Search Results

Search found 22600 results on 904 pages for 'remote connection'.

Page 444/904 | < Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >

• Looking to get a small server – need web, PHP, PostgreSQL.

  - by Javawag

  Hi all! I'm looking to get a cheap (low end) server to serve web pages (xHTML/PHP), but I also need to be able to set up PostGreSQL on the system too. Ideally the server would have low power consumption, run Linux (I prefer Mac OS X but a Mac Mini, although the size I'm looking for, is too much money!) and be around £100 (~$160US). EDIT: Just to make it clearer, I'm looking to purchase the server hardware myself – but I want something about Mac Mini sized. I don't want to pay for hosting! Also, quick question – if it's to serve web pages from my home (standard ISP connection, no static IP!), what do I need in place to get this working. I'm guessing I would sign up with some service like no-ip, and register a domain to point to my no-ip address (then install the no-ip software on the server to update that with the current IP). I know the idea of running a server behind a normal ISP connection isn't very elegant, but I'd prefer to have the server where I can see it then pay over the odds for a hosting service where I have little to no control over what happens. Also, I could write my own server software for apps/etc to connect to as well. Anyways I'm rambling! What do you guys think?! Javawag

  Read the article

• How to stop NAT dropping idle connections?

  - by WGH

  I have a TCP connection that can be idle for many hours. The traffic is flowing from the server to the client only. One might say it's kind of push notification. My home router, however, tends to drop the connection silently after 20 minutes (the value of /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established). The server detects the loss once it tries to send anything (I assume it receives RST from the router itself). As client never sends anything, it never detects the loss. RFC 5382 "NAT Behavioral Requirements for TCP" states the following: A NAT can check if an endpoint for a session has crashed by sending a TCP keep-alive packet and receiving a TCP RST packet in response. It makes sense. It's much more effective than sending keep-alives by the host itself (as only NAT knows its own timeout). And probably not hard to implement. Is there any NAT solutions implementing this? It would be great if there was a way to enable this in iptables.

  Read the article

• How did what appears to be a virus get on my computer? (explanation of situation enclosed)

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• Can't get DNS Alias work on Ubuntu 10.04 with Apache 2

  - by Johnny

  I want to use the DNS Alias to configure one of my domain pointing to a specific directory on the server. Here is what I've done: Change the IP address in domain setting, and it works $ ping www.example.com PING example.com (124.205.62.xxx): 56 data bytes 64 bytes from 124.205.62.xxx: icmp_seq=0 ttl=48 time=53.088 ms 64 bytes from 124.205.62.xxx: icmp_seq=1 ttl=48 time=52.125 ms ^C --- example.com ping statistics --- 2 packets transmitted, 2 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 52.125/52.606/53.088/0.482 ms Add sites-available and sites-enabled $ ls -l /etc/apache2/sites-available/ total 16 -rw-r--r-- 1 root root 948 2010-04-14 03:27 default -rw-r--r-- 1 root root 7467 2010-04-14 03:27 default-ssl -rw-r--r-- 1 root root 365 2010-06-09 18:27 example.com $ ls -l /etc/apache2/sites-enabled/ total 0 lrwxrwxrwx 1 root root 26 2010-06-09 15:46 000-default -> ../sites-available/default lrwxrwxrwx 1 root root 33 2010-06-09 18:17 001-example.com -> ../sites-available/example.com But it doesn't work and when I open the browser for www.example.com, it shows an 111 error: The following error was encountered: Connection to 124.205.62.48 Failed The system returned: (111) Connection refused Here is how example.com's config: $ cat /etc/apache2/sites-enabled/001-example.com <virtualhost *:80> DocumentRoot "/vhosts/example.com/htdocs/" ServerName www.example.com ServerAlias example.com <Location /> Order Deny,Allow Deny from None Allow from all </Location> #Include /etc/phpmyadmin/apache.conf ErrorLog /vhosts/example.com/logs/error.log CustomLog /vhosts/example.com/logs/access.log combined Could you please tell me how to solve this?

  Read the article

• “NT AUTHORITY\ANONYMOUS LOGON” error in Windows 7 (ASP.NET & Web Service)

  - by Tony_Henrich

  I have an asp.net web app which works fine in Windows XP machine in a domain. I am porting it to a Windows 7 stand alone machine. The app uses a web service which makes a call to sql server. The web server (IIS 7.5) and SQL Server are on the same stand alone machine. I enabled Windows authentication for the website and web service. The web service uses a trusted connection connection string. The web service credentials uses System.Net.CredentialCache.DefaultCredentials. I noticed username, password and domainname are blank after the call! The webservice and web site use the 'Classic .NET AppPool' with NetworkServices identity. I am getting an exception "NT AUTHORITY\ANONYMOUS LOGON" in the database call in the web service. I am assuming it's related to the blank credentials. I am expecting ASPNET user to be the security token to the database. Why is this not happening? Did I miss a setting? (Usually this happens when sql server and web server are on two different machines in a domain, delegation & double hopping, but in my case everything is on a dev box)

  Read the article

• Client unable to access OWA website after temporarily changing SSL certificate on the server

  - by Lorenz Meyer

  I have the following issue: One client computer (Windows XP) cannot access the OWA website. All other client computers can (Except another one in the same remote office). How this happened: I temporarily changed the SSL certificate on the Exchange Server yesterday. After a few minutes, I reverted back, an now the same certificate that was installed for years is back again. During these few minutes, they were in OWA on this computer and got a certificate error. What exactly happens: Internet Explorer displays the error Internet Explorer cannot display the webpage, Firefox displays The connection was reset and Crome shows This webpage is not available. The connection to ... was interrupted. What I already did to try to get this working: Restart the client computer Restart the exchange server Deleted Internet Explorer browsing history In IE, Internet Options, tab Content, under Certificates deletes SSL cache Restored Internet Explorer to the default parameters I looked into certmgr.msc, but did not find a certificate related to the issue What could I do else to narrow down the origin of this problem (or better: resolve it) ? Can you give any advice ?

  Read the article

• Authentication between web server and sql server

  - by thirster42

  So, we're restructuring out development environment. We've installed SQL Server onto it's own server, and we are publishing our internal web applications onto a seperate web server. However, the problem is that for some reason the authentication of the user between the web server and sql server gets lost, resulting in the Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON' error. Where do i start troubleshooting? SQL Server is set up for TCP and remote connections.

  Read the article

• Emails not sending from outlook / OWA - Not even hitting the mail queue in exchange

  - by webnoob

  We are having an issue this morning where we can receive external emails but cannot send internal or external ones from Outlook or OWA. If I use: Send-MailMessage –From <[email protected]> –To <[email protected]> –Subject “Test #01”-Body “Just a test message.” –SMTPServer <Server-Name> –Credential <domain\user> the email is sent correctly which makes me think there is a connection issue with OWA and Outlook. However, outlook is reporting as Connected with exchange. I have checked the message tracking in exchange tools and emails sent via outlook and OWA do not appear. Nothing has changed on the server on the weekend so I don't really know where to start debugging this issue. We are using Windows SBS 2011. We only have one send connector which isn't using Smart Hosts and is set to use DNS MX records. Use external DNS is not checked and I can ping google.com etc so doesn't appear to be a DNS issue (plus the email sends from the console anyway). EDIT It appears that users using IMAP can send emails correctly, its only ones that rely on the normal exchange connection type that don't work. EDIT Emails from IMAP are hitting the email queue's where as emails from the normal exchange accounts aren't. EDIT It seems that some of the emails we tried to send yesterday sent at about 1am but now it won't work again..

  Read the article

• Problem remotely managing Exchange Server 2010

  - by Carlos

  I can't connect to the instance of exchange server 2010 through EMC on the local machine running w2k8 r2. I've checked all the default website bindings, the kerberos auth and WSMan are set to native type in powershell and I still get this error message. Connecting to remote server failed with the following error message: The WS-Management service does not support the request. It was running the command 'Discover-ExchangeServer -UseWIA $true -suppresserror $true'

  Read the article

• How do I turn on laptop (Asus R1F) with lid closed?

  - by TheDeeno

  When at home I use my laptop via remote desktop. Opening the lid just to get the laptop to power on is a PITA and is probably affecting my hinge durability. Is there a way to power on a laptop with the lid closed? Asus R1f's don't have docking stations.

  Read the article

• Windows Server 2008 ignores any change made to firewall

  - by Maurice Courtois

  I have been trying for the last 2 hours to make my Windows Server 2008 answer ping. I have tried almost every single solution I have found on the web, so far nothing work. My current setup: 2 NIC (1x Internet connection, 1x Local network) Server act as VPN server. So I set the corresponding NIC as either Public or Private. I also enable the rule for "File and Printer Sharing (Echo Request...)" for all Nic and from any IPs. I always been able to ping from the local network or the local ip while connected to the VPN. I also tried to create a specific rule for ICMP ping and disabling the firewall for all but the public nic. Regardless of all this, I still can't ping that server from Internet. Any idea suggestion what could cause this? I have the impression that when you set the server as VPN (I switch the box on when setting it up to block everything else than VPN connection) that changing anything to the firewall setting thought mmc is pointless !?!?

  Read the article

• How to override puppet class arguments in child node?

  - by Jon Skarpeteig

  I'm attempting to accomplish something like the below: node 'basenode' { class { 'puppet' : disable => false, } } node 'child' inherits 'basenode' { class { 'puppet' : disable => true, } } This gives me: err: Could not retrieve catalog from remote server: Error 400 on SERVER: Duplicate definition: Class[Puppet] is already defined How can I override this setting for this single node, and still have a parameterised class?

  Read the article

• Routing / binding 128 IPs to one server

  - by Andrew

  I have a Ubuntu server with 128 ip's (static external ips 86.xx.xx.16), and I want to crawl pages thru different ip's. The gateway is xx.xxx.xxx.1, the main ip is xx.xxx.xxx.16, and the other 128 ip's are xx.xxx.xxx.129/255. I tried this configuration in /etc/network/interfaces but I doesn't work. It work if I remove the gateway for the aliases eth0:0 and eth0:1. I think this is routing problem. auto lo iface lo inet loopback auto eth0 auto eth0:0 auto eth0:1 iface eth0 inet static address xx.xxx.xxx.16 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:0 inet static address xx.xxx.xxx.129 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:1 inet static address xx.xxx.xxx.130 netmask 255.255.255.128 gateway xx.xxx.xxx.1 Also, please tell me how to "reset" every changes that I made in networking and routing. Update: I removed the gateway and now it works. I can reach the website thru all 128 ip's. But when I try to bind a socket connection in php to a specific ip I get no answer. socket_bind($sock, "xx.xxx.xx.xxx"); socket_connect($sock, 'google.com', 80); I tryed to use a sniffer to see the packets, and I see the packet sent from binded ip to google.com but the "connection" can't be established. I don't know anything about "route" command, but I have a feeling that this is the solution.

  Read the article

• ProCurve ACL to prevent a subnet from leaving the switch

  - by kce

  I have a single HP ProCurve 2610 in a remote location that is connected in with the rest of the network via SHDSL. There are two Layer-3 networks on this segment. ACLs are setup to deny one subnet (192.0.2.0/24) from ever being able to leave the switch by virtue of being applied to port attached to the upstream connection. The other subnet should be permitted to freely leave the switch. Both subnets are on the same VLAN. Unfortunately SFlow very clearly show broadcast traffic from 192.0.2.0/24 on the upstream connection. ProCurve ACLs are not my strong suit but I feel like I'm missing something very simple here. ip access-list extended "Filter for Camera Network" deny ip 192.0.2.0 0.0.0.255 0.0.0.0 255.255.255.255 log permit ip 0.0.0.0 255.255.255.255 0.0.0.0 255.255.255.255 exit interface 24 name "DSL - UPLINK" access-group "Filter for Camera Network" in exit Unless I am mistaken traffic from 192.0.2.0/24 should be dropped as it crosses the uplink port (int 24) whereas all other traffic will be permited by the following default allow rule. What exactly am I missing here? EDIT: Firstly, why do you have two subnets contained in the same VLAN? Because that's how it was configured by a previous administrator and while it makes conceptual sense that a single subnet is "mapped" to a single VLAN there's no technical constraint that I am aware of that makes this have to be the case. Instead of filtering inbound traffic on your uplink, you should be filtering outbound traffic. The HP2600 series can only filter inbound traffic on interfaces. Should I change my filter to deny any to 192.0.2.0/24?

  Read the article

• Problem installing Exchange Server

  - by Carlos

  I can't connect to the instance of exchange server 2010 through EMC on the local machine running w2k8 r2. I've checked all the default website bindings, the kerberos auth and WSMan are set to native type in powershell and I still get this error message. Connecting to remote server failed with the following error message: The WS-Management service does not support the request. It was running the command 'Discover-ExchangeServer -UseWIA $true -suppresserror $true'

  Read the article

• Backing up my data causes my server to crash using Symantec Backup Exec 12, or How I Came to Loathe Irony

  - by Kyle Noland

  I have a Dell PowerEdge 2850 running Windows Server 2003. It is the primary file server for one of my clients. I have another server also running Windows Server 2003 that acts as the core media server for Symantec Backup Exec 12. I recently upgraded from Backup Exec 11d to 12. This upgrade was necessary because we also just upgraded from Exchange 2003 to Exchange 2007. After the upgrade I had to push-install the new version 12 Backup Exec Remote Agents to each of the servers I am backing up (about 6 total). 5 of my servers are doing just fine, faithfully completing backups every night. My file server routinely crashes. Observations: When the server crashes, it does not blue screen, it just locks up completely. Even the mouse is unresponsive. If you leave the server locked up long enough, it will eventually reboot itself and hang on the Windows splash screen. There is absolutely zero useful Event Viewer evidence of a problem. The logs go from routine logging to an Unexplained Shutdown Event the next morning when I have to hard reset the server to get it to boot. 90% of the time the server does not boot cleanly, it hangs on the Windows splash screen. I don't have any light to shed here. When the server hangs all I can do is hard reset it and try again. Even after a successful boot and chkdsk /r operation, if you reboot the machine, you have a 90% chance it won't back up again cleanly. The back story: This server started crashing during nightly backups about a month ago. I tried everything I could think of to troubleshoot the problem and eventually had to give up because I could not keep coming to the office at 4 AM to try to get the server back online. One Friday I got lucky and the server stayed up for its entire full backup. I took this opportunity to restore the full backup to a temporary server I set up and switched all my users to the temporary. Then I reloaded the ailing file server. I kept all my users on the temporary file server for about 3 weeks. I installed the same Backup Exec Remote Agent and Trend Micro A/V client on the temporary server that I was using on the regular file server. During this time, I had absolutely no problems backing up the temporary server. I tested the reloaded file server extensively. I rebooted the server once an hour every day for 3 weeks trying to make it fail. It never did. I felt confident that the reload was the answer to my problems. I moved all of the data from the temporary server back to the regular server. I got 3 nightly backups out of it before it locked up again and started the familiar failure to boot cleanly behavior. This weekend I decided to monitor the file server through the entire backup job. I RDPd into the file server and also into the server running Backup Exec. On the file server I opened the Task Manager so I could view the processes and watch CPU and memory usage. Everything was running smoothly for about 60GB worth of backup. Then I noticed that the byte count of the backup job in Backup Exec had stopped progressing. I looked back over at my RDP session into the file server, and I was getting real time updates about CPU and memory usage still - both nearly 0%, which is unusual. Backups usually hover around 40% usage for the duration of the backup job. Let me reiterate this point: The screen was refreshing and I was getting real time Task Manager updates - until I clicked on the Start menu. The screen went black and the server locked up. In truth, I think the server had already locked up, the video card just hadn't figured it out yet. I went back into my bag of trick: driving to the office and hard reseting the server over and over again when it hangs up at the Windows splash screen. I did this for 2 hours without getting a successful boot. I started panicking because I did not have a decent backup to use to get everything back onto the working temporary file server. Once I exhausted everything I knew to do, I took a deep breath, booted to the Windows Server 2003 CD and performed a repair installation of Windows. The server came back up fine, with all of my data intact. I can now reboot the server at will and it will come back up cleanly. The problem is that I'm afraid as soon as I try to back that data up again I will back at square one. So let me sum things up: Here is what I've done so far to troubleshoot this server: Deleted and recreated the RAID 5 sets. Initialized the drives. Reloaded the server with a fresh Server 2003 install. Confirmed with Dell that I have installed the latest, Dell approved BIOS and NIC drivers. Uninstalled / reinstalled the Backup Exec Remote Agent. Uninstalled the Trend Micro A/V client. Configured the server not to reboot itself after a blue screen so I can see any stop error. I used to think the server was blue screening, but since I enabled this setting I now know that the server just completely locks up. Run chkdsk /r from the Windows Recovery Console. Several errors were found and corrected, but did not help my problem. Help confirm or deny the following assumptions: There are two problems at work here. Why the server is locking up in the first place, and why the server won't boot cleanly after a lockup. This is ultimately a software problem. The server works fine and can be rebooted cleanly all day long - until the first lockup - following a fresh OS load or even a Repair installation. This is not a problem with Backup Exec in general. All of my other servers back up just fine. For the record, all of the other servers run Server 2003, and some of them house more data than the file server in question here. Any help is appreciated. The irony is almost too much to bear. Backing up my data is what is jeopardizing it.

  Read the article

• Simple vLAN setup

  - by Logan Bissonnette

  I have a basic lab environment set up to try and get 2 vLANs working in hyper-v. I have the following equipment 1 hyper-v server 1 Desktop PC 1 Managed Switch (d-link DES-3052P) 1 cheap router (DI-604) My end goal is to have 1 VM and the desktop on one vLAN with internet, and 1 VM on a separate vLAN with internet access. I am having troubles getting an internet connection to both vLANs. The switch does not have the ability to have asynchronous vLANs. This is my switch configuration Port 1 - Trunk Port - Connected to router Port 2 - Trunk Port - Connected to hyper-v Server Port 3 - Access Port- Connected to Desktop Within hyper-v I have 1 switch and 2 VMs. When the VMs are set up to use vlan ID 1, everything works fine. As soon as a VM is set up to use vlan ID 2, they lose all network connection and cannot communicate with the router anymore. I believe this is because the router is not vLAN aware. Can anyone help me with what settings need to be set up on my switch? I believe I want an egress rule so traffic leaving towards the router is untagged, is that right? If not, any ideas or hints as to what needs to be set up?

  Read the article

• Failover Cluster Quorum Failing

  - by oruchreis

  Hi, I have two nodes which boots from iscsi to implement windows 2008 cluster. And I'm using disk majority option as quorum over iscsi. But when the quorum's iscsi connection failed(May be san server reset), the failover cluster is failed too. If I reset one of the nodes, it can open, but its system disk goes offline. I cant change its status as online, because it says that its reserved by failover cluster(disk is on iscsi, beacuse iscsi boot). And this disk works as readonly. Anything on it cant be deleted or written. So, I cant rejoin the node to the cluster again. I have to reinstall windows. So, what I'm asking is, how can I implement more quorum backup? I mean, can I use both disk majority and file share majority at same time? AFAIK, every nodes also keep the quorum's copy too. But I don't know sometimes san servers goes offline. And quorum's iscsi connection and nodes' iscsi connections get lost. So, nor the quorum that is kept in the nodes neither the quorum iscsi disk is not enough to start the cluster again. I want to use both disk majority and file share majority at the same time. Can I do this? Have you any other suggestion? Regards.

  Read the article

• How to debug modsecurity_audit_log

  - by max87

  I was accessing www.example.com/RestAPI/index.php/tweets.json in my server. The modsec_audit.log showed the following error, but there is no related errors/warnings in modsec_debug.log. I could see the Internal Server error is logged in example-error_log. How can I debug this Internal Server error? --8560e90b-A-- [21/Mar/2012:07:01:52 +0000] T2l84H8AAAEAAGxPZ@QAAAAG x.x.x.x 33101 x.x.x.x 80 --8560e90b-B-- GET /RestAPI/index.php/tweets.json HTTP/1.1 Host: www.example.com User-Agent: Mozilla/5.0 (X11; Linux i686; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,/;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Cookie: __utma=159129855.1463065063.1331789485.1331789485.1331789485.1; __utmz=159129855.1331789485.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); 8cb6a414cf5ec1919864de0e80bea4da=0es7dcu0p10cocfpferb2lddi0; 8926e4f3c475bb6fcacb409299f1bd27=53cf8c5e6bf78ea45096945377e6d609 Connection: keep-alive Cache-Control: max-age=0 --8560e90b-F-- HTTP/1.0 500 Internal Server Error X-Powered-By: PHP/5.3.5 Content-Length: 0 Connection: close Content-Type: text/html; charset=UTF-8 --8560e90b-H-- Apache-Handler: php5-script Stopwatch: 1332313312358005 130428 (- - -) Producer: ModSecurity for Apache/2.5.12 (http://www.modsecurity.org/); core ruleset/2.0.5. Server: Apache --8560e90b-Z--

  Read the article

• How to access git:// protocol from GitPython

  - by Owais Lone

  I am writing an app to manage git repos using the GitPython module. It works fine for my local repos but I can't get it to work with the git:// protocol. It takes my git://address-to-repo as a directory on my filesystem. Is there a way to initiate a connection with a remote git repo?

  Read the article

• Do apps which access the network count towards my ISP's bandwidth?

  - by dotnetdev

  When an application uses the internet or even a remote network location, does this count towards the bandwidth quota of my ISP? What if the machine is virtual? Thanks

  Read the article

• Windows Vista/7 dropping Mac Server share points

  - by Hooligancat

  My Windows Vista and Windows 7 clients are having problems maintaining access to SMB shares on a Mac server. The initial connection to the server appears to be OK, as the Windows clients can see all of the server share points. However, the client randomly drops a couple of the server share points although the clients can still see the server. For example. If I have the following share points on the Mac server: Share A Share B Share C Share D Share E The Windows client can see these shares most of the time and can access them most of the time. But randomly a couple of the shares will just get dropped or go missing from the Windows client's ability to view them so I end up with something like: Share B Share D Share E All the share points are established int the same way with the same permission settings. My Mac OSX Server is set up with the following for SMB: SMB sharing enabled Standalone Server Workgroup of `CORPORATE` Allow Guest Access = YES Client connections limit = 100 Authentication: NTLMv2 & Kerberos and NTLM Code Page is Latin US (437) This is a workgroup master browser WINS registration is set to Enable WINS server (tried with setting off) Enable virtual share points for homes YES I noticed in my SMB file service log that the clients appear to connect OK, but I get the following error which implies a reset by either the server or the client: /SourceCache/samba/samba-187.9/samba/source/lib/util_sock.c:read_data(534) read_data: read failure for 4 bytes to client 192.168.0.99. = Connection reset by peer I am a bit stumped as to a direction to turn to try and get this to resolve. Continued attempts to access the server from the client will reconnect to the share points, but they inevitably get dropped again in the near future. Any and all help much appreciated.

  Read the article

• Benefit of running redis as a daemon

  - by Justin Meltzer

  I'm trying to understand what the benefit of running redis as a daemon is. The redis default configuration seems not to run redis as a daemon, but locally on Mac OS X I added it to LaunchAgents, so I'm guessing it is running as a daemon anyway? Also on my remote application which is running on a linux server, since it won't have LaunchAgents (as far as I'm aware) will I have to run redis as a daemon? What will be the benefit of doing so?

  Read the article

• Can I change the language of internal website in SBS 2008?

  - by kyrisu

  Hi, I like to manage my servers in English but my client is Polish. Is there a way to keep the main language of the server in English but get "Company Web"/OWA/Remote Access website and other publically accessible parts in Polish? P.S. I've already installed WSS language pack - this is not the issue, the issue is to have "Company Web" and other portal contents in Polish.

  Read the article

• Route return traffic to correct gateway depending on service

  - by Marnix van Valen

  On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

  Read the article

< Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >