Search Results

Search found 67891 results on 2716 pages for 'windows virtual pc'.

Page 45/2716 | < Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >

  • Windows 8 using as a webserver

    - by Jason
    I have a few hobby websites that I currently host on CentOS 6. Apache, mail serving, PHP, MySQL nothing special. In the past I used Windows XP to do this same task, for years, and I was OK. I switched to Linux and for the last few years it has been such a pain. updates break, certain apps only support certain distros without compiling from source. It prevents me from working on my hobby sites more because I am always fixing something. With Windows I locked it down, I run a hardware firewall and packet analyser, kept up on updates and A/V and never had a problem. I dont allow RDC from outside the local LAN, no FTP open, run OpenSSH on an obscure port.. I am considering switching to Windows 8 (since it is a cheaper license now that Windows 7) and running apache, HMailServer, PHP, MySQL, just like my CentOS install. My questions: I am not familiar with Windows 8, can the above be done like XP? No new security restrictions or the OS preventing this from happening? The machine is a Athlon 64-bit X2 with 32GB of RAM. Will Windows 8 see all of the RAM? Technically the machine came with Windows 7, and there is a serial number on it but I am sure I wiped away the Windows 7 recovery partition when I switched to Linux....

    Read the article

  • How to connect the virtual networks of vmware guests running on different hosts?

    - by gyrolf
    In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

    Read the article

  • Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

    - by teenup
    Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

    Read the article

  • Customize your icons in Windows 7 and Vista

    - by Matthew Guay
    Want to change out the icons on your desktop and more?  Personalizing your icons is a great way to make your PC uniquely yours,, and today we show you how to grab unique icons, and default Winnows. to be your own. Change the icon for Computer, Recycle Bin, Network, and your User folder Right-click on the desktop, and select Personalize. Now, click the “Change desktop icons” link on the left sidebar in the Personalization window. The window looks slightly different in Windows Vista, but the link is the same. Select the icon you wish to change, and click the Change Icon button.  In Windows 7, you will also notice a box to choose whether or not to allow themes to change icons, and you can uncheck it if you don’t want themes to change your icon settings. You can select one of the other included icons, or click browse to find the icon you want.  Click Ok when you are finished. Change Folder icons You can easily change the icon on most folders in Windows Vista and 7.  Simply right-click on the folder and select properties. Click the Customize tab, and then click the Change Icon button.  This will open the standard dialog to change your icon, so proceed as normal. This basically just creates a hidden desktop.ini file in the folder containing the following or similar data: [.ShellClassInfo]IconFile=%SystemRoot%\system32\SHELL32.dllIconIndex=20 You could manually create or edit the file if you choose, instead of using the dialogs. Simply create a new text file named desktop.ini with this same information, or edit the existing one.  Change the IconFile line to the location of your icon. If you are pointing to a .ico file you should change the IconIndex line to 0 instead. Note that this isn’t available for all folders, for instance you can’t use this to change the icon for the Windows folder.   In Windows 7, please note that you cannot change the icon of folder inside a library.  So if you are browsing your Documents library and would like to change an icon in that folder, right-click on it and select Open folder location.  Now you can change the icon as above. And if you would like to change a Library’s icon itself, then check out this tutorial: Change Your Windows 7 Library Icons the Easy Way Change the icon of any file type Want to make you files easier to tell apart?  Check out our tutorial on how to simply do this: Change a File Type’s Icon in Windows 7 Change the icon of any Application Shortcut To change the icon of a shortcut on your desktop, start menu, or in Explorer, simply right-click on the icon and select Properties. In the Shortcut tab, click the Change Icon button. Now choose one of the other available icons or click browse to find the icon you want. Change Icons of Running Programs in the Windows 7 taskbar If your computer is running Windows 7, you can customize the icon of any program running in the taskbar!  This only works on applications that are running but not pinned to the taskbar, so if you want to customize a pinned icon you may want to unpin it before customizing it.  But the interesting thing about this trick is that it can customize any icon anything running in the taskbar, including things like Control Panel! Right-click or click and push up to open the jumplist on the icon, and then right-click on the program’s name and select Properties.  Here we are customizing Control Panel, but you can do this on any application icon. Now, click Change Icon as usual. Select an icon you want (We switched the Control Panel icon to the Security Shield), or click Browse to find another icon.  Click Ok when finished, and then close the application window. The next time you open the program (or Control Panel in our example), you will notice your new icon on its taskbar icon. Please note that this only works on applications that are currently running and are not pinned to the taskbar.  Strangely, if the application is pinned to the taskbar, you can still click Properties and change the icon, but the change will not show up. Change the icon on any Drive on your Computer You can easily change the icon on your internal hard drives and portable drives with the free Drive Icon Changer application.  Simply download and unzip the file (link below), and then run the application as administrator by right-clicking on the icon and selecting “Run as administrator”. Now, select the drive that you want to change the icon of, and select your desired icon file. Click Save, and Drive Icon Changer will let you know that the icon has been changed successfully. You will then need to reboot your computer to complete the changes.  Simply click Yes to reboot. Now, our Drive icon is changed from this default image: to a Laptop icon we chose! You can do this to any drive in your computer, or to removable drives such as USB flash drives.  When you change these drives icons, the new icon will appear on any computer you insert the drive into.  Also, if you wish to remove the icon change, simply run the Drive Icon Changer again and remove the icon path. Download Drive Icon Changer This application actually simply creates or edits a hidden Autorun.inf file on the top of your drive.  You can edit or create the file yourself by hand if you’d like; simply include the following information in the file, and save it in the top directory of your drive: [autorun]ICON=[path of your icon] Remove Arrow from shortcut icons Many people don’t like the arrow on the shortcut icon, and there are two easy ways to do this. If you’re running the 32 bit version of Windows Vista or 7, simply use the Vista Shortcut Overlay Remover. If your computer is running the 64 bit version of Windows Vista or 7, use the Ultimate Windows Tweaker instead.  Simply select the Additional Tweaks section, and check the “Remove arrows from Shortcut Icons.” For more info and download links check out this article: Disable Shortcut Icon Arrow Overlay in Windows 7 or Vista Closing: This gives you a lot of ways to customize almost any icon on your computer, so you can make it look just like you want it to.  Stay tuned for more great desktop customization articles from How-to Geek! Similar Articles Productive Geek Tips Change Start Menu to Use Small Icons in Windows 7 or VistaResize Icons Quickly in Windows 7 or Vista ExplorerRoundup: 16 Tweaks to Windows Vista Look & FeelRestore Missing Desktop Icons in Windows 7 or VistaClean Up Past Notification Icons in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox) Get Better Windows Search With UltraSearch Scan News With NY Times Article Skimmer

    Read the article

  • Make the Taskbar Buttons Switch to the Last Active Window in Windows 7

    - by The Geek
    The new Windows 7 taskbar’s Aero Peek feature, with the live thumbnails of every window, is awesome… but sometimes you just want to be able to click the taskbar button and have the last open window show up instead. Here’s a quick hack to make it work better. To better understand the problem, imagine having nine windows of the same type open on your screen, but you are primarily working in just one of the windows at a time. So every time you want to switch back, you have to click the taskbar button, and then choose the one you are using from the list, which can be pretty annoying… Now if you know your Windows 7 shortcuts, you’d know that you can simply hold down the Ctrl key while clicking on the taskbar button, and the last window will show up. In fact, you can keep holding down the Ctrl key and keep clicking, and Windows will cycle through the open windows. It’s a useful shortcut, but hardly something you want to do every single time. Instead, we’ll use a quick registry hack to make the normal click switch to the last open window—if you still want to see the thumbnail list, just hover your mouse over the button for half a second to see the full list. Manual Registry Hack for Last Active Window Open up regedit.exe through the start menu search or run box, and then head down to the following registry key: HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced Once you’re there, create a new 32-bit DWORD value on the right hand side, give it the name LastActiveClick, and set the value to 1. Once you are done, it should look something like this: Once you are done, you’ll have to log off and back on, or you can kill Explorer.exe through Task Manager and re-open it. Download the Registry Hack Instead Since you probably don’t feel like registry hacking, we’ve provided you an easy downloadable version. You can simply download the file, extract it, and then double-click on the LastActiveClick.reg file. Once you are done, you’ll have to log off and back on, just like with the manual registry hack. Download LastActiveClick Registry Hack from howtogeek.com Similar Articles Productive Geek Tips Make the Windows 7 Taskbar Work More Like Windows XP or VistaStupid Geek Tricks: Select Multiple Windows on the TaskbarReorganize Your Taskbar Buttons and Tray Icons in XP/VistaKeyboard Ninja: Create a Hotkey to Switch to Your Open Outlook WindowTaskbar Eliminator Does What the Name Implies: Hides Your Windows Taskbar TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow

    Read the article

  • Hyper-V virtual machine can't be migrated to a specific host in the cluster

    - by Massimo
    I have a three-node Hyper-V cluster running on Windows Server 2008 R2 which is working quite flawlessly: there are no errors, live migration works, all hosts can and will happily run all virtual machines, and so on. But one specific virtual machinee is trying to make me go mad: it works on two nodes of the cluster, but not on the third one. Whenever I try to move the VM to that node, be it in a live migration or with the VM powered off, it always fails. In the event log of the host these events are logged: Source: Hyper-V-VMMS Event ID: 16300 Cannot load a virtual machine configuration: General access denied error (0x80070005) (Virtual machine ID <GUID>) Source: Hyper-V-VMMS Evend ID: 20100 The Virtual Machine Management Service failed to register the configuration for the virtual machine '<GUID>' at 'C:\ClusterStorage\<PATH>\<VM>': General access denied error (0x80070005) Source: Hyper-V-High-Availability Event ID: 21102 'Virtual Machine Configuration <VM>' failed to register the virtual machine with the virtual machine management service. All other VMs can be moved to/from the offending host, and the offending VM can be moved between the other two hosts. Also, this is not a storage problem, because there are other VMs in the same cluster volume, and the host has no troubles running them. What's going on here?

    Read the article

  • How can I restore "Open With" context menu item in Windows 7?

    - by Izzy Helianthus
    I tried various way to fix this problem but ended up with a dead end. My problem would be the missing "Open With" context menu items (or subitems?). It did not appear even though I hovered it for a minutes or two. Below is a screenshot of the respective right-click menu. Note: The only problem with "Open With" is at the right-click menu (as well as FILE menu). Edited: The "Open With" context submenu that only accessible at the top, while the typical right click menu doesn't work. Repaste from Comment. I don't think it's involved with any windows files because other user in the same computer doesn't affected at all. I can see the "Open With" context submenu. I believe this must have involved with current user's registry. It happens to all files (any file types, except folder). I can only use Open With by clicking at the file and select it manually at the top of Explorer window. (Refer to the link for the screenshot)

    Read the article

  • Why isn't 'Low Fragmentation Heap' LFH enabled by default on Windows Server 2003?

    - by James Wiseman
    I've been investigating an issue with a production Classic ASP website running on IIS6 which seems indicative of memory fragmentation. One of the suggestions of how to ameliorate this came from Stackoverflow: How can I find why some classic asp pages randomly take a real long time to execute?. It suggested flipping a setting in the site's global.asa file to 'turn on' Low Fragmentation Heap (LFH). The following code (with a registered version of the accompanying DLL) did the trick. Set LFHObj=CreateObject("TURNONLFH.ObjTurnOnLFH") LFHObj.TurnOnLFH() application("TurnOnLFHResult")=CStr(LFHObj.TurnOnLFHResult) (Really the code isn't that important to the question). An author of a linked post reported a seemingly magic resolution to this issue, and, reading around a little more, I discovered that this setting is enabled by default on Windows Server 2008. So, naturally, this left me a little concerned: Why is this setting not enabled by default on 2003, or If it works in 2008 why have Microsoft not issued a patch to enable it by default on 2003? I suspect the answer to the above is the same for both (if there is one). Obviously, we're testing it in a non-production environment, and doing an array of metrics and comparisons to deem if it does help us. But aside from this I'm really just trying to understand if there's any technical reason why we should do this, or if there are any gotchas that we need to be aware of.

    Read the article

  • Disadvantages of enabling 'Low Fragmentation Heap' LFH on Windows Server 2003?

    - by James Wiseman
    I've been investigating an issue with a production Classic ASP website running on IIS6 which seems indicative of memory fragmentation. One of the suggestions of how to ameliorate this came from Stackoverflow: How can I find why some classic asp pages randomly take a real long time to execute?. It suggested flipping a setting in the site's global.asa file to 'turn on' Low Fragmentation Heap (LFH). The following code (with a registered version of the accompanying DLL) did the trick. Set LFHObj=CreateObject("TURNONLFH.ObjTurnOnLFH") LFHObj.TurnOnLFH() application("TurnOnLFHResult")=CStr(LFHObj.TurnOnLFHResult) (Really the code isn't that important to the question). An author of a linked post reported a seemingly magic resolution to this issue, and, reading around a little more, I discovered that this setting is enabled by default on Windows Server 2008. So, naturally, this left me a little concerned: Why is this setting not enabled by default on 2003, or If it works in 2008 why have Microsoft not issued a patch to enable it by default on 2003? I suspect the answer to the above is the same for both (if there is one). Obviously, we're testing it in a non-production environment, and doing an array of metrics and comparisons to deem if it does help us. But aside from this I'm really just trying to understand if there's any technical reason why we should do this, or if there are any gotchas that we need to be aware of.

    Read the article

  • Windows Vista Update Now Wont Boot Up

    - by thatryan
    My friend just updated her Windows Vista to service pack 1, or tried to. Now it wont boot up. Just black screen, some errors etc. I tried googling it and lots of people had this problem it seems. Anyone find a fix for it? I read somewhere I believe that Microsoft said to delete some files, Nvidia maybe? But I can not find that again, I forgot the exact error code I searched for before. Does anyone know what I am talking about? LOL Thanks guys.

    Read the article

  • Refresh Windows Explorer in Win7

    - by Paja
    My program sets "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" value "Hidden". Hovewer I'm not able to refresh the explorer to take into account this change. I've tried: 1) SHChangeNotify(SHCNE_ASSOCCHANGED, SHCNF_IDLIST, IntPtr.Zero, IntPtr.Zero);` 2) SHELLSTATE state = new SHELLSTATE(); state.fShowAllObjects = (uint)1; SHGetSetSettings(ref state, SSF.SSF_SHOWALLOBJECTS, true); 3) SendMessageTimeout(HWND_BROADCAST, WM_SETTINGCHANGE, SPI_SETNONCLIENTMETRICS, 0, SMTO_ABORTIFHUNG, 5000, ref dwResult); 4) SendMessage(HWND_BROADCAST, WM_COMMAND, 28931 /* Refresh */, 0); Nothing works. So what should I do? If I refresh Explorer myself with F5, then it works. Hovewer I would like some elegant solution, so it would refresh the display everywhere, even in OpenFile/SaveFile dialogs, which are currently open. I'm using C# .NET, Win7.

    Read the article

  • Win C#: Refresh Windows Explorer in Win7

    - by Paja
    Hello, My program sets "HKCU\Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced" value "Hidden". Hovewer I'm not able to refresh the explorer to take into account this change. I've tried: 1) SHChangeNotify(SHCNE_ASSOCCHANGED, SHCNF_IDLIST, IntPtr.Zero, IntPtr.Zero); 2) SHELLSTATE state = new SHELLSTATE(); state.fShowAllObjects = (uint)1; SHGetSetSettings(ref state, SSF.SSF_SHOWALLOBJECTS, true); 3) SendMessageTimeout(HWND_BROADCAST, WM_SETTINGCHANGE, SPI_SETNONCLIENTMETRICS, 0, SMTO_ABORTIFHUNG, 5000, ref dwResult); 4) SendMessage(HWND_BROADCAST, WM_COMMAND, 28931 /* Refresh */, 0); Nothing works. So what should I do? If I refresh Explorer myself with F5, then it works. Hovewer I would like some elegant solution, so it would refresh the display everywhere, even in OpenFile/SaveFile dialogs, which are currently open. I'm using C# .NET, Win7. Thank you.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • How do you get Windows Mobile Device Center to detect a Windows Phone 7 Series emulator?

    - by sweeney
    Hello, I'm running some tests and need to be able to get Windows Phone 7 Series emulator synced with an exchange account or local Outlook account via the Device Center. I'm using the unlocked version of the emulator so that i actually have a reasonable set of software on the phone to work with. When the emulator launches i expect the Device Center to detect it and start syncing (or prompt me for settings). This does not happen. I've tried adjusting the Connection Settings (COM2 and DMA) in the Device Center with no luck. Is this possible? Has anyone done it? Thanks in advance!

    Read the article

  • Connect to host computer from Virtual PC 2007

    - by Vegard Larsen
    I am having trouble using my guest (Windows XP SP3) to communicate over TCP/IP to the host computer (Windows 7) using Virtual PC 2007. I have WAMPServer running on my host, and want to be able to access the websites on there from my guest OS. What do I do to make this work? What is the IP address of the host computer when using Shared Networking? As far as I can tell "Internal Networking" won't work, because that only allows communication between the guests, not between a guest and the host.

    Read the article

  • Upgrade OEM Windows 7 Pro to Windows 7 Enterprise

    - by user17111
    Our hardware vendor has sold us a laptop that comes with Windows 7 Pro OEM. Since we want Windows 7 Enterprise (for features like DirectAccess and BitLocker), the vendor has supplied us with a Software Assurance only license to upgrade OEM Win 7 Pro to Win 7 Ent. Do I need to install Windows 7 Enterprise Volume License media and re-install Windows, or is there a process to turn this existing Windows 7 Pro install into an "Enterprise" ?

    Read the article

  • Windows 98 style flat icons in Windows XP

    - by Senthil
    I am using Windows XP. I am tired of looking at the folder icons in Windows XP. I changed the color depth to 256 colors and the folder icons in Windows Explorer changed to the flat - windows 95/98 style icons. I loved them! is there a way to tell windows explorer to show those flat old style icons for folders? without going to 8-bit? Note: I am okay with going down from 32-bit, but 8 is way too low to work with.

    Read the article

  • Could one hypothetically upgrade a computer from Windows 95 to Windows 8

    - by JMK
    Hypothetically, could you start with a computer running Windows 95, upgrade this to Windows 98, then upgrade this to Windows XP, then upgrade this to Vista, then to 7 and finally to 8 (consumer preview)? What state would the OS be in after so many upgrades? Would any of the native Windows 95 apps still be sticking around in Windows 8? Has anybody done anything like this before? I don't need to do this, I am just asking out of curiosity! Thanks

    Read the article

  • Need clear steps on how to convert a Windows 2000 Server to a XenServer VM

    - by Jay
    The source system is not local. The target host running XenServer is not local. The source system is running Windows 2000 Server SP4 and has 1 disk split into 6 partitions, all NTFS: C: 6 GB (boot) D: 15 GB E: 6 GB F: 6 GB G: 5 GB H: 26 GB Most of the partitions are mostly mostly full ( 60%). What is the most straightforward way to do a P2V migration of the server? I can do minor database & data syncs after the P2V is successful & running as a VM within XenServer, it's just getting to that point which is not clear. The option of installing a Windows 2000 Server from scratch is not available, I need to convert the existing physical server as-is into a VM to be hosted within a XenServer environment. I've looked at XenConvert but it maxes out on converting only 4 partitions in one shot, and I'm not certain how to account for the 2 extra partitions. I'm not familiar with XenServer but it's my only option right now to go P2V.

    Read the article

  • PC: Quick Freeze, then BSOD, then forced reboot, then freezes again

    - by cr0z3r
    Lately I have been experiencing a weird issue. My PC will hang for a second and then BSOD - it stays there, so I have to reboot. Once Windows starts again and I'm logged in, after 1-10min it freezes again, this time without BSOD. RECAP: 1 second freeze BSOD, hangs there I have to force-reboot Once PC rebooted, I log back into Windows second freeze between a 1-10min range, no BSOD (alternatively, I get a freeze with a constant sound/noise, no BSOD) I contacted my PC provider, who told me my graphics-card might be flawed (Quadro 4000), so I used a Quadro 2000 that they lend me. The issue still occurred. The issue now seemed to belong to a flawed RAM module. Following my provider's steps, I removed all but the first from the left column and kept using my PC for a week or so without any issues. I then added the bottom-right module, and so on, until all modules were back inside - I had no problems. Now it seemed that a simple take-out-put-back-in of the RAM modules had fixed the issue. However, after a few months, the issue was back. I redid all the RAM-swapping I had done before, and concluded that the lower-right module was flawed. My provider changed it for another, and everything was great until now. My PC froze again for barely a second, hanged on a BSOD, I rebooted it, logged-in to Windows to get a freeze (without BSOD or reboot) 40 seconds later. Something worth noting, is that every time I reboot after the BSOD, it is something within Chrome that freezes my PC (e.g. this time I clicked the "restore" button as Chrome mentioned it had exited unexpectedly - from the previous freeze obviously - and it instantly froze). Finally, the Event Viewer lists 2 critical events in the past hour as "ID: 41, Type: Kernel-Power". PC-Specs: http://i.imgur.com/VZpbr.jpg Previous Dump-files: https://dl.dropbox.com/u/716600/DumpFiles_08_2012.zip I would like to thank anybody in advance for your help. You're great. UPDATE 1: I realized that I did not mention an awkward fact about this issue. After I have gotten the 1-sec freeze followed by a BSOD, after I rebooted because the BSOD hanged, and after I logged back in to get another (this time, eternal) freeze and rebooted once again, the PC does not boot back up. The power-light is on, but my monitor says "no signal", as if the PC wouldn't really be turned on. This truly seems a like a power-related issue, doesn't it? UPDATE 2: I just got a freeze, but without BSOD. My screen froze (while on Chrome, which is starting to seem suspicious to me) with an ongoing sound/noise. I had to force-reboot my PC. I would say this is a graphics-card issue, but this issue also happened when I was using the Quadro 2000 from my provider. UPDATE 3: I just got a BSOD while trying to render something (quite heavy, actually) in 3ds Max 2012. I left the BSOD "running", as it said it was writing dump files to disk. However, the percentage number stayed at 0, so after 15 minutes I force-rebooted. I then used the software WhoCrashed (thank you Dave) which reported the following from the C:\Windows\Memory.dmp file: On Thu 22.11.2012 22:13:45 GMT your computer crashed crash dump file: C:\Windows\memory.dmp uptime: 01:05:27 This was probably caused by the following module: Unknown () Bugcheck code: 0x124 (0x0, 0xFFFFFA80275AC028, 0xF200001F, 0x100B2) Error: WHEA_UNCORRECTABLE_ERROR Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA). This is likely to be caused by a hardware problem problem. This problem might be caused by a thermal issue. A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: Unknown . Google query: Unknown WHEA_UNCORRECTABLE_ERROR

    Read the article

  • Diagnosing RAM issues

    - by TaylorND
    I have an old Acer Aspire T180 desktop. The specs are as follows: AMD Athlon 64 3800+ 2.4GHz 1GB DDR2 SDRAM 160GB DVD-Writer (DVD±R/±RW) Gigabit Ethernet 17" Active Matrix TFT Color LCD Windows Vista Home Basic Mini-tower AST180-UA381B According to the information in the computer's documentation the computer comes with 1 GB of RAM. It has two DDR2 SDRAM sticks. I used to have Windows Vista installed. Then I removed it and install Windows 7, and now I have since removed Windows 7 and installed Windows XP. According to Windows XP with both RAM sticks in the computer has 768 MB. Isn't this supposed to be 1 GB of RAM or 1024 MB of RAM? Is the amount of RAM installed only partly used by the Operating System? Is there's something I'm missing? If I remove either one of the RAM sticks I'm left with 448 MB of RAM. These numbers don't seem to add up. If each of the RAM sticks contains at least 448 MB of RAM shouldn't they (both being in) provide 896 MB of RAM. Even then, isn't that less than a GB of RAM? I'm not too experienced in hardware so I thought this would be the best place to ask. As a follow up question, is the RAM I have enough to run/multitask with Windows XP efficiently? I plan to do a lot of computing with the system (although not gaming), should I invest in more RAM?

    Read the article

  • How To Quickly Reboot Directly from Windows 7 to XP, Vista, or Ubuntu

    - by The Geek
    One of the biggest annoyances with a dual-boot system is having to wait for your PC to reboot to select the operating system you want to switch to, but there’s a simple piece of software that can make this process easier. This guest article was written by Ryan Dozier from the Doztech tech blog. With a small piece of software called iReboot we can skip the above step all together and instantly reboot into the operating system we want right from Windows. Their description says: “Instead of pressing restart, waiting for Windows to shut down, waiting for your BIOS to post, then selecting the operating system you want to boot into (within the bootloader time-limit!); you just select that entry from iReboot and let it do the rest!” Don’t worry about iReboot reconfiguring  your bootloader or any dual boot configuration you have. iReboot will only boot the selected operating system once and go back to your default settings. Using iReboot iReboot is quick and easy to install. Just download it, link below, run through the setup and select the default configuration. iReboot will automatically figure out what operating systems you have installed and appear in the taskbar. Go over to the taskbar and right click on the iReboot icon and select which operating system you want to reboot into. This method will add a check mark on the operating system you want to boot into. On your next reboot the system will automatically load your choice and skip the Windows Boot Manager. If you want to reboot automatically just select “Reboot on Selection” in the iReboot menu.   To be even more productive, you can install iReboot into each Windows operating system to quickly access the others with a few simple clicks.   iReboot does not work in Linux so you will have to reboot manually. Then wait for the Windows Boot Manager to load and select your operating system.   Conclusion iReboot works on  Windows XP, Windows Vista,  and Windows 7 as well as 64 bit versions of these operating systems. Unfortunately iReboot is only available for Windows but you can still use its functionality in Windows to quickly boot up your Linux machine. A simple reboot in Linux will take you back to Windows Boot Manager. Download iReboot from neosmart.net Editor’s note: We’ve not personally tested this software over at How-To Geek, but Neosmart, the author of the software, generally makes quality stuff. Still, you might want to test it out on a test machine first. If you’ve got any experience with this software, please be sure to let your fellow readers know in the comments. Similar Articles Productive Geek Tips Restart the Ubuntu Gnome User Interface QuicklyKeyboard Ninja: 21 Keyboard Shortcut ArticlesTest Your Computer’s Memory Using Windows Vista Memory Diagnostic ToolEnable or Disable UAC From the Windows 7 / Vista Command LineSet Windows as Default OS when Dual Booting Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon

    Read the article

  • Windows update error code : 80244004

    - by Hamidreza
    I am using Windows 7 and ESET SMART SECURITY 5 . Today I wanted to update my computer using Windows Update but it does give me error : Error(s) found: Code 80244004        Windows Update encountered an unknown error. My System Info : Sony Vaio EA2gfx , Ram : 4GB DDR2 , CPU: Intel Core i 5 I checkd out this links but they didn't help : http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_update/while-updating-i-am-getting-the-error-code/0b9b756c-5b6e-4571-838e-f90c48a4e00c https://www.calguns.net/calgunforum/showthread.php?t=583860 http://www.sevenforums.com/windows-updates-activation/235807-windows-update-error-80244004-a.html Please help me, thanks.

    Read the article

  • Can't boot up computer windows 8 installation

    - by danny ramirez
    I wanted to install Windows 8 with a volume partition and when the Windows 8 was installing it rebooted and it gave me an error: The digital signature for this file couldn't be verified. File :windows \system 32\winload.exe error code 0xc0000428. I have tried bootec commands and they didn't seem to fix it. Also my Windows 7 got deleted and I only have to boot with the Windows 8 error, so I can't do anything not even boot to safe mode. I have tried to install Windows 8 from disk later on and it won't let me because it keeps rebooting and starting the installation again, so I took off the disk before it rebooted and it takes me to that error again. Remember that's my only boot option so I'm stuck in the installation disk.

    Read the article

  • windows firewall broken on server 2008

    - by Chloraphil
    This evening I tried to rdp into my server 2008 box and was unable to. After poking around some I discovered that something is awry with my Windows Firewall. I did install 5 windows updates remotely earlier today but rolled those back in an attempt to see if that fixed the problem but had no luck. Symptoms: cannot rdp to machine (including from itself) cannot ping machine cannot connect to file share on machine error message when attempting to open "windows firewall with advanced security" snap-in (there was an error opening the windows firewall with advanced security snap-in ... The Windows Firewall with Advanced Security snap-in failed to load. Restart the windows firewall service on the computer that you are managing. Error code: 0x6D9. When I opened the "user-friendly" Windows Firewall it failed to load most of the gui elements, meaning, the title bar with close, minimize, and maximize buttons is present, the rest of the window has a white background with a yellow rectangle with rounded corners and a yellow triangle w/ an exclamation point is in the upper right. hope that made sense "Windows Firewall" does not appear in the list of services I ran a virus scan that found nothing. How do I fix the firewall and hopefully restore the ability to rdp? EDIT: Added at fission's request: c:\sc query mpsdrv SERVICE_NAME: mpsdrv TYPE : 1 KERNEL_DRIVER STATE : 4 RUNNING (STOPPABLE, NOT_PAUSABLE, IGNORES_SHUTDOWN) WIN32_EXIT_CODE : 0 (0x0) SERVICE_EXIT_CODE : 0 (0x0) CHECKPOINT : 0x0 WAIT_HINT : 0x0 c:\sc query mpssvc SERVICE_NAME: mpssvc TYPE : 20 WIN32_SHARE_PROCESS STATE : 1 STOPPED WIN32_EXIT_CODE : 1068 (0x42c) SERVICE_EXIT_CODE : 0 (0x0) CHECKPOINT : 0x0 WAIT_HINT : 0x0 Those two registry keys do exist: HKLM\SYSTEM\CurrentControlSet\Services\mpsdrv & HKLM\SYSTEM\CurrentControlSet\Services\MpsSvc ! The problem seems to be with the Base Filtering Engine, when I try to start it I get the following error: Windows could not start the Base Filtering Engine service on MYCOMPUTER. Error 15100: The resource loader failed to find MUI file. EDIT2: I ran sfc /scannow and i found about 100 occurrences of "[SR] Cannot repair member file"... including several related to the firewall (ex: [l:32{16}]"Firewall.cpl.mui" of Networking-MPSSVC.Resources...). One of them mentioned wordpad.exe, which I tried to open, and it failed. I found here mentions of mounting the install.wim on the install media to copy the affected files over. I am downloading the appropriate AIK and will continue tomorrow evening.

    Read the article

< Previous Page | 41 42 43 44 45 46 47 48 49 50 51 52  | Next Page >