Search Results

Search found 1167 results on 47 pages for 'modem'.

Page 45/47 | < Previous Page | 41 42 43 44 45 46 47  | Next Page >

• NIC is receiving, but not transmitting at all?

  - by Shtééf

  I'm trying to fix a very strange problem remotely on a machine at a customer site. The machine is a Dell PowerEdge, I believe a 1950 (haven't verified, but the lspci output matches specs I found.) The machine has two similar NICs, identified as Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) by lspci, and using the bnx2 driver. (I suspect these are on-board and on the same controller, which is what I'm accustomed to for this type of machine.) The primary interface eth0 works perfectly, and is in fact how I am ssh'd in. However, the secondary interface eth1 is not transmitting. I can see this in ifconfig output, for example, where the TX field is always 0. However, it is receiving, and tcpdump shows ARP requests coming from the ISP's gateway on the other side. The interface is physically connected to a Siemens BSTU4 modem, configured by the ISP. The link is properly set to 10MBps and full duplex, without negotation, as the ISP requested. A small /30 subnet is configured. For the sake of anonimity, let's say the machine is 3.3.3.2/30, and the ISP's gateway .1. The machine has no firewall settings whatsoever. Even running something like arping -I eth1 3.3.3.1, and running tcpdump alongside, shows no traffic whatsoever being transmitted on the interface. (But the other side keeps steadily sending ARP requests, and that is all that can be seen.) What could be causing this? Here's some output, anonymized, which may hopefully help: $ ethtool eth1 Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off Supports Wake-on: d Wake-on: d Link detected: yes $ ip link show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:15:c5:xx:xx:xx brd ff:ff:ff:ff:ff:ff $ ip -4 addr show eth1 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 inet 3.3.3.2/30 brd 3.3.3.3 scope global eth1 $ ip -4 route show match 3.3.3.0/30 3.3.3.0/30 dev eth1 proto kernel scope link src 3.3.3.2 default via 10.0.0.5 dev eth0

  Read the article

• How to configure DD-WRT routing table when creating an isolated network segment for PCI C VT compliance

  - by tetranz

  I'm the volunteer support and system admin person at a small private school. We need to setup a PCI compliant Windows PC as a virtual terminal for credit card processing. I've read questionnaire SAQ C-VT and, to quote, this computer needs to be accessed: "via a computer that is isolated in a single location, and is not connected to other locations or systems within your environment (this can be achieved via a firewall or network segmentation to isolate the computer from other systems)" Our setup is as follows: DSL modem from ISP is setup to be a "transparent pipe" with no extra services. That goes into the WAN port of Linksys WRT54-GL running a DD-WRT. The LAN is 192.168.1.x. There are a couple of other WRT54-GL / DD-WRT devices. One is used as a wireless AP and another is a client bridge. To isolate the VT (virtual terminal) machine, I have another DD-WRT device. Its WAN is connected to a port on the 192.168.1.x LAN. The virtual terminal machine is connected to its LAN which is at 192.168.10.x. The SPI Firewall etc is turned on. It's basically the default DD-WRT gateway setup where the "ISP" is our own LAN. That's working. All incoming traffic to the VT machine is blocked, including from our own LAN. The VT can access the internet BUT, and here's the problem, it can also ping any of the computers on the 192.168.1.x LAN. I think I need to stop that. I'm guessing that I could do something with the Static Routing table in the VT machine's DD-WRT device. I need to route anything going to 192.168.1.x other than the gateway which is 192.168.1.1 to 0.0.0.0 or something like that. That's where I'm stuck at the end of my knowledge. Or ... do I need to get yet another DD-WRT so the network is "balanced". Maybe I need to have the internet from the DSL going into a DD-WRT which has only two devices on its LAN i.e., two other DD-WRTs, one for the main LAN and one for the VT. I think that would do but I'd like to avoid the extra cost and complexity if I don't need it. Thanks

  Read the article

• Frequent and weird wifi disconnections

  - by Sidou

  How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

  Read the article

• weird SSH connection timed out

  - by bran

  This problem started when I tried to login to my brand spaning new VPS server. I remember that in my first SSH try on the server I actually got prompt for password several times which would mean that there is no port blocking problem from my isp. Since the password did'nt work for me (for some reason). I had a lot of authentication failure. After that attempting to log in to the server just timed out. I did the same at mediatemple (which used to work before with sftp) and put in wrong password and now trying to ssh (or even SFTP) gives me timeout error. So some kind of security feature is preventing me from trying too many times to log in, either from my side or from the server side. Any idea what it could be? TRaceroute and ping works on the ips. I am using a zyxel wimax modem (max-206m1r - if that's relevent) c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.136 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.131 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] -vv OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to 87.117.249.227 [87.117.249.227] port 22. debug1: connect to address 87.117.249.227 port 22: Connection timed out ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com Could not create directory '/home/pavs/.ssh'. The authenticity of host 's122797.gridserver.com (205.186.175.110)' can't be est ablished. RSA key fingerprint is 33:24:1e:38:bc:fd:75:02:81:d8:39:42:16:f6:f6:ff. Are you sure you want to continue connecting (yes/no)? yes Failed to add the host to the list of known hosts (/home/pavs/.ssh/known_hosts). Password: Password: Password: [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 205.186.175.110: 2: Too many authentication failures fo r pavs c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• Ubuntu 11.10 firewall/gateway - no client internet access

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• All internet requests in Windows time out

  - by Brandon

  So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

  Read the article

• FTP server questions

  - by Brad

  I'm currently trying to set up a home FTP server using debian and proftpd and I've run into a problem that has me confused. I have most things set up already, I believe, but I cannot access my ftp server using my external ip. I've forwarded the correct port on my router and I've checked http://www.yougetsignal.com/tools/open-ports/ to be sure that it is, in fact, opened. I've used telnet locally on my server to check that the port accepts connections. I am able to use ftp via LAN. But, I still cannot access anything externally. I'm thinking that there's still some router configuration to be done in order to fix this, such as routing all connections on my ftp port to my server via the internal ip, but I can't find any option on my router to do this. Is this a necessary step? There is an option to use DMZ hosting, but I'd rather avoid it if possible. I can provide additional information as requested, please let me know any information that you think could help at all. Thanks. -Brad PS - I have a Telus Actiontec Modem/Router Update - !! Trying my ftp server out at work, worked! I guess I did set it up correctly after all. What is confusing me, though, is why doesn't the server allow me to connect locally anymore? That seems very weird to me. Also, I don't really understand why I am denied outright if I attempt to connect from the same network using the external address. I'll look into it more when I get home, but thank you guys for your help. Update 2 - I found the problem with not being able to connect locally anymore. I was setting the masquerade address to my external IP and for some reason that was causing it to hang on MLSD when I connected using my LAN address. I've removed the masquerade address and I'm going to check if I need it at work tomorrow. I'll update this page if I find anything.

  Read the article

• Why does pinging a local router return "Destination Host Unreachable"?

  - by Matt H

  I have two tomato routers. One is bridged wirelessly with the other. I have a new server on the network. It's running Ubuntu Server 11.04. They are all connected like this: A - Linux PC B - New Server C - Mac Mini D - Macbook T1 - Tomato 1 T2 - Tomato 2 They are connected like so: A -----+-T1 ==== wireless bridge ==== T2----- ADSL modem | | C & D Connected wirelessly to T2 B -----+ A, C & D do not experience any issues. I have an active SSH session to B from A and it's not experiencing any loss. B, the new server occasionally cannot ping T2 and therefore cannot connect to the internet. However, A can always contact B and B can ping A and B When the network is lost, B can still ping T1, but not T2 yet at the same as B has lost connection to T2, A can still ping T2. Any ideas on what this could be? there is nothing that gives any clues in any of the logs on either router or the linux server. One thing that is interesting is that I set up a ping running between B and T2. T2 has the IP address 192.68.1.1 Here is what I am seeing: From 192.168.1.1 icmp_seq=26 Destination Host Unreachable From 192.168.1.1 icmp_seq=27 Destination Host Unreachable From 192.168.1.1 icmp_seq=28 Destination Host Unreachable From 192.168.1.1 icmp_seq=29 Destination Host Unreachable From 192.168.1.1 icmp_seq=30 Destination Host Unreachable From 192.168.1.1 icmp_seq=31 Destination Host Unreachable From 192.168.1.1 icmp_seq=33 Destination Host Unreachable From 192.168.1.1 icmp_seq=34 Destination Host Unreachable From 192.168.1.1 icmp_seq=35 Destination Host Unreachable 64 bytes from 192.168.1.1: icmp_req=36 ttl=63 time=3.40 ms 64 bytes from 192.168.1.1: icmp_req=37 ttl=63 time=5.70 ms 64 bytes from 192.168.1.1: icmp_req=38 ttl=63 time=2.25 ms 64 bytes from 192.168.1.1: icmp_req=39 ttl=63 time=2.18 ms 64 bytes from 192.168.1.1: icmp_req=40 ttl=63 time=3.12 ms 64 bytes from 192.168.1.1: icmp_req=41 ttl=63 time=2.15 ms 64 bytes from 192.168.1.1: icmp_req=42 ttl=63 time=1.97 ms 64 bytes from 192.168.1.1: icmp_req=43 ttl=63 time= And it cycles to being reachable and not. So I guess you could say the question is, why is the router responding that it cannot be reached?

  Read the article

• How to configure sendmail to relay through a specific server

  - by ErebusBat

  I have a tiny home server setup behind my cable modem (bresnan communications). I want to be able for this box to send out email (not receive) for notifications and whatnot. What I have already done: I have installed and configured sendmail. I have added mail.bresnan.net as my SMART_HOST directive. What I belive the problem is When I attempt to send an email I get the following in my mail log: Dec 22 10:24:17 batcave sendmail[1530]: oBMHOHrs001530: from=aburns, size=140, class=0, nrcpts=1, msgid=<[email protected]>, relay=aburns@localhost Dec 22 10:24:17 batcave sm-mta[1531]: oBMHOHWZ001531: from=<[email protected]>, size=397, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Dec 22 10:24:17 batcave sendmail[1530]: oBMHOHrs001530: to=<[email protected]>, ctladdr=aburns (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30140, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (oBMHOHWZ001531 Message accepted for delivery) Dec 22 10:24:18 batcave sm-mta[1517]: oBMH9mVv001357: to=<[email protected]>, ctladdr=<[email protected]> (1000/1000), delay=00:14:30, xdelay=00:00:42, mailer=relay, pri=300339, relay=pmx0.bresnan.net. [69.145.248.1], dsn=4.0.0, stat=Deferred: Connection timed out with pmx0.bresnan.net. You can see where the message is accepted for delivery by my sendmail server, then where it attempts to hand off to bresnan's server and it timesout. This is where my question is. Asstute readers will notice that pmx0.bresnan.net is not what I have my SMART_HOST directive set as. This is the (outside?) MX server for the bresnan.com/net domain. Apparently bresnan has their network configured so that you can not access this server from within their own network and instead must use the mail.bresnan.net server (which I can connect to). The problem is that I don't know how to tell sendmail to use this server and not the domain. What I have tried Setting a hosts entry so that the pmx0 server points to the mail IP address. This doesn't work, which makes sense as sendmail is obviously doing an MX query to find the server which returns the IP so there is never a need to do a 'normal' DNS resolve so the hosts file never gets involved.

  Read the article

• Resetting root password on Fedora Core 3 - serial cable access only

  - by Sensible Eddie

  A little background: We have an old rackmount server running a customised version of Fedora, manufactured by a company called Navaho. The server is a TeamCAT, running some proprietary rubbish called Freedom2. We have to keep it going - the alternative is extraordinarily expensive, and the business is not likely to be running much longer to justify changing things. Through one means or another, it has fallen upon me to try and resolve our lack of root access. The previous admin has fallen under the proverbial bus, and nobody has any clue. We have no access to the root account for this server. ssh is running on the server, and there is one account admin that we can login with, however it has no permission to do anything (ironic...) The only other way into the server is with a null-modem serial cable. This works... up to a point. I can see the BIOS, I can see the post BIOS screen, and then I see "Starting grub", followed by another screen with about four lines of Linux information, but then it stops at that point. The server continues booting, and all services come online after around two minutes, but the serial terminal displays no more information. I understand it is possible to put Linux into "single user mode" to reset a root password, but I have no idea how to do this beyond trying to interrupt it at the grub stage listed above. When I have tried it just froze. It was almost like grub had appeared (since the server did not continue booting) but I couldn't see it on the serial terminal. Which made me think maybe the grub screen has some different serial settings? I don't know... it's the first time I've ever used serial for access! A friend of mine suggested trying to use a Fedora boot CD. We could boot from USB, so something along this approach is possible but again we still can only see what's going on with the serial terminal, so it might not be achievable. Does anyone have any suggestions for things I can try? I appreciate this is a bit of a long shot, but any assistance would be invaluable. *UPDATE 1 - 28/8/12 * - we will be making some attempts on this today and will post further details later!

  Read the article

• Local dns for testing websites using mobile devices

  - by Morpheu5

  Hi. I have no idea where to start from so sorry in advance if this topic has already been discussed. I usually develop web sites using my laptop as a development server, and recently I needed to test a web site using various mobile devices that can connect via wifi. Having no real AP, I set up a ad-hoc network using my laptop's wireless card and the devices can correctly browse the Internet and access the laptop's web server. The setup is as follows: subnet: 192.168.1.0/24 gateway to the Internet (wired adsl router/modem): 192.168.1.1 laptop: 192.168.1.64 (eth0, wired if connected to the gateway) and 192.168.1.32 (eth1, wifi if somewhat bridged to eth0) mobile devices (same for all, I only use one of them at any time for simplicity): 192.168.1.11 with default gw 192.168.1.1 Now, if I open either 192.168.1.32 or 192.168.1.64 from the mobile devices, I correctly get the default host of my Apache configuration. However I usually work with virtual hosts for many practical reasons, one of which being Drupal's peculiar implementation of multi-sites. For those who don't know how this works, Drupal takes the request's hostname and searches into its sites/ subdirectories for an appropriate configuration file. So, for example, suppose I request www.example.com, then Drupal would search for a config file in the following directories: sites/www.example.com/ sites/example.com/ sites/com/ sites/default/ So I decided to adopt the following style of virtual hosts: if the website I'm working on will be accessible using www.example.com I set up a sites/www.example.com/ directory and create a virtual host for local.www.example.com so Drupal have no trouble finding it. I've been told this is suboptimal from a dns point of view since I'd have to create an authoritative entry for example.com and turn Bind on only when I'm supposed to access the local copy, which is weird. However, if this is the only path I can follow, I still have some problems with Bind's configuration, as I couldn't find any guide that tells me in a clear, noob-friendly way, how to set up such an entry. On the other hand, I was wondering if I could set up an authoritative entry for local, so I could access www.example.com.local and tell in some way (which I don't even know if this is possible) Apache to put www.example.com instead of www.example.com.local in the relevant environment variable. Anyway, I have a last problem, sort of: when I launch Bind in debug mode with high verbosity, and make 192.168.1.32 as the primary dns for the devices, the output doesn't say anything about requests being made from the devices to Bind, so I'm not even sure it comes into play. As you can see, I'm a complete noob at these matters, but I'm eager to learn, so any help/pointer will be appreciated.

  Read the article

• Router behind Router--second router (and its clients) cannot be "seen" even after both routers are D

  - by Trioke

  Couple of terminology I guess I should get out of the way for consistency's sake throughout the post: External Router/Modem - SMC 8014WG - External IP 173.32.144.134 - Internal IP 192.168.0.1 Internal Router - LinkSys WRT120N - "External" IP of 192.168.0.175 - Internal IP 192.168.1.1 - Connected via Ethernet Cable (a really long one, from the basement to the second floor) PC - IP 192.168.200 - Connected Wirelessly via WAP2 Personal. Laptop - Used to try and diagnose the problem, a 4th machine to the setup which won't be part of the final setup once everything works. The actual problem: I've tried setting the LinkySys router as a DMZ'd client on the SMC router, and then DMZ'd the actual PC on the LinkSys. So the DMZ looks like this: On the SMZ, client with IP 192.168.0.175 is DMZ'd. On the LinkSys, client with IP 192.168.1.200 is DMZ'd. No dice. I then tried port forwarding the necessary port on the SMC to the LinkSys (lets just say, port 80). Then port forwarded Port 80 on the LinkSys to the PC. Same as the DMZ scenario above, but change DMZ with port forwarding. No dice, still :(. Now here's where I went stupid--and tell me if one should never do this--I enabled both DMZ and port forwarding at the same time. I fired up Opera--my browser of choice ;)--typed in 173.32.144.134:6333 and... ... Third time is the charm they say? Well, clearly not. Otherwise I wouldn't be here ;). To diagnose the problem, I enabled "Allow remote access to the Admin panel" on the LinkSys router, and specified port 6333 as the port to use. I port forwarded port 6333 on the SMC to 192.168.0.175, and access my external IP of 173.32.144.134:6333 in hopes of seeing the Admin panel... No dice (I think I've ran out of dice by now ;)). So to see where the problem was, I connected a laptop to the SMC via LAN cable, and typed in 192.168.0.175:6333, and viola, Admin Panel access! So the problem looks like it lies with the SMC--But that's as far as I've got, I've done the port forwarding, the DMZ'ing, and I've even disabled the built-in firewall for safe measures, but nothing worked. So, here I am. Unable to connect to the PC behind the Internal router externally, and without anything to go on other than to come here and ask for the wisdom of the the superuser folks :). If any more detail is required, just ask. (Apologies in advance, if questions should never be this long winded!)

  Read the article

• Python cannot go over internet network

  - by user1642826

  I am currently trying to work with python networking and I have reached a bit of a road block. I am not able to network with any computer but localhost, which is kind-of useless with what networking is concerned. I have tried on my local network, from one computer to another, and I have tried over the internet, both fail. The only time I can make it work is if (when running on the server's computer) it's ip is set as 'localhost' or '192.168.2.129' (computers ip). I have spent hours going over opening ports with my isp and have gotten nowhere, so I decided to try this forum. I have my windows firewall down and I have included some pictures of important screen shots. I have no idea what the problem is and this has spanned almost a year of calls to my isp. The computer, modem, and router have all been replaced in that time. Screen shots: import socket import threading import socketserver class ThreadedTCPRequestHandler(socketserver.BaseRequestHandler): def handle(self): data = self.request.recv(1024) cur_thread = threading.current_thread() response = "{}: {}".format(cur_thread.name, data) self.request.sendall(b'worked') class ThreadedTCPServer(socketserver.ThreadingMixIn, socketserver.TCPServer): pass def client(ip, port, message): sock = socket.socket(socket.AF_INET, socket.SOCK_STREAM) sock.connect((ip, port)) try: sock.sendall(message) response = sock.recv(1024) print("Received: {}".format(response)) finally: sock.close() if __name__ == "__main__": # Port 0 means to select an arbitrary unused port HOST, PORT = "192.168.2.129", 9000 server = ThreadedTCPServer((HOST, PORT), ThreadedTCPRequestHandler) ip, port = server.server_address # Start a thread with the server -- that thread will then start one # more thread for each request server_thread = threading.Thread(target=server.serve_forever) # Exit the server thread when the main thread terminates server_thread.daemon = True server_thread.start() print("Server loop running in thread:", server_thread.name) ip = '12.34.56.789' print(ip, port) client(ip, port, b'Hello World 1') client(ip, port, b'Hello World 2') client(ip, port, b'Hello World 3') server.shutdown() I do not know where the error is occurring. I get this error: Traceback (most recent call last): File "C:\Users\Dr.Frev\Desktop\serverTest.py", line 43, in <module> client(ip, port, b'Hello World 1') File "C:\Users\Dr.Frev\Desktop\serverTest.py", line 18, in client sock.connect((ip, port)) socket.error: [Errno 10061] No connection could be made because the target machine actively refused it Any help will be greatly appreciated. *if this isn't a proper forum for this, could someone direct me to a more appropriate one.

  Read the article

• How to troubleshoot port forwarding on Windows 7 (64 Bit) with ICS enabled?

  - by LearnCocos2D

  I want to forward some ports (1666 for perforce, 8081 for Hudson) on my Internet Gateway machine. This machine is running Windows 7 (64 Bit, legal, user-account) and connected to the Internet via cable modem (it's not a router). The Windows machine is sharing its Internet Connection via ICS and that works fine on all connected computers. I can access the services via the gateway's public IP (95.x.x.x) on the given ports if they are running on the gateway machine itself. I've added the ports and destination IP address (192.168.0.18) in the Internet network adapter's Advanced Settings dialog (Sharing tab). That's the same dialog where you have a list of preconfigured services like HTTP, FTP and other incoming services. When I do that I can't connect to the services anymore. For some reason port forwarding isn't working. I have uninstalled Bitdefender because I wanted to check if the Firewall interferes. I've also disabled the Windows Firewall and Defender to no avail. I tried a freeware tool that helps to setup port forwarding but that didn't work either. The target machine is a Mac OS X computer whose Firewall is disabled. The IP is static. I can successfully connect to the services using the local IP address (192.168.0.18) from two different machines, including the gateway computer. So internally and externally it seems to me that the ports are open and not blocked, and the issue is with port forwarding itself. From what I understand it should be enough to add an entry to the Advanced Settings dialog to enable port forwarding when there are no firewalls interfering. How can I troubleshoot why port forwarding isn't working for me? What steps should I follow to alleviate the issue? PS: I gladly accept command line solutions. Other things I've tried: adding an Inbound Rule to Windows Firewall for the 1666, 8081 ports trying with Windows Firewall enabled and disabled disabling/enabling the network adapter double-checked that the IP addresses are correct mapping a different incoming port to the service's actual port followed or checked the misc tips in this article What I haven't dared trying yet (let me know if it's worth a shot): disable/enable ICS remove all network adapters (via Control Panel), then re-install and re-configure them

  Read the article

• L2TP connection fails!

  - by a.toraby

  I've installed l2tp-ipsec-vpn but when I try to connect to the vpn server I get error 500. Here are the logs: Jun 17 12:54:37.449 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:54:38.858 Stopping xl2tpd: xl2tpd. Jun 17 12:54:38.859 xl2tpd[1511]: death_handler: Fatal signal 15 received Jun 17 12:54:38.872 ipsec_setup: Starting Openswan IPsec U2.6.37/K3.2.0-23-generic... Jun 17 12:54:39.027 ipsec__plutorun: Starting Pluto subsystem... Jun 17 12:54:39.033 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Jun 17 12:54:39.037 recvref[30]: Protocol not available Jun 17 12:54:39.038 xl2tpd[2442]: This binary does not support kernel L2TP. Jun 17 12:54:39.038 xl2tpd[2444]: xl2tpd version xl2tpd-1.3.1 started on atp-ThinkPad-SL410 PID:2444 Jun 17 12:54:39.038 xl2tpd[2444]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. Jun 17 12:54:39.038 xl2tpd[2444]: Forked by Scott Balmos and David Stipp, (C) 2001 Jun 17 12:54:39.038 xl2tpd[2444]: Inherited by Jeff McAdams, (C) 2002 Jun 17 12:54:39.039 xl2tpd[2444]: Forked again by Xelerance (www.xelerance.com) (C) 2006 Jun 17 12:54:39.039 xl2tpd[2444]: Listening on IP address 0.0.0.0, port 1701 Jun 17 12:54:39.040 Starting xl2tpd: xl2tpd. Jun 17 12:54:39.062 ipsec__plutorun: 002 added connection description "L2TP" Jun 17 12:55:30.753 104 "L2TP" #1: STATE_MAIN_I1: initiate Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 20s for response Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 40s for response Jun 17 12:55:30.754 003 "L2TP" #1: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008] Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [RFC 3947] method set to=109 Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109 Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [FRAGMENTATION] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [MS-Negotiation Discovery Capable] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [IKE CGA version 1] Jun 17 12:55:30.755 106 "L2TP" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Jun 17 12:55:30.755 010 "L2TP" #1: STATE_MAIN_I2: retransmission; will wait 20s for response Jun 17 12:55:30.755 003 "L2TP" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Jun 17 12:55:30.755 108 "L2TP" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Jun 17 12:55:30.756 004 "L2TP" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Jun 17 12:55:30.756 117 "L2TP" #2: STATE_QUICK_I1: initiate Jun 17 12:55:30.756 010 "L2TP" #2: STATE_QUICK_I1: retransmission; will wait 20s for response Jun 17 12:55:30.756 003 "L2TP" #2: ignoring informational payload, type IPSEC_RESPONDER_LIFETIME msgid=6b03ff69 Jun 17 12:55:30.756 003 "L2TP" #2: NAT-Traversal: received 2 NAT-OA. ignored because peer is not NATed Jun 17 12:55:30.756 003 "L2TP" #2: our client subnet returned doesn't match my proposal - us:192.168.1.3/32 vs them:109.162.174.235/32 Jun 17 12:55:30.757 003 "L2TP" #2: Allowing questionable proposal anyway [ALLOW_MICROSOFT_BAD_PROPOSAL] Jun 17 12:55:30.757 004 "L2TP" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x23af21f8 <0xdb4a87b6 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Jun 17 12:55:31.759 xl2tpd[2444]: Connecting to host x.x.x.x, port 1701 Jun 17 12:55:32.021 xl2tpd[2444]: Connection established to x.x.x.x, 1701. Local: 4720, Remote: 200 (ref=0/0). Jun 17 12:55:32.023 xl2tpd[2444]: Calling on tunnel 4720 Jun 17 12:55:32.454 xl2tpd[2444]: Call established with x.x.x.x, Local: 9667, Remote: 3, Serial: 1 (ref=0/0) Jun 17 12:55:32.456 xl2tpd[2444]: start_pppd: I'm running: Jun 17 12:55:32.456 xl2tpd[2444]: "/usr/sbin/pppd" Jun 17 12:55:32.457 xl2tpd[2444]: "passive" Jun 17 12:55:32.458 xl2tpd[2444]: "nodetach" Jun 17 12:55:32.458 xl2tpd[2444]: ":" Jun 17 12:55:32.459 xl2tpd[2444]: "file" Jun 17 12:55:32.459 xl2tpd[2444]: "/etc/ppp/L2TP.options.xl2tpd" Jun 17 12:55:32.460 xl2tpd[2444]: "ipparam" Jun 17 12:55:32.461 xl2tpd[2444]: "x.x.x.x" Jun 17 12:55:32.462 xl2tpd[2444]: "/dev/pts/1" Jun 17 12:55:32.583 pppd[2711]: Plugin passprompt.so loaded. Jun 17 12:55:32.583 pppd[2711]: pppd 2.4.5 started by root, uid 0 Jun 17 12:55:32.619 pppd[2711]: Using interface ppp0 Jun 17 12:55:32.620 pppd[2711]: Connect: ppp0 <--> /dev/pts/1 Jun 17 12:55:33.693 pppd[2711]: /usr/bin/L2tpIPsecVpn exited with code 0 Jun 17 12:55:34.454 [ERROR 404] Authentication failed: closing connection to 'L2TP' Jun 17 12:55:34.456 pppd[2711]: MS-CHAP authentication failed: E=691 Authentication failure Jun 17 12:55:34.457 pppd[2711]: CHAP authentication failed Jun 17 12:55:34.461 Stopping xl2tpd: xl2tpd. Jun 17 12:55:34.462 xl2tpd[2444]: death_handler: Fatal signal 15 received Jun 17 12:55:34.463 pppd[2711]: Modem hangup Jun 17 12:55:34.463 pppd[2711]: Connection terminated. Jun 17 12:55:34.474 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:55:34.482 pppd[2711]: Exit. Jun 17 12:55:35.587 ipsec_setup: ERROR: Module xfrm4_mode_transport is in use Jun 17 12:55:35.665 ipsec_setup: ERROR: Module esp4 is in use I had this problem by ubuntu 11.10 though I can easily connect to the server from windows. I use ubuntu 12.0 64bit

  Read the article

• I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

  - by user69670

  Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

  Read the article

• Unlimited SMS API/Gateway (Sending and Receiving)

  - by Naif

  I am creating a chat application which requires that users be able to send and receive sms messages through a web interface. It would be somewhat similar to the text messaging service available in yahoo mail or in aol instant messenger. The situation is this: Given the high quantity of messages that would be sent and received, paying on a per message basis is not economically feasible. How is it that sites such as yahoo, aim, and twitter can send and receive unlimited sms messages? Essentially, I am looking for a way to send and receive unlimited sms from my computer. Below is a list of some approaches I've come up with but have run into problems with as well. If just one of the approaches can be utilized effectively, then I am fine. As a note on the nature of my application: I will only be sending messages to users that explicitly sign up for the service and permit the receiving of messages. They can unsubscribe at any time. This is to prevent spam. I am aware of software such as Kannel which allows one to connect to a providers smsc gateway. However, this adds the risk of not being approved by the provider which would be unacceptable. Is there any way to significantly mitigate this risk? Utilizing a gateway provider eliminates this risk, but adds the issue of per message pricing. I am also aware of email to sms. However, I have done some testing with that and it appears that this method results in many messages being undelivered or delivered VERY late. If it weren't for that, this approach would have been ideal. Is there any way to negotiate with carriers to remove me from their filters (considering the nature of my service as stated before)? I could use a gsm modem, but even with an "unilimited" plan on a sim card, there are still limits (around 100,000 messages or so). Furthermore, from my understanding, gsm modems are capable of only sending out around a dozen messages per minute. I need to be able to send out as much as several hundred messages per second. During the first 2 months, around 10 messages per second would suffice. There are ways to send out ads with messages to cover the per message costs. However, this is a deal-breaker since it has a high chance of tarnishing the quality of service. Furthermore, I know it is possible to do it without such ads since yahoo, aim, and twitter do not send ads with their messages.

  Read the article

• PPPTP VPN from Ubuntu cannot connect

  - by Andrea Polci

  I'm trying to configure under Linux (Kubuntu 9.10) a VPN I already use from Windows. I installed the network-manager-pptp package and added the vpn under Network Manager. These are the parameter under "advanced" button: Authentication Methods: PAP, CHAP, MSCHAP, SMCHAP2, EAP (I tried also with MSCHAP and MSCHAP2 only) Use MPPE Encryption: yes Crypto: Any Use stateful encryption: no Compression: Allow BSD compression: yes Allow Deflate compression: yes Allow TCP header compression: yes Send PPP echo packets: no When I try to connnect it doesn't work and this is what I get in the system log: 2010-04-08 13:53:47 pcelena NetworkManager <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 4931 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections 2010-04-08 13:53:47 pcelena pppd[4932] Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN plugin state changed: 3 2010-04-08 13:53:47 pcelena pppd[4932] pppd 2.4.5 started by root, uid 0 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN connection 'MYVPN' (Connect) reply received. 2010-04-08 13:53:47 pcelena NetworkManager SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) 2010-04-08 13:53:47 pcelena NetworkManager SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. 2010-04-08 13:53:47 pcelena pppd[4932] Using interface ppp0 2010-04-08 13:53:47 pcelena pppd[4932] Connect: ppp0 <--> /dev/pts/2 2010-04-08 13:53:47 pcelena pptp[4934] nm-pptp-service-4931 log[main:pptp.c:314]: The synchronous pptp option is NOT activated 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 1, peer's call ID 14800). 2010-04-08 13:53:48 pcelena pppd[4932] CHAP authentication succeeded 2010-04-08 13:53:48 pcelena pppd[4932] CHAP authentication succeeded 2010-04-08 13:53:48 pcelena pppd[4932] LCP terminated by peer 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:929]: Call disconnect notification received (call id 14800) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:788]: Received Stop Control Connection Request. 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 4 'Stop-Control-Connection-Reply' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) 2010-04-08 13:53:48 pcelena pppd[4932] Modem hangup 2010-04-08 13:53:48 pcelena pppd[4932] Connection terminated. 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin failed: 1 2010-04-08 13:53:48 pcelena NetworkManager SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) 2010-04-08 13:53:48 pcelena pppd[4932] Exit. 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin failed: 1 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin state changed: 6 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin state change reason: 0 2010-04-08 13:53:48 pcelena NetworkManager <WARN> connection_state_changed(): Could not process the request because no VPN connection was active. 2010-04-08 13:53:48 pcelena NetworkManager <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS. 2010-04-08 13:54:01 pcelena NetworkManager <debug> [1270727641.001390] ensure_killed(): waiting for vpn service pid 4931 to exit 2010-04-08 13:54:01 pcelena NetworkManager <debug> [1270727641.001479] ensure_killed(): vpn service pid 4931 cleaned up Does anyone has suggestion on what can be the problem and how to make it work?

  Read the article

• Useful Command-line Commands on Windows

  - by Sung Meister

  The aim for this Wiki is to promote using a command to open up commonly used applications without having to go through many mouse clicks - thus saving time on monitoring and troubleshooting Windows machines. Answer entries need to specify Application name Commands Screenshot (Optional) Shortcut to commands && - Command Chaining %SYSTEMROOT%\System32\rcimlby.exe -LaunchRA - Remote Assistance (Windows XP) appwiz.cpl - Programs and Features (Formerly Known as "Add or Remove Programs") appwiz.cpl @,2 - Turn Windows Features On and Off (Add/Remove Windows Components pane) arp - Displays and modifies the IP-to-Physical address translation tables used by address resolution protocol (ARP) at - Schedule tasks either locally or remotely without using Scheduled Tasks bootsect.exe - Updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR cacls - Change Access Control List (ACL) permissions on a directory, its subcontents, or files calc - Calculator chkdsk - Check/Fix the disk surface for physical errors or bad sectors cipher - Displays or alters the encryption of directories [files] on NTFS partitions cleanmgr.exe - Disk Cleanup clip - Redirects output of command line tools to the Windows clipboard cls - clear the command line screen cmd /k - Run command with command extensions enabled color - Sets the default console foreground and background colors in console command.com - Default Operating System Shell compmgmt.msc - Computer Management control.exe /name Microsoft.NetworkAndSharingCenter - Network and Sharing Center control keyboard - Keyboard Properties control mouse(or main.cpl) - Mouse Properties control sysdm.cpl,@0,3 - Advanced Tab of the System Properties dialog control userpasswords2 - Opens the classic User Accounts dialog desk.cpl - opens the display properties devmgmt.msc - Device Manager diskmgmt.msc - Disk Management diskpart - Disk management from the command line dsa.msc - Opens active directory users and computers dsquery - Finds any objects in the directory according to criteria dxdiag - DirectX Diagnostic Tool eventvwr - Windows Event Log (Event Viewer) explorer . - Open explorer with the current folder selected. explorer /e, . - Open explorer, with folder tree, with current folder selected. F7 - View command history find - Searches for a text string in a file or files findstr - Find a string in a file firewall.cpl - Opens the Windows Firewall settings fsmgmt.msc - Shared Folders fsutil - Perform tasks related to FAT and NTFS file systems ftp - Transfers files to and from a computer running an FTP server service getmac - Shows the mac address(es) of your network adapter(s) gpedit.msc - Group Policy Editor gpresult - Displays the Resultant Set of Policy (RSoP) information for a target user and computer httpcfg.exe - HTTP Configuration Utility iisreset - To restart IIS InetMgr.exe - Internet Information Services (IIS) Manager 7 InetMgr6.exe - Internet Information Services (IIS) Manager 6 intl.cpl - Regional and Language Options ipconfig - Internet protocol configuration lusrmgr.msc - Local Users and Groups Administrator msconfig - System Configuration notepad - Notepad? ;) mmsys.cpl - Sound/Recording/Playback properties mode - Configure system devices more - Displays one screen of output at a time mrt - Microsoft Windows Malicious Software Removal Tool mstsc.exe - Remote Desktop Connection nbstat - displays protocol statistics and current TCP/IP connections using NBT ncpa.cpl - Network Connections netsh - Display or modify the network configuration of a computer that is currently running netstat - Network Statistics net statistics - Check computer up time net stop - Stops a running service. net use - Connects a computer to or disconnects a computer from a shared resource, or displays information about computer connections odbcad32.exe - ODBC Data Source Administrator pathping - A traceroute that collects detailed packet loss stats perfmon - Opens Reliability and Performance Monitor ping - Determine whether a remote computer is accessible over the network powercfg.cpl - Power management control panel applet quser - Display information about user sessions on a terminal server qwinsta - See disconnected remote desktop sessions reg.exe - Console Registry Tool for Windows regedit - Registry Editor rasdial - Connects to a VPN or a dialup network robocopy - Backup/Restore/Copy large amounts of files reliably rsop.msc - Resultant Set of Policy (shows the combined effect of all group policies active on the current system/login) runas - Run specific tools and programs with different permissions than the user's current logon provides sc - Manage anything you want to do with services. schtasks - Enables an administrator to create, delete, query, change, run and end scheduled tasks on a local or remote system. secpol.msc - Local Security Settings services.msc - Services control panel set - Displays, sets, or removes cmd.exe environment variables. set DIRCMD - Preset dir parameter in cmd.exe start - Starts a separate window to run a specified program or command start. - opens the current directory in the Windows Explorer. shutdown.exe - Shutdown or Reboot a local/remote machine subst.exe - Associates a path with a drive letter, including local drives systeminfo -Displays a comprehensive information about the system taskkill - terminate tasks by process id (PID) or image name tasklist.exe - List Processes on local or a remote machine taskmgr.exe - Task Manager telephon.cpl - Telephone and Modem properties timedate.cpl - Date and Time title - Change the title of the CMD window you have open tracert - Trace route wmic - Windows Management Instrumentation Command-line winver.exe - Find Windows Version wscui.cpl - Windows Security Center wuauclt.exe - Windows Update AutoUpdate Client

  Read the article

• VPN in Ubuntu fails every time

  - by fazpas

  I am trying to setup a vpn connection in Ubuntu 10.04 to use the service from relakks.com I used the network manager to add the vpn connection and the settings are: Gateway: pptp.relakks.com Username: user Password: pwd IPv4 Settings: Automatic (VPN) Advanced: MSCHAP & MSCHAPv2 checked Use point-to-point encryption (security:default) Allow BSD data compression checked Allow deflate data compression checked Use TCP header compression checked The connection always fail, here is the syslog: Jun 27 20:11:56 desktop NetworkManager: <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 2064 Jun 27 20:11:56 desktop NetworkManager: <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections Jun 27 20:11:56 desktop NetworkManager: <info> VPN plugin state changed: 3 Jun 27 20:11:56 desktop NetworkManager: <info> VPN connection 'Relakks' (Connect) reply received. Jun 27 20:11:56 desktop pppd[2067]: Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. Jun 27 20:11:56 desktop pppd[2067]: pppd 2.4.5 started by root, uid 0 Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:56 desktop NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp1, iface: ppp1): no ifupdown configuration found. Jun 27 20:11:56 desktop pppd[2067]: Using interface ppp1 Jun 27 20:11:56 desktop pppd[2067]: Connect: ppp1 <--> /dev/pts/0 Jun 27 20:11:56 desktop pptp[2071]: nm-pptp-service-2064 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Jun 27 20:11:57 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. Jun 27 20:11:58 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1024). Jun 27 20:11:59 desktop kernel: [ 56.564074] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=61 TOS=0x00 PREC=0x00 TTL=52 ID=40460 DF PROTO=47 Jun 27 20:11:59 desktop kernel: [ 56.944054] Inbound IN=ppp0 OUT= MAC= SRC=93.182.139.2 DST=186.110.76.26 LEN=60 TOS=0x00 PREC=0x00 TTL=52 ID=40461 DF PROTO=47 Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[pptp_read_some:pptp_ctrl.c:544]: read returned zero, peer has closed Jun 27 20:11:59 desktop pptp[2079]: nm-pptp-service-2064 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) Jun 27 20:11:59 desktop pppd[2067]: Modem hangup Jun 27 20:11:59 desktop pppd[2067]: Connection terminated. Jun 27 20:11:59 desktop NetworkManager: <info> VPN plugin failed: 1 Jun 27 20:11:59 desktop NetworkManager: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp1, iface: ppp1) Jun 27 20:11:59 desktop pppd[2067]: Exit. Does someone can identify something in the syslog? I've been googling and reading about pptp but couldn't find anything about the error "read returned zero, peer has closed"

  Read the article

• Static background noise while using new headset Ubuntu 13.04

  - by ThundLayr

  Today I bought a new gaming headset (Gx-Gaming Lychas), and when I tried to record some gameplay-comentary I noticed that there always is a static background noise, I just recorded an example so you guys can listen it (no downloaded needed): http://www47.zippyshare.com/v/65167832/file.html I'm using Kubuntu 13.04 and Kernel version is 3.8.0-19, my laptop is an Acer Travelmate 5760Z, I tried tons of configurations on Alsamixer and none of them made result, I really need to get this working so any kind of help will be very aprecciated. cat /proc/asound/cards: 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xc6400000 irq 44 cat /proc/asound/card0/codec#0 Codec: Conexant CX20588 Address: 0 AFG Function Id: 0x1 (unsol 1) Vendor Id: 0x14f1506c Subsystem Id: 0x10250574 Revision Id: 0x100003 No Modem Function Group found Default PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A State of AFG node 0x01: Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS Power: setting=D0, actual=D0 GPIO: io=4, o=0, i=0, unsolicited=1, wake=0 IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0 Node 0x10 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Headphone Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Headphone Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x4a 0x4a] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x11 [Audio Output] wcaps 0xc1d: Stereo Amp-Out R/L Control: name="Speaker Playback Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Control: name="Speaker Playback Switch", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-Out vals: [0x80 0x80] Converter: stream=8, channel=0 PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x12 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x13 [Beep Generator Widget] wcaps 0x70000c: Mono Amp-Out Control: name="Beep Playback Volume", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Control: name="Beep Playback Switch", index=0, device=0 ControlAmp: chs=1, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x07, nsteps=0x07, stepsize=0x0f, mute=0 Amp-Out vals: [0x00] Node 0x14 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Control: name="Capture Volume", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Control: name="Capture Switch", index=0, device=0 ControlAmp: chs=3, dir=In, idx=0, ofs=0 Device: name="CX20588 Analog", type="Audio", device=0 Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x50 0x50] [0x80 0x80] [0x80 0x80] [0x80 0x80] Converter: stream=4, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x15 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x16 [Audio Input] wcaps 0x100d1b: Stereo Amp-In R/L Amp-In caps: ofs=0x4a, nsteps=0x50, stepsize=0x03, mute=1 Amp-In vals: [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] [0x4a 0x4a] Converter: stream=0, channel=0 SDI-Select: 0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x1]: PCM Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x17* 0x18 0x23 0x24 Node 0x17 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Control: name="Mic Boost Volume", index=0, device=0 ControlAmp: chs=3, dir=Out, idx=0, ofs=0 Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x04 0x04] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a 0x1b* 0x1d 0x1e Node 0x18 [Audio Selector] wcaps 0x30050d: Stereo Amp-Out Amp-Out caps: ofs=0x00, nsteps=0x04, stepsize=0x27, mute=0 Amp-Out vals: [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 4 0x1a* 0x1b 0x1d 0x1e Node 0x19 [Pin Complex] wcaps 0x400581: Stereo Control: name="Headphone Jack", index=0, device=0 Pincap 0x0000001c: OUT HP Detect Pin Default 0x04214040: [Jack] HP Out at Ext Right Conn = 1/8, Color = Green DefAssociation = 0x4, Sequence = 0x0 Pin-ctls: 0xc0: OUT HP Unsolicited: tag=01, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1a [Pin Complex] wcaps 0x400481: Stereo Control: name="Internal Mic Phantom Jack", index=0, device=0 Pincap 0x00001324: IN Detect Vref caps: HIZ 50 80 Pin Default 0x90a70130: [Fixed] Mic at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0x3, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1b [Pin Complex] wcaps 0x400581: Stereo Control: name="Mic Jack", index=0, device=0 Pincap 0x00011334: IN OUT EAPD Detect Vref caps: HIZ 50 80 EAPD 0x0: Pin Default 0x04a19020: [Jack] Mic at Ext Right Conn = 1/8, Color = Pink DefAssociation = 0x2, Sequence = 0x0 Pin-ctls: 0x24: IN VREF_80 Unsolicited: tag=02, enabled=1 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1c [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00000014: OUT Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1d [Pin Complex] wcaps 0x400581: Stereo Pincap 0x00010034: IN OUT EAPD Detect EAPD 0x0: Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10* 0x11 Node 0x1e [Pin Complex] wcaps 0x400481: Stereo Pincap 0x00000024: IN Detect Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Control: name="Speaker Phantom Jack", index=0, device=0 Pincap 0x00000010: OUT Pin Default 0x92170110: [Fixed] Speaker at Int Front Conn = Analog, Color = Unknown DefAssociation = 0x1, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11* Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x12 Node 0x21 [Audio Output] wcaps 0x611: Stereo Digital Converter: stream=0, channel=0 Digital: Digital category: 0x0 IEC Coding Type: 0x0 PCM: rates [0x160]: 44100 48000 96000 bits [0xe]: 16 20 24 formats [0x5]: PCM AC3 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x22 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Unsolicited: tag=00, enabled=0 Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 1 0x21 Node 0x23 [Pin Complex] wcaps 0x40040b: Stereo Amp-In Amp-In caps: ofs=0x00, nsteps=0x04, stepsize=0x2f, mute=0 Amp-In vals: [0x00 0x00] Pincap 0x00000020: IN Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x00: Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Node 0x24 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In Amp-In caps: ofs=0x4a, nsteps=0x4a, stepsize=0x03, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Power states: D0 D1 D2 D3 D3cold EPSS Power: setting=D0, actual=D0 Connection: 2 0x10 0x11 Node 0x25 [Vendor Defined Widget] wcaps 0xf00000: Mono

  Read the article

• BSOD & System Failure after trying to install a new RAM

  - by Praveen Kumar

  I have updated the question with sections, so that people won't find it difficult to read. Basic System Information Let me give a basic introduction on my system. I have a system of following configuration: Processor: Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz 3.40GHz RAM: Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9) x 2 OS: Windows 7 Ultimate, SP1 Build 7601 HDD: 1 TB Seagate 7200 RPM The Problem It was working fine for about an year. Yesterday I planned to increase my RAM to 16 GB by putting another set of two Corsair Vengeance - 4GB Single Module DDR3 Memory Kit (CMZ4GX3M1A1600C9). I got it from an authorized reseller and also, the RAM was fitted by a service engineer only. After the RAM was fit (all the four), the system failed to start, with an error code of 0x000000f4. The complete information of it is: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 16393 Additional information about the problem: BCCode: f4 BCP1: 0000000000000003 BCP2: FFFFFA8008A39060 BCP3: FFFFFA8008A39340 BCP4: FFFFF800037C8510 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\093012-13041-01.dmp C:\Users\Praveen Kumar\AppData\Local\Temp\WER-30716-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt Another Problem We first thought that it was the RAM, which caused the issue. So I returned the RAMs and now my computer configuration is exactly how it was the previous day. But, following the removal of the RAM, I also had several crashes after that. One suspicious thing was with an error code c0000134: STOP: c0000135 The program can’t start because %hs is missing from your computer . Try resintalling the program to fix this problem. After reading contents from this, this and this, which were never my case, they didn't help me. But I didn't receive any more STOP c0000134 messages. But this 0x000000f4 keeps on coming. I am writing from the same system and it allows me to work for say, half an hour max. Then I hear a device disconnect sound, the one you hear in Windows 7, when a USB Mass Storage Device is plugged out. Immediately following that, my screen goes blank and I get 0x000000f4 blue screen. Okay, now I am really concerned about my Hard Disk data, but I have no clue if there is a problem with the HDD. My Question What all files do I need to submit for your reference? Can this issue be fixed? I am getting more time if I remove my RAM, clean it and then put it back. Weird! Hope I have given the necessary information to help you guys. Thanks in advance. Minidumps I have uploaded all the Minidump DMP files from C:\Windows\Minidump folder here: http://www.praveen-kumar.com/Minidumps.zip Let me know if you face any issues in accessing it. Will be able to share elsewhere. Updates 30-Sep-2012 10:15 AM IST: When I keep the system cover opened, pressed the HDD Cable well, it is allowing me to be on for about half an hour, I guess? Also, I feel that the CPU fan speed is kind of slow. It rotates at around 900 RPM, but the CPU Temperature is not more than 70° C. 30-Sep-2012 10:30 AM IST: My Modem (Beetel 220BX ADSL2+ Router) failed. I have no idea how it is related to this issue, but I thought that I need to document this too. I really have a bad day here. 30-Sep-2012 11:00 AM IST: System still running fine, with the cabinet cover open, now for about an hour. 30-Sep-2012 12:00 PM IST: I shut down the system and closed the cabinet. Started the system, and it hung after giving the password. After a few minutes, got the same 0x000000f4 error. So, while it is in the upright position, fixed the Hard Disk cable and now it is booting fine. Waiting for more observations and answers.

  Read the article

• Network Access: I can't access 192.168.1.101 from 192.168.1.102.

  - by takpar

  Hi, I'm running Ubuntu 10.04 on my PC with IP 192.168.1.101. every thing work fine, e.g. my web server is running and I can see http://localhost/ or http://192.168.1.101 properly. But the problem is that I cannot see my PC from my laptop at 192.168.1.102 e.g. at my laptop http://192.168.1.101 gives Connection timed out in browser. or trying to telnet on any port leads to: telnet: Unable to connect to remote host: Connection timed out laptop is running a fresh install of Ubuntu as well and there is no setup for firewall stuff in both computers. PS: Both computers can ping each other well. The router is a cicso linksys wireless ADSL modem. Currently, I can connect to FTP server on the Windows running on 192.168.1.102 from 192.168.1.101 without problem. Theses are commands ran on my PC, 192.168.1.101: ifconfig: adp@adp-desktop:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:e1:8e:cf inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::226:18ff:fee1:8ecf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1831935 errors:0 dropped:0 overruns:0 frame:0 TX packets:1493786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1996855925 (1.9 GB) TX bytes:215288238 (215.2 MB) Interrupt:27 Base address:0xa000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:951742 errors:0 dropped:0 overruns:0 frame:0 TX packets:951742 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:494351095 (494.3 MB) TX bytes:494351095 (494.3 MB) vmnet1 Link encap:Ethernet HWaddr 00:50:46:c0:00:01 inet addr:192.168.91.1 Bcast:192.168.91.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vmnet8 Link encap:Ethernet HWaddr 00:50:46:c0:00:08 inet addr:192.168.156.1 Bcast:192.168.156.255 Mask:255.255.255.0 inet6 addr: fe70::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) port 80 is set to 0.0.0.0 well: adp@adp-desktop:~$ netstat -ln | grep 'LISTEN ' tcp 0 0 127.0.0.1:52815 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4559 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:4369 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:7634 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5269 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:25 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5280 0.0.0.0:* LISTEN tcp 0 0 127.0.1.1:7777 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:33601 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:5222 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp6 0 0 :::139 :::* LISTEN tcp6 0 0 ::1:631 :::* LISTEN tcp6 0 0 :::445 :::* LISTEN /etc/hosts.deny is empty: adp@adp-desktop:~$ cat /etc/hosts.deny # /etc/hosts.deny: list of hosts that are _not_ allowed to access the system. # See the manual pages hosts_access(5) and hosts_options(5). # # Example: ALL: some.host.name, .some.domain # ALL EXCEPT in.fingerd: other.host.name, .other.domain # # If you're going to protect the portmapper use the name "portmap" for the # daemon name. Remember that you can only use the keyword "ALL" and IP # addresses (NOT host or domain names) for the portmapper, as well as for # rpc.mountd (the NFS mount daemon). See portmap(8) and rpc.mountd(8) # for further information. # # The PARANOID wildcard matches any host whose name does not match its # address. # # You may wish to enable this to ensure any programs that don't # validate looked up hostnames still leave understandable logs. In past # versions of Debian this has been the default. # ALL: PARANOID netstat -l: adp@adp-desktop:~$ netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:52815 *:* LISTEN tcp 0 0 *:hylafax *:* LISTEN tcp 0 0 *:www *:* LISTEN tcp 0 0 *:4369 *:* LISTEN tcp 0 0 localhost:7634 *:* LISTEN tcp 0 0 *:ftp *:* LISTEN tcp 0 0 *:xmpp-server *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 *:5280 *:* LISTEN tcp 0 0 adp-desktop:7777 *:* LISTEN tcp 0 0 *:33601 *:* LISTEN tcp 0 0 *:xmpp-client *:* LISTEN tcp 0 0 localhost:mysql *:* LISTEN tcp6 0 0 [::]:netbios-ssn [::]:* LISTEN tcp6 0 0 localhost:ipp [::]:* LISTEN tcp6 0 0 [::]:microsoft-ds [::]:* LISTEN udp 0 0 *:bootpc *:* udp 0 0 *:mdns *:* udp 0 0 *:47467 *:* udp 0 0 192.168.1.10:netbios-ns *:* udp 0 0 192.168.91.1:netbios-ns *:* udp 0 0 192.168.156.:netbios-ns *:* udp 0 0 *:netbios-ns *:* udp 0 0 192.168.1.1:netbios-dgm *:* udp 0 0 192.168.91.:netbios-dgm *:* udp 0 0 192.168.156:netbios-dgm *:* udp 0 0 *:netbios-dgm *:* raw 0 0 *:icmp *:* 7 netstat -rn: adp@adp-desktop:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.91.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet1 192.168.156.0 0.0.0.0 255.255.255.0 U 0 0 0 vmnet8 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 commands on the laptop, 192.168.1.102: ifconfig: root@fakeuser-laptop:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:33:a2:31:15 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:21 eth1 Link encap:Ethernet HWaddr 00:2d:d9:3e:1f:6c inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe70::21d:d9ff:fe3e:1f6c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5681 errors:0 dropped:0 overruns:0 frame:10313 TX packets:6717 errors:6 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4055251 (4.0 MB) TX bytes:779308 (779.3 KB) Interrupt:18 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:206 errors:0 dropped:0 overruns:0 frame:0 TX packets:206 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15172 (15.1 KB) TX bytes:15172 (15.1 KB) netstat -rn: root@fakeuser-laptop:~# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1

  Read the article

• PPTP VPN from Ubuntu cannot connect

  - by Andrea Polci

  I'm trying to configure under Linux (Kubuntu 9.10) a VPN I already use from Windows. I installed the network-manager-pptp package and added the VPN under Network Manager. These are the parameters under "advanced" button: Authentication Methods: PAP, CHAP, MSCHAP, MSCHAP2, EAP (I also tried "MSCHAP, MSCHAP2") Use MPPE Encryption: yes Crypto: Any Use stateful encryption: no Allow BSD compression: yes Allow Deflate compression: yes Allow TCP header compression: yes Send PPP echo packets: no When I try to connnect it doesn't work and this is what I get in the system log: 2010-04-08 13:53:47 pcelena NetworkManager <info> Starting VPN service 'org.freedesktop.NetworkManager.pptp'... 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN service 'org.freedesktop.NetworkManager.pptp' started (org.freedesktop.NetworkManager.pptp), PID 4931 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN service 'org.freedesktop.NetworkManager.pptp' just appeared, activating connections 2010-04-08 13:53:47 pcelena pppd[4932] Plugin /usr/lib/pppd/2.4.5//nm-pptp-pppd-plugin.so loaded. 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN plugin state changed: 3 2010-04-08 13:53:47 pcelena pppd[4932] pppd 2.4.5 started by root, uid 0 2010-04-08 13:53:47 pcelena NetworkManager <info> VPN connection 'MYVPN' (Connect) reply received. 2010-04-08 13:53:47 pcelena NetworkManager SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) 2010-04-08 13:53:47 pcelena NetworkManager SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. 2010-04-08 13:53:47 pcelena pppd[4932] Using interface ppp0 2010-04-08 13:53:47 pcelena pppd[4932] Connect: ppp0 <--> /dev/pts/2 2010-04-08 13:53:47 pcelena pptp[4934] nm-pptp-service-4931 log[main:pptp.c:314]: The synchronous pptp option is NOT activated 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. 2010-04-08 13:53:47 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 1, peer's call ID 14800). 2010-04-08 13:53:48 pcelena pppd[4932] CHAP authentication succeeded 2010-04-08 13:53:48 pcelena pppd[4932] CHAP authentication succeeded 2010-04-08 13:53:48 pcelena pppd[4932] LCP terminated by peer 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:929]: Call disconnect notification received (call id 14800) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_disp:pptp_ctrl.c:788]: Received Stop Control Connection Request. 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 4 'Stop-Control-Connection-Reply' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[callmgr_main:pptp_callmgr.c:258]: Closing connection (shutdown) 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' 2010-04-08 13:53:48 pcelena pptp[4927] nm-pptp-service-4918 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) 2010-04-08 13:53:48 pcelena pppd[4932] Modem hangup 2010-04-08 13:53:48 pcelena pppd[4932] Connection terminated. 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin failed: 1 2010-04-08 13:53:48 pcelena NetworkManager SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) 2010-04-08 13:53:48 pcelena pppd[4932] Exit. 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin failed: 1 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin state changed: 6 2010-04-08 13:53:48 pcelena NetworkManager <info> VPN plugin state change reason: 0 2010-04-08 13:53:48 pcelena NetworkManager <WARN> connection_state_changed(): Could not process the request because no VPN connection was active. 2010-04-08 13:53:48 pcelena NetworkManager <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS. 2010-04-08 13:54:01 pcelena NetworkManager <debug> [1270727641.001390] ensure_killed(): waiting for vpn service pid 4931 to exit 2010-04-08 13:54:01 pcelena NetworkManager <debug> [1270727641.001479] ensure_killed(): vpn service pid 4931 cleaned up The error that sticks out here is "pppd[4932] LCP terminated by peer". Does anyone has suggestion on what can be the problem and how to make it work?

  Read the article

< Previous Page | 41 42 43 44 45 46 47  | Next Page >