Search Results

Search found 14850 results on 594 pages for 'full decent'.

Page 431/594 | < Previous Page | 427 428 429 430 431 432 433 434 435 436 437 438  | Next Page >

• QoS basics on a Cisco ASA

  - by qbn

  Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

  Read the article

• How to easily input and display isolated japanese radicals on MacOS X?

  - by ogerard

  (This question was considered as off-topic on Japanese.SE and more suitable for SuperUser). I like to write computer notes about what I learn in Japanese. From time to time, I would like to be able to include in my text a given radical, say kokoro ?, which takes several graphic forms when used as an element in a more complex kanji, for instance . I did not succeed on my system (Mac OS X 10.7) to find the glyphs for these variants conveniently and exactly as I would like them (I would also be interested about how to do this on Windows 7 or Linux). I first tried the name of the kanji from which the radical is derived. Then I tried to use the japanese name for them, such as risshinben (as in ?) and shitagokoro (as in ?), hoping that the hiragana or katakana input would recognize them and propose me their representation, but it did not work. So I looked into the Full Japanese Character Table, under the "by radical" tab, and found at least a version of each of them : ? (CJK 5FC4) and ? (CJK 38FA) with the correct kun readings. I have them now as favorites but do I need to do that for all radicals? Do I need to register all of them in a user dictionary? I would imagine that I am not the only one who wants to do use them. Besides, the versions I have found are not suited for all occasions: they are centered on a standard kanji square. If I want them to appear near to a placeholder, or demonstrate their proportion to the rest of a typical kanji, I have to make complicated adjustments, depending on my use and the kind of radical. More generally are there computer tools for japanese dictionary editors and japanese teachers I could use on Mac OS X? (I could not add relevant tags such as : japanese or ideogram, please feel free to edit)

  Read the article

• Unexplained CPU and Disk activity spikes in SQL Server 2005

  - by Philip Goh

  Before I pose my question, please allow me to describe the situation. I have a database server, with a number of tables. Two of the biggest tables contain over 800k rows each. The majority of rows are less than 10k in size, though roughly 1 in 100 rows will be 1 MB but <4 MB. So out of the 1.6 million rows, about 16000 of them will be these large rows. The reason they are this big is because we're storing zip files binary blobs in the database, but I'm digressing. We have a service that runs constantly in the background, trimming 10 rows from each of these 2 tables. In the performance monitor graph above, these are the little bumps (red for CPU, green for disk queue). Once ever minute we get a large spike of CPU activity together with a jump in disk activity, indicated by the red arrow in the screenshot. I've run the SQL Server profiler, and there is nothing that jumps out as a candidate that would explain this spike. My suspicion is that this spike occurs when one of the large rows gets deleted. I've fed the results of the profiler into the tuning wizard, and I get no optimisation recommendations (i.e. I assume this means my database is indexed correctly for my current workload). I'm not overly worried as the server is coping fine in all circumstances, even under peak load. However, I would like to know if there is anything else I can do to find out what is causing this spike? Update: After investigating this some more, the CPU and disk usage spike was down to SQL server's automatic checkpoint. The database uses the simple recovery model, and this truncates the log file at each checkpoint. We can see this demonstrated in the following graph. As described on MSDN, the checkpoints will occur when the transaction log becomes 70% full and we are using the simple recovery model. This has been enlightening and I've definitely learned something!

  Read the article

• USB To Serial under OpenSuse 11.3

  - by Lars

  I have a LogiLink USB-To-Serial adapter. This has the PL2303 chip inside. When I insert the device: [26064.927083] usb 7-1: new full speed USB device using uhci_hcd and address 9 [26065.076090] usb 7-1: New USB device found, idVendor=067b, idProduct=2303 [26065.076099] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [26065.076105] usb 7-1: Product: USB-Serial Controller [26065.076110] usb 7-1: Manufacturer: Prolific Technology Inc. [26065.079181] pl2303 7-1:1.0: pl2303 converter detected [26065.091296] usb 7-1: pl2303 converter now attached to ttyUSB0 So the device is recognized and the converter is attached to ttyUSB0. When I do screen /dev/ttyUSB0 9600 I get the error: bash: /dev/ttyUSB0: Permission denied So I went looking in the file permissions. ls -l from the /dev folder reports: crw-rw---- 1 root dialout 188, 0 2011-04-26 15:47 ttyUSB0 I added my user lars to the dialout group. When I use the commands groups under lars it shows that I'm in the group. Though I still recieve the permissions denied error, as lars, and as root. I'm trying to connect to a console cable to configure some Cisco switches. My OS is OpenSuse 11.3 x86_64 with kernel version 2.6.34.7-0.7-desktop.

  Read the article

• Clamav. WARNING: No clamd server appears to be available

  - by Jevgeni Smirnov

  I have clamav.log full of these messages, what might be the problem and how to fix this? I have Debian clamav-0.97.6+dfsg-1~squeeze1 spamassassin-3.3.1-1 dovecot-pop3d-1.2.15-7 postfix-2.7.1-1+squeeze1 and also there is somewhere near milter. LocalSocket setting is ok Tue Jun 4 07:43:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:44:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:45:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:46:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:47:34 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:47:58 2013 -> ERROR: Failed to initiate streaming/fdpassing Tue Jun 4 07:47:58 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:48:58 2013 -> WARNING: No clamd server appears to be available Tue Jun 4 07:49:33 2013 -> ERROR: Failed to initiate streaming/fdpassing Tue Jun 4 07:49:33 2013 -> WARNING: No clamd server appears to be available

  Read the article

• Cannot cd to parent directory with cd dirname

  - by Sharjeel Sayed

  I have made a bash command which generates a one liner for restarting all Weblogic ( 8,9,10) instances on a server /usr/ucb/ps auwwx | grep weblogic | tr ' ' '\n' | grep security.policy | grep domain | awk -F'=' '{print $2}' | sed 's/weblogic.policy//' | sed 's/security\///' | sort | sed 's/^/cd /' | sed 's/$/ ; cd .. ; \/recycle_script_directory_path\/recycle/ ;' | tr '\n' ' ' To restart a Weblogic instance, the recycle ( /recycle_script_directory_path/recycle/) script needs to be initiated from within the domain directory as the recycle script pulls some application information from some .ini files in the domain directory. The following part of the script generates a line to cd to the parent directory of the app i.e. the domain directory sed 's/$/ ; cd .. ; \/recycle_script_directory\/recycle/ ;' | tr '\n' ' ' I am sure there is a better way to cd to the parent directory like cd dirname but every time i run the following cd command , it throws a "Variable syntax" error. cd $(dirname '/domain_directory_path/app_name') How do i incorporate the cd to the directory name in a better way ? Also are there any enhancements for my bash command Some info on my script 1) The following part lists out the weblogic instances running along with their full path /usr/ucb/ps auwwx | grep weblogic | tr ' ' '\n' | grep security.policy | grep domain | awk -F'=' '{print $2}' | sed 's/weblogic.policy//' | sed 's/security\///' | sort 2) The grep domain part is required since all domain names have domain as the suffix

  Read the article

• Troubles installing/starting Redis via Resque

  - by Craig Flannagan

  Trying to complete instructions for Resque/Redis installation here: https://github.com/defunkt/resque/blob/master/README.markdown Am stuck at where I'm trying to start up Redis via Resque at the following command: Craig:/usr/local/src/resque$ rake redis:start (in /usr/local/src/resque) Detach with Ctrl+\ Re-attach with rake redis:attach ../../bin/dtach -A /tmp/redis.dtach ../../bin/redis-server ../../../etc/redis.conf rake aborted! Command failed with status (127): [../../bin/dtach -A /tmp/redis.dtach ../../...] (See full trace by running task with --trace) Rerunning with --trace (showing only part of trace): Craig:/usr/local/src/resque$ rake redis:start --trace (in /usr/local/src/resque) ** Invoke redis:start (first_time) ** Execute redis:start Detach with Ctrl+\ Re-attach with rake redis:attach ../../bin/dtach -A /tmp/redis.dtach ../../bin/redis-server ../../../etc/redis.conf rake aborted! Command failed with status (127): [../../bin/dtach -A /tmp/redis.dtach ../../...] /Users/craigflannagan/.rvm/gems/ruby-1.9.2-head@foo/gems/rake-0.8.7/lib/rake.rb:995:in `block in sh' Not sure what is wrong here - by the way, when I did those instructions $ git clone git://github.com/defunkt/resque.git $ cd resque $ PREFIX=<your_prefix> rake redis:install dtach:install $ rake redis:start I wasn't sure whether or not I was supposed to be doing #1 from within the Rails project, or if I was supposed to have the git clone create a new folder outside the Rails project (in this case, I chose to have folder created outside the project).

  Read the article

• Vista logs into black screen, "Application Error 0xc0000022" for explorer.exe

  - by IMAPC

  Whenever I attempt to log into a Windows Vista computer (the only account on it), I'm presented with a black screen & a cursor. I can open Task Manager, and from there I can launch applications. It seems to be using Aero Basic (instead of the full Aero which I had set as default before the problem started). When attempting to launch "explorer.exe" I get "explorer.exe - Application Error 'The application failed to initialize properly (0xc0000022). Click OK to terminate the application.'" Every now and then I get an error along the lines of "the application has failed to start because its side by side configuration is incorrect please see the application event log for more detail." I can boot into safe mode successfully, but I still get the black screen when I log into it in regular mode. I've tried most of the suggestions here, but did not work. I'm attempting to back up everything right now in case the only fix is to reinstall Windows. Has anyone seen this before?

  Read the article

• cPanel web servers mounting home partition to a NAS or SAN

  - by Scott

  Hello, I currently have 2 cPanel web servers that are little 1RU dual cpu quad core xeons. They have a lot of resources for processing and handling web requests, and never exceed more than 10% cpu usage. They also have plenty of RAM. The problem is though that they both have RAID 1 160Gb SAS hard disk drives in them that are 75% full, and growing by the day. I didnt think that the amount of disk usage would be so high, but due to the nature of the sites hosted, this has become an issue. The easy fix would be just to upgrade the hard drives to something bigger (probably not of the SAS variety), but I am thinking of keeping the current machines as "processing servers" and buying a central "storage server" with about 12TB of storage. The /home/ partition on each of the 1RU servers would be mounted to a NAS or SAN point on this central storage server. My questions are: - Has anyone got a cPanel setup where they mount /home/ to a NAS or SAN elsewhere? If so, can you provide details as to what you did and how it went :) - Any recommendations on networking? Is gigabit ethernet enough? Is TCP/IP going to be a noticable performance problem? Anyone used a TOE key? - Anyone benchmarked or had any performance issues with SAN over NAS? Any help greatly appreciated. Scott

  Read the article

• Where to get glib-config for Kubuntu?

  - by Carl Smotricz

  I'm trying to compile Midnight Commander on a KUbuntu 9.10 (Karmic) box with no root access. I've set up a directory under $HOME, downloaded the mc source package and various stuff required for building, such as autotools. I've unpacked the CONTENTS of all those packages into this working directory such that I have the usual ./usr, ./lib, ./etc hierarchy. I manage to get configure through a lot of tests, but I can't seem to fool it into finding glib. checking for glib-2.0... checking for glib-config... no checking for glib12-config... no checking for glib-config... no checking for GLIB - version >= 1.2.6... no *** The glib-config script installed by GLIB could not be found *** If GLIB was installed in PREFIX, make sure PREFIX/bin is in *** your path, or set the GLIB_CONFIG environment variable to the *** full path to glib-config. configure: error: Test for glib failed. GNU Midnight Commander requires glib 1.2.6 or above. My system has glib installed: /lib/libglib-2.0.so.0 /lib/libglib-2.0.so.0.2200.3 ... and I've also downloaded and unpacked the glib package into my working directory: libglib2.0-0_2.22.2-0ubuntu1_i386.deb libglib2.0-dev_2.22.2-0ubuntu1_i386.deb ... but still the elusive glib-config is nowhere to be found. It's not in any debian package for Karmic, either. So I'd appreciate any help getting over this hurdle. Please note, again, that I don't have root, so I can't just merrily apt-get stuff.

  Read the article

• Could not continue scan with NOLOCK due to data movement during installation

  - by dbdev1

  Hi, I am running Windows Server 2008 Standard Edition R2 x64 and I installed SQL Server 2008 Developer Edition. All of the preliminary checks run fine (Apart from a warning about Windows Firewall and opening ports which is unrelated to this and shouldn't be an issue - I can open those ports). Half way through the actual installation, I get a popup with this error: Could not continue scan with NOLOCK due to data movement. The installation still runs to completion when I press ok. However, at the end, it states that the following services "failed": database engine services sql server replication full-text search reporting services How do I know if this actually means that anything from my installation (which is on a clean Windows Server setup - nothing else on there, no previous SQL Servers, no upgrades, etc) is missing? I know from my programming experience that locks are for concurrency control and the Microsoft help on this issue points to changing my query's lock/transactions in a certain way to fix the issue. But I am not touching any queries? Also, now that I have installed the app, when I login, I keep getting this message: TITLE: Connect to Server Cannot connect to MSSQLSERVER. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 67) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=67&LinkId=20476 BUTTONS: OK I went into the Configuration Manager and enabled named pipes and restarted the service (this is something I have done before as this message is common and not serious). I have disabled Windows Firewall temporarily. I have checked the instance name against the error logs. Please advise on both of these errors. I think these two errors are related. Thanks

  Read the article

• windows 8.1 upgrade fails with error code 0xc1900101-0x20017

  - by cmorse

  I just tried to install windows 8.1 on my laptop, but it fails to install with the message: Sorry we couldn't complete the update to Windows 8.1. We restored your previous version of Windows to this PC 0xC1900101 - 0x20017 It looks like on the first boot that the laptop is going to the PC restore screen (it asks what kind of keyboard I have, and then what repair optins I would like to take). Thus far I have just been selecting "Continue to windows 8." I'm running a Lenovo x220i tablet. I've got 43GB of free disk space. It installed just fine on my desktop. The primary difference between the two machines is that the desktop has media center install, and isn't using TrueCrypt. Full WindowsUpdate.log http://pastebin.com/hGmAW4Q1 Most important portion of WindowsUpdate.log: 2013-10-17 10:41:06:671 964 694 Agent ************* 2013-10-17 10:41:06:671 964 694 Agent ** START ** Agent: Finding updates [CallerId = AutomaticUpdates] 2013-10-17 10:41:06:671 964 694 Agent ********* 2013-10-17 10:41:06:671 964 694 Agent * Online = No; Ignore download priority = No 2013-10-17 10:41:06:671 964 694 Agent * Criteria = "IsInstalled=0 and DeploymentAction='Installation' or IsPresent=1 and DeploymentAction='Uninstallation' or IsInstalled=1 and DeploymentAction='Installation' and RebootRequired=1 or IsInstalled=0 and DeploymentAction='Uninstallation' and RebootRequired=1" 2013-10-17 10:41:06:671 964 694 Agent * ServiceID = {7971F918-A847-4430-9279-4A52D1EFE18D} Third party service 2013-10-17 10:41:06:671 964 694 Agent * Search Scope = {Machine & All Users} 2013-10-17 10:41:06:671 964 694 Agent * Caller SID for Applicability: S-1-5-18 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {AD47FBDC-F7F9-4E7F-BAF4-DBA3784C7101} 2013-10-17 10:41:06:436-0600 1 202 [AU_REBOOT_COMPLETED] 102 {00000000-0000-0000-0000-000000000000} 0 0 AutomaticUpdates Success Content Install Reboot completed. 2013-10-17 10:41:07:233 964 870 Report REPORT EVENT: {8D4E7A67-9526-4702-A897-5BE5F97497AF} 2013-10-17 10:41:06:639-0600 1 204 [AGENT_INSTALLING_FAILED_POST_REBOOT] 101 {8951E70D-4332-4F7C-B92D-D9362E384959} 1 c1900101 WSAcquisition Failure Content Install Installation Failure Post Reboot. 2013-10-17 10:41:07:249 964 870 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2013-10-17 10:41:07:249 964 870 Report WER Report sent: 7.8.9200.16715 0xc1900101(0x20017) 8951E70D-4332-4F7C-B92D-D9362E384959 Install 101 Unmanaged 2013-10-17 10:41:07:249 964 870 Report CWERReporter finishing event handling. (00000000)

  Read the article

• Redmine subversion won't ignore certificate error even if told

  - by Pekka

  I have set up a copy of Redmine through the Bitnami Redmine Stack and am having trouble accessing a remote SVN repository through https. The trouble seems to be related to the fact that I don't have a signed certificate, and the certificate provided doesn't match the host name (I am accessing the same server through a number of host names). I am new to Ruby, Mongrel, Rails and Redmine. Following the advice in this forum thread, I changed the path Redmine uses to invoke the svn client in \apps\redmine\lib\ redmine\scm\adapters\subversion_adapter.rb from SVN_BIN = "svn" to SVN_BIN = "svn --trust-server-cert --non-interactive --config-dir c:/user/temp" I was hoping that the --trust-server-cert option would fix the certificate problem. However, I am still getting the following error message in mongrel.log: svn: OPTIONS of 'https://server.xyz:8443/svn/reponame': Server certificate verification failed: certificate issued for a different hostname, issuer is not trusted (https://server.xyz:8443) Does anybody know what to do about this? Additional info: I re-started the mongrel service after each change I am sure the configuration change has taken effect because subversion has created a full configuration directory in c:\user\temp I can access the remote repository using command line svn no problem The remote repository runs on a Windows box with VisualSVN

  Read the article

• Blank Icon in Control Panel?

  - by Wesley

  Hi all, Just recently I opened my Control Panel and saw that a blank icon came up before my list of icons. Has anyone else experienced this before? Would it be safe to delete it? Thanks in advance. EDIT: Oops, I should have mentioned this too, but when I try creating a shortcut on the desktop, I get a dialog box saying "Windows could not create the shortcut. Check if the disk is full." Clearly it isn't, since I still have 102 GB of free hard disk space... any ideas? EDIT2: Here is a screenie of my complete Control Panel: EDIT3: *So I did a manual search for .CPL in Windows Search and then looked at the list in TweakUI and got 3 unmatched .CPL files. They are [ncpa.CPL], [sapi.CPL], and [QuickTime.CPL]. I clearly know the QuickTime one, but not too sure about the rest. SCRATCH THAT, I FIGURED IT OUT... BUT IT'S NOT THE BLANK ICON.

  Read the article

• ip-up does not trigger when using built-in cisco vpn on mac osx lion

  - by Yasser Sobhdel

  I am using Cisco VPN client over lion and I want to make the ip-up and ip-down work. There is no sign of any action taken when I connect or disconnect this VPN connection. I really doubt whether the syntax has been changed or even this kind if connection is triggering the ip-up. Logically, it must be set over ppp but when using the following codes and instructions on them, there is no sign of any output in the log file: http://www.macfreek.nl/mindmaster/Modify_PPTP_Routing_Table http://www.aidanfindlater.com/use-vpn-for-specific-sites-on-mac-os-x Going for error, which there is no sign of it, using the following page: http://hints.macworld.com/article.php?story=20060616150640529 I couldn't find the /var/log/ppp/vpnd.log log file. Also the files are given full permission 0755 or a+x or even 777 using the following command: sudo chmod a+x /etc/ppp/ip-up Any clue on how to debug this would be appreciated. I am totally confused, netstat -rn -f inet doesn't show the routes. Even when the routes are added manually, closing the VPN connection does not run the ip-down and the routes must be deleted manually.

  Read the article

• How to permanently "renice" a process on Mac OS X (or iOS, etc)?

  - by mralexgray

  I use a nice (free) process manager called ATMonitor for Mac OS X that has a lot of cool hidden features... one of which is being able to click on a running process.. and set the "renice" from +20 (less priority) to -20 (highest priority). The best part.... it sticks between restarts... SO you want XYZ to get full attention all the time.. you set it once and it's done... I want to do the same thing (renice a process) on an iPad running a particular daemon.. and I don't know how to set a renice permanently. I can do it once, and it works fine... But the setting is lost on a reboot. I read somewhere.. Now, as for permanently resetting the priority of a process, this can't be done directly. You can fake it, however, with a shell script that starts the app and then immediately renice's it. Give that script a ".command" extension and it will be double-clickable in the GUI. Not very elegant, but it gets the job done. But as it says.. not very elegant, and I dont think this is how ATMonitor does it.... I found this thread.... http://superuser.com and they gave a way to do it as a launch argument, but no apparent way to save it as a persistent value... for instance - if the program wasn't going to be started by launchd... How do I set a permanent renice level, per executable binary, independent of it's PID, when, how or why it was launched?

  Read the article

• How to auto-mount encfs volume on login in ubuntu 9.10

  - by xzenox

  Hi, Previously, in 9.04, I was using pam mount in conjunction with encfs to mount an encrypted volume at login. This worked perfectly and since the password was the same as my user password, none was entered besides the initial login one. Now in 9.10, using the same setup and the same volume line in pam's config file, the volume will not mount. The folder does not even get created for the mount point. I am thinking this might be caused by the fact that I now switched to using an encrypted /home directory (previously left unencrypted on 9.04). To encrypt it, i used the standard /home encrypt setup from the 9.10 fresh install. I am thinking that perhaps, pam tries to mount the volume before /home is mounted and fails. Is there a log file I could look into/post here? Note that mounting manually works fine using the same paths, writing full paths does not help, nor is removing the options attribute. Here's my volume entry: <volume user="nicholas" fstype="fuse" path="encfs#~/.dropbox_dir/Dropbox/encrypted" mountpoint="~/Dropbox" options="nonempty" />

  Read the article

• How do Opera's keyboard shortcut settings work?

  - by zem

  Firefox 4 beta is starting to freeze up the way Firefox 3 used to on my machine, and I want a browser that'll play gifs at full speed, so on a Mac my only other choice seems to be Opera. There are just two issues I have with it right now: one, the scrolling is weird compared to every other Mac application, but I can get used to that if there's no way to fix it. Two, cmd-1 through cmd-9 activate the "speed dial" bookmarks instead of selecting tabs 1-9, like in Firefox and Chrome. I can disable those shortcuts easily enough, so I don't keep accidentally loading a different page when I instinctively try to do that, but in an ideal world I could remap those commands to do what I want. The keyboard shortcut editor is weird: There seems to be a scrappy little language for associating actions with commands. It has some limited autocompletion when you type stuff in, and I couldn't find a "select specific tab" action, but some of the existing commands are complicated enough that I'd be surprised if there's not a way to do it. Is there documentation for this language anywhere? Clicking "help" just brings me to this page, which is not very helpful.

  Read the article

• Exchange 2007 restore - Backup Exec Unable to Attach to a resource

  - by Andy

  I have been struggling with this one for months! Grateful for any advice. The setup is a windows 2003 server network, 4xservers on the domain. Two exchange 2007 servers (only one with mailboxes still on). Backup Exec (12.5) on a non-exchange server with agents on the others. Backup exec runs a full backup of exchange across the network well, at pretty reasonable speeds. However, when you try any kind of restore (individual emails, mailboxes or whole system restore - all to same location or to alternate server, RSG etc) the following message is received within about 10-15 secs of starting the job: Job ended: 24 December 2010 at 13:28:32 Completed status: Failed Final error: 0xe000848c - Unable to attach to a resource. Make sure that all selected resources exist and are online, and then try again. If the server or resource no longer exists, remove it from the selection list. Edit the selection list properties, click the View Selection Details tab, and then remove the resource. Final error category: Resource Errors For additional information regarding this error refer to link V-79-57344-33932 Things I have already tried: Changed account to main administrator account (with all permissions) checked versions of ese.dll on both servers - both the same Checked all VSS writers on both servers are stable / normal restoring to different locations Any advice anyone could give would be much appreciated. Many thanks, Andy

  Read the article

• IPMI not fucntioning with Network Bonding

  - by muhammed sameer

  Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

  Read the article

• IPCop server slows down download speed

  - by noocyte

  I have an IPCop server running at home, been doing just fine for ~5 months, but last week I suddenly started getting time-outs and slow downloads from the 'net. I first thought that this was my ISP acting up, then I thought it might be one of my 3 switches or some of my cabling. In due order I've tested everything above and found them all to be working as they should. The only factor remaining is my IPCop server. Facts: I've got a 15/15 Mbit line (fiber) and I get ~15 Mbit upload, but only 0.5 Mbit download with the IPCop box as router (ISP router set in bridge mode). If I connect without the IPCop box (using the ISP router) I get ~12 Mbit upload and ~15 Mbit download. The load on the IPCop box appears to be light and it used to handle this traffic just fine 2 weeks ago. The memory usage is ~60%, I tried to restart it and test again, the memory fell to ~50% then (5 months of uptime). I'm thinking that one of my nics are busted, but I'm sort of perplexed that this could be the outcome; slow download but full speed upload. Anybody ever seen that happening before? Could it just be one of the nics that needs to be replaced? Will try that as soon as I can get my hands on a couple of new ones.

  Read the article

• Windows or Linux for VPN-VPN Bridge

  - by James

  I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

  Read the article

• VMware Fusion configuration files missing

  - by jdmuys

  I need to set up port forwarding to my VM in Fusion 5. Everywhere on the net, the solution is described as editing the file: /Library/Application Support/VMware Fusion/vmnet8/nat.conf However, on my install, that file doesn't exist. Neither does the vmnet8 directory. Here is the full content of VMware stuff I have in /Library/Application Support/: /Library/Application Support/ VMware/ VMware Fusion AdminWritable Shared vmInventory usbarb.rules VMware Fusion That's right: /Library/Application Support/VMware Fusion/ exists but is empty. And there is no VMware folder in other Library directories on my system. I am running OS X 10.8.2. I just reinstalled Fusion 5.02, no change. Meanwhile, I have 3 VMs that work just fine. So how am I supposed to set up port forwarding with Fusion 5? Thanks, JD Edit: in a hunch, I tried ps ax | grep natd which returned: 9646 ?? S 0:00.01 /Applications/VMware Fusion.app/Contents/Library/vmnet-natd -s 7 -m /Library/Preferences/VMware Fusion/vmnet8/nat.mac -c /Library/Preferences/VMware Fusion/vmnet8/nat.conf So it seems that the configurations files are now in the directory /Library/Preferences/VMware Fusion. I'll work from here and edit this question as I make progress.

  Read the article

• Open Source PDF reader for windows as an alternative to Adobe reader

  - by Tom Feiner

  With the latest javascript vulnerabilities in Adobe reader and bloat it has aquired over the years, I've been thinking of moving the network I'm in charge of to a different product for PDF reading on Windows. The ideal PDF reader should be something that is: Small in size (Adobe reader is more than 200MB these days after installation). As secure by default as possible (For example, javascript disabled by default). Nice looking and easy to use interface. Not bloated with features (I just want to read PDFs, that's it). Does not install any toolbars/unwanted add ons/spyware. Does not display any ads while viewing PDFs. Preferably Open Source. (this pretty much ensures no ads). Full Unicode support. Idealy , something like evince from gnome, will be the best option, but unfortunately that's not available on Windows. Foxit is an option, as it is small, and has a nice interface. But it still has javascript enabled by default which might lead to vulnerabilities - and it installs a toolbar , and displays ads while reading PDFs which is distracting. There is a site dedicated to Open Source PDF readers, pdfreaders.org, however, the Windows pdf readers each have their problems, mostly the interface is not as convenient (as evince, adobe or foxit). Here's a list of all PDF software from WikiPedia. There's a "Viewers" section for each OS. What Windows PDF reader would you recommend ?

  Read the article

• Crash dump analysis

  - by Ryan Ries

  I hope this isn't a stupid question, and if it is, then I want to at least get it over with so I don't feel so dumb in the future. Here we are, loading up a Windows crash dump with Windbg. Here are the first few lines of the debugger output: 0: kd> .dumpdebug ----- 64 bit Kernel Summary Dump Analysis DUMP_HEADER64: MajorVersion 0000000f MinorVersion 00001db1 ... The MinorVersion I mostly understand. It's hexadecimal and it translates to 7601 in decimal. Windows admins would already be able to tell from that that this must be either a Win7 x64 machine or a 2k8 R2 machine with SP1. But isn't 7601 the build number? It's supposed to be Major.Minor.Build/Revision... right? Also I don't understand the MajorVersion. It should be 6. This version of Windows is 6. But isn't 0000000f in hexadecimal 15 in decimal? The full version string of this version of Windows, when you launch the Command Prompt for instance, is 6.1.7601. If 7601 is the MinorVersion, then what is 1 and what is 6? And why does the crash dump say 0F?

  Read the article

< Previous Page | 427 428 429 430 431 432 433 434 435 436 437 438  | Next Page >