Search Results

Search found 14377 results on 576 pages for 'video card'.

Page 433/576 | < Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >

  • radeon display driver clones monitors while using Xinerama

    - by gregmuellegger
    I'm trying to get my two Radeon HD 4770 cards working with three monitors. Xinerama works so far in the way that I have two fully working monitors were I can move windows from one to the other. My problem now is that my third monitor is a clone of my second monitor (displaying the exact same thing). These monitors are connected to the same graphic card ("Screen Middle" and "Screen Right" in the xorg.conf below). Here is my xorg.conf: Section "ServerLayout" Identifier "ThreeMonitors" Screen "Screen Left" 0 0 Screen "Screen Middle" RightOf "Screen Left" Screen "Screen Right" RightOf "Screen Middle" Option "Xinerama" EndSection Section "Monitor" Identifier "Monitor Left" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Middle" Option "DPMS" EndSection Section "Monitor" Identifier "Monitor Right" Option "DPMS" EndSection Section "Device" Identifier "Device Left" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:3:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Left" Device "Device Left" Monitor "Monitor Left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Middle" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:0" Screen 0 EndSection Section "Screen" Identifier "Screen Middle" Device "Device Middle" Monitor "Monitor Middle" SubSection "Display" Depth 24 EndSubSection EndSection Section "Device" Identifier "Device Right" Driver "radeon" VendorName "ATI Technologies Inc" BoardName "ATI Radeon HD 4770 [RV740]" BusID "PCI:2:0:1" Screen 1 EndSection Section "Screen" Identifier "Screen Right" Device "Device Right" Monitor "Monitor Right" SubSection "Display" Depth 24 EndSubSection EndSection I'm using a fresh Kubuntu 10.10 installation with propsed-updates enabled since this repo contains a xorg fix for using multiple graphic cards. I hope someone can help me out. Very many thanks!!

    Read the article

  • Wireless on ThinkPad Edge E420s

    - by user21820
    I have installed Kubuntu 11.04 (Natty) on my ThinkPad Edge E420 laptop. Unfortunately, the wireless is not working. I have got Windows 7 installed besides Kubuntu, and wireless is working with no problems there, so it has to be problem of the OS. What I tried: I installed the official driver from Realtek RLT8192CE. After reboot the wireless didn't work, but at least the system was able to detect that it is present in the system. However, after executing lscpi -v, under the card's details there was a line "Currently used driver" which said "r8169". Why is this? I did all of this according to a manual on http://www.php-architect.com/blog/2010/05/01/getting-wireless-to-work-on-lenovo-thinkpad-t400-with-ubuntu-10-4-lucid/. There a meany other similar ones, but don't work for me either. My questions are: 1) Is there any way to get this fixed? If yes, how to do so? 2) Do you think OpenSUSE (or any other distro) is better distribution concerning such hardware issues, so should I give it a try? If yes, which distro gives me the best chance?

    Read the article

  • How to connect to my own WiFi using Broadcom STA drivers?

    - by Chris
    I'm trying hard to switch to Linux from Windows because of my engineering project. Unfortunately, everything is against that change! Before I have installed Broadcom STA proprietary drivers, I was seeing on NetworkManager and nm-applet only local radio-internet-access networks. After I installed Broadcom STA, I see my neighbor's wireless network (channel 11, WEP) Neither before nor after the installation is own wireless network available. Computer: Asus Lamborghini VX6 Ubuntu: 12.04 LTS 64-bit Router: ASUS N55U (A1) with newest AsusWRT firmware Network: Channel 5 (tried also 10 and 11, both on 20 and 40MHz bands), WPA2 Personal, 2,4 + 5 GHz (what is not very important, 'cause the wlan card in VX6 is only 2,4GHz). Network works fine on Windows, also through D-Link repeater on the other floor. Unfortunately, same network is invisible to Ubuntu on same machine. I have tried some combinations with other GUIs but it did not work. Are there any better drivers for Ubuntu? I need that network badly, but I'm an Ubuntu newbie, so I don't know how to solve that problem. Please help.

    Read the article

  • How do I fix "Ubuntu is running in low-graphics mode?"

    - by Tortoise
    First off, I'm running Ubuntu 10.04 on a 30gb partition, the rest of my hdd is for a vista partition. The way I installed this was, I shrunk the vista partition and installed Ubuntu in the largest block of free space. Ubuntu has been working fine for a few weeks, and I've loved it, but today I was doing something in Vista (something simple) and I restarted to go back into ubuntu, and when it tried to boot up I got a message that said: "Ubuntu is running in low-graphics mode. Your screen, graphics card, and input devices could not be detected correctly. You will have to configure these yourself." I click OK, and it gives me a few options but all of them are dead ends. Basically, I'm stuck in CLI right now without a clue of how to fix it. I've tried doing a full update and it hasn't made a difference. I've already been asking for help in #Ubuntu and #Radeon and I was directed by some of them here, so I hope I can find some answers here. Also, I'm using an ATI Radeon X1200. Any help would be greatly appreciated. Another thing, while I was trying to get help in #radeon I was told that it could possibly be this bug.

    Read the article

  • How to write code that communicates with an accelerator in the real address space (real mode)?

    - by ysap
    This is a preliminary question for the issue, where I was asked to program a host-accelerator program on an embedded system we are building. The system is comprised of (among the standard peripherals) an ARM core and an accelerator processor. Both processors access the system bus via their bus interfaces, and share the same 32-bit global physical memory space. Both share access to the system's DRAM through the system bus. (The computer concept is similar to Beagleboard/raspberry Pie, but with a specialized accelerator added) The accelerator has its own internal memory (SRAM) which is exposed to the system and occupies a portion of the global address space (as opposed to how a graphics card would talk to teh CPU via a "small" aperture in the system memory space). On the ARM core (the host) we plan on running Ubuntu 12.04. The mode of operation of communicating between the processors should be that the host issues memory transactions on the system bus that are targeted at the accelerator internal memory. As far as my understanding goes, if I write a program for the host that simply writes to the physical address of the accelerator, most chances are that the program will crash due to a segmentation violation. So, I assume that I need some way of communicating with the device in real mode. What is the easiest way to achieve this mode of operation?

    Read the article

  • Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

    - by jindrichm
    I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

    Read the article

  • Can T520+Bumblebee run an external monitor via DisplayPort?

    - by Fen
    Using 64-bit Ubuntu 11.10 and integrated (Intel) graphics, I can run the 1600x900 laptop display plus a 1600x1200 external monitor connected to the VGA adapter. But my external monitor is 1920x1200 so I have black stripes on each side. I believe the resolution is limited like this as the maximum resolution available from the Intel GPU is 2560x1600 = 4,096,000 pixels and I'm asking for a 3520x1200 = 4,224,000 display (with 1200x300 lost above the laptop screen). At 3200x1200 = 3,840,000 pixels, the Intel GPU seems happy. Under Windows, the same limit exists when using the VGA adapter, but if I turn Optimus on then I can connect the external monitor to the DisplayPort and get its full resolution and an extended desktop. I've seen that Bumblebee can run apps on the DisplayPort using the 'optirun' command. My question is: can Bumblebee run the DisplayPort in concert with the Intel card running the laptop screen creating a large virtual desktop (as on Windows)? If so, are there any pointers to how to do this? I tried once, failed, and dropped back to Integrated Graphics (and black stripes) as I could find no reports of this configuration working.

    Read the article

  • How do I install the nvidia driver for a GeForce 9300M?

    - by Alex
    Yesterday i've installed ubuntu 11.04 (instead of 10.10). And i need to install nvidia driver which supports opengl 3.3 In 10.10 i did it in a such way: Ctrl+alt+f1 login sudo /etc/init.d/gdm stop sudo sh driver.run startx Not it doesn't work. Because ctrl+alt+f1 doesn't show login screen. Just only black screen. I've googled this problem. Some people have it but no one knows how to solve. Sometimes people say that it is connected with video card or driver. But i have GeForce 9300M G, and i've activated a standard driver. Anyway, it worked in 10.10, but doesn't work now. The main problem is that i need to kill xserver to install this driver. killing the process just only restarts xserver. Also, I've tried to /etc/init.d/gdm stop in GUI-console. It says that "Fake initctl,doing nothing". Google didn't helped in this case too. Any ideas to install that driver?

    Read the article

  • SSD on USB 3.0 doesnt always mount

    - by juergen
    I would like to ask you for some support for this issue. The SSD I use is apparently slightly damaged. Atm it shows this popular Corsair Series 3 problem. symptom: the disk is working for some minutes and then just suddenly stops. Two months ago it worked like a charm. This was my boot device in these days. So now I still need to copy some data out of the device which leads me to my question. Usually the SSD is working again for some minutes, when i unplug and replug its power. It gets detected by the system again and I can continue my backup. The problem on Ubuntu is, that it is not recognized again after two or three replugs. I have to reboot to bring it back. To specify this situation: when i unplug and replug my USB mouse before i reboot it is not recognized as well. So something seems to be wrong with the system also. my question: how do i fix this rebooting issue? I will post all the logs you need to analyse. The problem doesnt depend on the interface. I tried USB3.0, 2.0 and Sata already. Thank you! cheers my system: Ubuntu 11.10, Gigabyte G41MT-S2P, Intel E6750 Corsair Force Series 2 - F120, Digitus USB 3.0 Adapter, USB 3.0 interface card

    Read the article

  • Run a VirtualBox VM in a second X-Server with Graphic support

    - by Scindix
    I'm starting a VirtualBox VM (Windows 7) in a second X-Server (Ubuntu 14.04) and i'm using the following xinit script (/path/.vboximage): optirun VBoxManage startvm <vm name> & exec tinywm I recognized that while running Virtualbox normally under Gnome (Unity to be precise ;-) ) I get full graphics support. But when I run it on a second xserver there seem to be some problems. E.g. Windows Aero doesn't seem to work and Chrome WebGL demos are running with poorer performance. I'm not a big Windows expert, so I don't know how I could check the used Graphic card (specification). But it is very obvious that something has changed when running the vm in the extra X-Server. Also when I try to replace tinywm with compiz I get the unity frame around the VM, which also seems to have no graphics acceleration (no transparency effects) So it seems that the X-Server doesn't have Graphic acceleration at all. I have a NVidia 525m and an Intel HD3000 which are both capable of advanced graphics. I'm starting the above script with startx /path/.vboximage - :1 How could I fix that?

    Read the article

  • Bootable dvd installs ubuntu in one computer but not in other...Why? [closed]

    - by SAM
    Possible Duplicate: My computer boots to a black screen, what options do I have to fix it? I have 2 computers, Windows 7 Intel. On one computer Ubuntu boot-able DVD (AMD 64) works properly. But on other computer the same DVD boots OK but when clicked on "Install Ubuntu" a blank screen with blinking cursor(_) appears and it continues just blinking forever. What problem can be there in computer 2? Can it be DVD reader's problem? (Both computers have LG DVD RW) Can there be any problem in DVD? Computer 1 specs: Pentium D 3 GHz Windows 7 32-bit not a 64bit-capable processor still Ubuntu 64bit trial/installer runs... Computer 2 specs: Core i7 2700k Windows 7 32-bit nvidia gtx 560 graphicsCard ...BIG BOSS... still can't run the setup/trial/disk-check/memory-test ?!?!? Is it the problem of graphics card ?!? I also tried burning other dvd which has the same behavour.... AND yes the dvd name is: ubuntu-12.04.1-dvd-amd64.iso Any help is appreciated.

    Read the article

  • Computer suddenly won't boot - stops at a flashing prompt

    - by Dave M G
    I have been running Ubuntu on my computer for a long time, and I have been using 11.10 since it became available in October. Suddenly, this morning, when I rebooted, the computer would not reach the log in screen. I go through the standard POST boot sequence, and I also get a splash screen for my Nvidia graphics card, so at least most of the hardware seems to be working. After that, all I get is a flashing text prompt - one blinking white underline character on a screen that is otherwise completely blank. I don't think it is even reaching GRUB. No key input is possible. I have tried various key combinations to try and initiate some kind of interface, be it command line or anything else. The only key combination that works is [CTRL]+[ALT]+[Delete] to reboot. I realize this is likely to be a hardware problem, but it could be an Ubuntu problem(?), so I'm hoping for a specific set of troubleshooting steps so I can diagnose and repair this issue. My current suspicion is that one of the drives in my 2 disk software RAID has failed (even though they should be too new for that). However, this computer is critical to my work, so I'd like to invite advice on any possibilities so as to waste as little time as possible in fixing this machine.

    Read the article

  • ubuntu 12.10 Lenovo b570e, WiFi connected but not working

    - by koogee
    I'm running ubuntu 12.10 liveUSB on a lenovo b570e. It has an atheros wifi card that connects with my home network but I can't browse AT ALL. My network is multiple clients --> router --> isp modem --> Internet I can ping my router (192.168.0.1) but not my isp's modem(192.168.15.1). I have 3 other computers connected to the same router that are working fine (infact i'm posting from one) ping -c 3 google.com unknown host google.com ping -c 3 8.8.8.8 shows 100% packet loss I think its some networking issue. I tried directly connecting it to the router via ethernet cable but same issue. It gets an ip, shows LAN connected but can't browse. If I connect it directly to the isp modem via ethernet cable it starts working fine. Connection Information shows: Interface: 802.11 wifi (wlan0) driver: ath9k security: wpa/wpa2 speed: 150mb/s ip: 192.168.0.106 broadcast: 192.168.0.255 subnet:255.255.255.0 default route: 192.168.0.1 primary dns: 192.168.15.1 i have restarted the router and modem many times. Rebooted the LiveUSB many times.

    Read the article

  • Wireless switch on Dell XT2 - strange behaviour of rfkill

    - by DyP
    I have an Dell Latitude XT2 using an Intel WLAN card (lspci lists it as "Intel Corporation Ultimate N WiFi Link 5300") running Lubuntu 12.04 with recent updates. The laptop has a hardware WLAN switch. I have problems activating the WLAN when booting with the hardware switch set to "off". The situation is a bit confusing, unfortunately. rfkill lists two WLAN devices (though lspci only shows the Intel one). This is the situation when booting with the hardware switch set to "Off": 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes From some tests, I conclude WLAN is only activated when both, the dell-wifi and phy0, are unblocked by soft- and hardware. But I can only unblock dell-wifi after the hardware switch is set to "on". Procedure right from boot with hardware switch set to "Off": Soft-unblocking phy0 works as expected. Could be done by start-up script. sudo rfkill unblock 0: nothing happens. Soft block of dell-wifi not removed. Set the hardware switch to "on": phy0 gets its hard block removed. Still no WLAN. sudo rfkill unblock 0: both the soft and hard lock of dell-wifi are removed. WLAN is now active and works. sudo rfkill block 0: only adds the soft block as expected. WLAN goes off again. So, in order to activate WLAN, I have to use the hardware switch and afterwards (manually) run a script - that's a bit inconvenient. Does someone know a better solution? Maybe a daemon could help that listens to rfkill events to unblock dell-wifi after I have set the hardware switch to "on"? (sounds like another workaround) When booting with the hardware switch set to "On", nothing is blocked neither hard nor soft.

    Read the article

  • hd0 out of disk error results to low graphics mode

    - by msPeachy
    Yesterday, I have reinstalled Ubuntu due to a error: hd0 out of disk on boot. Everything went fine, I've installed apps, perform updates and upgraded the kernel. I've even restarted it a few times just to check if I would encounter boot issues and was glad that everything was working perfectly, then powered it down. The next morning when I boot, I got this error: hd0 out of disk error. Press any key to continue... again! After pressing a key, it took 10 minutes for the Ubuntu logo to appear with it's 5 dots. After another 5 minutes, Ubuntu started checking the disk and displayed a message that / has errors, I pressed F to fix the errors. After which Ubuntu tells me that /tmp is not yet ready for mounting so I pressed S to skip mounting it, then Ubuntu restarted. On boot I saw the error: hd0 out of disk error. Press any key to continue... again. This time it took only a minute for the Ubuntu logo to appear and after another minute a dialog box appeared with the following message: The system is running in low-graphics mode. Your screen, graphics card, and input settings could not be detected correctly. You will have to configure these yourself. What would you like to do? Run in low-graphics mode for just one session Reconfigure graphics Troubleshoot the error Exit to console login Whichever option I choose I ended up with a console prompt: grub-editenv: error: cannot read the file /boot/grub/grubenv. _ I can't do anything on this console, whatever I type nothing happens. I've rebooted several times and I get same error every time. I don't quite understand what is wrong with Ubuntu or with my installation. I've encountered this hd0 out of disk error several times already and always ended up reinstalling. I'd really really appreciate it if you guys can help me fix this. Thank you and good day.

    Read the article

  • I can't get grub menu to show up during boot

    - by wim
    After trying (and failing) to install better ATI drivers in 11.10, I've somehow lost my grub menu at boot time. The screen does change to the familiar purple colour, but instead of a list of boot options it's just blank solid colour, and then disappears quickly and boots into the default entry normally. How can I get the bootloader back? I've tried sudo update-grub and also various different combinations of resolutions and colour depths in startupmanager application with no success (640x480, 1024x768, 1600x1200, 16 bits, 8 bits, 10 second delay, 7 second delay, 2 second delay...) edit: I have already tried holding down Shift during bootup and it does not seem to change the behaviour. I get the message "GRUB Loading" in the terminal, but then the place where the grub menu normally appears I get a solid blank magenta screen for a while. Here are the contents of /etc/default/grub # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX=" vga=798 splash" # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux #GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

    Read the article

  • HP DV6 connects but no internet

    - by Frank Barcenas
    I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

    Read the article

  • Asus A8V overcurrent

    - by user139710
    This is not as much as a question as it is a note to those out there that upgrade their motherboards with better processors and the like. Here's my story. Recently I upgraded my processor. System specifications: • Asus A8V Deluxe • 4GB RAM • ATI Radeon 3870 AGP graphics card (I believe that's it) Anyway, I decided to put a dual core Opteron 180 in this rig, but the problem was that I needed to update the BIOS to V-1017, and not knowing the consequences, I went up to the Asus site and got the newest, the latest and the greatest, 1018.002 thinking that it was the best for this board, however it wasn't. I used the Asus EXFlash, which makes life a lot easier, flashed the BIOS and all of a sudden I start getting this message: USB overcurrent protection, system shutting down in 15 seconds to protect your system. WELL SHIT... This is a new one on me... I read the blogs, all the posts on this thing, and did all that everyone else did to correct the problem, but nothing helped. So i decided to start from square one, went back to Asus and looked at the BIOS download... OMG... IT WAS A BETA. So, I downloaded the update that was suggested 1017< and installed it and wouldn't you know, it took care of the problem, no more USB overcurrent protection, no more crashing. I write this today to let you all know about this, just in case you have an issue such as this. Well there you all go. Fly safe and eat your vegetables.

    Read the article

  • I still can't figure out how to program!

    - by Mark K.
    Please help! I've read lots of programming books for various languages, Java, Python, C, etc. I understand and know all of the basics of the languages and I understand algorithms and data structures. (Equivilant of say 2 years of CompSci classes) BUT, I still can't figure how to write a program that does anything useful. All of the programming books show you how to write the language, but NOT how to use it! The programming examples are all very basic like build a card catalog for a library or a simple game or use algorithms etc... They dont't show you how to develop complex programs that actually do anything useful! I've looked a open-source programs on sourceforge, but they don't make much sense to me. There are hundreds of files in each program & thousands of lines of code. But how do I learn how to do this? There's nothing in any book I can buy on Amazon that will give me the tools to write any of these programs. How do you go from reading Intro to Java or Programming Python, or C Programming Language, etc.. to actually being able to say, I have an idea for X Program.. this is how I go about developing it? It seems like there is so much more involved in writing a program than you can learn in a book or from a class. I feel like there is someth Can anyone put me on the right track?

    Read the article

  • Ubuntu 12.04 still slow at mounting internal filesystem

    - by Matthew Goson
    I'm using Toshiba laptop with this configuration: - CPU: Core i5, 2.4GHz - RAM: 4GB - Graphics card: Intel - Hard disk: 500GB SATA I installed Ubuntu 12.04 64bit and got the same issue with this guy Very slow boot due to mounting filesytem, I tried all suggestions there but the slow boot issue still here. Here's a part of my dmesg: [ 2.041015] usbhid: USB HID core driver [ 2.101378] usb 1-1.6: new full-speed USB device number 5 using ehci_hcd [ 2.137980] atl1c 0000:04:00.0: version 1.0.1.0-NAPI [ 2.779080] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 22.822597] udevd[381]: starting version 175 [ 22.837954] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.850837] lp: driver loaded but no devices found [ 23.003822] Adding 7079096k swap on /dev/sda7. Priority:-1 extents:1 across:7079096k [ 23.407915] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 23.408153] mei 0000:00:16.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 23.408160] mei 0000:00:16.0: setting latency timer to 64 [ 23.408211] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 23.433196] [drm] Initialized drm 1.1.0 20060810 Additional information: my sda1 is a primary NTFS partition, sda2 is a primary ext4 partition which I installed Ubuntu onto. Other partitions are inside an extended partition.

    Read the article

  • Update Manager got stuck (but not frozen) while installing downloaded updates. What should I do?

    - by WarriorIng64
    I have just gotten my Ubuntu 12.04 LTS desktop computer reassembled after a trip back home and connected it to my parent's wireless Internet connection. The connection seems quite shaky (disconnects half the time, likely an ongoing issue with the wireless card I have installed), and it struggled to download updates because of the constant interruptions. Eventually, it managed to download the updated packages and started installing them. I got up and left it to do its work. When I came back, I saw it was still having trouble staying connected to the wireless (no surprise there), but then I noticed that it seemed like Update Manager had stopped making progress on the installation. I opened the Details pane to see what it was last doing: My guess was that the installation script for flashplugin-installer couldn't complete the download until I stabilized the Internet connection. I hooked my Ubuntu laptop up to my desktop via Ethernet and shared its wireless connection using this guide, and as I am typing this now from my desktop you can see that the connection issue was successfully worked around. However, even with a stable connection established, Update Manager seems "stuck" at its current position and won't go any further. It's not totally frozen, but I can't do anything beyond open/close the Details pane as the Cancel button is grayed out. I know it can cause big problems if updates are stopped during installation, but I'm at a loss as to how this situation should be handled. I'm sure it should finish normally if I can just find a way to restart Update Manager, but the question is how this should be approached. How can I safely get my updates to finish installing?

    Read the article

  • Nvidia driver installation results in resolution change to 800x600 with Xubuntu 10.04 (can't change)

    - by Jim Michael
    I have a 2.8 P4 and a Nvidia FX 5500 AGP graphics card. I've installed Xubuntu 10.04. It is WAY too laggy with the default o/s driver. Installing the Nvidia 173 driver, modaliases and nvidia-settings packages via synaptic package manager results in the following error message: An error occurred, please run Package Manager from the right click menu or apt-get in a terminal to see what is wrong. Error: Opening the cache (E::read, still have 11898251 to read but none left, E: The package lists or status file could not be parsed or opened.) This usually means that your installed packages have unmet dependencies. When restarting the PC the resolution drops to 800x600 (from the monitors native 1440x900). Nvidia settings cannot be changed either from the Xfce menu or Nvidia Xserver. Nvidia Xsever gives the following error message: You do not appear to be using the Nvidia X driver. Please edit your x configuration file (just run 'nvidiaxconfig' as root ) and restart X server. Also, I can't find anything in any directory called xorg.

    Read the article

  • Graphics hardware warning when updating to 14.04

    - by pacomet
    As I use Ubuntu at work I just update only LTS versions but now I'm not sure if I can/should. As my computer is now ten years old I would change if was mine but as it is owned by my employer I have to work with it. It's not a bad one, it runs fine (this was not true when still had Windows on it ;-). When updating to 14.04, it warns about possible bad/slow performance with Unity 3D so I stop updating as I am at work, not my own computer. As I understand from http://askubuntu.com/a/438958/25305 Nvidia Geforce FX 5500 graphics card is still supported in 14.04. Now, in 12.04, I have driver version 173 and unity 2d runs fine for me. output of /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce FX 5500/AGP/SSE2 OpenGL version string: 2.1.2 NVIDIA 173.14.39 Not software rendered: yes Not blacklisted: no GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Should I update? Is it better to stay with 12.04? Thanks

    Read the article

  • Can't get Unity 3D to work in 11.10

    - by pmoseph
    I recently upgraded to 11.10 on my Lenovo ThinkPad T520, and I'm not able to load Unity 3D (I'm not selecting 2D at login menu either). me@mycomp:~$ echo $DESKTOP_SESSION ubuntu-2d I ran the unity support test below as well. me@mycomp:~$ /usr/lib/nux/unity_support_test -p Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Error: unable to create the OpenGL context And it looks like I only have one graphics card: me@mycomp:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Also, Ubuntu lists nothing under the "Additional Drivers" window. Any help would be extremely appreciated as I'm somewhat of a noob. Thanks! Edit 1: Here is the output of lshw -C display me@mycomp:~$ sudo lshw -C display *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:43 memory:f0000000-f03fffff memory:e0000000-efffffff ioport:5000(size=64)

    Read the article

  • Installing ubuntu 12.04 on macbook pro9,2

    - by stariz77
    I seem to have tried all the various suggested methods for installing ubuntu on a mbp, but can't seem to get anything that works and was wondering if anyone has run into any new problems with the latest non-retina models? I have a core i7 in my macbook, and model identifier is MacBookPro9,2. I have partitioned my HD using disk utility and have 700gig free space ready for the install (I haven't removed OSX Lion, it is still there in a 50gig partition). Problem: I am just getting a blank screen with a blinking cursor (unresponsive) in the top left whenever I boot from the disk. I left it for 20 minutes and nothing ever happened. This was without any boot manager, just holding "c" on startup. Attempted remedies: I have downloaded the 64 ubuntu iso from their site 3 times now and burned 4 separate discs to rule out some kind of corruption or burn error. I burned one in OSX Lion 10.7.4 and 3 on my windows 7 pc. I tried holding "alt" instead and then navigating to the windows disc to boot. Same thing happens, blank blinking unresponsive cursor. I also tried going to the EFI disc which actually brings up a menu (after saying "error prefix is not set") asking if I want to install ubuntu, test for errors or partition. All three options lead me to an unresponsive blank screen (some without cursors). I downloaded and installed rEFIt and if I hold "alt" on startup a linux penguin (Boot Linux from CD) appears in my boot options, along with the apple boot, and two others that I'm not sure of: "Boot EFI\boto\bootx64.efi from" and "Boot Legacy OS from". The "Boot Linux from CD" just takes me to the blank blinking cursor screen; again, I left if for 10+ minutes and nothing. I heard that the detection of the graphics card might be a problem and that I need change to nomodeset, but I have tried pressing F6 in all of the boot menus listed above and no options appear. Does anyone have any other suggested routes or can you see what I might have done wrong?

    Read the article

< Previous Page | 429 430 431 432 433 434 435 436 437 438 439 440  | Next Page >