Search Results

Search found 11903 results on 477 pages for 'ip forwarding'.

Page 43/477 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• pptpd-logwtmp.so config wrong ip address

  - by rgc

  i have setup a pptp vpn on ubuntu 10.04, and i config local ip address , remote ip address as following: local IP address 10.0.30.100 remote IP address 192.168.13.100 after i use windows to connect to vpn server in windows , i only could send packets, can not receive any packets. i also check the pptp log in ubuntu server, and find this strange thing rcvd [IPCP ConfAck id=0x1 <compress VJ 0f 01> <addr 10.0.30.100>] rcvd [IPCP ConfReq id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] sent [IPCP ConfAck id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] Cannot determine ethernet address for proxy ARP local IP address 10.0.30.100 remote IP address 192.168.13.100 pptpd-logwtmp.so ip-up ppp0 **172.25.146.174** i did not set 172.25.146.174, it should be 192.168.13.100, can anyone tell me what should i do to fix this problem?

  Read the article

• Domain names timing out after VPS IP change

  - by Fourjays

  I rent a CentOS 5 VPS from a UK-based provider, with DirectAdmin also installed. On Thursday night, they carried out planned maintenance to changed the two IPs I had been assigned to two new ones. On Friday, after the change had taken place, I updated my domain name records to reflect the IP change. Since then, all of the domains pointing to the VPS are timing out. Additionally, DirectAdmin was also not responding, but was was resolved by running the ipswap scripts as found in the DirectAdmin knowledgebase. It did not fix my domains though. I have contacted the VPS provider but I have been waiting for a response for some time now. I have checked again, and again, and all the IPs referenced in DirectAdmin are correct. If I go to the server IP in my browser it responds with "Apache is functioning normally." Email accounts on the server are also functioning correctly. But if I access a domain itself, it times out. Running a ping and a DNS look-up, I can confirm the nameserver IPs are correct. If I run a trace route it reaches an IP that is similar to my VPS IPs (last 2 blocks are different) before timing out (it never shows my server IP). I am relatively new to VPS management so don't have a vast wealth of experience with troubleshooting problems on them. I have checked all of the httpd configuration files, which don't seem to have any IP references in them at all. Looking in the Apache error logs, what errors there are do not coincide with times I have tried to access the site. Is this issue at my provider's end? Is there anything else I can check or test, to rule out post-IP-change problems with my server configuration? It was all running fine prior to the IP change.

  Read the article

• Open port in gufw is closed, no incoming connection on deluge

  - by user66987

  I have a problem configuring gufw. I open ports on it, but when i test in deluge it shows as closed. Any help on setting up the firewall would be greatly appreciated. This is the output I get on the firewall in terminal: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:53 0.0.0.0:* LISTEN 1346/dnsmasq tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 970/cupsd tcp 0 0 0.0.0.0:55521 0.0.0.0:* LISTEN 17362/python tcp6 0 0 ::1:631 :::* LISTEN 970/cupsd tcp6 0 0 :::55521 :::* LISTEN 17362/python udp 0 0 10.0.0.125:1900 0.0.0.0:* 17362/python udp 0 0 127.0.0.1:1900 0.0.0.0:* 17362/python udp 0 0 0.0.0.0:1900 0.0.0.0:* 17362/python udp 0 0 127.0.0.1:53162 0.0.0.0:* 17362/python udp 0 0 127.0.0.1:53 0.0.0.0:* 1346/dnsmasq udp 0 0 0.0.0.0:68 0.0.0.0:* 1312/dhclient udp 0 0 10.0.0.125:36948 0.0.0.0:* 17362/python udp 0 0 0.0.0.0:37240 0.0.0.0:* 17362/python udp 0 0 10.0.0.125:6771 0.0.0.0:* 17362/python udp 0 0 127.0.0.1:6771 0.0.0.0:* 17362/python udp 0 0 0.0.0.0:6771 0.0.0.0:* 17362/python udp 0 0 10.0.0.125:50034 0.0.0.0:* 17362/python udp 0 0 0.0.0.0:58340 0.0.0.0:* 982/avahi-daemon: r udp 0 0 0.0.0.0:5353 0.0.0.0:* 982/avahi-daemon: r udp 0 0 0.0.0.0:56947 0.0.0.0:* 17362/python udp 0 0 127.0.0.1:57059 0.0.0.0:* 17362/python udp6 0 0 :::49793 :::* 982/avahi-daemon: r udp6 0 0 :::5353 :::* 982/avahi-daemon: r kenneth@kenneth-K53U:~$ sudo ufw status Status: aktive Til Handling Fra --- -------- --- 6881:6891/tcp ALLOW Anywhere 6881:6891/udp ALLOW Anywhere 55521/tcp ALLOW Anywhere 6881:6891/tcp ALLOW Anywhere (v6) 6881:6891/udp ALLOW Anywhere (v6) 55521/tcp ALLOW Anywhere (v6) I also want to be able to use the firewall with linuxdc, so I need other ports open as well. This is connected to the firewall. Because when I turn off the firewall, the port is open. So this is not a problem with my modem. Do I need the firewall? The broadband modem has a hardware firewall. Update: Forgot to add. When my firewall is inactive, it closes ports after a time. So when I use linuxdc, I have to flush iptabels and activating it again. Is this supposed to do this when the firewall is deactivated? Update again: All my ports are closed now, flushing the iptable does not work anymore. I have uninstalled gufw, but still all my ports are closed. And to say it again, this has nothing to do with my broadband modem since it worked when I used windows 7. I need help to open the ports.

  Read the article

• Possible to IPSec VPN Tunnel Public IP Addresses?

  - by caleban

  A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

  Read the article

• Connect to MySQL on remote server from inside python script (DB API)

  - by Atul Kakrana

  Very recently I have started to write python scripts that need to connect few databases on mySQL server. The problem is that when I work from office my script works fine but running a script from my home while on office VPN generates connection error. I also noticed the mySQL client Squirrel also cannot connect from my home but works fine on Office computer. I think both are giving problem for the same reason. Do I need to create a ssh tunnel and forward the port? If yes how do I do it? mySQL is installed on server I have ssh access. Please help me on this AK

  Read the article

• Getting a domain sub-directory url for a new server

  - by Xianlin

  I have an web application server running tomcat and i need to publish my APIs to internet users. However I don't have a domain name for this server and I can only put the ip address of this server (e.g. 145.XXX.XXX.XXX) to point out where my API xml files are located. I have another web server running with a domain name "http://www.webserver.com" registered on the internet and I want to make use of its domain name to server my web application server API xml files location. How can I do that? using "www.webserver.com/api" or using "api.webserver.com"? which is better? Also I wonder if I want to publish a "rstp://145.XXX.XXX.XXX" web link for video streaming purpose, can I use "rstp://www.webserver.com/api" to replace it and how to do it? I always thought the url contain domain sub-directory name cannot point to another IP address, it only can point to another folder location on the webserver itself.

  Read the article

• IP queue buffer

  - by summerbulb

  I seem to have an issue with IP queue. I have a linux machine that I am using to run some experiments. The linux machine is configured to be a router, having two NICs, connecting two other computers, and managing their network traffic. All incoming packages are captured, using iptables, and analyzed by a C application. The application analyzing the packets has a built-in delay, as part of the experiment. So I have one very fast computer sending packets through my linux-router and a (relatively) slow linux-router that analyses and deals with the packets, one by one. This situation leads to the fact that when I fire up a sender application on one of the computers connected to the linux-router, my IP queue on the linux-router gets filled up (almost) instantaneously. The IP queue's max length is currently set to 1024, and if it overflows, the packets are dropped. This is expected and i'm OK with it. But, (and this is where it gets interesting), every now and then I get the following error: "Failed to receive netlink message: No buffer space available" At start, I thought this was due to the IP queue overflow, but after some analysis i found that sometimes I get the error even if the IP queue buffer did not overflow, and sometime I DON'T get the message even though the buffer DID overflow. When I run > cat /proc/net/ip_queue, I get the following table (also used to monitor the IP queue overflow): Peer PID : 27389 Copy mode : 2 Copy range : 65535 Queue length : 0 Queue max. length : 1024 Queue dropped : 1166875 Netlink dropped : 2916 Looking at the last two values, Queue dropped seems to refer to packets that did not manage to get into the IP queue because the buffer was full. I can see this value rise as I bombard the linux-router. Netlink dropped ( as it's name implies :) ) seems to have to do with the error i'm getting. I did my best to search for material on this error, but wasn't able to find anything that seemed to point me in the required direction. Bottom line: Why am I getting this error and what can I do to avoid it?

  Read the article

• How do I X forward a Windows application to a Linux system using ssh?

  - by triunenature

  Ok, so if I have two Linux Machines (A and B) and I have a program on one, and want to run it on be I do: user@LinuxA:~$ ssh -X LinuxB user@LinuxB:~$ programName (Displays on LinuxA machine) Ok same thing, WindowsA LinuxB (Program on Linux) Start Xming X Server on Windows Run Putty, use x11 port forward with :0.0 After connect to LinuxB, run program, it loads in Windows! Now here is the question, WindowsA LinuxB, (Program on Windows) Run Windows Program On Linux, using a windows resources. How to make it work? BTW, I know it can because years ago, I read a white paper on it, but never actually tested it out.

  Read the article

• A record point not working

  - by Peter

  I'm trying to do an A record point to transfer the hosting of a domain from one provider to another. I don't want to change the nameservers as this will result in emails going down. The output when I dig for the domain shows the correct IP (78.46.63.87) for the new host. I know A records can take a while to propagate but Its been over 36hrs now and I still keep getting this error(below) when I try to pull the domain through as an addon domain via Cpanel on the new host. Are the old nameservers conflicting with the A record point? here's the error: Using nameservers with the following IPs: 208.80.125.4,208.80.126.4,208.80.124.4,208.94.148.4 Sorry, the domain is already pointed to an IP address that does not appear to use DNS servers associated with this server. Please transfer the domain to this servers nameservers or have your administrator add one of its nameservers to /etc/ips.remotedns and make the proper A entries on that remote nameserver.

  Read the article

• iptables, forward traffic for ip not active on the host itself

  - by gucki

  I have kvm guest which's netword card is conntected to the host using a tap device. The tap device is part of a bridge on the host together with eth0 so it can access the public network. So far everything works, the guest can access the public network and it can be accessed from the public network. Now the kvm process on the host provides a vnc server for the guest which listens on 127.0.0.1:5901 on the host. Is there any way to make this vnc server accessible by the ip address which the guest is using (ex. 192.168.0.249), without interrupting the guest from using the same ip (port 5901 is not used by the guest)? It should also work when the guest is not using any ip address at all. So basically I just want to fake IP xx is on the host and only answer/ forward traffic to port 5901 to the host itself. I tried using this NAT rule on the host, but it doesn't work. Ip forwarding is enabled at the host. iptables -t nat -A PREROUTING -p tcp --dst 192.168.0.249 --dport 5901 -j DNAT --to-destination 127.0.0.1:5901 I assume this is because the IP 192.168.0.249 is not not bound to any interfaces and so no ARP requests for it get answered and so no packets for this IP arrive at the host. How can make it work? :)

  Read the article

• Blackberry Enterprise Server v5.x not forwarding mail to devices

  - by TheWellington

  My BlackBerry enterprise server recently stopped forwarding messages to devices. In fact, the server claims that the last time it communicated with all the devices associated with it, was on Thursday night (2 nights ago.) The catch is this, the Exchange server is running properly (or as properly as Exchange can run :) ) The SQL server seems to be running properly. And the Blackberry Enterprise server seems to be running correctly. Other than the fact that the server has not communicated with my device since Thursday, and the fact that I am not getting messages, there is nothing wrong. How do I get these message to be forwarded to devices again? I have restarted the BES services int he order suggested by the BlackBerry folks

  Read the article

• Port forwarding (portmap) works only locally

  - by Tag Wint

  There are four hosts hostA winXP hostB Win2003 hostC Linux RHEL hostD Linux RHEL hostA cannot connect to C and D directly, but B can hostA connects to hostB using VPN hostB and hostC belong to the same subnet1 hostD is in subnet2 From hostA I need to connect to hostC and hostD by SSH. Now I can do it as follows: 1.connecting from hostA to hostB by RDP logon and there: 2.start putty client. I'd like to omit step 1 and connect from A to C and D directly On hostB I have admin acoount and configure port forwarding as follows: netsh interface portproxy add v4tov4 listenport=N1 connectaddress=hostC_IP connectport=N2 netsh interface portproxy add v4tov4 listenport=N3 connectaddress=hostD_IP connectport=N2 netsh interface portproxy show all: Listen on IPv4: Connect to IPv4: Address Port Address Port --------------- ---------- --------------- ---------- * N1 hostC_IP N2 * N3 hostD_IP N2 Now from hostB I can connect to either C and D: ssh localhost:N1 ssh localhost:N3 from hostA ssh hostB:N1 works too, but ssh hostB:N3 DON'T I guess the reason might be different subnets, still have no idea how to fix it. What should I do?

  Read the article

• OpenVPN on ec2 bridged mode connects but no Ping, DNS or forwarding

  - by michael

  I am trying to use OpenVPN to access the internet over a secure connection. I have openVPN configured and running on Amazon EC2 in bridge mode with client certs. I can successfully connect from the client, but I cannot get access to the internet or ping anything from the client I checked the following and everything seems to shows a successful connection between the vpn client/server and UDP traffic on 1194 [server] sudo tcpdump -i eth0 udp port 1194 (shows UDP traffic after establishing connection) [server] sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] sudo iptables -L -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- ip-W-X-Y-0.us-west-1.compute.internal/24 anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] openvpn.log Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 [localhost] Inactivity timeout (--ping-restart), restarting Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 SIGUSR1[soft,ping-restart] received, client-instance restarting Wed Oct 19 03:41:31 2011 MULTI: multi_create_instance called Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Re-using SSL/TLS context Wed Oct 19 03:41:31 2011 a.b.c.d:57889 LZO compression initialized Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Control Channel MTU parms [ L:1574 D:166 EF:66 EB:0 ET:0 EL:0 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Local Options hash (VER=V4): '360696c5' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Expected Remote Options hash (VER=V4): '13a273ba' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 TLS: Initial packet from [AF_INET]a.b.c.d:57889, sid=dd886604 ab6ebb38 Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=EXAMPLE_CA/[email protected] Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=localhost/[email protected] Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Oct 19 03:41:37 2011 a.b.c.d:57889 [localhost] Peer Connection Initiated with [AF_INET]a.b.c.d:57889 Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 PUSH: Received control message: 'PUSH_REQUEST' Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 SENT CONTROL [localhost]: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route-gateway W.X.Y.Z,ping 10,ping-restart 120,ifconfig W.X.Y.Z 255.255.255.0' (status=1) Wed Oct 19 03:41:40 2011 localhost/a.b.c.d:57889 MULTI: Learn: (IPV6) -> localhost/a.b.c.d:57889 [client] tracert google.com Tracing route to google.com [74.125.71.104] over a maximum of 30 hops: 1 347 ms 349 ms 348 ms PC [w.X.Y.Z] 2 * * * Request timed out. I can also successfully ping the server IP address from the client, and ping google.com from an SSH shell on the server. What am I doing wrong? Here is my config (Note: W.X.Y.Z == amazon EC2 private ipaddress) bridge config on br0 ifconfig eth0 0.0.0.0 promisc up brctl addbr br0 brctl addif br0 eth0 ifconfig br0 W.X.Y.X netmask 255.255.255.0 broadcast W.X.Y.255 up route add default gw W.X.Y.1 br0 /etc/openvpn/server.conf (from https://help.ubuntu.com/10.04/serverguide/C/openvpn.html) local W.X.Y.Z dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;server W.X.Y.0 255.255.255.0 server-bridge W.X.Y.Z 255.255.255.0 W.X.Y.105 W.X.Y.200 ;push "route W.X.Y.0 255.255.255.0" push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" tls-auth ta.key 0 # This file is secret user nobody group nogroup log-append openvpn.log iptables config sudo iptables -A INPUT -i tap0 -j ACCEPT sudo iptables -A INPUT -i br0 -j ACCEPT sudo iptables -A FORWARD -i br0 -j ACCEPT sudo iptables -t nat -A POSTROUTING -s W.X.Y.0/24 -o eth0 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward Routing Tables added route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface W.X.Y.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 0.0.0.0 W.X.Y.1 0.0.0.0 UG 0 0 0 br0 C:>route print =========================================================================== Interface List 32...00 ff ac d6 f7 04 ......TAP-Win32 Adapter V9 15...00 14 d1 e9 57 49 ......Microsoft Virtual WiFi Miniport Adapter #2 14...00 14 d1 e9 57 49 ......Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Net work Adapter 10...00 1f d0 50 1b ca ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 17...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 18...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 36...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.2.1 10.1.2.201 25 10.1.2.0 255.255.255.0 On-link 10.1.2.201 281 10.1.2.201 255.255.255.255 On-link 10.1.2.201 281 10.1.2.255 255.255.255.255 On-link 10.1.2.201 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.2.201 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.2.201 281 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.1.2.1 Default =========================================================================== C:>tracert google.com Tracing route to google.com [74.125.71.147] over a maximum of 30 hops: 1 344 ms 345 ms 343 ms PC [W.X.Y.221] 2 * * * Request timed out.

  Read the article

• Opening and Testing Ports on Modem > Router Connection

  - by JakeTheSnake

  Working off of my last question, I can access my server's FTP over the LAN but not over the internet. I'm using Filezilla on port 666. My router/modem configuration is as such (similar to other post): 1) Modem connects to WAN 2) WAN port on modem connects to LAN port on Router 3) Modem internal IP address is 192.168.0.254 4) Router internal IP address is 192.168.0.1 5) Modem has DHCP turned OFF 6) Router has DHCP turned ON 7) Router is running Tomato firmware and it's set as 'Router' (not 'Gateway') 8) The internet is working (just had to say that) I've set up port forwarding both on the modem and router - both route port 666 to the IP address of 192.168.0.3 (TCP); that is the IP address of the server which has FileZilla running. I don't know if that's hindering anything but I've also tried it with just the modem and just the router...same result. I've also tried setting the server to be DMZ (both on router and modem). Neither router nor modem have anything in their logs about denying inbound traffic on port 666 so my ability to troubleshoot stops there. I've tried contacting my ISP (Telus, running on mobility plan...it's a "Smart" Hub) but they weren't much help. They said they only block port 25 and 80 and maybe a few others, but not most ports. I test whether or not the port is open by going to canyouseeme.org - I don't know whether or not that would produce a 'connection refused' result just based on the fact that the FTP requires a login...I'm not well versed on this matter. FWIW, sometimes I get a 'connection refused' error on canyouseeme.org but mostly it's 'connection timed out'. I don't know what else to do at this point.

  Read the article

• X forwarding over SSH from Mac to a Linux box

  - by Checkers

  I need run Mac applications on a remote Mac machine and display it on a local Linux machine's X server (a lot of articles on the Internet seem to be detailing how would you do it the opposite way). $ ssh -X mac-box $ cd /Developer/Applications/Xcode.app $ ./Contents/MacOS/Xcode Sat Oct 3 20:41:26 mac-box.local Xcode[15634] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL. ^C My $DISPLAY variable appears to be empty. What should it look like so that forwarding works correctly? Can I run OSX applications this way at all?

  Read the article

• xinet vs iptables for port forwarding performance

  - by jamie.mccrindle

  I have a requirement to run a Java based web server on port 80. The options are: Web proxy (apache, nginx etc.) xinet iptables setuid The baseline would be running the app using setuid but I'd prefer not to for security reasons. Apache is too slow and nginx doesn't support keep-alives so new connections are made for every proxied request. xinet is easy to set up but creates a new process for every request which I've seen cause problems in a high performance environment. The last option is port forwarding with iptables but I have no experience of how fast it is. Of course, the ideal solution would be to do this on a dedicated hardware firewall / load balancer but that's not an option at present.

  Read the article

• X11 forwarding - have window showing on two computers.

  - by Tim

  I currently have 2 desks: one with a mac, the other with a 2 Linux computers on. One of those Linux computers is constantly on, so I would run the chat app on that (pidgin, most likely). I can run pidgin on Mac by sshing into the Linux computer with "ssh -X", i.e. X11 forwarding. However, I want to have the chat windows viewable on both computers simultaneously (or at the very least, by entering a command or whatever). Is this possible and if so, how? (Also: I know that it'd be possible via VNC or whatever, but yuck - X11 on mac is bad enough.) Thanks, Tim

  Read the article

• Setting up a Time Capsule with port forwarding

  - by Kaji

  Our old AirPort Extreme station hit EOL, so we decided to upgrade it to a Time Capsule. Along the way, we're trying to also set it up with a separate guest network and port forwarding/NAT, however we're having trouble setting it up so that the time capsule is handling the DHCP leases instead of the router. We've got DSL through Verizon through a Westell modem/router to the Time Capsule. Done the RTFM thing, and we haven't been able to get it to work. Can anyone explain how to get things set up properly for this configuration?

  Read the article

• Setting up a Time Capsule with port forwarding

  - by Kaji

  Our old AirPort Extreme station hit EOL, so we decided to upgrade it to a Time Capsule. Along the way, we're trying to also set it up with a separate guest network and port forwarding/NAT, however we're having trouble setting it up so that the time capsule is handling the DHCP leases instead of the router. We've got DSL through Verizon through a Westell modem/router to the Time Capsule. Done the RTFM thing, and we haven't been able to get it to work. Can anyone explain how to get things set up properly for this configuration?

  Read the article

• Configuring port forwarding on Fortigate 50B

  - by GomoX

  I can't for the life of me get port forwarding to work on my Fortigate 50B. I followed the setup tips described on this other SF thread with no success. The only specific difference I can find is we are using load balancing through 2 different internet uplinks. Is there any caveat specific to this scenario that I might be missing? If you need any specific additional information please ask because I think I have checked everything: Virtual IP mapping on external interface wan1 ACCEPT all from any on wan1 to the corresponding server on internal No seeming offending firewall rules (any specific pitfalls that I might want to check for?)

  Read the article

• Quick change of SSH tunnel port forwarding options for SOCKS proxy

  - by user1335897

  The goal is to have access to internet thru SSH tunneling to SOCKS proxy. Me - ssh-on-my-vps - SOCKS proxy - internet Thing is I want to be able to quickly change the SOCKS proxy in this chain. If I use port forwarding on ssh, I assume I have to re-establish SSH tunnel with new SOCKS proxy address in parameters whenever I want to change proxy. Is that right? If it is, then I probably should always point SSH tunnel to localhost listening proxy server which will send requests to specified SOCKS proxy. So what local proxy I should choose that allows to easily change the destination SOCKS proxy via maybe reading from local file where I would put the SOCKS proxy address or via specifying new SOCKS address in its web-admin page?

  Read the article

• How to host an ssh server?

  - by balki

  Hi, I have a broadband internet connection. I have an wireless modem (Airtel India). I don't have a static ip address. I want to host a ssh/web/ftp server to be visible to the outside world just for testing and learning purpose so I can ask my friend to connect to my current ip address and test. My modem has an admin interface which allows to port forward and open ports. I set up ssh server as shown and checked if port 22 is open using this website , Port Scan And port 22 is open. I have an openssh server running and it works if i do, ssh [email protected] which is my local ip address but doesn't work if i do ssh [email protected] where 122.xx.xx.xx is my external ip address of my modem which i checked from whatismyipaddress.com. Since it looks like the port is open, I wonder if there is some setting I need to change in my server config to expose my server. How should I go about solving this?

  Read the article

• Network with bridge and port forwarding?

  - by rafek

  Hi! Below is my current (and planned) home network configuration. I would like to connect my non-wifi-capable desktop to my home network. The question is: HOW? What device do I need? The primary requiremen is that I need to be able to forward ports to my desktop. How would I achieve this? Is there something like "double port forwarding"? Could anyone please explain this configuration to me? Thank you in advance!

  Read the article

• Network with bridge and port forwarding?

  - by rafek

  Hi! Below is my current (and planned) home network configuration. I would like to connect my non-wifi-capable desktop to my home network. The question is: HOW? What device do I need? The primary requiremen is that I need to be able to forward ports to my desktop. How would I achieve this? Is there something like "double port forwarding"? Could anyone please explain this configuration to me? Thank you in advance!

  Read the article

• spam email forwarding by server

  - by kikio

  Let's start with this scenario: We have a mailbox (i.e. in yahoo), every message is sent by this account, marked as spam by Gmail spam filter. (because the address or sender IP is blacklisted, not because of content) There is a server which is able to forward incoming messages to another address (email forwarding), for example, to a Gmail mailbox. And it is not blacklisted. The question is: If we send a message, through the dirty mailbox to the server, and server forward it to a Gmail mailbox, will it marked as spam by spam filters?

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >