Search Results

Search found 13451 results on 539 pages for 'physical environment'.

Page 439/539 | < Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >

• wireless clients not getting correct dhcp addresses

  - by szeli

  I apologise first if this is a stupid problem. I'm new to Cisco networking. I need some help with an existing configuration done by my vendor. Environment: 1. Core switch - Catalyst 6509e vlans configured: a. vlan 50 (wired clients) 10.0.50.x/24 interface IP 10.0.50.20 b. vlan 70 (wireless clients) 10.0.70.x/24 interface IP 10.0.70.20 c. vlan 192 (guest clients) 192.168.1.x/24 interface IP 192.168.1.20 d. trunk port for WLC native vlan 70 allowed vlan 50, 70, 192 2. Cisco 4402 WLC interfaces a. management untagged IP 10.0.70.10 b. ap-manager untagged IP 10.0.70.11 c. service-port n/a IP 192.168.10.1 d. virtual n/a IP 1.1.1.1 e. guestwlan vlan192 IP 192.168.1.100 3. Cisco AIR-LAP1142N-S-K9 LAP01 (WLAN local, interface: management) IP 10.0.70.21/24 GW 10.0.70.20 DHCP server 10.0.50.10 (scope 10.0.70.101 to 200) LAP02 (WLAN guest, interface: guestwlan) IP 192.168.1.21/24 GW 192.168.1.20 DHCP server 192.168.1.10 (scope 192.168.1.101 to 200) here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200) can anyone please help? thanks!

  Read the article

• How to start and stop a systemd unit with another?

  - by Andy Shinn

  I am using CoreOS to schedule systemd units with fleet. I have two units (firehose.service and firehose-announce.service. I am trying to get the firehose-announce.service to start and stop along with the firehose.service. Here is the unit file for firehose-announce.service: [Unit] Description=Firehose etcd announcer BindsTo=firehose@%i.service After=firehose@%i.service Requires=firehose@%i.service [Service] EnvironmentFile=/etc/environment TimeoutStartSec=30s ExecStartPre=/bin/sh -c 'sleep 1' ExecStart=/bin/sh -c "port=$(docker inspect -f '{{range $i, $e := .NetworkSettings.Ports }}{{$p := index $e 0}}{{$p.HostPort}}{{end}}' firehose-%i); echo -n \"Adding socket $COREOS_PRIVATE_IPV4:$port/tcp to /firehose/upstream/firehose-%i\"; while netstat -lnt | grep :$port >/dev/null; do etcdctl set /firehose/upstream/firehose-%i $COREOS_PRIVATE_IPV4:$port --ttl 300 >/dev/null; sleep 200; done" RestartSec=30s Restart=on-failure [X-Fleet] X-ConditionMachineOf=firehose@%i.service I am trying to use BindsTo with the notion that start and stop of firehose.service will also start or stop firehose-announce.service. But this never happens correctly. If firehose.service is stopped, then firehose-announce.service goes to failed state. But when I start firehose.service, the firehose-announce.service doesn't start up. What am I doing wrong here?

  Read the article

• What are secure ways of sharing a server (ssh+LAMP) with friends?

  - by Bran the Blessed

  What is the best way to share a virtual server with friends? More precisely, I have the following assets: A virtual private server (Debian Lenny) with root access for myself, running... SSH apache2 mysql Some unused disk space Some friends in need of hosting The problem I would now like to do the following: Hosting one or several domains per friend My friends should have full access to their domains, including running PHP scripts, for example My friends should not be able to poke around in other directories The security of my server should not be compromised by faulty PHP scripts To clarify: I do trust my friends in the sense that they are not trying to do something evil with their access. I just do not trust the programs they are going to run. So, what are your recommendations for establishing such a scenario? Partial solution I already came up with the following plan: Add chrooted SSH users for my friends Add Apache vhosts per user (point the directories to subdirectories of the homedirectories, i.e. /home/alice/example.com, /home/bob/example.net, etc. But how can I enforce a chroot-like environment for the scripts they are running within these vhosts? Any pointers would be appreciated.

  Read the article

• Confused with creating an ODBC connection, apparently I have two separate odbcad32.exe files?

  - by Hoser

  Alright, this is my first time working with this so forgive me if I'm a little confusing or vague. I have a server with Windows Server 2008 Standard without Hyper-v (6.0, Build 6002). I'm running a small website off this server and using a Microsoft Access database to store some information coming in through the website. I'm sure the PHP I have written to open the ODBC connection is correct as it has worked for me when I created this website in a testing environment on a laptop. My current issue now is that it seems like I have two different odbcad32.exe's, and one doesn't appear to have a driver for a .accdb file, and only a .mdb file. The other has a driver for both. The first one I speak of has a driver titled 'Driver do Microsoft Access (.mdb)', the second one has a driver titled 'Microsoft Access Driver (.mdb, .accdb)'. I access the first odbcad32.exe by going to C:\Windows\SysWOW64\odbcad32.exe, and then the one that seems to have the driver I need I go to Control Panel-Administrative Tools-Data Sources(ODBC) and simply create a new connection in the System DNS tab. Whenever I make changes to the one that I access through the Control Panel, I see no changes, however if I use the odbcad32.exe file in SysWOW64 I do get some changes in the errors that come back to me. The main difference I noticed is that when I set up an ODBC connection with the Control Panel method it said it simply couldn't find the ODBC connection, but when I made a .mdb connection in the SysWOW64 one (and pointed it to a .accdb file) it says Cannot open database '(unknown)'. It may not be a database that your application recognizes, or the file may be corrupt. Which makes it seem like it is this odbcad32.exe version in SySWOW64 that is being recognized as the 'correct' one. Is there any way to fix this? I've tried to be as thorough as possible but if I've been confusing or left anything out let me know.

  Read the article

• Minecraft server hosting hardware specifications [on hold]

  - by Andrew Wright

  I am planning on purchasing a server to rent off Minecraft game servers, largely to friends. I am planning on purchasing a 128GB RAM server to save on colocation costs (as I am likely to need more than 32GB and would have to rent 2U of space...) I am hoping for some advice about the processing power needed to deal with this level of RAM. The servers will be run in a shared environment on linux in a VM to make backups easier. The server I have in mind is dual CPU. I have been considering at the low end dual Xeon E5-2609V2 Quad-Core 2.5Ghz, and at the high end dual Xeon E5-2650V2 Eight-Core 2.6Ghz. The difference between these is 6.4 GT/s and 8 GT/s and £3000 for the lower spec server, £4300 for the higher spec. I was hoping I could get advice about whether it is worth paying for the extra/higher speed processor or if I would be wasting my money? Thank you for any help - I appreciate that this is not directly related to professional system administration.

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• Microsoft Word 2008 on the Mac sometimes "Disappears" documents, really.

  - by Ross Charette

  This happens in a computer lab environment, has happened at least 3 times. We are running Microsoft Office 2008 for mac on Leopard, everything is updated. Our user's home directories are on a network drive, but the /Library/Cache folder is running locally. Typically a student will have a Word file that they have been working on, it's been saved before they even logged onto the computer that day. They log on, open the document, click the save icon (not go to File Save), sometimes even save multiple times, then close Word. The document is now gone. It's not hidden, there are no autosaves or anything in the Cache folder. Definitely not in the trash or trashes folder. It can't find it when you click on it in 'recent documents'. Searching meticulously though every folder in their home drive turns up nothing. They look using Finder, I look ssh'd as root into their home using ls -la. I look for similar files in case they renamed it by mistake. It's gone. Disappeared. Vaporized. It's happened to at least 3 different users in the past year. Much whining. Any idea?

  Read the article

• Sharepoint web part fails intermittently

  - by pringly

  I have a MOSS 2007 environment, 2 web servers and a DB server, load balanced between the two web servers. I deployed a web part recently, which worked fine for a while, but failed on web server 2 after a day. When it fails, it gets the error message: 'A Web Part or Web Form Control on this Page cannot be displayed or imported. The type could not be found or it is not registered as safe’ Once it has failed, it will stay that way until an IIS reset is done. The other web server never fails, I tried to force the second web server to fail to recreate the issue and have been unable to do it. I tried placing it under heavy http traffic and it handled it fine. Put it back in the pool and it failed again after about 7 hours. So, if i remove the .dll for the webpart from the affected web server, the webpart doesnt stop working. Is this normal behavior? I checked the bin directory for the site and the global assembly and it there is no other copy of the .dll anywhere else on the server. Also, when checking the web part gallery, if the web part has failed it will appear in the gallery, but by trying to add a new webpart, the .dll wont be listed. I have no idea how to continue troubleshooting from here or even fix it, any ideas?

  Read the article

• Weblogic WLST classpath

  - by user43736

  When I run the WLST .sh script to set the env as follows why can't I see the updated path when I do echo? [linbox2 bin]$ ./setWLSEnv.sh CLASSPATH=/directory/ols_wls/patch_wlss1032/profiles/default/sys_manifest_classpath/weblogic_patch.jar: /directory/ols_wls/patch_wls1032/profiles/default/sys_manifest_classpath/weblogic_patch.jar: /directory/ols_wls/patch_oepe1032/profiles/default/sys_manifest_classpath/weblogic_patch.jar: /directory/ols_wls/patch_ocm1031/profiles/default/sys_manifest_classpath/weblogic_patch.jar: /directory/ols_wls/jrockit_160_14_R27.6.5-32/lib/tools.jar: /directory/ols_wls/utils/config/10.3/config-launch.jar: /directory/ols_wls/wlserver_10.3/server/lib/weblogic_sp.jar: /directory/ols_wls/wlserver_10.3/server/lib/weblogic.jar: /directory/ols_wls/modules/features/weblogic.server.modules_10.3.2.0.jar: /directory/ols_wls/wlserver_10.3/server/lib/webservices.jar: /directory/ols_wls/modules/org.apache.ant_1.7.0/lib/ant-all.jar: /directory/ols_wls/modules/net.sf.antcontrib_1.0.0.0_1-0b2/lib/ant-contrib.jar: PATH=/directory/ols_wls/wlserver_10.3/server/bin: /directory/ols_wls/modules/org.apache.ant_1.7.0/bin: /directory/ols_wls/jrockit_160_14_R27.6.5-32/jre/bin: /directory/ols_wls/jrockit_160_14_R27.6.5-32/bin: /usr/kerberos/bin: /usr/local/bin: /bin: /usr/bin: /usr/X11R6/bin: /usr/java/j2sdk1.4.2_11/bin/bin: /home/oracle/bin: /directory/wls_olwcs/jdk160_14_R27.6.5-32/bin: /directory/ccanywhere81/bin:/directory/oracle/oracle/product/10.2.0/client_1/bin Your environment has been set. [linbox2 bin]$ export CLASSPATH [linbox2 bin]$ export PATH [linbox2 bin]$ echo $PATH /usr/kerberos/bin: /usr/local/bin: /bin: /usr/bin: /usr/X11R6/bin: /usr/java/j2sdk1.4.2_11/bin/bin: /home/oracle/bin: /directory/wls_olwcs/jdk160_14_R27.6.5-32/bin: /directory/ccanywhere81/bin: /directory/oracle/oracle/product/10.2.0/client_1/bin [linbox2 bin]$

  Read the article

• How do I find and kill a php loop (process)?

  - by Hoytman

  I have a php script that I have been developing which calls an external api within a loop. It is being tested on a VPS which is running LAMP on Debian. I noticed this morning that the api was not responding to my script. When I called the provider, they told me that my server had been calling the api 1000's of times per hour for the past 10 hours. I am assuming that a php script (which I have been working on the day before and testing on my VPS) entered into an infinite loop during one of the executions, and never came out (I have been testing it from the command prompt, and not over the web.) I have attempted to stop and start Apache, but the api support staff says that the calls are still coming in from my server address. How can I find and stop the process? Also, is there a possibility that the Apache stop/start solved the problem, but the api is still trying to sort through past calls? Please forgive me for not using my local test environment correctly. Edit: I do not know the process name, I need to discover the name (or pid) based on behavior.

  Read the article

• Winodws server 2003 Setup

  - by Barracksbuilder

  I work at a university maintaining the computer science department server. I am looking for a more economical way to stream line the set up of student accounts. CS students are granted a Username and password an IIS virtual directory, FTP virtual directory, and a mysql database. Server is running windows server 2003R2 (Possibly migrating to 2008R2) The server is running a domain though no students physically log a terminal into it (No computers are part of my domain.) Creating the account is a manual process. I did right a PHP script to query the Universities AD and copy the information and write it to my AD. I then have to create basically the users home directory. I tried having AD do it but since the user never physically logs in it never creates the directory. Permissions on this folder are set to User - full, Instructors (group) - full, Users (group) - read, IUSER - read. Inside of the users folder their is a "Private" folder with permissions User - full, instructors (group) - full. Next step is IIS I create a virtual directory in the default web site pointed to the users home directory so they have a website. Same goes for FTP virtual directory in the default ftp configuration to allow the users to upload files to their website. Mysql I have to create a user and password then create a mysql scheme (database) full access for the user and full access to the instructors account to be able to access the students database. All of this is done manually and takes me a week to do. The closest description is maybe a shared hosting environment. Is there a better way to do this? Scripting wise, or better structure setup?

  Read the article

• Looking for a powershell script that can pull a file from a set of PC's and FTP

  - by DangeRuss

  I'm looking to write a script (preferably powershell) that will essentially copy a file from a bunch of PC's and FTP it to a server. So the structure of the environment is that we have a file on multiple PC's (around 50 or so) that need to placed on a server. Sometimes one of the PC's may be turned off so the script would first need to ensure the PC is up and running (maybe a ping result), then it would need to go into a directory on that PC, pull a file off of it, rename the file, place into a source directory, then remove the file. Naming convention doesn't matter, but date/time stamp would be easiest. Ideally, it would be best to first move all the files to a source directory to save on FTP bandwidth, but since the files will be named the same, the files must be renamed during the move process. Move not copy because the directory needs to be empty so the file can be re-created the next day. So once moved to the source directory, now all the files need to be FTP'd to a server for processing. After all of this, we need to know which PC's on the list did not respond so we can manually retrieve the file so the script should output a file (txt is fine) that will show which PC's were offline. Everything is one domain and script will be run from an server with admin creds. Thank you!

  Read the article

• Powershell Script to help archive company email

  - by sec_goat

  I am attempting to use powershell to gather emails that pertain to a certain subject, so that these correspondences might be turned over to a legal department. I am having a couple of issues here that I would like some assistance getting past. I run the following command: get-mailbox -Database "Mailbox Database" | Export-Mailbox -ContentKeywords "Keywords To Search" -TargetMailbox "sec_goat" -TargetFolder EmailSearch -StartDate "01/13/2011 12:01:00 This has pretty much done what I want, and returned a boat load of emails, however it has also flooded my inbox with hundreds of blank calendars and contact lists. I realize now I should have used the exclusion on these folders, as well as a test environment (which we don't have). 1.How can I clean up this script to not include all the blank folders, contacts and calendars that DO NOT match the keywords search? 2.How do I clean up hundreds of blank contact lists and calendars in my mailbox without right clicking and deleting each one? EDIT: I edited the post to change the scope of the question. I think my focus is less on the legal perspective and more on the "How can I clean up my mess and make future archives less messy and painful?"

  Read the article

• Printer spools but doesn't print

  - by DKNUCKLES

  I am having a bizarre issue with an end user who is unable to print to a USB attached printer. The environment is as Windows 7 machine with a Canon Pixma iP90 printer. The driver is installed (and has been re-installed several times), but whenever a print job is sent the printer spools but no printing ever occurs. The following is some relevant information I can confirm that the printer is spooling as the spool folder fills up, and the job "releases" and the spool folder empties I have turned off print spooling with no luck None of the features from the Canon utilities (ie Turn Printer Off) features work Computer recognizes the printer as being installed. When the cable is unplugged the printer icon grey's out in Devices and Printers Printer and cable are confirmed working as they work with other PC's in the office I have deleted the USB Root Hub devices and rebooted the machine with no luck No error messages are displayed or logged in the event viewer. The Canon diagnostics utility doesn't detect any problem and states the printer is functioning properly Printer is not shared User is able to print to other shared printers in the office Any help with this issue would be greatly appreciated.

  Read the article

• Server periodically freezing - Help Stabilizing

  - by JonDog

  We run an asp.net/sql server data collection website with a hand full of clients dumping data in and running reports. We moved to a new server (specs below) and have had issues with it freezing and having to reboot it a dozen times over the pass six months. The hosting company has mentioned possible causes (listed below) but cant give a definite answer on what is going wrong. They have offered to reconfigure how ever I like. We have benefited from having a much faster system and really dont want to get rid of the ssd's unless they are the issue. Two possible setup changes that I've talked with them about are also listed below. Any suggestions on what maybe causing the freezing issue as well as suggestion on a new setup would be great. My main questions are: Do SSD generally have problems running the OS & SQL Server on the same RAID Array? and Are the new SSD's still unrefined enough to be running in a production environment? Thanks Current: Xeon Quad Core E3-1270 3.40 Ghz 16 GB DDR3-1333 ECC SDRAM First Hard Drive: 120GB Intel SSD Second Hard Drive: 120GB Intel SSD Third Hard Drive: 120GB Intel SSD Fourth Hard Drive: 120GB Intel SSD SAS 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit MSSQL 2008 Web Edition Possible Causes: Running Sql Server & OS on same RAID Array OS Software Issues Using SSD's CPU Underpowered Not enough RAM Option 1 2x Xeon Quad Core E5-2603 1.80 GHz 16 GB DDR3-1333 ECC SDRAM 1 x 240GB Intel SSD - OS 3 x 1 TB SATA HDD (7200 RPM) - SQL Server SATA 4 Port RAID Card Windows 2012 Standard Edition - 64 Bit Option 2 Dell PowerEdge E3-1270v2 3.5GHz 4 Cores 16 GB DDR3-1600 UDIMM 4 x 128 GB Samsung 840 Pro SSD Add-in H200 (SAS/SATA Controller), 4 Hard Drives - RAID 10 Windows 2012 Standard Edition - 64 Bit

  Read the article

• What's the proper way to prepare chroot to recover a broken Linux installation?

  - by ~quack

  This question relates to questions that are asked often. The procedure is frequently mentioned or linked to offsite, but is not often clearly and correctly stated. In an objective to concentrate useful information in one place, this question seeks to provide a clear, correct reference for this procedure. What are the proper steps to prepare a chroot environment for a recovery procedure? In many situations, repairing a broken Linux installation is best done from within the installation. But if the system won't boot, how do you fix it from within? Let's assume you manage to boot into an alternate system. Once there, you need to access your broken installation in order to fix it. Many recovery How-Tos recommend using chroot in order to run programs as if you are actually booted into the broken installation. What is the basic procedure? Are there accepted best-practices to follow? What variables need to be considered in order to adapt the basic preparation steps to a particular recovery task? As this is Community Wiki, feel free to edit this question to improve it as well.

  Read the article

• Windows Server 2008 Alerting to Low memory

  - by t1nt1n

  I have a file and print server running on Windows 2008 R2 fully patched in a VSphere environment (ESXi 5.1 fully updated). Every evening between 19:20 and 19:30 our monitoring software reported that the available memory is 1% and performance is dire. There is nothing in the event logs to point to an issue. At this point in the evening I am general the only user on the system to check to see why these alerts are going off. Things I have done; Checked to see if any backups are running – None at all. Checked Scheduled tasks – None before or during this time period. Moved the VM to another host. AV is disabled to rule out that as the issue. The server does not have any problems during the day with memory when fully loaded with about 50 users. The server did have 4GB ram provisioned but I have increased this to 5Gb. Running PrefMon at the time (I will save the graphs tonight) There very little CPU usage at the time but RAM usage goes up.

  Read the article

• How do I get Tomcat 7 to start up faster in Linux CentOS kernel version 2.6.18?

  - by user1786833

  I am experiencing a problem with slow start up times for Tomcat 7. I have done some testing by tweaking configuration parameters both on Linux CentOS kernel version 2.6.18 and on Windows 7 using this link as my primary guide: http://wiki.apache.org/tomcat/HowTo/FasterStartUp and managed only a modest improvement. The improvements seemed to result when I added metadata-complete="true" attribute to the element of my WEB-INF/web.xml file and when I added the names of almost all the jars we use for our application to the tomcat.util.scan.DefaultJarScanner.jarsToSkip property in conf/catalina.properties file. I've also used this JAVA_OPTS in the setenv.sh file: JAVA_OPTS="$JAVA_OPTS -server -Xms1536m -Xmx1536m -XX:MaxPermSize=256m -XX:NewRatio=2 -XX:+UseParallelGC -XX:ParallelGCThreads=2 -Dsun.rmi.dgc.client.gcInterval=1800000 -Dsun.rmi.dgc.server.gcInterval=1800000 -Dorg.apache.jasper.runtime.BodyContentImpl.LIMIT_BUFFER=true " but actually saw my start up times increase slightly. Our QA and production environments are on Linux CentOS so I'm hoping to get more information on improving Tomcat 7 start up times in that environment. My primary role is java developer and I don't have much system administration experience so I appreciate any input. Thank you for your time and suggestions.

  Read the article

• Windows 7 host with Ubuntu Guest and a performance hit, memory locks?

  - by Cyrylski

  I have a brand new Lenovo T510 with Core i5 and 4GB of RAM with Windows 7 on it. I Installed Ubuntu 10.10 in a Virtualbox. For some reason system gets really slow on this setup which makes me really angry. There's a video card shared with full 3D support enabled and 1GB of RAM allocated for the Ubuntu machine. It may sound stupid, but WHY is the whole memory consumed in an instant when I run Virtualbox? I struggled for like 10 minutes restraining myself from a brutal reset, and now everything runs smooth but memory "in use" in Resource Monitor is 3GB flat with only Chrome running. I'm new to Windows 7, but I'm really disappointed with performance at this point... I used to work in a different environment with much slower hardware and there was no such problem (WinXP over Ubuntu, 1GB out of 2GB allocated for WinXP guest on intel GMA). This is, until I clogged RAM totally there. But I was capable of running Chrome, Firefox and Apache server on a 1GB RAM in Ubuntu there and Photoshop CS4 on Windows XP and it worked. In this case I can't go beyond setting up Ubuntu properly. I bet I'm doing something wrong.

  Read the article

• Sudo won't execute command as another user

  - by TOdorus

  I'm trying to get a unicorn server to start when the server boots. I've created a shell script which works if I log as the ubuntu user and run /etc/init.d/unicorn start Shell script #!/bin/sh case "$1" in start) cd /home/ubuntu/projects/asbest/current/ unicorn_rails -c /home/ubuntu/projects/asbest/current/config/unicorn.rb -D -E production ;; stop) if ps aux | awk '{print $2 }' | grep `cat ~/projects/asbest/current/tmp/pids/unicorn.pid`> /dev/null; then kill `cat ~/projects/asbest/current/tmp/pids/uni$ ;; restart) $0 stop $0 start ;; esac When I rebooted the server I noticed that the unicorn server wasn't listening to a socket. Since I ran the code succesfully as the ubuntu user I modified the script to let it always use the ubuntu user via sudo. #!/bin/sh case "$1" in start) cd /home/ubuntu/projects/asbest/current/ sudo -u ubuntu unicorn_rails -c /home/ubuntu/projects/asbest/current/config/unicorn.rb -D -E production ;; stop) if ps aux | awk '{print $2 }' | grep `cat ~/projects/asbest/current/tmp/pids/unicorn.pid`> /dev/null; then sudo -u ubuntu kill `cat ~/projects/asbest/current/tmp/pids/uni$ ;; restart) $0 stop $0 start ;; esac After rebooting unicorn still wouldn't start, so I tried running the script from the command line. Now I get the following error sudo: unicorn_rails: command not found I've searched high and low to what could cause this, but I'm afraid I've tapped my limited understanding of Linux. From what I can understand is that although sudo should use the ubuntu user to execute the commands, it still uses the environment of the root user, which isn't configured to run ruby or unicorn. Does anybody have any experience with this?

  Read the article

• Using Monit to monitor Resque

  - by Alex

  I'm trying to use resque as a job runner for Rails. I've tried this config, and many other ways of demonizing the rescue task (because running rake resque:work leaves the terminal tied to that command). Unfortunately, their example configuration doesn't work for me. Does the configuration look correct? Or is there another way to turn the process into a daemon? Thank you :) check process resque_worker_QUEUE with pidfile /data/APP_NAME/current/tmp/pids/resque_worker_QUEUE.pid start program = "/bin/sh -c 'cd /data/APP_NAME/current; RAILS_ENV=production QUEUE=queue_name VERBOSE=1 nohup rake environment resque:work& > log/resque_worker_QUEUE.log && echo $! > tmp/pids/resque_worker_QUEUE.pid'" as uid deploy and gid deploy stop program = "/bin/sh -c 'cd /data/APP_NAME/current && kill -s QUIT `cat tmp/pids/resque_worker_QUEUE.pid` && rm -f tmp/pids/resque_worker_QUEUE.pid; exit 0;'" if totalmem is greater than 300 MB for 10 cycles then restart # eating up memory?

  Read the article

• How to decouple development server from Internet?

  - by intoxicated.roamer

  I am working in a small set-up where there are 4 developers (might grow to 6 or 8 in cuople of years). I want to set-up an environment in which developers get an internet access but can not share any data from the company on internet. I have thought of the following plan: Set-up a centralized git server (Debian). The server will have an internet access. A developer will only have git account on that server, and won't have any other account on it. Do not give internet access to developer's individual machine (Windows XP/Windows 7). Run a virtual machine (any multi-user OS) on the centralized server (the same one on which git is hosted). Developer will have an account on this virtual machine. He/she can access internet via this virtual machine. Any data-movement between this virtual machine and underlying server, as well as any of the developer's machine, is prohibited. All developers require USB port on their local machine, so that they can burn their code into a microcontroller. This port will be made available only to associated software that dumps the code in a microcontroller (MPLAB in current case). All other softwares will be prohibited from accessing the port. As more developers get added, providing internet support for them will become difficult with this plan as it will slow down the virtual machine running on the server. Can anyone suggest an alternative ? Are there any obvious flaws in the above plan ? Some key details of the server are as below: 1) OS:Debian 2) RAM: 8GB 3) CPU: Intel Xeon E3-1220v2 4C/4T

  Read the article

• Monitoring Between EC2 Regions

  - by ABrown

  I'm working on a small EC2 project that involves a handful of servers in two different regions (US East and EU West). My first task is to implement a Nagios monitoring solution. Monitoring within a region is simple - I just use the private domain names/IPs, but I'm a little unsure of the best way to handle monitoring the second region without setting up a second Nagios install. The environment is fairly static, so I'm not going to be scripting the configuration with the EC2 tools just yet. As I see it, I have two options. Two Nagios installations (which is over-kill for the small number of servers I'm dealing with). Pros: I don't have to alter the group permissions nor do I have to pay for the traffic, redundancy in the monitoring solution - I could monitor the Nagios servers. Cons: two installations to deal with and I'd need to run another server instance. Have the single installation monitor both regions. Pros: one installation to deal with. Cons: slightly reduced security - security group will have to have NRPE (5666) opened for one source IP and also paying for a small amount of bandwidth at the Internet rate for data transfer between the regions. I guess my question is - how have others handled this problem and what are your recommendations? Thanks!

  Read the article

• Automatic switching of network card when vm is moved

  - by spock

  I have two hosts in a pool and I used to be able to move the vm around and they will start without any problem. But after I played around with some network setting, which I don't remember what, I started getting "This VM needs storage that cannot be seen from that server" message. As you can tell I am a beginner with Xenserver. Here is the very simple environment: 2 host servers with their own local hard disk and network card. One is a Pool master. Problem: Power off a vm and move vm from one server to another, or clone one vm to the other server. It used to be able to start up right away. Now, I need to delete one of the network that does not belong to the server, then it will start. Otherwise, the above error msg popup. The two networks (one for each network card in each host) are in the Networking tab of the vm, as well as in the host's networking tab. I googled but all I got to empty the DVD drive, which is not the problem here. Thanks in advance!

  Read the article

• How can I assign DHCP leases from a script?

  - by devicenull

  I have an environment where there is one DHCP server servicing a number of different hosts/vlans. The switches are configured to forward the DHCP requests over (via ip-helper) and include information about the port (option 82). I'd like to take that information and translate it into an actual lease for the server. I don't think it's particularly feasible for me to pregenerate a list of available leases, but I should be able to determine an address for a lease as it comes in. Is there an DHCP server that can execute a script when it receives a request? (Note: I'm looking to assign the IP from the script, not have the DHCP server assign an IP then execute the script) Edit: So, ultimately I'm trying to provide DHCP/PXE services over a large number of distinct vlans. This is so we can do OS installs via PXE booting without having to have a separate PXE vlan. I've got the switch config down no problem, and I have the DHCP server recognizing option 82. I need a way to pull DHCP assignments from another system (this other system would know what subnet to use on what vlan), but I do not want to have to pregenerate a list of vlan:DHCP range pairs.

  Read the article

< Previous Page | 435 436 437 438 439 440 441 442 443 444 445 446  | Next Page >