Search Results

Search found 3461 results on 139 pages for 'drives'.

Page 44/139 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• Why can't I access the WebUI of my DNS-323 NAS after a firmware upgrade?

  - by anonymous2

  Hi Everyone, I just bought a D-Link DNS-323 NAS Enclosure, and have run into a problem. I read that the firmware that had shipped with (1.07) did not support 2TB drives, so I downloaded firmware 1.08. Turned on the device for thwe first time and went straight to the WebUI (everything looked/worked fine) Proceeded with the firmware update, completed successfully. Rebooted and I cannot access the WebUI. I can see the NAS connected via my router interface I can also ping the ip adress assigned, but I cannot access the WebUI or find it via D-Link easy search software. I have tried the factory reset button, but that does not seem to be doing anything, the square blue light just keeps flashing from the moment the unit is powered on, whether I press the reset button or not, and the symptoms remain the same... PS. I did/do not have any drives installed yet. Please help?

  Read the article

• ESXi onboard SATA passthrough [on hold]

  - by lodge93

  I am running ESXi 5.5 on a home system. When I attempt to pass one of the onboard SATA controllers (Intel ICH10R) to a VM, it is successful. However, the controller never appears in the VM. What else am I missing that would cause a VM to not recognize the controller? Additional Info: The controller is set to AHCI mode in the BIOS Prior to setting up the controller for passthrough, ESXi did recognize the controller and the drives I have tried with multiple VMs, none of which recognized the controller or the attached drives I have two onboard SATA controllers, on controller for ESXi and one for passthrough The final ideal state is that I could passthrough the controller to a FreeNAS VM

  Read the article

• Defrag/TRIM settings for hybrid hard drive?

  - by Joel Coehoorn

  I recently acquired a momentus XT hybrid hard drive. This is a tradition spinning HDD with a small SSD portion for frequently used files. Normally, you are not supposed to defrag SSDs, as it does not help performance and can significantly reduce the life of the drive. But you do need to defrag an HDD to keep good performance. So where does that leave us for hybrid drives? Do I need to turn off defragging in Windows to preserve the SSD portion? Is the on-disk controller smart enough to handle defragging correctly? Is there some utility I need to set it up that I missed? Additionally, for SSDs you normally want to check for and enable TRIM support... but this makes no sense for a HDDs. Where does that leave us for hybrid drives? Should I try to enable TRIM or not?

  Read the article

• Economical way to get many harddrives into rack mount?

  - by Industrial

  Hi everyone, Please bear with me as being a bit of a newcomer at 19" rack-mounted equipment. I've thought a fair bit lately about the best way of getting 4x or 6x of 2.5" hard drives into my rack and are right now currently slightly confused about would be the best (economical) solution. After scouting the market, I've found this type of disk array units that offers built in RAID and a lot of drive slots and a truckload of geek cred, but at a price that just isn't going to fit in my budget. I've also found these type of cute adapters that takes two 2.5" drives in one 3.5" slot, but I will obviously need a chassie with a lot of 3.5" spaces in order to make it work. So what is the most economical way to house my harddrives in my rack?

  Read the article

• Installed Ubuntu 11.10, getting hard disk health warnings

  - by Brad

  I'm getting hard disk health problem warnings... When I click the "examine" button the disk utility pops up. None of my drives are reporting any major issues, and the very first drive doesn't even have a SMART button. I don't really care if one of the drives is crashing, I've got everything backed up, but I just want to know how to stop these god forsaken message boxes from popping up randomly. I have already gone into the Disk Utility and checked "do not notify me if this drive is failing" on all of them except the one that doesn't have the SMART button. I've googled about as much as I can for one day.

  Read the article

• Which motherboard for Intel i7 and how to get RAID working?

  - by jasondavis

  I am wanting to build a new PC, I have a couple questions. 1) I am wanting to go with the Intel Core i7 920 Processor, can anyone reccomend a good reliable motherboard for this processor? Graphics card support does not matter (sli-crossfire). I would like to support a lot of ram, so the more ram slots the better. I have read so many bad reviews about certain boards not working good, I would love recommendation from experience. 2) I am wanting to run a couple SSD drives in RAID-0, I have never done this, will I need to purchase anything additional to the MB and CPU and drives to get raid working?

  Read the article

• Most efficient RAID configuration with 6 disks?

  - by Bob King

  I have a hand-me-down server that I'm setting up at home and it's got 6 72Gb hard disks (as well as 2 18Gb drives that I'm using for the OS). What is the best way to configure those 6 drives? Should I RAID 5 or 6, or go with something simpler, like mirroring? I'm planning to use it to hold a source control repository, and possibly data for a development SQL server. The machine has a hardware raid controller. It is an old IBM server.

