Search Results

Search found 39473 results on 1579 pages for 'johny why'.

Page 443/1579 | < Previous Page | 439 440 441 442 443 444 445 446 447 448 449 450  | Next Page >

• SMART Status Data Interpretation - Disk Utility

  - by Mah

  Last week my external harddisk (Seagate Barracuda 1.5TB in a custom enclosure) showed signs of failure (Disk Utility SMART Pre-failure status - several bad sectors) and I decided to change it. I bought a new HDD (Seagate Barracuda 2TB) and connected it to my Ubuntu box with a SATA to USB cable that could not report SMART status. I copied all the contents of the old HDD to the new HDD (one partition with rsync, the other with parted cp) and then gently replaced the old HDD with the new one inside my aluminum enclosure. For obscure reasons after reconnecting the new HDD through the old enclosure, the Linux box could not detect my partitions. I recovered the partitions with testdisk and restarted the computer. After the restart I checked the SMART status of the new HDD an I get this: Read Error Rate --------------- Normalized 108 Worst 99 Threshold 6 Value 16737944 I got a high value on the Seek Error Rate as well. Wondering why this happens I copied 2 GB directory from one partition to the other and rechecked the SMART status (5 minutes later). This time I got the following: Read Error Rate --------------- Normalized 109 Worst 99 Threshold 6 Value 24792504 As you see there has been an increase in the error rate. I am unable to interpret these numbers. Is my new hard disk already dying? What are the acceptable values in these fields for Seagate hard disks? Then why the assessment is still good? While I could get temperature and airflow temperature data from my old HDD, I can not fetch them for the new one. I noticed that my old hdd had got really hot sometimes. Is it possible that the enclosure is killing the harddisks due to high temperature?... Thanks

  Read the article

• Forwarding a subdomain to main domain using Godaddy

  - by Ryan Hayes

  I have current blog, which was hosted on Tumblr at http://blog.ryanhayes.net. I'm moving it over to http://ryanhayes.net, and have all the 301 redirects set up for the blog entries to map to my new blog, which is hosted using Godaddy (domain included). When I try to set up a subdomain forward, I'm greeted with a nice 403 Forbidden response (as of this writing, you can see it at http://blog.ryanhayes.net. When I try to ping both the subdomain and domain, they point to the same IP address, so I know blog subdomain has at least switched over to point to the same content. I don't really understand why I would get a 403 Forbidden on the same content that I can see perfectly fine via another domain. Currently, I have a CNAME of blog pointing to @, which is how "www" is set up to forward, so I'm assuming it would do the same thing. My question is what is the proper way to set up my DNS to make the blog subdomain forward to my main domain (301) using the GoDaddy DNS manager? Bonus: What is the background on why I am getting a 403 error the current way? Forbidden You don't have permission to access / on this server. Additionally, a 403 Forbidden error was encountered while trying to use an ErrorDocument to handle the request. UPDATE 12/7/2010 Error on site has been fixed, you can no longer view it from my site.

  Read the article

• Explanation on how "Tell, Don't Ask" is considered good OO

  - by Pubby

  This blogpost was posted on Hacker News with several upvotes. Coming from C++, most of these examples seem to go against what I've been taught. Such as example #2: Bad: def check_for_overheating(system_monitor) if system_monitor.temperature > 100 system_monitor.sound_alarms end end versus good: system_monitor.check_for_overheating class SystemMonitor def check_for_overheating if temperature > 100 sound_alarms end end end The advice in C++ is that you should prefer free functions instead of member functions as they increase encapsulation. Both of these are identical semantically, so why prefer the choice that has access to more state? Example 4: Bad: def street_name(user) if user.address user.address.street_name else 'No street name on file' end end versus good: def street_name(user) user.address.street_name end class User def address @address || NullAddress.new end end class NullAddress def street_name 'No street name on file' end end Why is it the responsibility of User to format an unrelated error string? What if I want to do something besides print 'No street name on file' if it has no street? What if the street is named the same thing? Could someone enlighten me on the "Tell, Don't Ask" advantages and rationale? I am not looking for which is better, but instead trying to understand the author's viewpoint.

  Read the article

• ArchBeat Link-o-Rama for 101/10/2011

  - by Bob Rhubart

  All day, all architecture. Oracle Technology Network Architect Day - Phoenix, AZ - Dec 14. Free registration. Spend the day with your peers learning from Oracle experts in Cloud Computing, Engineered Systems, Oracle WebLogic, Oracle Coherence, Application-Driven Virtualization, and more. Registration is free, but seating is limited. Register now! Data Integration - Bad data is really the monster | Bikram Sinha "Bad data can cause huge operational failure and cost millions of dollars in terms of time and resources to clean up and validate data across multiple participating systems," says Bikram Sinha. Changing a navigation model on a page in WebCenter | Edwin Biemond Another illustrated how-to from Oracle ACE Edwin Biemond. Why do I need an Authenticator when I have an Identity Asserter? | Chris Johnson Chris Johnson responds to a user question. OOW: The Most Important Thing | Floyd Teter Oracle ACE Director Floyd Teter explains why he sees "the inclusion of Fusion Applications CRM and HCM in the Oracle Public Cloud" as the most important news to come out of Oracle OpenWorld 2011. Oracle Releases Oracle Solaris 11 | Gokhan Atil Atil offers an overview of some of the "key points" of the new Solaris 11 release. SOA Development Virtual Developer Day (On Demand) You won't get the hands-on experience available in the live event, but if you will learn learn how a SOA approach can be implemented, whether starting afresh with new services or reusing existing services. Webcast: Maximum Availability on Private Clouds - Nov 10 - 10am PT/ 1pm ET Featuring Margaret Hamburger (Director, Product Marketing, Oracle) and Joe Meeks (Director, Product Management, Oracle). Should Enterprise Architecture Teams Be More Focused on Innovation? | Richard Seroter Richard Seroter looks answers among opinions offered by Forrester analyst Brian Hopkins and Jude Umeh of CapGemini.

  Read the article

• How can I make sense of the word "Functor" from a semantic standpoint?

  - by guillaume31

  When facing new programming jargon words, I first try to reason about them from an semantic and etymological standpoint when possible (that is, when they aren't obscure acronyms). For instance, you can get the beginning of a hint of what things like Polymorphism or even Monad are about with the help of a little Greek/Latin. At the very least, once you've learned the concept, the word itself appears to go along with it well. I guess that's part of why we name things names, to make mental representations and associations more fluent. I found Functor to be a tougher nut to crack. Not so much the C++ meaning -- an object that acts (-or) as a function (funct-), but the various functional meanings (in ML, Haskell) definitely left me puzzled. From the (mathematics) Functor Wikipedia article, it seems the word was borrowed from linguistics. I think I get what a "function word" or "functor" means in that context - a word that "makes function" as opposed to a word that "makes sense". But I can't really relate that to the notion of Functor in category theory, let alone functional programming. I imagined a Functor to be something that creates functions, or behaves like a function, or short for "functional constructor", but none of those seems to fit... How do experienced functional programmers reason about this ? Do they just need any label to put in front of a concept and be fine with it ? Generally speaking, isn't it partly why advanced functional programming is hard to grasp for mere mortals compared to, say, OO -- very abstract in that you can't relate it to anything familiar ? Note that I don't need a definition of Functor, only an explanation that would allow me to relate it to something more tangible, if there is any.

  Read the article

• LiveCD Boot/Install

  - by Jon

  I have recently built a new computer and have been looking to dual-boot alongside Windows. Trying to boot/install off Ubuntu/Dedora/Arch live CDs has failed across all distros and I keep getting the error: [34.5173939] ata9.00: exception Emask 0x52 SAct 0x1 SErr 0xffffffff action 0xe frozen [34.517403] ata9: SError: {RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIR DevExch } [34.517413] ata9.00: failed command: READ FPDMA QUEUED [34.517420] ata9.00: cmd 60/08:00:00:6d:70/00:00:74:00:00/40 tag 0 ncq 4096 in [34.517420] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error) [34.517433] ata9.00: status: { DRDY } [34.667134] ata10.00 exception Emask 0x52 SAct 0x1 SErr 0xffffffff action 0xe frozen [34.667134] ata10: SError: {RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIR DevExch } [34.667153] ata10.00: failed command: IDENTIFY PACKET DEVICE [34.667159] ata10.00: cmd a1/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [34.667160] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error) [34.667170] ata10.00: status: { DRDY } I am using a new ASUS Z77 Sabertooth motherboard with a Seagate Barracuda ST1000DM003 1TB 7200RPM hard drive. I am not entirely sure why I can't even boot off the live CD? Any ideas? Hi thanks for the quick response. All Distros were direct download from their respective websites, I have tried both CD boot with all distros and USB boot with Arch only. I have just updated my BIOS as well an am still receiving the same error. The fact that it happens on CD and USB tell's me it's not an optical drive issue. All information I can find on this seems to relate to hard drives failing on already installed linux boxes or faulty SATA cables. I am a bit confused why this issue would be preventing a CD/USB boot though. Is there any more info I can provide that might help uncover the source of the problem? Cheers, Jon

  Read the article

• no way to use opendns on pppoe connection?

  - by magisterludi

  I have an old speedtouch usb modem (revision 0) and on my desktop with xubuntu 12.04 I've configured a pppoe connection. I can connect and my ISP assign an IP address and the DNS but the primary DNS address is not reachable by ping, the secondary yes but no address is resolved then I can't surf the web. Then I want to set the open DNS but there is bo way, if I change manually /etc/resolv.conf it is rewrited by some script (there is the flag usepeerdns on the configuration script, if I exclude it there is no way to assign any DNS server because resolv.conf is not read) also if I set not writable the file changing the default permission. I changed dhclient.conf with the code prepend domain-name-servers 208.67.222.222,208.67.220.220; and now if I connect by a wifi connection to my router I'm using openDNS server but ppp does not use this script as long as I can see and the DNS server is always setted by my ISP. How can I use set DNS manually to a PPP connection? Is there any way to change it after the connection? Why NetworkManager is not able to manage my dsl connection, it seems not able to manage the dsl usb cable modem. If I use pppoeconf NetworkManager doesn't start and I have to manually delete the lines added to /etc/network/interfaces because the system is not able to start with full configuration of network If I connect a modem-router to the same line I can surf with the DNS server assigned by my ISP, I can't figure why. Some suggestion? Thanks to all

  Read the article

• What's the ethos of the programming profession?

  - by mac

  I am one of those people who became professional programmer by chance, rather than by choice: I moved to a country whose main language I couldn't speak, I knew how to code... and here I am a few years later. Because of this I never really gave much a thought about the ethos of being a programmer, and working as a freelance I neither had many occasions to discuss this with fellow colleagues. Among others, Dictionary.com define the word ethos as follows: The fundamental character or spirit of a culture; the underlying sentiment that informs the beliefs, customs, or practices of a group or society; dominant assumptions of a people or period. So my question is: How would you describe the ethos of being a programmer, and why would you say so? Please note that: my question is different than this and this other ones (although you might have chosen to become a programmer because of the programmer'ethos or you might think that part of the programmer ethos is about "programming being a meaningful profession"). beside the "how/what" part of the question, there is a "why" part too! :) I would appreciate if the answer could be based not only on the idealised vision of the hero-programmer, but also on real working and life experience. Thank you in advance for your time and contributions!

  Read the article

• How to popularize Nemerle (or another programming language)?

  - by keykeeper

  Any .NET developer who is interested in different programming languages knows that F# is the most popular functional language for the .NET platform nowadays. The only fact describing the popularity of F# is the great support of Microsoft. But we are not limited with F# at all. There are some other functional languages on the .NET platform. I'm very disappointed with the fact that Nemerle isn't well-known. It's an awesome language which supports three paradigms: object-oriented, functional and meta- programming. I won't try to explain why I like it so much. The problem is that I can't use it at work. I think that only really brave companies can rely on Nemerle. It's almost unknown, that's why it's hard to find new developers for the project. Noone wants to make a first step with Nemerle if it can influence the budget what is reasonable. So, here is a question: what can I do to make Nemerle more popular? Here are my first ideas: implement open-source projects using Nemerle; make presentations on different conferences; write articles.

  Read the article

• program logic of printing the prime numbers

  - by Vignesh Vicky

  can any body help to understand this java program it just print prime n.o ,as you enter how many you want and it works good class PrimeNumbers { public static void main(String args[]) { int n, status = 1, num = 3; Scanner in = new Scanner(System.in); System.out.println("Enter the number of prime numbers you want"); n = in.nextInt(); if (n >= 1) { System.out.println("First "+n+" prime numbers are :-"); System.out.println(2); } for ( int count = 2 ; count <=n ; ) { for ( int j = 2 ; j <= Math.sqrt(num) ; j++ ) { if ( num%j == 0 ) { status = 0; break; } } if ( status != 0 ) { System.out.println(num); count++; } status = 1; num++; } } } i dont understand this for loop condition for ( int j = 2 ; j <= Math.sqrt(num) ; j++ ) why we are taking sqrt of num...which is 3....why we assumed it as 3?

  Read the article

• Oracle Fusion Applications User Experience White Papers by Anna M. Wichansky

  - by JuergenKress

  The Applications User Experience group has created a series of white papers to better communicate the world-class user experience features of the Oracle Fusion Applications, and to describe the process we used to design them. These papers not only explain why the Oracle Fusion Applications User Experience is designed the way it is, but also the data collection, modeling, and testing efforts of our unique, user-focused design process, which contributed to its refinement. The documents we are sharing with product announcement are: Applications User Experience Research and Design Process White Paper New Oracle Fusion Applications: An End-User Experience Designed for Productivity Why Oracle Expects Productivity Gains with Fusion Applications Closing the Deal: the Oracle Fusion Customer Relationship Management User Experience Oracle Fusion Human Capital Management: Designed for a Productive Workforce Get It Done Fast, Get It Done Right: The Oracle Fusion Financials User Experience Oracle Fusion Applications User Experience Design Patterns: Productivity Realized Oracle Fusion Procurement: Changing the Way You Buy and Sell Putting the User into Oracle Fusion Applications User Assistance Read the full article here. WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. BlogTwitterLinkedInMixForumWiki Technorati Tags: User Experience,Design patterns,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

• Preffered lambda syntax?

  - by Roger Alsing

  I'm playing around a bit with my own C like DSL grammar and would like some oppinions. I've reserved the use of "(...)" for invocations. eg: foo(1,2); My grammar supports "trailing closures" , pretty much like Ruby's blocks that can be passed as the last argument of an invocation. Currently my grammar support trailing closures like this: foo(1,2) { //parameterless closure passed as the last argument to foo } or foo(1,2) [x] { //closure with one argument (x) passed as the last argument to foo print (x); } The reason why I use [args] instead of (args) is that (args) is ambigious: foo(1,2) (x) { } There is no way in this case to tell if foo expects 3 arguments (int,int,closure(x)) or if foo expects 2 arguments and returns a closure with one argument(int,int) - closure(x) So thats pretty much the reason why I use [] as for now. I could change this to something like: foo(1,2) : (x) { } or foo(1,2) (x) -> { } So the actual question is, what do you think looks best? [...] is somewhat wrist unfriendly. let x = [a,b] { } Ideas?

  Read the article

• How to Manage Technical Employees

  - by Ajarn Mark Caldwell

  In my current position as Software Engineering Manager I have been through a lot of ups and downs with staffing, ranging from laying-off everyone who was on my team as we went through the great economic downturn in 2007-2008, to numerous rounds of interviewing and hiring contractors, full-time employees, and converting some contractors to employee status.  I have not yet blogged much about my experiences, but I plan to do that more in the next few months.  But before I do that, let me point you to a great article that somebody else wrote on The Unspoken Truth About Managing Geeks that really hits the target.  If you are a non-technical person who manages technical employees, you definitely have to read that article.  And if you are a technical person who has been promoted into management, this article can really help you do your job and communicate up the line of command about your team.  When you move into management with all the new and different demands put on you, it is easy to forget how things work in the tech subculture, and to lose touch with your team.  This article will help you remember what’s going on behind the scenes and perhaps explain why people who used to get along great no longer are, or why things seem to have changed since your promotion. I have to give credit to Andy Leonard (blog | twitter) for helping me find that article.  I have been reading his series of ramble-rants on managing tech teams, and the above article is linked in the first rant in the series, entitled Goodwill, Negative and Positive.  I have read a handful of his entries in this series and so far I pretty much agree with everything he has said, so of course I would encourage you to read through that series, too.

  Read the article

• Squeezing all the SEO out of a URL as possible.

  - by John Isaacks

  I am working on an ecommerce site, I told our SEO consultant that I plan to make the URL scheme: /products/<id>/<name>. This is similar to Stackoverflow's URLs which are /questions/<id>/<title>. He asked me if I could change the URL scheme to /p/<id>/<name> instead. I know why he wants this change, the word "products" isn't needed to find the correct product, and it doesn't offer any SEO, so shortening it to just p would make the relevant keywords in the <name> weigh more. His main priority is maximizing SEO, but the part that I don't think he is considering is how this effects the semantics of the site. Also having the word "products" looks like it has meaning and a reason for being there, just having a p looks chaotic and ugly to me. I also don't think it makes that much of a difference does it? Stackoverflow doesn't use /q/<id>/<title> and they do just fine, I do realize that theres many factors at play here though, not just the URL. So I want some outside opinions on which is the better way and why?

  Read the article

• Lessons From OpenId, Cardspace and Facebook Connect

  - by mark.wilcox

  (c) denise carbonell I think Johannes Ernst summarized pretty well what happened in a broad sense in regards to OpenId, Cardspace and Facebook Connect. However, I'm more interested in the lessons we can take away from this. First  - "Apple Lesson" - If user-centric identity is going to happen it's going to require not only technology but also a strong marketing campaign. I'm calling this the "Apple Lesson" because it's very similar to how Apple iPad saw success vs the tablet market. The iPad is not only a very good technology product but it was backed by a very good marketing plan. I know most people do not want to think about marketing here - but the fact is that nobody could really articulate why user-centric identity mattered in a way that the average person cared about. Second - "Facebook Lesson" - Facebook Connect solves a number of interesting problems that is easy for both consumer and service providers. For a consumer it's simple to log-in without any redirects. And while Facebook isn't perfect on privacy - no other major consumer-focused service on the Internet provides as much control about sharing identity information. From a developer perspective it is very easy to implement the SSO and fetch other identity information (if the user has given permission). This could only happen because a major company just decided to make a singular focus to make it happen. Third - "Developers Lesson" -  Facebook Social Graph API is by far the simplest API for accessing identity information which also is another reason why you're seeing such rapid growth in Facebook enabled Websites. By using a combination of URL and Javascript - the power a single HTML page now gives a developer writing Web applications is simply amazing. For example It doesn't get much simpler than this "http://api.facebook.com/mewilcox" for accessing identity. And while I can't yet share too much publicly about the specifics - the social graph API had a profound impact on me in designing our next generation APIs.  Posted via email from Virtual Identity Dialogue

  Read the article

• Thread safe GUI programming

  - by James

  I have been programming Java with swing for a couple of years now, and always accepted that GUI interactions had to happen on the Event Dispatch Thread. I recently started to use GTK+ for C applications and was unsurprised to find that GUI interactions had to be called on gtk_main. Similarly, I looked at SWT to see in what ways it was different to Swing and to see if it was worth using, and again found the UI thread idea, and I am sure that these 3 are not the only toolkits to use this model. I was wondering if there is a reason for this design i.e. what is the reason for keeping UI modifications isolated to a single thread. I can see why some modifications may cause issues (like modifying a list while it is being drawn), but I do not see why these concerns pass on to the user of the API. Is there a limit imposed by an operating system? Is there a good reason these concerns are not 'hidden' (i.e. some form of synchronization that is invisible to the user)? Is there any (even purely conceptual) way of creating a thread safe graphics library, or is such a thing actually impossible? I found this http://blogs.operationaldynamics.com/andrew/software/gnome-desktop/gtk-thread-awareness which seems to describe GTK differently to how I understood it (although my understanding was the same as many people's) How does this differ to other toolkits? Is it possible to implement this in Swing (as the EDT model does not actually prevent access from other threads, it just often leads to Exceptions)

  Read the article

• What makes a person contribute to opensource? [duplicate]

  - by Jibin

  This question already has an answer here: Why develop free, open source programs? [closed] 14 answers I know this is controversial, but.. There are many great projects like Apache Webserver or Hadoop provided by the OpenSource Community. I often feel that the people that actually benefit (financially), from these projects are developers like me, sitting in India, working for MNCs, who has never contributed anything to any opensource project so far, but earn handsomely due to my basic googling skills & the community provided documentation. Is it fair ? I mean no other industry in the world face such dilemma.Those who work get paid. I mean I almost am starting to feel guilty of taking such advantage of some thing that I contribute nothing to. I had to do projects every semester in college (we could choose projects) & I used to enjoy coding then. I want to contribute. But contributing to opensource is not a task [unlike college or office work]. And life is so busy .. Are all these opensource contributors really jobless ?[just kidding..] Could someone please share some personal experiences on how you guys started contributing or any advice on why I should contribute or what attitude in life makes you keep aside time or is it that you just crazly love writing code or is it that you just love to see your name in the contributors list or do you have a local coding group you hang out with ? Do you feel I am destined to do this ? This is my part of contributing back to the world ? Whats that basic mentality that make you guys want to contribute, while I just want to finish my work and go home. What makes you guys tick ?

  Read the article

• GDM locale problems

  - by Simón

  I have two problems with GDM on Ubuntu 10.04. The first is with locales. In my system I have defined: $ cat /etc/environment PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" LANG="es_ES.UTF-8" LANGUAGE="es_ES:es:en_US:en" $ cat /etc/default/locale LANG="es_ES.UTF-8" LANGUAGE="es_ES:es:en_US:en" $ cat /var/lib/locales/supported.d/local es_ES UTF-8 es_ES.UTF-8 UTF-8 en_US UTF-8 en_US.UTF-8 UTF-8 But when I enter in gnome desktop: $ locale LANG=es_ES LANGUAGE=es_ES:es:en_US:en LC_CTYPE="es_ES" LC_NUMERIC="es_ES" LC_TIME="es_ES" LC_COLLATE="es_ES" LC_MONETARY="es_ES" LC_MESSAGES="es_ES" LC_PAPER="es_ES" LC_NAME="es_ES" LC_ADDRESS="es_ES" LC_TELEPHONE="es_ES" LC_MEASUREMENT="es_ES" LC_IDENTIFICATION="es_ES" LC_ALL= I have deleted ~/.dmrc and I have restarted the system but nothing. GDM login screen also doesn't permit change this setting. However, in the text terminals (tty1,...): $ locale LANG=es_ES.UTF-8 LANGUAGE=es_ES:es:en_US:en LC_CTYPE="es_ES.UTF-8" LC_NUMERIC="es_ES.UTF-8" LC_TIME="es_ES.UTF-8" LC_COLLATE="es_ES.UTF-8" LC_MONETARY="es_ES.UTF-8" LC_MESSAGES="es_ES.UTF-8" LC_PAPER="es_ES.UTF-8" LC_NAME="es_ES.UTF-8" LC_ADDRESS="es_ES.UTF-8" LC_TELEPHONE="es_ES.UTF-8" LC_MEASUREMENT="es_ES.UTF-8" LC_IDENTIFICATION="es_ES.UTF-8" LC_ALL= The solution to problem is to edit .drmc file, but I think this isn't the right way. Why doesn't GDM read/apply the system locales? Why don't I see, in GDM login screen, the box to change the locale?

  Read the article

• Unity does not load when selecting Xorg open source radeon driver

  - by Teddy Thorpe

  When I select the X.org Radeon open source driver, Unity does not load. However, when I select the Proprietary AMD Driver from the official Ubuntu repository, Unity does load. Why is Unity doing this? I had no problems with switching between these drivers in Ubuntu 12.04 LTS. This started happening when I upgraded to Ubuntu 12.10. Before I ever installed the propriatery AMD driver, the X.org driver loaded Unity fine, but very sluggishly. I downloaded the AMD driver from their official website and installed that first and that is what started this problem. I removed that driver and went back to X.org and X.org didn't load Unity either. Then using Synaptic, I installed the AMD driver from the Ubuntu repositories and thats what I'm using now. I'm very confused why that downloaded AMD driver would effect X.org. I have a AMD Radeon HD 6620G. It's integrated graphics on my AMD A8-3500M APU (Accelerated Processing Unit as AMD advertises it).

  Read the article

• Trouble with touch events on iPhone

  - by MrDatabase

  I'm making a simple 2D game for iPhone. Think of the game as a ball on the screen that goes up while the user is touching the screen and falls down when the user stops touching the screen. The ball starts moving up in touchesBegan:withEvent and starts moving down in touchesEnded:withEvent. This works fine almost all the time. However on occasion the ball will keep moving up after the user stops touching... or the ball will keep moving down while the user is touching. Why is this happening? Just fyi the ball is drawn on a UIWindow. The taps are handled by a UIImageview subclass that's clearColor and takes up the entire screen. This "touchLayer" is also moved to the front of the window in the game loop. Any idea why this control scheme occasionally fails? Perhaps the touch events just aren't firing? Or they're fired out of order? Cheers!

  Read the article

• Returning Value of Radio Button Jquery [migrated]

  - by Jerry Walker

  I am trying to figure out why, when I run this code, I am getting undefined for my correct answers. $(document).ready (function () { // var answers = [["Fee","Fi","Fo"], ["La","Dee","Da"]], questions = ["Fee-ing?", "La-ing?"], corAns = ["Fee", "La"]; var counter = 0; var $facts = $('#main_ .facts_div'), $question = $facts.find('.question'), $ul = $facts.find('ul'), $btn = $('.myBtn'); $btn.on('click', function() { if (counter < questions.length) { $question.text(questions[counter]); var ansstring = $.map(answers[counter], function(value) { return '<li><input type="radio" name="ans" value="0"/>' + value + '</li>'}).join(''); $ul.html(ansstring); var currentAnswers = $('input[name="ans"]:checked').map(function() { return this.val(); }).get(); var correct = 0; if (currentAnswers[counter]==corAns[counter]) { correct++; } } else { $facts.text('You are done with the quiz ' + correct); $(this).hide(); } counter++; }); // }); It is quite long and I'm sorry about that, but I don't really know how tostrip it down. I also realize this isn't the most elegant way to do this, but I just want to know why I can't seem to get my radio values. I will add the markup as well if anyone wants.

  Read the article

• (PHP vs Python vs Perl) vs Ruby [closed]

  - by Dr.Kameleon

  OK, here's what : I've programmed in over 20 different languages and now, because of a large project I'm currently working on for Mac OS X (in Objective-C/Cocoa), I need to make a final decision on which language to use for my background scripting + plugin functionality. Definitely, one factor that'll ultimately influence my decision is which one I'm most familiar with, which is PHP (one of the ugliest languages around, which I however adore... lol), then Python / Perl (the "proven values"... )... and then Ruby (which, to me, is almost confusing and I've only played with it for some time.) Now, here's my considerations : (As previously mentioned) Being familiar with it (anyway, if X is better in my case, I really don't mind studying it from scratch...) Speed Good interaction with the Shell + ease of integration with my Cocoa application Btw, some of the reasons that made me wonder if Ruby would be a good choice is : The hype around it (although, I still don't get why; but that's probably just me...) My major competitor (we're actually talking about the same type of software here) is using Ruby for its backend scripting almost exclusively (ok, along with some BASH). Isn't Ruby considered slower e.g. than Perl? Why did he choose that? Simply, a matter of personal taste? So... your thoughts?

  Read the article

• (LWJGL) Pixel Unpack Buffer Object is Disabled? (glTextImage2D)

  - by OstlerDev

  I am trying to create a render target for my game so that I can re-render at a different screen size. But I am receiving the following error: Exception in thread "main" org.lwjgl.opengl.OpenGLException: Cannot use offsets when Pixel Unpack Buffer Object is disabled Here is the source code for my Render method: // clear screen GL11.glClear(GL11.GL_COLOR_BUFFER_BIT | GL11.GL_DEPTH_BUFFER_BIT); // Start FBO Rendering Code // The framebuffer, which regroups 0, 1, or more textures, and 0 or 1 depth buffer. int FramebufferName = GL30.glGenFramebuffers(); GL30.glBindFramebuffer(GL30.GL_FRAMEBUFFER, FramebufferName); // The texture we're going to render to int renderedTexture = glGenTextures(); // "Bind" the newly created texture : all future texture functions will modify this texture glBindTexture(GL_TEXTURE_2D, renderedTexture); // Give an empty image to OpenGL ( the last "0" ) glTexImage2D(GL_TEXTURE_2D, 0,GL_RGB, 1024, 768, 0,GL_RGB, GL_UNSIGNED_BYTE, 0); // Poor filtering. Needed ! glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MAG_FILTER, GL_NEAREST); glTexParameteri(GL_TEXTURE_2D, GL_TEXTURE_MIN_FILTER, GL_NEAREST); // Set "renderedTexture" as our colour attachement #0 GL32.glFramebufferTexture(GL30.GL_FRAMEBUFFER, GL30.GL_COLOR_ATTACHMENT0, renderedTexture, 0); // Set the list of draw buffers. IntBuffer drawBuffer = BufferUtils.createIntBuffer(20 * 20); GL20.glDrawBuffers(drawBuffer); // Always check that our framebuffer is ok if(GL30.glCheckFramebufferStatus(GL30.GL_FRAMEBUFFER) != GL30.GL_FRAMEBUFFER_COMPLETE){ System.out.println("Framebuffer was not created successfully! Exiting!"); return; } // Resets the current viewport GL11.glViewport(0, 0, scaleWidth*scale, scaleHeight*scale); GL11.glMatrixMode(GL11.GL_MODELVIEW); GL11.glLoadIdentity(); // let subsystem paint if (callback != null) { callback.frameRendering(); } // update window contents Display.update(); It is crashing on this line: glTexImage2D(GL_TEXTURE_2D, 0,GL_RGB, 1024, 768, 0,GL_RGB, GL_UNSIGNED_BYTE, 0); I am not really sure why it is crashing and looking around I have not been able to find out why. Any help or insight would be greatly welcome.

  Read the article

• How do you motivate peers to become better developers?

  - by Brian Rasmussen

  In my experience there seems to be two kinds of developers (if we simplify matters a great deal of course). On the one hand we have the developers, who may do a perfectly acceptable job, but who do not really care about the computer science part of their craft. They usually know few languages / technologies and are happy to let things stay that way. For whatever reason, they don't try to improve their computer science skills unless this is required in their current position. On the other hand, we have the geeks or the pragmatic programmers if you subscribe to that idea. They play around with other languages and technologies and usually have knowledge about several topics outside the technical domain of their current job. I would like to see more developers, who are enthusiastic about software development. If you share this point of view, what do you do to push your peers in that direction? Edit: follow-up question inspired by one of the answers: As non-managers, should we really care about this? And why/why not?

  Read the article

• Dirt Cheap Bi-Directional Antenna Wirelessly Extends Your LAN

  - by Jason Fitzpatrick

  If you’re looking for an effective way to link remote LANs without the hassle of laying cable, this DIY bi-directional antenna is a quick (and cheap) method for bringing internet access to outbuildings and other locations. Tinker Danilo Larizza needed to share internet access between apartments that are relatively close together but not hardwired–ruling out simply sharing the access via existing LAN infrastructure. His solution combines a simple scrap wire antenna array mounted inside a plastic food bin (seen here with the cover removed to show the antenna) and some coaxial cable to link the antenna to two routers. Our favorite part about his build is that he constructed the pair to establish if the antenna setup would even work in his location and intended to buy commercial antennas if it did; his Tupperware models worked so well, however, they’re now the permanent solution. Hit up the link below for more information about the project. 2.4 Ghz Directive Biquad Antenna [via Hack A Day] How To Use USB Drives With the Nexus 7 and Other Android Devices Why Does 64-Bit Windows Need a Separate “Program Files (x86)” Folder? Why Your Android Phone Isn’t Getting Operating System Updates and What You Can Do About It

  Read the article

< Previous Page | 439 440 441 442 443 444 445 446 447 448 449 450  | Next Page >