Search Results

Search found 7542 results on 302 pages for 'named routing'.

Page 45/302 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

  • Distributed development staff needing a common IP range

    - by bakasan
    I work on a development staff that is geographically distributed, mostly all throughout the state of CA, but several key members also must travel frequently. We rely quite heavily on a 3rd party provider API for a great deal of our subsystems (can't get into who it is or what they do). The 3rd party however is quite stringent on network access and have no notion of a development sandbox. Access is restricted to 2, 3 IP numbers and that's about it. Once we account for our production servers, that leaves us with an IP or two to spare for our dev team--which is still problematic as people's home IP changes, people travel, we have more than 2 devs, etc. Wide IP blocks are not permitted by the 3rd party. Nor will they allow dynamic DNS type services. There is no simple console to swap IPs on the fly either (e.g. if a dev's IP at home changes or they are on the road). As none of us are deep network experts, I'm wondering what our viable options are? Are there such things as 3rd party hosts to VPNs? Generally I think of a VPN as a mechanism to gain access to a home office, but the notion would be a 3rd party VPN that we'd all connect to and we'd register this as an IP origin w/ our 3rd party. We've considered using Amazon EC2 to effectively host a dev environment for each dev and using that to connect. Amazon only gives you so many static IPs however (I believe 5?) so this would only be a stop gap solution until our team size out strips our IP count at Amazon. Those were the only viable thoughts that I had, but again, I'm far from a networking guy. Tried searching for similar threads, but I'm not even sure I know the right vernacular to look around for.

    Read the article

  • Calculating and billing IP multicast usage on the Internet

    - by obvio171
    I've been searching for the reasons why IP multicast isn't widely supported on the Public Internet, and a commonly-cited reason is the difficulty ISPs have in tracking Multicast usage for later billing. Given this difficulty, since ISPs control the routers and they're not forced to support Multicast (as per IPv4), they just disable it. I couldn't find what this difficulty was though. Since an ISP has full control of any inbound and outbound traffic, be it Unicast or Multicast, what's the difficulty in tracking and billing the latter that does not exist in the former?

    Read the article

  • Setup VPN access on a windows dedicated server for browsing

    - by Pasta
    I have a dedicated windows server. I want to create a VPN to encrypt my traffic (browsing, IM, etc) as I browse on my laptop using public wifi networks. What keywords should I be using to search Google? Are there any resources that help me do this? Most of the solutions are just to encrypt communication between the server to a machine. It does not act like an internet gateway, etc.

    Read the article

  • linksys Rvo16 redundant link config

    - by Adeodatus
    Hi All I have been given an RVO16 to play with. I'm multihomed and I'd like to set it up so that my primary, highest bandwidth link receives all traffic and the other connection is a hot spare basically. I want them both online but only the primary 1 used until it goes down then all traffic should automatically failover to the secondary link. Those of you that have played on an RVO16, can I do this and if so, how? I imagine I'd have it act as a router and pad the route on one so that the other is never used unless the primary is down. How? Thanks all.

    Read the article

  • Should I use /etc/bind/zones/ or /var/cache/bind/?

    - by nbolton
    Each tutorial seems to have a different opinion on this. For my ISC BIND zones, should I use /etc/bind/zones/ or /var/cache/bind/? In the last install, I used /var/cache/bind/ but only because I was guided to do so; however I just spotted a pid file in there for this new Debian install, so I figured that using the "working directory" to store zone files probably wasn't the best idea. It seems that many admins use this so they don't have to type the full path when declaring a new zone. For example: file "/etc/bind/zones/db.foobar.com"; Instead of: file "db.foobar.com"; Is obviously easier to type, but is it good or bad practice? Some may also suggest setting the working directory to /etc/bind/zones: options { // directory "/var/cache/bind"; directory "/etc/bind/zones"; } ... but something tells me this isn't good practice, since the pid file would be created there I assume (unless it's just in /var/cache/bind by coincidence). I took a look at the manpage but it didn't seem to say what the directory option was for, any ideas exactly what it was design for?

    Read the article

  • Split horizon, route filtering, and having RIPv2 announce a non-attached route to host

    - by Paul
    Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

    Read the article

  • How to connect devices behind Comcast router/modem with devices behind wireless router

    - by deeperDATA
    I know this is going to seem like a simple solution but I have been unable to find a clear answer through Google. Simple office setup: I have a Comcast modem/router that has 4 hard wired ports. In one of those ports I have a Cisco wireless router which also has 4 of its own ports. What is the method for getting devices behind the modem/router to ping/communicate with devices behind the wireless router? They are all on the same subnet but the IP ranges differ. The router produces 192.168.1.1 by default while the Comcast modem/router produces 10.1.10.1 by default. I think what I'm attempting to do might be considered "extending" the modem/router's network but I'm not sure. Thank you in advance for your assistance.

    Read the article

  • Dual NIC internet access

    - by JavaRocky
    Q1. If a computer had two NICs, lets say windows, on which interface would HTTP traffic (or any for that matter) go out on. Not sure how the routes table would look like. Q2. If one of the NICs link becomes unresponsive, would traffic be automatically routed to the other NIC? Thanks.

    Read the article

  • Restrict VPN client traffic to certain domains/IP

    - by mr-euro
    Hi Is there any way to restrict a VPN client to only route certain traffic via the VPN and the rest via their local gateway? For example: traffic to a certain IP or domain gets routed across the VPN and all other requests do not. Let me know if you need more details. Thank you.

    Read the article

  • Multiple public IPs through DD-WRT without 1-to-1 NAT

    - by Stephen Touset
    I've done a search here and wasn't able to find anything relevant to my situation. I apologize in advance if I've missed an existing post on the topic. Our ISP has provided us with 6 static IP addresses. We are currently using two of them (plus one for the Comcast-provided router). One of the static addresses routes to our internal network, and the other goes to our VOIP phone system. Unfortunately, the Comcast machine doesn't support QoS, so our VOIP calls have been choppy. We plan to put the Comcast-provided router into bridge mode and replace it with an ASUS RT-N16 running DD-WRT. However, I'm unsure how to set up DD-WRT to function similarly to our existing Comcast router. The Comcast router's WAN IP is the first of our static IP addresses. We did not need to provide an internal LAN IP address — simply connecting machines that use our other public addresses to the LAN ports on the Comcast router is enough for it to route between the connected machines and our internet connection. Is there a way to do a similar setup through the DD-WRT? Thanks in advance.

    Read the article

  • Cisco ASA 5505 site to site IPSEC VPN won't route from multiple LANs

    - by franklundy
    Hi I've set up a standard site to site VPN between 2 ASA 5505s (using the wizard in ASDM) and have the VPN working fine for traffic between Site A and Site B on the directly connected LANs. But this VPN is actually to be used for data originating on LAN subnets that are one hop away from the directly connected LANs. So actually there is another router connected to each ASA (LAN side) that then route to two completely different LAN ranges, where the clients and servers reside. At the moment, any traffic that gets to the ASA that has not originated from the directly connected LAN gets sent straight to the default gateway, and not through the VPN. I've tried adding the additional subnets to the "Protected Networks" on the VPN, but that has no effect. I have also tried adding a static route to each ASA trying to point the traffic to the other side, but again this hasn't worked. Here is the config for one of the sites. This works for traffic to/from the 192.168.144.x subnets perfectly. What I need is to be able to route traffic from 10.1.0.0/24 to 10.2.0.0/24 for example. ASA Version 8.0(3) ! hostname Site1 enable password ** encrypted names name 192.168.144.4 Site2 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.144.2 255.255.255.252 ! interface Vlan2 nameif outside security-level 0 ip address 10.78.254.70 255.255.255.252 (this is a private WAN circuit) ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passwd ** encrypted ftp mode passive access-list inside_access_in extended permit ip any any access-list outside_access_in extended permit icmp any any echo-reply access-list outside_1_cryptomap extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 access-list inside_nat0_outbound extended permit ip 192.168.144.0 255.255.255.252 Site2 255.255.255.252 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-603.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 access-group inside_access_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 10.78.254.69 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute dynamic-access-policy-record DfltAccessPolicy aaa authentication ssh console LOCAL http server enable http 0.0.0.0 0.0.0.0 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs crypto map outside_map 1 set peer 10.78.254.66 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal telnet timeout 5 ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside threat-detection basic-threat threat-detection statistics port threat-detection statistics protocol threat-detection statistics access-list group-policy DfltGrpPolicy attributes vpn-idle-timeout none username enadmin password * encrypted privilege 15 tunnel-group 10.78.254.66 type ipsec-l2l tunnel-group 10.78.254.66 ipsec-attributes pre-shared-key * ! ! prompt hostname context

    Read the article

  • Passing OpenVPN road-warrior traffic through tunnel pfsense

    - by Chris
    I have a local LAN (10.100.100.0/24) and OpenVPN road-warriors (10.99.99.0/24). pfSense is regulating all this as follows: LAN: 10.100.100.105 WAN: 10.100.99.1 (connected to DSL Router which connects to internet). OPT1: 10.99.99.0 (OpenVPN tun0). There is an IPSec connection between my office and another office where my LAN can work on a specific IP address (sql server to be exact) on 192.168.30.41. My problem is that I wish my OpenVPN road-warrior clients to be able to use the IPSec service on 192.168.30.41 as well (which at present they cannot despite the fact that I am pushing the route 192.168.30.0 255.255.255.0). The other site's administrator cannot add the extra route for my openvpn clients for a lot of reasons which I am not going to enter at this stage. Is there a possibility that I could NAT all of my openVPN road-warriors requests through a local LAN IP address (something like 10.100.100.250 which is not used by anything on my LAN). The problem is that I am a newbie with pfSense so as much step-by-step help as possible would be very much appreciated! Thank you. C.

    Read the article

  • Access internal IP using public IP

    - by willvv
    Hi, I have a DSL modem with a public IP address (201.206.x.x), and I have a web server in my internal network (192.168.0.50). I set up the modem to forward requests to port 80 to my web server, so, if I access 201.206.x.x from outside my network, it shows my web page, the same happens if I access 192.168.0.50 from a computer inside my network. Now, the problem is when I try to access 201.206.x.x from my internal network, the browser tries to connect to the DSL modem configuration, instead of redirecting my request to my Web server. Which settings do I have to change in the modem to set up this redirection? Thanks!

    Read the article

  • Ping only works after about 30 seconds

    - by Ricardo Polo
    Today I am working on this issue and I would love your ideas. There is a network with something like this LAN 1 -- WAN CHANNEL--- LAN 2 The LAN 1 have two segments. When I make a ping from LAN 1 segment 1 it works like a charm. When I make a ping from LAN 1 segment 2 I have no ping, but after about 30 seconds of continues ping (ping -t) it start to work perfect. After some time of no activity with the destination host the issue happens again. Tracing the route packets stops in the last router before the target. This is the first router in LAN 2 after the WAN channel. In the next screenshot you can see thie issue, the first ping is before a continuos ping and the second one is while continous ping is running. Thank you in advance

    Read the article

  • Forward differing hostnames to different internal IPs through NAT router

    - by abrereton
    Hi, I have one public IP address, one router and multiple servers behind the router. I would like to forward differing domains (All using HTTP) through the router to different servers. For example: example1.com => 192.168.0.110 example2.com => 192.168.0.120 foo.example2.com => 192.168.0.130 bar.example2.com => 192.168.0.140 I understand that this could be accomplished using Port Forwarding, but I need all hosts running on port 80. I found some information about IP Masquerading, but I found this difficult to understand, and I am not sure if it is what I am after. Another solution I have found is to direct all traffic to Reverse Proxy server, which forwards the requests onto the appropriate server. What about iptables? I am using a Billion 7404 VNPX router. Is there a feature that this router has that can accomplish this? Are these my only options? Have I missed something completely? Is one recommended over the others? I have searched around but I don't think I am hitting the correct keywords. Thanks in advance.

    Read the article

  • Fritz!Box IPv6-Address different than IPv6-Prefix

    - by kmindi
    In my Fritzbox it states the following: IPv6-Adresse: 2a02:8070:600::14b6:c7******, Gültigkeit: 100465/86065s IPv6-Präfix: 2a02:8070:62c:3200::/56, Gültigkeit: 100464/86064s I am not able to connect to IPv6 Addresses from computers configured by the fritzbox, because they get an address with prefix 2a02:8070:62c:3200::/56 but somehow the fritzbox does not route those addresses. Is this because the IPv6-Address is not in the prefix range? The address of the Fritzbox responds to pings, but my computers reached via various addresses from the prefix range do not (: PING 2a02:8070:62c:3200:28d****(2a02:8070:62c:3200:28d****) 32 data bytes From 2a02:8070:600:0:14b6*** icmp_seq=0 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=1 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=2 Destination unreachable: Administratively prohibited From 2a02:8070:600:0:14b6*** icmp_seq=3 Destination unreachable: Administratively prohibited blocked ping this is "view" from outside From inside the ping6 looks like this: traceroute -6 heise.de traceroute to heise.de (2a02:2e0:3fe:100::8), 30 hops max, 80 byte packets 1 fritz.box (2a02:8070:62c:3200:****) 0.787 ms 1.424 ms 1.702 ms 2 * * * ...... 30 * * *

    Read the article

  • Can fragments of a packet be refragmented again?

    - by gsinha
    In IPv4, fragmentation is done by routers on way to the destination if DF(do not fragment) flag is not set in the IP packet. Once a packet is fragmented, its fragments may take different paths (due to various reasons like topology changes) to the destination. If, on some link again in the path to destination, one routers find that the link MTU is smaller than the frame size, then either the packet needs to be fragmented or dropped. Can fragments of a packet be refragmented again? If yes, what will be the value of MF flag in the new individual fragments created by this?

    Read the article

  • How to force certain traffic through GRE tunnel?

    - by wew
    Here's what I do. Server (public internet is 222.x.x.x): echo 'net.ipv4.ip_forward=1' >> /etc/sysctl.conf sysctl -p iptunnel add gre1 mode gre local 222.x.x.x remote 115.x.x.x ttl 255 ip add add 192.168.168.1/30 dev gre1 ip link set gre1 up iptables -t nat -A POSTROUTING -s 192.168.168.0/30 -j SNAT --to-source 222.x.x.x iptables -t nat -A PREROUTING -d 222.x.x.x -j DNAT --to-destination 192.168.168.2 Client (public internet is 115.x.x.x): iptunnel add gre1 mode gre local 115.x.x.x remote 222.x.x.x ttl 255 ip add add 192.168.168.2/30 dev gre1 ip link set gre1 up echo '100 tunnel' >> /etc/iproute2/rt_tables ip rule add from 192.168.168.0/30 table tunnel ip route add default via 192.168.168.1 table tunnel Until here, all seems going right. But then 1st question, how to use GRE tunnel as a default route? Client computer is still using 115.x.x.x interface as default. 2nd question, how to force only ICMP traffic to go through tunnel, and everything else go default interface? I try doing this in client computer: ip rule add fwmark 200 table tunnel iptables -t mangle -A OUTPUT -p udp -j MARK --set-mark 200 But after doing this, my ping program will timeout (if I not doing 2 command above, and using ping -I gre1 ip instead, it will works). Later I want to do something else also, like only UDP port 53 through tunnel, etc. 3rd question, in client computer, I force one mysql program to listen on gre1 interface 192.168.168.2. In client computer, there's also one more public interface (IP 114.x.x.x)... How to forward traffic properly using iptables and route so mysql also respond a request coming from this 114.x.x.x public interface?

    Read the article

  • Using Static Public IPs and Private DHCP IPs on the Same Router

    - by Andrew Larsson
    I have a subnet of public IP addresses that my ISP has provided me with. They are routed through my router (how profound) that has a a static IP. I have successfully assigned the IPs from that subnet to various devices on my network. This works just fine, they get their own public IP, they can access the Internet, and the Internet can access them. However, I would like to also assign some private IPs on my network through that same router and put them behind NAT. Is this even possible? Could a VLAN be of use? I would like to avoid putting another router on the network, which makes this is quite an awkward question.

    Read the article

  • redirect from mysite.com to www.mysite.com

    - by jml
    hi there, i know that this has been answered many many times, so if someone wants to point me to another thread that answers my question specifically, that is fine... for right now, my searches aren't yielding many results. so i have a website like mysite.com that has a flash swf embedded in it and i go to www.mysite.com ... all of the sudden, things don't work properly. i would like to get to the bottom of this, because it's not like the page just "doesn't load" at all; it loads and i can only do certain things; as if certain functionality is disabled (might be url requests for specific urls etc). do i need to manage this in my control panel? i wouldn't assume so, because the site loads; just has a crippled functionality from within the swf. i was thinking it might have more to do with my crossdomain.xml file; could this be the case? thanks for any tips or suggestions.

    Read the article

  • DNS and mod_rewrite not-collaborating

    - by ???? ?????????
    Hello, I have added a CNAME record to my DNS on my CentOS server to redirect subdomain.mydomain.com to another server. I also use mod_rewrite to rewrite mydomain.com to www.mydomain.com: RewriteEngine on RewriteCond %{HTTP_HOST} ^mydomain\.com$ [NC] RewriteRule ^(.*)$ http://www.mydomain.com/$1 [L,R=301] this is placed into .htaccess in the root public html directory Now, the problem is that whenever I lookup subdomain.mydomain.com it redirects me to www.mydomain.com I tried adding another RewriteCond: RewriteEngine on RewriteCond %{HTTP_HOST} ^mydomain\.com$ [NC] RewriteCond %{HTTP_HOST} !^subdomain\.mydomain\.com$ [NC] RewriteRule ^(.*)$ http://www.mydomain.com/$1 [L,R=301] But it didn't help... Anyone has some ideas?

    Read the article

  • How to redirect all Internet traffic to OpenVPN Server

    - by JuliaS
    I have seen working solutions around the issue of forcing Internet traffic to go through the OpenVPN server but they are all done in Linux, all I want to know is how to add an entry to the route table in windows to make this happen. connectivity between the client and server is fine, my Windows 7 client can establish a connection to the Windows 2008 Server, but when established Internet traffic is still going from the local Windows 7 machine. Here are the details: Server: Windows 2008 Server with one NIC OpenVPN IP Address: 192.168.0.1 Local NIC IP Address (connects the server to the Internet): 10.242.69.107 Client: Windows 7 with one NIC OpenVPN IP Address: 192.168.0.2 ISP allocated IP Address: 10.0.8.2 (gateway 10.0.8.1) Server OpenVPN Config: dev tun ifconfig 192.168.0.1 192.168.0.2 secret static.key push "redirect-gateway def1" Client OpenVPN Config: remote xxx.xxx.com dev tun ifconfig 192.168.0.2 192.168.0.1 secret static.key I'm not an expert with adding routes...etc. I would be grateful if someone could let me know how to add this entry in my server/client route table. EDIT: Output from the client's netstat -rnv IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.8.1 10.0.8.2 20 10.0.8.0 255.255.255.252 On-link 10.0.8.2 276 10.0.8.2 255.255.255.255 On-link 10.0.8.2 276 10.0.8.3 255.255.255.255 On-link 10.0.8.2 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.252 On-link 192.168.0.2 286 192.168.0.2 255.255.255.255 On-link 192.168.0.2 286 192.168.0.3 255.255.255.255 On-link 192.168.0.2 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.8.2 276 224.0.0.0 240.0.0.0 On-link 192.168.0.2 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.8.2 276 255.255.255.255 255.255.255.255 On-link 192.168.0.2 286 ===========================================================================

    Read the article

  • Connecting together DIR-615 and DIR-655

    - by ra170
    On my DIR-655 my internal network is: 192.168.0.x On my DIR-615 my internal network is: 192.168.1.x They are both connected to my firewall PIX 501 box The PIX itself is connected to the comcast modem. I briefly looked at the menu options on those router and they look similar, however I'm not sure what's the best way to connect those two together so that I can go between those networks. (printing, file browsing, etc.) I'm not sure if I have to do this somehow on those two router or on the PIX itself, or probably on all of them. If anyone has experience with something like that please let me know..

    Read the article

  • DrayTek Vigor 2920(n): VPN with VLAN restrictions?

    - by Dirk
    Hi, I'm currently installing a DrayTek Vigor 2920n router in a new office. This router is to be used for 2 seperate companies. For one of these companies, the router has a LAN-2-LAN (VPN) connection to a datacenter configured. The other company should not be able to access this other (VPN-)network. I'm aware of the capability of this router to have VLAN's, but I cannot figure out how to configure the VPN-connection to only be accessible for VLAN0 and not for VLAN1. I know I can also add another router to physically split both networks, but we bought the DrayTek with the idea that it could easily have the VPN-connection available for VLAN0 and not for VLAN1. VLAN1 can easily be in another subnet, that's fine, although, I don't know how to configure that on this DrayTek. Can anyone point me in the right direction? Thanks in advance, Dirk

    Read the article

  • How can I prevent OpenVPN from clobbering local route?

    - by ataylor
    I have a local network on 192.168.1.0 with netmask 255.255.255.0. When I connect to a VPN though OpenVPN (as a client), it pushes a route for 192.168.1.0 that clobbers the existing one, making my local network inaccessible. I don't to access anything on 192.168.1.0 on the remote machine; I'd like to just ignore it, while accepting the other routes that are pushed. My client is Ubuntu 10.10. How can I skip the one offending route?

    Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >