Search Results

Search found 1134 results on 46 pages for 'cisco'.

Page 45/46 | < Previous Page | 41 42 43 44 45 46  | Next Page >

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

  - by zhallett

  I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

  Read the article

• RFC 1918 address on open internet?

  - by longneck

  In trying to diagnose a failover problem with my Cisco ASA 5520 firewalls, I ran a traceroute to www.btfl.com and, much to my surprise, some of the hops came back as RFC 1918 addresses. Just to be clear, this host is not behind my firewall and there is no VPN involved. I have to connect across the open internet to get there. How/why is this possible? asa# traceroute www.btfl.com Tracing the route to 157.56.176.94 1 <redacted> 2 <redacted> 3 <redacted> 4 <redacted> 5 nap-edge-04.inet.qwest.net (67.14.29.170) 0 msec 10 msec 10 msec 6 65.122.166.30 0 msec 0 msec 10 msec 7 207.46.34.23 10 msec 0 msec 10 msec 8 * * * 9 207.46.37.235 30 msec 30 msec 50 msec 10 10.22.112.221 30 msec 10.22.112.219 30 msec 10.22.112.223 30 msec 11 10.175.9.193 30 msec 30 msec 10.175.9.67 30 msec 12 100.94.68.79 40 msec 100.94.70.79 30 msec 100.94.71.73 30 msec 13 100.94.80.39 30 msec 100.94.80.205 40 msec 100.94.80.137 40 msec 14 10.215.80.2 30 msec 10.215.68.16 30 msec 10.175.244.2 30 msec 15 * * * 16 * * * 17 * * * and it does the same thing from my FiOS connection at home: C:\>tracert www.btfl.com Tracing route to www.btfl.com [157.56.176.94] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms myrouter.home [192.168.1.1] 2 8 ms 7 ms 8 ms <redacted> 3 10 ms 13 ms 11 ms <redacted> 4 12 ms 10 ms 10 ms ae2-0.TPA01-BB-RTR2.verizon-gni.net [130.81.199.82] 5 16 ms 16 ms 15 ms 0.ae4.XL2.MIA19.ALTER.NET [152.63.8.117] 6 14 ms 16 ms 16 ms 0.xe-11-0-0.GW1.MIA19.ALTER.NET [152.63.85.94] 7 19 ms 16 ms 16 ms microsoft-gw.customer.alter.net [63.65.188.170] 8 27 ms 33 ms * ge-5-3-0-0.ash-64cb-1a.ntwk.msn.net [207.46.46.177] 9 * * * Request timed out. 10 44 ms 43 ms 43 ms 207.46.37.235 11 42 ms 41 ms 40 ms 10.22.112.225 12 42 ms 43 ms 43 ms 10.175.9.1 13 42 ms 41 ms 42 ms 100.94.68.79 14 40 ms 40 ms 41 ms 100.94.80.193 15 * * * Request timed out.

  Read the article

• A dusty server room

  - by pauska

  Here's the story.. The owners of the building we lease office space from decided to do a renovation of the exterior. This involved in some pretty heavy work at the level where our server room is, including exchanging windows wich are fit inside a concrete wall. My red alert went off when I heard that they were going to do the same thing with our server room (yes, our server room has a window. We're a small shop with 3 racks. The window is secured with steel bars.) I explicity told the contractor that they need to put up a temporarily wall between our racks and the original wall - and to make sure that the temporary wall is 100 % air and water-tight. They promised to do so. The temporary wall has a small door in it, so that workers can go in/out through the day (through our server room, wich was the only option....). On several occasions I could find the small door half-way shut while working evenings/nights. I locked the door, and thought that they would hopefully get the point soon and keep the door shut. I even gave a electrician a mouthful when I saw that he didn't close the door properly. By this point - I bet that most of you get a picture of what happened. Yes, they probably left the door open while drilling in the concrete. I present you our 4 weeks old EMC VNX: I'll even put in a little bonus, here is the APC UPS one rack further away from the temporary wall. See the nice little landing strip from my finger? What should I do? The only thing that comes to mind is to either call all our suppliers (EMC, HP, Dell, Cisco) and get them to send technicians to check out all the gear in the server room, or get some kind of certified 3rd-party consulant to check all of it. Would you run production systems on this gear? How long? Edit: I should also note that our aircondition isn't exactly enterprise-grade, given the nature of our small room. It's just a single inverter, wich have failed one time before I started working here (failed inverters usually leads to water dripping out).

  Read the article

• pix 501, static route to d-link router (different subnet)

  - by ra170

  I have pix 501 cisco firewall with internal ip 192.168.10.1. I have connected d-link router (dir-655) to pix 501. The d-link router has internal ip 192.168.0.1 The picture would like something like that: |pix 501| has 192.168.10.1 ip |DIR-655| has 192.168.0.1 ip 1. |cable modem|----|pix 501|-------|DIR-655|-----PC 2. PC--------|pix 501|---------|DIR-655| | | |cable modem| When I'm on the wireless network (dir-655) with assigned ip of 192.168.0.x I can cross the subnet and connect to my firewall 192.168.10.1. (pic. 1) The problem is that if I'm on the 192.168.10.x network I can't connect to anything over at 192.168.0.x network. (pic.2) I've tried entering a static route like this: `route inside 192.168.0.0 255.255.255.0 192.168.10.1 1` I also tried assigning static ip to wan interface on DIR-655 to 192.168.10.30 and then tried this: route inside 192.168.0.0 255.255.255.0 192.168.10.30 1 But still, can't connect to 192.168.0.1 or anything on that subnet. Is there a way to setup a static route? Would adding a separate router between PIX 501 and DIR-655 help? I would think that static route like this should take care of it, but it doesn't. This is my route config and nat: (config)# sh route outside 0.0.0.0 0.0.0.0 (outside_IP) 1 DHCP static outside (outside_IP) 255.255.248.0 (outside_IP) 1 CONNECT static inside 192.168.0.0 255.255.255.0 192.168.10.1 1 OTHER static inside 192.168.10.0 255.255.255.0 192.168.10.1 1 CONNECT static or (route inside 192.168.0.0 255.255.255.0 192.168.10.30 1) (config)# sh nat nat (inside) 1 192.168.1.0 255.255.255.0 0 0 nat (inside) 1 192.168.10.0 255.255.255.0 0 0 nat (inside) 1 0.0.0.0 0.0.0.0 0 0 I ended up turning DIR-655 into an Access Point (turning off DHCP and pluging cable from PIX lan interface into one of the LAN interfaces on DIR-655, and leaving WAN port empty), that works as far as DIR-655 being on the same subnet now, and I can access every machine. However the question is, why can't I simply route between those two? would router between these two help? One of the reasons is, that the PIX 501 has only 10 licences, so now I'm using almost all of them. (I have few computers, iphones, ps3, print server, etc.) I would really appreciate some help! Thanks.

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• IT merger - self-sufficient site with domain controller VS thin clients outpost with access to termi

  - by imagodei

  SITUATION: A larger company acquires a smaller one. IT infrastructure has to be merged. There are no immediate plans to change the current size or role of the smaller company - the offices and production remain. It has a Win 2003 SBS domain server, Win 2000 file server, linux server for SVN and internal Wikipedia, 2 or 3 production machines, LTO backup solution. The servers are approx. 5 years old. Cisco network equippment (switches, wireless, ASA). Mail solution is a hosted Exchange. There are approx. 35 desktops and laptops in the company. IT infrastructure unification: There are 2 IT merging proposals. 1.) Replacing old servers, installing Win Server 2008 domain controller, and setting up either subdomain or domain trust to a larger company. File server and other servers remain local and synchronization should be set up to a centralized location in larger company. Similary with the backup - it remains local and if needed it should be replicated to a centralized location. Licensing is managed by smaller company. 2.) All servers are moved to a centralized location in larger company. As many desktop machines as possible are replaced by thin clients. The actual machines are virtualized and hosted by Terminal server at the same central location. Citrix solutions will be used. Only router and site-2-site VPN connection remain at the smaller company. Backup internet line to insure near 100% availability is needed. Licensing is mainly managed by larger company. Only specialized software for PCs that will not be virtualized is managed by smaller company. I'd like to ask you to discuss both solutions a bit. In your opinion, which is better from the operational point of view? Which is more reliable, cheaper in the long run? Easier to manage from the system administrator's point of view? Easier on the budget and easier to maintain from IT department's point of view? Does anybody have any experience with the second option and how does it perform in production environment? Pros and cons of both? Your input will be of great significance to me. Thank you very much!

  Read the article

• What router hardware or software should be used when multiple public IPs are routed into the same LAN?

  - by lcbrevard

  I am looking for recommendations to replace a set of consumer grade (Linksys, Netgear, Belkin) routers with something that can handle more traffic while routing more than one static public IP into the same LAN address space. We have a block of static public IPs, 5 usable, with Comcast Business. Currently four of them are in use for: General office access Web server Mail and DNS servers Download and backup web server for separate business All systems (a mixture of physical and virtual) are in the same LAN address space (10.x.y.0/24) to enable easy access between them inside the office. There are 30 or more systems in use depending on which virtual machines are currently active. We have a mixture of Windows, Linux, FreeBSD, and Solaris. Currently a separate consumer grade router is used for each of the four static addresses, with its WAN address set to the specific static address and a different gateway address for each: uses 10.x.y.1 - various ports are forwarded to various LAN IPs on systems with gateway 10.x.y.1 uses 10.x.y.254 - port 80 is forwarded to a server with gateway 10.x.y.254 uses 10.x.y.253 - ports for mail and dns are forwarded to a server with gateway 10.x.y.253 uses 10.x.y.252 - ports as needed are forwarded to server with gateway 10.x.y.252 Only router 1. is allowed to serve DHCP and address reservation based on the MAC is used for most of the internal "server" IP addresses so they are at fixed values. [Some are set static due to limitations in the address reservation capabilities of router 1.] And, yes, this really does work! But... I am looking for: better DHCP with more capable address reservation higher capacity so I don't have to periodically power cycle the routers One obvious improvement would be to have a real DHCP server and not use a consumer grade router for that purpose. I am torn between buying a "professional" router such as Cisco or Juniper or Sonic Wall verus learning to configure some spare hardware to perform this function. The price goes up extremely rapidly with capabilities for commercial routers! Worse, some routers require licensing based on the number of clients - a disaster in our environment with so many virtual machines. Sorry for such a long posting but I am getting tired of having to power cycle routers and deal with shifting IP addresses afterwards!

  Read the article

• Wifi network stopped being visible (and usable) (Linksys wag320n)

  - by s427

  Basically, my wifi network simply stopped working for no apparent reason. It doesn't appear in the list of the available networks anymore. I can see all my neighbors' networks, but not mine. It's as if it doesn't exist anymore. The internet connection (non-wifi), which goes through the same modem/router, is fine though. I already had a similar problem about one year ago (see here: Wifi network SSID not visible ), just after buying this very modem. I finally got it to work after performing two factory resets and getting rid of the Cisco "Magic" software; but this time it's not working. I use a linksys router-modem (WAG320N) which is directly connected (via network cable) to my desktop computer (Windows 7). I have (mainly) two devices that use the wifi network: my phone (Samsung Galaxy Nexus) and an Asus tablet (TF201, aka Transformer Prime). I also resurrected an old laptop computer (Dell, running Windows XP) to test that, and it doesn't see anything either (apart from the 20 other wifi networks, of course ^^). This wifi network was working just fine and has been for about a year. I haven't touched the modem settings so I have no idea what's causing the problem. I tried: making my phone "forget" about my network, hoping it would see it again after that: no luck. re-entering the network informations (SSID/password) manually on my phone: still no luck (says it's not in range) exporting the modem configuration, resetting the modem (factory reset, via modem admin), restarting it, importing the configuration: nope. factory reset, turning it off for 15 minutes, restarting, re-factory reset, and entering the configuration manually: still nothing. Has anybody experienced something similar before? Have you any suggestion to fix that? Thanks in advance. PS: to clear things up, here are the settings of my modem regarding wifi: Basic wireless settings: Configuration: manual Radio Band: 2.4GHz Wireless Network Mode: B/G/N-Mixed SSID: s427 Channel Bandwidth: Wide - 40 MHz Channel Wide Channel: 9 - 2.452GHz Standard Channel: 11 - 2.462GHz SSID Broadcast: Enable Advanced Wireless Settings AP Isolation: Disable Authentication Type: Auto Basic Rate: Default Transmission Rate: Auto N Transmission Rate: Auto CTS Protection Mode: Disable Beacon Interval: 100 DTIM Interval: 1 Fragmentation Threshold: 2346 RTS Threshold: 2346

  Read the article

• Book Review Charlene Li's New Book: Open Leadership

  - by david.talamelli

  A few weeks ago, I was surprised when I looked in our mail box. I had received an Advance Copy of Charlene Li's new book titled "Open Leadership: How Social Technology Can Transform the Way You Lead". Charlene sent a tweet a while back asking anyone interested in receiving the book to submit their details. I sent off my details and didn't think I would hear anything back, so it was a pleasant surprise. With that I almost feel bad that it has taken me 3 weeks to read her book. It took this long mainly because it has been hard to fit in some quality reading time for myself with work, the kids, volunteering, etc..... I am happy to report I have finished her book and wanted to run through my initial thoughts with you. I first came across Charlene Li after reading her book "Groundswell" a few years ago, her latest book "Open Leadership" is a follow on from Groundswell and to me it seems like a natural progression from the question "Ok the business landscape is changing, what do we do now?" For me these two books have a different writing style to them. Groundswell from memory spoke about broad social media concepts and adoption and alerted us to some of the changes taking place in the SM landscape. Open Leadership seems to be focussed on taking those broad concepts and finding ways to implement them into your environment. That is breaking broad concepts down into individual action items that can be measured and analysed. As the business world changes Leaders must change their approach and let go of control to more control. One of the things I love reading about is seeing real life examples of how people and organisations are making these things happen. In this book Charlene has collected some great collateral and case studies from companies such as Cisco, Best Buy, The Red Cross and The State Bank of India (as a side-note, I wish now that I submitted my input for the Leaders I work with here at Oracle - there are some great examples here of people who empower their staff). As society becomes more adept at using social media it is inevitable that Leaders must become open with their employees, clients and partners. From the book some of the key points I took away are (I actually took away a lot more from this book, this is just an overview) : 1) Organisations should encourage risk taking. Without being a "hacker", how can we improve ourselves, our processes, our business, etc... The old saying you only fail by not trying applies here. If Leaders create a culture where people are afraid to stick their neck out - how will you innovate? 2) Leaders need to lead by example - if you want to promote an open and transparent business, a Leader needs to exemplify the traits they would like to see out of their employees. 3) The definition of a Leader is changing, open leadership is about being a catalyst to change that uses networks to spread a vision as opposed to traditional leadership that is viewed as a role. 4) There is a cultural and business shift taking place. Information is more wide-spread and is being disseminated faster than any other time in the past. Leaders who are open and transparent will thrive in this new business environment. 5) Leadership is not defined by a title - it is defined by a person's actions. Also anyone can be a Leader or has Leadership potential in them- it is a matter of drawing that out of people. I found this book useful and I also found myself looking at my own actions and the actions of others around me (including my management) to see how open and transparent I am in my work. For me I am glad I read this book as it validated my own thoughts of the changes we are seeing take place. This book has certainly given me some new ideas and helped me push my own boundaries of what I can do. The book has a number of action plans at the end of some of the chapters such as "Conducting you Openness Audit" that I think have helped me take thoughts and ideas and turn them into concrete action items. I have included a link to the introduction of the book here if anyone wants to have a read of it. If anyone else has read this book, it would be great to hear your thoughts/comments/review. Leave your comments below. This article was originally posted on David Talamelli's Blog - David's Journal on Tap

  Read the article

• About Me

  - by Jeffrey West

  I’m new to blogging.  This is the second blog post that I have written, and before I go too much further I wanted the readers of my blog to know a bit more about me… Kid’s Stuff By trade, I am a programmer (or coder, developer, engineer, architect, etc).  I started programming when I was 12 years old.  When I was 7, we got our first ‘family’ computer – an Apple IIc.  It was great to play games on, and of course what else was a 7-year-old going to do with it.  I did have one problem with it, though.  When I put in my 5.25” floppy to play a game, sometimes, instead loading my game I would get a mysterious ‘]’ on the screen with a flashing cursor.  This, of course, was not my game.  Much like the standard ‘Microsoft fix’ is to reboot, back then you would take the floppy out, shake it, and restart the computer and pray for a different result. One day, I learned at school that I could topple my nemesis – the ‘]’ and flashing cursor – by typing ‘load’ and pressing enter.  Most of the time, this would load my game and then I would get to play.  Problem solved.  However, I began to wonder – what else can I make it do? When I was in 5th grade my dad got a bright idea to buy me a Tandy 1000HX.  He didn’t know what I was going to do with it, and neither did I.  Least of all, my mom wasn’t happy about buying a 5th grader a $1,000 computer.  Nonetheless, Over time, I learned how to write simple basic programs out of the back of my Math book: 10 x=5 20 y=6 30 PRINT x+y That was fun for all of about 5 minutes.  I needed more – more challenges, more things that I could make the computer do.  In order to quench this thirst my parents sent me to National Computer Camps in Connecticut.  It was one of the best experiences of my childhood, and I spent 3 weeks each summer after that learning BASIC, Pascal, Turbo C and some C++.  There weren’t many kids at the time who knew anything about computers, and lets just say my knowledge of and interest in computers didn’t score me many ‘cool’ points.  My experiences at NCC set me on the path that I find myself on now, and I am very thankful for the experience.  Real Life I have held various positions in the past at different levels within the IT layer cake.  I started out as a Software Developer for a startup in the Dallas, TX area building software for semiconductor testing statistical process control and sampling.  I was the second Java developer that was hired, and the ninth employee overall, so I got a great deal of experience developing software.  Since there weren’t that many people in the organization, I also got a lot of field experience which meant that if I screwed up the code, I got yelled at (figuratively) by both my boss AND the customer.  Fun Times!  What made it better was that I got to help run pilot programs in Taiwan, Singapore, Malaysia and Malta.  Getting yelled at in Taiwan is slightly less annoying that getting yelled at in Dallas… I spent the next 5 years at Accenture doing systems integration in the ‘SOA’ group.  I joined as a Consultant and left as a Senior Manager.  I started out writing code in WebLogic Integration and left after I wrapped up project where I led a team of 25 to develop the next generation of a digital media platform to deliver HD content in a digital format.  At Accenture, I had the pleasure of working with some truly amazing people – mentoring some and learning from many others – and on some incredible real-world IT projects.  Given my background with the BEA stack of products I was often called in to troubleshoot and tune WebLogic, ALBPM and ALSB installations and have logged many hours digging through thread dumps, running performance tests with SoapUI and decompiling Java classes we didn’t have the source for so I could see what was going on in the code. I am now a Senior Principal Product Manager at Oracle in the Application Grid practice.  The term ‘Application Grid’ refers to a collection of software and hardware products within Oracle that enables customers to build horizontally scalable systems.  This collection of products includes WebLogic, GlassFish, Coherence, Tuxedo and the JRockit/HotSpot JVMs (HotSprocket, maybe?).  Now, with the introduction of Exalogic it has grown to include hardware as well. Wrapping it up… I love technology and have a diverse background ranging from software development to HW and network architecture & tuning.  I have held certifications for being an Oracle Certified DBA, MSCE and Cisco Certified Network Professional (CCNP), among others and I have put those to great use over my career.  I am excited about programming & technology and I enjoy helping people learn and be successful.  If you are having challenges with WebLogic, BPM or Service Bus feel free to reach out to me and I’ll be happy to help as I have time. Thanks for stopping by!   --Jeff

  Read the article

• Eloqua Experience 2013: Mystique, Modern Marketing and Masterful Engagement

  - by Mike Stiles

  The following is a guest post from Erick Mott, a social business leader at Oracle Eloqua. There’s a growing gap between 20th century marketing and a modern marketing way of doing business. I can’t think of a better example of modern marketing in action than what more than 2,000 people experienced in San Francisco at #EE13; customer-obsession, multichannel content, and real-time engagement all coming together at one extraordinary event. This was my first Eloqua Experience as a new Oracle Eloqua employee. In weeks prior, I heard about the mystique but didn’t know what to expect. What I’ve come to understand with more clarity is everything we do revolves around customer success, and we operate and educate at all times with these five tenets in mind: 1. Targeting: Really Know Your Buyer 2. Engagement: Create a 1:1 Relationship 3. Conversion: Visualize Guided Thinking 4. Analysis: Learn What’s Working 5. Marketing Technology: Enable and Extend the Cloud Product News from Eloqua Experience 2013 We made some announcements that John Stetic, VP of Products, Oracle Eloqua covers in this brief ‘Modern Marketing Minute’ video recorded after Wednesday’s keynote; summarized below, too: Oracle Eloqua AdFocus: While understanding the impact of a specific marketing channel was formerly relegated to marketers’ wish lists, the channels we now focus on are digital, social, and mobile. AdFocus gives marketers a single platform to dynamically create, manage and measure display ads alongside owned and earned media. AdFocus enables marketers to target only key accounts or prospects you want to reach with display ads, as well as provide creative content or personalized ad copy based on their persona and activities. Oracle Eloqua Profiler: The details of what we now know about customers have expanded into a universal customer profile, which can be used to create highly targeted segments. Marketers now can take data that’s not even stored in Eloqua to help targeted and score prospects for a complete, multichannel view of the customer. Profiler gives sales reps one, detailed view of the prospect to extend views beyond Oracle Eloqua asset activity (emails, forms, page views) to any external assets stored in Oracle Eloqua. Marketing Resource Management: New capabilities create more secure and controlled access to marketing resources and data. New integrations provide greater insight into campaign resources and management through a central marketing calendar and simplify resource management. Integrated Sales and Marketing Funnel: An integrated sales and marketing funnel view gives marketing and sales users, cross-functional teams, and executive management a consistent and clear view of pipeline performance. It also quickly provides users with historical metrics across different time spans and conditions. Eloqua AppCloud: More than 20 new AppCloud partners have been added to the community, which now includes 100+ apps. Eloqua AppCloud now provides modern marketers with an even broader range of marketing applications that help expand and enrich sales and marketing efforts; easily accessible in the Topliners Community. Social Capabilities: Recent integration between Oracle Eloqua and Oracle Social Relationship Management (SRM) deliver a comprehensive, scalable and integrated modern marketing solution. New capabilities include better tracking of social activities for a more complete customer profile. Engage Facebook custom audiences with AdFocus to deliver ads and meaningful experiences through trusted social networks. Biggest and Best Eloqua Experience. There’s a lot of talk in the industry about the Marketing Cloud. At Oracle Eloqua, we have been on a mission of delivering the most advanced and integrated modern marketing technology on the planet. It’s not just a concept but reality with proven execution, as seen first-hand this week in San Francisco. In this video, Kevin Akeroyd, SVP of Oracle Eloqua, provides some highlights of what made this year’s Eloqua Experience, exceptional, including Steve Woods’ presentation about the journey of modern marketers and Andrea Ward’s conversation with Vince Gilligan, creator of the Breaking Bad television series. The 2013 Markie Awards The Oracle Eloqua Marketing Cloud was best exemplified for me as 19 Markies were awarded to customers for their exceptional creativity and results as modern marketers. Wow, what a night to remember with so many committed and talented people working to create an extraordinary experience! To learn more about how to become a modern marketer, check out these resources. We look forward to seeing you next year at Eloqua Experience. More on Erick: 20 years experience at Oracle, Ektron, Sitecore, Lyris, Habeas, Nokia, creatorbase, Mark Monitor, Cisco Systems, GlobalFluency, Sun Microsystems, Philips NV, Elm Products and CBS TV. Patent holder with agency, Fortune 500, media, and startup company expertise. @mikestiles

  Read the article

• Oracle at Gartner IAM Summit Next Week

  - by Tanu Sood

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} Heading to Gartner Identity and Access Management Summit next week? As you know, one of the premier conferences for identity management specialists and security experts, the Gartner IAM Conference this year is in Las Vegas, Nevada from December 3 – 5. Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} As you pack your bags and plan your itinerary, do note that Oracle executives including Amit Jasuja, Senior Vice President, Security and Identity Management and Dave Profozich, Group Vice President along with product management and implementation experts would be in attendance. You are invited to meet with the Oracle team and mingle with our customers. We recommend you bookmark the following times and activities: Breakfast Keynote: Trends in Identity Management Tuesday, December 4, 2012 7:30 a.m. – 8:00 a.m., Octavius 16 Amit Jasuja, SVP, Security and Identity Management, Oracle Ranjan Jain, Enterprise Architect, Cisco Don’t miss the opportunity to hear from Amit Jasuja, SVP, Security and Identity Management as he discusses how mobile and social behavior are changing how organizations function, manage their workforce, and interact with their customers. Learn how these new trends are shaping the innovations in Oracle Identity Management solutions. And get a customer’s take on the new trends and their impact on the organization. Visit the Oracle Booth Mingle with peers, customers, product and implementation experts at the Oracle booth. While there, catch live demonstrations of the very latest best-in-class technologies and learn how Oracle Identity Management solutions are enabling the Social, Mobile and Cloud (SoMoClo) environments. And arm yourself with industry resources from our Virtual Collateral Rack. And don’t forget to enter for a chance to win a JAWBONE JAMBOX Wireless Speaker System while at our booth. So, see you there? Gartner Identity and Access Management Summit December 3 -5, 2012 Caesars Palace 3570 Las Vegas Blvd South Las Vegas, NV 89109

  Read the article

• OpenSwan IPSec phase #2 complications

  - by XXL

  Phase #1 (IKE) succeeds without any problems (verified at the target host). Phase #2 (IPSec), however, is erroneous at some point (apparently due to misconfiguration on localhost). This should be an IPSec-only connection. I am using OpenSwan on Debian. The error log reads the following (the actual IP-addr. of the remote endpoint has been modified): pluto[30868]: "x" #2: initiating Quick Mode PSK+ENCRYPT+PFS+UP+IKEv2ALLOW+SAREFTRACK {using isakmp#1 msgid:5ece82ee proposal=AES(12)_256-SHA1(2)_160 pfsgroup=OAKLEY_GROUP_DH22} pluto[30868]: "x" #1: ignoring informational payload, type NO_PROPOSAL_CHOSEN msgid=00000000 pluto[30868]: "x" #1: received and ignored informational message pluto[30868]: "x" #1: the peer proposed: 0.0.0.0/0:0/0 - 0.0.0.0/0:0/0 pluto[30868]: "x" #3: responding to Quick Mode proposal {msgid:a4f5a81c} pluto[30868]: "x" #3: us: 192.168.1.76<192.168.1.76[+S=C] pluto[30868]: "x" #3: them: 222.222.222.222<222.222.222.222[+S=C]===10.196.0.0/17 pluto[30868]: "x" #3: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 pluto[30868]: "x" #3: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 pluto[30868]: "x" #1: ignoring informational payload, type NO_PROPOSAL_CHOSEN msgid=00000000 pluto[30868]: "x" #1: received and ignored informational message pluto[30868]: "x" #3: next payload type of ISAKMP Hash Payload has an unknown value: 97 X pluto[30868]: "x" #3: malformed payload in packet pluto[30868]: | payload malformed after IV I am behind NAT and this is all coming from wlan2. Here are the details: default via 192.168.1.254 dev wlan2 proto static 169.254.0.0/16 dev wlan2 scope link metric 1000 192.168.1.0/24 dev wlan2 proto kernel scope link src 192.168.1.76 metric 2 Output of ipsec verify: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.37/K3.2.0-24-generic (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [OK] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] This is what happens when I run ipsec auto --up x: 104 "x" #1: STATE_MAIN_I1: initiate 003 "x" #1: received Vendor ID payload [RFC 3947] method set to=109 106 "x" #1: STATE_MAIN_I2: sent MI2, expecting MR2 003 "x" #1: received Vendor ID payload [Cisco-Unity] 003 "x" #1: received Vendor ID payload [Dead Peer Detection] 003 "x" #1: ignoring unknown Vendor ID payload [502099ff84bd4373039074cf56649aad] 003 "x" #1: received Vendor ID payload [XAUTH] 003 "x" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed 108 "x" #1: STATE_MAIN_I3: sent MI3, expecting MR3 004 "x" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp1024} 117 "x" #2: STATE_QUICK_I1: initiate 010 "x" #2: STATE_QUICK_I1: retransmission; will wait 20s for response 010 "x" #2: STATE_QUICK_I1: retransmission; will wait 40s for response 031 "x" #2: max number of retransmissions (2) reached STATE_QUICK_I1. No acceptable response to our first Quick Mode message: perhaps peer likes no proposal 000 "x" #2: starting keying attempt 2 of at most 3, but releasing whack I have enabled NAT traversal in ipsec.conf accordingly. Here are the settings relative to the connection in question: version 2.0 config setup plutoopts="--perpeerlog" plutoopts="--interface=wlan2" dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn x authby=secret pfs=yes auto=add phase2alg=aes256-sha1;dh22 keyingtries=3 ikelifetime=8h type=transport left=192.168.1.76 leftsubnet=192.168.1.0/24 leftprotoport=0/0 right=222.222.222.222 rightsubnet=10.196.0.0/17 rightprotoport=0/0 Here are the specs provided by the other end that must be met for Phase #2: encryption algorithm: AES (128 or 256 bit) hash algorithm: SHA local ident1 (addr/mask/prot/port): (10.196.0.0/255.255.128.0/0/0) local ident2 (addr/mask/prot/port): (10.241.0.0/255.255.0.0/0/0) remote ident (addr/mask/prot/port): (x.x.x.x/x.x.x.x/0/0) (internal network or localhost) Security association lifetime: 4608000 kilobytes/3600 seconds PFS: DH group2 So, finally, what might be the cause of the issue that I am experiencing? Thank you.

  Read the article

• Users loggin to 3Com switches authenticated by radius not getting admin priv and no access available

  - by 3D1L

  Hi, Following the setup that I have for my Cisco devices, I got some basic level of functionality authenticating users that loggin to 3Com switches authenticated against a RADIUS server. Problem is that I can not get the user to obtain admin privileges. I'm using Microsoft's IAS service. According to 3Com documentation when configuring the access policy on IAS the value of 010600000003 have to be used to specify admin access level. That value have to be input in the Dial-in profile section: 010600000003 - indicates admin privileges 010600000002 - manager 010600000001 - monitor 010600000000 - visitor Here is the configuration on the switch: radius scheme system server-type standard primary authentication XXX.XXX.XXX.XXX accounting optional key authentication XXXXXX key accounting XXXXXX domain system scheme radius-scheme system local-user admin service-type ssh telnet terminal level 3 local-user manager service-type ssh telnet terminal level 2 local-user monitor service-type ssh telnet terminal level 1 The configuration is working with the IAS server because I can check user login events with the Eventviewer tool. Here is the output of the DISPLAY RADIUS command at the switch: [4500]disp radius SchemeName =system Index=0 Type=standard Primary Auth IP =XXX.XXX.XXX.XXX Port=1645 State=active Primary Acct IP =127.0.0.1 Port=1646 State=active Second Auth IP =0.0.0.0 Port=1812 State=block Second Acct IP =0.0.0.0 Port=1813 State=block Auth Server Encryption Key= XXXXXX Acct Server Encryption Key= XXXXXX Accounting method = optional TimeOutValue(in second)=3 RetryTimes=3 RealtimeACCT(in minute)=12 Permitted send realtime PKT failed counts =5 Retry sending times of noresponse acct-stop-PKT =500 Quiet-interval(min) =5 Username format =without-domain Data flow unit =Byte Packet unit =1 Total 1 RADIUS scheme(s). 1 listed Here is the output of the DISPLAY DOMAIN and DISPLAY CONNECTION commands after users log into the switch: [4500]display domain 0 Domain = system State = Active RADIUS Scheme = system Access-limit = Disable Domain User Template: Idle-cut = Disable Self-service = Disable Messenger Time = Disable Default Domain Name: system Total 1 domain(s).1 listed. [4500]display connection Index=0 ,Username=admin@system IP=0.0.0.0 Index=2 ,Username=user@system IP=xxx.xxx.xxx.xxx On Unit 1:Total 2 connections matched, 2 listed. Total 2 connections matched, 2 listed. [4500] Here is the DISP RADIUS STATISTICS: [4500] %Apr 2 00:23:39:957 2000 4500 SHELL/5/LOGIN:- 1 - ecajigas(xxx.xxx.xxx.xxx) in un it1 logindisp radius stat state statistic(total=1048): DEAD=1046 AuthProc=0 AuthSucc=0 AcctStart=0 RLTSend=0 RLTWait=2 AcctStop=0 OnLine=2 Stop=0 StateErr=0 Received and Sent packets statistic: Unit 1........................................ Sent PKT total :4 Received PKT total:1 Resend Times Resend total 1 1 2 1 Total 2 RADIUS received packets statistic: Code= 2,Num=1 ,Err=0 Code= 3,Num=0 ,Err=0 Code= 5,Num=0 ,Err=0 Code=11,Num=0 ,Err=0 Running statistic: RADIUS received messages statistic: Normal auth request , Num=1 , Err=0 , Succ=1 EAP auth request , Num=0 , Err=0 , Succ=0 Account request , Num=1 , Err=0 , Succ=1 Account off request , Num=0 , Err=0 , Succ=0 PKT auth timeout , Num=0 , Err=0 , Succ=0 PKT acct_timeout , Num=3 , Err=1 , Succ=2 Realtime Account timer , Num=0 , Err=0 , Succ=0 PKT response , Num=1 , Err=0 , Succ=1 EAP reauth_request , Num=0 , Err=0 , Succ=0 PORTAL access , Num=0 , Err=0 , Succ=0 Update ack , Num=0 , Err=0 , Succ=0 PORTAL access ack , Num=0 , Err=0 , Succ=0 Session ctrl pkt , Num=0 , Err=0 , Succ=0 RADIUS sent messages statistic: Auth accept , Num=0 Auth reject , Num=0 EAP auth replying , Num=0 Account success , Num=0 Account failure , Num=0 Cut req , Num=0 RecError_MSG_sum:0 SndMSG_Fail_sum :0 Timer_Err :0 Alloc_Mem_Err :0 State Mismatch :0 Other_Error :0 No-response-acct-stop packet =0 Discarded No-response-acct-stop packet for buffer overflow =0 The other problem is that when the RADIUS server is not available I can not log in to the switch. The switch have 3 local accounts but none of them works. How can I specify the switch to use the local accounts in case that the RADIUS service is not available?

  Read the article

• And What's Your Brand Worth? ...anything?

  - by [email protected]

  100 Best Global Brands from Business Week Story: The Great Trust Offensive Slide Show: Top Brands 2009 Methodology: Picking the Winners The recession has presented marketing executives around the world with the toughest test of their careers. Some brands have prospered amid the hard times--or at least held their own. Others have slipped a surprising number of places on our ninth annual ranking, compiled by consultancy Interbrand. But for seven brands, impressive performances saw them race up the charts to take their place on this year's list. Here are the numbers behind the rankings Rank 2009 Rank 2008 Employer 2009 Brand value($millions) 2008 Brand value($millions) Percent change(%) Country of Ownership 1 1 Coca-Cola  68,734  66,667  3 U.S. 2 2 IBM  60,211  59,031  2 U.S. 3 3 Microsoft  56,647  59,007  -4 U.S. 4 4 GE  47,777  53,086  -10 U.S. 5 5 Nokia  34,864  35,942  -3 Finland 6 8 McDonald's  32,275  31,049  4 U.S. 7 10 Google  31,980  25,590  25 U.S. 8 6 Toyota  31,330  34,050  -8 Japan 9 7 Intel  30,636  31,261  -2 U.S. 10 9 Disney  28,447  29,251  -3 U.S. 11 12 Hewlett-Packard  24,096  23,509  2 U.S. 12 11 Mercedes-Benz  23,867  25,577  -7 Germany 13 14 Gillette  22,841  22,069  4 U.S. 14 17 Cisco  22,030  21,306  3 U.S. 15 13 BMW  21,671  23,298  -7 Germany 16 16 Louis Vuitton  21,120  21,602  -2 France 17 18 Marlboro  19,010  21,300  -11 U.S. 18 20 Honda  17,803  19,079  -7 Japan 19 21 Samsung  17,518  17,689  -1 S. Korea 20 24 Apple  15,443  13,724  12 U.S. 21 22 H&M  15,375  13,840  11 Sweden 22 15 American Express  14,971  21,940  -32 U.S. 23 26 Pepsi  13,706  13,249  3 U.S. 24 23 Oracle  13,699  13,831  -1 U.S. 25 28 Nescafe  13,317  13,055  2 Switzerland 26 29 Nike  13,179  12,672  4 U.S. 27 31 SAP  12,106  12,228  -1 Germany 28 35 Ikea  12,004  10,913  10 Sweden 29 25 Sony  11,953  13,583  -12 Japan 30 33 Budweiser  11,833  11,438  3 Belgium 31 30 UPS  11,594  12,621  -8 U.S. 32 27 HSBC  10,510  13,143  -20 Britain 33 36 Canon  10,441  10,876  -4 Japan 34 39 Kellogg's  10,428  9,710  7 U.S. 35 32 Dell  10,291  11,695  -12 U.S. 36 19 Citi  10,254  20,174  -49 U.S. 37 37 JPMorgan  9,550  10,773  -11 U.S. 38 38 Goldman Sachs  9,248  10,331  -10 U.S. 39 40 Nintendo  9,210  8,772  5 Japan 40 44 Thomson Reuters  8,434  8,313  1 Canada 41 45 Gucci  8,182  8,254  -1 Italy 42 43 Philips  8,121  8,325  -2 Netherlands 43 58 Amazon  7,858  6,434  22 U.S. 44 51 L'Oreal  7,748  7,508  3 France 45 47 Accenture  7,710  7,948  -3 U.S. 46 46 eBay  7,350  7,991  -8 U.S. 47 48 Siemens  7,308  7,943  -8 Germany 48 56 Heinz  7,244  6,646  9 U.S. 49 49 Ford  7,005  7,896  -11 U.S. 50 62 Zara  6,789  5,955  14 Spain   Valuations do not represent a guarantee of future performance of the brands or companies. Data: Interbrand, BusinessWeek

  Read the article

• Network Restructure Method for Double-NAT network

  - by Adrian

  Due to a series of poor network design decisions (mostly) made many years ago in order to save a few bucks here and there, I have a network that is decidedly sub-optimally architected. I'm looking for suggestions to improve this less-than-pleasant situation. We're a non-profit with a Linux-based IT department and a limited budget. (Note: None of the Windows equipment we have runs does anything that talks to the Internet nor do we have any Windows admins on staff.) Key points: We have a main office and about 12 remote sites that essentially double NAT their subnets with physically-segregated switches. (No VLANing and limited ability to do so with current switches) These locations have a "DMZ" subnet that are NAT'd on an identically assigned 10.0.0/24 subnet at each site. These subnets cannot talk to DMZs at any other location because we don't route them anywhere except between server and adjacent "firewall". Some of these locations have multiple ISP connections (T1, Cable, and/or DSLs) that we manually route using IP Tools in Linux. These firewalls all run on the (10.0.0/24) network and are mostly "pro-sumer" grade firewalls (Linksys, Netgear, etc.) or ISP-provided DSL modems. Connecting these firewalls (via simple unmanaged switches) is one or more servers that must be publically-accessible. Connected to the main office's 10.0.0/24 subnet are servers for email, tele-commuter VPN, remote office VPN server, primary router to the internal 192.168/24 subnets. These have to be access from specific ISP connections based on traffic type and connection source. All our routing is done manually or with OpenVPN route statements Inter-office traffic goes through the OpenVPN service in the main 'Router' server which has it's own NAT'ing involved. Remote sites only have one server installed at each site and cannot afford multiple servers due to budget constraints. These servers are all LTSP servers several 5-20 terminals. The 192.168.2/24 and 192.168.3/24 subnets are mostly but NOT entirely on Cisco 2960 switches that can do VLAN. The remainder are DLink DGS-1248 switches that I am not sure I trust well enough to use with VLANs. There is also some remaining internal concern about VLANs since only the senior networking staff person understands how it works. All regular internet traffic goes through the CentOS 5 router server which in turns NATs the 192.168/24 subnets to the 10.0.0.0/24 subnets according to the manually-configured routing rules that we use to point outbound traffic to the proper internet connection based on '-host' routing statements. I want to simplify this and ready All Of The Things for ESXi virtualization, including these public-facing services. Is there a no- or low-cost solution that would get rid of the Double-NAT and restore a little sanity to this mess so that my future replacement doesn't hunt me down? Basic Diagram for the main office: These are my goals: Public-facing Servers with interfaces on that middle 10.0.0/24 network to be moved in to 192.168.2/24 subnet on ESXi servers. Get rid of the double NAT and get our entire network on one single subnet. My understanding is that this is something we'll need to do under IPv6 anyway, but I think this mess is standing in the way.

  Read the article

• Can't send commands via SSH to Juniper firewalls

  - by Massimo

  I have some Juniper SSG firewalls which I need to manage, and I'd like to be able to send commands to them from some monitoring scripts. I configured SSH access using public keys, and I'm able to automatically login to the firewalls. When I run SSH interactively, everything works fine: $ssh <firewall IP> FIREWALL-> <command> <command output> FIREWALL-> exit Connection to <firewall IP> closed. $ But when I try to run the command from the command line, it doesn't work: $ssh <firewall IP> <command> $ This, of course, works fine when sending a command to a remote Linux box: $ssh <linux box IP> <command> <command output> $ Why is this happening? What is the difference between running SSH interactively and specifying the command to run on the SSH command line? Update: It also works fine with a Cisco router. Only these Juniper firewalls seem to behave this way. From the debug output from SSH, it looks like the connection gets established correctly, but the Juniper box replies with an EOF when sending the command, while instead the Linux box replies with the actual command output: Linux: debug1: Authentication succeeded (publickey). debug1: channel 0: new [client-session] debug2: channel 0: send open debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending command: uptime debug2: channel 0: request exec confirm 0 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug2: channel 0: rcvd adjust 131072 debug1: client_input_channel_req: channel 0 rtype exit-status reply 0 16:44:44 up 25 days, 1:06, 3 users, load average: 0.08, 0.02, 0.01 debug2: channel 0: rcvd eof debug2: channel 0: output open -> drain debug2: channel 0: obuf empty debug2: channel 0: close_write debug2: channel 0: output drain -> closed debug2: channel 0: rcvd close debug2: channel 0: close_read debug2: channel 0: input open -> closed debug2: channel 0: almost dead debug2: channel 0: gc: notify user debug2: channel 0: gc: user detached debug2: channel 0: send close debug2: channel 0: is dead debug2: channel 0: garbage collecting debug1: channel 0: free: client-session, nchannels 1 debug1: Transferred: stdin 0, stdout 0, stderr 0 bytes in 0.1 seconds debug1: Bytes per second: stdin 0.0, stdout 0.0, stderr 0.0 debug1: Exit status 0 Juniper: debug1: Authentication succeeded (publickey). debug1: channel 0: new [client-session] debug2: channel 0: send open debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending environment. debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug1: Sending command: get system debug2: channel 0: request exec confirm 0 debug2: callback done debug2: channel 0: open confirm rwindow 2048 rmax 1024 debug2: channel 0: rcvd eof debug2: channel 0: output open -> drain debug2: channel 0: obuf empty debug2: channel 0: close_write debug2: channel 0: output drain -> closed debug1: client_input_channel_req: channel 0 rtype exit-status reply 0 debug2: channel 0: rcvd close debug2: channel 0: close_read debug2: channel 0: input open -> closed debug2: channel 0: almost dead debug2: channel 0: gc: notify user debug2: channel 0: gc: user detached debug2: channel 0: send close debug2: channel 0: is dead debug2: channel 0: garbage collecting debug1: channel 0: free: client-session, nchannels 1 debug1: Transferred: stdin 0, stdout 0, stderr 0 bytes in 0.2 seconds debug1: Bytes per second: stdin 0.0, stdout 0.0, stderr 0.0 debug1: Exit status 1

  Read the article

• Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

  - by Steven

  We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

  Read the article

• It was a figure of speech!

  - by Ratman21

  Yesterday I posted the following as attention getter / advertisement (as well as my feelings). In the groups, (I am in) on the social networking site, LinkedIn and boy did I get responses.    I am fighting mad about (a figure of speech, really) not having a job! Look just because I am over 55 and have gray hair. It does not mean, my brain is dead or I can no longer trouble shoot a router or circuit or LAN issue. Or that I can do “IT” work at all. And I could prove this if; some one would give me at job. Come on try me for 90 days at min. wage. I know you will end up keeping me (hope fully at normal pay) around. Is any one hearing me…come on take up the challenge!     This was the responses I got.   I hear you. We just need to retrain and get our skills up to speed is all. That is what I am doing. I have not given up. Just got to stay on top of the game. Experience is on our side if we have the credentials and we are reasonable about our salaries this should not be an issue.   Already on it, going back to school and have got three certifications (CompTIA A+, Security+ and Network+. I am now studying for my CISCO CCNA certification. As to my salary, I am willing to work at very reasonable rate.   You need to re-brand yourself like a product, market and sell yourself. You need to smarten up, look and feel a million dollars, re-energize yourself, regain your confidents. Either start your own business, or re-write your CV so it stands out from the rest, get the template off the internet. Contact every recruitment agent in your town, state, country and overseas, and on the web. Apply to every job you think you could do, you may not get it but you will make a contact for your network, which may lead to a job at the end of the tunnel. Get in touch with everyone you know from past jobs. Do charity work. I maintain the IT Network, stage electrical and the Telecom equipment in my church,   Again already on it. I have email the world is seems with my resume and cover letters. So far, I have rewritten or had it rewrote, my resume and cover letters; over seven times so far. Re-energize? I never lost my energy level or my self-confidents in my work (now if could get some HR personal to see the same). I also volunteer at my church, I created and maintain the church web sit.   I share your frustration. Sucks being over 50 and looking for work. Please don't sell yourself short at min wage because the employer will think that’s your worth. Keep trying!!   I never stop trying and min wage is only for 90 days. If some one takes up the challenge. Some post asked if I am keeping up technology.   Do you keep up with the latest technology and can speak the language fluidly?   Yep to that and as to speaking it also a yep! I am a geek you know. I heard from others over the 50 year mark and younger too.   I'm with you! I keep getting told that I don't have enough experience because I just recently completed a Masters level course in Microsoft SQL Server, which gave me a project-intensive equivalent of between 2 and 3 years of experience. On top of that training, I have 19 years as an applications programmer and database administrator. I can normalize rings around experienced DBAs and churn out effective code with the best of them. But my 19 years is worthless as far as most recruiters and HR people are concerned because it is not the specific experience for which they're looking. HR AND RECRUITERS TAKE NOTE: Experience, whatever the language, translates across platforms and technology! By the way, I'm also over 55 and still have "got it"!   I never lost it and I also can work rings round younger techs.   I'm 52 and female and seem to be having the same issues. I have over 10 years experience in tech support (with a BS in CIS) and can't get hired either.   Ow, I only have an AS in computer science along with my certifications.   Keep the faith, I have been unemployed since August of 2008. I agree with you...I am willing to return to the beginning of my retail career and work myself back through the ranks, if someone will look past the grey and realize the knowledge I would bring to the table.   I also would like some one to look past the gray.   Interesting approach, volunteering to work for minimum wage for 90 days. I'm in the same situation as you, being 55 & balding w/white hair, so I know where you're coming from. I've been out of work now for a year. I'm in Michigan, where the unemployment rate is estimated to be 15% (the worst in the nation) & even though I've got 30+ years of IT experience ranging from mainframe to PC desktop support, it's difficult to even get a face-to-face interview. I had one prospective employer tell me flat out that I "didn't have the energy required for this position". Mostly I never get any feedback. All I can say is good luck & try to remain optimistic.   He said WHAT! Yes remaining optimistic is key. Along with faith in God. Then there was this (for lack of better word) jerk.   Give it up already. You were too old to work in high tech 10 years ago. Scratch that, 20 years ago! Try selling hot dogs in front of Fry's Electronics. At least you would get a chance to eat lunch with your previous colleagues....   You know funny thing on this person is that I checked out his profile. He is older than I am.

  Read the article

• Openswan + xl2tpd connections time out after a while

  - by Halfgaar

  I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

  Read the article

• Allow Incoming Responses Apache. On Ubuntu 11.10 - Curl

  - by Daniel Adarve

  I'm trying to get a Curl Response from an outside server, however I noticed I cant neither PING the server in question nor connect to it. I tried disabling the iptables firewall but I had no success. My server is running behind a Cisco Linksys WRTN310N Router with the DD-wrt firmware Installed. In which I already disabled the firewall. Here are my network settings: Ifconfig eth0 Link encap:Ethernet HWaddr 00:26:b9:76:73:6b inet addr:192.168.1.120 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:b9ff:fe76:736b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:49713 errors:0 dropped:0 overruns:0 frame:0 TX packets:30987 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52829022 (52.8 MB) TX bytes:5438223 (5.4 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:341 errors:0 dropped:0 overruns:0 frame:0 TX packets:341 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:27604 (27.6 KB) TX bytes:27604 (27.6 KB) /etc/resolv.conf nameserver 192.168.1.1 /etc/nsswitch.com passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis /etc/host.conf order hosts,bind multi on /etc/hosts 127.0.0.1 localhost 127.0.0.1 callcenter # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.120 netmask 255.255.255.0 network 192.168.1.1 broadcast 192.168.1.255 gateway 192.168.1.1 The Url to which im trying to get a connection to is https://www.veripayment.com/integration/index.php When I ping it on terminal heres what I get daniel@callcenter:~$ ping https://www.veripayment.com/integration/index.php ping: unknown host https://www.veripayment.com/integration/index.php daniel@callcenter:~$ ping www.veripayment.com PING www.veripayment.com (69.172.200.5) 56(84) bytes of data. --- www.veripayment.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms PHP Function in codeigniter public function authorizePayment(){ //--------------------------------------------------- // Authorize a payment //--------------------------------------------------- // Get variables from POST array $post_str = "action=payment&business=" .urlencode($this->input->post('business')) ."&vericode=" .urlencode($this->input->post('vericode')) ."&item_name=" .urlencode($this->input->post('item_name')) ."&item_code=" .urlencode($this->input->post('item_code')) ."&quantity=" .urlencode($this->input->post('quantity')) ."&amount=" .urlencode($this->input->post('amount')) ."&cc_type=" .urlencode($this->input->post('cc_type')) ."&cc_number=" .urlencode($this->input->post('cc_number')) ."&cc_expdate=" .urlencode($this->input->post('cc_expdate_year')).urlencode($this->input->post('cc_expdate_month')) ."&cc_security_code=" .urlencode($this->input->post('cc_security_code')) ."&shipment=" .urlencode($this->input->post('shipment')) ."&first_name=" .urlencode($this->input->post('first_name')) ."&last_name=" .urlencode($this->input->post('last_name')) ."&address=" .urlencode($this->input->post('address')) ."&city=" .urlencode($this->input->post('city')) ."&state_or_province=" .urlencode($this->input->post('state_or_province')) ."&zip_or_postal_code=" .urlencode($this->input->post('zip_or_postal_code')) ."&country=" .urlencode($this->input->post('country')) ."&shipping_address=" .urlencode($this->input->post('shipping_address')) ."&shipping_city=" .urlencode($this->input->post('shipping_city')) ."&shipping_state_or_province=" .urlencode($this->input->post('shipping_state_or_province')) ."&shipping_zip_or_postal_code=".urlencode($this->input->post('shipping_zip_or_postal_code')) ."&shipping_country=" .urlencode($this->input->post('shipping_country')) ."&phone=" .urlencode($this->input->post('phone')) ."&email=" .urlencode($this->input->post('email')) ."&ip_address=" .urlencode($this->input->post('ip_address')) ."&website_unique_id=" .urlencode($this->input->post('website_unique_id')); // Send URL string via CURL $backendUrl = "https://www.veripayment.com/integration/index.php"; $this->curl->create($backendUrl); $this->curl->post($post_str); $return = $this->curl->execute(); $result = array(); // Explode array where blanks are found $resparray = explode(' ', $return); if ($resparray) { // save results into an array foreach ($resparray as $resp) { $keyvalue = explode('=', $resp); if(isset($keyvalue[1])){ $result[$keyvalue[0]] = str_replace('"', '', $keyvalue[1]); } } } return $result; } This gets an empty result array. This function however works well in the previous server where the script was hosted before. No modifications where made whatsoever Thanks in Advance

  Read the article

• Cluster failover and strange gratuitous arp behavior

  - by lazerpld

  I am experiencing a strange Windows 2008R2 cluster related issue that is bothering me. I feel that I have come close as to what the issue is, but still don't fully understand what is happening. I have a two node exchange 2007 cluster running on two 2008R2 servers. The exchange cluster application works fine when running on the "primary" cluster node. The problem occurs when failing over the cluster ressource to the secondary node. When failing over the cluster to the "secondary" node, which for instance is on the same subnet as the "primary", the failover initially works ok and the cluster ressource continues to work for a couple of minutes on the new node. Which means that the recieving node does send out a gratuitous arp reply packet that updated the arp tables on the network. But after x amount of time (typically within 5 minutes time) something updates the arp-tables again because all of a sudden the cluster service does not answer to pings. So basically I start a ping to the exchange cluster address when its running on the "primary node". It works just great. I failover the cluster ressource group to the "secondary node" and I only have loss of one ping which is acceptable. The cluster ressource still answers for some time after being failed over and all of a sudden the ping starts timing out. This is telling me that the arp table initially is updated by the secondary node, but then something (which I haven't found out yet) wrongfully updates it again, probably with the primary node's MAC. Why does this happen - has anyone experienced the same problem? The cluster is NOT running NLB and the problem stops immidiately after failing over back to the primary node where there are no problems. Each node is using NIC teaming (intel) with ALB. Each node is on the same subnet and has gateway and so on entered correctly as far as I am concerned. Edit: I was wondering if it could be related to network binding order maybe? Because I have noticed that the only difference I can see from node to node is when showing the local arp table. On the "primary" node the arp table is generated on the cluster address as the source. While on the "secondary" its generated from the nodes own network card. Any input on this? Edit: Ok here is the connection layout. Cluster address: A.B.6.208/25 Exchange application address: A.B.6.212/25 Node A: 3 physical nics. Two teamed using intels teaming with the address A.B.6.210/25 called public The last one used for cluster traffic called private with 10.0.0.138/24 Node B: 3 physical nics. Two teamed using intels teaming with the address A.B.6.211/25 called public The last one used for cluster traffic called private with 10.0.0.139/24 Each node sits in a seperate datacenter connected together. End switches being cisco in DC1 and NEXUS 5000/2000 in DC2. Edit: I have been testing a little more. I have now created an empty application on the same cluster, and given it another ip address on the same subnet as the exchange application. After failing this empty application over, I see the exact same problem occuring. After one or two minutes clients on other subnets cannot ping the virtual ip of the application. But while clients on other subnets cannot, another server from another cluster on the same subnet has no trouble pinging. But if i then make another failover to the original state, then the situation is the opposite. So now clients on same subnet cannot, and on other they can. We have another cluster set up the same way and on the same subnet, with the same intel network cards, the same drivers and same teaming settings. Here we are not seeing this. So its somewhat confusing. Edit: OK done some more research. Removed the NIC teaming of the secondary node, since it didnt work anyway. After some standard problems following that, I finally managed to get it up and running again with the old NIC teaming settings on one single physical network card. Now I am not able to reproduce the problem described above. So it is somehow related to the teaming - maybe some kind of bug? Edit: Did some more failing over without being able to make it fail. So removing the NIC team looks like it was a workaround. Now I tried to reestablish the intel NIC teaming with ALB (as it was before) and i still cannot make it fail. This is annoying due to the fact that now i actually cannot pinpoint the root of the problem. Now it just seems to be some kind of MS/intel hick-up - which is hard to accept because what if the problem reoccurs in 14 days? There is a strange thing that happened though. After recreating the NIC team I was not able to rename the team to "PUBLIC" which the old team was called. So something has not been cleaned up in windows - although the server HAS been restarted! Edit: OK after restablishing the ALB teaming the error came back. So I am now going to do some thorough testing and i will get back with my observations. One thing is for sure. It is related to Intel 82575EB NICS, ALB and Gratuitous Arp.

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

< Previous Page | 41 42 43 44 45 46  | Next Page >