  Read the article

• Readyboost on Windows 7 x64

  - by RobLaw84

  I'm thinking of bying 1 or more flash drives or an SD card to use with the readyboost function on by 64bit Windows 7 machine. I have a few questions regarding it before i put my hand in my pocket and buy anything. If i go ahead I would be using the fastest available flash/SD. I have 6GB of RAM current installed so will readyboost make any difference to boot / program load times? Will 2 x 2GB flash drives be quicker than 1 x 4GB or is the limitation on the motherboard? Would an SD card better than USB flash drive? thanks

  Read the article

• What's a worthwhile test for a new HD?

  - by Michael Kohne

  I work for a company that uses standard 2.5" SATA HD's in our product. We presently test them by running the Linux 'badblocks -w' command on them when we get them - but they are 160 gig drives, so that takes like 5 hours (we boot parted magic onto a PC to do the scan). We don't actually build that many systems at a time, so this doable, but seriously annoying. Is there any research or anecdotal evidence on what a good incoming test for a hard drive should be? I'm thinking that we should just wipe them with all zeros, write out our image, and do a full drive read back. That would end up being only about 1 hour 45 minutes total. Given that drives do block remapping on their own, would what I've proposed show up any infant mortality just as well as running badblocks?

  Read the article

• Windows 2008 Best Raid Configuration

  - by Brandon Wilson

  I have 4 2TB hard drives and I was thinking about using Raid 10. This would give me 4TB correct? My next question is would it be easy to add more hard drives to the raid array. For example if I bought another hard drive can I add it to the array without backing up any data? Basically I want to be able to start off with 4TB and when the space becomes full add more space as needed. If this isn't possible with Raid 10, is it possible with any Raid configuration. Any suggestions would be appreciated. Thank you.

  Read the article

• Three disk (possibly RAID) data recovery

  - by Martin

  I have on my desk three 160 GB disks that were once part of an HP Proliant Windows 2003 Server. They may have been part of a RAID configuration of some sort. They may or may not be damaged in some way. When I interface them via USB, one of them shows up as a drive, but unformatted. The others show up as uninitialized disks in manager. An alternative explanation is that the two drives were simply not unused. What's my first step? I've recovered data off damaged drives before but never had anything to do with RAID configs. How can I even tell if any type of RAID was used?

  Read the article

• HP MSA 1000 SAN: Can I use 1 array/shelf?

  - by CC

  Hi all, I'm planning some expansion on an HP MSA1000 SAN. My boss says that we need to have two separate arrays on the new enclosure, one for Bays 1-7, the other for Bays 8-14. Is there any reason that we need to do this? My plan was to have the entire expansion shelf be 1 array, then create RAID 6 logical drives from that. I don't understand what splitting drives into separate arrays gain us. We don't have dual controllers, so there's no benefit there. Thanks, CC

  Read the article

• PCI IDE Controller

  - by mercutio

  I have a suspicion that the onboard IDE controllers may not be working. Every disk I use to setup this machine reports as damaged (using a win xp installation to test, since it gets to partition setup fastest) So, I popped an IDE PCI Controller card in, to test with, but no drives are showing up in the bios now. I went into setup and changed the BIOS settings to disable onboard IDE1 and 2 to test, but still didn't detect the drives. How do I get that working? It's a standard PC with a 160GB disk and DVD Drive on master and slave channels on a single cable, if that helps. Let me know what else I need to state.

  Read the article

• Asus F5N laptop built-in card reader driver problem

  - by Felix Dombek

  I have an Asus F5N X50N-AP011C. I have manually installed Windows 7 x64 on it, replacing the original Windows Vista. It also automatically installed a card reader driver, but it can no longer read xD cards. The driver shows in the device manager as "Generic- xD/SDMMC/MS/Pro USB device" (under "drives" - and a drive is also shown in Windows Explorer). The same card reader once used to work with xD cards. I also tried to manually install drivers from this website: http://www.station-drivers.com/page/realtek.htm - the RTS 5158 but it didn't work (it shows as USB device in device manager, but not as a drive in Windows Explorer). Does anyone know what card reader my model has built-in? (I think it's the 5158 but I don't know how to verify that - there's also no hint in the System Information tool, only the driver name is listed under "drives") how it is connected internally? if there is a better Windows 7 x64 driver?

  Read the article

• Use server git installation in GitHub for Windows

  - by Lg102

  We are using Git as the version control for our website development. I work from a laptop, which is connected to the internal network via a WiFi connection. I've mapped the server drives as network drives in Windows. Commands such as git status take significantly longer for me than they do for my co-workers on wired connections. When connecting to the server using SSH and running commands on the git installation there, performance is even better. Is there a way to configure GitHub for Windows to use the server-installed git (with my credentials)? Note: While our production servers has a user configuration with proper permissions, the development server has only one root user.

  Read the article

• Debian SMB share having permission issues in windows 7

  - by xxpor

  Hi Everyone, I setup a Debian squeeze server with samba. I then shared my /media directory with the following configuration: [media] comment=Hard Drives read only = no locking = no path = /media guest ok = yes browsable = yes directory mask = 0777 When the drives are mapped in Windows 7, the user can write to all of the subdirectories of media (sdb1, sdc1, etc), but cannot write to any folders that they create themselves in the subdirectories of media. For example, if the user mapped /media/sdb1 to Z:, and then creates a folder Z:\test, the folder is created successfully, but no files can be written to Z:\test. If the user ssh's into the server, they have no problems writing to these directories. I have included the screenshots, in order, of what happens on Windows. This samba share is mounted with ntfs-3g, if it makes a difference. Screenshots are here

  Read the article

• Citrix has issues resolving network shares

  - by George

  We are having this weird issue with our Citrix (version 4.5) server (sitting on Windows 2003 r2), where a couple users have issues resolving single shared network drive. We use a logon script to map all shared drives. The weird part is that of 3 shared drives, users can access 2, but the 3rd one goes to the old server (even though the logon script points to the new server). And that issues is limited to a few users. I had them log off and re-loggin to no success. It happens just in Citrix. The file server, that is being accessed, is Windows 2008 R2. Like I said we use a logon script to map the network drive. I understand I might be a little confusing, I will gladly reword the post.

  Read the article

• Monitor disk I/O for specific drive in OS X

  - by raffi

  In my Macbook Pro, I have two internal drives and I've connected a third drive via USB in enclosure. I am currently doing a secure wipe of the external drive and I was interested in seeing what the disk I/O was for that particular drive, but when I use Activity Monitor I only see the total disk usage for all drives combined. Is there any way to monitor a specific drive's total I/O, preferably via a built-in or free method? I don't want to filter by process ID. I just want to filter by mounted disk.

  Read the article

• TrueCrypt Corrupted Files

  - by B. Knight

  Several months ago, I needed to reorganize my data across multiple external hard drives with my laptops primary hard drive as the go-between. My external hard drives are all encrypted with TrueCrypt. It appears to me that somehow during the transfer of my files between the encrypted external drive an the unencrypted internal drive, the files were transferred "as-is" (in their encrypted state). The files range from very small to very large. It appears that this may have happened during one consecutive transfer session. Has anyone ever experienced this problem, and if so were you able to fix it? Is there a way to recreate the encrypted partition, transfer the files, and then decrypt them to their usable state? Or can the files somehow be decrypted through other means? UPDATE: I am running Windows 7 (x64) HP now, but may have been runninG ENT. then. Toshiba Laptop 650GB HDD / 4GB Mem. Latest version of TC

  Read the article

• New 2.5" hard drive for laptop - What to compare?

  - by TFM

  I'm having trouble finding a new (bigger) hard drive for my laptop. I came across some criteria that I never thought about before, while I was checking a price comparison site. Of course, that made me more confused. First of all, I will probably go with something above 250 GB, and at least 16 MB cache. Now the confusing part: Most new drives are 7200 RPM, as opposed to good old 5400 RPM. 7200 RPM used to mean extra heat, but suddenly it's almost impossible to find a 5400 RPM in 2.5". What did I miss? Second question: Internal data transfer rate. My old drive has a rate of around 60 MB, but new drives have values like 100 MB or more (e.g. 150 MB). How important is this "internal data transfer rate"?

  Read the article

• How can I rename files and subdirectories in a copied directory based on changes in the original?

  - by GaryF

  I have a directory structure with many hundreds of files and folders underneath it for organising files (in this case photos). I create backups of that directory structure by rsyncing it to identical copies on an external drives periodically. These drives may be offsite some of the time. I want to restructure and rename the files and directories in the original and then, later, when I have an external drive onsite, be able to run some tool that will cause these structural and naming changes to happen on the backup. If I just us rsync, it'll have to recopy much of the data to the backup drive, which I'd rather avoid due to the sizes involved. How can I get the changes I make to the original directory into the backups, as they become available, without having to recopy/rsync the data?

  Read the article

• Joining windows LANs through SSH tunnel

  - by Akke

  I have at home a computer (a windows 7 ult machine) I need to use to manage stuff at the office which hosts windows and linux servers. I am able to set up a SSH tunnel (atleast for firefox proxying) and I'd like to be able to access shared windows network drives on the other end too. I heard something about needing some kind of samba service but I couldn't find anything useful by googling that. What do I need in order to make an SSH tunnel to the office (a NAS, running linux) so that I can access windows server 2008 and windows 7 network drives? Bonus: I'd like to be able to access a MSSQL database server too if it's possible.

  Read the article

• Sun Storage 2500-M2 Array and Sun Fire X4470 M2 Server

  - by nospam(at)example.com (Joerg Moellenkamp)

  There is some new hardware in the Oracle portfolio. The first one is the Sun Fire X4470 M2 Server. There was a lot of talk about the system before because of benchmark results, but now it's finally announced. Two or four Intel Xeon E7-4800. Up to 1 TB as the system provides 64 DIMM slots with 16 GB DDR DIMMs. The memory is placed on those riser cards right behind the fans of this chassis. Up to 6 internal drives. In a 3 RU package. Another announcement was the Sun Storage 2500 M2 announced yesterday: From 5 to 48 drives (the later number with three expansion trays) for up to 28.8 TB of storage. The array is SAS based internally. You can put 300GB and 600 GB in it. The 2540-M2 provides 4 (8 optional) FC ports with up to 8 GB/sec. The 2530-M2 has 4 SAS2 ports with up to 6 GBit/s. It has 2 integrated controllers providing 2 GB cache protected by a power backup for 72 hours. The controller enables the arrays to deliver 0, 1, 10, 3, 5, 6, (P+Q) RAID levels.

  Read the article

• Artemis Is The Absolute Geekiest LAN Game You’ll Ever Play [Video]

  - by Jason Fitzpatrick

  Prepare to have your sense of what really geeky computer gaming look like with this Star Trek-like mockup that involves a projector, multiple monitors, and a crew of six. If you have five friends willing to pool some resources–because let us tell you, it’s not going to be cheap to build this gaming setup from scratch–you’re on your way to building a functional starship bridge in your rec room. You’ll need six computers and monitors, a projector to create the front-of-the-bridge-room effect, and a copy of the game–the full retail game is $40 but there is a free demo so you can take the starship simulation for a test spin. The base game is focused on simple simulations like defending your space station and fighting off waves of invaders, however, a recent update of the game supports user-created mission packs. The missions packs allow fans of the game to create intricate missions with objectives to expand the game much like fan-created RPG modules add game play value to table top role-playing games. Hit up the link below to read more about the game or just sit back and enjoy the entertaining video above of sci-fi bloggers manning a starship. Artemis HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows? Java is Insecure and Awful, It’s Time to Disable It, and Here’s How What Are the Windows A: and B: Drives Used For?

  Read the article

• Auto-mount in fstab no longer working until manually running 'sudo mount -a'

  - by Brett Alton

  I have 3 SMB shared drives I need to connect to for work purposes. I had Ubuntu 10.10 Maverick and had all my drives loaded into fstab to be auto-mounted. Everything worked fine for a while but just before I upgraded to 11.04 Natty, the fstab auto-mount stopped working. Unfortunately I don't know what changed I made to my machine or what update installed that made this occur. /etc/fstab {snip} //192.168.7.3/apache_proj/ /home/brett/Desktop/apache smbfs guest,rw,iocharset=utf8,uid=1000,gid=1000 0 0 //192.168.7.3/apache_54321/ /home/brett/Desktop/54321 smbfs guest,rw,iocharset=utf8,uid=1000,gid=1000 0 0 //freenas.local/shared/ /home/brett/Desktop/shared smbfs guest,rw,iocharset=utf8,uid=1000,gid=1000 0 0 //lamp/www/ /home/brett/Desktop/lamp smbfs username={snip},password={snip},rw,iocharset=utf8,uid=1000,gid=1000 0 0 When the machine boots, I run this command to get them to mount: $ sudo umount /home/brett/Desktop/54321 /home/brett/Desktop/shared /home/brett/Desktop/apache; sudo mount -a [sudo] password for brett: umount: /home/brett/Desktop/54321: not mounted umount: /home/brett/Desktop/shared: not mounted umount: /home/brett/Desktop/apache: not mounted Warning: mapping 'guest' to 'guest,sec=none' Warning: mapping 'guest' to 'guest,sec=none' Warning: mapping 'guest' to 'guest,sec=none' mount error: could not resolve address for lamp: No address associated with hostname (I run that umount as a just-in-case). I looked through dmesg and some error logs and couldn't see why fstab was failing on my mounts. I see that my 'lamp' directive is failing, but that's because the machine is currently down.

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >