Search Results

Search found 27248 results on 1090 pages for 'table adapter'.

Page 44/1090 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

  • Mini DisplayPort to DVI-D Dual Link up to 2560 * 1600

    - by Steinway Wu
    I have a ThinkPad T530 with Mini DP++ and NVS 5400M, which are said to support 2560 * 1600 resolution. The display is Dell 3007WFP, which also supports 2560 * 1600. But, I have never seen any cables or adapters that can connect them with full support to 2560 * 1600. Do you have any idea? THANK YOU! In addition, I found that mDP++ means I can use a passive adapter. No need for active adapter which is much more expensive. This is the only one that meets my needs, but it is not sold in the US. And this one seems to be OK, but I am not sure because it says "2.5 Gbps per channel", which may not be enough.

    Read the article

  • IDE <-> SATA Adapter Issue - Hard Drive Not recognized

    - by nicorellius
    I was trying to use one of these IDE to SATA adapters (Syba SD-ADA50016 IDE/SATA Converter Bi-directional IDE to SATA) and I connected a working hard drive (Seagate Barracuda 500 GB SATA 3.5 Inch 7200 RPM Version 12 Desktop Internal Hard Drive ST3500418AS). I could get the drive to be recognized by the BIOS, but I couldn't boot a Linux disc or install to the drive. I tried to install pfSense to this drive and the install failed because the setup couldn't recognize the file. Has anyone heard of these adapters giving trouble and/or not working properly? I would like to be able to use this device for newer drives on older boards.

    Read the article

  • VirtualBox reinstalling & updating has left me with Too Many Network Adapters. How Do i remove them?

    - by S3curityPlu5
    I have too many network adapters. I have had to reinstall, repair VirtualBox a few times, and I have three NICs in my laptop. I definitely don't need to have 14 bridged networking drivers though, and I cannot uninstall them. I only want to keep the new ones that came with VirtualBox 4.1.20. When I go into the registry there are tons of places with these adapters. I have searched online up to 10 pages of Google, and VirtualBox forums, and no one has mentioned this problem nor explained how to delete these annoying extra network adapters. Please offer some assistance or at least tell me how anybody else has dealt with this. I only need 1 host-only network adapter, 1 bridged networking adapter for each of my network cards. Take a look:

    Read the article

  • Routing internet through ethernet to a computer without a Wireless adapter

    - by Decency
    I'm setting up a small home network. I have a laptop which connects to internet wirelessly- that works fine. I have a desktop connected to this laptop by an ethernet cable which I'd like to access the internet with. In the past, I have used a different laptop to do this and had no problems doing so. Both computers run Windows 7. I have tried setting up a homegroup and disabling Windows firewall, as well as restarting both computers. I can share data but my internet connection can not be accessed through the desktop. (I understand USB network adapters are cheap, I have one on the way but that doesn't solve this issue.) Any help or live chat support if you'd prefer would be appreciated. Thanks!

    Read the article

  • Remote Control Adapter for PC

    - by Kairan
    Does there exist a product out there that attaches to your PC (preferably USB) that enables Infrared signals to be received (by a regular remote control) ? It seems a novel idea to be able to get a programmable remote that can be used to manipulate windows (like the Harmony remote control series) along with some programmable software (preferably Windows supported) to convert any button on a regular remote to some command on the PC. Does this exist? What is it called? This particular instance you are REQUIRED to use the crappy supplied remote, and this is not what I am looking for

    Read the article

  • Enable/Disable a network adapter with a keyboard shortcut

    - by Carlos
    I started out trying to use a shortcut to display the Local Area Connection Status window on my desktop by creating a shortcut and assigning it Ctrl+, (comma). Windows didn't like that, so it added Alt, which ended up being Ctrl+Alt++,. Since I couldn't figure out a way to eliminate Alt as part of the shortcut keys, I am now trying a different strategy and it's not working. My latest attempt is to use AutoHotkey with the following command: ^,::Run, explorer ::{BA126ADB-2166-11D1-B1D0-00805FC1270E} Which is what the shortcut target number is, but it won't open the window.

    Read the article

  • Can't transfer images from a camera connected to usb2 port on a pcmcia adapter

    - by agnul
    I have an old laptop (HP OmniBook vt6200, WinXp pro, sp2) that only has usb1 ports. Transferring pictures from a digital camera is too slow, so I thought of trying one of those pccards carrying usb2 ports (D-Link Dub C2 in my case). Connecting the camera to one of the ports on the pccard, Picasa seems to freeze trying to read the camera contents, until I either disconnect the camera or the pccard. Any idea on what's wrong?

    Read the article

  • Messenger Thinks My Ip is Invalid

    - by Umut Benzer
    Hello. I am using Windows Live Messenger 2009 on Windows 7. I am using a 3G modem (ZTE Propietary USB Modem) I connect to the Internet using a software my ISP provided me. In last three days, my Messenger started to disconnect. Here is what I observed and tried to do: 1- I can browse web, can do FTP transfer etc. and obiviously have a valid IP. 2- I can sign in to Messenger (appear offline) but when I change my status to anything other then appear offline, Messenger says my connection to service has been lost. (However, it exists.) 3- When I run, MSN Connection Troubleshooter, it says my IP is invalid. When I click repair, it says repaired and just after that, I run the troubleshooter again, and it says my IP is invalid again. (However, it is valid and I am browsing the net.) 4- If I connect the Internet through eterhet or wireless there is no problem at all. 5- I re-installed Messenger (deleting all settings manually through registry and folders), re-installed all drivers and software related to USB 3G Modem. It doesn't work. And then, I took a full backup then formatted entire computer, installed a fresh windows 7, after 5 minutes, the same problem occured. What do you recommend? What can I do? Addition As seen on screenshot, it says Server IPv4 adress is 0.0.0.0 It seems like a problem, I don't know if it is. If it is, how can I solve it? Here is what I get, when I netstat. PPP adapter TTNET internet: Connection-specific DNS Suffix . : IPv4 Address. . . . . . . . . . . : 217.174.39.122 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ege.edu.tr Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 16: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 13: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter 6TO4 Adapter: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 12: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 14: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 17: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 25: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 20: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 18: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 19: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 22: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 21: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 15: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 23: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e74:2448:3909:2a2c:eb7b Link-local IPv6 Address . . . . . : fe80::2448:3909:2a2c:eb7b%30 Default Gateway . . . . . . . . . : Tunnel adapter Local Area Connection* 24: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{CFFCFEDB-6B53-42E0-B091-548B9ADE9C9D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 26: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 27: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 29: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 31: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 28: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter Local Area Connection* 32: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2002:d9ae:277a::d9ae:277a Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 30: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{157CF713-B3AC-4701-87A9-14C23CA60AAB}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.ege.edu.tr: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Tunnel adapter isatap.{0D3CD01B-0993-4B37-89B8-12557ECF484D}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

    Read the article

  • Enabling the log app on the WDTV

    - by Ariel Popovsky
    Just flashed the last WDXLTV firmware on my WDTV and it's working fine. I tried to config a Wifi USB adapter but couldn't get it to work. Dropped the log-saver.app.bin on the root of the stick but didn't find any log files after booting. What I'm doing is turning on the WDTV with the stick inserted (the stick is formatted with FAT32). Tried with the wireless-mod.app.bin required files and without any other file than the log saver. I can't get a log file anyway. All I want right now is to get the log file so I can debug the WI FI adapter.

    Read the article

  • Mini-DisplayPort to HDMI Adapter Sound Stopped Working

    - by jimdrang
    I have cancelled cable and want to watch the NCAA tournament games on my TV tonight through my 2011 Macbook Pro where I can stream the game in a browser. I have a cheap Mini-DisplayPort to HDMI converter that I have connected to my TV in the past and had no issues with audio or video, the problem is the audio has stopped working since the last time I used it a few months ago and now just keeps playing through the laptop speakers, but the video works fine. Everything with my setup is the same and when I try to force the audio output to the TV in the Audio system settings, my TV is not listed as an output option at all. I have tried various combinations of power cycling, replugging-in both devices and making sure the TV options are set properly to receive audio through HDMI but no luck. Anyone know what the issue could be?

    Read the article

  • How can I connect a SAS drive to USB? [closed]

    - by dave
    I have a Dell T710 with Seagate Cheetah 15k.7 SAS disks. If the T710 motherboard dies, I'll need to resort to one of my nightly off-site backups and salvage the journal/logfile from the SAS disk to bring the backup bang up-to-date. I need a way of reading the healthy-but-inaccessible SAS disc that does not depend on the only SAS-capable machine I have to hand. So I bought: SAS to SATA Adapter and: USB 2.0 to SATA Adapter with Power ...so that I could read the SAS drive via USB. I can plug it all together just fine. The chain looks like: USB - SATA - SAS. But the drive does not spin up and the computer doesn't even acknowledge anything being attached by USB. Is there a cheap external enclosure I can buy for SAS drives? I can't believe these USB to SATA adapters are everywhere but the USB to SAS adapters are almost non-existent...

    Read the article

  • Windows Server 2008 R2 network adapter stops working, requires hard reboot

    - by Geoff Dalgas
    TL;DR version: Turns out this was a Windows Server 2008 R2 kernel networking bug. After siccing Microsoft support on it, we (eventually) got an unpublished kernel hotfix from Microsoft to address it. If you, too, are experiencing mysterious low-level network driver failures requiring a reboot/bluescreen cycle, you might want that hotfix (or maybe Service Pack 1 whenever it is released, too.) We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps. Switch Virtualization providers On the off chance this was related to Hyper-V in some way (we do host Linux VMs on it), we switched to VMWare Server. No change. Switch host model We've reached the end of our troubleshooting rope and are now formally involving Microsoft support. They recommended changing the host model: http://en.wikipedia.org/wiki/Host_model http://technet.microsoft.com/en-us/magazine/2007.09.cableguy.aspx We did that, and.. we'll see.

    Read the article

  • Problems when trying to connect to a router wirelessly

    - by Ruud Lenders
    The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

    Read the article

  • Same SCSI drive appears multiple times on the controller list

    - by ohad
    Hi, I have an Adaptec AHA-2940UW SCSI adapter, to which I connected a single Atlas 10K III drive (and nothing more). When my computer loads up, the pre-OS Adaptec screen shows (I believe this is called the POST screen), where I can see the Atlas drive listed many times (i.e. with ID0, ID1, ... ID5, ID7, ID8,...,ID15 [ID6 is the adapter itself]) Using the same HD on an Adaptec AHA-2940UB the disk only shows once Since my OS hasn't been installed yet, I'm not sure if this is a problem (I would guess it is), and if so - how to solve it. Termination and multiple LUNs come mind, but the cable provides termination and I don't see why a hard drive would request multiple LUNs, especially considering it is not jumpered at all, and multuple LUN support is disabled in the Adaptec controller BIOS (via the SCSISelect utility) Thank you

    Read the article

  • 2.5" SSD in a 3.5" desktop drive bay normal?

    - by Cory Petosky
    I'm a little out of touch with modern desktop builds, but I recently built a new machine anyway. I want to pick up a SSD for my I/O intensive apps (EverQuest 2 and Flash CS4 mostly), but I'm having trouble finding any in the 3.5" form factor. Is this expected, or do I fail at product search? And, if it is expected, do 2.5" SSDs come with an adapter to fit them in my desktop machine, or will I need to purchase one separately? And, finally, if I do need to purchase an adapter, are they pretty standard or are some better than others. General advice is most welcomed, though specific product recommendations in addition would be helpful!

    Read the article

  • Cisco VPN Client on Vista - Virtual Adapter

    - by ScaleOvenStove
    I have used the Cisco VPN client for years, and on XP it is pretty much rock solid, on Vista, not so much. You might be able to connect, but unless you set up a constant ping to something, it usually will disconnect, with this error: Reason 442: Failed to enable Virtual Adapater Now, most sysadmins will say, update you client - yes, I know, it hasnt mitigated the issue, ever. I have been using it on Vista since it came out, and updated my client every time a new update comes out. I have used it where the VPN server was a Cisco PIX and a Windows Box allowing the Cisco Client to connect. Anyone have any fixes that you can do on your client to fix this issue?

    Read the article

  • Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

    - by CITguy
    Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

    Read the article

  • Installing sharepoint web service disabled when trying to install BizTalk adapter

    - by noesgard
    I have a MOSS Box, with Microsoft Office SharePoint Server 2007 SP2 (Danish server), .net 3.5 SP1 on a Server 2008 64 bit (where IIS is running 64 bit too). When I fire up the BizTalk installer and wants to select the SharePoint Web Service, this option is disabled/grayed out. Any ideas as how I can enable the option again? (It states that there are one or more prerequisites missing but I can't figure out which). I found some reference stating that I basically had to "toast" the MOSS box and install WSS 3, but that is NOT an option... Any suggestions? :o)

    Read the article

  • windows: force user to use specific network adapter

    - by Chad
    I'm looking for a configuration/hack to force a particular application or all traffic from a particular user to use a specific NIC. I have an legacy client/server app that has a "security feature" that limits connections based on IP address. I'm trying to find a way to migrate this app to a terminal server environment. The simple solution is for the development team to update the code in the application, however in this case that's not an option. I was thinking I might be able to install VMware NIC's installed for each user on the terminal server and do some type of scripting to force that user account to use a specific NIC. Anybody have any ideas on this? EDIT 1: I think I have a hack to work around my specific problem, however I'd love to hear of a more elegant solution. I got lucky in that the software reads the server IP address out of a config file. So I'm going to have to make a config file for each user and make a customer programs files for each user. Then add a VMware NIC for each user and make each server IP address reside on a different subnet. That will force the traffic for a particular user to a particular IP address, however its really messy and all the VM NIC's will slow down the terminal server. I'll setup a proof of concept Monday and let the group know how it affects performance.

    Read the article

  • How may I retrieve data from an Excel table based on a variable number of criteria?

    - by Eshwar
    I have the following salary data for example: Country State 2012 2013 -> 2027 ======= ===== ==== ==== China Other 1000 1100 China Shanghai 1310 1400 China Tianjin 1450 1500 India Orissa 1500 1600 So now in another Excel sheet I would want an answer to one of the following questions: What is the salary in Shanghai for 2013? (Answer would be 1400) What is the salary in Hubei province for 2012? (Since it is not listed, use "Other" - 1000) What is the average salary in China for 2013? (Answer would be 1450) What is the highest salary in China for 2012? (Answer is Tianjin) So as in the above order of priority, I would like those numbers in another Excel sheet using some form of query. I considered PivotTables but I was wondering if there is another much better more efficient way of doing this? I imagine SQL is suited for this but I am not clued up on that. Some Excel functionality is much rather preferred. Also suggestions on an appropriate format of data for such queries would be appreciated.

    Read the article

  • Odd Language In a BIOS Message

    - by Josh
    So I started up my laptop today and was greeted with the following message (not a direct quote): The type of the AC adapter cannot be determined. This may interfere with your computer's performance. Try unplugging the AC adapter and then plugging it back in, thanks. The problem was that I hadn't fully secured the plug into the back of the computer. However, I was a little taken aback when a message from BIOS said, "thanks." Is this normal? Any chance the message was illegitimate (virus)?

    Read the article

  • USB 3 to Gigabit Ethernet adapters: where are they?

    - by intuited
    I'm looking for an adapter that will let me use a USB 3 port as a Gigabit Ethernet port. This is proving surprisingly hard to find! Is there some reason why this product is either unavailable or very obscure? Is there an online shop (US/Canada) where I can buy such an item? Newegg, TigerDirect, NCIX, etc. do not seem to carry such an item. I find this surprising since it will provide at least double the bandwidth (possibly quadruple) compared to a USB 2 Ethernet adapter.

    Read the article

  • Installing linux on computer with Marvell adapter

    - by Seth
    I recently reinstalled my computer and decided that I want to have a native installation of linux side by side with windows (got tired of VMWare). The thing is upon installation (debian) everything goes fine until the disc detection section - linux can't find my western digital 1TB drive (IDE mode). I don't have the installation disc with me now, but I think that when i changed the mode to AHCI everything worked, though Windows couldn't boot so this is not an option. I have a Marvell 91xx controller. Any ideas?

    Read the article

  • Why my Network Connection Properties don't show UAC prompt & settings change everytime I connect?

    - by Manish Shrivastaw
    I can't set my network connection interface properties, UAC prompt doesn't appear anymore for only this adapter interface. I disable Netbios but each time I connect it changes back to default. Earlier I could set & forget easily as UAC prompt showed for this dialup 3G connection. It's very frustrating to change settings every time. Is there any way to make adapter interface 'blacklisted' (remove from UAC whitelist) again. I can manually make a connection (that shows Uac prompt) but my dialler app doesn't work with that. Is there any registry entry for setting privilege for Napagent etc. Or what could be the reason, please guide. All I want is to set my connection properties (Tcp advanced settings) which won't change.

    Read the article

  • seeking help with Chrome & Safari not rendering my table stretched to fit its contents...help?

    - by oompa_l
    I have an element on this web page I'm developing where I need my text to conform to the width of an image above it - whose width will always be different - think of captions. I have found numerous references to using a 1px table to force this width sizing behaviour. I am having problems, though with Safari and Chrome "seeing" this instruction - the text ends up as a marginally sized text box sitting behind the image. The problem, as I see it, has to do with the text and images sitting in div's nested within the table. I need the images to sit in a div because of some jquery script I'm using called cycle, which turns a group of images into a slideshow. The problem may have something to do with the script as well. In any case, I have tried a seeming infinite number of combination of floating left and clearing left on all all the divs, changing their positions and widths...nothing works. Anyone have any clues about how to broach this one? EDIT 1: ok, should I be editing my post or responding with answers? here's the url to see the problem I am having - http://friedmanstudios.ca/webdev/test8.html and the code: <div id="content" class="boxes"> <table> <tr> <td > <div id="imageFrame"> <a href="#" class="img" title="_MG_9786_fmt.jpeg"> <img src="images/_MG_9786_fmt.jpeg"/> </a> <a href="#" class="img" title="IMG_5169_fmt.jpeg"> <img src="indesign export/GFA-TEARSHEETS-100526-01-web-images/IMG_5169_fmt.jpeg"/> </a> <a href="#" class="img" title="IMG_5175_fmt.jpeg"> <img src="indesign export/GFA-TEARSHEETS-100526-01-web-images/IMG_5175_fmt.jpeg"/> </a> <a href="#" class="img" title="aerial_fmt.jpeg" width=""> <img src="indesign export/GFA-TEARSHEETS-100526-01-web-images/aerial_fmt.jpeg"/> </a> </div> <div id="cycleCtrl"> <div id="prev" class="pager"><a href="#">< Prev</a> </div> <div id="next" class="pager"><a href="#">Next ></a></div> <div id="pagerNav" class="pager"></div> </div> <div id="descController"> <img src="images/arrow.gif" name="arrow" width="5" height="10" id="arrow" /> <span id="projectName">Toronto Centre for the Arts </span> <br /> <div id="desc"> In the past eight years... </div> </div></td> <td width="90%"><!--push col 1 back--></td> </tr> </table> and the styles: #content { position: absolute; top: 250px; left: 275px; float: left; clear: both; } content table { float: left; width: 1px; } imageFrame { position: relative; float: left; clear: left; width: inherit; } desc { position: relative; clear: left; float: left; } descController { position:relative; padding-top:5px; padding-bottom:10px; clear: left; float: left; } descController div { height:0; overflow:hidden; -webkit-transition:all .5s ease; -moz-transition:all .5s ease; -o-transition:all .5s ease; transition:all .5s ease; padding-top:10px; margin-top: 10px; word-spacing: 0em; line-height: 16px; font-size: 12px; position: relative; float: left; clear: left; }

    Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >