Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 433/761 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

  • SSH into Ubuntu Linux on a box without a static IP address

    - by Steven Xu
    Basically, how do I do it? I'd like to connect to my home computer from work, but my internet is routed through my apartment building's network, so I don't have the static IP address I'm accustomed to having. How do I go about accessing my home computer through SSH (I'll be using Putty at work if it matters) if my home computer doesn't have a static IP address?

    Read the article

  • MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

    - by user88114
    This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

    Read the article

  • where to put core services in two-node cluster

    - by Veniamin
    I'm currently configuring two-node HA cluster based on CentOS with DRBD. Most services are packed in virtual machines with migration available. I have not made decision where to put some core services as: dhcp, ldap, dns - which are critical for all network infrastructure. There are two possibilities: Configure them as redundant HA services on cluster hosts. Pack them all into dedicated virtual machine. What is the best practice?

    Read the article

  • Resolve linux hostname in windows

    - by Martin Giffy D'Souza
    Hi, I have a simple home network with Windows 7 machines and Linux machines (Fedora 12 and 13). I'd like to be able to resolve the Linux machine names from the windows machine. For example: -- Windows 7 ping mylinuxmachine Currently this does not resolve. Any ideas? Thank you, Martin

    Read the article

  • Restart browser on error

    - by billfredtom
    Is there a way to restart a browser (Internet Explorer, Firefox, etc) automatically upon receiving an error such as a DNS error or Page not found? Background: It is for a web based signage application that has intermittent network drop outs, therefore if there's no internet, and the sign tries to go to the next page, an error occurs on browser, and we get one big ugly sign. We need a way to either restart the browser, or customise displayed error messages to use javascript to try redirection to the live sign again.

    Read the article

  • What is SIP trunking?

    - by hypnocode
    Can someone explain to me in plain English what SIP trunking is, please? I've read about it on Google, but I don't really grasp it yet. Does it allow a VoIP call to be placed outside of the LAN? So if you had Asterisk setup as the PBX, then IP calls could be made outside of the network? Am I close or am I just saying stupid words?

    Read the article

  • Record everything on command line centos /fedora/ ubuntu

    - by neolix
    Hello all, we are 100% Linux user across the network and we do work round clock, what happens shift change next admin come to his shift on that time what all issues comes he get resolve the issues but they just clear history from terminal. If we want record every at terminal what they have done to resolve the same issues or we can monitor as well, for trouble ticket we have internal OTRS which they update for reporting. Thanks ton

    Read the article

  • Windows 7 Administrator HomeUsers Account

    - by Charles Carrington
    I'm trying to login to my Windows 7 PC from another PC so that I can transfer files to the Windows 7 PC. I've just installed Visual Studio 2008 on my new PC, and I wan't to transfer all of my work from my old machine to my new one. When I first set up a user on the Windows 7 PC after a reformat, the account created had a Group field that read "HomeUsers; Administrators" when viewing it from the User Accounts screen. You get to this screen by typing "netplwiz" in the search field of the Start Menu. I changed the Group of this account to Administrators before I realized that it was assigned to two Groups -- "HomeUsers; Administrators" as I mentioned above. I was trying to make sure that it was an Administrator account so I didn't have to type in a password everytime I wanted to install software. I can use this computer normally without being asked for an administrator password all the time when I want to install new software, but I can't log in to this PC from another PC because I don't have an account that has a Group of "HomeUsers". I should have left the account alone; everything would've been fine. But there doesn't seem to be a way to assign it to two groups after the initial assignment that take place automatically when you are setting up your computer for the first time. If you assign "HomeUsers" to the account, the Group field on the User Accounts screen will just read "HomeUsers". If you assign "Administrators" to the account, the Group field on the User Accounts screen will just read "Administrators". There's no way to make it read "HomeUsers; Administrators" again. If you don't have at least one account that is a "HomeUsers" account, you cannot log in to the PC from another PC on the network. If you don't have an account that is an "Administrators" account, you cannot install software on your machine without being asked for an Administrator password all the time, which is very annoying. I want an account on my Windows 7 PC that I can use to install software without being asked for a password AND that I can log into from another PC on the network to transfer files. If I could make the Group field read "HomeUsers; Administrators" of my primary account on the Windows 7 PC when I go to the User Accounts screen by typing "netplwiz" in the search field of the Start Menu, my primary account would do what I want it to do. Does anybody know how to make an account in Windows 7 a "HomeUsers" account AND an "Administrators" account? As I said before, Windows 7 does this for you automatically when you first set up your computer. But if you change it inadvertently, there is no way to change it back. At least I don't know how to do it. If anybody has any ideas on how to fix this, I would greatly appreciate it. Thanks, Charles Carrington

    Read the article

  • wireless problem: Internet slow connection or limited connectivity

    - by jack
    Hi I have no idea on this problem. My wireless connection doesn't work sometimes. I find it's due to my XP and I have no problem with my Win 7 machine. The problem is - Internet Connection a bit slower than usual Limit connectivity issue I use netsh reset for resetting network configurations but it helps sometimes or not help at all. Any ideas? Thank you.

    Read the article

  • Some users cannot connect to Exchange Server or Outlook Web Access

    - by crn
    0 In our network, some users cannot connect to either Exchange Server 2007 or Outlook Web Access while others are able to connect to both. On one computer, the error occurred after the user ran the AVG anti-virus update. Some computers return this error message "Task 'Microsoft Exchange Server' reported error (0x800401 ID): The server is not available." Thanks, in advance, for your help!

    Read the article

  • Forwarding all received mail to another server in Exchange 2007

    - by Moo
    Hi, We are moving away from our Exchange environment on a hosted server to one managed in-house, and I was wondering how to have the hosted Exchange forward all email received to the new server - the servers are not on the same network, and both have the same users setup. Basically, I just need the hosted Exchange to act as a dumb relay - accept the mail, send it straight on to our new server without trying to deliver locally. Is this possible? Regards Moo

    Read the article

  • Routing protocols, distance vector vs link state

    - by Artem Barger
    I'm trying to figure out the differences(pros/cons) between two routing protocols approach and I would be great-full for any help, advice and explanation. As far I can say that it seems like distance vector is more static and more local based routing, since it doesn't know the network state whereas link state is more aware of current states therefore it seems more natural to use it over distance-vector, but I have a feeling like I'm missing something. And I would be glad to here about more aspects and different issues I have to consider while choosing one of them.

    Read the article

  • Routing RFC1918 addresses through dd-wrt via a switch

    - by espenfjo
    I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

    Read the article

  • Why can't Win7 remember my tether? New Connection Setup every time

    - by Andrew Heath
    In Win7 when you connect to a new network you're prompted to set it as a Home, Work, or Public connection. Presumably this influences default security settings. That's all well and good, except for the part that everytime I USB tether my smartphone Win7 comes up with a new dialogue. I think I'm up to generic connection 25 or something? It's getting ridiculous. Is there anyway to get Win7 to remember the phone tether as ONE connection only?

    Read the article

  • Some users cannot connect to Exchange Server or Outlook Web Access

    - by crn
    In our network, some users cannot connect to either Exchange Server 2007 or Outlook Web Access while others are able to connect to both. On one computer, the error occurred after the user ran the AVG anti-virus update. Some computers return this error message "Task 'Microsoft Exchange Server' reported error (0x800401 ID): The server is not available." Thanks, in advance, for your help!

    Read the article

  • Some users cannot connect to Exchange Server or Outlook Web Access

    - by crn
    0 In our network, some users cannot connect to either Exchange Server 2007 or Outlook Web Access while others are able to connect to both. On one computer, the error occurred after the user ran the AVG anti-virus update. Some computers return this error message "Task 'Microsoft Exchange Server' reported error (0x800401 ID): The server is not available." Thanks, in advance, for your help!

    Read the article

  • Right Clicking error in windows 7 windows explorer

    - by Domenik VanBuskirk
    Whenever I right-click something in windows explorer other than favorites, libraries, computer, or network (the main headings in the left pane), the drop-down menu does not appear and an error pops up "windows explorer has stopped working" - "windows explorer is restarting". Once those both close the icons on the desktop and taskbar itself blink off and back on again. Is there any way of finding out what is going on when I right click and this problem ensues?

    Read the article

  • Want to use apache, ISP blocking port 80

    - by Will
    I am attempting to set up a small web server on my home network, but my ISP is blocking incoming port 80 ( and no, i'm not paying $50/month extra for them to unblock it). I am looking for some ways around this, obviously I can change the port # but I don't find this ideal. really appreciate any ideas for this

    Read the article

  • On OS X, what is pubsubagent and why does it connect so many places?

    - by Eric
    I use Little Snitch to monitor network connections on OS X, and I frequently see attempts by something called pubsubagent to connect to many varying sites. What is this program for and why does it use so many connections? According to this article it's used by .me sync to synchronize RSS feeds and bookmarks. But I don't have any RSS feeds. And if it's synching bookmarks, then why is it going to places like 'l.google.com' (and many more random ones) instead of just to .me?

    Read the article

  • What Iptables rules need I to forward a windows remote desktop connection?

    - by avastreg
    I have this situation: network mask. 255.255.255.0 router/gateway: Ubuntu server (only command line, no gui) with internal lan ip 192.168.0.2 and a dynamic dns on the external ip Windows pc on 192.168.0.1 with RDP (remote desktop connection) enabled on 3389 I want to forward the RDP service on the external address: how can i do that? What are the iptables rules I need to connect to my Windows pc from the outside world?

    Read the article

  • Remember Snow Leopard Firewall settings

    - by revelator
    I've got the firewall enabled on my Snow Leopard installation, and it works just fine, except for with EyeTV. Every time I run this app, a popup appears asking if I want to allow it access to the network, even though I've got it added in the application list for allowed apps. Any ideas how I can stop this from asking and just let it be given access?

    Read the article

  • problem with ubuntu gnome environment

    - by Kukmedis
    Hello, after removing gnome-panel gnome doesn't start at all. I get black screen and terminal upon turning PC on. It would seem no problem but wireless network doesn't start too, so i have no internet connection to "apt-get install--reinstall". Any suggestions? Thank you

    Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >