Search Results

Search found 12527 results on 502 pages for 'red eyes dev'.

Page 43/502 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• CentOS - Add additional hard drive raid arrays on Dell Perc 5/i card

  - by Quanano

  We have a Dell Poweredge 2900 system with Dell Perc 5/i card and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on one raid array on this controller with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l: Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v: [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod: Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log blkid: /dev/sda1: UUID="bc4777d9-ae2c-4c58-96ea-cedb342b8338" TYPE="ext4" /dev/sda2: UUID="j2wRZr-Mlko-QWBR-BndC-V2uN-vdhO-iKCuYu" TYPE="LVM2_member" /dev/mapper/vg_lal2server-lv_root: UUID="9238208a-1daf-4c3c-aa9b-469f0387ebee" TYPE="ext4" /dev/mapper/vg_lal2server-lv_swap: UUID="dbefb39c-5871-4bc9-b767-1ef18f12bd3d" TYPE="swap" /dev/mapper/vg_lal2server-lv_home: UUID="ec698993-08b7-443e-84f0-9f9cb31c5da8" TYPE="ext4" dmesg shows: megaraid_sas: fw state:c0000000 megasas: fwstate:c0000000, dis_OCR=0 scsi2 : LSI SAS based MegaRAID driver scsi 2:0:0:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:1:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:2:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:3:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:4:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:5:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:8:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 scsi 2:0:9:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 i.e. the 3 RAID Arrays Seagate Hitatchi and Fujitsu hard drives respectively. FURTHER UPDATE I have installed the megaraid storage manager console and connected to the server. It appears that the two CentOS installation hard drives are OK. The other 6 drives, one raid array of 4 and one raid array of 2 disks. The other drives are listed as (Foreign) Unconfigured Good.

  Read the article

• dual boot install--no GRUB

  - by Jim Syyap

  My computer recently had a hardware upgrade and now runs on Windows 7. I decided to install Ubuntu 11.04 as dual boot using the ISO I got from ubuntu.com downloaded onto my USB stick. Restarting with the USB stick, I was able to install Ubuntu 11.04 choosing the option: Install Ubuntu 11.04 side by side with Windows 7 (or something like that). No errors were encountered on installation. However on restarting, there was no GRUB; the system went straight into Windows 7. Looking for answers, I found these: http://essayboard.com/2011/07/12/how-to-dual-boot-ubuntu-11-04-and-windows-7-the-traditional-way-through-grub-2/ http://ubuntuforums.org/showthread.php?t=1774523 Following their instructions, I got: Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Syslinux MBR (3.61-4.03) is installed in the MBR of /dev/sdb. => Grub2 (v1.99) is installed in the MBR of /dev/sdc and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos7)/boot/grub on this drive. sda1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /grldr /bootmgr /Boot/BCD /grldr sda2: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /Windows/System32/winload.exe sdb1: __________________________________________________ ________________________ File system: vfat Boot sector type: SYSLINUX 4.02 debian-20101016 ...........>...r>....... ......0...~.k...~...f...M.f.f....f..8~....>2} Boot sector info: Syslinux looks at sector 1437504 of /dev/sdb1 for its second stage. SYSLINUX is installed in the directory. The integrity check of the ADV area failed. According to the info in the boot sector, sdb1 starts at sector 0. But according to the info from fdisk, sdb1 starts at sector 62. Operating System: Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg /ldlinux.sys sdc1: __________________________________________________ ________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdc2: __________________________________________________ ________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdc5: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc6: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: sdc7: __________________________________________________ ________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdc8: __________________________________________________ ________________________ File system: swap Boot sector type: - Boot sector info: Going back into Ubuntu and running sudo fdisk -l , I got these: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002f393 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 19458 156185600 7 HPFS/NTFS Disk /dev/sdb: 2011 MB, 2011168768 bytes 62 heads, 62 sectors/track, 1021 cylinders Units = cylinders of 3844 * 512 = 1968128 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000f2ab9 Device Boot Start End Blocks Id System /dev/sdb1 * 1 1021 1962331 c W95 FAT32 (LBA) Disk /dev/sdc: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00261ddd Device Boot Start End Blocks Id System /dev/sdc1 * 1 60657 487222656+ 7 HPFS/NTFS /dev/sdc2 60657 121600 489527681 5 Extended /dev/sdc5 120563 121600 8337703+ 82 Linux swap / Solaris /dev/sdc6 120073 120562 3930112 82 Linux swap / Solaris /dev/sdc7 60657 119584 473328640 83 Linux /dev/sdc8 119584 120072 3923968 82 Linux swap / Solaris Should I proceed and do the following? Assuming Ubuntu 11.04 was installed on device sdb1, do this: sudo mount /dev/sdb1 /mnt Then do this: sudo grub-install--root-directory=/mnt /dev/sdb Notice there are two dashes in front of the root directory, and I'm not using sdb1 but sdb. Since the command in step 15 had reinstalled Grub 2, now we need to unmount the /mnt (i.e. sdb1) to clean up. Do this: sudo umount /mnt Reboot and remove Ubuntu 11.04 CD/DVD from disk tray. Log into Ubuntu 11.04 (you have no choice but it will make you log into Ubuntu 11.04 at this point). Open up a terminal in Ubuntu 11.04 (using real installation, not live CD/DVD). Execute this command: sudo update-grub Reboot the machine.

  Read the article

• Oracle application - files missing in the Mount point in UNix server

  - by arun_V

  My oracle application test instance is down, When I browse through the Unix server, I couldn’t find any files in the mount point,U01 U06 or U10, when I put BDF command it shows the following $ bdf Filesystem kbytes used avail %used Mounted on /dev/vg00/lvol3 204800 35571 158662 18% / /dev/vg00/lvol1 299157 38506 230735 14% /stand /dev/vg00/lvol8 1392640 1261068 123620 91% /var /dev/vg00/lvol7 1327104 825170 470631 64% /usr /dev/vg00/lvol4 716800 385891 310746 55% /tmp /dev/vg00/lvol6 872448 814943 53936 94% /opt /dev/vg00/lvolssh 32768 13243 18306 42% /opt/openssh /dev/vg00/lvol5 204800 187397 16334 92% /home /dev/vg00/lvolback 512000 472879 36704 93% /backup dg-ora04:/dgora03_u10 204800 167088 35416 83% /u10 dg-ora04:/dgora03_u06 204800 167088 35416 83% /u06 dg-ora04:/dgora03_u01 204800 167088 35416 83% /u01 Why can't I see any files inside the mount points?

  Read the article

• How to mount encrypted volume at login (Ubuntu 12.04, pam_mount)

  - by Nick Lothian

  I'm trying to get pam_mount working on Ubuntu 12.04. I have /dev/sda1 (encrypted partition) with /dev/dm-1 (ext4 formatted) inside it. Should ~/.pam_mount.conf.xml be trying to mount /dev/sda1 or /dev/dm-1? If I use the line: <volume fstype="ext4" path="/dev/dm-1" mountpoint="~/slowstore" options="rw" /> then it nearly works. It prompts for the password (ok, I'd like pam_mount to do that for me, but still..) then I get: pam_mount(rdconf2.c:126): checking sanity of luserconf volume record (/dev/dm-1) pam_mount(rdconf2.c:132): user-defined volume (/dev/dm-1), volume not owned by user If I do: sudo chown nick:disk /dev/dm-1 Then re-login the encrypted partition mounts correctly (ignoring th fact I have to reneter the password). However, if I log out completely the ownership on /dev/dm-1 gets reset to root:disk. What am I doing wrong?

  Read the article

• jQuery multiple themes on one page

  - by lloydphillips

  This is driving me NUTS! I've followed the post here which just doesn't seem to be working: http://www.filamentgroup.com/lab/using_multiple_jquery_ui_themes_on_a_single_page/ I have a base theme, for examples sake it's the Smoothness theme from the jQuery UI gallery. Then I have a 'red' theme which basically colours the buttons red. Here is the theme I created. So I go to download my theme. Choose Advanced settings, set the scope to 'red' and my theme folder name to 'red' and download. First of all I'm not entirely 100% sure which folder I'm to copy over to my project is it the 'development-bundle\themes' folder (which contains my red folder) or the '\css\red' folder? I've tried both. The post above seems to suggest if I copy my themes folder and link to my theme in the css it'll work when I add a class of 'red' to a wrapper div or element. So I've linked the themes like so in my file: <link type="text/css" href="themes/base/jquery.ui.all.css" rel="stylesheet" /> <link type="text/css" href="themes/red/jquery.ui.all.css" rel="stylesheet" /> The base theme loads and works all honkey doorey but the red theme doesn't. I've got a button styled like so: <input type="submit" id="btn" value="A submit button" class="red" /> I've also tried: <div class="red"> <input type="submit" id="btn" value="A submit button" /> </div> Neither work. When I remove the 'themes/base/jquery.ui.all.css' css file link the button's aren't styled at all. Crazy! I'm pulling my hair out. Where am I going wrong? Surely they should just make it easy enough to download JUST the theme folder and reference the ui.all file.

  Read the article

• Can't shrink Windows Boot NTFS disk: ERROR(5): Could not map attribute 0x80 in inode, Input/output error

  - by arcyqwerty

  Ubuntu 12.04 LTS, all updates current as of 7/3/2012 gksudo gparted Shrink /dev/sda2 from 367GB to 307GB GParted 0.11.0 --enable-libparted-dmraid Libparted 2.3 Shrink /dev/sda2 from 367.00 GiB to 307.00 GiB 00:32:57 ( ERROR ) calibrate /dev/sda2 00:00:00 ( SUCCESS ) path: /dev/sda2 start: 20,484,096 end: 790,142,975 size: 769,658,880 (367.00 GiB) check file system on /dev/sda2 for errors and (if possible) fix them 00:00:53 ( SUCCESS ) ntfsresize -P -i -f -v /dev/sda2 ntfsresize v2012.1.15AR.1 (libntfs-3g) Device name : /dev/sda2 NTFS volume version: 3.1 Cluster size : 4096 bytes Current volume size: 394065338880 bytes (394066 MB) Current device size: 394065346560 bytes (394066 MB) Checking for bad sectors ... Checking filesystem consistency ... Accounting clusters ... Space in use : 327950 MB (83.2%) Collecting resizing constraints ... Estimating smallest shrunken size supported ... File feature Last used at By inode $MFT : 389998 MB 0 Multi-Record : 394061 MB 386464 $MFTMirr : 314823 MB 1 Compressed : 394064 MB 1019521 Sparse : 330887 MB 752454 Ordinary : 393297 MB 706060 You might resize at 327949758464 bytes or 327950 MB (freeing 66116 MB). Please make a test run using both the -n and -s options before real resizing! shrink file system 00:32:04 ( ERROR ) run simulation 00:32:04 ( ERROR ) ntfsresize -P --force --force /dev/sda2 -s 329640837119 --no-action ntfsresize v2012.1.15AR.1 (libntfs-3g) Device name : /dev/sda2 NTFS volume version: 3.1 Cluster size : 4096 bytes Current volume size: 394065338880 bytes (394066 MB) Current device size: 394065346560 bytes (394066 MB) New volume size : 329640829440 bytes (329641 MB) Checking filesystem consistency ... Accounting clusters ... Space in use : 327950 MB (83.2%) Collecting resizing constraints ... Needed relocations : 13300525 (54479 MB) Schedule chkdsk for NTFS consistency check at Windows boot time ... Resetting $LogFile ... (this might take a while) Relocating needed data ... Updating $BadClust file ... Updating $Bitmap file ... ERROR(5): Could not map attribute 0x80 in inode 1667593: Input/output error ======================================== Windows has run chkdsk successfully (on boot) several times now

  Read the article

• What are the packages/libraries I should install before compiling Python from source?

  - by Lennart Regebro

  Once in a while I need to install a new Ubuntu (I used it both for desktop and servers) and I always forget a couple of libraries I should have installed before compiling, meaning I have to recompile, and it's getting annoying. So now I want to make a complete list of all library packages to install before compiling Python (and preferably how optional they are). This is the list I compiled with below help and by digging in setup.py. It is complete for Ubuntu 10.04 and 11.04 at least: build-essential (obviously) libz-dev (also pretty common and essential) libreadline-dev (or the Python prompt is crap) libncursesw5-dev libssl-dev libgdbm-dev libsqlite3-dev libbz2-dev More optional: tk-dev libdb-dev Ubuntu has no packages for v1.8.5 of the Berkeley database, nor (for obvious reasons) the Sun audio hardware, so the bsddb185 and sunaudiodev modules will still not be built on Ubuntu, but all other modules are built with the above packages installed. Python 2.5 and Python 2.6 also needs to have LDFLAGS set on Ubuntu 11.04 and later, to handle the new multi-arch layout: export LDFLAGS="-L/usr/lib/$(dpkg-architecture -qDEB_HOST_MULTIARCH)" For Python 2.6 and 2.7 you also need to explicitly enable SSL after running the ./configure script and before running make. In Modules/Setup there are lines like this: #SSL=/usr/local/ssl #_ssl _ssl.c \ # -DUSE_SSL -I$(SSL)/include -I$(SSL)/include/openssl \ # -L$(SSL)/lib -lssl -lcrypto Uncomment these lines and change the SSL variable to /usr: SSL=/usr _ssl _ssl.c \ -DUSE_SSL -I$(SSL)/include -I$(SSL)/include/openssl \ -L$(SSL)/lib -lssl -lcrypto Python 2.6 also needs Modules/_ssl.c modified to be used with OpenSSL 1.0, which is used in Ubuntu 11.10. At around line 300 you'll find this: else if (proto_version == PY_SSL_VERSION_SSL3) self->ctx = SSL_CTX_new(SSLv3_method()); /* Set up context */ else if (proto_version == PY_SSL_VERSION_SSL2) self->ctx = SSL_CTX_new(SSLv2_method()); /* Set up context */ else if (proto_version == PY_SSL_VERSION_SSL23) self->ctx = SSL_CTX_new(SSLv23_method()); /* Set up context */ Change that into: else if (proto_version == PY_SSL_VERSION_SSL3) self->ctx = SSL_CTX_new(SSLv3_method()); /* Set up context */ #ifndef OPENSSL_NO_SSL2 else if (proto_version == PY_SSL_VERSION_SSL2) self->ctx = SSL_CTX_new(SSLv2_method()); /* Set up context */ #endif else if (proto_version == PY_SSL_VERSION_SSL23) self->ctx = SSL_CTX_new(SSLv23_method()); /* Set up context */ This disables SSL_v2 support, which apparently is gone in OpenSSL1.0.

  Read the article

• Add Windows 7 to boot menu

  - by Cumatru

  Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS - system restore /dev/sda2 13 4674 37436416 7 HPFS/NTFS - Windows 7 /dev/sda3 4674 58843 435116032 7 HPFS/NTFS - data storage /dev/sda4 58843 60802 15728640 83 Linux - Ubuntu 10.10 Initially i´ve installed StartUpManager. This ( i think ) added another 4 instances of Linux + memtest to my boot menu list. Altough, i din´t see any boot menu. It boots into Ubuntu after a few seconds. I´ve tried to add windows 7, but i did not succeed. This is a part of my menu.lst file. title Ubuntu 10.10, kernel 2.6.35-24-generic uuid 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/vmlinuz-2.6.35-24-generic root=UUID=1c9748e2-2f11-4a6c-91c0-7310d48c4a7a ro quiet splash initrd /boot/initrd.img-2.6.35-24-generic title Chainload into GRUB 2 root 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/grub/core.img title Ubuntu 10.10, memtest86+ uuid 1c9748e2-2f11-4a6c-91c0-7310d48c4a7a kernel /boot/memtest86+.bin menuentry “Windows 7? { set root=(hd0,2) chainloader +1 } And this is after a upgrade-grub Searching for GRUB installation directory ... found: /boot/grub Searching for default file ... found: /boot/grub/default Testing for an existing GRUB menu.lst file ... found: /boot/grub/menu.lst Searching for splash image ... none found, skipping ... Found kernel: /boot/vmlinuz-2.6.35-24-generic Found kernel: /boot/vmlinuz-2.6.35-22-generic Found GRUB 2: /boot/grub/core.img Found kernel: /boot/memtest86+.bin Updating /boot/grub/menu.lst ... done Later Edit: Ive added the following in 40_custom from /etc/grub.d/ and ive decommented hidden menu line from menu.lst, but i still cant see any boot menu. Ive also tried to press ESC and SHIFT. menuentry "Windows 7 (loader) (on /dev/sda1)" { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda1)" { insmod part_msdos insmod ntfs set root='(hd0,msdos0)' chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,0) chainloader +1 } menuentry "!Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,1) chainloader +1 } menuentry "!!Windows 7 (loader) (on /dev/sda1)" { set root= hd(0,2) chainloader +1 }

  Read the article

• Ubuntu installation does not recognize drive partitioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• GParted in UBUNTU shows entire disk as UNALLOCATED SPACE

  - by msPeachy

  Good day to everyone. I hope someone can help me with my problem. I have a dual boot Windows and Ubuntu system. I recently encountered an hd0 out of disk error and wasn't able to boot Ubuntu. So I booted into Windows, after 2 to 3 times of booting and rebooting Windows, I tried booting Ubuntu but still I get the hd0 out of disk error. I decided to run Ubuntu from LIVEUSB to try to fix my Ubuntu partition using GParted, but when I run GParted, it shows my entire disk as UNALLOCATED SPACE! The strange thing is that Nautilus still shows and mounts my partitions. Also every time I boot into Windows , my partitions exists and I am able to read and write to them. I have no idea what is wrong. Please help! I can't stand using Windows since most of the tools I use are in Ubuntu. I don't mind reinstalling Ubuntu. In fact I already tried reinstalling using the LIVEUSB but I wasn't able to, since GParted or the Ubuntu installer itself does not recognized my partitions and shows the entire disk as unallocated space. I am currently running Ubuntu from LIVEUSB. Here's the outpuf of sudo fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb30ab30a Device Boot Start End Blocks Id System /dev/sda1 * 2048 104869887 52433920 83 Linux /dev/sda2 104869888 105074687 102400 7 HPFS/NTFS/exFAT /dev/sda3 105074688 156149759 25537536 7 HPFS/NTFS/exFAT /dev/sda4 156151800 625153409 234500805 f W95 Ext'd (LBA) /dev/sda5 156151808 169156591 6502392 82 Linux swap / Solaris /dev/sda6 169158656 294991871 62916608 7 HPFS/NTFS/exFAT /dev/sda7 294993920 471037944 88022012+ 7 HPFS/NTFS/exFAT /dev/sda8 471041928 625121152 77039612+ 7 HPFS/NTFS/exFAT When I run, sudo parted -l, I got this error message: ubuntu@ubuntu:~$ sudo parted -l Error: Can't have a partition outside the disk!

  Read the article

• Mounting an encrypted partion Error

  - by indiajoe

  Using the disk utilities in ubuntu 11.04, i had encrypted a partition with a passphrase. Each time i used to click on the partition to mount, it used to ask me the passphrase and get mounted. All was fine, until i installed the 12.04. After the installation, this encrypted partition, disappeared from the menu. fdisk -l /dev/sda Shows the encrypted partition in the list /dev/sda7 298953648 488392064 94719208+ 7 HPFS/NTFS/exFAT I tried the following commands to mount it. But they all gave following errors $ sudo cryptsetup luksDump /dev/sda7 Device /dev/sda7 is not a valid LUKS device. $ ecryptfs-unwrap-passphrase /dev/sda7 Passphrase: # i entered the correct passphrase here... Error: Unwrapping passphrase failed [-5] Info: Check the system log for more information from libecryptfs $ grep ecryptfs /var/log/syslog Oct 31 22:43:51 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading Nov 1 01:28:02 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading Nov 1 01:29:06 benny ecryptfs-unwrap-passphrase: Error attempting to open [/dev/sda7] for reading I don't understand why I am getting the "Device /dev/sda7 is not a valid LUKS device." Could it be due to some corruption in partition table? Is there any way to recover this encrypted partition? Thanks indiajoe

  Read the article

• Internal hard drive, can't format

  - by user113923

  I cannot format anymore the hard drive of my laptop. Here is how I proceed: I am starting my computer with a USB live drive (Ubuntu 10.04 LTS - the Lucid Lynx). Then I start disk utility and try to format the hard drive - I choosed to format the Master boot record but I get the following error: Error creating partition table: helper exited with exit code 1: Error calling fsync(2) on /dev/sda: Input/output error If I try to delete partitions I get the following error Error erasing: helper exited with exit code 1: In part_del_partition: device_file=/dev/sda, offset=32256 Entering MS-DOS parser (offset=0, size=30005821440) MSDOS_MAGIC found looking at part 0 (offset 32256, size 4096157184, type 0x83) new part entry looking at part 1 (offset 10618836480, size 8414461440, type 0x83) new part entry looking at part 2 (offset 19033297920, size 1077511680, type 0x82) new part entry looking at part 3 (offset 20110809600, size 9895011840, type 0x07) new part entry Exiting MS-DOS parser MSDOS partition table detected got it got disk got partition - part-type=0 Error: Input/output error during write on /dev/sda ped_disk_commit_to_dev() failed If I try to install ubuntu frrom the usb on the hard drive and choose erase and use the entire disk I get the error message Input/output error during write on /dev/sda For side infos I have at the moment 4 partitions on my hard drive: /dev/sda1 (ext2) /dev/sda2 (ext2) /dev/sda3 (swap) /dev/sda1 (ntfs) + /dev/sda (unlocated Space) My ultimate goal is to reinstall ubuntu and have only 2 partitions... I would really appreciate any help here! Thanks JB

  Read the article

• Ubuntu installation does not recognize drive partinioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Creating floppy drive special devices under Quantal

  - by JCCyC

  First, I'd like for the various special devices for different floppy capacities (like /dev/fd0u720 etc.) to be available. I tried to adapt some udev rules I found online. I tried this, which I saved as /etc/udev/rules.d/70-persistent-floppy.rules: # change floppy device ownership and permissions # default permissions are 640, which prevents group users from having write access # first fix primary devices (/dev/fd0, /dev/fd1, etc.) # also change group ownership from disk to floppy SUBSYSTEM=="block", KERNEL=="fd[0-9]*", GROUP="floppy", MODE="0660" # next recreate secondary devices (/dev/fd0u720, /dev/fd0u1440, etc.) SUBSYSTEM=="block", KERNEL=="fd[0-9]*", ACTION=="add", RUN+="create_floppy_devices -c -t $attr{cmos} -m %M -M 0660 -G floppy $root/%k" But to no avail. It seems the create_floppy_devices script isn't provided with 12.10. How do I obtain it? Second: I'm using MATE, and whenever I log in I get a message box saying it tried to mount the drive but failed. How do I disable this? Third (which is probably related to the second): Whenever there's a disk in the drive, the motor won't stop spinning. If I do a mdir of it, after it returns, the motor stops, and then starts again. I suspect there's some process in MATE doing this. UPDATE: For CentOS 6 (who does have a create_floppy_devices program) the following rules file worked. Saved as /etc/udev/rules.d/98-floppy.rules: # change floppy device ownership and permissions # default permissions are 640, which prevents group users from having write access # first fix primary devices (/dev/fd0, /dev/fd1, etc.) # also change group ownership from disk to floppy KERNEL=="fd[0-9]*", GROUP="floppy", MODE="0660" # next recreate secondary devices (/dev/fd0u720, /dev/fd0u1440, etc.) # drive A: is type 4 (1.44MB) - add other lines for other drives KERNEL=="fd0*", ACTION=="add", RUN+="/lib/udev/create_floppy_devices -c -t 4 -m %M -M 0660 -G floppy $root/%k"

  Read the article

• How to configure Logitech Marble trackball

  - by user27189

  You can configure it using xinput. I tested this in 11.10 and it works very nicely. This selection is from "Ubuntuwiki" Avoid using Hal for this release because it has known issues. Put the following into terminal, using gedit: Edit $HOME/bin/trackball.sh using this command: gedit $HOME/bin/trackball.sh Then paste this into the file: #!/bin/bash dev="Logitech USB Trackball" we="Evdev Wheel Emulation" xinput set-int-prop "$dev" "$we Button" 8 8 xinput set-int-prop "$dev" "$we" 8 1 # xinput set-int-prop "$dev" "$we" 8 1 # xinput set-int-prop "$dev" "$we Button" 8 9 # xinput set-int-prop "$dev" "$we X Axis" 8 6 7 # xinput set-int-prop "$dev" "$we Y Axis" 8 4 5 # xinput set-int-prop "$dev" "Drag Lock Buttons" 8 8 Make sure trackball.sh begins with #!/bin/bash. Make the script executable by running this: chmod +x $HOME/bin/trackball.sh` Add the following lines to $HOME/.bashrc, using gedit $HOME/.bashrc and put this in the file even if it is empty: xmodmap $HOME/.Xmodmap > /dev/null 2>&1 $HOME/bin/trackball.sh Edit $HOME/.Xmodmap using: gedit $HOME/.Xmodmap pointer = 1 8 3 4 5 6 7 9 Log out and back in and viola!

  Read the article

• Cryptswap boot error - can't mount?

  - by woody

  I believe i have my swap set up but am not sure because on start up it says that it is something along the lines of "could not mount /dev/mapper/cryptswap1 M for manual S for skip". But it appears to be mounted? I have already tried this solution with no success. When i run free -m the output is: total used free shared buffers cached Mem: 3887 769 3117 0 54 348 -/+ buffers/cache: 366 3520 Swap: 4026 0 4026 and sudo bklid is: /dev/sda1: UUID="9fb3ccd6-3732-4989-bfa4-e943a09f1153" TYPE="ext4" /dev/mapper/cryptswap1: UUID="bd9fe154-8621-48b3-95d2-ae5c91f373fd" TYPE="swap" and cat /etc/crypttab is: cryptswap1 /dev/sda5 /dev/urandom swap,cipher=aes-cbc-essiv:sha256 my /etc/fstab is: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=9fb3ccd6-3732-4989-bfa4-e943a09f1153 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation #UUID=bb0e378e-8742-435a-beda-ae7788a7c1b0 none swap sw 0 0 /dev/mapper/cryptswap1 none swap sw 0 0 cat /proc/swaps output is: Filename Type Size Used Priority /dev/dm-0 partition 4123644 0 -1 Is my swap not setup correctly or how can i fix my boot message?

  Read the article

• UDF Partition reported full when it is not

  - by Capt.Nemo

  I was using these instructions to setup an external hard disk with udf. I have been able to setup a multi-partition system using those instructions, but I seem to have hit a wall, where the partition is reported as full while writing to the disk. Every other tool available to me reports it as free. Relevant lshw output Here's a screenshot showing the disk: Both the output of df and the file manager (caja) report the disk as free. Filesystem Size Used Avail Use% Mounted on /dev/sda9 9.0G 7.6G 910M 90% / udev 974M 12K 974M 1% /dev /dev/sda1 50G 47G 295M 100% /media/Data /dev/sda6 49G 41G 5.9G 88% /home /dev/sda2 155G 127G 29G 82% /media/Entertainment /dev/sda8 14G 13G 516M 96% /media/Stuff /dev/sdb2 120G 1.9G 112G 2% /media/3c887659-5676-4946-875b-b797be508ce7 /dev/sdb3 11G 2.6G 7.7G 25% /media/108b0a1d-fd1a-4f38-b1c6-4ad1a20e34a3 /dev/sdb1 802G 34G 768G 5% /media/disk I seem to have hit a wall near the 35GB mark. Despite being shown as 35gb/860gb used everywhere, the following happens on a write attempt: [2017][/media/Dory]$ echo D>>echo bash: echo: write error: No space left on device Writing byte by byte, the maximum I can take it to is 34719248K. The most weird part is that on mounting it Windows, Windows can write to the disk easily, and the writes are being read fine back in Ubuntu. However, the used-bytes remains at 34719248K in Ubuntu (It goes higher on Windows, however).

  Read the article

• Banshee gapless playback does not work when playing mp3s

  - by ComputerGuy505

  Even though I have gapless playback enabled in Banshee's settings menu, there is a very short pause between songs. This might be due to the fact that my hard drive's partitions seem wierd. fdisk -l produces this output: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4a73c3cb Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 724153740 361872070+ 7 HPFS/NTFS/exFAT /dev/sda3 1456826368 1465145343 4159488 c W95 FAT32 (LBA) /dev/sda4 724154366 1456826367 366336001 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 1440159744 1456826367 8333312 82 Linux swap / Solaris /dev/sda6 724154368 1440159743 358002688 83 Linux Partition table entries are not in disk order Playing mp3's from /dev/sda2 or /dev/sda6 produces this problem. I don't seem to have gapless playback on Rhythmbox or Clementine either, if those media players are supposed to have it. I'm not sure what other info to provide. This is just annoying to me. Thanks for any help.

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• Dual Boot Windows 8 and Ubuntu

  - by Nick

  My laptop has two hard drives, one 320GB HDD and a 30GB SSD. I installed Windows 8 on the HDD and Ubuntu on the SSD. However, after I installed Ubuntu, Windows 8 did not appear on the boot list. I tried boot-repair, but this didn't help.Here is the output of my fdisk -l: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6cd9314a Device Boot Start End Blocks Id System /dev/sda1 * 2048 625139711 312568832 7 HPFS/NTFS/exFAT Disk /dev/sdb: 30.0 GB, 30016659456 bytes 255 heads, 63 sectors/track, 3649 cylinders, total 58626288 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6cd93132 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 207126 102539+ 83 Linux /dev/sdb2 208894 58626047 29208577 5 Extended /dev/sdb5 208896 4112383 1951744 82 Linux swap / Solaris /dev/sdb6 4114432 58626047 27255808 83 Linux Disk /dev/mmcblk0: 3965 MB, 3965190144 bytes 49 heads, 48 sectors/track, 3292 cylinders, total 7744512 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009c694 Device Boot Start End Blocks Id System /dev/mmcblk0p1 * 8192 7744511 3868160 b W95 FAT32 I also tried sudo grub-update, but that also did nothing.

  Read the article

• Grub not loading after Windows 8 Install

  - by RazorXsr

  My system was configured to dual boot Ubuntu 12.04.1 LTS and Windows 7. Today I got my hands on the MSDN release of Windows 8 and I installed it over my Windows 7. Now the computer just boots to Windows 8 directly without loading the GRUB screen. So I followed the steps as suggested in: https://help.ubuntu.com/community/RecoveringUbuntuAfterInstallingWindows. Running this command: ls -l /dev/disk/by-label/ gives the following output: total 0 lrwxrwxrwx 1 root root 10 Sep 11 07:51 Entertainment -> ../../sda2 lrwxrwxrwx 1 root root 10 Sep 11 02:45 PENDRIVE -> ../../sdb1 Also fdisk -l command gives this as the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1246aa23 Device Boot Start End Blocks Id System /dev/sda1 * 2048 319582199 159790076 7 HPFS/NTFS/exFAT /dev/sda2 319582208 602906623 141662208 7 HPFS/NTFS/exFAT /dev/sda3 602908672 625135615 11113472 83 Linux Disk /dev/sdb: 1939 MB, 1939865600 bytes 64 heads, 63 sectors/track, 939 cylinders, total 3788800 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdb1 * 2248 3788799 1893276 c W95 FAT32 (LBA) So I assume that I have to run this: sudo grub-install /dev/sda3 to get GRUB up and running. But I am getting this error: /usr/sbin/grub-probe: error: cannot find a device for /boot/grub (is /dev mounted?). Can anyone please guide me in the right direction? The current Ubuntu installation is far too customized to my needs to lose it to a boot manager issue! Any help is much appreciated!

  Read the article

• Two equal items in alternatives list

  - by Red Planet

  I want to have two JDKs. The first one was installed a long time ago to /usr/lib/jvm/java-7-oracle/. I installed the second version and executed following commands to add it to alternatives: red-planet@laptop:~$ sudo update-alternatives --install "/usr/bin/java" "java" "/opt/java_1.6.0_35/bin/java" 2 update-alternatives: using /opt/java_1.6.0_35/bin/java to provide /usr/bin/java (java) in auto mode. red-planet@laptop:~$ sudo update-alternatives --install "/usr/bin/javac" "javac" "/opt/java_1.6.0_35/bin/javac" 2 update-alternatives: using /opt/java_1.6.0_35/bin/javac to provide /usr/bin/javac (javac) in auto mode. red-planet@laptop:~$ sudo update-alternatives --install "/usr/bin/javaws" "javaws" "/opt/java_1.6.0_35/bin/javaws" 2 update-alternatives: using /opt/java_1.6.0_35/bin/javaws to provide /usr/bin/javaws (javaws) in auto mode. And configured: There are 2 choices for the alternative java (providing /usr/bin/java). Selection Path Priority Status ------------------------------------------------------------ * 0 /opt/java_1.6.0_35/bin/java 2 auto mode 1 /opt/java_1.6.0_35/bin/java 2 manual mode 2 /usr/lib/jvm/java-7-oracle/bin/java 1 manual mode Press enter to keep the current choice[*], or type selection number: Why do I have two equal items in the list?

  Read the article

• What applications can be used in a Red Hat/CentOS cluster?

  - by Sandra

  Hi, When I look at the Red Hat cluster manuals 1 2, they only explain how to install it but not what applications can use it. I am new to clusters, so I don't know these things =) Let's say I want to 3 node high performance cluster; What applications would work with it? Also, how does an application talk to the cluster? Does the application need to have been written to support clusters? Sandra

  Read the article

• Color drop down in Excel cell (with no text)? e.g. bgcolor = Red-Green-Amber-unknown

  - by adolf garlic

  I have an Excel sheet that I'm using to keep track of the status of certain things. I want to have a column which consists of cells containing a repeated drop down that allows you to select (as background) red amber green unknown I don't want any text in this cell, I just want a coloured block. Is this possible? I've tried playing around with data-validation-list (based on range containing all of said colours but to no avail)

  Read the article

• fsck on LVM snapshots

  - by Alpha01

  I'm trying to do some file system checks using LVM snapshots of our Logical Volumes to see if any of them have dirty file systems. The problem that I have is that our LVM only has one Volume Group with no available space. I was able to do fsck's on some of the logical volumes using a loopback file system. However my question is, is it possible to create a 200GB loopback file system, and saved it on the same partition/logical volume that I'll be taking a snapshot of? Is LVM smart enough to not take a snapshot copy of the actual snapshot? [root@server z]# vgdisplay --- Volume group --- VG Name Web2-Vol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 29 VG Access read/write VG Status resizable MAX LV 0 Cur LV 6 Open LV 6 Max PV 0 Cur PV 1 Act PV 1 VG Size 544.73 GB PE Size 4.00 MB Total PE 139450 Alloc PE / Size 139450 / 544.73 GB Free PE / Size 0 / 0 VG UUID BrVwNz-h1IO-ZETA-MeIf-1yq7-fHpn-fwMTcV [root@server z]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.7G 3.6G 5.6G 40% / /dev/sda1 251M 29M 210M 12% /boot /dev/mapper/Web2--Vol-var 12G 1.1G 11G 10% /var /dev/mapper/Web2--Vol-var--spool 12G 184M 12G 2% /var/spool /dev/mapper/Web2--Vol-var--lib--mysql 30G 15G 14G 52% /var/lib/mysql /dev/mapper/Web2--Vol-usr 13G 3.3G 8.9G 27% /usr /dev/mapper/Web2--Vol-z 468G 197G 267G 43% /z /dev/mapper/Web2--Vol-tmp 3.0G 76M 2.8G 3% /tmp tmpfs 7.9G 92K 7.9G 1% /dev/shm The logical volume in question is /dev/mapper/Web2--Vol-z. I'm afraid if I created the loopback file system in /dev/mapper/Web2--Vol-z and take a snapshot of it, the disk size will be trippled in size, thus running out of disk space available.

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >