Search Results

Search found 14745 results on 590 pages for 'setting'.

Page 444/590 | < Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• Preventing h/w RAID cards from dropping slow JBOD disks

  - by Kevin

  I'm considering buying a used SAS h/w RAID card for externally attaching HDDs to an HP ProLiant I'm setting up. However, I only require RAID functionality on some of the drives. Theoretically it should be simple to JBOD the other drives, but some of them are inexpensive SATA disks and probably cannot have TLER disabled. I'd like to know, prior to actually ordering a RAID card, whether typically RAID cards would still enforce dropping of disks that do not respond within a few seconds, even if the disk is in a JBOD, and whether there is any way to disable this. Ideally it would be nice to be able to select certain SAS ports that will be pass-through, bypassing the RAID engine entirely and just acting as an HBA for those ports. I know I could buy a separate SAS HBA but that seems like a waste of $ and is also impractical as it's a 1U server so space is extremely limited. My question then is whether the functionality I'm looking for (pass-through on certain ports or at least JBOD drives not getting themselves dropped due to slow response) is typical of proper h/w RAID cards such as PERC 5/E etc. I've browsed through the latter's manual but unfortunately, as with most user manuals, it states the obvious and doesn't state the unobvious. Thanks for any info, Kevin

  Read the article

• SQL cluster instance names for large project

  - by Sam

  We're setting up two clusters. One dev and one prod. The Production will host two SQL instances - a OLTP and a DW. The development will host 4 OLTP non-production environments and at least one DW non-production. We're working on getting more DW non-prods and possibly more OLTP systems. I'm considering a naming scheme like this, where PROJ would be 3 initials for the project name. Dev Cluster MSSQLPROJD1\D1 (DEV) MSSQLPROJD2\D2 (TEST) MSSQLPROJD3\D3 (QA) MSSQLPROJD4\D4 (STAGE) MSSQLPROJD5\D5 (DW) Prd Cluster MSSQLPROJP1\P1 (PRD) MSSQLPROJP2\P2 (DW) To the left of the slash, each name must be unique network wide. On each server, the instance name, to the right of the slash, must be unique. Any thoughts on this? I'm trying to avoid having instance names drifting from reality as the project progresses - say we change what we call a certain environment or want to repurpose one. Then we can update a listing of the purposes for the instances and be done with it. How has a scheme like this worked out for you? Maybe you do things another way in your shop - tell me about it. Thanks.

  Read the article

• SharePoint, Exchange and Incoming Emails Without Directory Management Services

  - by Nariman

  Trying to keep this as simple as possible. We've already created the email accounts that we need (e.g. account[1-20]@domain.com) on Exchange/AD. We'd like to now enable incoming emails on SharePoint 2007 lists corresponding to these accounts. My thinking is we don’t need to configure Directory Management Services [2] – the architecture will be simpler without it and the application doesn’t require these services. However, we still need to route messages from Exchange to either local SMTP services (via the connector described in the articles below) or by user-specific drop-folder settings (if permitted by Exchange). So the question is: can we instruct Exchange to use a drop folder just for accounts account[1-20]@domain.com? or do we need to change the accounts to account[1-20]@sharepointsmtp.domain.com and re-route those message to the local SMTP service that will drop them on disk? I've read the material below. [1] - http://www.combined-knowledge.com/Downloads/2007/How%20to%20configure%20Email%20Enabled%20Lists%20in%20Moss2007%20RTM%20using%20Exchange%202007.pdf http://social.msdn.microsoft.com/Forums/en/sharepointdevelopment/thread/91e0c3d2-afe6-469d-b1bc-6ae7a9aa287e http://gj80blogtech.blogspot.com/2009/12/configure-incoming-email-setting-in.html http://www.jasonslater.co.uk/2007/08/10/configuring-incoming-mail-on-moss-2007-and-exchange-2007/ http://technet.microsoft.com/en-us/library/cc262947%28office.12%29.aspx http://technet.microsoft.com/en-us/library/cc263260%28office.12%29.aspx [2] – http://graycloud.com/sharepoint/incoming-mail-configuration-what-permissions-are-require-t39483.html

  Read the article

• Overriding HOMEDRIVE and HOMEPATH as a Windows 7 user

  - by MikeC

  My employer has an Active Directory group policy which sets my Windows 7 laptop HOMEDRIVE to "M:" (a mapped network drive) and my HOMEPATH to "\". Since I have read-only permissions for the root of that shared drive, I cannot create files or directories in my windows home directory. My attempts to work with the IT department have been unsuccessful. Is there a way for me to globally change these envars at boot or login time? I need for all applications to use alternate values (such as "C:" and "\Users\myname"). I have some installed utilities (like gvim and others) that store preference files in the user's home directory. IMPORTANT: Changing these envars under "System Properties Environment Variables" does not work. I have tried setting these as both User and System Variables (including a reboot). TypingSET HOMEin a DOS window clearly shows that my settings are ignored. Also, using "Start in" in a Windows shortcut will also not solve this, as I need things like Explorer context menu items (like "Edit with Vim") to operate correctly. I do have admin rights on this company laptop, but I am not a Win7 guru. Back in the day, a boot script would have solved this in a minute. Is it even possible today? Thanks.

  Read the article

• Nginx : Proper use of limit_req_zone and limit_req

  - by xperator

  I have 2 website running on VPS. Their purpose is sharing music files and publishing news. Both of them use wordpress. What I am trying is that I want to prevent little hackers from flooding the webserver and putting stress on the server to make it crash. The problem is that after using limit_req_zone and limit_req my website became very slow. Browsing Wordpress control panel takes a long long time. I tried changing values but it didn't improve much. I guess the problem is Wordpress because it's the only script I am using on both front and back end. Here is the last setting which seems to be more responsive than others : limit_req_zone $binary_remote_addr zone=flood:5m rate=10r/m; location ~ \.php$ { limit_req zone=flood burst=100 nodelay; } What are the optimal values that should be used in my case (wp) ? I want the website have it's normal behavior, On the other hand stopping lifeless people from flooding. Another question, Is it safe and enough to use limit_req only on php files ?

  Read the article

• error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7]

  - by brazorf

  This error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] error is happening after i changed router. Actually, i found out that this error just happens on a ctrl+c signal, so it could be not representative about the error itself. The command i run is very basic: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory Basically, the rsync just stuck there and nothing's happening, until i ctrl+c. After interrupting the process i got the error in subject. I past the whole thing here: rsync -avvvvz --delete /source/path/ username@host:/path/to/direectory cmd=<NULL> machine=HOSTNAME user=username path=/path/to/direectory cmd[0]=ssh cmd[1]=-l cmd[2]=username cmd[3]=HOSTNAME cmd[4]=rsync cmd[5]=--server cmd[6]=-vvvvlogDtprze.iLsf cmd[7]=--delete cmd[8]=. cmd[9]=/path/to/direectory opening connection using: ssh -l username HOSTNAME rsync --server -vvvvlogDtprze.iLsf --delete . /path/to/direectory note: iconv_open("UTF-8", "UTF-8") succeeded. ^C[sender] _exit_cleanup(code=20, file=rsync.c, line=541): entered rsync error: unexplained error (code 130) at rsync.c(541) [sender=3.0.7] [sender] _exit_cleanup(code=20, file=rsync.c, line=541): about to call exit(130) The authentication runs on ssh via rsa key. I tried basic troubleshoot such as: ping the remote host ssh -l username remote.host check software firewall logs i asked the remote host sysadmin to check for logs, and when i run that command a ssh connection is actually being established and i can state there is no comunication/authentication/name resolution issue here. Rolling back to old router make this work again. Both client and server are running ubuntu 10.04. Try to take a look at my router configuration, where i'm no experienced at all, but i didnt see any "suspect" (what i was looking for is firewall blocking something) setting. The router itself is DLINK DVA-G3670B. Any suggestion? Thank You F.

  Read the article

• VPN on a ubuntu server limited to certain ips

  - by Hultner

  I got an server running Ubuntu Server 9.10 and I need access to it and other parts of my network sometimes when not at home. There's two places I need to access the VPN from. One of the places to an static IP and the other got an dynamic but with DynDNS setup so I can always get the current IP if I want to. Now when it comes to servers people call me kinda paranoid but security is always my number one priority and I never like to allow access to the server outside the network therefor I have two things I have to have on this VPN. One it shouldn't be accessiable from any other IP then these 2 and two it has to use a very secure key so it will be virtually impossible to bruteforce even from the said IP´s. I have no experience what so ever in setting up VPNs, I have used SSH tunneling but never an actuall VPN. So what would be the best, most stable, safest and performance effiecent way to set this up on a Ubuntu Server? Is it possible or should I just set up some kind of SSH Tunnel instead? Thanks on beforehand for answers.

  Read the article

• port forwarding problem

  - by Claudiu

  I want to set up an svn server on my computer, so it's available from anywhere. I think I set up the repository correctly, using CollabSVN. If I go to Repo-Browser with TortoiseSVN and point it to svn://localhost:3690, it shows the proper repository. The problem now is that I'm behind a router. My local IP is 192.168.1.45 . Doing svn://192.168.1.45:3690 also works. My global IP is, say, x.x.x.x. Just doing svn://x.x.x.x:3690 doesn't work, which makes sense, since I have to set up port forwarding. I'm using a Verizon router. Using their web interface (on 192.168.1.1) I added the following port forwarding rule: IP Address forward to: 192.168.1.45 Source Ports: Any Dest Ports: 3690 Forward to: 3690 Protocol: TCP However, even after applying this rule, going to svn://x.x.x.x:3690 doesn't work. It takes a few seconds to fail, then says that the connection couldn't be established because the server connected to didn't respond properly after a period of time. What's interesting is that a random port, like svn://x.x.x.x:36904 fails immediately, saying that the target machine actively refused the connection. So I figure that the forwarding rule did something, but not fully what was necessary. Any ideas on how to get this working? The router model is MI424-WR and the firmware version is 4.0.16.1.56.0.10.12.3. UPDATE: I also tried setting destination port to 45000, and still forwarding to 3690, in case something was wrong w/ the lower-numbered ports, but to no avail. I also tried port 80 to port 3690, still all in vain.

  Read the article

• Password Authentication Fails - NTLMv2

  - by JMeterX

  Environment: Windows 2000 sp4 EDIT: Domain Controller with no trust setup with the Win2008 Server Windows XP machines Windows 2008 Server Netapp NAS Problem: We have a shared folder that resides on a NAS using a Windows 2008 AD for the authentication with the proper permissions setup. When the Windows 2000 machine tries to open the share residing on the Win2008 machine, it is prompted for a username and password. Upon entering the credentials it continuously re-asks for credentials. Important Details: The Windows 2000 machine can ping both the XP machines and the Windows 2008 Server The Windows 2008 machine is mandated to only use NTLMv2 The Windows 2000 machine was originally set to NTLM but was recently switched to NTLMv2 if negotiated for the purpose of trying to connect to the share. As I am sure it will come up, we are using Windows 2000 because of contractual obligations Questions: Why is password Authentication failing in this case? After setting a GPO for the Win2000 machine for it to use NTLMv2, do we need to reboot the machine for the changes to take affect? We used SECEDIT to update the GPOs without rebooting. UPDATE We checked both of the 2008 Domain Controllers to find an error code. We received: Microsoft_Auth_Package_V1_0 0xc000006a Event ID: 4776 I know this to be an authentication error via THIS article "The value provided as the current password is not correct" We know this password to be correct, but since these two domains (Win2000 & Win2008) do not have a trust setup what authentication account needs to be used? One that resides on the Win2000 hosted domain?

  Read the article

• Tools to manage sql 2008 database mirroring?

  - by lemkepf

  We are going to be moving about 20 databases that live on a single instance of sql 2000 to a sql 2008 r2 environment with database mirroring. What I'm looking for is a tool or scripts that will help me manage the conversion and management of those 20db's onto this new mirrored environment easily. There are many steps in setting each DB up and I want to automate as much as possible. Edit: Here are the steps I've been doing manually: Create the same username/passwords from the old sql 2000 server onto new sql 2008 server. Then sync those users/passwords onto the other sql 2008 server with the same SSID's so when we do the db backup and restore they match up. Take a backup of each sql 2000 db's. Copy them to server A. Restore the backup to server A. Backup from server a, copy to server b, restore there. Run the mirror "configure security" wizard. Start mirroring. I've love to be able to script this out or have a tool that does it for me. Thanks! Paul

  Read the article

• SFTP, Chroot problems on Redhat

  - by Curtis_w

  I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

  Read the article

• How to set up multiple SSIDs with bandwidth limiting on a single wireless router?

  - by Rahul Narain

  I have an Asus WL-520GU wireless router connected to a cable modem that I use for wireless internet access in my apartment. I would like to set it up so that it provides two SSIDs: one secured and password-protected for my regular use, and a "guest" SSID that's unsecured but throttled to, say, 10% of the available bandwidth. What is the most straightforward way to do this? I've been looking into DD-WRT and Tomato, both of which support my router. DD-WRT supports setting up multiple SSIDs using the GUI, but I don't know if it's possible to limit the bandwidth of each SSID independently; point #12 in this FAQ thread says it's not possible to limit by day or by MAC address, which is discouraging but not conclusive. Tomato allows bandwidth limits in its QoS settings, going by the screenshot here, but multiple SSID support is still experimental and it doesn't look like it will work with the encryption settings or bandwidth limits in the GUI. I'd like to know a good way to do this which gives me the fewest opportunities for screwing up. I'm no stranger to the command line, if that turns out to be what's necessary, but if so, please explain what the commands are doing because I don't have a good mental model of what needs to happen to set this up.

  Read the article

• Cant kill process on Windows Server 2008!! - Thread in Wait:Executive State

  - by adrian

  I hope someone can help me with our issue we are having. We have a major issue with a process that we can not kill and the only way to get rid of the process is to reboot the machine. I have tried killing it from the normal task manager but no joy. I have tried killing it using the taskkill /F command from a command prompt and no joy. The command reports as sucessful but the process remains. I have tried to start task manager with system rights by calling "psexec -s -i -d taskmgr" and attempting to kill the process but no joy I have tried killing it from Process Explorer but again the process remains. I have tried creating a scheduled task that runs under the SYSTEM name to kill the task but that also does not kill it : schtasks /create /ru system /sc once /st 13:16 /tn test1 /tr "taskkill /F /PID 1576" /it Nothing I do will kill this process. Even logging off and logging back on will not kill this process. Using Process Explorer I notice that there is on stubborn thread that is in the Wait:Executive state. I have tried to kill this thread using Process Explorer but again no joy. We are using Windows Server 2008 R2 64-Bit. The server is brand new and windows is freshly installed. Now heres the thing. We have brought two identical servers from Dell with the same specs and the same OS installed and I can not replicate this issue on the other server. Only on this server, under certain circumstances does this server process hang and can not be restarted! I have also changed the compatability mode by setting it the process to "Windows 2003" but this has not helped. I have noticed in Process Explorer that DEP is turned on but im not sure this has got any bearing on the issue ot not. Please, can someone help??

  Read the article

• DVD Share on Vista Home Premium Failing

  - by hpunyon

  UPDATE: - I can't find any Local Policy Editor for Vista Home Premium, as suggested. - I did learn about registry keys: allocatecdroms, allocatefloppies, allocatedasd and tried adding these keys (individually and collectively) and setting them to both 0 or 1. There was no positive affect on read access to the DVD root folder - always Access Denied. ORIGINAL POST: Failing read access to the root folder of a DVD drive in Vista Home Premium laptop using the Guest account - Access Denied. The client is an XP Home PC that can see, but not access, the data in the share. I'm only trying to read the data DVD - not trying to write/burn anything. On the Vista laptop, I have: All Firewalls and Antivirus disabled.UAC disabled. Password checking disabled. "Advanced Shared" the DVD drive, with "Everyone" having full-access permissions to the share. Tried adding Guest and Anonymous users having full-access permissions to the share. RestrictAnonymous=0 set in the registry. Both PC's are in the same workgroup (MSHOME) The XP Home client sees the shared DVD in \Vista_Hostname\ but when I double click the drive icon on the client, I get a popup that access is denied, check with the administrator, etc. I can share other folders on the Vista PC and see and READ these from the XP Home client. If I enable password checking on the Vista side, I get a user/password popup, and I can authenticate (using my known Vista account, that happens to have Admin rights) and then I can get to see and read the DVD data. I need to open this up so that the (default) Guest user can see and access the DVD data files.

  Read the article

• iptables configuration under ubuntu

  - by aioobe

  I'm following a tutorial on setting up a dns-tunnel. I've run into the following instruction: Now you need to enable forwarding on this server. I use iptables to implement masquerading. There are many HOWTOs about this (a simple one, for example). On Debian, the configuration file for iptables is in /var/lib/iptables/active. The relevant bit is: *nat :PREROUTING ACCEPT [6:1596] :POSTROUTING ACCEPT [1:76] :OUTPUT ACCEPT [1:76] -A POSTROUTING -s 10.0.0.0/8 -j MASQUERADE COMMIT Restart iptables: /etc/init.d/iptables restart The problem is that I don't have any /var/lib/iptables/active. (I'm on ubuntu.) How can I accomplish this? I suspect that I should just interact with the iptables command somehow but I have no clue what to write. Best would probably be if I could put the commands in a script somehow I suppose. (A side-note. If I execute a few iptables-commands it wont be there for ever, right? The rules will be discarded on reboot?)

  Read the article

• Getting prompted for password accessing page through script even when client and server are in same

  - by Munawar

  I'm trying to pull up an internal webpage in automated fashion using the methods in 'Internetexplorer.Application' using vbscript. But I'm getting prompted for password, although the client and the server both are in the same domain. Predictably when I manually try to access the web page, I don't have any problem. Only when I try using cscript.exe or iexplore.exe, I get prompted. I'm trying to automate some of the smoke test we do after a new build is deployed. But this password prompt is getting in the way. Following are the system specs Client machine - IE 7.0, OS is Windows server 2003 Server machine - Windows Server 2008 Both are in the same domain. So far I've unsuccessfully tried following to automate the password input system.diagnostics.process.start var WinHttpReq = new ActiveXObject("WinHttp.WinHttpRequest.5.1"); WinHttpReq.Open("GET", "http://website", false); WinHttpReq.SetCredentials("username", "password", 0); Nothing seems to work I checked in IIS. we have only anonymous and forms authentication enabled Is there any configuration setting in the client machine that can be tweaked to bypass this, although I'd hate to do it since you step on the toes of twenty people trying to do that. Preferable way would be to programmatically input it if its possible. Also, if you can suggest a more appropriate forum, that'd be great too. Please help.

  Read the article

• Authority Information Access local path being ignored

  - by Kevin

  I have a CA set up in Server 2008 R2, and generally it is working, but I can't control the local path/filename it writes its own certificate to for the Authority Information Access publishing. Here's a screen shot of the dialog I'm trying to set this on: From these settings I would expect to get the file: C:\Windows\system32\CertSrv\CertEnroll\DAMNIT.crt But instead I get: C:\Windows\system32\CertSrv\CertEnroll\SERVER.domain.com_My Issuing Authority(1).crt Of course, the actual change shown wouldn't be very useful, but it's illustrative; no matter what path/filename I use, it always lands up in the same place and with the same name. I actually wanted to change the name from <ServerDNSName>_<CaName><CertificateName>.crt to <CaName><CertificateName>.crt, since the latter corresponds to the HTTP URL whereas the former does not. Admittedly, I haven't set up many CAs so perhaps I'm just deluded as to what this dialog is supposed to be setting, but if so this is notoriously bad UI design. (Incidentally, I have a couple other complaints with the same dialog.) What's going on here and is there some way to get the filename pattern I want?

  Read the article

• Can't Configure IBM 8275-416 Switch Via Serial

  - by Sean M

  I am attempting to configure an IBM 8275-416 switch (I found a manual here) via serial connection. However, when I connect with HyperTerminal, the output contains a lot of garbage characters. It's pretty much unusable, because there's enough layout-breaking text-gunk that it's very difficult to determine what's actually being displayed. . I was able to reset the switch to factory defaults via the terminal interface, so I know that it's not entirely broken. It also performs basic functions all right (i.e., you plug in clients and Ethernet cables - they can connect to clients plugged into other ports) - but I'd like it to do more than that (VLANs yay). I don't know if its in-band UI is operational or not, because I can't get the terminal interface to behave well enough to properly turn on the web/SNMP UI. So that's not available. Things I've tried: - Changing the encoding: HyperTerminal lets me choose between Standard JIS and Shift-JIS. Neither setting fixes the issue. - Checking emulation settings: The manual demands VT100, 19200 baud, 8 data bits, and such: I have faithfully applied these settings, both in HyperTerminal's settings and in the properties of the COM1 port in Device Manager (connecting from a Windows machine). - Restoring to factory defaults: See above. Things that it could be, but that seem unlikely: - Cabling: Couldn't find a proper null-modem cable, so used two 232-to-RJ45 adapters. But if it was a problem with the cable, wouldn't it be more likely to not connect or do input at all, rather than just garble the text? Since I was actually able to perform the reset-to-factory defaults operation, I don't think it's this. - Device as a whole broken: It is a decade and change old, so it's possible that it's just dying slowly. Again, though, it seems like there would be more symptoms than just garbled text in the terminal. What else can I try to get a sane interface to this switch?

  Read the article

• 'Bug in Mailman version 2.1.12'

  - by davorg

  I'm working on setting up a server running Plesk 10.4.4 Update #13 on Centos 6.2. I've configured Mailman and now I want to set up some mailing lists. I've created a list in the Plesk control panel, but when I try to administer the new list (by visiting http://lists.[domain].com/mailman/admin/[listname] I see the following error: Bug in Mailman version 2.1.12 We're sorry, we hit a bug! Please inform the webmaster for this site of this problem. Printing of traceback and other system information has been explicitly inhibited, but the webmaster can find this information in the Mailman error logs. I see exactly the same error if I try to go to the list info page at http://lists.[domain].com/mailman/listinfo/[listname]. I would follow the instructions and look in the error logs, but I can't find them. I would expect to find a file at /var/log/mailman/error, but there's nothing there. My test list seems to work correctly. It sends all the expected email. It's just the web pages for the list that seem to be broken. Has anyone else seen this? Any suggestions for tracking down and fixing the problem? p.s. I think I've chosen the correct Stack Exchange site, but it this question would be better asked elsewhere, please let me know. Update: I got to the bottom of this, so I'm documenting the answer in case anyone else has the same problem. The fact that I couldn't find the error log was the clue. The problem was that the Mailman process didn't have permissions to create an error log. And it seems that if Mailman can't create an error log then it will respond to any web request with this error page. Creating an error log file (in /var/log/mailman/error) and giving it the correct permissions fixed the problem.

  Read the article

• Virtual host redirects to localhost in Ubuntu

  - by Salman

  I have recently configured Virtual Host in my Ubuntu 11.10. But whatever site i type, it always redirects to the localhost page. This is my "our-test-site" file: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/zftut/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/zftut/public/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> and this is my, "etc/hosts" file: 127.0.0.1 localhost 127.0.0.1 our-test-site.local 127.0.0.1 zftut.local 127.0.1.1 System.B System Now when I try to go for "zftut.local", it redirects me to localhost page, showing me this: It works! This is the default web page for this server. The web server software is running but no content has been added, yet. What am I doing wrong? I refered "this" tutorial for setting up virtual host.

  Read the article

• Best Practices for adding Exchange Archive to current 3 server setup

  - by ADquestion

  I'm looking to add an Archive Database (which I know is just a Mailbox Database) to our current Exchange 2010 environment. I have done this in the past at a previous job, but we had a simpler setup than at this current job. I've been trying to find some best practices to make sure it's setup in an ideal way, but so far not finding the details I would prefer. Hoping someone on here can give me a few pointers. Currently we have a 3 server setup, Server1, Server2 and Server3. Three databases of course, DB1, DB2 and DB3. We have a DAG setup between them. Server1 has DB1 and DB3 on it, DB1 is not active, DB3 is active. Server2 has DB1 and DB2 on it, both are active. Server3 has DB2 and DB3 on it, both are not active. All three servers are virtual (VMware). Each one is setup identical to the other as follows: C:\ 60GB - OS E:\ 600GB - DB (currently only 90GB used, pointing to Datastore just for Server2) F:\ 200GB - Log (2GB used, pointing to same Datastore as above) G:\ 200GB - Restore (0 used, pointing to same Datastore as above) The drives are all set to Thin Provisioning, and it looks as though I have 600GB of available space. They have not been on Exchange that long and only have about 70GB worth of PSTs to import back in that will be going to the Archive Database, plus anything older than 2 years from their current inbox that will be moved into there. I was considering placing the Archive DB on the E:\ drive of Server3 (only) like the current DB, but wasn't sure if that was acceptable. I don't plan on setting the Archive DB up with the DAG, just plan on having it as a single repository for older emails and manually back it up every now and then. If anyone has any suggestions on this I would appreciate it the input. I've done it on a slightly smaller scale before and it worked well, but like to think it through before pulling the trigger, especially at a new job. :) Thanks again!

  Read the article

• Debian Stable: Can't update kernel, libc won't update.

  - by pascal

  I use Debian Stable (squeeze) on a virtual host where I can't touch the kernel, it's stuck (and will be for some time as support told me) at Linux 2.6.18-028stab070.3 #1 SMP Wed Jul 21 18:33:27 MSD 2010 x86_64 So when I try to update, several packages fail with FATAL: kernel too old for example Preparing to replace libgcc1 1:4.6.0-11 (using .../libgcc1_1%3a4.6.1-1_amd64.deb) ... Unpacking replacement libgcc1 ... Setting up libgcc1 (1:4.6.1-1) ... FATAL: kernel too old Segmentation fault dpkg: error processing libgcc1 (--configure): subprocess installed post-installation script returned error exit status 139 and some version chaos ensued: The following packages have unmet dependencies: libc-dev-bin : Depends: libc6 (> 2.13) but 2.11.2-13 is installed libc6 : Depends: libc-bin (= 2.11.2-13) but 2.13-5 is installed libc6-dev : Depends: libc6 (= 2.13-5) but 2.11.2-13 is installed libquadmath0 : Depends: gcc-4.6-base (= 4.6.0-2) but 4.6.0-11 is installed libstdc++6 : Depends: gcc-4.6-base (= 4.6.0-2) but 4.6.0-11 is installed locales : Depends: glibc-2.13-1 What should I do? I want to keep the system up-to-date, so I want to pin as few packets as possible, but I also don't want to have to compile anything manually. Trying to pin the status quo and figured out where the error came from: ldconfig segfaults. -v doesn't print anything more so I can't tell what's the actual problem. # ldconfig FATAL: kernel too old

  Read the article

• Sharing a folder with Nautilus and NTFS external drive gets errors

  - by TheLQ

  I am trying to share a folder in Lubuntu over a network that's on an external NTFS drive. Due to the system that I have (rotating backup disks) this is probably the second time that the drive would of been mounted. Its manually mounted with a simple (for example) mount /dev/sdb1 /media/BACKUP On an internal NTFS disk I have successfully setup a network share and can access it. However on the external disk I can't from any other Windows computer. When setting up the share Nautilus said that it needs to change the other's permissions to allow for other users to write. However afterwords its still blank. Changing it to Read and Write just changes back to blank. Chowning the entire /media folder recursively and trying didn't work. Running PCManFM as root and changing didn't work. Adding "public=yes" to smb.conf and restarting didn't work. I'm out of idea's on what to do. What's weird is that it worked just fine on an internal NTFS disk, so why not the external one? Any solutions need to be able to managed inside of a gui (preferably Nautilus) as the person managing the machine isn't as tech savvy. Thanks

  Read the article

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

< Previous Page | 440 441 442 443 444 445 446 447 448 449 450 451  | Next Page >