Search Results

Search found 7371 results on 295 pages for 'raid card'.

Page 44/295 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

  • Drive configuration for 5 large databases

    - by Mr. Flibble
    I've got 5 databases, each 300GB, currently on a RAID 5 array consisting of 5 drives. All the databases are used heavily, at the same time, so drive speed is an issue. Would I see better performance if I got rid of the RAID 5 configuration and just put each database on a separate drive? The redundancy provided by RAID 5 is not necessary due to mirroring elsewhere. Will the server then be able to perform reads / writes to different databases drives in parallel? More so at least than when it's in RAID? This is all on Windows 2003 / SQL 2008.

    Read the article

  • Are mobo raid controllers based on Intel ICH10R southbridge still considered software Raid?

    - by Breadtruck
    So do you still need specific software/drivers (intel matrix?) installed to manage the raid controller, setup the array. If the raid chipset is on-board the motherboard and it uses the CPU, and say I am using a Core 2 Quad Q9550, would a hardware based card still out perform the motherboard chipset? This is for a home workstation and I could spend $300 on a areca ARC-1210 PCI-Express x8 SATA II but I want to be able to justify the money for the raid card. My motherboard is a GIGABYTE GA-EP45-UD3P UPDATE: I was going to RAID5 using 4 500 GB drives, and I was going to buy a controller card but this article got me thinking hmmm....Toms-Southbridge Battle

    Read the article

  • Very slow disk performance on Dell PowerEdge 2950 w/ PERC 6/i running RAID 10

    - by vocoder
    I recently set up a server running Ubuntu 10.04 LTS on a Dell PowerEdge 2950 server - it has 6 500 gb 7200RPM SATA drives setup in a RAID 10 config. I am seeing extremely poor disk performance - the RAID array reports all disks are normal and using MegaCLI, it looks like the BBU is fine. hdparm -tT /dev/sda reports: Timing cached reads: 90 MB in 2.05 seconds = 43.96 MB/sec Timing buffered disk reads: 24 MB in 3.11 seconds = 7.72 MB/sec So as you can see, it takes forever to something as simple as an apt-get upgrade and even logging into the server. How do I go about troubleshooting what is causing this? I upgraded the firmware on the PERC 6i RAID controller to the latest, but didn't see any improvements.

    Read the article

  • AHCI and Memtest86+

    - by satanicpuppy
    I've got a motherboard with SATA AHCI enabled, and I need to disable it to run Memtest86+ (because Window's built-in RAM diagnostic tool isn't worth a barrel of warm snot), and because the Memtest developers are too lazy to fix the bootloader problem. Fine, I know how to do that. The problem is, I, in a moment of insanity driven by the fact that I work with hardware RAID cards all the time, felt the need to enable the onboard RAID. In retrospect, this was stupid: the onboard raid is a joke, but I'm stuck with it. My question is, if I disable AHCI am I going to lose the RAID information? I haven't been able to find a definitive yes or no anywhere, and I'm not in the mood to find out the hard way.

    Read the article

  • RAID 10: SPAN 2 vs SPAN 4

    - by LaDante Riley
    I am currently configuring RAID 10 (first time doing RAID ever) for a server at work. In the Configuration Utility. I am given the option of either span 2 or span 4. Having never done this before, I was curious if someone could tell me the pros and cons of for each span? Thanks The server is a Poweredge r620 with a PERC H710 mini (Security Capable) RAID controller. I have 8 600GB hard drives. I am creating this server as a network storage drive. I have SQL server historian database whose 1TB storage filled up and after 5 years of logging data.

    Read the article

  • How to make a Linux software RAID1 detect disc corruption?

    - by Paul
    This is one of the nightmare days: A virtualized server running on a Linux SW-RAID1 runs a VM that exhibits random segfaults in seemingly random codechunks. While debugging I find that a file gives different md5sums on each and every run. Digging deeper I find this: The raw disc partitions that make up the RAID1 mirror contain 2 bit-differences and ca. 9 sectors are completely empty on one disc and filled with data on the other disc. Obviously Linux gives back a sector from a undeterministically chosen disc of the mirror set. So sometimes the same sector is returned OK, sometimes the corrupted is given back. The docs say: RAID cannot and is not supposed to guard against data corruption on the media. Therefore, it doesn't make any sense either, to purposely corrupt data (using dd for example) on a disk to see how the RAID system will handle that. It is most likely (unless you corrupt the RAID superblock) that the RAID layer will never find out about the corruption, but your filesystem on the RAID device will be corrupted. Thanks. That will help me sleep. :-/ Is there a way to have Linux at least detect this corruption by using sector checksumming or something like that? Would this be detected in a RAID5 setup? Is this the moment I wish I used ZFS or btrfs (once it becomes usable without uber-admin capabilities)?

    Read the article

  • HP DL185 - very slow disk read speed

    - by fistameeny
    Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

    Read the article

  • Slow Write Speed on ESXi host

    - by Gregg Leventhal
    I have an ESXi 5.0 free host with an internal datastore of 7.2K 5 disk RAID 5 using a PERC 710 mini RAID controller in a Dell Poweredge R620 Server with 32GB Ram and a 12 Core Xeon. I seem to get slow write speeds in the guests so I checked out ESXTOP and I see 15MB/s write speed there on this host, which is comprable to the guests. What could be causing such horrible write speeds? Is RAID 5 really this slow to write??

    Read the article

  • Possible to write an implement of RAIDZ or RAIDZ2 for the MD driver in the Linux kernel?

    - by Pharaun
    I am curious on if it is possible to have an implement of RAIDZ and/or RAIDZ2 in the MD driver in the Linux kernel? From my understanding of it is that the RAIDZ version is equivalent to a RAID 5, and that a RAIDZ2 is equivalent to a RAID 6. The main difference is that the stripe size can be variable for RAIDZ as opposite to RAID 5/6 from my understanding, which helps performance. So what I am wondering is would it be possible to add this performance enhancing technique to RAID 5 & 6 in the MD driver in the kernel? Or is it tied too closely to how the ZFS works?

    Read the article

  • Intel Rapid Storage Technology - Raid5 is very slow

    - by Cederstrom
    Hi, I build a computer with a raid5, using the motherboards raid controller (ASUS P7H57D-V EVO - intel Rapid Storage Technology). The read and write are however very slow, when using the raid controller :( - I am using Windows 2008 R2, and when using the windows software raid, it was ok in speed - so there must be an issue with the controller? Im using 6 disks on 2TB each. Do anyone have any idea why its so slow, and how to fix it? I rather not pick the easy solutiuon of "just buy a raid controller" :| If you need more info about my setup, please just ask. Thanks :)

    Read the article

  • setup lowcost image storage server with 24x SSD array to get high IOPS?

    - by Nenad
    I want to build let's name it a lowcost Ra*san which would host for our social site the images (many millions) we have 5 sizes of every photo with 3 KB, 7 KB, 15 KB, 25 KB and 80 KB per Image. My idea is to build a Server with 24x consumer 240 GB SSD's in Raid 6 which will give me some 5 TB Disk space for the photo storage. To have HA I can add a 2nd one and use drdb. I'm looking to get above 150'000 IOPS (4K Random reads). As we mostly have read access only and rarely delete photos i think to go with consumer MLC SSD. I read many endurance reviews and don't see there a problem as long we don't rewrite the cells. What you think about my idea? - I'm not sure between Raid 6 or Raid 10 (more IOPS, cost SSD). - Is ext4 OK for the filesystem - Would you use 1 or 2 Raid controller, with Extender Backplane If anyone has realized something similar i would be happy to get Real World numbers. UPDATE I have buy 12 (plus some spare) OCZ Talos 480GB SAS SSD Drive's they will be placed in a 12-bay DAS and attached to a PERC H800 (1GB NV Cache, manufactured by LSI with fastpath) Controller, I plan to setup Raid 50 with ext4. If someone is wondering about some benchmarks let me know what you would like to see.

    Read the article

  • How can one associate a 3ware controller with the corresponding /dev/tw?? device?

    - by barbaz
    I have a few 3ware RAID controllers installed in a system. Is there any way to figure out the mapping between the following identifiers, each describing in a way the very same RAID controller? The tw_cli reported controller id (e.g. c0,c1,c2,...) The corresponding device nodes that allow smartctl access via the 3ware driver (e.g. /dev/twa0, /dev/twa1, /dev/twl0) The block device presented to the system representing a RAID unit (/dev/sda, /dev/sdb,...)

    Read the article

  • Which is a better use of my SSD Drive [on hold]

    - by RS Conley
    I have the choice of setting up a system with two SSD Drives in Raid 1 mode as my boot drive for Windows 7 64-bit. With the Program Files and User Folders moved to a Second regular HD Drive also configured using Raid 1. Or Setup a single SSD Drive (120 GB or 256 gb) as a cache Drive using Intel Rapid Storage Technology combined with two normal hard drives configured as Raid 1. Which setup would have the faster hard drive performance over the life of the computer?

    Read the article

  • Recover data from Dynamic Disk (MBR) bigger than 2TB

    - by Helder
    Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

    Read the article

  • Post raid5 setup reboot shows single hard drive failure on ubuntu 12.10?

    - by junkie
    I just set up raid 5 on linux using three HDDs as per a guide. It all went fine until when I rebooted I got the following text: http://i.stack.imgur.com/Zsfjk.jpg. Does this mean one of my HDDs has failed? How do I check if any of them are failing? I tried using smartctl and didn't see any issues. Or is it nothing to do with failure and something else altogether? I would like to get the raid 5 working again but I'm not sure where to go from here. I'm using ubuntu 12.10 and the three raid disks each have a gpt partition with a single full size partition of filesystem type ext4. Note I only got an error on reboot not while I was creating the raid array which went fine. Thanks.

    Read the article

  • Server with 3 Disk, what's the best HD Configuration?

    - by aleroot
    I Have an HP Server with a quad core Opteron and 3 Disk 250Gb S-ATA Disk, i'm thinking about what's the best configuration of the disk for performance and reliability. There is mainly 2 scenario : -RAID 5 with these 3 HD (on the the array 100GB Partition for OS, Other Space for Data Partition) -RAID 1 + 1 Disk for OS (one single Disk OS Installation, RAID 1 Array for a Data Partition) What's the best configuration ? In the Server Run MySQL and Small Document File server, the OS to be installed is Windows Server 2008 ...

    Read the article

  • large RAID 10 vs small RAID1

    - by user116399
    The machine will store and serve millions of small files (<15Kb each), and all those files require a total storage space of 400G Considering the exact same SATA hard drives maker and models, on the exact same environment (OS, cpu, ram, raid controller, etc...) which one of the setups bellow would be faster? A) RAID 1 with 2 drives of 2T each, making up total storage of 2T B) RAID 10 with 4 drives of 2T each, making up total storage of 4T [EDIT]: I'm aware RAID10 is faster than RAID1. The larger the disk, at least in theory, the longer will take to do seeks/writes. So, will the performance gain of RAID10 will be outweighed by the "drag" caused the larger disk area when seek/write operations happened?

    Read the article

  • How to delete removed devices from a mdadm RAID1?

    - by Kabuto
    I had to replace two hard drives in my RAID1. After adding the two new partitions the old ones are still showing up as removed while the new ones are only added as spare. I've had no luck removing the partitions marked as removed. Here's the RAID in question. Note the two devices (0 and 1) with state removed. $ mdadm --detail /dev/md1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. /dev/md1: Version : 00.90 Creation Time : Thu May 20 12:32:25 2010 Raid Level : raid1 Array Size : 1454645504 (1387.26 GiB 1489.56 GB) Used Dev Size : 1454645504 (1387.26 GiB 1489.56 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 12 21:30:39 2013 State : clean, degraded Active Devices : 1 Working Devices : 3 Failed Devices : 0 Spare Devices : 2 UUID : 10d7d9be:a8a50b8e:788182fa:2238f1e4 Events : 0.8717546 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 8 34 2 active sync /dev/sdc2 3 8 18 - spare /dev/sdb2 4 8 2 - spare /dev/sda2 How do I get rid of these devices and add the new partitions as active RAID devices? Update I seem to have gotten rid of them. My RAID is resyncing, but the two drives are still marked as spares and are number 3 and 4, which looks wrong. I'll have to wait for the resync to finish. All I did was to fix the metadata error by editing my mdadm.conf and rebooting. I tried rebooting before, but this time it worked for whatever reason. Number Major Minor RaidDevice State 3 8 2 0 spare rebuilding /dev/sda2 4 8 18 1 spare rebuilding /dev/sdb2 2 8 34 2 active sync /dev/sdc2

    Read the article

  • How to move partition with Users to a new SATA controller?

    - by Al Kepp
    Our current situation: X79 chipset. Windows 7 installed on SATA SSD running on Marvell controller. C:\Users contains just Public and computer-name folders, all the other users are created in E:\Users. That partition is on two HDD's running on an Intel RAID controller. (The motherboard has got two SATA/RAID onboard controllers.) The goal is: Without reinstallation, I want to move SSD to a standard SATA controller. Then I want to get rid of RAID1, and move one HDD to the same internal Intel SATA controller and the current E:\Users move to that new place. I want it to stay as E:\users, but I need to reinstall the HDD to let it work in SATA mode without RAID. So I face several problems. I am sure all are solvable with free software utilities, but I don't know how exactly to do it. I can see the particular problems: I have got all users at E:\Users. When I turn off that E:\ disk, I won't be able to login to Windows. I need at least one admin account to be placed back at C:\users. The current C: runs on standard 120 GB SSD, but it is connected to a Marvell SATA/RAID controller. I am affraid the Windows won't let me put it to Intel SATA controller due to hardware/licence check, and I won't be able to use standard W7 recovery disk either, because there probably isn't marvel SATA/RAID driver on it. I haven't tried anything yet, because I am affraid I can end up with computer not working at all. (I want to move it to a standard ICH10 Intel SATA controller to let us have no problems in future with it. I think it is not very safe when we use any nonstandard hardware to boot the computer.) I need to somehow backup current E:\ disk and restore it to a new E:. I hope this will be the easy part (as long as the admin account will reside on C:). The E: RAID array is very large, but it is almost empty (less than 100 GB of data.) So I can make the partition smaller so it can easily fit to a single SATA HDD.

    Read the article

  • Software Raid1 with Trim

    - by Penetal
    I have two Crucial C300 SSD disks that I would like to use as my OS disks in my new home server. I have read around a little and some places say that TRIM is simply not supported on any raid config, hw or sw. Then on some other sites I have seen that new support have come for SW raid via LVM somehow, and this is what I'm curious to know about. Can I get Raid 1 and still have TRIM enabled on SW raid by abstracting it with LVM or in any other way? I will most likely be using either Debian or CentOS.

    Read the article

  • Windows 8 Killed my SSDs

    - by SLaks
    I have a computer running 2 256GB Crucial M4's (CT256M4SSD2) in a RAID 0 (striped) array on an ASUS P9X79 Pro using Intel's (built-in) RAID system. I recently installed Windows 8 Pro as UEFI on this RAID array. (wiping a fully-function Windows 7 non-UEFI installation) Now, whenever the computer is left running for about an hour, the system no longer sees those drives. Since those drives contain Windows, this leads to various forms of BSODs. If I Intel RSTe (RAID manager) is running at the time, it will say that the disk backing that RAID array has been removed. Once this happens, if I reset the computer, it will no longer boot. Entering BIOS setup shows that the SATA 3 (6Gbps) ports that those disks are connected to are both empty. If I then power down the system completely, then turn it on again, the drives reappear, but the problem repeats after another hour or so. I have inconclusively determined that the problem occurs even if Windows is not running (booted into the installation environment from a UEFI flash drive) I don't think there has been any data corruption since this started happening, although I have had two strange issues with a GIT repo on that disk. sfc /ScanNow and Intel's disk check (in RSTe) both do not find anything. Does anyone know what might cause this?

    Read the article

  • RAID 0 disk failure, how to recover the RAID?

    - by user7985
    Situation is this. A PC with 2 hard disks, in an RAID 0 Array. The electronics on one of the disks has failed. I can not find the same board for the disk (I've tried this, removed board from the OK disk, and the second, the damaged one, works fine). I've made an image with "dd" on linux on a new hard drive (same size, not same model) and now I get "Offline member" in the RAID config screen. Will I succeed to recover the data which is stored on the drives, any help, any experience with this kind of problem. And surly, I know it was stupid to put the disks in RAID 0 and store data on them :(

    Read the article

  • The Disloyalty Card

    - by David Dorf
    Let's take a break from technology for a second; please indulge me. (That's for you Erick.) A few months back, James Hoffmann reported that Gwilym Davies, the 2009 World Barista Champion, had implemented a rather unique idea for his cafe: the disloyalty card. His card lists eight nearby cafes in London that the cardholder must visit and try a coffee. After sampling all eight and collecting the required stamps, Gwilym provides a free coffee from his shop. His idea sends customers to his competitors. What does this say about Gwilym? First, it tells me he's confident in his abilities to make a mean cup of java. Second, it tells me he's truly passionate about his his trade. But was this a sound business endeavor? Obviously the risk is that one of his loyal customers might just find a better product at a competitor and not return. But the goal isn't really to strengthen his customer base -- its to strengthen the market, which will in turn provide more customers over the long run. This idea seems great for frequently purchased products like restaurants, bars, bakeries, music, and of course, cafes. Its probably not a good idea for high priced merchandise or infrequently purchased items like shoes, electronics, and housewares. Nevertheless, its a great example of thinking in reverse. Try this: Instead of telling your staff how you want customers treated, list out the ways you don't want customers treated. Why should you limit people's imagination and freedom to engage customers? Instead, give them guidelines to avoid the bad behavior, and leave them open to be creative with the positive behavior. Instead of asking the question, "how can we get more people in our stores?" try asking the inverse: "why aren't people visiting our stores?" Innovation doesn't only come from asking "why?" Often it comes from asking "why not?"

    Read the article

  • Installing 10.10+ with Radeon HD 6970 Video Card

    - by Ben Lacy
    I built a new PC that has a Diamond Radeon HD 6970 graphics card, and no on-board graphics. When I boot from the Ubuntu disc, it runs through some initial booting stuff, and then gets to a loading screen that just has the Ubuntu logo and some progress bar/dot thingies. After this screen is finished, it goes black and says it cannot display video mode. I've seen many people that say to simply install the ati drivers. However, I don't believe this is an option, because I can't even get to the boot screen that asks me if I want to run the system off of the LiveCD, boot to hard disk, etc... Is there a way to somehow boot to a CLI before getting to the screen that would normally let me choose that? I'm at a loss as far as what to do. Also: Yes, the CD boots fine on other machines. (I've also burnt a couple discs just to be sure) Yes, the graphics card is fine. I normally dual-boot with Windows 7, and it runs on Windows just fine. Thanks for any help!

    Read the article

  • Getting Unity 3D working on legacy Nvidia card

    - by user69545
    I installed the latest nVIDIA drivers for my FX5500 card. I understand that the X server version does not officially support this driver or card but was wondering what I can do to get compiz running. I have researched for hours on this issue but cannot come up with an answer for myself. I might be doing all this for nothing but I wanted to at least try. Here is the output of my test: mike@mike-linux-box:~$ /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce FX 5500/AGP/SSE2 OpenGL version string: 2.1.2 NVIDIA 173.14.35 Not software rendered: yes Not blacklisted: no GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no So I was wondering what is the "Not Blacklisted" test? Is this the Nouveau Blacklisting? nVIDIA driver did that automatically. Does this need to be removed? Any help would be appreciated. I just want to run compiz effects. Thanks.

    Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >