers/([a-zA-Z0-9-]*)/order/(\d*)/add/([a-zA-Z0-9-]*)/(\w*)/next/([a-zA-Z0-9-)/$','offers.views.show_offer'), (r'^reports/orders/$', list_detail.object_list,order_info), ) and the applications offers lies under commerce. And so the additional problem is that admin will not work at all, so I'm thinking because I killed it somewhere with my includes. Things I have checked for: Is the urlpatterns variable accidentally getting reset somewhere (i.e. urlpatterns = patterns, instead of urlpatterns+= patterns) Are the patterns in commerce.urls valid (yes, when moved back to root they work). So from there I am stumped. I can move everything back into the root, but was trying to get a little decoupled, not just for theoretical reason but for some short terms ones. Lastly if I enter www.domainname/checkout/orderform/onepage/xxxjsd I get the correct page. However, entering www.domainname/checkout/ gets handled by the alchemysites.views.get_path. If not the answer (because this is pretty darn specific), then is there a good way for troubleshoot urls.py? It seems to just be trial and error. Seems there should be some sort of parser that will tell you what your urlpatterns will do.

    Read the article

  • Missing trailing / for admin page edits in django-cms

    - by 47
    I've managed to set up Django CMS for my website successfully...however, when editing a page in the admin, the trailing / isn't added automatically so my URL's look something like: http://localhost:8000/admin/cms/page/22 When I tried running the example project that comes bundled with the Django-CMS setup, this slash is added automatically....how can I have the same for my project?

    Read the article

  • web applications tend to have a admin panel?

    - by ajsie
    i wonder if large web applications like twitter and facebook have admin panels to handle CRUD for users, posts, images, themes and so on just like in CMS like drupal? so programmers have to code the front for the regular users AND back for the administrators? if i develop an web application is it recommended that i also code the admin part? or is it unnecessary since i can handle all directly in mysql and by editing php scripts directly? share your thoughts! thanks

    Read the article

  • Magneto admin separate ajax product Grid load

    - by Ela
    Hi, I have to load separate product Grid to select needed product items and store it under my another custom module's model in magento admin side. So i have a custom module created by using Module creator and added another tab which i wish to show all the products as a list or grid to select(Exactly i want it like in new order page under admin side) and store. Do you anybody know how to load product grid or list under custom module area. I really appreciate your help. Thanks

    Read the article

  • no DOM in wordpress admin

    - by Chris
    I correctly inserted a javascript file into the wordPress admin with : wp_enqueue_script() I know that the script is loading. I tested it with an alert(). I then found that I am unable to access the DOM. When I tried : document.getElementsByTagName('body')[0].addEventListener('load', function() {}); This error was: Uncaught TypeError: Cannot call method 'addEventListener' of undefined This is the first time I have used 'settings api' or inserted scripts into the WordPress admin.

    Read the article

  • CMS Module in Magento admin

    - by user346475
    I want create a new module just like a CMS page in which display multiple Items and admin will be manage it according own requirement could u please tell me how i integrate this module in admin Thanks in advance Pardeep Singal

    Read the article

  • CUPS basic auth error through web interface

    - by Inaimathi
    I'm trying to configure CUPS to allow remote administration through the web interface. There's enough documentation out there that I can figure out what to change in my cupsd.conf (changing Listen localhost:631 to Port 631, and adding Allow @LOCAL to the /, /admin and /admin/conf sections). I'm now at the point where I can see the CUPS interface from another machine on the same network. The trouble is, when I try to Add Printer, I'm asked for a username and password, but my response is rejected even when I know I've gotten it right (I assume it's asking for the username and password of someone in the lpadmin group on the server machine; I've sshed in with credentials its rejecting, and the user I'm using has been added to the lpadmin group). If I disable auth outright, by changing DefaultAuthType Basic to DefaultAuthType None, I get an "Unauthorized" error instead of a password request when I try to Add Printer. What am I doing wrong? Is there a way of letting users from the local network to administer the print server through the CUPS web interface? EDIT: By request, my complete cupsd.conf (spoiler: minimally edited default config file that comes with the edition of CUPS from the Debian wheezy repos): LogLevel warn MaxLogSize 0 SystemGroup lpadmin Port 631 # Listen localhost:631 Listen /var/run/cups/cups.sock Browsing On BrowseOrder allow,deny BrowseAllow all BrowseLocalProtocols CUPS dnssd # DefaultAuthType Basic DefaultAuthType None WebInterface Yes <Location /> Order allow,deny Allow @LOCAL </Location> <Location /admin> Order allow,deny Allow @LOCAL </Location> <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny Allow @LOCAL </Location> # Set the default printer/job policies... <Policy default> # Job/subscription privacy... JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default # Job-related operations must be done by the owner or an administrator... <Limit Create-Job Print-Job Print-URI Validate-Job> Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default CUPS-Get-Devices> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> # Set the authenticated printer/job policies... <Policy authenticated> # Job/subscription privacy... JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default # Job-related operations must be done by the owner or an administrator... <Limit Create-Job Print-Job Print-URI Validate-Job> AuthType Default Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy>

    Read the article

  • Windows Server 2008 R2 Server Core with AD Role having GUI Admin Console

    - by Robert Koritnik
    I would like to setup a machine with Windows Server 2008 R2 Server Core and install following server roles: Active Directory Domain Services Active Directory Federation Services Active Directory Lightweight Directory Services (I'm not sure whether I actually need this one - see note below) I'm obviously going to install Enterprise Edition. Question Can I have an AD administration graphical user interface to manage Active Directory on Server Core machine? I would really like to have it, because I'm not so keen to do stuff using power-shell, because I've never managed AD as well, so a GUI would be much more helpful, because I could at least visualize it a bit better and maybe understand AD structures. Note: I'm setting up development environment machine as well and installing Sharepoint Foundation 2010 on in so it would use this AD machine.

    Read the article

  • Deny users in a certain group access to dovecot

    - by celil
    I installed the dovecot-imapd package in Ubuntu, and my setup is as follows: $ sudo dovecot -n # 1.2.9: /etc/dovecot/dovecot.conf # OS: Linux 2.6.32-27-generic-pae i686 Ubuntu 10.04.1 LTS log_timestamp: %Y-%m-%d %H:%M:%S protocols: imaps login_dir: /var/run/dovecot/login login_executable: /usr/lib/dovecot/imap-login mail_privileged_group: mail mail_location: maildir:~/Maildir mbox_write_locks: fcntl dotlock auth default: passdb: driver: pam userdb: driver: passwd For security reasons I would like to deny all users that are in the admin group ability to do imap login via dovecot. This is done in order to prevent a brute force attacker from discovering the admin passwords, and obtaining administrator privileges on the system. How can this be achieved? Presumably, I will have to modify some settings in /etc/dovecot/dovecot.conf, but I am hesitant to change the default settings lest I create other security vulnerabilities.

    Read the article

  • Behaviour of disabling "Allow non-administrators to receive notifications" GPO

    - by Jaymz
    Hi everyone, As the title suggests, I'm trying to figure out the specific behaviour of the following GPO when disabled: Administrative Templates Windows Components Allow non-administrators to receive update notifications We've just started using WSUS, and have added a few machines for testing. At the moment, this is set to Enabled. The problem with this setting is it seems to allow users to opt out of certain updates if they deselect the checkbox after hitting custom install. My main concern with disabling this setting is this: Does it stop non-admins from getting the installs deployed to them? My guess would be that it will just install them silently at the set scheduled time, suppressing any prompts and ensuring they don't get the opportunity to cancel them (this is what I want). My worry is that non-admin users will never get updates pushed to them unless an admin goes and logs on to their machine (not what I want, and seems like a silly situation to be in). Thanks in advance, Jaymz.

    Read the article

  • Ruby on Rails: Routing error

    - by JamesMcL13
    I am having trouble deleting and showing user records. Here is my routes.rb FinalApp::Application.routes.draw do resources :admin devise_for :users, :controllers => { :registrations => 'admin' } resources :projects match "search" => "projects#search", :as => :search root :to => 'projects#index' end Here is my admin controller: class AdminController < ApplicationController def index @users = User.all respond_to do |format| format.html # index.html.erb format.json { render :json => @users } end end def create @user = User.new(params[:user]) respond_to do |format| if @user.save format.html { redirect_to @user, notice: 'User was successfully created.' } format.json { render json: @user, status: :created, location: @user } else format.html { render action: "new" } format.json { render json: @user.errors, status: :unprocessable_entity } end end end # GET /users/1 # GET /users/1.json def show @user = User.find(params[:id]) @user_user_id = params[:id] respond_to do |format| format.html # show.html.erb format.json { render json: @user } end end # GET /users/new # GET /users/new.json def new @user = User.new respond_to do |format| format.html # new.html.erb format.json { render json: @user } end end # GET /users/1/edit def edit @user = User.find(params[:id]) end # POST /users # POST /users.json # PUT /users/1 # PUT /users/1.json def update @user = User.find(params[:id]) respond_to do |format| if @user.update_attributes(params[:user]) format.html { redirect_to @user, notice: 'User was successfully updated.' } format.json { head :no_content } else format.html { render action: "edit" } format.json { render json: @user.errors, status: :unprocessable_entity } end end end # DELETE /users/1 # DELETE /users/1.json def destroy @user = User.find(params[:id]) @user.destroy respond_to do |format| format.html { redirect_to users_url } format.json { head :no_content } end end end Here is my view: <%= stylesheet_link_tag "admin" %> <body> <div id ="title1">Admin</div> <div class ="menu"></div> <div id ="section3"> <table id = "mytable"> <table border = "1"> <tr> <th>Username </th> <th>Email</th> <th>First Name</th> <th>Last Name</th> <th>Admin?</th> <th></th> <th></th> <th></th> </tr> <%= link_to "New User", admin_new_path %><br /> <% @users.each do |t| %> <tr> <td><%= t.username %></td> <td><%= t.email %></td> <td><%= t.firstname %></td> <td><%= t.lastname %></td> <td><%= t.admin %></td> <td><%= link_to 'Show', t %></td> <td> <%= button_to "Delete", t, method: :delete, data: { confirm: 'Are you sure?' } %></td> </tr> <% end %> </table></br> </body> </html> I can display the User database, but when I go to delete a record. I get this error No route matches [DELETE] "/users/11". I am new to rails so please remember this when trying to help. Thanks in advance. Edit: here are my routes = admin_index GET /admin(.:format) admin#index POST /admin(.:format) admin#create new_admin GET /admin/new(.:format) admin#new edit_admin GET /admin/:id/edit(.:format) admin#edit admin GET /admin/:id(.:format) admin#show PUT /admin/:id(.:format) admin#update DELETE /admin/:id(.:format) admin#destroy new_user_session GET /users/sign_in(.:format) devise/sessions#new user_session POST /users/sign_in(.:format) devise/sessions#create destroy_user_session DELETE /users/sign_out(.:format) devise/sessions#destroy user_password POST /users/password(.:format) devise/passwords#create new_user_password GET /users/password/new(.:format) devise/passwords#new edit_user_password GET /users/password/edit(.:format) devise/passwords#edit PUT /users/password(.:format) devise/passwords#update cancel_user_registration GET /users/cancel(.:format) admin#cancel user_registration POST /users(.:format) admin#create new_user_registration GET /users/sign_up(.:format) admin#new edit_user_registration GET /users/edit(.:format) admin#edit PUT /users(.:format) admin#update DELETE /users(.:format) admin#destroy projects GET /projects(.:format) projects#index POST /projects(.:format) projects#create new_project GET /projects/new(.:format) projects#new edit_project GET /projects/:id/edit(.:format) projects#edit project GET /projects/:id(.:format) projects#show PUT /projects/:id(.:format) projects#update DELETE /projects/:id(.:format) projects#destroy search /search(.:format) projects#search root / projects#index

    Read the article

  • Can extension methods be applied to interfaces?

    - by Greg
    Hi, Is it possible to apply an extension method to an interface? (C# question) That is for example to achieve the following: create an ITopology interface create an extension method for this interface (e.g. public static int CountNodes(this ITopology topologyIf) ) then when creating a class (e.g. MyGraph) which implements ITopology, then it would automatically have the Count Nodes extension. This way the classes implementing the interface would not have to have a set class name to align with what was defined in the extension method.

    Read the article

  • Items Created via IB are not being displayed

    - by Rohan
    Hello, This is what i have done so far, Made a Custom view added few objects, as shown below @interface CommUICustomSignInView : CommUICustomView { IBOutlet NSButton *pBtn; IBOutlet NSTextField *pTextField; NSTrackingArea *pTrackingArea; NSCursor *pPonitHandCursor; } Added all IBoutlet correctly, Now thru Interface builder constructed a Window controller interface builder in which added a custom view and provided this class name in the interface builder, I hope i could able to visualize you guys, now whenever i loaded this view, the item whatever i created by IB are not being displayed, Am i doing something wrong, or something missing,

    Read the article

  • Cannot get SCVMM Admin Console to Connect to Hyper-V Server 2008 R2

    - by user63250
    I cannot get SCVMM Admin console to connect to Hyper-V Server 2008. I have changed all firewall settings on the server to allow for a connection, I have even tried turning the firewall off completely. I am getting this error message: Unable to connect to the Virtual Machine Manager server xx.xxx.xxx.xx. the Virtual Machine Manager service on that servier did not respond. Verify that Virtual Machine Manager has been installed on the server and that the Virtual Machine Manager service is running. Then try to connect again. If the problem persists, restart the Virtual Machine Manager Service. ID: 1602 I have tried restarting the VMMS service, and that did not work. I have posted a similar question to this before, and was told to make sure to intall the Hyper-V agent on the Hyper-V server. I was told that SCVMM can push the agent out to the server. However, if I cannot connect to the server, how can I use SCVMM to push out the agent? Thanks for any help.

    Read the article

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • can't get to admin page after factory reset netgear wg602

    - by stefanB
    I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

    Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >