Search Results

Search found 1493 results on 60 pages for 'cycle'.

Page 44/60 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Very different results from df after a few seconds

  - by tatus2

  When the backup moves the files from one server to the other the results from df change every few seconds in an impossible manner. The source host is running rsync. On the destination host I'm running the following command every few seconds: echo `date` `df|grep md0` Results are below: Sat Jun 29 23:57:12 CEST 2013 /dev/md0 4326425568 579316100 3527339636 15% /MD0 Sat Jun 29 23:57:14 CEST 2013 /dev/md0 4326425568 852513700 3254142036 21% /MD0 Sat Jun 29 23:57:15 CEST 2013 /dev/md0 4326425568 969970340 3136685396 24% /MD0 Sat Jun 29 23:57:17 CEST 2013 /dev/md0 4326425568 1255222180 2851433556 31% /MD0 Sat Jun 29 23:57:20 CEST 2013 /dev/md0 4326425568 1276006720 2830649016 32% /MD0 Sat Jun 29 23:57:24 CEST 2013 /dev/md0 4326425568 1355440016 2751215720 34% /MD0 Sat Jun 29 23:57:26 CEST 2013 /dev/md0 4326425568 1425090960 2681564776 35% /MD0 Sat Jun 29 23:57:27 CEST 2013 /dev/md0 4326425568 1474601872 2632053864 36% /MD0 Sat Jun 29 23:57:28 CEST 2013 /dev/md0 4326425568 1493627384 2613028352 37% /MD0 Sat Jun 29 23:57:32 CEST 2013 /dev/md0 4326425568 615934400 3490721336 15% /MD0 Sat Jun 29 23:57:33 CEST 2013 /dev/md0 4326425568 636071360 3470584376 16% /MD0 As you can see I start from USE of 15% and after 15 seconds I'm at 37% (I don't need to mention that the backup can not copy this huge amount of data in such a short time). After ~20 seconds the cycle closes. I'm again roughly at the same usage as earlier. The value is reasonable, ca. 35 Mb were copied. Can somebody explain to me what is going on? Does df only make an estimation of usage instead of used value?

  Read the article

• Why would my wireless cut in and out every minute or so?

  - by Strilanc

  I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

  Read the article

• Switching between taskbar tasks sequentially

  - by Doug Kavendek

  In Firefox and some other tabbed interfaces, I can use Ctrl-PgUp/Down to cycle through tabs sequentially, based on their order in the tab list. I associate what is what based almost entirely on its position along the tab bar and what is next to what, so this is extremely useful for the way I keep track of things in my head. However, I haven't been able to find an equivalent for actual taskbar items in Windows, such that with a single shortcut will switch focus to the task item either to the left or the right of the current task in focus. There's a lot of existing shortcuts that I use (Alt-Tab, Ctrl-Esc, and their counterparts), but these use the window manager's stacking order, so it always changes based on what you've switched between in the past, and so their usefulness generally only lies in switching between two apps -- above that, I just can't keep that kind of stack in my head. The closest shortcut I've found is Winlogo-Tab, but it only moves a selector on the taskbar, so you have to hit space after moving it, and it also seems to originate the selector from the leftmost item every time (rather than relative to the current item). Am I just a weirdo and will have to write my own app to perform these actions?

  Read the article

• Whats the easiest route to trying out mono 2.6?

  - by E J

  We have several web applications built on Microsoft technologies (asp.net+mvc framework, built using VS2008, MS SQL Server). I have recently be playing with Ubuntu (9.10), installed using Wubi, and wanted to see if I can get our apps running on a foss software stack. I have got the hang of the very basics of Postgresql and I have read that there is some support for Linq to SQL in mono (as of 2.6) as well as asp.net/MVC. However I am unsure how to go about getting Mono 2.6 up and running. Here is what I have discovered so far: Ubuntu is not meant for the 'cutting edge' it is designed to be stable hence, it sometimes takes a release cycle or two for new software to make it to the repositories Mono is already installed by default, but it is likely to stay at version 2.4 for at least the 10.4 release You can install paralell environments of Mono, if you know what your doing. I have had a go at setting up parallel environments, but haven't had any luck yet. (And TBH I am not certain that that will do what I think it's gonna do). (tl;dr start here) Is there a distribution of Linux similar enough to Ubuntu, that I wouldn't have to start the learning curve all over again, but that will let me install Mono 2.6, Postgresql, (and possibly mono-develop 2.4)? Or should I persist with Ubuntu?

  Read the article

• SQL Server log backups "stalling"

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• How to organize deployment process in Chef-controlled environment?

  - by Alex

  I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

  Read the article

• Dual-booting Windows 7 and Ubuntu

  - by CFP

  Hello everyone, I've just received my Dell Studio 17 laptop, which comes with Windows 7 x64 preinstalled. I'm having quite a hard time installing ubuntu on it. First of all, here is how I partitioned the drive using GPartEd: |==Dell utility partition==|==Dell Recovery partition==|==Windows 7==|[==Ubuntu==|==Data partition==]| Where [] denotes an extended partition. Here are the steps I completed: I used GParted to create this structure, keeping windows 7 installed I booted ubuntu LiveCD, and installed it on the right partition I let it install grub automatically I rebooted intu ubuntu I went back to windows 7, no problems I then rebooted. Grub was gone. I used Super Grub Disk to restore grub, it didn't work. I tried to boot into ubuntu from supergrubdisk, but grub couldn't fint the boot folder I then reinstalled ubuntu, went through the same steps, but there SGD did boot my ubuntu I reverted to the previous version of grub, and installed it on my hard drive It worked, but trying to boot win7 got me the "No MBR, press Ctrl+Alt+Del to reboot" error I used the windows 7 cd to restore the MBR (the auto wizard didn't work, had to rebuild the mbr from command line Now Ubuntu is gone. 7 works fine I read a lot about this, and realized that many people could simply not boot win7 again after encountering this problem. Now I'd like to restore GRUB, but I really won't go through the hassle of doing a full new cycle of installing/reinstalling everything again. Is there a GRUB guru around, to provide me with a detailed guide to not screwing everything up once again? Thanks a lot!

  Read the article

• Upgrade Centos 5 tot PHP 5.2 or 5.3 [recommended way?]

  - by solid

  We are using Zend Framework and in version 2, php 5.2 will be the minimum requirement. We love CentOS and we'd like to keep using it, but PHP 5.1 just won't do anymore when developing web applications with Zend framework. I found several links to solutions to upgrade with external repositories. http://serverfault.com/questions/106801/recommended-method-to-upgrade-php-5-1-6-to-5-2-x-on-centos-5 http://www.webtatic.com/blog/2009/05/installing-php-526-on-centos-5/ http://www.webtatic.com/blog/2009/06/php-530-on-centos-5/ We'd like to see another solution with the use of an "official?" CentOS repository if any is available. We only need to upgrade PHP, the rest of the CentOS setup is fine the way it is. For us, it's important however to keep the YUM cycle intact using the normal repositories. So in short: is it even possible to upgrade only PHP by using an external repo or otherwise? While still upgrading all our other packages safely through normal yum usage? Thanks for your help!

  Read the article

• Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

  - by cjavapro

  At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

  Read the article

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Would an array of SSD drives be able to succesfully substitute the system memory?

  - by Florin Mircea

  I watched a few videos trying to answer this. This video (youtube.com/watch?v=eULFf6F5Ri8) shows a bunch of guys stacking 24 SSD's reaching a peak of around 2GBps r/w. That's under the limit of the worst DDR3 in this list (memorybenchmark.net/write_ddr3_amd.html) - that shows DDR3 memory performance varying from 2.78 to 6.55 Gb per second, but that video is over 3 years old. This video (youtube.com/watch?v=27GmBzQWwP0) shows a more optimistic situation, but for PCI-E SSD drives: 5 drives peaking at around 4Gb. And this other video shows that stacking up more than 3 SSD's doesn't realistically offer a substantial added performance. This and the fact that in all benchmarks the drives act quite poorly when dealing with small files (5k file read/write averaging from 10MB to around 30-40MBps) as opposed to how native memory handles such files, seems to indicate a definite NO to this question. Also, the write life cycle is indeed limited and the drives might wear out quickly, as kindly pointed out by paddy. However, I wanted to get more opinions on this. Would it be possible to at least obtain current memory performance with SSD's in RAID 0? And if so, in what circumstances? I am assuming using this configuration with a Windows OS that has a memory pagefile resident to that stack of SSD's, thus making it very fast to work with.

  Read the article

• Need help toubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

  Read the article

• Log backups "stalling" on SQL 2008?

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• nginx logrotate config

  - by TomOP

  Whats the best way to rotate nginx logfiles? In my opinion, I should create a file "nginx" in /etc/logrotate.d/ and fill it with the following code and do a /etc/init.d/syslog restart after that. This would be my config (I havn't tested it yet): /usr/local/nginx/logs/*.log { #rotate the logfile(s) daily daily # adds extension like YYYYMMDD instead of simply adding a number dateext # If log file is missing, go on to next one without issuing an error msg missingok # Save logfiles for the last 49 days rotate 49 # Old versions of log files are compressed with gzip compress # Postpone compression of the previous log file to the next rotation cycle delaycompress # Do not rotate the log if it is empty notifempty # create mode owner group create 644 nginx nginx #after logfile is rotated and nginx.pid exists, send the USR1 signal postrotate [ ! -f /usr/local/nginx/logs/nginx.pid ] || kill -USR1 `cat /usr/local/nginx/logs/nginx.pid` endscript } I have both the access.log and error.log files in /usr/local/nginx/logs/ and want to rotate both daily. Can anyone please tell me if "dateext" is correct? I want the log filename to be something like "access.log-2010-12-04". One more thing: Can I do the log rotation every day on a specific time (e.g. 11 pm)? If so, how? Thanks.

  Read the article

• Win7 Hangs During App Install/Upgrade/Uninstall

  - by JadeMason

  I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

  Read the article

• SQL Server log backups “stalling”

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Hard Disk based storage library

  - by Ryan M.

  We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

  Read the article

• Need help ttoubleshooting PC

  - by brux

  I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

  Read the article

• How to Monitor Network in Medium-Sized Company?

  - by Kyle Lowry

  I work at a medium sized company (100+ employees). An issue that has been cropping up is network performance, internet access in particular. We have about 70 or more computers, a mix of Mac OS X and Windows XP & 7 machines. We have several servers (Exchange server, PC file servers, MS SQL, Blackberry, FTP, Mac server, etc). There are four main switches, a SonicWall firewall, and probably a couple routers in the server room with a dozen or so more scattered around the building. The network structure has grown organically over a number of years; and, as far as I know, there really isn't a monitoring solution in place. When we experience network issues (slow connections, dropped packets, and so on), our general solution is to power cycle some hardware or go around to each employee and ask them if they are uploading/downloading any large files. This is really inefficient and time consuming, and it does not allow us to monitor the network, tackling potential problems proactively. I would like to find a solution that would allow me to monitor network usage company-wide in real time, with detail going down to the individual computer, ideally. Given the hodgepodge of equipment and operating systems, what would be the best way to set up some kind of monitoring solution? Hardware, software, restructuring our network architecture?

  Read the article

• Puppet: is it ok to "force" certname when you expect to shuffle nodes around?

  - by Luke404

  We all know (good example on SF) that Puppet hostname detection could be... fun. At our company (and I guess we're not alone at this) we usually pre-configure servers at our offices and test them before bringing the gear to a remote datacenter and rack them. Of course the reverse dns will change when doing that, even if we don't change the actual hostname of the system. We're slowly drafting our puppet setup and I'd like to be sure those moves won't create problems. My idea is to explicitly configure the desired full FQDN of the system as certname in puppet.conf at server provision time (before the very first puppet run). My process would look something like this: basic o.s. installation basic network configuration, enough to reach the internet and resolve dns install puppet and set up certname start puppet and let him manage the whole configuration test, fix problems in config (via puppet), re-test, and so on... manually stop puppet set up new network configuration for the datacenter network move the machine to DC turn it on puppet should automatically start and keep on doing its job The process is supported by detecting the environment in puppet's manifests (eg. based on subnet, like they do at Wikimedia) and modify configuration as needed (eg. resolv.conf contents appropriate for each network). Each node's certname will never change for the whole system life cycle. Is there any problem with this approach? Could it be improved?

  Read the article

• nginx logrotate config

  - by TomOP

  Whats the best way to rotate nginx logfiles? In my opinion, I should create a file "nginx" in /etc/logrotate.d/ and fill it with the following code and do a /etc/init.d/syslog restart after that. This would be my config (I havn't tested it yet): /usr/local/nginx/logs/*.log { #rotate the logfile(s) daily daily # adds extension like YYYYMMDD instead of simply adding a number dateext # If log file is missing, go on to next one without issuing an error msg missingok # Save logfiles for the last 49 days rotate 49 # Old versions of log files are compressed with gzip compress # Postpone compression of the previous log file to the next rotation cycle delaycompress # Do not rotate the log if it is empty notifempty # create mode owner group create 644 nginx nginx #after logfile is rotated and nginx.pid exists, send the USR1 signal postrotate [ ! -f /usr/local/nginx/logs/nginx.pid ] || kill -USR1 `cat /usr/local/nginx/logs/nginx.pid` endscript } I have both the access.log and error.log files in /usr/local/nginx/logs/ and want to rotate both daily. Can anyone please tell me if "dateext" is correct? I want the log filename to be something like "access.log-2010-12-04". One more thing: Can I do the log rotation every day on a specific time (e.g. 11 pm)? If so, how? Thanks.

  Read the article

• Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

  - by bob-the-destroyer

  Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

  Read the article

• My scanner isn't responding. It is connected to a SCSI interface using Windows XP

  - by Bob

  I have a Microtek ScanMaker 9600XL scanner. The best part about it is that it is 12x17 inches. Wowza! The worst part about it is that I've had it working at one point, with the same cable, same card, same computer, but have since re-installed Windows XP on it. Currently it will turn on, and blink the Power and Ready lights. They should be solid. I've done my best to find documentation for this, but all I've really gotten is the content on the Microtek site. I've tried turning the scanner on, then the PC. Turning the PC on, then the scanner. When I try launching the software it pops up a dialog saying "ScanWizard Pro can't find any scanners! Use SCSI Check to find a scanner." I know the scanner has a pair of little buttons on the back. These cycle up/down a counter. I think it goes 0-7. Any thoughts on what that does, or how to proceed troubleshooting? I think my next step is to try each of those numbers, and do both pc booted first, and scanner booted first for each of those numbers...

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >