Search Results

Search found 24081 results on 964 pages for 'microsoft office 2007'.

Page 448/964 | < Previous Page | 444 445 446 447 448 449 450 451 452 453 454 455  | Next Page >

• ssh works fine when using public interface, but slow when using private interface

  - by Kevin M

  My Linux(UbuntuEEE) to Linux(CentOS) ssh takes a long time to log in(~15 seconds) when using the private interface, but not when using the public one. I have a Linux box acting as my router. As such, it has multiple interfaces(75.xxx.xxx.xxx, 192.168.1.1). I can ssh in from the internal interface(192.168.1.65 to .1), but it will take a while. I can ssh into the public address, and it goes quickly(~1 second). I have another box that I can ssh into the inside interface from and it goes quickly. iptables is set to accept packets coming into the interface immediately. sshd's UseDNS is normally on; I get the same problem if I turn it off and restart sshd. I normally use public-key authentication; I have done a mv ~/.ssh/ ~/ssh/ and it will ask me for a password after going slowly. After logging in(using either interface), speed is quick. ssh client version(via ssh -v):OpenSSH_4.7p1 Debian-8ubuntu1.2, OpenSSL 0.9.8g 19 Oct 2007 ssh server version(via rpm -qv openssh_server):openssh-server-4.3p2-29.el5

  Read the article

• Can't find partition tab in disk utility osX ver. 10.6.8

  - by John W

  I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

  Read the article

• Disable internal display on Macbook Pro without closed lid mode?

  - by jslaker

  I have an early 2007 Macbook Pro running 10.5 that I've recently set up on a KVM with my primary desktop system. The problem I've run into is that I have a 20" 1680x1050 LCD, and OS X only provides options to mirror at the resolution of the built-in display or to span. Since the built-in display runs at 1440x900, this leads to running my LCD at non-native res and a fuzzy picture. There isn't any option that I can find to simply disable the built-in display entirely and run the external LCD at its native resolution. I am aware of closed lid mode, but the MBP was disassembled while in storage for about 6 months (took it apart to pull the HDD) and the cable to the touchpad, which controls the sleep sensor was damaged, meaning closed lid mode won't work. I've looked into replacing the cable, but the cheapest I've been able to find it is $75-100, and I'm trying not to invest any more money into this computer as it also has a completely dead battery and a few other minor problems. I've found the app SwitchResX which appears to allow you to do what I need, but it has a lot of functionality I don't need and a ~$20 registration charge attached to it. An odd set of circumstances, I'm aware, but I was hoping somebody might know of an OS hack that would let me just disable the internal display and be done with it. :)

  Read the article

• Are ZFS snapshots + S3 a viable backup system for several VMs and general fileserver storage?

  - by AllanA

  I've been tasked with setting up a backup system for my small office (around 12 people). Most of our production stuff is on the AWS cloud, so what I need to back up are some small office/development files (under 100G right now), plus our operational VMs and development, which round out to a bit under 1T. I just need something reliable, convenient, and straightforward. I'm comfortable with Linux, FreeBSD, and to some extent Solaris 10, so I'm leaning toward a full server rather than an appliance system ala Openfiler or FreeNAS. What I'm contemplating is a small fileserver for general storage and nightly backups of the virtual machines, followed up by an offsite backup to Amazon's S3 storage service. It'd be the usual incremental backups nightly and full backup weekly. My question is if using ZFS snapshots, both locally and dumped to S3 via 'zfs send [-i]', is a viable backup tool? Or should I stick to using Duplicity, or some other method entirely? ZFS snapshots on the internal fileserver/backup machine sound like a perfect way to provide quick and convenient data recovery, so I'm likely to go with that for local redundancy. (If you folks see scenarios where relying on ZFS snapshots would be worse than a more traditional archiving backup, feel free to convince me.) But are snapshots flexible enough to lean on for recovery from the loss of my backup server? Or am I better off with something more traditional? (feel free to recommend free or commercial backup solutions you favor.)

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• Virtual box host-only adapter configuration

  - by Xoundboy

  I have VirtualBox 4 running on Win 7 with a Centos 6 guest VM set up for hosting my dev server. When I'm connected to my home network the guest can be accessed via a static IP address that I configured (192.168.56.2), but not when I'm in the office. I'm guessing that the DHCP server in the office doesn't have a gateway configured for the 192.168.56.x IP range. I read something about the VB host-only adapter that should allow me to set this guest VM up in such a way that I don't need to be on any network to be able to access the guest from the host using a static IP. I've not been able to find out exactly how to configure this though. Can anyone give me an example configuration, thanks. UPDATE: Thanks for your responses. I've now set up a single virtual network adapter in VirtualBox and set it to host-only: C:\Users\Ben>vboxmanage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: d419ef62-3c46-4525-ad2d-be506c90459a Dhcp: Disabled IPAddress: 192.168.56.2 NetworkMask: 255.255.255.0 IPV6Address: fe80:0000:0000:0000:78e3:b200:5af3:2a57 IPV6NetworkMaskPrefixLength: 64 HardwareAddress: 08:00:27:00:94:e8 MediumType: Ethernet Status: Up VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter On the guest I've set up eth0 to use the same IP address as the host-only adapter (192.168.56.2) but when I try to log in using Putty I still get "Network Error : connection refused". VirtualBox DHCP servier is enabled but I can't ping the gateway (192.168.56.1) from either host nor guest. There's no firewall running on either OS. What next?

  Read the article

• Is it possible to record a screen-video from a VNC server?

  - by nikie

  I have a computer that's running VNC server. I would like to record a video of what's going on on this computer, if possible without installing additional software on that computer. Is there a program that can connect to the VNC server port and instead of displaying the screen save it to an (e.g. AVI) video file? Background: One of our customers sometimes has problems with the software he bought from us when he's performing a complex procedure. To help him, we offered that someone (a service technician or programmer) watches what he's doing during that procedure to find out if he's doing something wrong or if there's a bug in the software. Currently, this is done live via VNC. That has a few disadvantages: The service technician has to be in the office at the time. As the customers are in different time zones, that can be in the middle of the night. If the service technician forgets something or doesn't notice something, it's lost. There's no way to see what happened again. Only a single computer can be watched by one service technician at a time. I know I could install normal screen-grab software on the computer, but we're talking about an embedded system with limited RAM, CPU, HDD space, so installing something new is not an easy decision. And VNC is already there. I could of course open a VNC client on some office PC and capture that PC's screen, but I can only record one remote computer that way. I often have to watch up to 8 screens in parallel. (And I don't think that screen-grabbing VNC would improve image quality, either.)

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• sharing a USB printer in SOHO environment [migrated]

  - by Registered User

  Here is a situation I am facing, there is USB printer which works only on a Windows XP machine, there are other devices in LAN it is a Small Office Home Office environment. How can this USB printer attached to Windows XP machine be shared so that other laptops or users in Network who have Windows 7 or Linux on their laptops can use this printer. The printer model number is Canon Laser Shot LBP-1210 http://www.canon-europe.com/For_Home/Product_Finder/Printers/Laser/LaserShot_LBP1210/index.asp a print server is not available to me I need to make it work in this situation only.What can I do? the clients are unable to connect to this.It is not a network or TCP/IP printer If a from Windows 7 machine some one wants to use this printer so that he can take a print he gets an error while adding the printer to his machine which is a Windows 7 machine (where as the printer is USB printer on Windows XP machine) Start--->Devices and Printers---> Add Printer---> Find Printer by name or IP address--->Selected a shared printer by name-->\\PC-Name-printer3 and select browse it gives a message Windows can not find a driver for Canon LASER SHOT LBP-1210 on the network what does this mean do I need to install some kind of software at client machine or on the machine where printer is present?

  Read the article

• 64-bit Windows 7 gets stuck on logo screen on bootup

  - by Richard B

  I've had a PC running Windows 7 in my office which I'm not using at the moment (cause I'm working elsewhere as a consultant atm), I'm only accessing the PC using Team Viewer (http://www.teamviewer.com/) which means the PC has been running for quite some time now. I've restarted it maybe twice a week though. A few days ago I couldn't access it using Team Viewer and when I got to the office the screen was black with only the mouse pointer showing. The PC has four hard disks, three of them (all 1Tb) is using RAID 5. This is what I've done so far: I reboot and everything seems to load correctly. I get to a screen that gives me two choices - boot Windows normally or perform a startup repair. Choosing to boot Windows only gets me to the Windows 7 logo screen which only animates over and over again. Choosing to repair gets me to the repair screen that "checks for problems" and then it gets stuck on the "Attempting repairs..."-screen (I let it run for about 24 hours before giving up). What is the next step to take? I don't have any backups and no system restore points saved. I can access files and folders through a terminal window using a Windows 7 DVD so I guess nothing is lost yet... Please help me, thanks!

  Read the article

• Can I configure Thunderbird 3 to refresh the folder list for an Exchange IMAP account?

  - by Howiecamp

  Background: When used as an IMAP client against Gmail, Thunderbird 3 (may be the case in v2 also, not sure) will refresh it's list of folders (the folders correspond to Gmail labels) when you do "Download/Sync Now..." or restart the Thunderbird client. Any new folders (labels) created in Gmail will sync to the client and any folders moved/changed/deleted folders in Gmail will move/change/delete on the client as well. (Note: Thunderbird has the concept of "subscribing" to IMAP folders (assumingly allowing you to determine which folders you want, rather than bringing all of them down and dragging loads of data across the wire). When used against Gmail, Thunderbird appears to automatically subscribe to all folders (including when folders are newly created in Gmail), so this might be why the refresh is happening properly.) This behavior is what I want with Exchange. When using Thunderbird with Exchange (2007), the folder list doesn't refresh when folders are added/changed/deleted on the server and/or from a different mail client. When I look at the subscription options, some are checked and some are not (not sure why Thunderbird picked some and not others). And when I add new folders on the server and/or from another client, they never even appear in Thunderbird's list of folders, preventing me from subscribing to them.

  Read the article

• Permissions error when creating desktop shortcut

  - by Ryan M.

  Hey guys, I have a user that's got a weird permissions problem on Windows 7. He's trying to create a shortcut for Outlook on his desktop(he doesn't want it in his start menu or his taskbar...). If we right click the outlook.exe and do Send to Desktop, it works just fine. If we do a search for "outlook" in the search bar, and then try and drag and drop the outlook icon to the desktop, we get the error message "You need Permission to perform this action. You require permission from SYSTEM to make changes to this file: Microsoft Office Outlook 2007". Dragging and dropping other exe's onto the desktop work just fine. They create shortcuts without any problems. But if I try to do ANY of the Office programs (Word, Excel, Outlook, etc..) I get this permission error. Any ideas? He's using an A.D. account and he's in the local administrators group. He's an executive so he's not accepting "this isn't a real problem because I found another way to make a shortcut" as an answer. Any help is appreciated.

  Read the article

• 2 Computers, same network, different outgoing speeds when uploading to internet?

  - by user117339

  I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

  Read the article

• running a laptop continuously

  - by intuited

  I have an experienced laptop — a Dell Latitude D400, with a Pentium M CPU — that I'd like to run as an always-on server. This model was launched in 2004; I got mine second-hand in about 2007. I've heard that continuous operation is generally not a good idea with consumer hardware, but am lacking in specific knowledge about related problems, and have little idea of how much such usage patterns would reduce the lifespan of the machine. I'm mostly concerned with the unit's core components; parts such as the hard drive which are readily replaceable are, well, readily replaceable. What sorts of things can I do to increase the lifespan of this machine under such circumstances? For example, I'm guessing that it would be wise to limit the CPU frequency or take other steps to keep the internal temperature low. However, I'm not sure where the point of diminishing returns would lie with such an approach — 50°C? 40°C? Would it be useful to suspend the machine periodically, for perhaps an hour each day, or a few hours each week?

  Read the article

• troubleshooting postifx -> exchange connection issues

  - by Systemspoet

  I have three linux-based mail routers that run postfix and relay mail to our on-premise exchange server as well as to outlook.com, splitting the mail based on ldap atttributes. What I've observed sporadically since upgrading this spring from Exchange 2007 to 2010 is that all three of the mail relays will, for about 20 minutes, fail to connect to exchange. Postfix logs it as "lost connection with exchange.contosso.edu" ; this problem almost always occurs to all three mail relays at the same time, and lasts for slightly under 20 minutes. If I can catch it while it's occuring, and I manually do "telnet exchange.contosso.edu 25" from one mail relay and force a message through (helo, mail from, rcpt to, data, etc), then it clears that relay up. The exchange "server" is actually two machines with the HT role on them, load balanced via windows NLB. I've worked pretty hard to figure out what's happening from the postfix side and I can't see any evidence of any misbehavior. My question is, how do I attack the problem from the exchange side? Is there a connection log, or a debug setting, or something I can do to log all of the inbound connections and tell me what's causing exchange to drop them?

  Read the article

• How should an experienced Windows SysAdmin learn Linux? [closed]

  - by Systemspoet

  I have a new hire starting in a few weeks who is an experienced Windows SysAdmin. I think he's fairly senior on the Windows side, with a pretty deep AD understanding and experience with Exchange 2007, 2010, and exchange migrations. He's done a little PowerShell but I suspect more of the "run this command to do this" variety then "write a script to do this" sort. However, we are a mixed shop and (he knows this) I expect him to become a reasonably competent Linux SysAdmin over time. I'm looking for good starting points to bring him along. I have over ten years of Linux/UNIX experience, so it all sort of seems intuitive to me, but I've been thinking about the toolkit you actually need to be productive in the Linux CLI world. Just to be able to use the machines at all, off the top of my head... vi Basic CLI stuff -- move around, rename files, copy files, tar, gzip, changing passwords, finding relevant manpages, keep track of where you are, find things in your history, etc, etc. More advanced things that I take for granted but are actually pretty hard -- doing things with 'find', extracting relevant text via 'awk' and/or 'cut', knowing when to use 'grep' and when to use 'grep -e' or 'egrep'. Distribution specific stuff... compiling software, rpm, yum, apt-get, you name it. This all seems pretty basic to me, but when I think back to 1995 when I was first learning my way, some of those things took me years to master. So my question is -- where should I send him to pick up those skills? I'm not just thinking of classes, but rather also websites and books? Where do you all suggest as a starting point for picking up Linux skills?

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

• Create DFS replica from a NAS drive

  - by Mark

  We have two offices, at two different locations. In one we have a NAS, with some shares. We also have a Domain Controller using Windows 2003 R2. We have setup a second Domain Controller using Windows 2003 R2 to put that in the second office. What we would also like is to replicate the NAS drive onto the second Domain Controller so in the second office they have a local copy, and that their changes are replicated back to the NAS. Is there a way to setup DFS replication to do this? Or will it only work with local folders on each Server? Update 1 Sept Base on the answer below, I think I need to add some clarification. The real issue is that the NAS which hosts the shared folder that we want to replicate is external to both servers. And we have a particular share mapped to say S: . In the replication setup it doesnt seem to accept network shares external to the server to be candidates for replication. I can understand why, I just need confirmation that DFSR will only work with block devices that are local on at least one server. Is this the case?

  Read the article

• Sharepoint web part fails intermittently

  - by pringly

  I have a MOSS 2007 environment, 2 web servers and a DB server, load balanced between the two web servers. I deployed a web part recently, which worked fine for a while, but failed on web server 2 after a day. When it fails, it gets the error message: 'A Web Part or Web Form Control on this Page cannot be displayed or imported. The type could not be found or it is not registered as safe’ Once it has failed, it will stay that way until an IIS reset is done. The other web server never fails, I tried to force the second web server to fail to recreate the issue and have been unable to do it. I tried placing it under heavy http traffic and it handled it fine. Put it back in the pool and it failed again after about 7 hours. So, if i remove the .dll for the webpart from the affected web server, the webpart doesnt stop working. Is this normal behavior? I checked the bin directory for the site and the global assembly and it there is no other copy of the .dll anywhere else on the server. Also, when checking the web part gallery, if the web part has failed it will appear in the gallery, but by trying to add a new webpart, the .dll wont be listed. I have no idea how to continue troubleshooting from here or even fix it, any ideas?

  Read the article

• MacMini transmit rate stuck at 11, every other device can connect at full 54Mbit/s?

  - by chum of chance

  I have a MacMini circa 2007 that's getting very low transmit rates via wifi, 8-11. I have other devices that are getting full 54, including a MacBook Air. With everything else off, the MacMini doesn't want to seem to go any faster. Since it has been previously connected to ethernet its entire life, I was wondering if there were some settings I can change to speed up the connection. Option-clicking the network icon gives this read out: PHY Mode: 802.11g Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -73 Transmit Rate: 11 My new MacBook Air has the following readout: PHY Mode: 802.11n Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -66 Transmit Rate: 79 Both have full bars and the wireless router is in the same room to eliminate any obstructions from the equation. Could the MacMini be connecting at an older protocol, like 802.11b and be reporting erroneously that it is connected at 802.11g? This would explain why I haven't seen a transmit rate above 11. Any further trouble shooting I can try before buying a new USB 802.11n device? The WiFi router is a DLink DIR-615. I can see other devices, and none, even the other g connected devices, are getting below 30-40 MBit/s. What's going on here?

  Read the article

• Variable host IP address in iptables rule

  - by DrakeES

  I am running CentOS 6.4 with OpenVZ on my laptop. In order to provide Internet access for the VEs I have to apply the following rule on the laptop: iptables -t nat -A POSTROUTING -j SNAT --to-source <LAPTOP_IP> It works fine. However, I have to work in different places - office, home, partner's office etc. The IP of my laptop is different in those places, so have to alter the rule above each time I change place. I have created a workaround which basically determines the IP and applies the rule: #!/bin/bash IP=$(ifconfig | awk -F':' '/inet addr/&&!/127.0.0.1/{split($2,_," ");print _[1]}') iptables -t nat -A POSTROUTING -j SNAT --to-source $IP The workaround above works. I only still have to execute it manually. Perhaps I could make it a hook executing whenever my laptop obtains an IP address from DHCP - how can I do that? Also, I am just wondering if there is an elegant way of getting it done in the first place - iptables? Maybe there is a syntax allowing to specify "current hardware ip addres" in the rule?

  Read the article

• Printer spools but doesn't print

  - by DKNUCKLES

  I am having a bizarre issue with an end user who is unable to print to a USB attached printer. The environment is as Windows 7 machine with a Canon Pixma iP90 printer. The driver is installed (and has been re-installed several times), but whenever a print job is sent the printer spools but no printing ever occurs. The following is some relevant information I can confirm that the printer is spooling as the spool folder fills up, and the job "releases" and the spool folder empties I have turned off print spooling with no luck None of the features from the Canon utilities (ie Turn Printer Off) features work Computer recognizes the printer as being installed. When the cable is unplugged the printer icon grey's out in Devices and Printers Printer and cable are confirmed working as they work with other PC's in the office I have deleted the USB Root Hub devices and rebooted the machine with no luck No error messages are displayed or logged in the event viewer. The Canon diagnostics utility doesn't detect any problem and states the printer is functioning properly Printer is not shared User is able to print to other shared printers in the office Any help with this issue would be greatly appreciated.

  Read the article

• Convert Public Folder to Shared Mailbox

  - by Lilienthal

  Due to a change in company policy, all existing Public Folders (PF) have to be phased out in favour of shared mailboxes. Unfortunately, they don't seem to have any procedures or guidelines for this migration and I can't find much online either. I've already migrated one of our public folders so far as a sort of test case. Because we still use Exchange 2003, we can't create real shared mailboxes as we would in 2007 or 2010 (With New-Mailbox -Shared ... in the Exchange Shell). Instead, I simply created a new account on the AD and assigned it a mailbox. I then set the PF's permissions to read-only to keep it in a consistent state and copied the entire folder to a local PST in Outlook 2010, from which the folder was in turn copied to the new mailbox. Permissions and Folder Visible were set for all users and the migration was successful. While this works, the whole procedure feels very hackish to me and not at all efficient. I'd welcome some input on automating or at least streamlining the process. Additionally, we are unsure of what to do with our mail-enabled Public Folders. Several of these are nested under other PFs, some of which are also mail-enabled. Preserving folder structure is a key requirement and this seems impossible at first glance. I've considered creating dummy accounts for all the email addresses from our mail-enabled PFs and then setting up automated rules to forward messages to a subfolder of the new shared mailboxes, but I am not familiar enough with Exchange to know if this is even possible. Further points of concern are the Calendars and Contact lists in our public folders. I suppose I'll be forced to create new mailboxes for every one of these we have as well, then set up share permissions for their Calendar and Contact items, but would be happy to be proven wrong.

  Read the article

• "No such file or directory"?

  - by user1509541

  Ok, so I have a VDS laying around, and I thought I would turn it into a TF2 game server. When I connect to my server through PuTTY, and use wget to download the package "hldsupdatetool.bin" from Steampowered.com. I go to run it and it says "No such file or directory found". When I use "ls" to see what files are in directory, it lists "hldsupdatetool.bin" as being in the directory. So, why is it saying it's not there? This has been a headache for the past 2 days. It's returning: root@10004:~# wget http://www.steampowered.com/download/hldsupdatetool.bin --2012-07-08 06:04:49-- http://www.steampowered.com/download/hldsupdatetool.bin Resolving www.steampowered.com... 208.64.202.68 Connecting to www.steampowered.com|208.64.202.68|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 3513408 (3.4M) [application/octet-stream] Saving to: “hldsupdatetool.bin.3” 100%[======================================>] 3,513,408 2.45M/s in 1.4s 2012-07-08 06:04:51 (2.45 MB/s) - “hldsupdatetool.bin.3” saved [3513408/3513408] root@10004:~# chmod +x hldsupdatetool.bin.3 root@10004:~# ./hldsupdatetool.bin.3 -bash: ./hldsupdatetool.bin.3: No such file or directory root@10004:~# More: root@10004:~# ls ffmpeg-packages hldsupdatetool.bin.1 hldsupdatetool.bin.3 hldsupdatetool.bin hldsupdatetool.bin.2 setup.sh root@10004:~# ls -la total 13828 drwx------ 4 root root 4096 Jul 8 06:04 . drwxr-xr-x 21 root root 4096 Jul 8 05:57 .. -rw------- 1 root root 8799 Jul 8 06:26 .bash_history -rw-r--r-- 1 root root 570 Jan 31 2010 .bashrc -rw-r--r-- 1 root root 4 Jul 2 19:39 .custombuild drwxr-xr-x 2 root root 4096 Jul 4 18:49 ffmpeg-packages ---x--xrwx 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.1 -rw-r--r-- 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.2 -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.3 -rw-r--r-- 1 root root 140 Nov 19 2007 .profile -rw------- 1 root root 1024 Jul 2 19:49 .rnd -rwxr-xr-x 1 root root 38866 May 23 22:02 setup.sh drwxr-xr-x 2 root root 4096 Jul 2 19:44 .ssh root@10004:~#

  Read the article

• setting up vpn server

  - by Lock

  I need help in visualising how to setup our VPN box when we move to our new network with Telstra. We have a safe@office 500P, which has a public IP and a private IP of 192.168.19.2. It is physically connected to our router, which has 4 different interfaces, one being 192.168.19.1. On the VPN box, we have a static route to forward everything to 192.168.19.1 which is the router, and from there it works out where to go. Now, we are moving to a Telstra WAN and things are setup a little differently. Our head office router has only 3 interfaces- 1 is for the link to the switch that has the fibre connection (so our route to the internet and other branches), 1 is for our 10.10.20.x network and one is for the local branch network. I really have no idea how to set this up as with the new setup, we will not have a port for it to plug into on the router. Could I just plug it into the 10.10.20.x network? Would I have to give it a public IP or can we just forward through the ports that it would use? Another suggestion was to VLAN our switch into two networks- one for the 10.10.20.x network and one for the network the VPN currently sits on (192.168.19.x), and setup the router to trunk between the port and the switch. Not sure how to do this. Sorry VPN's are definitely not my strong suit. Any advice appreciated!

  Read the article

< Previous Page | 444 445 446 447 448 449 450 451 452 453 454 455  | Next Page >