Search Results

Search found 12899 results on 516 pages for 'jrockit virtual edition'.

Page 441/516 | < Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >

• Asus K50I sound issues

  - by MrStatic

  I have an Asus K50IJ (Bestbuy) laptop and have issues with my sound. Speakers themselves work fine but when I plug into the headphone jack it auto mutes the front channel and no sounds comes out of either the speakers or the headphones. If I then unmute the channel I get sound from both the speakers and the headphones. alsamixer shows the Headphone channel as all grayed out. /etc/modprobe.d/alsa-base.conf I have tried snd-hda-intel model="asus-laptop" and snd-hda-intel model="asus" In Sound Preferences I have gone to output and changed the Connector to 'Analog Headphones' that results in no sound from either speakers or headphones. As one forum suggested I tried to comment out blacklist snd_pcsp in the blacklist.conf which resulted in no change. lspci -v shows: 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) Subsystem: Santa Cruz Operation Device 1043 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at fe9f4000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel

  Read the article

• Postfix message ID originating process?

  - by Anders Braüner Nielsen

  Last night my postfix mail server(Debian Squeeze with dovecot, roundcube, opendkim and spamassassin enabled) started sending out spam from a single domain of mine like these: $cat mail.log|grep D6930B76EA9 Jul 31 23:50:09 myserver postfix/pickup[28675]: D6930B76EA9: uid=65534 from=<[email protected]> Jul 31 23:50:09 myserver postfix/cleanup[27889]: D6930B76EA9: message-id=<[email protected]> Jul 31 23:50:09 myserver postfix/qmgr[7018]: D6930B76EA9: from=<[email protected]>, size=957, nrcpt=1 (queue active) Jul 31 23:50:09 myserver postfix/error[7819]: D6930B76EA9: to=<[email protected]>, relay=none, delay=0.03, delays=0.02/0/0/0, dsn=4.4.2, status=deferred (delivery temporarily suspended: lost connection with mta5.am0.yahoodns.net[66.196.118.33] while sending RCPT TO) The domain in question did not have any accounts enabled but only a catchall alias set through postfixadmin - most emails were send from a specific address I use frequently but some were also sent from bogus addresses. None of the other virtual domains handled by postfix were affected. How can I find out what process was feeding postfix/sendmail or more info on where they originated? As far as I can tell php mail() wasn't used and I've run several open relay tests. I did a little tinkering(removed winbind from the server and ipv6 addresses from main.cf) after the attack and it seems to have subsided but I still have no idea how my server was suddenly sending out spam. Maybe I fixed it - maybe I didn't. Can anyone help figuring out how I was compromised? Anywhere else I should look? I've run Linux Malware Detect on recently changed files but nothing found.

  Read the article

• How can I prevent Apache from asking for credentials on non SSL site

  - by Scott

  I have a web server with several virtual hosts. Some of those hosts have an associated ssl site. I have a DirectoryMatch directive in my main config file which requires basic authentication to any directory with secured as part of the directory path. On sites that have an SSL site, I have a rewrite rule (located in the non ssl config for that site), that redirects to the SSL site, same uri. The problem is the http (80) site asks for credentials first, and then the https (443) site asks for credentials again. I would like to prevent the http site from asking and thus avoid the potential for someone entering credentials and having them sent in clear text. I know I could move the DirectoryMatch down to the specific site, and just put the auth statement in the SSL config, but that would introduce the possibility of forgetting to protect critical directories when creating new sites. Here are the pertinent declarations: httpd.conf (all sites): <DirectoryMatch "_secured_"> AuthType Basic AuthName "+ + + Restrcted Area on Server + + +" AuthUserFile /home/websvr/.auth/std.auth Require valid-user </DirectoryMatch> site.conf (specific to individual site) <DirectoryMatch "_secured_"> RewriteEngine On RewriteRule .*(_secured_.*) https://site.com/$1 </DirectoryMatch> Is there a way to leave DirectoryMatch in the main config file and prevent the request for authorization from the http site? Running Apache 2 on Ubuntu 10.04 server from the default package. I have AllowOverride set to none - I prefer to handle things in the config files instead of .htaccess.

  Read the article

• Checking partition alignment with PowerCLI

  - by Julian

  I'm trying to verify that the file system partitions within each of the servers I'm working on are aligned correctly. I've got the following script that when I've tried running will either claim that all virtual servers are aligned or not aligned based on which if statement I use (one is commented out): $myArr = @() $vms = get-vm | where {$_.PowerState -eq "PoweredOn" -and $_.Guest.OSFullName -match "Microsoft Windows*" } | sort name foreach($vm in $vms){ $wmi = get-wmiobject -class "win32_DiskPartition" -namespace "root\CIMV2" -ComputerName $vm foreach ($partition in $wmi){ $Details = "" | Select-Object VMName, Partition, Status #if (($partition.startingoffset % 65536) -isnot [decimal]){ if ($partition.startingoffSet -eq "65536"){ $Details.VMName = $partition.SystemName $Details.Partition = $partition.Name $Details.Status = "Partition aligned" } else{ $Details.VMName = $partition.SystemName $Details.Partition = $partition.Name $Details.Status = "Partition not aligned" } $myArr += $Details } } $myArr | Export-CSV -NoTypeInformation "C:\users\myself\Documents\Scripts\PartitionAlignment.csv" Would anyone know what is wrong with my code? I'm still learning about partitions so I'm not sure how I need to check the starting off-set number to verify alignment. EDIT: $myArr = @() $vms = get-vm | where {$_.PowerState -eq "PoweredOn" -and $_.Guest.OSFullName -match "Microsoft Windows*" } | sort name $wmi = get-wmiobject -class "win32_DiskPartition" -namespace "root\CIMV2" -ComputerName $vm #foreach ($_ In Get-WMIObject Win32_DiskPartition | Select Name, BlockSize, NumberOfBlocks, StartingOffSet, @{n='Alignment'; e={$_.StartingOffSet/$_.BlockSize}}) {$_} foreach ($wmi| Select Name, BlockSize, NumberOfBlocks, StartingOffSet, @{n='Alignment'; e={$_.StartingOffSet/$_.BlockSize}}) {$_}

  Read the article

• PHP displays blank white page even with all error reporting enabled

  - by Andy Shinn

  I am trying to debug a broken page in a Drupal application and am having a hard time getting PHP to spit anything useful out. I have the following set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On error_log = /var/log/php/php_error.log I have a file showing me phpinfo() which confirms these variables are set correctly for the environment. I have increased memory_limit to 256M (which should be more than enough). Yet, the only indication I get is a status 500 code in the apache access log and a blank white page from PHP. The Apache virtual host has LogLevel set to debug and the error log only outputs: [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 0 to 2 : URL /index.php, referer: http://ec2-174-129-192-237.compute-1.amazonaws.com/admin/reports/updates [Sat Jun 16 20:03:03 2012] [error] [client 173.8.175.217] File does not exist: /var/www/favicon.ico [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 42 to 44 : URL /favicon.ico The PHP error log outputs nothing at all. kernel and syslog show nothing related to Apache or PHP. I have also tried installing suphp and checking its log just confirms the user is executing correctly: [Sat Jun 16 20:02:59 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 [Sat Jun 16 20:05:03 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 This is on Ubuntu 12.04 x86_64 with the following PHP modules: ii php5 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.3.10-1ubuntu3.1 command-line interpreter for the php5 scripting language ii php5-common 5.3.10-1ubuntu3.1 Common files for packages built from the php5 source ii php5-curl 5.3.10-1ubuntu3.1 CURL module for php5 ii php5-gd 5.3.10-1ubuntu3.1 GD module for php5 ii php5-mysql 5.3.10-1ubuntu3.1 MySQL module for php5 So, what am I missing here? Why no error reporting?

  Read the article

• Debian Stable: Can't update kernel, libc won't update.

  - by pascal

  I use Debian Stable (squeeze) on a virtual host where I can't touch the kernel, it's stuck (and will be for some time as support told me) at Linux 2.6.18-028stab070.3 #1 SMP Wed Jul 21 18:33:27 MSD 2010 x86_64 So when I try to update, several packages fail with FATAL: kernel too old for example Preparing to replace libgcc1 1:4.6.0-11 (using .../libgcc1_1%3a4.6.1-1_amd64.deb) ... Unpacking replacement libgcc1 ... Setting up libgcc1 (1:4.6.1-1) ... FATAL: kernel too old Segmentation fault dpkg: error processing libgcc1 (--configure): subprocess installed post-installation script returned error exit status 139 and some version chaos ensued: The following packages have unmet dependencies: libc-dev-bin : Depends: libc6 (> 2.13) but 2.11.2-13 is installed libc6 : Depends: libc-bin (= 2.11.2-13) but 2.13-5 is installed libc6-dev : Depends: libc6 (= 2.13-5) but 2.11.2-13 is installed libquadmath0 : Depends: gcc-4.6-base (= 4.6.0-2) but 4.6.0-11 is installed libstdc++6 : Depends: gcc-4.6-base (= 4.6.0-2) but 4.6.0-11 is installed locales : Depends: glibc-2.13-1 What should I do? I want to keep the system up-to-date, so I want to pin as few packets as possible, but I also don't want to have to compile anything manually. Trying to pin the status quo and figured out where the error came from: ldconfig segfaults. -v doesn't print anything more so I can't tell what's the actual problem. # ldconfig FATAL: kernel too old

  Read the article

• Best Practices for adding Exchange Archive to current 3 server setup

  - by ADquestion

  I'm looking to add an Archive Database (which I know is just a Mailbox Database) to our current Exchange 2010 environment. I have done this in the past at a previous job, but we had a simpler setup than at this current job. I've been trying to find some best practices to make sure it's setup in an ideal way, but so far not finding the details I would prefer. Hoping someone on here can give me a few pointers. Currently we have a 3 server setup, Server1, Server2 and Server3. Three databases of course, DB1, DB2 and DB3. We have a DAG setup between them. Server1 has DB1 and DB3 on it, DB1 is not active, DB3 is active. Server2 has DB1 and DB2 on it, both are active. Server3 has DB2 and DB3 on it, both are not active. All three servers are virtual (VMware). Each one is setup identical to the other as follows: C:\ 60GB - OS E:\ 600GB - DB (currently only 90GB used, pointing to Datastore just for Server2) F:\ 200GB - Log (2GB used, pointing to same Datastore as above) G:\ 200GB - Restore (0 used, pointing to same Datastore as above) The drives are all set to Thin Provisioning, and it looks as though I have 600GB of available space. They have not been on Exchange that long and only have about 70GB worth of PSTs to import back in that will be going to the Archive Database, plus anything older than 2 years from their current inbox that will be moved into there. I was considering placing the Archive DB on the E:\ drive of Server3 (only) like the current DB, but wasn't sure if that was acceptable. I don't plan on setting the Archive DB up with the DAG, just plan on having it as a single repository for older emails and manually back it up every now and then. If anyone has any suggestions on this I would appreciate it the input. I've done it on a slightly smaller scale before and it worked well, but like to think it through before pulling the trigger, especially at a new job. :) Thanks again!

  Read the article

• Virtualization in Ubuntu 9.10

  - by Jeff Dege

  I have an existing Centos 5 installation. I would like to upgrade to Ubuntu. Thing is, I don't want to be down for as long as it will take to get my entire environment moved over - software installed, connectivity configured, etc. I'd like to take it one step at a time. But I don't really want to keep rebooting back and forth from the new OS to the old OS. That's what I did last time I upgraded to a new OS, and it got old real fast. So, since my new MB is virtualization-ready (AMD Phenom II 945 quad-core), I figured I could create a virtual machine, under the new OS installation, that ran the old OS installation. The problem is that the documentation I've been able to find has been pretty sparse. I've found a lot of possibilities, and little info on which would be capable of doing what I want. I have a new Ubuntu 9.10 installation, and a second disk containing the Centos 5 installation. And I don't know where to go next. Any help would be appreciated.

  Read the article

• apache2 server running ruby on rails application has go daddy cert that works in chrome/firefox and ie 9 but not ie 8

  - by ryan

  I have a rails application up on a linode ubuntu 11 server, running apache2. I have a cert purchased from godaddy, (where we also bought our domain) and the cert is installed on my server. Part of my virtual host file: ServerName my_site.com ServerAlias www.my_site.com SSLEngine On SSLCertificateFile /path/my_site.com.crt SSLCertificateKeyFile /path/my_site.com.key SSLCertificateChainFile /path/gd_bundle.crt The cert works fine in Chrome, FireFox and IE 9+ but in IE 8- I get this error: There is a problem with this website's security certificate. The security certificate presented by this website was issued for a different website's address. I'm hosting multiple rails apps on this same server (4 right now plus some old php sites that don't need ssl). I have tried googling every possible combination of the error/situation that I could think of but at this point I'm shooting in the dark. The closest I could come up with is that some versions if IE don't support SNI. But that doesn't apply here because I am getting the warning on windows 7 machines running IE 8, and the SNI only seemed to apply to IE 8 if the operating system was windows XP. So why is this cert being accepted by all browsers but giving me a warning in IE 8? Edit: So doing a little more digging and I figured out some more. It turns out this is effecting IE 9 as well. However the problem seems to be that IE is not traversing the ssl chain to get to the right cert. FireFox and Chrome when I go to view certificate show the correct one, but IE is showing one of our other sites certificates. REAL QUESTION HERE: That being the case why is IE not getting the right certificate when others are and how do I fix it?

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• Any program to help me check whether an ethernet channel can support full-length VLAN packet?

  - by Jimm Chen

  Sometimes, I have to face such a situation that I need to quickly and explicitly know whether a full length VLAN packet can traverse between two RJ45 ports. Yes, I mean 802.1Q ethernet frame with Etype=81 00 (diagram below). What I can do now is: Get two Windows PCs, for each PC, intall Intel Gigabit NIC and Intel specific driver to create a virtual NIC, with VLAN ID=3 assigned. Then connect the two PCs to each of the two RJ45 port. Finally execute ping to generate a full-length ethernet packet. ping -f -l 1472 <dest-IP> This way, I can be sure that the sent packet has the maximum "IP data payload" of 1500 bytes(8 bytes of ICMP header and 1472 bytes of ICMP data). If the ping gets reply, I know that the ethernet channel support full-length VLAN packet. From my experiment, some home switch or broad band routers(e.g. Linksys WRT54G) does not support full-length VLAN packet switching, so only ping -f -l 1468 succeeds. You see, I have to use an expensive Intel NIC to carry on that test, quite inconvenient. You know, for most laptop today, they do not equip an Intel NIC, and, even it is an Intel NIC, Intel VLAN driver, Intel has limitations on the models on which VLAN driver can be installed. So, my question is: Is there a small program that can let me send a full-length VLAN packet without installing a dedicated VLAN driver? Or better, the program has a stock feature that does the very job for my situation. Windows programs preferred, Linux solution welcome. Simpler the program, the better. Thank you.

  Read the article

• Node js server not responding outside localhost centos

  - by David Martinez

  I'm running a basic express server from CentOS but for some reason it is not responding outside of localhost, I have tried everything I have found on google but nothing works so far. This is my express server: app.listen(3000,"0.0.0.0"); If I do curl http://localhost:3000/ in the server it works fine. If I curl to the ip of the server it doesn't work. I already changed my iptables num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 2 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 3 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:3000 There is currently a apache server running on port 80 with no problems. I also tried setting a VirtualHost on apache but it didn't work either: <VirtualHost *:80> ServerName SubDOmain.MyDomain.com ProxyRequests off <Proxy *> Order allow,deny Allow from all </Proxy> ProxyPass / http://localhost:3000/ ProxyPassReverse / http://localhost:3000/ ProxyPreserveHost on </VirtualHost> There is another virtual host working fine that redirects to another DocumentRoot. I'm running Node on root for testing purpose, but the node application owner is another user. All folders have 705 and files 664 Edit: I stopped apache and run my node app on port 80 and it working fine, I could access node app from my ip and domain.

  Read the article

• [tcpdump] Proxy delegate refusing connexion ?

  - by simtris

  Hi guys, I'm a little disapointed ! My aim was to build a VERY simple smtp proxy under debian to handle mail from a port (51234) and forward it to the standard 25 port. I compile and install a "delegate" witch can handle easily that. It's working very well like that : delegated SERVER="smtp://anotherSmtpServer:25" -P51234 The strange thing is, it's working on my virtual test machine and on the dedicated server in local but I can't manage to use it trought internet. I test it like that. telnet [mySrv] 51234 Of course, no firewal, no deny host, no ined/xined, the service delegated is listening on the right port ... 2 clues : The port is answering trought internet with nmap as "51234/tcp open tcpwrapped" have a look at the tcpdump following : 22:50:54.864398 IP [myIp].1699 [mySrv].51234: S 2486749330:2486749330(0) win 65535 22:50:54.864449 IP [mySrv].51234 [myIp].1699: S 2486963525:2486963525(0) ack 2486749331 win 5840 22:50:54.948169 IP [myIp].1699 [mySrv].51234: . ack 1 win 64240 22:50:54.965134 IP [mySrv].43554 [myIp].auth: S 2485396968:2485396968(0) win 5840 22:50:55.243128 IP [myIp] [mySrv]: ICMP [myIp] tcp port auth unreachable, length 68 22:50:55.249646 IP [mySrv].51234 [myIp].1699: F 1:1(0) ack 1 win 46 22:50:55.309853 IP [myIp].1699 [mySrv].51234: . ack 2 win 64240 22:50:55.310126 IP [myIp].1699 [mySrv].51234: F 1:1(0) ack 2 win 64240 22:50:55.310137 IP [mySrv].51234 [myIp].1699: . ack 2 win 46 The part "auth" seems suspect to me but didn't ring a bell. I could certaily do with some help. Thx a lot !

  Read the article

• Requests per second slower when using nginx for load balancing

  - by Ed Eliot

  I've set up nginx as a load balancer that reverse proxies requests to 2 Apache servers. I've benchmarked the setup with ab and am getting approx 35 requests per second with requests distributed between the 2 backend servers (not using ip_hash). What is confusing me is that if I query either of the backend servers directly via ab I get around 50 requests per second. I've experimented with a number of different values in ab the most common being 1000 requests with 100 concurrent connections. Any idea why traffic distributed across 2 servers would result in fewer requests per second than hitting either directly? Additional info: I've experimented with worker_processes values of between 1 and 8, worker_connections between 1024 and 8092 and have also tried keepalive 0 and 65. My main conf currently looks like this: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; worker_rlimit_nofile 8192; events { worker_connections 2048; use epoll; } http { include /etc/nginx/mime.types; sendfile on; keepalive_timeout 0; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } I've got one virtual host (in sites available) that redirects everything under / to 2 backends across a local network.

  Read the article

• Why my Ldirectord check multiple times on read server every interval?

  - by garconcn

  I have a Ldirectord server and two real servers. My ldirectord used to check the request page on real server once in every interval, but now I found that it check four times. I have monitored the log on both real servers, they have the same problem. Here is my ldirectord configuration: checktimeout=10 checkinterval=5 autoreload=yes logfile="/var/log/ldirectord.log" quiescent=no virtual=192.168.1.100:80 fallback=127.0.0.1:80 real=192.168.1.10:80 gate real=192.168.1.20:80 gate service=http request="lb.html" receive="still alive" scheduler=sh persistent=60 protocol=tcp checktype=negotiate Ldirectord will connect to each real server once every 5 seconds (checkinterval) and request 192.168.0.10:80/test.html (real/request). The access log in real server: 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:44 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:49 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805" 192.168.1.100 - - [13/Jun/2012:10:36:54 -0700] "GET /lb.html HTTP/1.1" 200 12 "-" "libwww-perl/5.805"

  Read the article

• How to use basic auth for single file in otherwise forbidden Apache directory?

  - by mit

  I want to allow access to a single file in a directory that is otherwise forbidden. This did not work: <VirtualHost 10.10.10.10:80> ServerName example.com DocumentRoot /var/www/html <Directory /var/www/html> Options FollowSymLinks AllowOverride None order allow,deny allow from all </Directory> # disallow the admin directory: <Directory /var/www/html/admin> order allow,deny deny from all </Directory> # but allow this single file:: <Files /var/www/html/admin/allowed.php> AuthType basic AuthName "private area" AuthUserFile /home/webroot/.htusers Require user admin1 </Files> ... </VirtualHost> When I visit http://example.com/admin/allowed.php I get the Forbidden message of the http://example.com/admin/ directory. How can I make an exception for allowed.php? If not possible, maybe I could enumerate all forbidden files in another Files directive? Let's say admin/ contains also user.php and admin.php which should be forbidden in this virtual host.

  Read the article

• Understanding RedHats recommended tuned profiles

  - by espenfjo

  We are going to roll out tuned (and numad) on ~1000 servers, the majority of them being VMware servers either on NetApp or 3Par storage. According to RedHats documentation we should choose the virtual-guestprofile. What it is doing can be seen here: tuned.conf We are changing the IO scheduler to NOOP as both VMware and the NetApp/3Par should do sufficient scheduling for us. However, after investigating a bit I am not sure why they are increasing vm.dirty_ratio and kernel.sched_min_granularity_ns. As far as I have understood increasing increasing vm.dirty_ratio to 40% will mean that for a server with 20GB ram, 8GB can be dirty at any given time unless vm.dirty_writeback_centisecsis hit first. And while flushing these 8GB all IO for the application will be blocked until the dirty pages are freed. Increasing the dirty_ratio would probably mean higher write performance at peaks as we now have a larger cache, but then again when the cache fills IO will be blocked for a considerably longer time (Several seconds). The other is why they are increasing the sched_min_granularity_ns. If I understand it correctly increasing this value will decrease the number of time slices per epoch(sched_latency_ns) meaning that running tasks will get more time to finish their work. I can understand this being a very good thing for applications with very few threads, but for eg. apache or other processes with a lot of threads would this not be counter-productive?

  Read the article

• vmware esxi 5, cant create snapshots and consolidate fails, how to delete old or consolidate redo logs?

  - by Scott Szretter

  I have a VM that seems to be working ok, but when VMWare DR (or I) tries to create a snap shot, it fails, and when I view the summary page of the VM it has a warning at the top showing that the disks need to be consolidated. So I go to snapshot manager for the VM and choose consolidate (in snapshot manager, there are no snapshots actually listed by the way). If fails with this error: This virtual machine has 255 or more redo logs in a single branch of its snapshot tree. The maximum supported limit has been reached, creating new snapshots will not be allowed. To create new snapshots, please delete old snapshots or consolidate the redo logs. If I browse the data store (which has plenty of free space, 2 TB and this vm is under 40gb), in the vm folder, I do in fact see a bunch of files, numbered all the way to 0255: myvm-000255-ctk.vmdk myvm-000255-delta.vmdk myvm-000255.vmdk How can I clean all this up? Is there an SSH command line command or can I delete some of the files safely? Thanks!

  Read the article

• Webserver python update script

  - by ThePyCoder

  So i have made this website on which you can trade stocks based on real stock quotes with virtual money. The stock quotes are in a MySQL database and are updated using a python script which runs every minute or so. Now, this works fine on my local machine with xampp but how about moving the project to a commercial web server? Basically I want my page hosted by a professional company but do those kind of servers support python scripts running in the background? Because a dedicated server would be to expensive and the script does some other sql tasks too so it can't be replaced by PHP or so... So, are there any good web hosting services out there who give me the possibility of running a script in the background and hosting a website in the foreground? For what server specifications do i have to look for? Thnx in advance! PS: I've done some research, and I found a python supporting web host WITH ssh support. Is that what I need? Or is the ssh not allowed to start processes?

  Read the article

• Why does a document in Word 2007 stop recognizing the mouse after the document loses focus?

  - by alt234

  When I open a document in Word 2007, everything works fine, I can edit, highlight text, etc. However, the instant Word loses focus, when I focus back the document doesn't recognize anything the mouse does. The tabbed menu at the top seems to recognize the mouse but the document itself does not. I can scroll through via the scroll-wheel and I can type. However, typing just shows up where the mouse cursor last was before focus was taken away. I've tried clearing some word data registry keys. I've also found that some Word Add-ins can cause problems. LaserFiche is one I see mentioned a lot. As far as I can tell I have no add-ons though. Any ideas? It's crazy-annoying. UPDATE- - Word is the only program that has this problem - Typically I have Toad (Oracle DB management app), an XP virtual machine with various apps running on it, Skype, Google Talk, and maybe a handful of other programs at any given time open... Windows Media player, Outlook. - Yes, this happens even if nothing else is running. From a fresh restart as well. - I'm running Vista 64 with SP1 - According to Windows Update, I have the latest of everything. This has been happening for a couple of months now. Just never took the time to look into because I usually never have to use word.

  Read the article

• postfix not sending domain mail to mx

  - by orlandoresorts

  I'm trying to get postfix to forward email to my domain which is hosted by gmail. As I don't have any users on my server nor do I want to. Here's how I have things set up.. LEt's say you and I have a domain called mcdonalds.com the registrar has mcdonalds.com MX records pointing to gmail. (everything works for like a year) Now we set up a server to host a website. Then we create a mail account called [email protected] and send mail locally from the server using roundcube. This works. We can send mail to cnn.com we can send mail to serverfault.com we can email any/everyone. BUT we cannot send mail to our own domain mcdonalds.com So I cannot email [email protected] I cannot email [email protected] I cannot email [email protected] It gives the error: SMTP Error (450): Failed to add recipient "[email protected]" (4.1.1 : Recipient address rejected: User unknown in virtual mailbox table). I'm guessing because it is looking at the local server to find the mailbox and it doesn't exist. So how to I tell the server for any mail going to mcdonalds.com for [email protected] to send to my external mail server and NOT to lookup on the local www box we set up with zpanel. Any ideas?

  Read the article

• ubuntu 10.04 + php + postfix

  - by mononym

  I have a server I am running: Ubuntu 10.04 php 5.3.5 (fpm) Nginx I have installed postfix, and set it to loopback-only (only need to send) The problem is it is not sending. if i issue (at command line): echo "testing local delivery" | mail -s "test email to localhost" [email protected] I get the email no problem, but through PHP it does not arrive. When I send it via PHP, mail.log shows: Mar 28 10:15:04 host postfix/pickup[32102]: 435EF580D7: uid=0 from=<root> Mar 28 10:15:04 host postfix/cleanup[32229]: 435EF580D7: message-id=<20120328091504.435EF580D7@FQDN> Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: from=<root@FQDN>, size=1127, nrcpt=1 (queue active) Mar 28 10:15:04 host postfix/local[32230]: 435EF580D7: to=<root@FQDN>, orig_to=<root>, relay=local, delay=3.1, delays=3/0.01/0/0.09, dsn=2.0.0, status=sent (delivered to maildir) Mar 28 10:15:04 host postfix/qmgr[32103]: 435EF580D7: removed any help appreciated, my main.cf file: smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = FQDN alias_maps = hash:/etc/aliasesalias_database = hash:/etc/aliases myorigin = /etc/mailname #myorigin = $mydomain mydestination = FQDN, localhost.FQDN, , localhost relayhost = $mydomain mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = loopback-only virtual_alias_maps = hash:/etc/postfix/virtual home_mailbox = mail/

  Read the article

• site to listen on port 88

  - by JohnMerlino

  I want to get one of my sites to listen on port 88. In ports.conf in /etc/apache2 on ubuntu server, I add so web app can listen on port 88: NameVirtualHost *:80 Listen 80 NameVirtualHost *:88 Listen 88 I have this in my etc/apache2/apache2.conf, I have this: # Include the virtual host configurations: Include sites-enabled/ Under sites enabled, I have a file looks like this: Listen *:88 NameVirtualHost *:88 <VirtualHost *:88> ServerName dogtracking.com DocumentRoot /home/doggps/public_html/eaglegps.com/current/public <Directory /home/doggps/public_html/eaglegps.com/current/public> AllowOverride all Options -MultiViews </Directory> <LocationMatch "^/assets/.*$"> Header unset ETag FileETag None # RFC says only cache for 1 year ExpiresActive On ExpiresDefault "access plus 1 year" </LocationMatch> </VirtualHost> Then I try to restart apache: /etc/init.d/apache2 restart And I get: * Restarting web server apache2 /usr/sbin/apache2ctl: line 87: ulimit: open files: cannot modify limit: Operation not permitted Warning: DocumentRoot [/home/xtreme/Sites/DogGPS-CMS] does not exist apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName [Thu Oct 18 18:04:21 2012] [warn] NameVirtualHost *:88 has no VirtualHosts /usr/sbin/apache2ctl: line 87: ulimit: open files: cannot modify limit: Operation not permitted Warning: DocumentRoot [/home/xtreme/Sites/DogGPS-CMS] does not exist apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName [Thu Oct 18 18:04:22 2012] [warn] NameVirtualHost *:88 has no VirtualHosts (13)Permission denied: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs Action 'start' failed.

  Read the article

• VMM 2012 Adding Hosts in Trusted Forest

  - by Steve Evans

  I have two forests with a two way trust between them. VMM 2012 sits in ForestA and I can discover hosts in ForestA with no issue. When I try to discover hosts in ForestB I hit one of two issues: If I go through the GUI or use Powershell just like I normally do I get the following error on the job: Error (10407) Virtual Machine Manager could not query Active Directory Domain Services. Recommended Action Verify that the domain name and the credentials, if provided, are correct and then try the operation again. It doesn't matter which account I use. I've tried accounts from both forests, with Admin/Domain Admin permissions all over the place, etc Going through the GUI (can't find the switch in Powershell to duplicate this), I check the box "Skip AD Verification" and it causes the GUI to crash during discovery. I found an article (http://technet.microsoft.com/en-us/library/gg610641.aspx) that describes how to add a host in a disjoint namespace (even though that doesn't apply to me) and it says that VMM creates an SPN if one does not exist. So I verified that the correct SPN's exist in ForestB, that did not help the issue. I have a case open with PSS but they are stuck. I have VMM traces if anyone would like to see them. Any suggestions or ideas?

  Read the article

< Previous Page | 437 438 439 440 441 442 443 444 445 446 447 448  | Next Page >