Search Results

Search found 6432 results on 258 pages for 'wireless adapter'.

Page 43/258 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• Laptop loses signal from WiFi router, but mobile phone holds it fine

  - by Anton

  Hi, I have an extremely weird issue with my WiFi router. Both Ubuntu & Windows 7 can connect to it fine, but after 5-10 minutes browser (any one) stops opening pages and tells me it cannot resolve host address. But, at the same time, tools like Skype or BitTorrent work without any issues. I can also browse Internet on my mobile phone connected to the very same router. If I reset router it helps, but after 5-10 minutes I see just the same problem... Ubuntu tells me that WiFi signal is lost (mobile sees it), Windows 7 just won't let me browse anywhere. Can anyone give me a suggestion on this, please? Thanks

  Read the article

• Is it possible to impersonate another WAP by intercepting communication with other client?

  - by OSX NINJA

  There is a well known WAP that lots of people use. Someone comes in with a laptop equipped with a sniffer. The laptop sniffs people trying to log on to the WAP. It intercepts the connection, and when people try to log on to the WAP, they unknowingly log on through that person's laptop instead. All communication between the WAP and people's laptops go through that person's laptop. That person's laptop is able to block access to certain websites that the WAP would normally allow.

  Read the article

• My Laptop (HP/Compaq 2510p) running ubuntu 10.04 LTS keeps losing the WLAN connection.

  - by Ernelli

  I am using Wicd and can successfully connect to my ADSL router (Thomson TG 787) using WPA PSK. But with regular interval I lose the ability to connect to Internet. I can ping the GW and can actually ping servers on the Internet but not connect to them using HTTP (Tested with both Firefox and wget). I would suspect the router unless for the fact that the problem does not show up when running Windows XP on the same computer and also, when the problem arises, a simple disconnect/connect in Wicd solves the problem, which does not involve the router (Except for the DHCP request). I have searched Ubuntu forums without luck, most problems described relate to specific network drivers or other problems. Does anyone have the same experience with Linux/Ubuntu and WLAN?

  Read the article

• User for Public Network

  - by user71604

  my computer can catch the signal for many Access Points for the same network, while the network has problem with internet connection in some APs and it's working in others "all APs have the same SSID" Please advice if as i user i can force my computer to connect with specific AP neither than to go with the one with higher power (through MAC adress or IP)?. I am sure that my computer catch more than 10 signals for APs"All with same SSID". I am using windows 7 home primume 64 bit. as a user i dont have access to the AP config.

  Read the article

• Multiple wifi cards and Internet connections on Win-7

  - by Dpp

  Hello, I have two wifi cards and two separated internet connections. I connect to the Internet with both of them but one does all of the internet transactions (and I have not seen any place where I can specify which one I would prefer to use!) What I would like to do is use one of them for the browser and skype only, and the other one for stock exchange software for instance. Any idea if it is possible?

  Read the article

• Windows 7 - saved wifi access points disappear from list

  - by KáGé

  I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

  Read the article

• Is it safe to use an American power adapter in India and Australia?

  - by Stan

  I'm going to India and Australia on a business trip in a couple of days and plan to carry only a tablet instead of my trustworthy laptop (which got dunked in the tub by my oldest - don't ask). The adapter states the following: 100-240V~0.65A, 50/60Hz Output 12V===2A Will it be safe to use the adapter in these countries to charge my device, or do I have to buy new ones there? If the latter, what kind? What else should I take along with me? A surge protector?

  Read the article

• Does a HDMI-to-DVI (dual link) adapter exist? I don't care about the price

  - by alex k

  My monitor supports full-resolution display (2560x1440) only when connected to through either the DVI-D dual link port, or the DisplayPort. My laptop, though, has neither of these two kinds of output. Instead, all it's got is a HDMI port (which is version 1.3, and I also read that the laptop's graphics chipset supports 2560x1440 at 60Hz). So I'm wondering whether anyone has ever seen an HDMI-to-DVI dual link adapter, which will carry my ultra-highres signal to the monitor I just bought. So far I haven't seen any, and don't even know whether such an adapter (which I understand would have to be active, USB-powered and expensive (but I don't care)) exists.

  Read the article

• How to get Tenda W322U V2.0 Wireless adapter running on Windows 7?

  - by dircowander

  My Tenda W322U V2.0 Wireless USB Adapter used to work with Ralink drivers and I can't make it work on the new Windows 7. Every time the network adapter is booted, it keeps looking for a driver update and after updating, no wireless connection shows in the launcher in the panel. I was wondering whether the adaptor uses the Ralink chipset at all. Is there a version available with a wider choice of drivers?

  Read the article

• Why are there so few Wireless N Dual Band adapter PCI cards, only USB adapters instead?

  - by daiphoenix

  There has been several Wireless N Dual Band routers/APs out in the market for quite some time now, and there are several Wireless N Dual Band USB adapters out there. But as for PCI/PCI-X card adapters, there seems to be only one (the Linksys WMP600N). Why is that? I find it very strange. Is it because the USB adapters are easier to install, and can be used on multiple computers? But if so, why isn't it the same case with single band (2.4 Ghz) wireless N adapters? Because for these ones there as many PCI card adapters as there are USB adapters. Also, can the USB adapters, despite the lack of external antenna, offer the same level of performance as a card with external antennas?

  Read the article

• How to forward http traffic through a specific network adapter.

  - by user18129

  i have the following scenario. Two laptops are connected via a router through the Ethernet ports. These two computers need to be able to communicate together. One computer also needs to access the internet through a different adapter (i.e. we will taking these two laptops two various sites where by the most common type of internet access will be wireless).In isolation all of the various adapters work fine (i.e. the internal network works fine, and the wireless connects to the internet). However,we try to turn on all of the adapters at the same time,the following occurs: If we bridge the two network connections together on the "Server" -The internet connection doesn't work through the wireless If we don't bridge the connections The internet connections don't work It seems like http traffic is trying to be sent through the Ethernet adapter (which of course is not connected to an internet connection). How can we solve this?

  Read the article

• Why can't I connect to a Cisco wireless access point?

  - by spinlock

  I'm running a Lucid Netbook Remix on my Dell Inspiron 600m and I was not able to connect to the wireless network at the Hacker Dojo in Mountain View yesterday. There were plenty of other people on the network - MS, Mac, and Linux boxes - but my laptop would never get an ip address. I can connect to my home network, which is open, and I've never had a problem connecting at the coffee shop, which uses WPA. The Hacker Dojo is running WPA and we checked the password a number of times but got no love. Any ideas would be greatly appreciated. Additional Info: $iwlist eth1 scan eth1 Scan completed : Cell 01 - Address: EC:C8:82:FA:63:92 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:62 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 280ms ago Cell 02 - Address: 00:18:4D:24:08:61 ESSID:"Green Zone" Protocol:IEEE 802.11bg Mode:Master Frequency:2.417 GHz (Channel 2) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:23 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 11516ms ago Cell 03 - Address: 08:17:35:32:6E:13 ESSID:"\x00" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:71 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 2760ms ago Cell 04 - Address: EC:C8:82:FA:63:90 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:61 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 772ms ago Cell 05 - Address: 08:17:35:32:6E:11 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:65 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 3308ms ago Cell 06 - Address: 08:17:35:32:7E:31 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:88 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 1668ms ago Cell 07 - Address: 38:E7:D8:01:46:1E ESSID:"JWS_Incredible" Protocol:IEEE 802.11bg Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 500 kb/s; 54 Mb/s Quality:31 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Extra: Last beacon: 2848ms ago Cell 08 - Address: 08:17:35:32:6E:10 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:67 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 7848ms ago Cell 09 - Address: 08:17:35:32:7E:30 ESSID:"HackerDojo" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:85 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 8300ms ago Cell 10 - Address: 08:17:35:32:6E:12 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.437 GHz (Channel 6) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:68 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 232ms ago Cell 11 - Address: 08:17:35:32:7E:32 ESSID:"HackerDojo-gwifi" Protocol:IEEE 802.11g Mode:Master Frequency:2.462 GHz (Channel 11) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:86 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 168ms ago Cell 12 - Address: EC:C8:82:FA:63:91 ESSID:"HackerDojo-Presenter" Protocol:IEEE 802.11g Mode:Master Frequency:2.412 GHz (Channel 1) Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s 11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Quality:62 Signal level:0 Noise level:0 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Extra: Last beacon: 7408ms ago $iwconfig eth1 eth1 unassociated ESSID:"HackerDojo-gwifi" Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:16 dBm Retry short limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• Configuring WPA WiFi in Ubuntu 10.10

  - by sma

  Hello, I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

  Read the article

• Using JCA Adapter with OSB 11.1.1.3

  - by James Taylor

  In OSB 10g to use the JCA adapters you were required to use JDeveloper to create the necessary WSDLs and XSDs etc using the associated adapter wizard. These files were imported into Oracle Workshop (Eclipse) and used to create the business service as you would any other web service. In 11g unfortunately JDeveloper is still required. The process has changed slightly as described below. As an example I have used the JCA DB adapter as an example. Start JDeveloper 11.1.1.3 Create a new SOA Application Create a new SOA Project and call it DBAdapters. Choose the Empty Composite Template Drag a Database Adapter Component to the External References panel on the composite. Provide a service name. Create a new database connection, or use an existing one Take note of the JNDI Name, e.g. eis/DB/MyConnection This will be used to configure the DB connection in the WebLogic Console. In my example I use a stored procedure, but you can use what ever operation you require. Please refer to the following link for other options: User's Guide for Technology Adapters Select a schema and stored procedure Once the procedure has been selected, accept the defaults and finish. Startup your OEPE version of Eclipse. Create a new Oracle Service Bus Configuration Project (you can use an existing project if you have one) Create a new Oracle Service Bus Project in the configuration project created above. Instead of importing the WSDL and XSD files you import the jca file created in JDeveloper. In Eclipse right click the Oracle Service Bus Project and select Import –> Import    Choose File System Browse to the directory where JDeveloper stores its project Select the jca, wsdl, and xsd files based on the service you created in step 5. Also check the ‘Create selected folders only’ radio button. When you import you may have a little red x indicating the files are invalid. This is due to the location of the files. Open the invalid files and fix the path in relation to where you store your files in the OSB project.   Once you have the files all valid, Right-Click the jca file and select Oracle Service Bus –> Generate Service. This will create a new Business Service. In the WebLogic Console configure the JNDI name defined in step 7. You can now deploy your project and test

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Is proprietary vendor software required to use a wireless printer?

  - by sajee

  On Windows Vista, other than the driver, one can use a regular printer w/o any extra software, either plugged in via USB or over the network. I don't have to install extra software from the printer vendor to use the basic printer functionality. Is the same true for wireless printers? I need to install the HP 6000 wireless printer, and I hate installing vendor software other than the required drivers. So I'm wondering whether I need to install HP software on every PC that wants to use this printer? I haven't had a chance to read the manual but I'm hoping I don't have to. Can folks that have experience with wireless printers comment on whether vendor software, other than the printer driver, is required to use a wireless printer?

  Read the article

• Designing a Parallel-to-Serial Port Adapter

  A parallel-to-serial port adapter for bi-directional parallel-to-serial and serial-to-parallel data transfer Serial port - Programming - Components - Serial - Component Frameworks

  Read the article

• Using a DisplayLink USB video adapter on Ubuntu 12.10

  - by Jason R

  The line of USB video adapters made by DisplayLink has a somewhat sordid history under Linux. In past Ubuntu releases, the process of getting them to work has been somewhat difficult, inspiring a number of past questions on this site: example 1 example 2 example 3 However, there are some indications that version 3.5 of the Linux kernel (which is used by 12.10) contains better support for these adapters, which should make them easier to use. I currently have a single-GPU machine (it is an Nvidia adapter) with dual monitor outputs. I would like to add the DisplayLink adapter to drive a third external monitor. How can I set this up on Ubuntu 12.10?

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• mount old ATA disk to USB adapter

  - by 213441265152351

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic USB-IDE, an ATA adapter to USB 1.0 similar to the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. Any ideas?

  Read the article

• Can I use an Apple AirPort Express as a wireless-to-wired bridge?

  - by Chris

  I have a wireless network using an Apple AirPort Extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple AirPort Express's ethernet jack to create a wireless-to-wired bridge? If not, what device would I use to do the same thing?

  Read the article

• Laptop works fine with ac adapter, hangs after login screen using battery

  - by tavoton

  I did an Ubuntu 10.10 Desktop Edition clean install (amd64 version) on a notebook Medion Akoya E1311. With AC adapter everything works fine, but using battery, it hangs after login screen. I can type login, password too, and I can press login button. But then I can see mouse cursor and lower task bar, not upper, and nothing works. The only thing I can do is login on a terminal with ctrl+alt+F1, this is ok. Nothing seems alive on Gnome except mouse cursor. The only thing I did after Ubuntu fresh install was donwloading driver for RTL8191SE from Realtek web, because WiFi didn't work, now works fine, with ac adapter of course. Hardware is a Notebook Medion Akoya E1311 AMD Sempron 210U 1 GB DDR2 ATI RS690M (Radeon X1200 Series) Western Digital 160GB wireless RTL8191SEvB ethernet RTL8101E/RTL8102E

  Read the article

• wireless usb hub with the hub on the computer side - does this exist?

  - by Mala

  Hi I'm looking for what is effectively a wireless usb hub, but where the "hubbing" part takes place on the computer-side. In other words, something like this: http://www.iogear.com/product/GUWH104KIT/ Except rather than all four "terminating" slots being connected, having 4 small "wireless terminals" so that the devices can be placed all over a room instead of all within reach of the wireless usb hub Does such a product exist? Thanks!

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Why is my wireless so slow compared to my wired download speed?

  - by Shawn

  I just used speedtest.net (using Firefox) to compare my wired connection speed with my wireless connection speed. With my current contract (with Videotron), I'm supposed to get Download speed: 8Mbps Upload speed: 1Mbps Here are the results of the speedtest.net test: Wired Ping: 14ms Download speed: 8.41Mbps Upload speed: 1.04Mbps Wireless Ping: 16ms Download speed: 0.18Mbps Upload speed: 0.98Mbps The difference in download speeds seems staggering to me since I did the test 1 meter aways from my router. Any clue as to why my wireless download speed is so low compared to my wired download speed? using Ubuntu 11.04 on an Acer Aspire 5536-5519 Oh and it might be worth mentioning that my girlfriend has no trouble at all with her wireless connection. No slowness at all. (She uses Firefox on Windows 7 on a Dell) Here's the results for the same test on her system: Ping: 22ms Download speed; 8.44Mbps Upload speed: 1.02Mbps

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >