Search Results

Search found 18395 results on 736 pages for 'admin interface'.

Page 45/736 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• Filesystem access through web interface

  - by Jorge Suárez de Lis

  I have an SSH+Samba server so people can access its files from anywhere on the network. I thought it would be also interesting to provide access through a web interface, so they can access the files even when they don't have access to the VPN or a Samba/SSH client. Something like the Ubuntu One or Dropbox web interface. The http server could be on the same machine as the SSH+Samba, so it should just provide access to local files and some way to login with their username/password. Someone knows any software like this?

  Read the article

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to be able to forward all the traffic to one of these local address trhough the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 are not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• How to implement an interface member that returns void in F#

  - by Drew Noakes

  Imagine the following interface in C#: interface IFoo { void Bar(); } How can I implement this in F#? All the examples I've found during 30 minutes of searching online show only examples that have return types which I suppose is more common in a functional style, but something I can't avoid in this instance. Here's what I have so far: type Bar() = interface IFoo with member this.Bar = void Fails with FS0010: Unexpected keyword 'void' in expression.

  Read the article

• Disabling networkmanager for a specific interface

  - by bdonlan

  I'd like to do some experimentation with hostap without disabling my primary wireless interface. How do I tell networkmanager to keep its hands off a specific interface or interfaces while allowing it to continue managing all other interfaces normally? I'm using Ubuntu 9.04. (Wasn't sure if this should go on superuser or serverfault, as networkmanager isn't much of a 'server' tool - if it belongs on serverfault please feel free to move it) Edit: I've tried adding this to /etc/network/interfaces: allow-hotplug wlan2 iface wlan2 inet static address 192.168.49.1 netmask 255.255.255.0 But this has no apparent effect, even after restarting NetworkManager. Here's my /etc/NetworkManager/nm-system-settings.conf: [main] plugins=ifupdown,keyfile [ifupdown] managed=false Edit[2]: Looks like I needed to restart nm-system-settings, then NetworkManager.

  Read the article

• Network-Backup-Software with file versioning and web-interface

  - by dlang

  Dear All! I would like to backup our business-data to a remote backup-server. We would like to set-up our own backup-server running on any operating system (windows appreciated) which comes with a web-interface, that enables to restore individual versions of one file. Because budget is limited, an open-source software or at least a cheap software is a must! Unfortunately I couldn't find even a single software, which fulfills the requirements of file versioning and web-interface for single file-restore. Do any of you have already set-up such a system? Best regards, Daniel Lang

  Read the article

• Routing application traffic through specific interface

  - by UnicornsAndRainbows

  Hello All! First question here, so please go easy: I have a debian linux 5.0 server with two public interfaces. I would like to route outbound traffic from one instance of an application via one interface and the second instance through the second interface. There are some challenges: both instances of the application use the same protocol both instances of the application can access the entire internet (can't route based on dest network) I can't change the code of the application I don't think a typical approach to load balancing all traffic is going to work well, because there are relatively few destination servers being accessed in the outbound traffic, and all traffic would really need to be distributed pretty evenly across these relatively few servers. I could probably run two virtualized servers on the box and bind each of them to a different external ip, but I'm looking for a simpler solution, maybe using iproute or iptables? Any ideas for me? Thanks in advance - and I'm happy to answer any questions.

  Read the article

• Network interface selection

  - by Antonino

  Hello. Suppose I have more than a network interfaces and I want to selectively use them per application. eth0 is the standard interface with the standard gateway in the main routing table eth1 is another interface with a different gateway. Suppose I launch an application as a user "user_eth1". I used the following set of rules for iptables / ip rules. IPTABLES: iptables -t mangle -A OUTPUT -m user --uid-owner user_eth1 -j MARK --set-mark 100 iptables -t nat -A POSTROUTING -m user -uid-owner -o eth1 user_eth1 -j SNAT --to-source <eth_ipaddress> IPRULE: ip rule add fwmark 100 lookup table100 and i build "table100" as follows (no doubts on that) ip route show table main | grep -Ev ^default | while read ROUTE; do ip route add table table100 $ROUTE; done ip route add default via <default_gateway> table table100 It doesn't work at all. What's wrong with this? Thank you in advance!

  Read the article

• Interface to collect successful remote backups status

  - by Aseques

  I would like to deploy into our infrastructure a web interface that could register when the copies are finished and if for some reason they haven't. The current issue is that we are doing on site backups for customers, for each backup a mail is sent ad the end of the backup, the problems is that sometimes the mail isn't sent for a variety of reasons: System doesn't have internet Backup system crashed before sending the mail etc.. What I'd like to do is to have a web interface that the backup software cant visit after doing the backup (either if it's a success or a fail), that acknowledges that the backup has finished, after some time, I'd like to receive a report of the machines that hadn't done the backup. Is there anything remotely similar to this that I could use/adapt to our environment? UPDATE: Just found out this (paessler.com) that seems to be a privative solution of what I intended.

  Read the article

• ASA5500 series logging for management interface in transparent mode

  - by ANervousTwitch

  i have a cisco asa5520 in transparent mode. the interface is on the same subnet as some windows machines, which are generating a lot of broadcast traffic that is filling up the logs. is there any way to have it not log that its blocking those packets? its a bunch of these messages: "through-the-device packet to from management-only network is denied: udp src..." im also seeing some of those zeroconf requests that id like to drop logging for. i tried to just put a rule on the management interface, but apparently thats not allowed.

  Read the article

• Interface that Entails the Implementation of Indexer

  - by Ngu Soon Hui

  I am looking for a framework-defined interface that declares indexer. In other words, I am looking for something like this: public interface IYourList<T> { T this[int index] { get; set; } } I just wonder whether .Net framework contains such interface? If yes, what is it called? You might ask why I can't just create the interface myself. Well, I could have. But if .Net framework already has that why should I reinvent the wheel?

  Read the article

• Dynamic casting using a generic interface

  - by Phil Whittaker

  Hi Is there any way to cast to a dynamic generic interface.. Site s = new Site(); IRepository<Site> obj = (IRepository<s.GetType()>)ServiceLocator.Current.GetInstance(t) obviously the above won't compile with this cast. Is there anyway to do a dynamic cast of a generic interface. I have tried adding a non generic interface but the system is looses objects in the Loc container. Thanks Phil

  Read the article

• How to troubleshoot slow powerconnect 62xx management interface

  - by Hannes

  Our Dell Powerconnect 62xx switches have a very high packetloss on the management interface. I presume this is caused by a new appliance which uses multicast for communication but I am not sure. Our network setup is following: servers a - Dell PC6248 | servers b - Dell PC6248 |- juniper core router servers c - Dell PC6248 | What we see is that the multicast traffic arrives at all servers (but only the servers b use the multicast) and I fear that this multicast traffic floods the switch management interface. The switches' management interfaces are reachable via vlan101, all other traffic is sent over other vlans. When I tcpdump on one of the 2 servers with a vlan 101 ip address, I only get a few arp requests but almost nothing. When I try to ping between these 2 servers, it works like a charm. I would like to know what a good way is to troubleshoot this problem and maybe help me understand what is going wrong on that subnet.

  Read the article

• Enable/disable wireless interface in a bat file

  - by Herms

  Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

  Read the article

• Why is my ethernet interface in promiscuous mode

  - by nhed

  I read that seeing a flag of M in netstat -i is the way to tell which of your interfaces is in promiscuous mode I run it and I see that eth1 is in promiscuous mode $ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth1 1500 0 1770161198 0 0 0 57446481 0 0 0 BMRU lo 16436 0 97501566 0 0 0 97501566 0 0 0 LRU This seems to be the case on all the machines I checked (All Centos6.0, both virtual and physical), any idea why ethernet devices would be in such a mode unless someone was running any pcap based app (sudo lsof | grep pcap shows nothing)? I did not see any mention of promiscuous in any of the config files (sudo grep -r promis /etc) Any ideas what puts the interface into that mode and why? p.s. most of the posts I see seem to be security related, this is not that

  Read the article

• Create a web interface that starts VM's on the server side

  - by xdragonforce

  I am creating a service called TorCompute which allows for creating virtual Tor Hidden Service servers on my infrastructure (I say infrastructure, by that I mean just the 3x 32GB RAM machines waiting to be purchased). What I would like to be able to do is for users to log on, access the web interface and spin up a VM with a variable about of RAM/Disk Space. I've written the PHP for logging in and have a nice web interface, just I need the code to actually create them! How would I go about doing this? Thanks, Stewart EDIT: I will run them with VMWare Server, with vmrun

  Read the article

• Problems bringing up a second virtual network interface

  - by tubaguy50035

  I'm having issues adding a second IP address to one interface. Below is my /etc/networking/interfaces # The loopback network interface auto lo iface lo inet loopback #eth0 is our main IP address auto eth0 iface eth0 inet static address 198.58.103.* netmask 255.255.255.0 gateway 198.58.103.1 #eth0:0 is our private address auto eth0:0 iface eth0:0 inet static address 192.168.129.134 netmask 255.255.128.0 #eth0:1 is for www.site.com auto eth0:1 iface eth0:1 inet static address 198.58.104.* netmask 255.255.255.0 gateway 198.58.104.1 When I run /etc/init.d/networking restart, I get a fail error about bringing up eth0:1: RTNETLINK answers: File exists Failed to bring up eth0:1. Any reason this would be? I didn't have any problems with I first set up eth0 and eth0:0.

  Read the article

• Is there a generic interface wrapper framework

  - by epitka

  Is there a framework or a native way in .net to dynamically generate wrappers for specified interface. I need a way to say, here is a type I have and here is the interface I want to wrap around it, and for each method it the interface forward calls to these methods on the type provided.

  Read the article

• First iPhone App View Position Problem

  - by hytparadisee

  I am closely following the instructions given in the tutorial "Your First iPhone Application" on apple ADC. In the interface builder, I have set up a button positioned on the top according to the Apple Interface Guidelines. It runs without trouble if I simulate the interface in IB. However, if I run the built app, I get what is shown here. If you look at the view clearly, you will see that the entire view has been shifted up. And the magnitude of the shift is exactly the height of the status bar. And that's why the there is blank space at the bottom of the window, which was white instead of red. I have tried turning on the "Simulated Interface Elements", but that doesn't work either. The problem persists on real devices as well. However, using the "Simulate Interface" from IB looks fine. Any help is appreciated. Yun Tao

  Read the article

• Problem using a COM interface as parameter

  - by Cesar

  I have the following problem: I have to projects Project1 and Project2. In Project1 I have an interface IMyInterface. In Project2 I have an interface IMyInterface2 with a method that receives a pointer to IMyInterface1. When I use import "Project1.idl"; in my Project2.idl, a #include "Project1.h" appears in Project2___i.h. But this file does not even exist!. What is the proper way to import an interface defined into other library into a idl file? I tried to replace the #include "Project1.h" by *#include "Project1_i.h"* or *#include "Project1_i.c"*, but it gave me a lot of errors. I also tried to use importlib("Project1.tlb") and define my interface IMyInterface2 within the library definition. But when I compile Project2PS project, an error is raised (something like dlldata.c is not generated if no interface is defined). I tried to create a dummy Project1.h. But when Project2___i.h is compiled, compiler cannot find MyInterface1. And if I include Project1___i.h I get a lot of errors again! Apparently, it is a simple issue, but I don't know how to solve it. I'm stuck with that!. By the way, I'm using VS2008 SP1. Thanks in advance.

  Read the article

• Making an asynchronous interface appear synchronous to mod_python users

  - by Trey

  I have a Python-driven web interface powered by Apache 2.2 with mod_python and Python 2.4. I need to make an asynchronous process appear synchronous to users of this web interface. When users access one module on this website: An external SOAP interface will be contacted with a unique identifier and will respond with a number N The external interface will respond asynchronously by contacting a SOAP server on my machine between 1 and 10 times (the number N tells us how many responses we will receive) I need to somehow aggregate these responses and pass them to the original module which will display the information back to the user. The goal is to make the process appear synchronous to the user. What is the best way to handle this synchronization issue? Is this something Twisted would be well-suited for? I am not restricting myself to Python for the solution, though it is preferred because everything else on the server is in Python. I prefer a solution that is both scalable and will take a minimal amount of programming time (though I understand that these attributes are somewhat at odds).

  Read the article

• Java : Inner class of an interface (from google guice)

  - by bsreekanth

  Hello, I was going through the source of google guice, and found an unfamiliar piece of code. It would be great learning if someone can clarify it. I have very basic understanding of inner classes, as they keep the implementation details close to the public interface. Otherwise the inner class may pollute the namespace. Now, I see the below lines at public static final Scope SINGLETON = new Scope() { public <T> Provider<T> scope(final Key<T> key, final Provider<T> creator) { return new Provider<T>() { ......... } It assign an inner class instance to the static variable, but Scope is an interface defined as (at) public interface Scope Is it possible to instantiate the interface?? or is it a succinct syntax for an anonymous implementation of an interface?? If anyone can explain what the author is intended by multiple nested classes above (Scope and Provider), and why it make sense to implement this way, it would help me to understand. thanks.

  Read the article

• What is marker interface?

  - by Rajesh

  What is the use of extending marker interface.

  Read the article

• How to make Generic Object in java implements an interface

  - by ahmed elbagoury

  I want to have a generic object that implements an interface. I mean if i have a class A Class A <E>{ E x; } I want to make sure that x will implement a particular interface(myInterface). In other words, that the type E implements an interface.

  Read the article

• Why does the check for an interface fail?

  - by chobo

  I have a class that implements an interface. In another area of the code I check if that class instance contains that interface, but it doesn't work. The check to see if the class contains the interface always fails (false) when it should be true. Below is a simple representation of what I am trying to accomplish. Example public interface IModel { bool validate(); } public class SomeModel : IModel { public SomeModel { } public bool Validate() { return true; } } // Dummy method public void Run() { SomeModel model = new SomeModel(); if (model is IModel) { string message = "It worked"; } else { string message = "It failed"; } }

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >