Search Results

Search found 12376 results on 496 pages for 'active pattern'.

Page 445/496 | < Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• PPTP VPN Not Working - Peer failed CHAP authentication, PTY read or GRE write failed

  - by armani

  Brand-new install of CentOS 6.3. Followed this guide: http://www.members.optushome.com.au/~wskwok/poptop_ads_howto_1.htm And I got PPTPd running [v1.3.4]. I got the VPN to authenticate users against our Active Directory using winbind, smb, etc. All my tests to see if I'm still authenticated to the AD server pass ["kinit -V [email protected]", "smbclient", "wbinfo -t"]. VPN users were able to connect for like . . . an hour. I tried connecting from my Android phone using domain credentials and saw that I got an IP allocated for internal VPN users [which I've since changed the range, but even setting it back to the initial doesn't work]. Ever since then, no matter what settings I try, I pretty much consistently get this in my /var/log/messages [and the VPN client fails]: [root@vpn2 ~]# tail /var/log/messages Aug 31 15:57:22 vpn2 pppd[18386]: pppd 2.4.5 started by root, uid 0 Aug 31 15:57:22 vpn2 pppd[18386]: Using interface ppp0 Aug 31 15:57:22 vpn2 pppd[18386]: Connect: ppp0 <--> /dev/pts/1 Aug 31 15:57:22 vpn2 pptpd[18385]: GRE: Bad checksum from pppd. Aug 31 15:57:24 vpn2 pppd[18386]: Peer armaniadm failed CHAP authentication Aug 31 15:57:24 vpn2 pppd[18386]: Connection terminated. Aug 31 15:57:24 vpn2 pppd[18386]: Exit. Aug 31 15:57:24 vpn2 pptpd[18385]: GRE: read(fd=6,buffer=8059660,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: Client 208.54.86.242 control connection finished Now before you go blaming the firewall [all other forum posts I find seem to go there], this VPN server is on our DMZ network. We're using a Juniper SSG-5 Gateway, and I've assigned a WAN IP to the VPN box itself, zoned into the DMZ zone. Then, I have full "Any IP / Any Protocol" open traffic rules between DMZ<--Untrust Zone, and DMZ<--Trust Zone. I'll limit this later to just the authenticating traffic it needs, but for now I think we can rule out the firewall blocking anything. Here's my /etc/pptpd.conf [omitting comments]: option /etc/ppp/options.pptpd logwtmp localip [EXTERNAL_IP_ADDRESS] remoteip [ANOTHER_EXTERNAL_IP_ADDRESS, AND HAVE TRIED AN ARBITRARY GROUP LIKE 5.5.0.0-100] Here's my /etc/ppp/options.pptpd.conf [omitting comments]: name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 192.168.200.42 # This is our internal domain controller ms-wins 192.168.200.42 proxyarp lock nobsdcomp novj novjccomp nologfd auth nodefaultroute plugin winbind.so ntlm_auth-helper "/usr/bin/ntlm_auth --helper-protocol=ntlm-server-1" Any help is GREATLY appreciated. I can give you any more info you need to know, and it's a new test server, so I can perform any tests/reboots required to get it up and going. Thanks a ton.

  Read the article

• dd-wrt router firmware QoS troubleshooting

  - by Jeff Atwood

  I've been using the dd-wrt firmware on my router and I like it a lot! But -- I'm not sure the quality of service (QoS) is working on it. I have it set up as follows: http, port 80 -- Premium bittorrent, port 6969 -- Bulk https, port 443 -- Premium dns, port 53 -- Premium Per the QoS documentation, these levels are: bandwidth is allocated based on the following percentages of uplink and downlink values for each class: Exempt: 100mbps - ignores global limits. Premium: 75% - 100% Express: 15% - 100% Standard: 10% - 100% Bulk: 1.5% - 100% This doesn't entirely seem to work, though -- with busy torrents going I get major pauses in my web browsing which sucks! The QoS documentation gives some steps to check the QoS ... What you'll be interested to look at will be the first set of source and destination IP, including the port numbers. Next the presence of l7proto and the "mark" field. The entries indicate the current live connection QoS priority applied on them based on the "mark" field. The "mark" values correspond to the following Exempt: 100 Premium: 10 Express: 20 Standard: 30 Bulk: 40 (no QoS matched): 0 You may see "mark=0" for some l7proto service even though they are in configured in the list of QoS rules. This may mean that the layer 7 pattern matching system didn't match a new or changed header for that protocol. Custom service on port matches will usually take care of these. On port 6969 (bittorrent) I see a weird mixture of stuff with mark=0 and mark=40 like so cat /proc/net/ip_conntrack udp 17 105 src=98.162.182.42 dst=1.2.3.4 sport=64512 dport=6969 packets=3 bytes=290 src=10.0.0.2 dst=98.162.182.42 sport=6969 dport=64512 packets=4 bytes=202 [ASSURED] mark=0 secmark=0 use=1 tcp 6 117 TIME_WAIT src=98.248.173.174 dst=1.2.3.4 sport=51114 dport=6969 packets=12 bytes=704 src=10.0.0.2 dst=98.248.173.174 sport=6969 dport=51114 packets=10 bytes=440 [ASSURED] mark=40 secmark=0 use=1 tcp 6 598 ESTABLISHED src=165.132.128.201 dst=1.2.3.4 sport=57218 dport=6969 packets=8024 bytes=9919881 src=10.0.0.2 dst=165.132.128.201 sport=6969 dport=57218 packets=4211 bytes=239607 [ASSURED] mark=0 secmark=0 use=1 tcp 6 586 ESTABLISHED src=68.46.9.24 dst=1.2.3.4 sport=64688 dport=6969 packets=6 bytes=490 src=10.0.0.2 dst=68.46.9.24 sport=6969 dport=64688 packets=8 bytes=944 [ASSURED] mark=40 secmark=0 use=1 udp 17 45 src=222.254.228.38 dst=1.2.3.4 sport=25438 dport=6969 packets=5 bytes=454 src=10.0.0.2 dst=222.254.228.38 sport=6969 dport=25438 packets=3 bytes=154 [ASSURED] mark=0 secmark=0 use=1 ( full file visible at http://pastebin.com/AZE6EtWm ) I've been playing around with this log for a little while and I can't see any patterns! Why is some port 6969 bittorrent traffic tagged mark=0 (not matched) by dd-wrt's QoS while others are tagged mark=40 (Bulk) .. any ideas?

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• DELL DRAC & Ubuntu VPN Connection

  - by Mikunos

  I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

  Read the article

• Missing startup screens and slow bootup/login after using WinClone to expand Bootcamp partition

  - by user26453

  I used WinClone to backup my Bootcamp partition, which was a Windows 7 Ultimate install, on my late 2006 Macbook Pro. I desired to expand the Bootcamp partition's size. It worked reasonably well with some hiccups along the way and some remaining issues. First issue I ran into was the Bootcamp Assistant utility - it would not recreate the partition. This was due to a lack of contiguous space that is required for the Bootcamp partition. As a result I wiped the whole drive and reinstalled Snow Leopard, did the minimum amount of system updates, and created and formated a new Bootcamp partition. WinClone restored the image without complaint and the image was automatically resized to the new partition's size. Second issue I ran into was after the first boot into Windows. The first thing I noticed was that instead of the newer "slick" startup screen (4 colors wisping around, a Windows 7 title), there was more of an old school style startup screen (a progress bar with block increments, yellow/greenish color, nothing else really). The initial bootup to a login screen was slow, perhaps as Windows dealt with the partition changes. After logging in, the screen goes blank and the computer seems to hang for a minute, before completing the login. After subsequent restarts, the slick screen is still missing, boot to login screen is normal, but the time from login to desktop active is still very slow. As a side note, this behavior of a long time from login to the desktop finally loaded I've previously only seen when the computer would try to hibernate and fail (battery is really bad). On the next startup, I would see this behavior, but not subsequently. So a potential cause: I imaged the partition after hibernating out of Windows. From reading some posts/guides on the subject, this was not recommended, and perhaps shouldn't even have worked? Could the partition be stuck in some weird mode as a result that makes the boot issues appear? I've attempted to disable hibernation and restart, trying to delete the .sys file that hibernation uses. Other fixes I'm thinking of attempting are booting a Win7 disc and repairing the install/partition. I can't shake the nagging feeling something isn't right as a result of the modified boot screens and the slow login process.

  Read the article

• Wireless traffic stops when downloading large files at high speed: packets lost (Linksys WRT120N router)

  - by Torious

  The problem Note: First I'd like to understand WHY this is happening. Ofcourse, a solution would be nice too. :) When downloading a large file over HTTP at high-speeds, my wireless traffic basically stops: I can't open webpages and the download itself pauses. It pauses pretty much immediately after starting it; sometimes at 800 KB, sometimes at a few MB. After some time, the download (and other traffic) resumes, but the problem keeps reoccurring during the same download. The problem does not occur when using a wired connection through the same router (Linskys WRT120N). Also note that the connection is not dropped when this happens. It's just that the traffic stops and I can't browse to web pages, etc. (SYN packets are sent but nothing is received, etc.) Inspection with Wireshark shows that the following happens: Server sends data packets which are acknowledged by client Server sends a packet, but SEQ indicates some packets were lost (6 packets in one occurrence). Server sends a few more packets and client acknowledges these using "selective acknowledgement" Server stops sending data for a while (since the lost packets were not acknowledged or the router stops forwarding them?) Eventually, server does a "retransmission" and traffic resumes as normal. This all seems normal behavior to me when packet loss occurs. It's the consistent packet loss throughout a large, high-speed download that puzzles me. What might cause this? My own idea is the following: My internet is pretty fast (100 mbps), so when starting a large-file download, the router buffers the incoming data (since wireless introduces some slight delay / lower speed, in part due to other networks), but the buffer overflows and the router drops packets to regulate traffic (and because it has no choice). But how could that happen? Doesn't the TCP window size limit the amount of data that can go unacknowledged? So how can the router's buffer overflow if there can only be like 64 KB waiting to be acknowledged? Note: I've disabled TCP window scaling and dynamic window size through netsh options, in an attempt to fix this, but it doesn't seem to matter. Also, Wireshark shows a pattern of the server sending 2 packets (of 1514 bytes) and the client sending an ACK, so does that rule out a possible buffer overflow? And a few more subsequent packets are received... I'm at a loss here. Thanks for any insights. Things that are (probably) NOT the cause / I have experimented with The browser Various TCP options in Windows 7 (netsh etc.) Router settings such as MTU, beacon interval, UPnP, ...

  Read the article

• Windows 2003 Storage Server Hanging on Large File Transfers

  - by user25272

  In one of our offices we have a Dell PowerVault 745N NAS device which acts as the main file server. Its running 32bit Windows 2003 Storage Server SP2 with 3GB RAM. The server holds around 60 users HOME folders, which are mapped via AD. The office clients are a mix of XP SP3, Vista and Windows 7. Occasionally the server will completely hang when transferring large files. When the hang happens the console becomes unresponsive with only the mouse active and blank wallpaper. Sometimes stopping the copy frees the server, sometimes not. The hanging can last around 20 minutes. During this time other servers also become unresponsive with blank wallpaper at the console. If you do manage to get onto another server the taskbar and run commands are unresponsive. This also transcends to the client computers sometimes with explorer crashing. I'm guessing this is due to the HOME folder mapping. Eventually the NAS server with free up and everything will be back to normal. The server is configured as follows: PERC 4/DC DATA 2 - 12 SCSI HDD - RAID5 SHADOWCOPY 2 SCSI HDD - RAID1 CERC SATA DATA 11 4 SATA HDD - RAID5 OS 4 SATA HDD - RAID5 All the drivers and firmware is up to date. I've been through all the diagnostics with Dell and the hardware has come up clean including full HDD tests on the arrays. The server has NOD32 installed as the AV, but the hanging happens when it is uninstalled. There are no errors in the event log when this happens and we don't have any errors logged on any of our ProCurve switches. DNS is fine on the domain and AD from what I can tell is running happily. There are no DFS or NFS shares setup either. All the shares are standard Windows. I've unchecked the allow the computer to turn off this device to save power box under Power Management on the NIC. "Set Link Speed and Duplex to Auto-negotiate 1000 " Increased Receive Descriptors buffer from 256 to 352 (reserves more CPU resource for handling data) I've run network traces using network monitor and have found the following: 417 8.078125 {SMB:192, NbtSS:25, TCP:24, IPv4:23} 192.168.2.244 192.168.5.35 SMB SMB:R; Nt Create Andx - NT Status: System - Error, Code = (52) STATUS_OBJECT_NAME_NOT_FOUND I've tried different cabling; NICs and switch ports all with the same result. Transferring files from other servers on the domain is fine. All I haven't done is run CHKDSK on the drives to look for any file system errors. On the Vista clients I have also run netsh interface tcp set global autotuning=disabled with no result. Could it be that the server has a faulty drive or that the I/O is too much for it to handle? Any ideas why would the hang cause issues with the other servers on the LAN? Many Thanks.

  Read the article

• Local Apache on Windows XP not finishing page requests

  - by asgeo1

  I have Apache 2.2.11 installed locally on my Windows XP (SP3) dev machine, which I setup about 3 months ago. I have just started having a strange problem in the last few week. Apache is serving some basic PHP applications like phpMyAdmin. When I make a page request, Apache appears to not finish serving all resources for that page. Firefox shows the "Transferring data from servername..." message, and the page never completes. The same problem happens in Internet Explorer too. I can sometimes tell which resource it is waiting on, because most of the page will render except for some image or similar resources. (Not sure why Firebug doesn't show this) It doesn't have the problem every page request - for page requests where most of the resources are cached in my browser, the page request will work with no problems. Or pages that are very light will work with no problems. However, if I "hard" refresh the page, I will have this problem (probably because it is requesting all page resources) Does anyone know what this could be? It is so strange that it has only just started happening - and I did not make any changes to my system (that I am aware of) I tried playing with the Apache ThreadsPerChild setting, but it did not seem to make a difference. UPDATE: I have been doing some more tests. I have been serving the most basic of pages, just a plain HTML file: <html> <body> <h1>testing</h1> </body> </html> If I request this page multiple times in a row, AND each request occurs immediately after the previous has completed, then 50% of the time the request will time out. However, if I put a 1-2 second gap between requests, then there is no problem. This correlates to what I have observed when the brower requests a real application page. When the browser has nothing cached, then all of the page resources are requested from the browser in a short amount of time - this appears to trigger the problem. UPDATE2: Nathan Long has helped me understand the issue a little better with the server-status page (see below). It is weird, it is like the server has a hickup sending data to the client. The client sits there waiting forever for data that never arrives. Closing the client process does not terminate the connection on the server - the server still has active threads for each previously attempted connection, but they just sit there - not sending any data and never terminating. (even though the client is now closed) Only a restart of the server seems to terminate them.

  Read the article

• Is DHCP lease expriring years from now okay?

  - by sharptooth

  I'm reviewing Azure web role logs and there's output from ipconfig /all IPv4 Address. . . . . . . . . . . : 10.61.145.37(Preferred) . Subnet Mask . . . . . . . . . . . : 255.255.254.0. Lease Obtained. . . . . . . . . . : Monday, September 24, 2012 12:26:00 PM. Lease Expires . . . . . . . . . . : Thursday, October 31, 2148 6:55:12 PM. you see, the lease expires in year 2148 but my VM will likely not run for more than one month - when I deploy the new version of my code I first deploy it to new VMs, then switch traffic, then release the new VMs. In general such usage pattern is normal - VMs typically live from several dozen minutes to several weeks on Azure. I suspect the lease that long will cause problems on the internal Azure network sooner or later. Is such long DHCP lease okay or is it likely a misconfiguration?

  Read the article

• Postfix to deliver mail to a virtual address mailbox

  - by Chloe

  Postfix version 2.6.6, Dovecot Version 2.0.9 I want to setup Postfix + Dovecot. Dovecot seems to be working. I can authenticate. However, the mailbox is empty! Nothing will get delivered! I followed many tutorials on Postfix + Dovecot but they seem to want to complicate things by using Dovecot LDA or MySQL. I just want it to be very simple and having Postfix deliver to the virtual mail boxes are fine. I don't need MySQL either. I already set up a custom password file that Dovecot uses for authentication and I can login to POP3 with SSL. I can see from the logs that Postfix is delivering to the system user accounts (the catch-all), instead of the virtual users that I set up in Dovecot. The SMTP + SSL authentication seems to work also. I can also see from the logs that Dovecot is checking the correct virtual mail folder. I just need to figure out how to get Postfix to deliver to the virtual mail boxes. I have the following which I believe are relevant. Let me know what other settings you need to see: alias_maps = hash:/etc/aliases mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain mydomain = xxx.com myhostname = mail.xxx.com mynetworks = 99.99.99.99, 99.99.99.99 myorigin = $mydomain relay_domains = $mydestination, xxx.com, domain2.net, domain3.com sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = reject_non_fqdn_sender reject_non_fqdn_recipient reject_unknown_recipient_domain permit_sasl_authenticated check_relay_domains smtpd_sasl_auth_enable = yes smtpd_sasl_path = private/auth smtpd_sasl_type = dovecot smtpd_sender_restrictions = check_sender_mx_access cidr:/etc/postfix/bogus_mx reject_invalid_hostname reject_unknown_sender_domain reject_non_fqdn_sender virtual_mailbox_base = /var/spool/vmail virtual_mailbox_domains = xxx.com, domain2.net, domain3.com virtual_minimum_uid = 444 Postfix master.cf: submission inet n - - - - smtpd -o smtpd_tls_security_level=encrypt -o smtpd_sasl_auth_enable=yes -o smtpd_sasl_type=dovecot -o smtpd_sasl_path=private/auth -o smtpd_sasl_security_options=noanonymous -o smtpd_sasl_local_domain=$myhostname -o smtpd_client_restrictions=permit_sasl_authenticated,reject -o smtpd_sender_login_maps=hash:/etc/postfix/virtual -o smtpd_sender_restrictions=reject_sender_login_mismatch -o smtpd_recipient_restrictions=reject_non_fqdn_recipient,reject_unknown_recipient_domain,permit_sasl_authenticated,reject Dovecot related: mail_location = maildir:~/Maildir passdb { args = /etc/dovecot/users.conf driver = passwd-file } service auth { unix_listener /var/spool/postfix/private/auth { mode = 0660 user = postfix } } The virtual mail user: vmail:x:444:99:virtual mail users:/var/spool/vmail:/sbin/nologin Here is the /var/log/maillog when I try to send something to myself: Oct 25 22:10:05 308321 postfix/smtpd[2200]: connect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:05 308321 postfix/smtpd[2200]: D224BD4753: client=user-999.cable.mindspring.com[99.99.99.99], sasl_method=LOGIN, [email protected] Oct 25 22:10:06 308321 postfix/cleanup[2207]: D224BD4753: message-id=<7DC3C163CFFC483AB6226F8D3D9969D2@dumbopc> Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: from=<[email protected]>, size=1385, nrcpt=1 (queue active) Oct 25 22:10:06 308321 postfix/smtpd[2200]: disconnect from user-999.cable.mindspring.com[99.99.99.99] Oct 25 22:10:06 308321 postfix/local[2208]: D224BD4753: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=1.1, delays=0.53/0.02/0/0.51, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 22:10:06 308321 postfix/qmgr[2168]: D224BD4753: removed

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Impact of the L3 cache on performance - worth a dual-processor system?

  - by Dan Nissenbaum

  I will be purchasing a new high-end system, and I would like to have a better sense of whether a dual-processor Xeon system (I am looking at the new, high-end Xeon E5-2687W) might, realistically, provide a noticeable performance improvement due to the doubling of the L3 cache (20 MB per CPU). (This is in addition to the occasional added advantage due to the doubling of cores and RAM.) My usage scenario is, roughly, that I have many background applications running at any time - 3 or 4 data compression/backup applications, a low-impact web server, one or two virtual machines at any given time (usually fairly idle), and perhaps 20 utility programs that utilize a noticeable (but small) portion of the CPU cores. In total, when I am not actively using the computer, about 25% of the total CPU power is utilized in my current i7-970 6-core (12 thread) system. When I am doing routine work, the CPU utilization often exceeds 50%, and occasionally hits 75%-80%. The Xeon E5-2687W is not only a second-generation i7 (so should improve performance for that reason), but also has 8 cores (16 threads), rather than 6 cores. For this reason, I expect to run into the 75% CPU range even less frequently. Nonetheless, the ability to double the cores and the RAM is a consideration. However, in the end, I believe this decision comes down to whether the doubling of the L3 cache will provide a noticeable improvement. There are many benchmarks, and a lot of discussion, regarding CPU power. However, I find very little discussion of L3 cache utilization, and how increases in the L3 cache (such as doubling it with dual processors) affect performance. For example: If there are only two processes running, but each benefits from a large L3 cache (such as might be the case for background processes that frequently scan the file system), perhaps the overall system performance might noticeably improve with dual CPU's - even if only a single core is active on each CPU - due to each process having double the effective L3 cache. I am hoping that someone has a sense of the benefits of increasing (or doubling) the L3 cache size. Note: the CPU I am considering (the Xeon E5-2687W) has 20 MB L3 cache, so a system with dual CPU's would have 40 MB L3 cache.

  Read the article

• Cannot connect to WEBrick on home network

  - by Chris Stewart

  I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

  Read the article

• Old CRT screen's high resolution doesn't work anymore on windows 7

  - by Mixxiphoid

  One year ago I decided to switch from Windows XP to Windows 7. I had a 17" CRT monitor with a screen resolution of 1600x1200 which worked fine on Windows XP. While installing Windows 7 everything went well until Windows 7 was going to install the video card its driver. Windows 7 puts the screen to its recommended resolution and my screen became black. I waited a few minutes to be sure the installation was finished. I turned off the computer by hand and restarted the computer on a resolution of 800x640. When windows 7 was done installing I went to screen resolutions and the resolution of 1600x1200 was on the top of the list with '(recommended)' next to it. I tried putting it on 1600x1200 but again my screen went black. I installed all windows 7 updates including the video card driver from the NVidia site (NOT from Windows 7). I tried about everything to make it work on 1600x1200 but with no succes. The highest resolution I got with the crt monitor was 1280x1024. I had a TFT screen which had 1280x1024 as max resolution and had better colors, so I used that one till today. My video card is 9600GT and my power supply is beyond sufficient. I even tried to install the driver I had on XP to see if it worked, but no results. I tried classic mode on windows 7, changed the dpi, the frequentie and the monitor settings, but nothing worked. I really like a vertical resolution of 1200, but it seems today I'm bound to all those standard monitors with a resolution of 1980x1024... Can anybody explain to me what the cause is that it worked on Windows XP but not on Windows 7? And maybe a solution to the problem (I actually gave up on getting it fixed...) Thanks a lot in advance. SOLUTION I downloaded the according monitor driver and installed it. Next I rebooted my computer on low resolution (800x640) and connected the CRT monitor. When Windows 7 booted successfully I went to computer management and 'update the driver' of my monitor. I manually selected 'Generic PnP monitor' and made that one active. I want to advanced settings at 'Screen resolution' and selected the mode '1600x1200 (32-bit) 80 Hertz (95 Hertz did not work). Now I had my resolution on 1600x1200. I repeated the earlier step to select the original monitor again instead of the Generic monitor. Quite a way to solve this problem, but it worked! Thanks a lot you all.

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Plesk Postfix Mail Server 9.5.4 very heavy load, 1000s of processes

  - by Eugene van der Merwe

  Our Plesk Linux Ubuntu 64-bit mail server has extremely high load and we don't know how to isolate it. The load was okay will two weeks ago but in the last two weeks it's seriously deteriorated. The mail server has been running for years and we have had sporadic performance issues. Normally we reduce the load by turning off all SPAM checks until the problem is sorted (which sometimes resolves itself). Currently we have turned of real time block lists, SPF checking and we have attempted to turn off SpamAssassin. No matter what we do the SpamAssassin check box stays ticked in the GUI. Out of desperation we have done /etc/init.d/psa-spamassassin stop. For years we haven't been able to do SpamAssassin because it kills the server. We would like to use it but performance is more important for now. We cannot turn off Greylisting. The moment we turn off Greylisting our help desk is inandated with calls. Out of desperation we investigated truncating the Greylisting database which is now 2.5 GB big but we abandoned this after noticing turning of Greylisting doesn't improve the performance at all. We have no anti-virus. It's just more load and Dr. Web never really worked that well for us. But we'll try that if it will make a difference. We have implemented Postfix Anvil. This seems to have made the situation worse so we disabled it. We’re not sure if this is the case. Our current mail server is configured to forward all SMTP to a relay server. We did so to reduce the load. This helped a lot because outgoing queues are generally empty. We are running in an Expand configuration. The mail server has about 12 000 accounts of which maybe half are active. We have read through this document: http://www.postfix.org/STRESS_README.html but there are too many settings and we don’t know which ones to choose. Please assist urgently. We need advice on how to fix this problem before all our clients abandon is. The only clue we have is that there are 100s of these processes: 30 13205 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13207 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue 30 13208 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13209 1 0 11:38 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10026 before-remote 30 13213 1 0 13:18 ? 00:00:00 /usr/lib/plesk-9.0/postfix-queue 127.0.0.1 10027 before-queue

  Read the article

• Kernel-mode Authentication: 401 errors when accessing site from remote machines

  - by CJM

  I have several Classic ASP sites that use Integrated Windows Authentication and Kerberos delegation. They work OK on the live servers (recently moved to a Server 2008/IIS7 servers), but do not work fully on my development PC or my development server. The IIS on both machines were configured through an IIS web deployment tool package which was exported from an old machine; the deployment didn't work perfectly, and I had to tinker a bit to get the sites working. When accessing the apps locally on either machine, they work fine; when accessing from another machine, the user is prompted by a username/password dialog, and regardless of what you enter, ultimately it results in a 401 (Unauthorised) error. I've tried comparing the configuration of these machines against similar live servers (that all work fine), and they seem generally comparable (given that none of the live servers are yet on IIS7.5 (Windows 7/Server 2008 R2). These applications run in a common application pool which uses a special domain user as it's identity - this user has similar permissions on the live and development machines. On IIS6 platforms, to enable kerberos delegation, I needed to set up some SPNs for this user, and they are still in place (even though I don't believe they are needed any longer for IIS7+ due to kernel-mode authentication), Furthermore, this account is enabled for Kerberos delegation in Active Directory, as is each machine I am dealing with. I'm considering the possibility that the deployment might have made changes/failed to make changes to the IIS configuration thus causing this problem. Perhaps a complete rebuild (minus another web deployment attempt) would solve the problem, but I'd rather fix (thus understand) the current problem. Any ideas so far? I've just had another attempt at fixing this issue, and I've made some progress, but I don't have a complete fix...yet. I've discovered that if I access the sites via IP address (than via NetBIOS name), I get the same dialog, except that it accepts my credentials and thus the application works - not quite a fix, but a useful step. More interestingly, I discovered that if I disable Kernel-mode authentication (in IIS Manager Website Authentication Advanced Settings), the applications work perfectly. My foggy understanding is that this is effectively working in the pre-IIS7 way. A reasonable short-term solution, but consider the following explicit advice from IIS on this issue: By default, IIS enables kernel-mode authentication, which may improve authentication performance and prevent authentication problems with application pools configured to use a custom identity. As a best practice, do not disable this setting if Kerberos authentication is used in your environment and the application pool is configured to use a custom identity. Clearly, this is not the way my applications should be working. So what is the issue?

  Read the article

• System Reserved partition no longer marked as System

  - by Mark

  I recently posted a question to Super User about accidentally marking my external HDD's partition as Active and how I could undo my accidental mistake. I followed the instructions provided and they worked fine. This involved some command line magic and from what I understand, I did not have to really do this, but I just wanted to get things back to how they were originally. After making the fix things went back to normal in disk management. After I restarted my computer though i had an issue: BOOTMGR is missing Press Ctrl+Alt+Del to restart Rugh roh! I brought my laptop to work so I could search for a solution on my work computer and I found a nice guide on fixing the issue. To summarize the instructions, I had to reboot with my Windows 7 install disc and click the Repair button. Once there I could then repair the start-up options. One of the commenters on the site claimed you need to do this twice, as the first time the "repair" doesn't actually fix it. I found this to be true as well. I tried to repair it and it did some work, then rebooted. I then got the same error again. I booted from the CD again and repaired the start-up options then after this second time Windows started to boot up. Before the restart I got a nice info window telling me that it did make repairs to the boot info (this was promising). I've been using Windows 7 for a few days now with no problem, but I just recently noticed that I now can see the System Reserved partition in Computer: (click for full size) I immediately went to disk management to see what was up. I noticed that my System Reserved partition is no longer marked as System and instead I believe the repair operation made my C: drive the system partition. I'm not fully aware of what the System partition really is but I briefly read that its a Windows 7 thing that gets created on install of Win7 that writes some BitLocker encryption stuff to a isolated partition as well as some boot files. (click for full size) How can I undo this and make the System Partition marked as System instead of my OS C: partition? How can I make it so that I don't see this partition in Computer (I believe fixing #1 will fix this) What are the implications of what the current state is and the fact that I can now browse into this new partition? Thanks in advance.

  Read the article

• Searching For a Desktop Security Software to harden Windows machines, anybody?

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So if anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• Add user in CentOS 5

  - by Ron

  I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

  Read the article

• Emails not being delivered

  - by Tomtiger11

  Comment pointed out that this may fix my problem, and it did: Why don't mails show up in the recipient's mailspool? I use Postfix with Dovecot, and when I send an email from my gmail to my server, it is received at the server, but not at my email client using POP3. I can verify it being received at the server using the mail command. This is my main.cf: queue_directory = /var/spool/postfix command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix mail_owner = postfix myhostname = tom4u.eu myorigin = $myhostname inet_interfaces = all inet_protocols = all unknown_local_recipient_reject_code = 550 relay_domains = $mydomain alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.6.6/samples readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES smtpd_tls_cert_file = /etc/postfix/certs/cert.pem milter_protocol = 2 milter_default_action = accept smtpd_milters = inet:localhost:8891 non_smtpd_milters = inet:localhost:8891 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $myhostname smtpd_recipient_restrictions = reject_non_fqdn_recipient,permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination,permit broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth If you could help me with this, I'd be most grateful, if you need any more information, please ask. var/log/maillog: May 30 22:44:25 tom4u postfix/smtpd[18626]: connect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/smtpd[18626]: 318F679B7F: client=mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/cleanup[18631]: 318F679B7F: message-id=<CAA_0zdxY-WUFGOC57K_yVn0G+5hN=8KSXuohJqMDB5Rm7bqu8w@mail.gmail.com> May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: mail-we0-f181.google.com [74.125.82.181] not internal May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: not authenticated May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: DKIM verification successful May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: s=20120113 d=gmail.com SSL May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: from=<[email protected]>, size=1720, nrcpt=1 (queue active) May 30 22:44:25 tom4u postfix/smtpd[18626]: disconnect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/local[18632]: 318F679B7F: to=<[email protected]>, relay=local, delay=0.17, delays=0.12/0.01/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: removed May 30 22:45:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18679 May 30 22:45:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0 May 30 22:46:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18725 May 30 22:46:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0

  Read the article

• GPU not powering on

  - by Lerp

  So I got home from work yesterday and went to turn my computer on as per usual to be greeted by this: The screens remained black, so I rebooted; I go as far as GRUB before my screens went black again. I rebooted again, they didn't turn on. I rebooted again, I got as far as the windows login screen. This time I unplugged it, opened it up and cleaned it but to no luck. The GPU was still being tempermental. I repeated the process of turning off and on several times until one time it work as normal. I happily played games for the rest of the night (5-6 hours?) thinking everything was jolly good now. Well I get home from work today and it is doing the SAME thing. Sometimes everything displays normally for a few seconds to minutes then the screens go black; then sometimes the screens don't come on at all. Summary and additional points Screens sometimes turn on before shortly turning off, sometimes they don't; I cannot seem to determine any pattern between when they do or do not turn off. The build has been working fine for about 8 months now so I know it's not hardware incompatibility. If I plug a monitor into the on board graphics I can use the PC normally (just in low graphics mode) I have two monitors and it's a case of they both turn on or not. So I think I can rule out the monitors being dead. I have tried replacing the GPU I have tried replacing the RAM I have tried flashing the CMOS I have tried cleaning the inside The GPU is a Radeon HD 7870 My questions Is my GPU dead? It's not very old and I would rather have a method of being certain it's the GPU before I fork out some money I can't really afford. I do not have a second PC here to test it in. If my GPU is dead why does it sometimes work and sometimes not? Update Okay, it was working again.. at least I thought it was. I left it running for 10-20minutes with the screens black. Turned it off and straight back on and it worked for all of 10minutes. I was then updating the post in joy thinking I could play some games for the rest of the night when BAM it went black again. So yeah, I don't know :C

  Read the article

• script to count the occurence of the particular string in the given time interval

  - by pruthvi

  We are trying to write a script "sendemail.sh" to count the number of occurrence of a particular string in a log file "SendEmail.log" within the given interval. We have a log file. In that we are searching for a pattern "ReqInputMsgLog" and need to count the number of times it occurred in the given period for eg: from "2014-08-19 11:30" to "2014-08-19 11:34". And our script look like this: #!/bin/sh enterdate=$1 echo $enterdate enddate=$2 enterdate1=`date +%s -d $enterdate +"%Y-%m-%d %H:%M"` echo $enterdate1 enddate1=`date +%s -d $enddate +"%Y-%m-%d %H:%M"` echo $enddate count=0 cat SendEmail.log | grep "ReqInputMsgLog" | awk -F "[" '{print $3}' | awk -F "," '{print $1}' > /con/scripts_server/file.txt for line in `cat /con/scripts_server/file.txt` do logdate=`echo $line | awk -F : '{print $1":"$2}'` if [[ $logdate < $enddate1 ]]; then count=`expr $count + 1` fi done echo $count But when we are trying to execute the script by the below command its not showing the proper count. ./sendemail.sh "2014-08-19 11:30" "2014-08-19 11:34" Log file is very big one. Small chunk has been posted here. INFO [SIBJMSRAThreadPool : 5] [2014-08-19 11:18:24,471] SendEmail - 8/19/14 11:18 AM,ECCF25B0-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,235] SendEmail - 8/19/14 11:18 AM,ECCEFDB2-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,241] SendEmail - xmlText: <?xml version="1.0" encoding="UTF-8"?> after awk command we will get a file "/con/scripts_server/file.txt" which looks similar like below: 2014-08-19 11:28:03 2014-08-19 11:28:06 2014-08-19 11:28:17 2014-08-19 11:28:53 2014-08-19 11:29:02 2014-08-19 11:29:47 2014-08-19 11:29:57 2014-08-19 11:30:07 2014-08-19 11:30:17 2014-08-19 11:30:19 2014-08-19 11:30:19 2014-08-19 11:30:22 2014-08-19 11:30:25 2014-08-19 11:30:25 2014-08-19 11:30:36 2014-08-19 11:30:51 2014-08-19 11:30:56 2014-08-19 11:30:59 2014-08-19 11:30:59 2014-08-19 11:31:08 2014-08-19 11:31:25 2014-08-19 11:32:19 2014-08-19 11:32:22 2014-08-19 11:32:27 2014-08-19 11:32:28 2014-08-19 11:32:41 2014-08-19 11:32:49 2014-08-19 11:32:59 2014-08-19 11:33:27 2014-08-19 11:33:41 2014-08-19 11:34:07 2014-08-19 11:34:14 2014-08-19 11:34:21 2014-08-19 11:34:25 2014-08-19 11:34:38 2014-08-19 11:34:50 2014-08-19 11:34:58

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

< Previous Page | 441 442 443 444 445 446 447 448 449 450 451 452  | Next Page >