Search Results

Search found 17076 results on 684 pages for 'nightly build'.

Page 45/684 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

• Windows 7 x64 installation freezes on new PC build

  - by jhsowter

  Symptoms While attempting to install Windows 7 (64 bit) on my new PC build, it freezes usually at the point where it is expanding the windows image, but has frozen as early as accepting the licence agreement, and as late as just after the first restart. My specs are at the bottom of the post. So far I have tried the following to identify the problem, in rough chronological order: Tried different hard drives with different sata cables. Same symptoms. I later used a different computer to install windows on the same hard drive with no problems. Tried the RAM in different slots, and tried one RAM stick instead of two. Same symptoms. Updated the BIOS to 1.60. Same symptoms. Ran Memtest86+ with RAM in dual channel. It passed about 6 times when I left it running overnight. Used USB to install windows instead of an optical drive. Same symptoms. Change SATA configuration from AHCI to IDE. Same symptoms. Tried various different SATA ports. Same symptoms. Updated BIOS to 1.70. Same symptoms. I saw the RAM did not list my motherboard as being supported even though the motherboard did list the RAM as being supported. So I tried some Kingston DDR3 1333MHz RAM instead. Same symptoms. Other (possibly) pertinent information My CPU idles at about 30 °C. I can't tell what it gets to when it's working. When I installed the CPU, the lever which locks the CPU in place took quite a bit of force to pull down. Now I didn't just yank it down without rechecking the CPU was seated properly about 5 times, but it does seems unusual, and I wonder if the CPU was seated badly if I would see these symptoms? I am out of ideas and don't know how to diagnose any further. I suppose either the motherboard or CPU must be the problem. I am on the verge of taking it to a specialist. The Question How should I proceed from here? Is there anything I can rule out as being the source of the symptoms I am seeing? My Specs CPU: Intel i5 3570k RAM: G.Skill RipjawsX 8GB kit HDD: single 3.5" 500GB SATA or 160GB 2.5" SATA (at different times and sometime together. But no RAID or anything). MB: ASRock Extreme4 Z77 PSU: Silverstone Strider Plus 600W ST60F-P

  Read the article

• Nvidia drivers don't work with mainline kernel

  - by dutchie

  I want to try some of the new features in the btrfs filesystem, and to do that I need to use a newer kernel than is included in Ubuntu 12.04. To do that, I have installed linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb, linux-headers-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb, and linux-image-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb from the mainline kernel download here. However, on rebooting into the 3.4 kernel, my desktop is stuck at a very low resolution and I cannot increase it to the full. This did happen when I first installed, but a simple install of the nvidia-current package got everything working nicely with my GTX570 card. There were appear to be some DKMS errors when I installed the kernel, and they indicated I should look at /var/lib/dkms/nvidia-current/295.40/build/make.log: josh@sirius:~/Downloads$ sudo dpkg -i linux-*.deb Selecting previously unselected package linux-headers-3.4.0-030400. (Reading database ... 309400 files and directories currently installed.) Unpacking linux-headers-3.4.0-030400 (from linux-headers-3.4.0-030400_3.4.0-030400.201205210521_all.deb) ... Selecting previously unselected package linux-headers-3.4.0-030400-generic. Unpacking linux-headers-3.4.0-030400-generic (from linux-headers-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb) ... Selecting previously unselected package linux-image-3.4.0-030400-generic. Unpacking linux-image-3.4.0-030400-generic (from linux-image-3.4.0-030400-generic_3.4.0-030400.201205210521_amd64.deb) ... Done. Setting up linux-headers-3.4.0-030400 (3.4.0-030400.201205210521) ... Setting up linux-headers-3.4.0-030400-generic (3.4.0-030400.201205210521) ... Examining /etc/kernel/header_postinst.d. run-parts: executing /etc/kernel/header_postinst.d/dkms 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic ERROR (dkms apport): kernel package linux-headers-3.4.0-030400-generic is not supported Error! Bad return status for module build on kernel: 3.4.0-030400-generic (x86_64) Consult /var/lib/dkms/nvidia-current/295.40/build/make.log for more information. Setting up linux-image-3.4.0-030400-generic (3.4.0-030400.201205210521) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic ERROR (dkms apport): kernel package linux-headers-3.4.0-030400-generic is not supported Error! Bad return status for module build on kernel: 3.4.0-030400-generic (x86_64) Consult /var/lib/dkms/nvidia-current/295.40/build/make.log for more information. run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic update-initramfs: Generating /boot/initrd.img-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.4.0-030400-generic /boot/vmlinuz-3.4.0-030400-generic Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.4.0-030400-generic Found initrd image: /boot/initrd.img-3.4.0-030400-generic Found linux image: /boot/vmlinuz-3.2.0-24-generic Found initrd image: /boot/initrd.img-3.2.0-24-generic Found memtest86+ image: /memtest86+.bin Found Ubuntu 12.04 LTS (12.04) on /dev/sda1 Found Windows 7 (loader) on /dev/sda2 Found Windows 7 (loader) on /dev/sda3 done /var/lib/dkms/nvidia-current/295.40/build/make.log: DKMS make.log for nvidia-current-295.40 for kernel 3.4.0-030400-generic (x86_64) Thu Jun 7 00:58:39 BST 2012 NVIDIA: calling KBUILD... test -e include/generated/autoconf.h -a -e include/config/auto.conf || ( \ echo; \ echo " ERROR: Kernel configuration is invalid."; \ echo " include/generated/autoconf.h or include/config/auto.conf are missing.";\ echo " Run 'make oldconfig && make prepare' on kernel src to fix it."; \ echo; \ /bin/false) mkdir -p /var/lib/dkms/nvidia-current/295.40/build/.tmp_versions ; rm -f /var/lib/dkms/nvidia-current/295.40/build/.tmp_versions/* make -f scripts/Makefile.build obj=/var/lib/dkms/nvidia-current/295.40/build cc -Wp,-MD,/var/lib/dkms/nvidia-current/295.40/build/.nv.o.d -nostdinc -isystem /usr/lib/gcc/x86_64-linux-gnu/4.6/include -I/usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include -Iarch/x86/include/generated -Iinclude -include /usr/src/linux-headers-3.4.0-030400-generic/include/linux/kconfig.h -D__KERNEL__ -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implicit-function-declaration -Wno-format-security -fno-delete-null-pointer-checks -O2 -m64 -mtune=generic -mno-red-zone -mcmodel=kernel -funit-at-a-time -maccumulate-outgoing-args -fstack-protector -DCONFIG_AS_CFI=1 -DCONFIG_AS_CFI_SIGNAL_FRAME=1 -DCONFIG_AS_CFI_SECTIONS=1 -DCONFIG_AS_FXSAVEQ=1 -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -mno-sse2 -mno-3dnow -mno-avx -Wframe-larger-than=1024 -Wno-unused-but-set-variable -fno-omit-frame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-statement -Wno-pointer-sign -fno-strict-overflow -fconserve-stack -DCC_HAVE_ASM_GOTO -I/var/lib/dkms/nvidia-current/295.40/build -Wall -MD -Wsign-compare -Wno-cast-qual -Wno-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"295.40\" -Wno-unused-function -Wuninitialized -mno-red-zone -mcmodel=kernel -UDEBUG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(nv)" -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o /var/lib/dkms/nvidia-current/295.40/build/.tmp_nv.o /var/lib/dkms/nvidia-current/295.40/build/nv.c In file included from include/linux/kernel.h:19:0, from include/linux/sched.h:55, from include/linux/utsname.h:35, from /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:38, from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13: include/linux/bitops.h: In function ‘hweight_long’: include/linux/bitops.h:66:41: warning: signed and unsigned type in conditional expression [-Wsign-compare] In file included from /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess.h:577:0, from include/linux/poll.h:14, from /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:97, from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13: /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess_64.h: In function ‘copy_from_user’: /usr/src/linux-headers-3.4.0-030400-generic/arch/x86/include/asm/uaccess_64.h:53:6: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] In file included from /var/lib/dkms/nvidia-current/295.40/build/nv.c:13:0: /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h: At top level: /var/lib/dkms/nvidia-current/295.40/build/nv-linux.h:114:75: fatal error: asm/system.h: No such file or directory compilation terminated. make[3]: *** [/var/lib/dkms/nvidia-current/295.40/build/nv.o] Error 1 make[2]: *** [_module_/var/lib/dkms/nvidia-current/295.40/build] Error 2 NVIDIA: left KBUILD. nvidia.ko failed to build! make[1]: *** [module] Error 1 make: *** [module] Error 2

  Read the article

• Why to build own CMS?

  - by ile

  On my first job interview, I was asked why did I build my own CMS? Why not to use one of existing CMS, Wordpress, Joomla, Drupal...? At first, I was stunned. I couldn't immediately recall all of my reasons for building my own CMS, but this was definitely one of the main reasons: It's my code and if I want to change something in that CMS (which I often have to do, because each website I build needs CMS with different functions) it's not a big problem. For some time I've been using Wordpress and one of the main things that distracted me from using it was discovering bugs in code that wasn't written by me and this bugs were often, especially if I made some changes to CMS or added a plugin... Here, I can find these 8 reasons why NOT to build own CMS: It won’t meet users’ needs It’s too much work It won’t be a standard solution It won’t be extendible fast enough It won’t be tested well enough It won’t be easily changeable It won’t add any value Create content, not functionality Quote from the same page: So the main question to ask yourself is: ‘Why am I really trying to re-solve a problem that has already been solved before?’ Well, I definitely agree that it's hard to invent CMS that hasn't been already invented, but on other hand, I think every CMS is (or should be) individual... it maybe won't have a million of functions, it will have 3 functions but their usage will be clear (to a user) and do all that one site needs to have. I think also that it is not good to give to a client a CMS with a lot of functions that are never used and it looks probably more professional when website and CMS together look like one product. I would also like to comment some quote parts: "It’s too much work" - I agree, but when using existing CMS and customizing it to website needs and can sometimes be very hard job or mission impossible. "It won’t be easily changeable" - I disagree with this one. What is your opinion on this one, why did you develop or didn't develop your own CMS? Ile

  Read the article

• VISUAL STUDIO 2008 SETUP PROJECT MSI BUILD with Bootstrapping for quite installation

  - by rajadiga

  I build Visual Studio 2008 setup Project with MSI build it depends on .NET 3.5. I added Prerequisites like: .NET 3.5, Microsoft office interoperability, VS tools for office System 3.0 Run time, .etc. After that Selected "Download Prerequisite from Same location as my application" in Specify install location for Prerequisite. Build the setup. I can find mysetup.msi in Release directory. In new Machine I started fresh installation of my application... While Clicking the mySetup.msi. Dialog shows like this " This Setup Requires .NET framework 3.5 , Please install .NET setup then run this setup, .NET Framework can be obtained from web Do you want to do that now?" it gives "yes" no option - if I press YES it goes microsoft website. How can avoid it ? I wanted setup take .NET Framework to be installed from same location where I put all setup files including mysetup.msi ? In case of Quite installation cmd /c "msiexec /package mysetup.msi /quiet /log install.log" ..in log I can see only half way through installtion then error Property(S): HideFatalErrorForm = TRUE MSI (s) (D0:24) [00:07:08:015]: Product: my product-- Installation failed. === Logging stopped: 3/23/2010 0:07:08 === so how can complete the installation without user intervention and without error using VS2008 setup project thanks for all the help in advance for any input.

  Read the article

• Unhandled Exception with c++ app on Visual Studio 2008 release build - occurs when returning from fu

  - by Rich

  Hi, I have a (rather large) application that I have written in C++ and until recently it has been running fine outside of visual studio from the release build. However, now, whenever I run it it says "Unhandled exception at 0x77cf205b in myprog.exe: 0xC0000005: Access violation writing location 0x45000200.", and leads me to "crtexe.c" at line 582 ("mainret = main(argc, argv, envp);") if I attempt to debug it. Note that this problem never shows if I run my debug executable outside of visual studio, or if I run my debug or release build within visual studio. It only happens when running the release build outside of visual studio. I have been through and put plenty of printfs and a couple of while(1)s in it to see when it actually crashed, and found that the access violation occurs at exactly the point that the value is returned from the function (I'm returning a pointer to an object). I don't fully understand why I would get an access violation at the point it returns, and it doesn't seem to matter what I'm returning as it still occurs when I return 0. The point it started crashing was when I added a function which does a lot of reading from a file using ifstream. I am opening the stream every time I attempt to read a new file and close it when I finish reading it. If I keep attempting to run it, it will run once in about 20 tries. It seems a lot more reliable if I run it off my pen drive (it seems to crash the first 3 or 4 times then run fine after that - maybe it's due to its slower read speed). Thanks for your help, and if I've missed anything let me know.

  Read the article

• How do I build latest Tycho

  - by hedefalk

  I've tried to build Tycho now for a couple of hours and just can't get it to work. I've followed these instructions: https://docs.sonatype.org/display/TYCHO/BuildingTycho So, I've downloaded Eclipse 3.6RC2 and Delta-packs linked from this instruction (is it for 3.5 only?): http:// (remove space) aniefer.blogspot.com/2009/06/using-deltapack-in-eclipse-35.html I've added the DeltaPack to the TargetPlatform inside of the Eclipse-installation. I've installed Maven: Apache Maven 3.0-beta-1 (r935667; 2010-04-19 19:00:39+0200) I can run the first bootstrap of the build, but the second fails: mvn clean install -e -V -Pbootstrap-2 -Dtycho.targetPlatform=$TYCHO_TARGET_PLATFORM ERROR] Internal error: java.lang.RuntimeException: Could not resolve plugin org.eclipse.core.net.linux.x86_null -> [Help 1] I've tried different stuff, I built an older revision against 3.5 as in this blogpost: http:// (remove space) divby0.blogspot.com/2010/03/im-in-love-with-tycho-08-and-maven-3.html and that actually built a running maven, but that version then can't find the tycho plugin: org.apache.maven.plugin.version.PluginVersionResolutionException: Error resolving version for plugin 'org.codehaus.tycho:maven-tycho-plugin' from the repositories [local (/Users/viktor/.m2/repository), central (http://repo1.maven.org/maven2)]: Plugin not found in any plugin repository I thought that the point was that the plugin was going to build in when I had built a Tycho-dist…? Sorry about the links, stackoverflows spam-protection doesn't let me post more than url yet

  Read the article

• How to build a ~500 page Flash site

  - by philwilks

  I am about to embark on building a Flash site with approximately 500 pages. The site is an interactive learning type of system, with about 10 "chapters" each containing around 50 "pages". Each page has some sort of animation and interactivity, for example the user might have to decide whether a statement is true or false by clicking on one of two buttons, and then an appropriate response is displayed. The user can jump backwards and forwards between pages as they wish. As far as I know, these are some of my options... A) Build the entire site as a single Flash file with no external content. B) Build each of the 10 chapters as a separate Flash file, and then have a master Flash file which loads in the chapters. Each page would then be a separate movie clip within the chapter file. C) Build each indevidual page as a separate Flash file, and then have master Flash file which loads these in. At the moment I'm thinking that option B would be best, and I'd be very grateful for your thoughts on this! Of course, there are probably other options that I haven't thought of.

  Read the article

• TFS Solution build cascading to several other builds even when common components were not modified

  - by Bob Palmer

  Hey all, here is the issue I am currently trying to work through. We are using Team Foundation Server 2008, and utilizing the automated build support out of the box. We have one very large project that encompasses a number of interrelated components and web sites, each of which is set up as a Visual Studio solution file. Many of these solutions are highly interrelated since they may contain applications, or contain common libraries or shared components. We have roughly 20 or so applications, three large web sites, and about 20 components. Each solution may include projects from other solutions. For example, a solution for a console app would also include the project files for all of the components it utilizes, since we need to ensure that when someone changes a component and rebuilds it, it is reflected in all of the projects that consume that component, and we can make sure nothing was broken. We have build projects for each solution, whether that's an application, component, or web site. For this example, we will call them solutions 01, 02, and 03. These reference multiple projects (both their own core project and test projects, plus the projects relating to various components). Solution 01 has projects A, B, and C. Solution 02 has projects C, D, and E. Solution 03 has projects E, F, and G. Now, for the problem. If I modify project A, the system will end up rebuilding all three solutions. Worse, all thirty solutions reference common projects used for data access (let's call it project H). Because they all share one project in common, if I modify any solution in my stack, even if it does not touch project H, I still end up kicking off every single build script. Any thoughts on how to address this? Ideally I would only want to kick off builds where their constituant projects were directly modified - i.e in the example below, if I modified project C, I would only rebuild solutions 01 and 02. Thanks!

  Read the article

• Control pdb file output from build defintion file

  - by Urvi

  Hello, I am trying to generate a release build with no pdb files generated. I have seen numerous posts that suggest right-clicking on the project, selecting Properties, going to the Build tab and then to the Advanced... butoon and changing Debug Info to none. This works and all, but I need to do this for a build of ~50 solutions which contain ~25 projects each! Other posts mention editing the appropriate .csproj file, but again, with so many projects, this would take a long time. Is there any way to achieve this via the TFSBuild.proj file? I have tried adding the following to the TFSBuild.proj file, with no luck. <PropertyGroup> <Configuration>Release</Configuration> <Platform>AnyCPU</Platform> </PropertyGroup> <PropertyGroup> <DebugSymbols>false</DebugSymbols> <DebugType>none</DebugType> <Optimize>true</Optimize> </PropertyGroup> The following line prints out Release|AnyCPU, none, and false, but I still see .pdb file in the $(OutputDir) folder. <Message Text="$Configuration|Platform): $(Configuration)|$(Platform)" /> <Message Text="DebugType is: $(DebugType)"/> <Message Text="DebugSymbols is: $(DebugSymbols)"/> Thanks in advance, Urvi

  Read the article

• Eclipse CDT setup for remote build

  - by Posco Grubb

  Is there a better way to setup Eclipse CDT for local editing and remote building? I am working on a C++ project that uses GNU make in Linux. The code is under CVS on a Linux server. When I'm in the lab, I use Eclipse CDT on a Linux-x64 PC. The project is built on a Linux-x86 PC. All the computers in the lab (including the CVS server) have NFS mounts. When I'm at home, I use Eclipse CDT on a Windows 7 PC. The Windows PC connects to the Linux CVS server via SSH tunnel. To edit source, I rsync the C++ project under the Linux Eclipse workspace back to my Windows Eclipse workspace. (I can also do a remote CVS checkout on the Windows PC.) To build from home, I use a custom build command that SSH's to the Linux-x86 PC, rsync's the C++ project from my Windows Eclipse workspace to my Linux Eclipse workspace, and then runs make on the Liunx-x86 PC, specifying the correct path for the Makefile. In order to go back and forth between lab and home without committing my changes to CVS every time, I use rsync. When I transition from lab to home, I rsync sources to my Windows Eclipse workspace. When I build from home, the sources get rsync'd back to the Linux Eclipse workspace. Is there a better, less wonky way to do this? (I'm NOT interested in remote debugging.)

  Read the article

• Maven Cobertura: unit test failed but build success

  - by Pavel Drobushevich

  Hi all, I've configured cobertura code coverage in my pom: <plugin> <groupId>org.codehaus.mojo</groupId> <artifactId>cobertura-maven-plugin</artifactId> <version>2.4</version> <configuration> <instrumentation> <excludes> <exclude>**/*Exception.class</exclude> </excludes> </instrumentation> <formats> <format>xml</format> <format>html</format> </formats> </configuration> </plugin> And start test by following command: mvn clean cobertura:cobertura But if one of unit test fail Cobertura only log this information and doesn't mark build fail. Tests run: 287, Failures: 1, Errors: 1, Skipped: 0 Flushing results... Flushing results done Cobertura: Loaded information on 139 classes. Cobertura: Saved information on 139 classes. [ERROR] There are test failures. ................................. [INFO] BUILD SUCCESS How to configure Cobertura marks build failed in one of unit test fail? Thanks in advance.

  Read the article

• CCNet exception during build of vs2010 project

  - by sonee

  We have two build machines. Lately, we've migrated our projects to vs2010 from vs2005. But the problem is that one of the machines occurs error during build. Another machine works well, but just one machine shows error. The differences between the machines are os and computer spec. The machine which is working well is installed windows server 2003 and the other is windows7. the error message is unhandled exception: System.NullReferenceException: Microsoft.VisualStudio.Shell.ThreadHelper.InvokeOnUIThread(InvokableBase invokable) Microsoft.VisualStudio.Shell.ThreadHelper.Invoke(Action action)Microsoft.VisualStudio.Project.VS.Implementation.VSShellServices.InvokeOnUIThread(Action method) Microsoft.VisualStudio.Project.VisualC.VCProjectEngine.ApartmentMarshaler.Invoke(Action method) Microsoft.VisualStudio.Project.VisualC.VCProjectEngine.VCConfigBuildJob.BuildCompleted(BuildSubmission ar) Microsoft.VisualStudio.Project.Contracts.Implementation.BuildProjectBase.BuildCompletedCallbackManager.BuildCompleted(BuildSubmission buildSubmission) Microsoft.Build.Execution.BuildSubmission.<CheckForCompletion>b__0(Object state) System.Threading.QueueUserWorkItemCallback.WaitCallback_Context(Object state) System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem() System.Threading.ThreadPoolWorkQueue.Dispatch() System.Threading._ThreadPoolWaitCallback.PerformWaitCallback() Curiously enough, when I run building project in command line on the machine which occurs error, it works well. The machine just shows error when launched by ccnet. I've installed latest version of ccnet to all machines. Is there anybody who faced like this problem?

  Read the article

• Symbols (pdb) for native dll are not loaded due to post build step

  - by sean e

  I have a native release dll that is built with symbols. There is a post build step that modifies the dll. The post build step does some compression and probably appends some data. The pdb file is still valid however neither WinDbg nor Visual Studio 2008 will load the symbols for the dll after the post build step. What bits in either the pdb file or the dll do we need to modify to get either WinDbg or Visual Studio to load the symbols when it loads a dump in which our release dll is referenced? Is it filesize that matters? A checksum or hash? A timestamp? Modify the dump? or modify the pdb? modify the dll before it is shipped? (We know the pdb is valid because we are able to use it to manually get symbol names for addresses in dump callstacks that reference the released dll. It's just a total pain in the *ss do it by hand for every address in a callstack in all the threads.)

  Read the article

• Ant build script executing <sql> task using java code

  - by Jay

  Any idea, why none of the debugging comments are printed once after executing the ANT build script's SQL task via java code? The java class to execute the sql in build scirpt is public class AntRunnerTest { private Project project; public void executeTask(String taskName) { try { project = new Project(); project.init(); project.setBasedir(new String(".")); ProjectHelper helper = ProjectHelper.getProjectHelper(); project.addReference("ant.projectHelper", helper); helper.parse(project, new File("build-copy.xml")); System.out.println("Before"); project.executeTarget(taskName); System.out.println("After"); } catch(Exception ex) { System.out.println(ex.getMessage()); } } public static void main(String args[]) { try { AntRunnerTest newInst = new AntRunnerTest(); newInst.executeTask("sql"); } catch(Exception e) { System.out.println(""+e); } } } I dont see the debug String "After" getting printed in the console. I noticed this issue only when i try to execute a sql task using java code. The ant script has the following simple transaction tag in it. <transaction> <![CDATA[ select now() ]]> </transaction> Any thoughts? Thanks in advance.

  Read the article

• using .append to build a complex menu

  - by gneandr

  To build a menu block which should be switchable with hide/unhide of the menu items, I'm using .append html. The code idea is this: navigat += '<h3 class="infoH3"> <a id="' + menuID +'"' + ' href="javascript:slideMenu(\'' + menuSlider + '\');">' + menuName + '</a></h3>'; navigat += '<div id="' + menuSlider + '" style="display:none">'; navigat += ' <ul>'; navigat += ' <li>aMenu1</li>' navigat += ' <li>aMenu2</li>' navigat += ' <li>aMenu3</li>' navigat += ' </ul>'; navigat += '<!-- menuName Slider --></div>'; $("#someElement").append (navigat); This is doing well .. so far. But the point is:: I use JS to read the required menu items (eg. 'aMenu1' together with title and/or link info) from a file to build all that, eg. for 'aMenu1' a complex is composed and $("#someElement").append(someString) is used to add that the 'someElement'. At the moment I build those html elements line by line. Also OK .. as far as the resulting string has the opening and closing tag, eg. "<li>aMenu2</li>". As can be seen from above posted code there is a line "<div id="' + menuSlider + '" style="display:none">". Appending that -- AFAIS -- the .append is automatically (????) adding "</div>" which closes the statement. That breaks my idea of the whole concept! The menu part isn't included in the 'menuSlider '. QQ: How to change it -- NOT to have that "</div" added to it?? Günter

  Read the article

• How do I get Visual Studio build process to pass condition to library(external) project

  - by Billy Talented

  I have tried several solutions for this problem. Enough to know I do not know enough about MSBuild to do this elegantly but I feel like there should be a method. I have a set of libraries for working with .net projects. A few of the projects utilize System.Web.Mvc - which recently released Version 2 - and we are looking forward to the upgrade. Currently sites which reference this library reference it directly by the project(csproj) on the developer's computer - not a built version of the library so that changes and source code case easily be viewed when dealing code from this library. This works quite well and would prefer to not have to switch to binary references (but will if this is the only solution). The problem I have is that because of some of the functionality that was added onto the MVC1 based library (view engines, model binders etc) several of the sites reliant on these libraries need to stay on MVC1 until we have full evaluated and tested them on MVC2. I would prefer to not have to fork or have two copies on each dev machine. So what I would like to be able to do is set a property group value in the referencing web application and have this read by the above mentions library with the caviat that when working directly on the library via its containing solution I would like to be able to control this via Configuration Manager by selecting a build type and that property overriding the build behavior of the solution (i.e. 'Debug - MVC1' vs 'Debug -MVC2') - I have this working via: <Choose> <When Condition=" '$(Configuration)|$(Platform)' == 'Release - MVC2|AnyCPU' Or '$(Configuration)|$(Platform)' == 'Debug - MVC2|AnyCPU'"> <ItemGroup> <Reference Include="System.Web.Mvc, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35, processorArchitecture=MSIL"> </Reference> <Reference Include="Microsoft.Web.Mvc, Version=1.0.0.0, Culture=neutral, processorArchitecture=MSIL"> <SpecificVersion>False</SpecificVersion> <HintPath>..\Dependancies\Web\MVC2\Microsoft.Web.Mvc.dll</HintPath> </Reference> </ItemGroup> </When> <Otherwise> <ItemGroup> <Reference Include="System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35, processorArchitecture=MSIL"> <SpecificVersion>False</SpecificVersion> <HintPath>..\Dependancies\Web\MVC\System.Web.Mvc.dll</HintPath> </Reference> </ItemGroup> </Otherwise> The item that I am struggling with is the cross solution issue(solution TheWebsite references this project and needs to control which build property to use) that I have not found a way to work with that I think is a solid solution that enabled the build within visual studio to work as it has to date. Other bits: we are using VS2008, Resharper, TeamCity for CI, SVN for source control.

  Read the article

• Stop IIS 7 Application Pool from build script

  - by Andrew Hanson

  How can I stop and then restart an IIS 7 application pool from an MSBuild script running inside TeamCity. I want to deploy our nightly builds to an IIS server for out testers to view. I have tried using appcmd like so: appcmd stop apppool /apppool.name:MYAPP-POOL ... but I have run into elevation issues in Windows 2008 that so far have stopped me from being able to run that command from my TeamCity build process because Windows 2008 requires elevation in order to run appcmd. If I do not stop the application pool before I copy my files to the web server my MSBuild script is unable to copy the files to the server. Has anybody else seen and solved this issue when deploying web sites to IIS from TeamCity?

  Read the article

• Subsume external library into source tree with Autotools.

  - by troutwine

  I am developing a new project, using Autotools for my build infrastructure. I would like to subsume external dependencies into my source tree. These dependencies are using Autotools, as well. How can I configure my project's build scripts to build and link against subsumed dependencies? Though Duret-Lutz's tutorial is excellent, this situation is only briefly addressed in a few slides. I found his explanation deeply confusing. By adding the directory name of subsumed dependencies to the toplevel Makefile.am's SUBDIRS the dependency is being configured and built. It is possible to manually set include paths through CFLAGS, but how do I link against libtool .la files?

  Read the article

• Android ant script workaround?

  - by haseman

  It appears that, in the transition between the Android 1.1 sdk and 1.5, Google radically changed how ant scripts using AAPT can build Android projects. Previously they support args allowing developers to specify source, res, asset, and a manifest for a particular build. Now, they seem to allow developers to specify only a single folder containing everything. While I could rewrite all our build scripts to work in this new way, I rather like our current system (as it doesn't require more hours of work that I don't have). To that end, has anyone figured out how to go back to the pre 1.5 method of ant script building? Further, has anyone found a rational reason for this change?

  Read the article

• Create Custom Builds of an Xcode Project

  - by macinjosh

  I am going to build a Mac application written in Obj-C with Xcode. For argument's sake let's say it will have 10 optional features. I need a way to enable or disable those features to create custom builds of the application. These builds would be automated (most likely through the Mac OS X Terminal) so I would need a way to state which of these features are enabled/disabled at build time (a configuration file or CLI arguments would be ideal.) So what is the best way to accomplish this? I'm trying to plan this out before I start coding so that there is proper separation in my code base to allow for these features to come and go. Ideally the custom build would only contain compiled code for the features it should have. In other words I don't want to always compile all the features and condition them out at runtime.

  Read the article

• Issue while creating an android project with phonegap

  - by Mohit Jain

  When I try to create native android project in eclipse it works perfectly fine, and that shows my android setup is proper but when I try to create a phonegap project it create a error ie: ./create ~/Documents/workspace/HelloWorld com.fizzysoftware.HelloWorld HelloWorld BUILD FAILED /Users/mohit/Documents/eclipse/android-sdk-macosx/tools/ant/build.xml:710: The following error occurred while executing this line: /Users/mohit/Documents/eclipse/android-sdk-macosx/tools/ant/build.xml:723: Compile failed; see the compiler error output for details. Total time: 5 seconds An unexpected error occurred: ant jar > /dev/null exited with 1 Deleting project... cordova version: 2.7 Android api version 14 Ps: I am a ruby on rails developer. This is my day 1 with phonegap/android/ios

  Read the article

• Legacy Database, Fluent NHibernate, and Testing my mappings

  - by sdanna

  As the post title implies, I have a legacy database (not sure if that matters), I'm using Fluent NHibernate and I'm attempting to test my mappings using the Fluent NHibernate PersistenceSpecification class. My question is really a process one, I want to test these when I build locally in Visual Studio using the built in Unit Testing framework for now. Obviously this implies (I think) that I'm going to need a database. What are some options for getting this into the build? If I use an in memory database does NHibernate or Fluent NHibernate have some some mechanism for sucking the database schema from a target database or maybe the in memory database can do this? Will I need to manually get the schema to feed to an in memory database? Ideally I would like to get this this setup to where the other developers don't really have to think about it other than when they break the build because the tests don't pass.

  Read the article

• Building two executables in one project

  - by Rui Pacheco

  Hi, I've a project that must produce two executables: the main application and an executable that is called by a separate process. I've created the second file in Xcode and added a second target of type Cocoa Shell Tool. I can now build the second executable but when I try to build my project normally I get an error saying there's two executables present: ld: duplicate symbol _main in <path>/SecondExecutable.o and <path>/main.o (<path> was added by me to protect the innocent and their intelectual property). How can I configure Xcode to build both at the same time?

  Read the article

• integrating uppercut and cc.net

  - by deepasun

  I am trying to integrate uppercut and cc.net for getting build and revision... What do I have to put in the codebuild folder? while running cc.net, I'm getting svn folder Unable to execute file [D:\CodeBuild\abc\svn]. The file may not exist or may not be executable. ---> System.ComponentModel.Win32Exception: The system cannot find the file specified Without cc.net integration can we get both build and revision incremented? When will build and revision get incremented?

  Read the article

• Linux program in FreeBSD

  - by Alex Farber

  Trying to run my program in FreeBSD OS, I have the following results: $ ./myprogram ELF binary type "0" not known ./myprogram: 1: Syntax error: "&" unexpected (expecting ")") $ file myprogram myprogram: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), dynamically linked (uses shared libs), for GNU/Linux 2.6.15, not stripped The program is built In GCC on Ubuntu computer. What can I do? Can I build the program for FreeBSD on my Ubuntu computer by changing some build options, or I need to build it in FreeBSD OS? Maybe there is some way to convert executable to format recognized by FreeBSD?

  Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >