Search Results

Search found 45505 results on 1821 pages for 'change directory'.

Page 436/1821 | < Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >

• Bridged virtual interface is not available or visible to ifconfig.

  - by Omniwombat

  Hello all. I'm running Ubuntu 9.04, kernel 2.6.28-18, and vmware-server 2.0.1. I'm attempting to setup a virtual linux machine to use a bridged interface rather than NAT or host-only. Both NAT and host-only work just fine. When running vmware-config.pl, I set /dev/vmnet0 to bridge eth0, /dev/vmnet1 to host-only, and /dev/vmnet8 to NAT. When I run ifconfig -a I see the physical interface (eth0), vmnet1 and vmnet8 both of which are up and have IP addresses assigned to them. I also see other various interfaces that are not relevant here. In the web console, when I ask that the guest machine's network card be bridged, it states that a bridged setup is "Not available" and shows the disabled device icon. Inside the guest machine, I do have an eth0 interface which I can set to anything I like, however it can't see my external network, or the host. I do see errors in my vmware/hostd.log which state: "The network bridge on device vmnet0 is not running. The virtual machine will not be able to communicate with the host or with other machines on your network" which confirms the problem. vmnet-bridge is running, and I see the following in my process table: /usr/bin/vmnet-bridge -d /var/run/vmnet-bridge-0.pid -n 0 -i eth0 I confirm that the /var/run/vmnet-bridge-0.pid file is there and that it points to the correct process. I saw this question relating to Ubuntu 9.04 and bridged interfaces, in which the poster determined that the vsock library was not getting built due to a flaw in the vmware-config.pl script. I applied the patch, reran the script, and confirm that vsock.ko and vsock.o are in my /lib directory structure. vsock does show up in an lsmod. My /etc/vmware directory has /vmnet1 and /vmnet8 subdirectories. They contain configuration utilities for running DHCP and nat type services as expected. There is no vmnet0 subdirectory. My /etc/vmware/netmap.conf file DOES show entries for vmnet0; both the name and the device as I configured it from the script. My /dev directory contains devices vmnet0 through vmnet9. They have major device number 119, and minor device numbers 0 through 9. /proc/net/dev shows statistics for vmnet1 and vmnet8, but not vmnet0. I have a /proc/vmnet directory, but it's empty. When I start or stop the vmware service with /etc/init.d/vmware start, I see the following: Starting VMware services: Virtual machine monitor done Virtual machine communication interface done VM communication interface socket family: done Virtual ethernet done Bridged networking on /dev/vmnet0 done Host-only networking on /dev/vmnet1 (background) done DHCP server on /dev/vmnet1 done Host-only networking on /dev/vmnet8 (background) done DHCP server on /dev/vmnet8 done NAT service on /dev/vmnet8 done VMware Server Authentication Daemon (background) done Shared Memory Available done Starting VMware management services: VMware Server Host Agent (background) done VMware Virtual Infrastructure Web Access Starting VMware autostart virtual machines: Virtual machines done Nothing appears to be wrong there. What n00b thing am I doing such that vmnet0 and only vmnet0 does not show up in the interface list?

  Read the article

• Custom Templates: Using user exits

  - by Anthony Shorten

  One of the features of Oracle Utilities Application Framework V4.1 is the ability to use templates and user exits to extend the base configuration files. The configuration files used by the product are based upon a set of templates shipped with the product. When the configureEnv utility asks for configuration settings they are stored in a configuration file ENVIRON.INI which outlines the environment settings. These settings are then used by the initialSetup utility to populate the various configuration files used by the product using templates located in the templates directory of the installation. Now, whilst the majority of the installations at any site are non-production and the templates provided are generally adequate for that need, there are circumstances where extension of templates are needed to take advantage of more advanced facilities (such as advanced security and environment settings). The issue then becomes that if you alter the configuration files manually (directly or indirectly) then you may lose all your custom settings the next time you run initialSetup. To counter this we allow customers to either override templates with their own template or we now provide user exits in the templates to add fragments of configuration unique to that part of the configuration file. The latter means that the base template is still used but additions are included to provide the extensions. The provision of custom templates is supported but as soon as you use a custom template you are then responsible for reflecting any changes we put in the base template over time. Not a big task but annoying if you have to do it for multiple copies of the product. I prefer to use user exits as they seem to represent the least effort solution. The way to find the user exits available is to either read the Server Administration Guide that comes with your product or look at individual templates and look for the lines: #ouaf_user_exit <user exit name> Where <user exit name> is the name of the user exit. User exits are not always present but are in places that we feel are the most likely to be changed. If a user exit does not exist the you can always use a custom template instead. Now lets show an example. By default, the product generates a config.xml file to be used with Oracle WebLogic. This configuration file has the basic setting contained in it to manage the product. If you want to take advantage of the Oracle WebLogic advanced settings, you can use the console to make those changes and it will be reflected in the config.xml automatically. To retain those changes across invocations of initialSetup, you need to alter the template that generates the config.xml or use user exits. The technique is this. Make the change in the console and when you save the change, WebLogic will reflect it in the config.xml for you. Compare the old version and new version of the config.xml and determine what to add and then find the user exit to put it in by examining the base template. For example, by default, the console is not automatically deployed (it is deployed on demand) in the base config.xml. To make the console deploy, you can add the following line to the templates/CM_config.xml.win.exit_3.include file (for windows) or templates/CM_config.xml.exit_3.include file (for linux/unix): <internal-apps-deploy-on-demand-enabled>false</internal-apps-deploy-on-demand-enabled> Now run initialSetup to reflect the change and if you check the splapp/config/config.xml file you will see the change applied for you. Now how did I know which include file? I check the template for config.xml and found there was an user exit at the right place. I prefixed my include filename with "CM_" to denote it as a custom user exit. This will tell the upgrade tools to leave that file alone whenever you decide to upgrade (or even apply fixes). User exits can be powerful and allow customizations to be added for advanced configuration. You will see products using Oracle Utilities Application Framework use this exits themselves (usually prefixed with the product code). You are also taking advantage of them.

  Read the article

• Wordpress Permissions OS X & MAMP

  - by Matt2020

  I have installed several local versions of Wordpress for development purposes. After the install I can create posts, pages and edit admin options. However as soon as try to upload images which would be saved in wp_content/uploads I get an error: Upload Error: Unable to create directory ...../blog/wp-content/uploads/2011/05. Is its parent directory writable by the server? Looks like MAMP server runs as user _www The blog directory is owned by User1 and the group User1 _www is not in the User1 group, should it be? I do not want to chmod 777 or 765 on the directories just to get it going. Googled up a couple of references: http://codex.wordpress.org/Changing_File_Permissions in "Permission Scheme for WordPress" All files should be owned by your user (ftp) account on your web server, and should be writable by that account. On shared hosts, files should never be owned by the webserver process itself (sometimes this is www, or apache, or nobody user). Any file that needs write access from WordPress should be owned or group-owned by the user account used by the WordPress (which may be different than the server account). For example, you may have a user account that lets you FTP files back and forth to your server, but your server itself may run using a separate user, in a separate usergroup, such as dhapache or nobody. If WordPress is running as the FTP account, that account needs to have write access, i.e., be the owner of the files, or belong to a group that has write access. In the latter case, that would mean permissions are set more permissively than default (for example, 775 rather than 755 for folders, and 664 instead of 644). User and group are User1 (which is admin). Running "ps aux | grep httpd" is running as _www So I think this means Wordpress is running as user _www. So the advice seems contradictory: "files should never be owned by the webserver process" i.e. _www but then later it says "Any file that needs write access from WordPress should be owned or group-owned by the user account used by the WordPress" So isn't this _www again? Another search found this url http://dancingengineer.com/computing/2009/07/how-to-install-wordpress-on-mac-os-x-leopard States Which says: My preferred way to do this is to change the group of the wordpress directory and its contents to _www and give write permissions to the group. Keep the owner as your "username". $ cd /Users/"username"/Sites $ sudo chown -R username:_www wordpress_directory $ sudo chmod -R g+w wordpress_directory However, when I tried this, it did not work for automatic upgrades to newer versions of WordPress although it worked for automatically updating the .htaccess file for pretty permalinks. It is not entirely clear to me what should be done. This last suggestion seems to be saying change the group from User1 to _www and give the group write access, but Wordpress upgrades won't work. Is this the right solution? I would have thought there would be a clear way to set this up on OS X 10.6? Be great if there was a plugin that could run a script for each of the main OS's that Wordpress runs on.

  Read the article

• Handling Configuration Changes in Windows Azure Applications

  - by Your DisplayName here!

  While finalizing StarterSTS 1.5, I had a closer look at lifetime and configuration management in Windows Azure. (this is no new information – just some bits and pieces compiled at one single place – plus a bit of reality check) When dealing with lifetime management (and especially configuration changes), there are two mechanisms in Windows Azure – a RoleEntryPoint derived class and a couple of events on the RoleEnvironment class. You can find good documentation about RoleEntryPoint here. The RoleEnvironment class features two events that deal with configuration changes – Changing and Changed. Whenever a configuration change gets pushed out by the fabric controller (either changes in the settings section or the instance count of a role) the Changing event gets fired. The event handler receives an instance of the RoleEnvironmentChangingEventArgs type. This contains a collection of type RoleEnvironmentChange. This in turn is a base class for two other classes that detail the two types of possible configuration changes I mentioned above: RoleEnvironmentConfigurationSettingsChange (configuration settings) and RoleEnvironmentTopologyChange (instance count). The two respective classes contain information about which configuration setting and which role has been changed. Furthermore the Changing event can trigger a role recycle (aka reboot) by setting EventArgs.Cancel to true. So your typical job in the Changing event handler is to figure if your application can handle these configuration changes at runtime, or if you rather want a clean restart. Prior to the SDK 1.3 VS Templates – the following code was generated to reboot if any configuration settings have changed: private void RoleEnvironmentChanging(object sender, RoleEnvironmentChangingEventArgs e) {     // If a configuration setting is changing     if (e.Changes.Any(change => change is RoleEnvironmentConfigurationSettingChange))     {         // Set e.Cancel to true to restart this role instance         e.Cancel = true;     } } This is a little drastic as a default since most applications will work just fine with changed configuration – maybe that’s the reason this code has gone away in the 1.3 SDK templates (more). The Changed event gets fired after the configuration changes have been applied. Again the changes will get passed in just like in the Changing event. But from this point on RoleEnvironment.GetConfigurationSettingValue() will return the new values. You can still decide to recycle if some change was so drastic that you need a restart. You can use RoleEnvironment.RequestRecycle() for that (more). As a rule of thumb: When you always use GetConfigurationSettingValue to read from configuration (and there is no bigger state involved) – you typically don’t need to recycle. In the case of StarterSTS, I had to abstract away the physical configuration system and read the actual configuration (either from web.config or the Azure service configuration) at startup. I then cache the configuration settings in memory. This means I indeed need to take action when configuration changes – so in my case I simply clear the cache, and the new config values get read on the next access to my internal configuration object. No downtime – nice! Gotcha A very natural place to hook up the RoleEnvironment lifetime events is the RoleEntryPoint derived class. But with the move to the full IIS model in 1.3 – the RoleEntryPoint methods get executed in a different AppDomain (even in a different process) – see here.. You might no be able to call into your application code to e.g. clear a cache. Keep that in mind! In this case you need to handle these events from e.g. global.asax.

  Read the article

• Take Snapshots of Your Favorite Movie Scenes in VLC

  - by DigitalGeekery

  Have you ever wanted to grab a screenshot of your favorite TV or movie scene? Today we’ll show you how to do so with VLC Media Player. If you don’t have it already, download and install the latest version of VLC (link below). Start playing your movie, and to grab a snapshot, select Video from the menu and click Snapshot.   When you take a snapshot, by default a preview is displayed at the top left and the folder where the file is saved is briefly displayed on the screen. If you enable the Advanced Controls, you can take a snapshot with a click of a button, and advance the video frame by frame to get a more accurate shot. To enable the Advanced Controls, select View and Advanced Controls.   You’ll see the Advanced Controls buttons appear below the slider. Now just click on the Snapshot button to grab an image.   You can more easily control the frame you wish to grab by pressing the Frame by Frame button. You can pause the movie when it is near the perfect spot for your snapshot, and then press the Frame by Frame button to advance a single frame at a time. By default, the snapshots are saved as PNG files in your My Pictures folder in Windows. You can change those setting in the Preferences. First, you’ll need to select All under Show settings at the bottom. Then click on Video on the left. Scroll down a bit and you’ll see the Snapshot section. Here you can change the format from PNG to JPG, change the directory to which the snapshots are stored, turn on and off the preview, and change the filename prefix. Click Save when finished.   Now you have nice screenshots of your favorite movie to display as you wish…such as a Desktop Background!   VLC is an excellent media player that runs on Windows, Mac, and Linux. In addition to playing almost any media file, it also makes grabbing screenshots of your videos a breeze. Want to know more about VLC? Check out some of our previous articles like how to rip DVDs and how to set a video as your desktop wallpaper. Download the Latest version of VLC Similar Articles Productive Geek Tips Desktop Fun: Rural Scenes WallpapersAutomatically Mount and View ISO files in Windows 7 Media CenterHow to Make/Edit a movie with Windows Movie Maker in Windows VistaAdd Images and Metadata to Windows 7 Media Center Movie LibraryQuickly Find Movies to Watch at Hello Movies TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 tinysong gives a shortened URL for you to post on Twitter (or anywhere) 10 Superb Firefox Wallpapers OpenDNS Guide Google TV The iPod Revolution Ultimate Boot CD can help when disaster strikes

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• Universities 2030: Learning from the Past to Anticipate the Future

  - by Mohit Phogat

  What will the landscape of international higher education look like a generation from now? What challenges and opportunities lie ahead for universities, especially “global” research universities? And what can university leaders do to prepare for the major social, economic, and political changes—both foreseen and unforeseen—that may be on the horizon? The nine essays in this collection proceed on the premise that one way to envision “the global university” of the future is to explore how earlier generations of university leaders prepared for “global” change—or at least responded to change—in the past. As the essays in this collection attest, many of the patterns associated with contemporary “globalization” or “internationalization” are not new; similar processes have been underway for a long time (some would say for centuries).[1] A comparative-historical look at universities’ responses to global change can help today’s higher-education leaders prepare for the future. Written by leading historians of higher education from around the world, these nine essays identify “key moments” in the internationalization of higher education: moments when universities and university leaders responded to new historical circumstances by reorienting their relationship with the broader world. Covering more than a century of change—from the late nineteenth century to the early twenty-first—they explore different approaches to internationalization across Europe, Asia, Australia, North America, and South America. Notably, while the choice of historical eras was left entirely open, the essays converged around four periods: the 1880s and the international extension of the “modern research university” model; the 1930s and universities’ attempts to cope with international financial and political crises; the 1960s and universities’ role in an emerging postcolonial international development apparatus; and the 2000s and the rise of neoliberal efforts to reform universities in the name of international economic “competitiveness.” Each of these four periods saw universities adopt new approaches to internationalization in response to major historical-structural changes, and each has clear parallels to today. Among the most important historical-structural challenges that universities confronted were: (1) fluctuating enrollments and funding resources associated with global economic booms and busts; (2) new modes of transportation and communication that facilitated mobility (among students, scholars, and knowledge itself); (3) increasing demands for applied science, technical expertise, and commercial innovation; and (4) ideological reconfigurations accompanying regime changes (e.g., from one internal regime to another, from colonialism to postcolonialism, from the cold war to globalized capitalism, etc.). Like universities today, universities in the past responded to major historical-structural changes by internationalizing: by joining forces across space to meet new expectations and solve problems on an ever-widening scale. Approaches to internationalization have typically built on prior cultural or institutional ties. In general, only when the benefits of existing ties had been exhausted did universities reach out to foreign (or less familiar) partners. As one might expect, this process of “reaching out” has stretched universities’ traditional cultural, political, and/or intellectual bonds and has invariably presented challenges, particularly when national priorities have differed—for example, with respect to curricular programs, governance structures, norms of academic freedom, etc. Strategies of university internationalization that either ignore or downplay cultural, political, or intellectual differences often fail, especially when the pursuit of new international connections is perceived to weaken national ties. If the essays in this collection agree on anything, they agree that approaches to internationalization that seem to “de-nationalize” the university usually do not succeed (at least not for long). Please continue reading the other essays at http://globalhighered.wordpress.com/

  Read the article

• Windows 7, HTTPS WebDav: Asks for password twice and fails. Any workarounds?

  - by AutoDMC

  Howdy. I have a Dav server running with PHP SabreDav (code.google.com/p/sabredav/wiki/Windows) on Cherokee at an HTTPS secured URL. It's set to use https, and uses Digest Authentication. I can log in with multiple browsers and a few third party clients (BitKinex and Java AnyClient can connect and browse as well, caveats below). However, when attempting to log in with Windows 7 (surprise, surprise), it asks for my password twice, then tells me that my folder is invalid. I have verified that the server is using Digest authentication. I've verified multiple times that third party software can connect. I even went out and bought a GoDaddy SSL certificate so my SSL wouldn't be self signed anymore. I've applied the registry hacks here: support.microsoft.com/kb/943280 (Note that the article says the "fix" already exists for Windows 7, I just need magical registry hax to get it to work) I've applied the registry hacks here: support.microsoft.com/kb/941050 I've applied the registry hacks here: support.microsoft.com/kb/841215 (Supposedly allows Basic Auth, which shouldn't apply, but why not?) All to no avail; Windows continues to ask for my password twice, then state that "The folder you entered does not appear to be valid. Please choose another." Try the command line? Sure: I've attempted to access with NET USE "https://dav.example.com/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/" (System error 1790) I've attempted to access with NET USE "https://dav.example.com/subdir/" password /USER:me (System error 59) I've attempted to access with NET USE "https://dav.example.com/subdir/" (System error 1790) For good luck: ping dav.example.com ... works. And again, web browsers can access the share just fine, so can third party tools. Best I can tell at this point is "HAHA, NO WEBDAV FOR YOU ON WINDOWS 7" which would be fine except everyone who will be using this application... uses Windows 7. And most are not as persistent or pugnacious as I am. I feel like I've burned through every random suggestion I've found anywhere in the first 10 pages of Google on every search term I can think of. Any ideas? I need it to be Webdav, I need it to be over HTTPS, and I really do need a method to access it from Windows 7. EXTRA DETAIL: However, the "third party" programs I've tried have either been buggy, incomplete, or have silly ... "glitches." For example, BitKinex seems to fixate on any http error codes sent, so if there's a glitch reading a directory, BAM, that directory is always listed empty. Long directory listings also show up as blank, even though the transfer panel shows that directory listing is still taking place. In any case, BitKinex is useless for development purposes for the reasons above. And besides, I'm building this for people other than myself, people who will want to get this dav share working "the regular way."

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• amplified reflected attack on dns

  - by Mike Janson

  The term is new to me. So I have a few questions about it. I've heard it mostly happens with DNS servers? How do you protect against it? How do you know if your servers can be used as a victim? This is a configuration issue right? my named conf file include "/etc/rndc.key"; controls { inet 127.0.0.1 allow { localhost; } keys { "rndc-key"; }; }; options { /* make named use port 53 for the source of all queries, to allow * firewalls to block all ports except 53: */ // query-source port 53; /* We no longer enable this by default as the dns posion exploit has forced many providers to open up their firewalls a bit */ // Put files that named is allowed to write in the data/ directory: directory "/var/named"; // the default pid-file "/var/run/named/named.pid"; dump-file "data/cache_dump.db"; statistics-file "data/named_stats.txt"; /* memstatistics-file "data/named_mem_stats.txt"; */ allow-transfer {"none";}; }; logging { /* If you want to enable debugging, eg. using the 'rndc trace' command, * named will try to write the 'named.run' file in the $directory (/var/named"). * By default, SELinux policy does not allow named to modify the /var/named" directory, * so put the default debug log file in data/ : */ channel default_debug { file "data/named.run"; severity dynamic; }; }; view "localhost_resolver" { /* This view sets up named to be a localhost resolver ( caching only nameserver ). * If all you want is a caching-only nameserver, then you need only define this view: */ match-clients { 127.0.0.0/24; }; match-destinations { localhost; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; /* these are zones that contain definitions for all the localhost * names and addresses, as recommended in RFC1912 - these names should * ONLY be served to localhost clients: */ include "/var/named/named.rfc1912.zones"; }; view "internal" { /* This view will contain zones you want to serve only to "internal" clients that connect via your directly attached LAN interfaces - "localnets" . */ match-clients { localnets; }; match-destinations { localnets; }; recursion yes; zone "." IN { type hint; file "/var/named/named.ca"; }; // include "/var/named/named.rfc1912.zones"; // you should not serve your rfc1912 names to non-localhost clients. // These are your "authoritative" internal zones, and would probably // also be included in the "localhost_resolver" view above :

  Read the article

• Issue in nginx proxying to apache

  - by Luis Masuelli

  My current nginx configuration is as follows: specific configuration for (currently two) domains: server { listen 443 ssl; server_name studiotv.service.tebusco.lan phpmyadmin.service.tebusco.lan; ssl_certificate /home/administrador/nginx-confs/ssl/service.tebusco.lan.crt; ssl_certificate_key /home/administrador/nginx-confs/ssl/service.tebusco.lan.key; location / { proxy_pass http://127.0.0.1:8180; proxy_set_header Host $http_host:8180; } } default configuration for unmatched ssl connections: server { listen 443 default ssl; ssl_certificate /home/administrador/nginx-confs/ssl/service.tebusco.lan.crt; ssl_certificate_key /home/administrador/nginx-confs/ssl/service.tebusco.lan.key; location / { return 403; } } http configuration: server { listen 80; rewrite ^ https://$host$request_uri? permanent; } The intention is clear: Redirect http traffic to https. Proxy each https:// call from phpmyadmin.service.tebusco.lan and studiotv.service.tebusco.lan to apache2. This includes passing a host header, which is detected. Each unmatched ssl connection must return a 403 in nginx. Does not even reach apache2. In the apache2 side of the life, I have a default site, and a non-default site which will match studiotv.service.tebusco.lan: 000-default.conf file (available and enabled): <VirtualHost 127.0.0.1:8180> # The ServerName directive sets the request scheme, hostname and port that # the server uses to identify itself. This is used when creating # redirection URLs. In the context of virtual hosts, the ServerName # specifies what hostname must appear in the request's Host: header to # match this virtual host. For the default virtual host (this file) this # value is not decisive as it is used as a last resort host regardless. # However, you must set it for any further virtual host explicitly. ServerName localhost ServerAdmin webmaster@localhost DocumentRoot /var/www/html <Directory /var/www/html> Order deny,allow Require all granted </Directory> </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet studiotv.conf file (available and enabled): <VirtualHost *:8180> ServerName studiotv.service.tebusco.lan ServerAdmin [email protected] DocumentRoot /var/www/studiotv <Directory /var/www/studiotv/> Options -Indexes +FollowSymLinks AllowOverride None Order deny,allow Allow from all Require all granted </Directory> # Available loglevels: trace8, ..., trace1, debug, info, notice, warn, # error, crit, alert, emerg. # It is also possible to configure the loglevel for particular # modules, e.g. #LogLevel info ssl:warn # No usamos ${APACHE_LOG_DIR} sino en su lugar /var/log/<host> ErrorLog /var/log/apache2/studiotv/error.log CustomLog /var/log/apache2/studiotv/access.log combined </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet However, when I hit the browser with http://studiotv.service.tebusco.lan, the default php page is shown instead. Question: What am I missing? (apache 2.4.7, nginx 1.6.0, ubuntu server 14.04).

  Read the article

• Optimise Apache for EC2 micro instance

  - by Shiyu Sekam

  I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

  Read the article

• ASPNET MVC - Override Html.TextBoxFor(model.property) with a new helper with same signature?

  - by JK

  I want to override Html.TextBoxFor() with my own helper that has the exact same signature (but a different namespace of course) - is this possible, and if so, how? The reason for this is that I have 100+ views in an already existing app, and I want to change the behaviour of TextBoxFor so that it outputs a maxLength=n attribute if the property has a [StringLength(n)] annotation. The code for automatically outputting maxlength=n is in this question: http://stackoverflow.com/questions/2386365/maxlength-attribute-of-a-text-box-from-the-dataannotations-stringlength-in-mvc2. But my question is not a duplicate - I am trying creating a more generic solution: where the DataAnnotaion flows into the html automatically without any need for additional code by the person writing the view. In the referenced question, you have to change every single Html.TexBoxFor to a Html.CustomTextBoxFor. I need to do it so that the existing TextBoxFor()'s do not need to be changed - hence creating a helper with the same signature: change the behaviour of the helper method, and all existing instances will just work without any changes (100+ views, at least 500 TextBoxFor()s - don't want to manually edit that). I tried this code: (And I need to repeat it for each overload of TextBoxFor, but once the root problem is solved, that will be trivial) namespace My.Helpers { public static class CustomTextBoxHelper { public static MvcHtmlString TextBoxFor<TModel, TProperty>(this HtmlHelper<TModel> htmlHelper, Expression<Func<TModel, TProperty>> expression, object htmlAttributes, bool includeLengthIfAnnotated) { // implementation here } } } But I am getting a compiler error in the view on Html.TextBoxFor(): "The call is ambiguous between the following methods or properties" (of course). Is there any way to do this? Is there an alternative approach that would allow me to change the behaviour of Html.TextBoxFor, so that the views that already use it do not need to be changed?

  Read the article

• Combobox with collection view itemssource does not update selection box item on changes to the Model

  - by Vinit Sankhe

  Hello, Sorry for the earlier lengthy post. Here is my concise (!) description. I bind a collection view to a combobox as a itemsSource and also bind its selectedvalue with a property from my view model. I must keep IsSynchronizedWithCurrentItem="False". I change the source list ofr the view and then refresh the view. The changed (added, removed, edited) items appear correctly in the item list of the combo. But problem is with the selected item. When I change its property which is also the displaymember path of the combo, the changed property value does not reflect back on the selecton box of the combo. If you open the combo dropdown it appears correctly on the item list but not on the selection box. Now if I change the combobox tag to Listbox in my XAML (keeping all attributes as it is) then when selected item's displaymember property value is updated, the changes reflect back on the selected item of the list box . Why this issue? Just FYI: My View Model has properties EmployeeCollectionView and SelectedEmployeeId which are bound to combo as ItemsSource and SelectedValue resp. This VM implements the INotifyPropertyChanged interface. My core employee class (list of which is the source for the EmployeeCollectionView) is simply a Model class without INotifyPropertyChanged. DisplayMemberPath is "Name" property of employee Model class. I change this by some means and expect the combo selection box to update the value. I tried refreshing ther SelectedEmployeeId by setting it 0 (where it correctly selects the dummy "-- Select All --" employee entry from itemsSource) and old selected value back. But no use. The old value takes me back to the old label. Items collection has latest entry though. When I make combobox's IsEditable=True before the view's refresh and after refresh I make IsEditable=False then the things work out correctly! But this is a patch and is unnecessary. Thx Vinit Sankhe

  Read the article

• Access <body> tag properties from form found in mediaboxAdvanced lightbox.

  - by Christopher Richa

  I am building my portfolio website simply using HTML, Flash, and the Mootools Javascript framework. I have decided to implement a theme changing feature using Javascript and cookies. When the user clicks on the "Change Theme" link, a mediaboxAdvanced lightbox appears, containing a real-time form which allows you to change the theme on the portfolio. Here's the code for the form: <div id="mb_inline" style="display: none; margin:15px;"> <h3>Change Your Theme</h3> <form> <fieldset> <select id="background_color" name="background_color"> <option value="#dcf589">Original</option> <option value="#000FFF">Blue</option> <option value="#00FF00">Green</option> </select> </fieldset> </form> </div> I know, there is no submit button, but as soon as something is changed in that form, the following Mootools code happens: var themeChanger = new Class( { pageBody : null, themeOptions : null, initialize: function() { this.pageBody = $(document.body); this.themeOptions = $('background_color'); this.themeOptions.addEvent('change', this.change_theme.bindWithEvent(this)); }, change_theme: function(event) { alert("Hello"); } }); window.addEvent('domready', function() { var themeChanger_class = new themeChanger(); }); Now this is only a test function, which should be triggered when the dropdown menu changes. However, it seems that none of it works when the form is in the lightbox! Now if I decide to run the form outside of the lightbox, then it works great! Am I missing something? If you need more examples, I will fill in on demand. Thank you all in advance. -Christopher

  Read the article

• Regression Testing and Deployment Strategy

  - by user279516

  I'd like some advice on a deployment strategy. If a development team creates an extensive framework, and many (20-30) applications consume it, and the business would like application updates at least every 30 days, what is the best deployment strategy? The reason I ask is that there seems to be a lot of waste (and risk) in using an agile approach of deploying changes monthly, if 90% of the applications don't change. What I mean by this is that the framework can change during the month, and so can a few applications. Because the framework changed, all applications should be regression-tested. If, say, 10 of the applications don't change at all during the year, then those 10 applications are regression-tested EVERY MONTH, when they didn't have any feature changes or hot fixes. They had to be tested simply because the business is rolling updates every month. And the risk that is involved... if a mission-critical application is deployed, that takes a few weeks, and multiple departments, to test, is it realistic to expect to have to constantly regression-test this application? One option is to make any framework updates backward-compatible. While this would mean that applications don't need to change their code, they would still need to be tested because the underlying framework changed. And the risk involved is great; a constantly changing framework (and deploying this framework) means the mission-critical app can never just enjoy the same code base for a long time. These applications share the same database, hence the need for the constant testing. I'm aware of TDD and automated tests, but that doesn't exist at the moment. Any advice?

  Read the article

• What are some strategies for maintaining a common database schema with a team of developers and no D

  - by Mahmoud Abdelkader

  I'm curious about how others have approached the problem of maintaining and synchronizing database changes across many (10+) developers without a DBA? What I mean, basically, is that if someone wants to make a change to the database, what are some strategies to doing that? (i.e. I've created a 'Car' model and now I want to apply the appropriate DDL to the database, etc..) We're primarily a Python shop and our ORM is SQLAlchemy. Previously, we had written our models in such a way to create the models using our ORM, but we recently ditched this because: We couldn't track changes using the ORM The state of the ORM wasn't in sync with the database (e.g. lots of differences primarily related to indexes and unique constraints) There was no way to audit database changes unless the developer documented the database change via email to the team. Our solution to this problem was to basically have a "gatekeeper" individual who checks every change into the database and applies all accepted database changes to an accepted_db_changes.sql file, whereby the developers who need to make any database changes put their requests into a proposed_db_changes.sql file. We check this file in, and, when it's updated, we all apply the change to our personal database on our development machine. We don't create indexes or constraints on the models, they are applied explicitly on the database. I would like to know what are some strategies to maintain database schemas and if ours is seems reasonable. Thanks!

  Read the article

• Jquery if visible conditional not working

  - by Wade D Ouellet

  Hey, I have a page going here that uses jQuery: http://treethink.com/services What I am trying to do is, if a slide or sub-page is shown in there, change the background colour and colour of the button. To do this I tried saying, if a certain div is shown, the background colour of a certain button changes. However, you can see there that it isn't working properly, it is changing the colour for the web one but not removing the colour change and adding a colour change on a different button when you change pages. Here is the overall code: /* Hide all pages except for web */ $("#services #web-block").show(); $("#services #print-block").hide(); $("#services #branding-block").hide(); /* When a button is clicked, show that page and hide others */ $("#services #web-button").click(function() { $("#services #web-block").show(); $("#services #print-block").hide(); $("#services #branding-block").hide(); }); $("#services #print-button").click(function() { $("#services #print-block").show(); $("#services #web-block").hide(); $("#services #branding-block").hide(); }); $("#services #branding-button").click(function() { $("#services #branding-block").show(); $("#services #web-block").hide(); $("#services #print-block").hide(); }); /* If buttons are active, disable hovering */ if ($('#services #web-block').is(":visible")) { $("#services #web-button").css("background", "#444444"); $("#services #web-button").css("color", "#999999"); } if ($('#services #print-block').is(":visible")) { $("#services #print-button").css("background", "#444444"); $("#services #print-button").css("color", "#999999"); } if ($('#services #branding-block').is(":visible")) { $("#services #branding-button").css("background", "#444444"); $("#services #branding-button").css("color", "#999999"); } Thanks, Wade

  Read the article

• Calling AddEventListener in a loop with a variable element name

  - by user302209

  Hi, I'm trying to do the following: I have a set of images and select (dropdown) HTML elements, 30 of each one. I'm trying to use AddEventListener on a loop from 1 to 30 so that when I change the value of the select, the image src is updated (and the image changes). The AddEventListener function is this one: function AddEventListener(element, eventType, handler, capture) { if (element.addEventListener) element.addEventListener(eventType, handler, capture); else if (element.attachEvent) element.attachEvent("on" + eventType, handler); } I tried this and it worked: var urlfolderanimalimages = "http://localhost/animalimages/"; var testselect = "sel15"; var testimg = "i15"; AddEventListener(document.getElementById(testselect), "change", function(e) { document.getElementById(testimg).src = urlfolderanimalimages + document.getElementById(testselect).value; document.getElementById(testimg).style.display = 'inline'; if (e.preventDefault) e.preventDefault(); else e.returnResult = false; if (e.stopPropagation) e.stopPropagation(); else e.cancelBubble = true; }, false); But then I tried to call it in a loop and it doesn't work. The event is added, but when I change any select, it will update the last one (the image with id i30). var urlfolderanimalimages = "http://localhost/animalimages/"; for (k=1;k<=30;k++) { var idselect = "sel" + k; var idimage = "i" + k; AddEventListener(document.getElementById(idselect), "change", function(e) { document.getElementById(idimage).src = urlfolderanimalimages + document.getElementById(idselect).value; document.getElementById(idimage).style.display = 'inline'; if (e.preventDefault) e.preventDefault(); else e.returnResult = false; if (e.stopPropagation) e.stopPropagation(); else e.cancelBubble = true; }, false); } What am I doing wrong? I'm new to JavaScript (and programming in general), so sorry for the vomit-inducing code :(

  Read the article

• IIS error hosting WCF Data Service on shared web host

  - by jkohlhepp

  My client has a website hosted on a shared web server. I don't have access to IIS. I am trying to deploy a WCF Data Service onto his site. I am getting this error: IIS specified authentication schemes 'IntegratedWindowsAuthentication, Anonymous', but the binding only supports specification of exactly one authentication scheme. Valid authentication schemes are Digest, Negotiate, NTLM, Basic, or Anonymous. Change the IIS settings so that only a single authentication scheme is used. I have searched SO and other sites quite a bit but can't seem to find someone with my exact situation. I cannot change the IIS settings because this is a third party's server and it is a shared web server. So my only option is to change things in code or in the service config. My service config looks like this: <system.serviceModel xdt:Transform="Insert"> <serviceHostingEnvironment> <baseAddressPrefixFilters> <add prefix="http://www.somewebsite.com"/> </baseAddressPrefixFilters> </serviceHostingEnvironment> <bindings> <webHttpBinding> <binding name="{Binding Name}" > <security mode="None" /> </binding> </webHttpBinding> </bindings> <services> <service name="{Namespace to Service}"> <endpoint address="" binding="webHttpBinding" bindingConfiguration="{Binding Name}" contract="System.Data.Services.IRequestHandler"> </endpoint> </service> </services> </system.serviceModel> As you can see I tried to set the security mode to "None" but that didn't seem to help. What should I change to resolve this error?

  Read the article

• PHP Localization Best Practices? gettext?

  - by nute

  We are in the process of making our website international, allowing multiple languages. I've looked into php's "gettext" however, if I understand it right, I see a big flaw: If my webpage has let's say "Hello World" as a static text. I can put the string as <?php echo gettext("Hello World"); ?>, generate the po/mo files using a tool. Then I would give the file to a translator to work on. A few days later we want to change the text in English to say "Hello Small World"? Do I change the value in gettext? Do I create an english PO file and change it there? If you change the gettext it will consider it as a new string and you'll instantly loose the current translation ... It seems to me that gradually, the content of the php file will have old text everywhere. Or people translating might have to be told "when you see Hello World, instead, translate Hello Small World". I don't know I'm getting confused. In other programming languages, I've seen that they use keywords such as web.home.featured.HelloWorld. What is the best way to handle translations in PHP? Thanks

  Read the article

• how to synchronize application email to server email using java mail in android

  - by Akash

  i want to change synchronously change in email application then automatic change in server email. For example :- i have read the unread message on email application then automatic server email change unread mail to read mail. my email application has use mail jar file, activation.jar and additional jar file use and following code are use for connectivity email application to server email.. Properties props = System.getProperties(); props.setProperty("mail.store.protocol", "imaps"); props.put("mail.smtp.starttls.enable","true"); Authenticator auth = new Authenticator() { protected PasswordAuthentication getPasswordAuthentication(){ return new PasswordAuthentication("USEREMAILID","PASSWORD "); } }; sessioned= Session.getDefaultInstance(props, auth); store = sessioned.getStore("imaps"); // store.connect("imap.next.mail.yahoo.com","[email protected]","123456789"); store.connect("smtp.gmail.com","USEREMAILID","PASSWORD "); inbox = store.getFolder("inbox"); inbox.open(Folder.READ_ONLY); FlagTerm ft = new FlagTerm(new Flags(Flags.Flag.SEEN), false); UNReadmessages = inbox.search(ft);

  Read the article

• SSIS package not picking up configuration files correctly

  - by blntechie

  We have recently migrated some 30 DTS packages in SQL Server 2000 to SSIS packages in SQL Server 2008. We have created packages in such a way that all environment related variables and other required information are picked from configuration files for maintenance of packages across different environments like Dev, QA and Prod. After setting up all the packages with the config files, when we tested the packages from Business Intelligence Development Studio, it worked fine and picked up the values from the configuration file. And when changing the values in config files to Dev or other env it correctly picked up the values and executed. Similarly, tried for 2 different environments and the packages worked fine. So we deployed to Prod and it was working fine. Yesterday, I had to make a functional change for one package and so I made the change in the package (it is just changing a parameter in a SQL procedure execution task and not related to any variables) and tested in BIDS with 2 environments and it worked fine. As the change was not related to any environment change, we deployed only the updated package (not the associated config file) manually in Prod (i.e without the use of manifest). The config file which was used by the package previously and working fine in Prod remained unaltered. But when the package was executed, the package was pointing to QA and the package didn't read from the config file I believe. One reason may be, it is still using the last executed values which remains in the .dtsx file(can be checked by opening the file in a text editor) usually. But normally, when a package is executed, the values will be overwritten from config file. Guess it is not happening. What are the possible reasons for this? We have tested extensively switching between test environments and it does not show this behavior. We have encountered this in Prod environment twice now. Anyone else have experienced this and how have you resolved this?

  Read the article

• fill combobox value in datagridview based on other combobox in datagridview

  - by Purohit Raghu

  I m creating Web Application..in C# I have One Data grid view In that i Have 2 Combo box i m trying 2 bind second combo box based on first combo-box. in First Combo-box I have value Shirt,T shirt so i want if shirt is selected than second combo-box should have value Slim,Regular..and if T shirt Is selected than second Combo-box should have V neck and rounded color. i have different table for thirst and shirt type... I work fine for first time but when i goes on second row and change the combo box value than it will also change value of second combo box value of previous row as well .. Where i need to change to prevent change in upper row i have following code private void dataGridView1_EditingControlShowing(object sender, DataGridViewEditingControlShowingEventArgs e) { if (dataGridView1.CurrentCell.ColumnIndex == 0) { ComboBox cbx = e.Control as ComboBox; cbx.SelectionChangeCommitted -= new EventHandler(cbx_SelectionChangeCommitted); cbx.SelectionChangeCommitted += new EventHandler(cbx_SelectionChangeCommitted); } } private void cbx_SelectionChangeCommitted(object sender, EventArgs e) { int selectedIndex = ((ComboBox)sender).SelectedIndex; if (selectedIndex == 1) //this condition is true if i have selected shirt from combobox1 { ShirtType(); } if (selectedIndex == 2) { Tshirtype(); } } void ShirtType() { try { string str; str = "select ShirtType_name,ShirtType_Id from ShirtType_master"; ds = new DataSet(); ds = cn.readdata(str); Type.DataSource = ds.Tables[0];//Type is Combobox name of Second Combobox Type.DisplayMember = ds.Tables[0].Columns[0].ToString(); ; Type.ValueMember = ds.Tables[0].Columns[1].ToString(); ; } catch (Exception ee) { } } void Tshirtype() { try { string str; str = "select TShirtType_name,TshirtType_Id from TshirtType_Master"; ds = new DataSet(); ds = cn.readdata(str); Type.DataSource = ds.Tables[0]; Type.DisplayMember = ds.Tables[0].Columns[0].ToString(); ; Type.ValueMember = ds.Tables[0].Columns[1].ToString(); ; }

  Read the article

• .NET CF -- Set Form height based on InputPanel state

  - by user354941

  Hi, So, I've got a C# project for Windows Mobile phones and I'm trying to work with the InputPanel. Specifically, I've got one form with a stack of Labels and TextBoxes that collect user input. I have an InputPanel that alerts me when the user opens the SIP. Everything works fine so far. When I get messages that the SIP status has changed, I want to change the height of the Form, which doesn't seem possible. Here's my event handler for my InputPanel: void m_InputPanel_EnabledChanged(object sender, EventArgs e) { // :( this assignment operation doesn't work and it doesn't this.ClientSize = inputPanel1.VisibleDesktop.Size; // doesn't work this.Size = inputPanel1.VisibleDesktop.Size; // assignment operation works, but isn't very useful this.visibleHeight = inputPanel1.VisibleDesktop.Height; this.InitializeUI(); } When I say that the assignment operation doesn't work, I mean that the values don't change in the debugger. I can understand that maybe I can't change the size of a Form, but I can't understand why trying to change it wouldn't throw an exception, or give a compiler error. I have my Form WindowState set to Normal instead of Maximized, but it doesn't make a difference. Also, I have read http://www.christec.co.nz/blog/archives/42 this page that tells me how I'm supposed to do this, but I can't easily put all of my controls in a Panel because I'm using a bunch of custom stuff to do alpha background controls.

  Read the article

< Previous Page | 432 433 434 435 436 437 438 439 440 441 442 443  | Next Page >