Search Results

Search found 11567 results on 463 pages for 'map provider'.

Page 450/463 | < Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >

• Sonicwall VPN, Domain Controller Issues

  - by durilai

  I am trying to get the domain logon script to execute when I connect to VPN. I have a SonicWall 4060PRO, with the SonicOS Enhanced 4.2.0.0-10e. The VPN connects successfully, but the script does not execute. I am posting the log below, but I see two issues. The first is the inability to connect to domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. The second is the failure of the script. 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found.. I assume the second issue is caused because of the first, also on the second issue it seems to be trying to get the logon script from my local PC, not the server. Finally, the DC can be pinged and reached by its computer name once the VPN is connected. The shares that the script is tring to map can be mapped manually. Any help is appreciated. 2009/12/18 19:49:31:063 Information The connection "GroupVPN_0006B1030980" has been enabled. 2009/12/18 19:49:32:223 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:32:289 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX XAuth has requested a username but one has not yet been specified. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX Sending phase 1 delete. 2009/12/18 19:49:32:336 Information XXX.XXX.XXX.XXX User authentication information is needed to complete the connection. 2009/12/18 19:49:32:393 Information An incoming ISAKMP packet from XXX.XXX.XXX.XXX was ignored. 2009/12/18 19:49:36:962 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 1 negotiation. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Starting aggressive mode phase 1 exchange. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX NAT Detected: Local host is behind a NAT device. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX The SA lifetime for phase 1 is 28800 seconds. 2009/12/18 19:49:37:036 Information XXX.XXX.XXX.XXX Phase 1 has completed. 2009/12/18 19:49:37:094 Information XXX.XXX.XXX.XXX Received XAuth request. 2009/12/18 19:49:37:100 Information XXX.XXX.XXX.XXX Sending XAuth reply. 2009/12/18 19:49:37:110 Information XXX.XXX.XXX.XXX Received initial contact notify. 2009/12/18 19:49:37:153 Information XXX.XXX.XXX.XXX Received XAuth status. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX Sending XAuth acknowledgement. 2009/12/18 19:49:37:154 Information XXX.XXX.XXX.XXX User authentication has succeeded. 2009/12/18 19:49:37:247 Information XXX.XXX.XXX.XXX Received request for policy version. 2009/12/18 19:49:37:253 Information XXX.XXX.XXX.XXX Sending policy version reply. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Received policy change is not required. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX Sending policy acknowledgement. 2009/12/18 19:49:37:303 Information XXX.XXX.XXX.XXX The configuration for the connection is up to date. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting ISAKMP phase 2 negotiation with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP. 2009/12/18 19:49:37:377 Information XXX.XXX.XXX.XXX Starting quick mode phase 2 exchange. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX The SA lifetime for phase 2 is 28800 seconds. 2009/12/18 19:49:37:472 Information XXX.XXX.XXX.XXX Phase 2 with 10.10.10.0/255.255.255.0:BOOTPC:BOOTPS:UDP has completed. 2009/12/18 19:49:37:896 Information Renewing IP address for the virtual interface (00-60-73-4C-3F-45). 2009/12/18 19:49:40:189 Information The virtual interface has been added to the system with IP address 10.10.10.112. 2009/12/18 19:49:40:319 Information The system ARP cache has been flushed. 2009/12/18 19:49:40:576 Information XXX.XXX.XXX.XXX NetWkstaUserGetInfo returned: user: Dustin, logon domain: DT-WIN7, logon server: DT-WIN7 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX NetGetDCName failed: Could not find domain controller for this domain. 2009/12/18 19:49:53:457 Information XXX.XXX.XXX.XXX calling NetUserGetInfo: Server: , User: Dustin, level: 3 2009/12/18 19:49:53:460 Information XXX.XXX.XXX.XXX NetUserGetInfo returned: home dir: , remote dir: , logon script: 2009/12/18 19:49:53:466 Warning XXX.XXX.XXX.XXX Failed to execute script file \DT-WIN7netlogondomain.bat, Last Error: The network name cannot be found..

  Read the article

• IIS 7 Authentication: Certain users can't authenticate, while almost all others can.

  - by user35335

  I'm using IIS 7 Digest authentication to control access to a certain directory containing files. Users access the files through a department website from inside our network and outside. I've set NTFS permissions on the directory to allow a certain AD group to view the files. When I click a link to one of those files on the website I get prompted for a username and password. With most users everything works fine, but with a few of them it prompts for a password 3 times and then get: 401 - Unauthorized: Access is denied due to invalid credentials. But other users that are in the group can get in without a problem. If I switch it over to Windows Authentication, then the trouble users can log in fine. That directory is also shared, and users that can't log in through the website are able to browse to the share and view files in it, so I know that the permissions are ok. Here's the portion of the IIS log where I tried to download the file (/assets/files/secure/WWGNL.pdf): 2010-02-19 19:47:20 xxx.xxx.xxx.xxx GET /assets/images/bullet.gif - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 200 0 0 218 2010-02-19 19:47:20 xxx.xxx.xxx.xxx GET /assets/images/bgOFF.gif - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 200 0 0 218 2010-02-19 19:47:21 xxx.xxx.xxx.xxx GET /assets/files/secure/WWGNL.pdf - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 401 2 5 0 2010-02-19 19:47:36 xxx.xxx.xxx.xxx GET /assets/files/secure/WWGNL.pdf - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 401 1 2148074252 0 2010-02-19 19:47:43 xxx.xxx.xxx.xxx GET /assets/files/secure/WWGNL.pdf - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 401 1 2148074252 15 2010-02-19 19:47:46 xxx.xxx.xxx.xxx GET /manager/media/script/_session.gif 0.19665693119168282 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 200 0 0 203 2010-02-19 19:47:46 xxx.xxx.xxx.xxx POST /manager/index.php - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 200 0 0 296 2010-02-19 19:47:56 xxx.xxx.xxx.xxx GET /assets/files/secure/WWGNL.pdf - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 401 1 2148074252 15 2010-02-19 19:47:59 xxx.xxx.xxx.xxx GET /favicon.ico - 80 - 10.5.16.138 Mozilla/5.0+(Windows;+U;+Windows+NT+6.1;+en-US)+AppleWebKit/532.5+(KHTML,+like+Gecko)+Chrome/4.0.249.89+Safari/532.5 404 0 2 0 Here's the Failed Logon attempt in the Security Log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 2/19/2010 11:47:43 AM Event ID: 4625 Task Category: Logon Level: Information Keywords: Audit Failure User: N/A Computer: WEB4.net.domain.org Description: An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: jim.lastname Account Domain: net.domain.org Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: - Source Network Address: 10.5.16.138 Source Port: 50065 Detailed Authentication Information: Logon Process: WDIGEST Authentication Package: WDigest Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Microsoft-Windows-Security-Auditing" Guid="{54849625-5478-4994-a5ba-3e3b0328c30d}" /> <EventID>4625</EventID> <Version>0</Version> <Level>0</Level> <Task>12544</Task> <Opcode>0</Opcode> <Keywords>0x8010000000000000</Keywords> <TimeCreated SystemTime="2010-02-19T19:47:43.890Z" /> <EventRecordID>2276316</EventRecordID> <Correlation /> <Execution ProcessID="612" ThreadID="692" /> <Channel>Security</Channel> <Computer>WEB4.net.domain.org</Computer> <Security /> </System> <EventData> <Data Name="SubjectUserSid">S-1-0-0</Data> <Data Name="SubjectUserName">-</Data> <Data Name="SubjectDomainName">-</Data> <Data Name="SubjectLogonId">0x0</Data> <Data Name="TargetUserSid">S-1-0-0</Data> <Data Name="TargetUserName">jim.lastname</Data> <Data Name="TargetDomainName">net.domain.org</Data> <Data Name="Status">0xc000006d</Data> <Data Name="FailureReason">%%2313</Data> <Data Name="SubStatus">0xc000006a</Data> <Data Name="LogonType">3</Data> <Data Name="LogonProcessName">WDIGEST</Data> <Data Name="AuthenticationPackageName">WDigest</Data> <Data Name="WorkstationName">-</Data> <Data Name="TransmittedServices">-</Data> <Data Name="LmPackageName">-</Data> <Data Name="KeyLength">0</Data> <Data Name="ProcessId">0x0</Data> <Data Name="ProcessName">-</Data> <Data Name="IpAddress">10.5.16.138</Data> <Data Name="IpPort">50065</Data> </EventData> </Event>

  Read the article

• Problems configuring nameserver in plesk

  - by Saif Bechan

  Hello, i have some troubles with setting up a nameserver in PLESK for months now. I have tried all possible scenario's but i can not get this to work. I am really in need for some help, and if you can i will really appreciate it. Basically what i want is to just set up a nameserver in PLESK. I have a primary IP, and my host gave me a secondary nameserver i can use. My host is leaseweb in the netherlands. I have made some screenshots of the important parts in my opinion, maybe you guys can see some errors in them. To use the secondary nameserver provided by leaseweb i had to enable ACL on that account, i did so and made a screenshot of that too. The DNS recursion is set to localnets. These settings have not changed for months, so the dns should be fully updated everywhere. The check i run is the following: https://www.sidn.nl/over-nl/aanvraag...-server-check/ Domeinnaam (inclusief .nl): rdshosting.nl Eerste Nameserver: ns1.rdshosting.nl Eerste IP: 62.212.66.33 Tweede Nameserver: ns7.leaseweb.net Tweede ip: 62.212.76.50 If i run the dns check of the netherlands it gives me the following errors: primary name server "ns1.rdshosting.nl." Error: specified name server is not listed as NS record. All public name servers for a domain must also be listed as NS records in the zone of the domain. This domain was specified explicitly as a name server, but not found in the zone description of the primary name server. TE.6a rdshosting.nl. 86400 IN SOA ns1.rdspartners.nl. saif2k.hotmail.com. (2010031102 12H 1H 7D 3H) Error: the MNAME in SOA says "ns1.rdspartners.nl." is the primary name server. The MNAME field in the SOA record (first parameter) lists a different primary name server from the one specified for this check. RFC1035 section 3.3.13 rdshosting.nl. 86400 IN NS ns1.rdspartners.nl. Warning: hidden name server "ns1.rdspartners.nl." never used for first contact. The zone contains an NS record for a host which is not in the list of specified name servers. Hence, this name server will not be used to initiate contact to the domain. It may be used in sequential lookups, so it may still be useful. secondary name server "ns1.rdspartners.nl." [BROKEN] [HIDDEN] Failure: name server at 77.232.85.129 cannot be reached: (unknown error) The name server could not be contacted, which may be due to temporary technical problems or global DNS configuration mistakes. The internal error is shown, but not always clear about the cause. secondary name server "ns7.leaseweb.net." Info: name server looks correctly configured. I have the content of the file etc/named.conf also: // $Id: named.conf,v 1.1.1.1 2001/10/15 07:44:36 kap Exp $ // // Refer to the named(8) man page for details. If you are ever going // to setup a primary server, make sure you've understood the hairy // details of how DNS is working. Even with simple mistakes, you can // break connectivity for affected parties, or cause huge amount of // useless Internet traffic. options { allow-recursion { localnets; }; directory "/var"; auth-nxdomain no; pid-file "/var/run/named/named.pid"; // In addition to the "forwarders" clause, you can force your name // server to never initiate queries of its own, but always ask its // forwarders only, by enabling the following line: // // forward only; // If you've got a DNS server around at your upstream provider, enter // its IP address here, and enable the line below. This will make you // benefit from its cache, thus reduce overall DNS traffic in the Internet. /* forwarders { 127.0.0.1; }; */ /* * If there is a firewall between you and nameservers you want * to talk to, you might need to uncomment the query-source * directive below. Previous versions of BIND always asked * questions using port 53, but BIND 8.1 uses an unprivileged * port by default. */ // query-source address * port 53; /* * If running in a sandbox, you may have to specify a different * location for the dumpfile. */ // dump-file "s/named_dump.db"; }; //Use with the following in named.conf, adjusting the allow list as needed: key "rndc-key" { algorithm hmac-md5; secret "CeMgS23y0oWE20nyv0x40Q=="; }; controls { inet 127.0.0.1 port 953 allow { 127.0.0.1; } keys { "rndc-key"; }; }; // Note: the following will be supported in a future release. /* host { any; } { topology { 127.0.0.0/8; }; }; */ // Setting up secondaries is way easier and the rough picture for this // is explained below. // // If you enable a local name server, don't forget to enter 127.0.0.1 // into your /etc/resolv.conf so this server will be queried first. // Also, make sure to enable it in /etc/rc.conf. zone "." { type hint; file "named.root"; }; zone "0.0.127.IN-ADDR.ARPA" { type master; file "localhost.rev"; }; // NB: Do not use the IP addresses below, they are faked, and only // serve demonstration/documentation purposes! // // Example secondary config entries. It can be convenient to become // a secondary at least for the zone where your own domain is in. Ask // your network administrator for the IP address of the responsible // primary. // // Never forget to include the reverse lookup (IN-ADDR.ARPA) zone! // (This is the first bytes of the respective IP address, in reverse // order, with ".IN-ADDR.ARPA" appended.) // // Before starting to setup a primary zone, better make sure you fully // understand how DNS and BIND works, however. There are sometimes // unobvious pitfalls. Setting up a secondary is comparably simpler. // // NB: Don't blindly enable the examples below. :-) Use actual names // and addresses instead. // // NOTE!!! FreeBSD runs bind in a sandbox (see named_flags in rc.conf). // The directory containing the secondary zones must be write accessible // to bind. The following sequence is suggested: // // mkdir /etc/namedb/s // chown bind.bind /etc/namedb/s // chmod 750 /etc/namedb/s zone "rdshosting.nl" { type master; file "rdshosting.nl"; allow-transfer { 77.232.85.129; 62.212.76.50; common-allow-transfer; }; }; zone "66.212.62.in-addr.arpa" { type master; file "66.212.62.in-addr.arpa"; allow-transfer { common-allow-transfer; }; }; acl common-allow-transfer { 62.212.76.50; }; As i mentioned i made some screenshots of some parts: First the dns settings in plesk: http://www.freeimagehosting.net/uploads/2480faed5e.jpg Second the acl settings in plesk: http://www.freeimagehosting.net/uploads/777f5e69b0.jpg Third my settings at leaseweb: http://www.freeimagehosting.net/uploads/de7122b19c.jpg And last the secondary nameserver settings from leaseweb: http://www.freeimagehosting.net/uploads/fd1da38a8f.jpg If someone has anysuggestion at all on this this will be highly appriciated. Thank you for your time! PS. I am dutch so dutch answers are welcome aswell

  Read the article

• Using pfSense, OpenVPN Connects but Still Can't See the Network

  - by nicorellius

  I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

  Read the article

• Network Logon Issues with Group Policy and Network

  - by bobloki

  I am gravely in need of your help and assistance. We have a problem with our logon and startup to our Windows 7 Enterprise system. We have more than 3000 Windows Desktops situated in roughly 20+ buildings around campus. Almost every computer on campus has the problem that I will be describing. I have spent over one month peering over etl files from Windows Performance Analyzer (A great product) and hundreds of thousands of event logs. I come to you today humbled that I could not figure this out. The problem as simply put our logon times are extremely long. An average first time logon is roughly 2-10 minutes depending on the software installed. All computers are Windows 7, the oldest computers being 5 years old. Startup times on various computers range from good (1-2 minutes) to very bad (5-60). Our second time logons range from 30 seconds to 4 minutes. We have a gigabit connection between each computer on the network. We have 5 domain controllers which also double as our DNS servers. Initial testing led us to believe that this was a software problem. So I spent a few days testing machines only to find inconsistent results from the etl files from xperfview. Each subset of computers on campus had a different subset of software issues, none seeming to interfere with logon just startup. So I started looking at our group policy and located some very interesting event ID’s. Group Policy 1129: The processing of Group Policy failed because of lack of network connectivity to a domain controller. Group Policy 1055: The processing of Group Policy failed. Windows could not resolve the computer name. This could be caused by one of more of the following: a) Name Resolution failure on the current domain controller. b) Active Directory Replication Latency (an account created on another domain controller has not replicated to the current domain controller). NETLOGON 5719 : This computer was not able to set up a secure session with a domain controller in domain OURDOMAIN due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. E1kexpress 27: Intel®82567LM-3 Gigabit Network Connection – Network link is disconnected. NetBT 4300 – The driver could not be created. WMI 10 - Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. More or less with timestamps it becomes apparent that the network maybe the issue. 1:25:57 - Group Policy is trying to discover the domain controller information 1:25:57 - The network link has been disconnected 1:25:58 - The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has successfully processed. If you do not see a success message for several hours, then contact your administrator. 1:25:58 - Making LDAP calls to connect and bind to active directory. DC1.ourdomain.edu 1:25:58 - Call failed after 0 milliseconds. 1:25:58 - Forcing rediscovery of domain controller details. 1:25:58 - Group policy failed to discover the domain controller in 1030 milliseconds 1:25:58 - Periodic policy processing failed for computer OURDOMAIN\%name%$ in 1 seconds. 1:25:59 - A network link has been established at 1Gbps at full duplex 1:26:00 - The network link has been disconnected 1:26:02 - NtpClient was unable to set a domain peer to use as a time source because of discovery error. NtpClient will try again in 3473457 minutes and DOUBLE THE REATTEMPT INTERVAL thereafter. 1:26:05 - A network link has been established at 1Gbps at full duplex 1:26:08 - Name resolution for the name %Name% timed out after none of the configured DNS servers responded. 1:26:10 – The TCP/IP NetBIOS Helper service entered the running state. 1:26:11 - The time provider NtpClient is currently receiving valid time data at dc4.ourdomain.edu 1:26:14 – User Logon Notification for Customer Experience Improvement Program 1:26:15 - Group Policy received the notification Logon from Winlogon for session 1. 1:26:15 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4. ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:18 - Computer details: Computer role : 2 Network name : (Blank) 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:19 - The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. 1:26:46 - The Network Connections service entered the running state. 1:27:10 – Retrieved account information 1:27:10 – The system call to get account information completed. 1:27:10 - Starting policy processing due to network state change for computer OURDOMAIN\%name%$ 1:27:10 – Network state change detected 1:27:10 - Making system call to get account information. 1:27:11 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:27:13 - Computer details: Computer role : 2 Network name : ourdomain.edu (Now not blank) 1:27:13 - Group Policy successfully discovered the Domain Controller in 2886 milliseconds. 1:27:13 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu The call completed in 2371 milliseconds. 1:27:15 - Estimated network bandwidth on one of the connections: 0 kbps. 1:27:15 - Estimated network bandwidth on one of the connections: 8545 kbps. 1:27:15 - A fast link was detected. The Estimated bandwidth is 8545 kbps. The slow link threshold is 500 kbps. 1:27:17 – Powershell - Engine state is changed from Available to Stopped. 1:27:20 - Completed Group Policy Local Users and Groups Extension Processing in 4539 milliseconds. 1:27:25 - Completed Group Policy Scheduled Tasks Extension Processing in 5210 milliseconds. 1:27:27 - Completed Group Policy Registry Extension Processing in 1529 milliseconds. 1:27:27 - Completed policy processing due to network state change for computer OURDOMAIN\%name%$ in 16 seconds. 1:27:27 – The Group Policy settings for the computer were processed successfully. There were no changes detected since the last successful processing of Group Policy. Any help would be appreciated. Please ask for any relevant information and it will be provided as soon as possible.

  Read the article

• straight to grub prompt on boot

  - by cheshirekow

  I am very lost. I did a fresh install of Ubuntu 10.04 on a laptop. First reboot was fine. I ran all the recommended upgrades, and now every time I start I get just a grub>_ prompt. No error message, just the prompt, and a little banner at the top saying grub's version and telling me that I have minimal bash style editing. I've tried: 1) Re-installing grub via sudo grub-install sda (There is only one disk with only two partitions, one primary, and one for swap) 2) Changed GRUB_HIDDEN_TIMEOUT=10 GRUB_TIMEOUT=30 GRUB_CMDLINE_LINUX_DEFAULT="rootdelay=90" GRUB_CMDLINE_LINUX="rootdelay=90" in /etc/default/grub. No luck. I can boot with the following: grub> set root=(hd0,1) grub> probe (hd0,1) -u c00fadde-f7e8-45e7-a4da-0235605f756 grub> linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235605f756 rootdelay=90 grub> initrd /boot/initrd.img-2.6.32-21-generic grub> boot And then everything seems to be fine from there. From the grub prompt if I try configfile /boot/grub/grub.cfg The screen clears and I get another grub prompt. So, seriously, what could the problem be? edit: Full text of /boot/grub/grub.cfg # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then load_env fi set default="0" if [ ${prev_saved_entry} ]; then set saved_entry=${prev_saved_entry} save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z ${boot_once} ]; then saved_entry=${chosen} save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n ${have_grubenv} ]; then if [ -z ${boot_once} ]; then save_env recordfail; fi; fi } insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=30 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro rootdelay=90 rootdelay=90 initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=c00fadde-f7e8-45e7-a4da-0235c605f756 ro single rootdelay=90 echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set c00fadde-f7e8-45e7-a4da-0235c605f756 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ ${timeout} != -1 ]; then if sleep --verbose --interruptible 10 ; then set timeout=0 fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### output of update-grub Generating grub.cfg ... Found linux image: /boot/vmlinuz-2.6.32-21-generic Found initrd image: /boot/initrd.img-2.6.32-21-generic Found memtest86+ image: /boot/memtest86+.bin done contents of /boot total 14280 -rw-r--r-- 1 root root 640617 2010-04-16 09:01 abi-2.6.32-21-generic -rw-r--r-- 1 root root 115847 2010-04-16 09:01 config-2.6.32-21-generic drwxr-xr-x 3 root root 4096 2010-09-08 02:42 grub -rw-r--r-- 1 root root 7968754 2010-09-02 01:49 initrd.img-2.6.32-21-generic -rw-r--r-- 1 root root 160280 2010-03-23 05:37 memtest86+.bin -rw-r--r-- 1 root root 1687378 2010-04-16 09:01 System.map-2.6.32-21-generic -rw-r--r-- 1 root root 1196 2010-04-16 09:03 vmcoreinfo-2.6.32-21-generic -rw-r--r-- 1 root root 4029792 2010-04-16 09:01 vmlinuz-2.6.32-21-generic

  Read the article

• DRBD Not syncing between my nodes

  - by Mike Curry

  Some version info: Operating system is Ubuntu 11.10, on EC2, kernel is 3.0.0-16-virtual and the application info is: Version: 8.3.11 (api:88) GIT-hash: 0de839cee13a4160eed6037c4bddd066645e23c5 build by buildd@allspice, 2011-07-05 19:51:07 Getting some strange errors in dmesg (seen below) as well, there is no replication happening. I have made my first node primary and its showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Primary/Unknown UpToDate/DUnknown r----s ext3 my secondary node is showing: drbd driver loaded OK; device status: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 m:res cs ro ds p mounted fstype 0:r0 StandAlone Secondary/Unknown Inconsistent/DUnknown r----s Showing /proc/drbd on the master shows: version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Primary/Unknown ds:UpToDate/DUnknown r----s ns:0 nr:0 dw:4 dr:1073 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Showing /proc/drbd on the slave shows that there is nothing being transfered... version: 8.3.11 (api:88/proto:86-96) srcversion: DA5A13F16DE6553FC7CE9B2 0: cs:StandAlone ro:Secondary/Unknown ds:Inconsistent/DUnknown r----s ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:262135964 Here is my config... resource r0 { protocol C; startup { wfc-timeout 15; degr-wfc-timeout 60; } net { cram-hmac-alg sha1; shared-secret "test123; } on drbd01 { device /dev/drbd0; disk /dev/xvdm; address 23.XX.XX.XX:7788; # blocked out ip meta-disk internal; } on drbd02 { device /dev/drbd0; disk /dev/xvdm; address 184.XX.XX.XX:7788; #blocked out ip meta-disk internal; } } I have run the following on the master: sudo drbdadm -- --overwrite-data-of-peer primary all There is no firewall between the systems. Here is the dmesg with some errors: [2285172.969955] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96) [2285172.969960] drbd: srcversion: DA5A13F16DE6553FC7CE9B2 [2285172.969962] drbd: registered as block device major 147 [2285172.969965] drbd: minor_table @ 0xffff88000276ea00 [2285173.000952] block drbd0: Starting worker thread (from drbdsetup [1300]) [2285173.003971] block drbd0: disk( Diskless -> Attaching ) [2285173.006150] block drbd0: No usable activity log found. [2285173.006154] block drbd0: Method to ensure write ordering: flush [2285173.006158] block drbd0: max BIO size = 4096 [2285173.006165] block drbd0: drbd_bm_resize called with capacity == 524271928 [2285173.008512] block drbd0: resync bitmap: bits=65533991 words=1023969 pages=2000 [2285173.008518] block drbd0: size = 250 GB (262135964 KB) [2285173.079566] block drbd0: bitmap READ of 2000 pages took 17 jiffies [2285173.081189] block drbd0: recounting of set bits took additional 1 jiffies [2285173.081194] block drbd0: 250 GB (65533991 bits) marked out-of-sync by on disk bit-map. [2285173.081203] block drbd0: Suspended AL updates [2285173.081210] block drbd0: disk( Attaching -> UpToDate ) [2285173.081214] block drbd0: attached to UUIDs 1C1291D39584C1D1:0000000000000004:0000000000000000:0000000000000000 [2285173.095016] block drbd0: conn( StandAlone -> Unconnected ) [2285173.095046] block drbd0: Starting receiver thread (from drbd0_worker [1301]) [2285173.099297] block drbd0: receiver (re)started [2285173.099304] block drbd0: conn( Unconnected -> WFConnection ) [2285173.099330] block drbd0: bind before connect failed, err = -99 [2285173.099346] block drbd0: conn( WFConnection -> Disconnecting ) [2285173.295788] block drbd0: Discarding network configuration. [2285173.295815] block drbd0: Connection closed [2285173.295826] block drbd0: conn( Disconnecting -> StandAlone ) [2285173.295840] block drbd0: receiver terminated [2285173.295844] block drbd0: Terminating drbd0_receiver Edit: Reading some other similar issues, it was suggested to do a 'drbdadm dump all', so I figured it couldn't hurt. ubuntu@drbd01:~$ drbdadm dump all /etc/drbd.conf:19: in resource r0, on drbd01: IP 23.XX.XX.XX not found on this host. and on slave: root@drbd02:~# drbdadm dump all /etc/drbd.conf:25: in resource r0, on drbd02: IP 184.XX.XX.XX not found on this host. Strange it doesn't find its own ip, however, this is an Amazon EC2 system using an elastic IP... here are my ipconfigs for both... master: ubuntu@drbd01:~$ ifconfig eth0 Link encap:Ethernet HWaddr 22:00:0a:1c:27:11 inet addr:10.28.39.17 Bcast:10.28.39.63 Mask:255.255.255.192 inet6 addr: fe80::2000:aff:fe1c:2711/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1569 errors:0 dropped:0 overruns:0 frame:0 TX packets:1169 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:124409 (124.4 KB) TX bytes:213601 (213.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) slave: root@drbd02:~# ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3f:00:14:9d inet addr:10.160.27.107 Bcast:10.160.27.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3fff:fe00:149d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:915 errors:0 dropped:0 overruns:0 frame:0 TX packets:774 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:75381 (75.3 KB) TX bytes:109673 (109.6 KB) Interrupt:26 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• Network Logon Issues with Group Policy and Network

  - by bobloki

  I am gravely in need of your help and assistance. We have a problem with our logon and startup to our Windows 7 Enterprise system. We have more than 3000 Windows Desktops situated in roughly 20+ buildings around campus. Almost every computer on campus has the problem that I will be describing. I have spent over one month peering over etl files from Windows Performance Analyzer (A great product) and hundreds of thousands of event logs. I come to you today humbled that I could not figure this out. The problem as simply put our logon times are extremely long. An average first time logon is roughly 2-10 minutes depending on the software installed. All computers are Windows 7, the oldest computers being 5 years old. Startup times on various computers range from good (1-2 minutes) to very bad (5-60). Our second time logons range from 30 seconds to 4 minutes. We have a gigabit connection between each computer on the network. We have 5 domain controllers which also double as our DNS servers. Initial testing led us to believe that this was a software problem. So I spent a few days testing machines only to find inconsistent results from the etl files from xperfview. Each subset of computers on campus had a different subset of software issues, none seeming to interfere with logon just startup. So I started looking at our group policy and located some very interesting event ID’s. Group Policy 1129: The processing of Group Policy failed because of lack of network connectivity to a domain controller. Group Policy 1055: The processing of Group Policy failed. Windows could not resolve the computer name. This could be caused by one of more of the following: a) Name Resolution failure on the current domain controller. b) Active Directory Replication Latency (an account created on another domain controller has not replicated to the current domain controller). NETLOGON 5719 : This computer was not able to set up a secure session with a domain controller in domain OURDOMAIN due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. E1kexpress 27: Intel®82567LM-3 Gigabit Network Connection – Network link is disconnected. NetBT 4300 – The driver could not be created. WMI 10 - Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. More or less with timestamps it becomes apparent that the network maybe the issue. 1:25:57 - Group Policy is trying to discover the domain controller information 1:25:57 - The network link has been disconnected 1:25:58 - The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has successfully processed. If you do not see a success message for several hours, then contact your administrator. 1:25:58 - Making LDAP calls to connect and bind to active directory. DC1.ourdomain.edu 1:25:58 - Call failed after 0 milliseconds. 1:25:58 - Forcing rediscovery of domain controller details. 1:25:58 - Group policy failed to discover the domain controller in 1030 milliseconds 1:25:58 - Periodic policy processing failed for computer OURDOMAIN\%name%$ in 1 seconds. 1:25:59 - A network link has been established at 1Gbps at full duplex 1:26:00 - The network link has been disconnected 1:26:02 - NtpClient was unable to set a domain peer to use as a time source because of discovery error. NtpClient will try again in 3473457 minutes and DOUBLE THE REATTEMPT INTERVAL thereafter. 1:26:05 - A network link has been established at 1Gbps at full duplex 1:26:08 - Name resolution for the name %Name% timed out after none of the configured DNS servers responded. 1:26:10 – The TCP/IP NetBIOS Helper service entered the running state. 1:26:11 - The time provider NtpClient is currently receiving valid time data at dc4.ourdomain.edu 1:26:14 – User Logon Notification for Customer Experience Improvement Program 1:26:15 - Group Policy received the notification Logon from Winlogon for session 1. 1:26:15 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4. ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:18 - Computer details: Computer role : 2 Network name : (Blank) 1:26:18 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu. The call completed in 2309 milliseconds. 1:26:18 - Group Policy successfully discovered the Domain Controller in 2918 milliseconds. 1:26:19 - The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. 1:26:46 - The Network Connections service entered the running state. 1:27:10 – Retrieved account information 1:27:10 – The system call to get account information completed. 1:27:10 - Starting policy processing due to network state change for computer OURDOMAIN\%name%$ 1:27:10 – Network state change detected 1:27:10 - Making system call to get account information. 1:27:11 - Making LDAP calls to connect and bind to Active Directory. dc4.ourdomain.edu 1:27:13 - Computer details: Computer role : 2 Network name : ourdomain.edu (Now not blank) 1:27:13 - Group Policy successfully discovered the Domain Controller in 2886 milliseconds. 1:27:13 - The LDAP call to connect and bind to Active Directory completed. dc4.ourdomain.edu The call completed in 2371 milliseconds. 1:27:15 - Estimated network bandwidth on one of the connections: 0 kbps. 1:27:15 - Estimated network bandwidth on one of the connections: 8545 kbps. 1:27:15 - A fast link was detected. The Estimated bandwidth is 8545 kbps. The slow link threshold is 500 kbps. 1:27:17 – Powershell - Engine state is changed from Available to Stopped. 1:27:20 - Completed Group Policy Local Users and Groups Extension Processing in 4539 milliseconds. 1:27:25 - Completed Group Policy Scheduled Tasks Extension Processing in 5210 milliseconds. 1:27:27 - Completed Group Policy Registry Extension Processing in 1529 milliseconds. 1:27:27 - Completed policy processing due to network state change for computer OURDOMAIN\%name%$ in 16 seconds. 1:27:27 – The Group Policy settings for the computer were processed successfully. There were no changes detected since the last successful processing of Group Policy. Any help would be appreciated. Please ask for any relevant information and it will be provided as soon as possible.

  Read the article

• Unable to SSH into EC2 instance on Fedora 17

  - by abhishek

  I did following steps But I am not able to SSH to it(Same steps work fine on Fedora 14 image). I am getting Permission denied (publickey,gssapi-keyex,gssapi-with-mic) I created new instance using fedora 17 amazon community image(ami-2ea50247). I copied my ssh keys under /home/usertest/.ssh/ after creating a usertest I have SELINUX=disabled here is Debug info: $ ssh -vvv ec2-54-243-101-41.compute-1.amazonaws.com ssh -vvv ec2-54-243-101-41.compute-1.amazonaws.com OpenSSH_5.2p1, OpenSSL 1.0.0b-fips 16 Nov 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to ec2-54-243-101-41.compute-1.amazonaws.com [54.243.101.41] port 22. debug1: Connection established. debug1: identity file /home/usertest/.ssh/identity type -1 debug1: identity file /home/usertest/.ssh/id_rsa type -1 debug3: Not a RSA1 key file /home/usertest/.ssh/id_dsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'Proc-Type:' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'DEK-Info:' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/usertest/.ssh/id_dsa type 2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 131/256 debug2: bits set: 506/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /home/usertest/.ssh/known_hosts debug3: check_host_in_hostfile: match line 17 debug3: check_host_in_hostfile: filename /home/usertest/.ssh/known_hosts debug3: check_host_in_hostfile: match line 17 debug1: Host 'ec2-54-243-101-41.compute-1.amazonaws.com' is known and matches the RSA host key. debug1: Found key in /home/usertest/.ssh/known_hosts:17 debug2: bits set: 500/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/usertest/.ssh/identity ((nil)) debug2: key: /home/usertest/.ssh/id_rsa ((nil)) debug2: key: /home/usertest/.ssh/id_dsa (0x7f904b5ae260) debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug3: start over, passed a different list publickey,gssapi-keyex,gssapi-with-mic debug3: preferred gssapi-with-mic,publickey,keyboard-interactive,password debug3: authmethod_lookup gssapi-with-mic debug3: remaining preferred: publickey,keyboard-interactive,password debug3: authmethod_is_enabled gssapi-with-mic debug1: Next authentication method: gssapi-with-mic debug3: Trying to reverse map address 54.243.101.41. debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_500' not found debug1: Unspecified GSS failure. Minor code may provide more information debug2: we did not send a packet, disable method debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/usertest/.ssh/identity debug3: no such identity: /home/usertest/.ssh/identity debug1: Trying private key: /home/usertest/.ssh/id_rsa debug3: no such identity: /home/usertest/.ssh/id_rsa debug1: Offering public key: /home/usertest/.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug2: we did not send a packet, disable method debug1: No more authentication methods to try. Permission denied (publickey,gssapi-keyex,gssapi-with-mic).

  Read the article

• Debian apt dependency mismatch (libc6)

  - by Sean Gordon

  Earlier, I tried to install package via apt-get (cython), but it failed with the Errors were encountered while processing: message, and since then, apt is refusing to install anything. apt-get check output below: root@dix:~# apt-get check Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies: libc6 : Depends: libc-bin (= 2.11.3-2) but 2.11.3-4 is installed libc6-dev : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed libc6-i386 : Depends: libc6 (= 2.11.3-4) but 2.11.3-2 is installed E: Unmet dependencies. Try using -f. Apt/aptitude don't seem to be able to fix this dependency issue, and I don't know what to do. Edit: Running apt-get -f install results in no change, and my sources are all squeeze. Running apt-get update then apt-get dist-upgrade show no change either. Edit 2: I went back to try this again in a new terminal and apt-get -f install gives this error: dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) configured to not write apport reports Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Edit 3: Using apt-get clean first, then the previous commands, results in the first error again. Using apt-get -f dist-upgrade gives the below. Reading package lists... Building dependency tree... Reading state information... Correcting dependencies... Done The following packages will be upgraded: apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common at automake base-files bind9 bind9-doc bind9-host bind9utils debian-archive-keyring dnsutils dpkg-dev file host initscripts isc-dhcp-client isc-dhcp-common krb5-multidev libapr1 libbind9-60 libc6 libdns69 libdpkg-perl libexpat1 libexpat1-dev libgc1c2 libgssapi-krb5-2 libgssrpc4 libisc62 libisccc60 libisccfg62 libk5crypto3 libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5-dev libkrb5support0 liblwres60 libmagic1 libmysqlclient16 libnss3-1d libssl-dev libssl0.9.8 libtiff4 libtiff4-dev libtiffxx0c2 libxi6 libxml2 linux-libc-dev lwresd mysql-client-5.1 mysql-common mysql-server mysql-server-5.1 mysql-server-core-5.1 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssh-client openssh-server openssl procps python python-crypto python-minimal sudo sysv-rc sysvinit sysvinit-utils tzdata tzdata-java 75 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 5 not fully installed or removed. Need to get 0 B/79.9 MB of archives. After this operation, 1,411 kB of additional disk space will be used. (Reading database ... 52241 files and directories currently installed.) Preparing to replace libc6 2.11.3-2 (using .../libc6_2.11.3-4_amd64.deb) ... *** stack smashing detected ***: /usr/bin/perl terminated ======= Backtrace: ========= /lib/libc.so.6(__fortify_fail+0x37)[0x7fdaad9b9f87] /lib/libc.so.6(__fortify_fail+0x0)[0x7fdaad9b9f50] /usr/lib/libperl.so.5.10(Perl_yylex+0x5896)[0x7fdaae343346] [0x8e83a0] ======= Memory map: ======== 00400000-00402000 r-xp 00000000 08:01 525338 /usr/bin/perl 00601000-00602000 rw-p 00001000 08:01 525338 /usr/bin/perl 00602000-0091f000 rw-p 00000000 00:00 0 [heap] 7fdaaca54000-7fdaaca6a000 r-xp 00000000 08:01 393818 /lib/libgcc_s.so.1 7fdaaca6a000-7fdaacc69000 ---p 00016000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc69000-7fdaacc6a000 rw-p 00015000 08:01 393818 /lib/libgcc_s.so.1 7fdaacc6a000-7fdaacc6f000 r-xp 00000000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaacc6f000-7fdaace6e000 ---p 00005000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6e000-7fdaace6f000 rw-p 00004000 08:01 524949 /usr/lib/perl5/auto/Locale/gettext/gettext.so 7fdaace6f000-7fdaace79000 r-xp 00000000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaace79000-7fdaad078000 ---p 0000a000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad078000-7fdaad079000 rw-p 00009000 08:01 532753 /usr/lib/perl/5.10.1/auto/Encode/Encode.so 7fdaad079000-7fdaad07e000 r-xp 00000000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad07e000-7fdaad27d000 ---p 00005000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27d000-7fdaad27e000 rw-p 00004000 08:01 525444 /usr/lib/perl/5.10.1/auto/IO/IO.so 7fdaad27e000-7fdaad299000 r-xp 00000000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad299000-7fdaad498000 ---p 0001b000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad498000-7fdaad49b000 rw-p 0001a000 08:01 525450 /usr/lib/perl/5.10.1/auto/POSIX/POSIX.so 7fdaad49b000-7fdaad49e000 r-xp 00000000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad49e000-7fdaad69e000 ---p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69e000-7fdaad69f000 rw-p 00003000 08:01 525436 /usr/lib/perl/5.10.1/auto/Fcntl/Fcntl.so 7fdaad69f000-7fdaad6a7000 r-xp 00000000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad6a7000-7fdaad8a6000 ---p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a6000-7fdaad8a7000 r--p 00007000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a7000-7fdaad8a8000 rw-p 00008000 08:01 393824 /lib/libcrypt-2.11.3.so 7fdaad8a8000-7fdaad8d6000 rw-p 00000000 00:00 0 7fdaad8d6000-7fdaada2f000 r-xp 00000000 08:01 393822 /lib/libc-2.11.3.so 7fdaada2f000-7fdaadc2e000 ---p 00159000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc2e000-7fdaadc32000 r--p 00158000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc32000-7fdaadc33000 rw-p 0015c000 08:01 393822 /lib/libc-2.11.3.so 7fdaadc33000-7fdaadc38000 rw-p 00000000 00:00 0 7fdaadc38000-7fdaadc4f000 r-xp 00000000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaadc4f000-7fdaade4e000 ---p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4e000-7fdaade4f000 r--p 00016000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade4f000-7fdaade50000 rw-p 00017000 08:01 393248 /lib/libpthread-2.11.3.so 7fdaade50000-7fdaade54000 rw-p 00000000 00:00 0 7fdaade54000-7fdaaded4000 r-xp 00000000 08:01 393826 /lib/libm-2.11.3.so 7fdaaded4000-7fdaae0d4000 ---p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d4000-7fdaae0d5000 r--p 00080000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d5000-7fdaae0d6000 rw-p 00081000 08:01 393826 /lib/libm-2.11.3.so 7fdaae0d6000-7fdaae0d8000 r-xp 00000000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae0d8000-7fdaae2d8000 ---p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d8000-7fdaae2d9000 r--p 00002000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2d9000-7fdaae2da000 rw-p 00003000 08:01 393825 /lib/libdl-2.11.3.so 7fdaae2da000-7fdaae43f000 r-xp 00000000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae43f000-7fdaae63e000 ---p 00165000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae63e000-7fdaae647000 rw-p 00164000 08:01 525387 /usr/lib/libperl.so.5.10.1 7fdaae647000-7fdaae665000 r-xp 00000000 08:01 393819 /lib/ld-2.11.3.so 7fdaae854000-7fdaae859000 rw-p 00000000 00:00 0 7fdaae862000-7fdaae864000 rw-p 00000000 00:00 0 7fdaae864000-7fdaae865000 r--p 0001d000 08:01 393819 /lib/ld-2.11.3.so 7fdaae865000-7fdaae866000 rw-p 0001e000 08:01 393819 /lib/ld-2.11.3.so 7fdaae866000-7fdaae867000 rw-p 00000000 00:00 0 7fff9616d000-7fff9618e000 rw-p 00000000 00:00 0 [stack] 7fff961ff000-7fff96200000 r-xp 00000000 00:00 0 [vdso] ffffffffff600000-ffffffffff601000 r--p 00000000 00:00 0 [vsyscall] dpkg: error processing /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb (--unpack): subprocess new pre-installation script killed by signal (Aborted) Errors were encountered while processing: /var/cache/apt/archives/libc6_2.11.3-4_amd64.deb

  Read the article

• Strategy for using snapshots to back up Ubuntu Linux server?

  - by MountainX

  I need some backup advice for my home file server. Here are the mount points, volume groups, logical volumes and used/total space of all the volumes on my Ubuntu 8.10 home file server. / vgA/lvRoot [7.5G/50G] /tmp vgB/lvTmp [195M/30G] /var vgB/lvVar [780M/30G] swap vgB/lvSwap [16.00 GB] /media1 vgC/lvMedia1 [400G/975G] /media2 vgC/lvMedia2 [75G/295G] /boot partition (no volume group) [95M/200M] /video partition (no volume group) [450G/950G] /backups vgD/lvBackupTarget [800G/925G] /home vgE/lvHome [85G/200G] I have just added a 2.0 TB external USB drive that I would like to use to backup everything. (It will be a close fit to get it all on one 2.0 TB drive. I actually have a 2nd external USB drive if needed.) I'd like to backup "/", var, /media1, media2 and /home. I'll deal with /boot and /video separately since they are not logical volumes. For all the logical volumes I'm anticipating taking snapshots and then copying those snapshots to the 2.0 TB external USB drive. I have never done a task like that before. If I do that, I could use the tutorial I found here: http://www.howtoforge.com/linux_lvm_snapshots My questions are: What is the best overall strategy? Is it LVM snapshots, as I'm assuming? How should I prepare, subdivide and mount the 2.0 TB external USB drive? 2.a. Should I create one or more regular partitions or should I create a physical volume with one or more logical volumes? 2.b. Would it be advisable to extactly mirror the source pv/lv layout on the external drive, and if so, is this a good strategy? What's the best way to get the snapshots onto the external drive? dd? Even though this is a strategy question, feedback with actual commands is appreciated. I need step-by-step cookbook-style help because I don't do much server admin work. (Background: This is a home file server that I have rarely had to touch in about 2 years. It has done its job without much intervention. The really old PC that I used to back everything up recently failed, so I'm replacing that with the external USB drive(s) and I'd like to upgrade my backup strategy at the same time. Previously, I just copied stuff from /backups over to the other computer and that would not have made things very easy in a real restore situation. The /backups mount point contains backup copies of "most" of the important data on a file by file basis, but it does not contain copies of /boot, etc. BTW, the actual internal HDD that holds /backups is separate from the other storage devices.) EDIT: I'll propose a strategy... The idea came from a comment here: LVM mirroring VS RAID1 "LVM mirrors are for replication of a logical volume to a different physical volume. It's essentially meant to "move the data to a different disk". The mirror is then broken..." That would fit my requirements well. Here is an ideal situation: establish the LV mirror on the external drive break the link with the mirror create a (persistent) snapshot on the mirror after a week, resync the mirror with the original source and update the mirror break the link and create another snapshot on the mirror. Obviously, the mirror will be like a weekly full backup. And the snapshots on the mirror will represent earlier points in time. If this would work and if it would be time efficient, it would give a nice full & differential type backup on the external drive based on LVM. I have not heard of a strategy like this before. Will it work? Could it be scripted? Thoughts? EDIT 2: Creating Portable DiskSafes With LoopbackFS And LVM Snapshots This article seems intriguing: http://www.howtoforge.com/creating-portable-disksafes-with-loopbackfs-and-lvm-snapshots Unfortunately, I don't understand exactly how to map those ideas to the strategy I'm proposing above. I'm going to ask this last bit as a separate question. I will leave my original question in place because I still desire feedback on the overall best strategy. At this moment I'm assuming it is LVM mirroring in the style of "Creating Portable DiskSafes with LVM Snapshots" but that might be wrong.

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• How to share internet over VPN and inside a virtual machine (Windows)?

  - by mountrix

  ` My final goal is to have a virtual machine at work in which anything that happen inside (tcp, udp, ping, ...) will use the Internet connection of a computer at home. So, if inside this VM should I open an Internet browser to a site such as "show my IP", my home IP should be printed. I am also looking for a way to debug/develop a software inside this VM, but I would like to tunnel only the connections of this software, not the full graphical interface, this is why a Remote Desktop solution won't fit me. The connection between the both computer should be secured somehow, like in a SSH tunnel. This ultimately should allow me to have a portable VM in which I can connect to whatever networks I have access at home, in a secure way. This is my configuration: At work, I have a LAN-connected desktop computer, with Windows 7 Professional Edition as a host [computer W] On this same computer, I have a Virtual Box machine running Windows XP [computer V] At home, I have a laptop computer, running Windows 7 Home Edition [computer H] This laptop is connected to a Livebox 2 broadband modem by Wifi. What I am trying to do is to sit at work in front of the virtual machine [V], and connect to a webpage as if the request was issued from the laptop [H] at home, and the data should be securely tunneled between the both. But if I am using internet directly inside [W], it should use the normal LAN interface at work. To achieve my goal, I first try using VPN, than SSH tunneling, without success. I first tried to install Teamviewer between [W] and [H]. This is working fine, I can send files, share desktop, etc. Teamviewer has a VPN mode that creates a new VPN network interface with its own IP, both on computer [W] and [H]. This allowed me to connect [H] as a network computer inside [W] and I was able to share files, but not to share Internet. At this point, I tried to use from [W] the Internet as if I was at home. I setup a route (using route add from command line in [W]) in order to instruct each packet going to a given website to pass by the new VPN interface on [W], with the hope it will be forwarded to [H], but the webpage was simply inaccessible. I then tried to setup a Windows VPN connection between [W] and [H], using the Windows 7 VPN feature. [H] was the server and [W] the client. But it failed: I got the "Unable to join a remote PC while trying to VPN" 720 Error when I was setting up the client on [W]. I think the problem is the Livebox 2 that could blocks the packets. But I am not sure of this: 1) with Teamviewer it works fine, 2) Livebox 2 has a configuration page for port mapping that gives the proper configuration to map VPN ports as an example so I guess that it should allow it, 3) I opened the ports 1723 (TCP) and 500 (UDP) according to some forums. Virtual box has a network configuration parameter in which I can use the VPN network interface created by Teamviewer as a bridged connection. This is suppose to work in the sense that all packets issued by the virtual machine [V] is supposed to go directly to [H]. But I had no internet connection inside [V]. Using the NAT mode, [V] has internet. For me this is the feature that I look for: filtering all connections from the virtual box application to the VPN network interface, and the remaining should use the normal LAN interface. Apart from the build-in feature of VBox, I even do not know if it is possible to route the packet from a given application to a given interface. Finally I tried also SSH tunneling, but this is not the solution I looked for. Using an external SSH server (Linux), I was able to create a localhost connection on [W] (or [V]), using something like 'ssh -N -D server[H]' in order to allow a web browser located in [W] to connect to any website using the SOCKS 5 proxy created locally (SOCKS is a build-in feature of SSH). But repeating the same operation on windows, using a windows SSH server inside [W] (I tried freeSSHd), it failed: SFTP worked, but not the SOCKS tunneling, it was like the browser in [H] did not find internet. Finally only Teamviewer looked able to create a VPN between [W] and [H], but I am not able to use it, as I want, I mean using the Internet connection of [H] sitting in front of [W]. I also tried to bridge the VPN interface and the wifi interface inside [H], but it blocked my laptop, and I tried also the Internet Connection Sharing, trying to share on [H] the wifi connection over the VPN interface. This fails also, but it seems because Teamviewer actually use the wifi interface to be able to provide the VPN link, so I guess I am creating a recursive loop. I do not know what to try next... Thank you for any advice!!

  Read the article

• squid3 auth thru samba using ntlm to AD doesn't work

  - by derty

  some users here are spending to much time exploring the WWW. So big boss whats to get this under control. We use a squid3 just for some security reason and chace benefits. and now i'm trying to set up a new proxy on a different server (Debian 6) Permissions are defined in AC and the squid3 should get the auth thru samba/winbind by using the ntlm protocol. but i'll get all the time Access, denited. it only works by using LDAP but thats not the way i need it. here some log and confs squid access.log 1326878095.784 1 192.168.15.27 TCP_DENIED/407 4049 GET http://at.msn.com/? -NONE/- text/html 1326878095.791 1 192.168.15.27 TCP_DENIED/407 4294 GET http://at.msn.com/? - NONE/- text/html 1326878095.803 9 192.168.15.27 TCP_DENIED/403 4028 GET http://at.msn.com/? kavan NONE/- text/html 1326878095.848 0 192.168.15.27 TCP_DENIED/403 3881 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878100.279 0 192.168.15.27 TCP_DENIED/403 3735 GET http://www.google.at/ kavan NONE/- text/html 1326878100.296 0 192.168.15.27 TCP_DENIED/403 3870 GET http://www.squid-cache.org/Artwork/SN.png kavan NONE/- text/html 1326878155.700 0 192.168.15.27 TCP_DENIED/407 4072 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.705 2 192.168.15.27 TCP_DENIED/407 4317 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml - NONE/- text/html 1326878155.709 3 192.168.15.27 TCP_DENIED/403 4026 GET http://ie9cvlist.ie.microsoft.com/IE9CompatViewList.xml kavan NONE/- text/html squid chace 2012/01/18 10:12:49| Creating Swap Directories 2012/01/18 10:12:49| Starting Squid Cache version 3.1.6 for x86_64-pc-linux-gnu... 2012/01/18 10:12:49| Process ID 17236 2012/01/18 10:12:49| With 65535 file descriptors available 2012/01/18 10:12:49| Initializing IP Cache... 2012/01/18 10:12:49| DNS Socket created at [::], FD 7 2012/01/18 10:12:49| DNS Socket created at 0.0.0.0, FD 8 2012/01/18 10:12:49| Adding nameserver 192.168.15.2 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.19 from /etc/resolv.conf 2012/01/18 10:12:49| Adding nameserver 192.168.15.1 from /etc/resolv.conf 2012/01/18 10:12:49| Adding domain schoenbrunn.local from /etc/resolv.conf 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'ntlm_auth' processes 2012/01/18 10:12:49| helperOpenServers: Starting 10/10 'squid_kerb_auth' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| helperOpenServers: Starting 5/5 'squid_ldap_group' processes 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| squid_kerb_auth: INFO: Starting version 1.0.5 2012/01/18 10:12:49| Unlinkd pipe opened on FD 73 2012/01/18 10:12:49| Local cache digest enabled; rebuild/rewrite every 3600/3600 sec 2012/01/18 10:12:49| Store logging disabled 2012/01/18 10:12:49| Swap maxSize 0 + 262144 KB, estimated 20164 objects 2012/01/18 10:12:49| Target number of buckets: 1008 2012/01/18 10:12:49| Using 8192 Store buckets 2012/01/18 10:12:49| Max Mem size: 262144 KB 2012/01/18 10:12:49| Max Swap size: 0 KB 2012/01/18 10:12:49| Using Least Load store dir selection 2012/01/18 10:12:49| Set Current Directory to /var/spool/squid3 2012/01/18 10:12:49| Loaded Icons. 2012/01/18 10:12:49| Accepting HTTP connections at [::]:3128, FD 74. 2012/01/18 10:12:49| HTCP Disabled. 2012/01/18 10:12:49| Squid modules loaded: 0 2012/01/18 10:12:49| Adaptation support is off. 2012/01/18 10:12:49| Ready to serve requests. 2012/01/18 10:12:50| storeLateRelease: released 0 objects smb.conf # Domain Authntication Settings workgroup = <WORKGROUP> security = ads password server = <DOMAINNAME>.LOCAL realm = <DOMAINNAME>.LOCAL ldap ssl = no # logging log level = 5 max log size = 50 # logs split per machine log file = /var/log/samba/%m.log # max 50KB per log file, then rotate ; max log size = 50 # User settings username map = /etc/samba/smbusers idmap uid = 10000-20000000 idmap gid = 10000-20000000 idmap backend = ad ; template primary group = <ad group> template shell = /sbin/nologin # Winbind Settings winbind separator = + winbind enum users = Yes winbind enum groups = Yes winbind netsted groups = Yes winbind nested groups = Yes winbind cache time = 10 winbind use default domain = Yes #Other Globals unix charset = LOCALE server string = <SERVERNAME> load printers = no printing = cups cups options = raw ; printcap name = /etc/printcap #obtain list of printers automatically on SystemV ; printcap name = lpstat ; printing = cups squid.conf auth_param ntlm program /usr/bin/ntlm_auth --require-membership-of=<DOMAINNAME>\\INTERNETZ --helper-protocol=squid-2.5-ntlmssp auth_param ntlm children 10 auth_param basic program /usr/lib/squid3/squid_ldap_auth -R -b "dc=<dcname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f sAMAccountName=%s -h 192.168.15.19:3268 auth_param basic realm "Proxy Authentifizierung. Bitte geben Sie Ihren Benutzername und Ihr Passwort ein!" #means insert you PW in an other language - # external_acl_type InetGroup %LOGIN /usr/lib/squid3/squid_ldap_group -R -b "dc=<domainname>,dc=local" -D "cn=administrator,cn=Users,dc=<domainname>,dc=local" -w "******" -f "(&(objectclass=person)(sAMAccountName=%v) (memberof=cn=%a,cn=internetz,dc=<domainname>,dc=local))" -h 192.168.15.19:3268 auth_param negotiate program /usr/lib/squid3/squid_kerb_auth -d auth_param negotiate children 10 auth_param negotiate keep_alive on acl localnet proxy_auth REQUIRED acl InetAccess external InetGroup Internetz http_access allow InetAccess http_access deny all acl auth proxy_auth REQUIRED http_access allow auth and a very suspicious is that by adding the proxy server to the Domain i see 2 new entries in the PC one with the original computer-name leopoldine and one with leopoldine CNF:f8efa4c4-ff0e-4217-939d-f1523b43464d ?!? I tried a lot, really... but i stuck on this problem... i actually i even reinstalled all dependent programs and reconfigured them from default. Group exists and has me in it. Firefox running on the old proxy and i use IE for testing the new one. But i'll get all the time Access-Denited and to be honest i'm quite a beginner, so please don't be to prude. I'll interested in improving, i'll get the information we need to fix this but i started working 2 month ago and got only 1 1/2 year's training and not a single sec. in linux ;)

  Read the article

• Performance required to improve Windows Experience Index?

  - by Ian Boyd

  Is there a guide on the metrics required to obtain a certain Windows Experience Index? A Microsoft guy said in January 2009: On the matter of transparency, it is indeed our plan to disclose in great detail how the scores are calculated, what the tests attempt to measure, why, and how they map to realistic scenarios and usage patterns. Has that amount of transparency happened? Is there a technet article somewhere? If my score was limited by my Memory subscore of 5.9. A nieve person would suggest: Buy a faster RAM Which is wrong of course. From the Windows help: If your computer has a 64-bit central processing unit (CPU) and 4 gigabytes (GB) or less random access memory (RAM), then the Memory (RAM) subscore for your computer will have a maximum of 5.9. You can buy the fastest, overclocked, liquid-cooled, DDR5 RAM on the planet; you'll still have a maximum Memory subscore of 5.9. So in general the knee-jerk advice "buy better stuff" is not helpful. What i am looking for is attributes required to achieve a certain score, or move beyond a current limitation. The information i've been able to compile so far, chiefly from 3 Windows blog entries, and an article: Memory subscore Score Conditions ======= ================================ 1.0 < 256 MB 2.0 < 500 MB 2.9 <= 512 MB 3.5 < 704 MB 3.9 < 944 MB 4.5 <= 1.5 GB 5.9 < 4.0GB-64MB on a 64-bit OS Windows Vista highest score 7.9 Windows 7 highest score Graphics Subscore Score Conditions ======= ====================== 1.0 doesn't support DX9 1.9 doesn't support WDDM 4.9 does not support Pixel Shader 3.0 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 7.9 Windows 7 highest score Gaming graphics subscore Score Result ======= ============================= 1.0 doesn't support D3D 2.0 supports D3D9, DX9 and WDDM 5.9 doesn't support DX10 or WDDM1.1 Windows Vista highest score 6.0-6.9 good framerates (e.g. 40-50fps) at normal resoltuions (e.g. 1280x1024) 7.0-7.9 even higher framerates at even higher resolutions 7.9 Windows 7 highest score Processor subscore Score Conditions ======= ========================================================================== 5.9 Windows Vista highest score 6.0-6.9 many quad core processors will be able to score in the high 6 low 7 ranges 7.0+ many quad core processors will be able to score in the high 6 low 7 ranges 7.9 8-core systems will be able to approach 8.9 Windows 7 highest score Primary hard disk subscore (note) Score Conditions ======= ======================================== 1.9 Limit for pathological drives that stop responding when pending writes 2.0 Limit for pathological drives that stop responding when pending writes 2.9 Limit for pathological drives that stop responding when pending writes 3.0 Limit for pathological drives that stop responding when pending writes 5.9 highest you're likely to see without SSD Windows Vista highest score 7.9 Windows 7 highest score Bonus Chatter You can find your WEI detailed test results in: C:\Windows\Performance\WinSAT\DataStore e.g. 2011-11-06 01.00.19.482 Disk.Assessment (Recent).WinSAT.xml <WinSAT> <WinSPR> <DiskScore>5.9</DiskScore> </WinSPR> <Metrics> <DiskMetrics> <AvgThroughput units="MB/s" score="6.4" ioSize="65536" kind="Sequential Read">89.95188</AvgThroughput> <AvgThroughput units="MB/s" score="4.0" ioSize="16384" kind="Random Read">1.58000</AvgThroughput> <Responsiveness Reason="UnableToAssess" Kind="Cap">TRUE</Responsiveness> </DiskMetrics> </Metrics> </WinSAT> Pre-emptive snarky comment: "WEI is useless, it has no relation to reality" Fine, how do i increase my hard-drive's random I/O throughput? Update - Amount of memory limits rating Some people don't believe Microsoft's statement that having less than 4GB of RAM on a 64-bit edition of Windows doesn't limit the rating to 5.9: And from xxx.Formal.Assessment (Recent).WinSAT.xml: <WinSPR> <LimitsApplied> <MemoryScore> <LimitApplied Friendly="Physical memory available to the OS is less than 4.0GB-64MB on a 64-bit OS : limit mem score to 5.9" Relation="LT">4227858432</LimitApplied> </MemoryScore> </LimitsApplied> </WinSPR> References Windows Vista Team Blog: Windows Experience Index: An In-Depth Look Understand and improve your computer's performance in Windows Vista Engineering Windows 7 Blog: Engineering the Windows 7 “Windows Experience Index”

  Read the article

• Deployment Workbench no longer available after PXE boot

  - by Patrick

  Our build process revolves around windows Deployment Workbench. Unfortunately this was setup by someone who is no longer with the company, and no-one has ever dared/needed to make any changes. The other day it stopped working. It turns out that one of our build guys started thinking about changing some stuff in it, clicked something and now it no longer works (He is saying now that he right clicked on the 'LAB' entry in 'Deployment points' and hit 'Update', which took some time to run through apparently). The job has fallen on me to resolve and frankly I'm not sure what I'm doing. I was wondering if someone with more experience than me can provide some pointers as to troubleshooting cos I'm feeling quite a lot in the dark here. On the server I have Deployment Workbench up and running (MMC snapin) version 3.0. There is a WDS service that appears to be running ok, as does the tFTPd service. Nothing specific to this in event logs. From the client side; PXE boot works and gets you to the Win PE launch, and it has the correct company logo as the background (proving to me that its loading win PE from the network). WPEINIT runs, and asks for domain credentials, here the team simply put User/Pass/Domain in the boxes and click ok. Normally the build would kick off. Instead they get an error message saying that the \NATBLU01\Distribution$ share isn't available. Checking \NATBLU01\Distribution$ shows that its there and accessible over the network. Security/permissions seem ok, even 'ANONYMOUS LOGON' has read access to that share so I don't see that being a problem. Digging the trace files from C:\MININT\SMSOSD\OSDLOGS\ after an attempt to run the build I can see an error saying much the same - <![LOG[Validating connection to \\NATBLU01\Distribution$]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[FindFile: The file OSDConnectToUNC.exe could not be found in any standard locations.]LOG]!><time="16:42:14.000+000" date="03-15-2012" component="LiteTouch" context="" type="1" thread="" file="LiteTouch"> <![LOG[The network location cannot be reached. For information about network troubleshooting, see Windows Help.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> <![LOG[ERROR - Unable to map a network drive to \\NATBLU01\Distribution$.]LOG]!><time="16:42:24.000+000" date="03-15-2012" component="LiteTouch" context="" type="3" thread="" file="LiteTouch"> BDD.LOG shows much the same. Full copies of the .LOG files can both files be found here : BDD.LOG LITETOUCH.LOG I can get to a command prompt from the Win PE that boots from PXE, however there isn't any network stuff there. IPCONFIG returns nothing so none of the tests I would usually run resolve anything. I'm at a loss frankly. I did wonder if I could perhaps start a new build process but if the change to the DeploymentWorkbench has knocked it offline I don't think I'm going to be able to create a new deployment. Failing that; we do have a deployment point labeled type 'Media' which appears to be a DVD ISO image of one of the builds, but its dated 2008, is it possible to export the network build to .ISO and build from DVD? We are looking at new hardware to run this from anyway (for the impending Windows 7 roll out) so a temporary work round isn't going to be too much of a problem. All assistance is appreciated! EDIT : OK. Got it working again. Solution was close to Newmanth's idea. The problem was that our PE image didn't appear to be connecting the network. I had an older copy of the PE boot.WIM on a stick that I had been using for other purposes. I booted that and correctly got a network connection. Showed a correct internal IP and could ping out etc etc. However I was still getting the same errors in all the logs and in when wpeinit was running. What I did seperately was to update the PE image that DeploymentWorkbench was pushing out to display a different back ground. I wanted to prove that I was working in the correct place. Turns out that I wasn't. I went and looked at the other deployment stuff we had on this machine, Windows Deployment Services was installed and although all the install images are off line the boot image was online, so I uploaded the copy from my stick to that. Booted straight off. And fixed. Working. Yay! For anyone stumbling across this in the future you may find that although your deployment images are located in the DeploymentWorkbench, the Win PE boot image you are launching from is located in the associated Windows Deployment Services images.

  Read the article

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• rsync over ssh is not working anymore, while ssh itself is working fine (Write failed: broken pipe)

  - by brazorf

  This issue started happening after i changed router. This is the scenario: Windows7 Host Ubuntu 10.04 Guest (VirtualBox) Ubuntu 10.04 remote server What i used to do is run a very basic rsync command: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory This worked perfect until i did change adsl provider, and i changed router aswell: now, this happens: rsync on Ubuntu Guest is not working anymore (to any random server), if using this new router rsync on Ubuntu Guest is WORKING, if i switch back to old router i tried a new virtual box ubuntu install, and the command is WORKING with both the routers So, the not-working-combo is oldUbuntu + newRouter. To get things worst, i can state that (on the not-working ubuntu) i ping the remote host plain ssh connection to the remote host is working fine (i can auth, connect, and do stuff on the remote host) scp is NOT working (this is just a further thing i tried) This is the console output of the execution, with ssh verbose set to vvvv: root@client:~# rsync -ae 'ssh -vvvv' /root/test-rsync/ {username}@{hostname}:/home/{username}/test/ OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /root/.ssh/config debug1: Applying options for {hostname} debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to {hostname} [{ip.add.re.ss}] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug3: Not a RSA1 key file /root/.ssh/{private_key}. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /root/.ssh/{private_key} type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debian-3ubuntu7 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu7 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug3: Wrote 792 bytes for a total of 831 debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 [email protected] debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 [email protected] debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug3: Wrote 24 bytes for a total of 855 debug2: dh_gen_key: priv key bits set: 125/256 debug2: bits set: 525/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: Wrote 144 bytes for a total of 999 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 4 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 5 debug1: Host '{hostname}' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:4 debug2: bits set: 512/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/{private_key} (0x7f3ad0e7f9b0) debug3: Wrote 80 bytes for a total of 1143 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /root/.ssh/{private_key} debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1511 debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: fp 1b:65:36:92:59:b3:12:3e:8c:c6:03:28:d4:81:09:dc debug3: sign_and_send_pubkey debug1: read PEM private key done: type RSA debug3: Wrote 656 bytes for a total of 2167 debug1: Enabling compression at level 6. debug1: Authentication succeeded (publickey). debug2: fd 4 setting O_NONBLOCK debug3: fd 5 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug3: Wrote 112 bytes for a total of 2279 debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending environment. debug3: Ignored env TERM debug3: Ignored env SHELL debug3: Ignored env SSH_CLIENT debug3: Ignored env SSH_TTY debug1: Sending env LC_ALL = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env MAIL debug3: Ignored env PATH debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env SHLVL debug3: Ignored env HOME debug3: Ignored env LANGUAGE debug3: Ignored env LOGNAME debug3: Ignored env SSH_CONNECTION debug3: Ignored env LESSOPEN debug3: Ignored env LESSCLOSE debug3: Ignored env _ debug1: Sending command: rsync --server -logDtpre.iLsf . /home/{username}/test/ debug2: channel 0: request exec confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug3: Wrote 208 bytes for a total of 2487 At this point everything freeze for lots of minutes, ending in Write failed: Broken pipe rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: unexplained error (code 255) at io.c(601) [sender=3.0.7] Any suggestion? Thank You F. Edit 2012/09/13: i am changing title and issue definition, since i made some TINY step ahead and i think i can give more detailed clues.

  Read the article

• What needs updating when moving a bootable Windows 7 (or Vista) partition?

  - by SuperTempel

  When I move a bootable NTFS partition with Windows on it to a different block offset, what needs updating to make it bootable again? In particular, here's what I tried: I have a disk with several partitions, one of which is the NTFS partition with Windows on it, and the disk uses the plain old MBR block 0 for the partitions layout (no more than 4 partitions). Now I format and partition a new, larger, disk. There I make room for the NTFS partition and copy the contents from the old disk's NTFS Windows partition into. And I make the partition "active". However, when I try to boot from this disk, I get a "read error" message immediately and the booting stops, the exact text is: A disk read error occurred Press Ctrl+Alt+Del to restart I verified that both disks have the same boot sector code in block 0. It seems to me that something else might need updating. I guess that somewhere there's a absolute block reference that I need to update, probably pointing to the next level loader or to the NT kernel. Update: I found this article going quite into the depth of what I want to know. However, it says to modify boot.ini, but I have Windows 7 installed here, where such things appear to have changed: No boot.ini but a folder called System Volume Information with GUID and other data in it that sounds related to my problem. Going to keep digging... Update 2: Thanks to the terrible looking but very informative website by starman, I was able to figure out the first step: The NTFS boot sector has a field for "hidden" sectors. This feld has to contain the sector number of the boot sector. This solves the "read error" message. Now, however, I get a "BOOTMGR is missing" error instead. Looks like there's another place where a block number has to be adjusted, but I can't find anything in the code listing about this. I do find a lot of help sites suggesting Windows tools for fixing this "BOOTMGR is missing" problem, but none seem to know what goes on behind the scenes. Kind of like suggesting to re-install Windows when there's a little problem with it. At least, those fixes seem to work, mostly involving the Bcdedit and Bootrec tools. Now, who knows what they do, especially the latter, in regards to a moved partition? Update 3: After lots of trial-and-error attempts, I believe now that the solution lies in the BCD-Template registry file, residing usually inside \Windows\System32\config. If I get this updated using the "bcdboot" command, Windows starts up from it. I am now in the middle of figuring out what information this registry contains relevant to the above question. Any pointers to the contents of this registry are welcome. Update 4: Turns out that while the BCD-Template file gets rewritten and has different binary contents than its predecessor, the values inside do not change. So it must be something else that bcdboot.exe writes. I had previously already checked if it changes the first 32 boot blocks of the partition, but they appear to remain unchanged. Parititon map doesn't get changed, either. So what is it that bcdboot modifies besides the BCD registry? Any tips on how I can trace that? Are there low level tools that show me what files a program writes to? Update 5: The answer seems to be: c:\Boot\BCD is also changed, and that appears to be the key file for the boot manager's process. I'll investigate this later... Update 6: It seems to be an important detail that I had originally two partitions created when I installed Windows 7: A small partition of 204800 sectors which appears to be a bootstrap partition, followed by the actual, large, partition containing the Windows system (drive C:). When I tried to transfer this installation to a new, larger, disk, I had kept the same two partitions intact on the new drive, although they ended up at a different offset. This alone led to the "BOOTMGR is missing" message. Since then, I've used bcdboot.exe only on the Windows partition, which added the \Boot\BCD file on that partition. That file (and folder) did originally only exist on the smaller partition. Hence, this problem may be more complicated in my case as one partition (the boot strapper) referred to another partition (the one containing the OS), whereas other people may only have to deal with one partition containing both, and maybe there the solution is simpler. Update 7: Found one more detail: The \Boot\BCD file records the MBR's serial number. If that number doesn't match, the system won't boot. Next I'll test if there's also an absolute block reference stored in there.

  Read the article

• dynatree: how can i select child node programmatically

  - by Muhammad Adeel Zahid

  hello everyone i m using jquery's dynaTree in my application and i want to select the all the child nodes programmably when a node is selected. the structure of my tree is as follows <div id = "tree"> <ul> <li>package 1 <ul> <li>module 1.1 <ul> <li> document 1.1.1</li> <li> document 1.1.2</li> </ul> </li> <li>module 1.2 <ul> <li>document 1.2.1</li> <li>document 1.2.2</li> </ul> </li> </ul> </li> <li> package 2 <ul> <li> module 2.1 <ul> <li>document 2.1.1</li> <li>document 2.1.1</li> </ul> </li> </ul> </li> </ul> </div> now what i want is that when i click on tree node with title "package 1" all its child nodes i.e (module 1.1, document 1.1.1, document 1.1.2, module 1.2, document 1.2.1, document 1.2.2) should also be selected below is the approach i tried to use $("#tree").dynatree({ onSelect: function(flag, dtnode) { // This will happen each time a check box is selected/deselected var selectedNodes = dtnode.tree.getSelectedNodes(); var selectedKeys = $.map(selectedNodes, function(node) { //alert(node.data.key); return node.data.key; }); // Set the hidden input field's value to the selected items $('#SelectedItems').val(selectedKeys.join(",")); if (flag) { child = dtnode.childList; alert(child.length); for (i = 0; i < child.length; i++) { var x = child[i].select(true); alert(i); } } }, checkbox: true, onActivate: function(dtnode) { //alert("You activated " + dtnode.data.key); } }); in the if(flag) condition i get all the child nodes of element that is selected by user and it gives me the correct value that i can see from alert(child.length) statement. then i run the loop to select all the children but loop never goes beyond the statement var x = child[i].select(true); and i can never see the statement alert(i) being executed. the result of above statement is that if i select package 1, module 1.1 and document 1.1.1 is also selected but never does it execute alert(i) statement neither other children of package 1 are selected. in my view when first time child[i].select(true) statement is executed it also triggers the on select event of its children thus making a recursion kind of thing is my thinking correct? no matter recursion or what why on earth does it not complete the loop and execute very next instruction alert(i). please help me in solving this problem. i m dying to see that alert any suggestion and help is highly appriciated thanks Adeel

  Read the article

• Best practices for using the Entity Framework with WPF DataBinding

  - by Ken Smith

  I'm in the process of building my first real WPF application (i.e., the first intended to be used by someone besides me), and I'm still wrapping my head around the best way to do things in WPF. It's a fairly simple data access application using the still-fairly-new Entity Framework, but I haven't been able to find a lot of guidance online for the best way to use these two technologies (WPF and EF) together. So I thought I'd toss out how I'm approaching it, and see if anyone has any better suggestions. I'm using the Entity Framework with SQL Server 2008. The EF strikes me as both much more complicated than it needs to be, and not yet mature, but Linq-to-SQL is apparently dead, so I might as well use the technology that MS seems to be focusing on. This is a simple application, so I haven't (yet) seen fit to build a separate data layer around it. When I want to get at data, I use fairly simple Linq-to-Entity queries, usually straight from my code-behind, e.g.: var families = from family in entities.Family.Include("Person") orderby family.PrimaryLastName, family.Tag select family; Linq-to-Entity queries return an IOrderedQueryable result, which doesn't automatically reflect changes in the underlying data, e.g., if I add a new record via code to the entity data model, the existence of this new record is not automatically reflected in the various controls referencing the Linq query. Consequently, I'm throwing the results of these queries into an ObservableCollection, to capture underlying data changes: familyOC = new ObservableCollection<Family>(families.ToList()); I then map the ObservableCollection to a CollectionViewSource, so that I can get filtering, sorting, etc., without having to return to the database. familyCVS.Source = familyOC; familyCVS.View.Filter = new Predicate<object>(ApplyFamilyFilter); familyCVS.View.SortDescriptions.Add(new System.ComponentModel.SortDescription("PrimaryLastName", System.ComponentModel.ListSortDirection.Ascending)); familyCVS.View.SortDescriptions.Add(new System.ComponentModel.SortDescription("Tag", System.ComponentModel.ListSortDirection.Ascending)); I then bind the various controls and what-not to that CollectionViewSource: <ListBox DockPanel.Dock="Bottom" Margin="5,5,5,5" Name="familyList" ItemsSource="{Binding Source={StaticResource familyCVS}, Path=., Mode=TwoWay}" IsSynchronizedWithCurrentItem="True" ItemTemplate="{StaticResource familyTemplate}" SelectionChanged="familyList_SelectionChanged" /> When I need to add or delete records/objects, I manually do so from both the entity data model, and the ObservableCollection: private void DeletePerson(Person person) { entities.DeleteObject(person); entities.SaveChanges(); personOC.Remove(person); } I'm generally using StackPanel and DockPanel controls to position elements. Sometimes I'll use a Grid, but it seems hard to maintain: if you want to add a new row to the top of your grid, you have to touch every control directly hosted by the grid to tell it to use a new line. Uggh. (Microsoft has never really seemed to get the DRY concept.) I almost never use the VS WPF designer to add, modify or position controls. The WPF designer that comes with VS is sort of vaguely helpful to see what your form is going to look like, but even then, well, not really, especially if you're using data templates that aren't binding to data that's available at design time. If I need to edit my XAML, I take it like a man and do it manually. Most of my real code is in C# rather than XAML. As I've mentioned elsewhere, entirely aside from the fact that I'm not yet used to "thinking" in it, XAML strikes me as a clunky, ugly language, that also happens to come with poor designer and intellisense support, and that can't be debugged. Uggh. Consequently, whenever I can see clearly how to do something in C# code-behind that I can't easily see how to do in XAML, I do it in C#, with no apologies. There's been plenty written about how it's a good practice to almost never use code-behind in WPF page (say, for event-handling), but so far at least, that makes no sense to me whatsoever. Why should I do something in an ugly, clunky language with god-awful syntax, an astonishingly bad editor, and virtually no type safety, when I can use a nice, clean language like C# that has a world-class editor, near-perfect intellisense, and unparalleled type safety? So that's where I'm at. Any suggestions? Am I missing any big parts of this? Anything that I should really think about doing differently?

  Read the article

• Parsing GeoRSS Feed with jQuery

  - by senfo

  I'm attempting to use the jQuery jFeed plugin for parsing an Atom, GeoRSS feed and I'm running into issues extracting the information I need. For example, I need to extract the summary element and I would like to render the contents in a div on my HTML page. Additionally, I'd like to extract the contents from the georss:point elements and pass them into Google Maps to render them as points on a map. The problem is that it seems jFeed is stripping out the GeoRSS-related information. For example, I can extract the title element without issues, but it seems it doesn't extract the summary or georss:point elements, at all. Following is a snippet of the XML I'm working with: <feed xmlns="http://www.w3.org/2005/Atom" xmlns:georss="http://www.georss.org/georss"> <title>Search Results from DataWarehouse.HRSA.gov</title> <link rel="self" href="http://datawarehouse.hrsa.gov/HGDWDataWebService/HGDWDataService.aspx?service=HC&zip=20002&radius=10"/> <link rel="alternate" href="http://datawarehouse.hrsa.gov/"/> <author> <name>HRSA Geospatial Data Warehouse</name> </author> <id>tag:datawarehouse.hrsa.gov,2010-04-05:/</id> <updated>2010-04-05T19:25:28-05:00</updated> <entry> <title>Christ House</title> <link href="http://www.christhouse.org" /> <id>tag:datawarehouse.hrsa.gov,2010-04-05:/D388C4C6-FFA4-4091-819B-64D67DC64931</id> <summary type="xhtml"> <div xmlns="http://www.w3.org/1999/xhtml"> <div class="vcard"> <div class="fn org">Christ House</div> <div class="adr"> <div class="street-address">1717 Columbia Rd. N.W.</div> <span class="locality">Washington</span>, <span class="region">District of Columbia</span>, <span class="postal-code">20009-2803</span> </div> <div class="tel">202-328-1100</div> </div> <div> Categories: <span class="category">Service Delivery Site</span> </div> </div> </summary> <georss:point>38.9243636363636 -77.0395636363637</georss:point> <updated>2010-04-04T00:00:00-05:00</updated> </entry> </feed> Following is the jQuery code that I'm using: $(document).ready(function() { $.getFeed({ //url: 'http://datawarehouse.hrsa.gov/HGDWDataWebService/HGDWDataService.aspx?service=HC&zip=20002&radius=10', url: 'test.xml', success: function(feed) { $.each(feed.items, function(index, value) { $('#rssContent').append(value.title); // Set breakpoint here }); } }); }); I set a breakpoint on the line that appends to the rssContent div and noticed the objects in feed.items don't have the properties I'm after. Am I doing something wrong or was jFeed simply not designed to work the way I want it to?

  Read the article

• Rails HABTM accepts_nested_attributes_for mapping table

  - by Rabbott

  Currently I have a habtm relationship between a datastream (stream), and a chart. I want to be able to use the 'typical' jquery "add new stream" method to add a new entry into a mapping table that holds the chart_id, and stream_id.. But I think that most examples out there are made to handle a one to many relationship.. The functionality provided here by Ryan Bates is what I'm looking for, But I dont want to use checkboxes, I want to use a select (drop down) to add new items to the mapping table. I need THIS and THIS combined chart.rb class Chart < ActiveRecord::Base has_and_belongs_to_many :streams, :readonly => false, :join_table => 'charts_streams' accepts_nested_attributes_for :streams, :reject_if => lambda { |a| a.values.all?(&:blank?) }, :allow_destroy => true stream.rb class Stream < ActiveRecord::Base has_and_belongs_to_many :charts, :readonly => false, :join_table => 'charts_streams' application.js /* * Method used to add new child form partials */ $('form a.add_child').click(function() { var assoc = $(this).attr('data-association'); var content = $('#' + assoc + '_fields_template').html(); var regexp = new RegExp('new_' + assoc, 'g'); var new_id = new Date().getTime(); var newElements = jQuery(content.replace(regexp, new_id)).hide(); $(this).parent().before(newElements).prev().slideFadeToggle(); return false; }); /* * Method used to remove child form partials */ $('form a.remove_child').live('click', function() { if(confirm('Are you sure?')) { var hidden_field = $(this).prev('input[type=hidden]')[0]; if(hidden_field) { hidden_field.value = '1'; } $(this).parents('.fields').slideFadeToggle(); } return false; }); _form.html.erb <div id="streams"> <h4>Streams</h4> <% form.fields_for :streams do |stream_form| %> <%= render :partial => "stream", :locals => {:f => stream_form} %> <% end %> </div> <p><%= add_child_link 'Add a stream', :streams %></p> <%= new_child_fields_template(form, :streams) %> _stream.html.erb <div class="fields"> <p> <%= f.label :stream_id %><br /> <%= select_tag "chart[stream_ids][]", options_for_select(@streams.map {|s| [s.label, s.id]}, f.object.id) %> </p> <p><%= remove_child_link 'Remove stream', f %></p> </div> This may be overkill and what I am looking to do could be much easier.. Basically when I create a chart I want to be able to add as many streams to it as I want, using the javascript for adding a new entry, and removing an old one... Thanks for the help! This is 'working' but gives me a ActiveRecord::ReadOnlyRecord error when it hits the chart.update_attributes method.. am I adding the the :readonly = false in the wrong spot? Or am I just doing it completely wrong?

  Read the article

• On REST: WADL or not IDL, is the following approach right ?

  - by redben

  This question is a bit long, please bear with me. In REST, i think we should not need WADL or any IDL. But rather something that would implicitly cover its concept. The way I think about it is when we (humans) surf the Web, when we go to a web site for the first time, we don't know what services it provides. You discover those on the html home page (or a sitemap page in a help section) or maybe just the main menu on the home page. If you make an analogy, the homepage or site map to us humans is what WSDL is to WS-* or what WADL could be to a REST service. Only that its just like any other html content. I think that in REST the following is a good way to do things, respecting the HATEOS paradigm. Have a top level (or default) resource that lists links to your other resources. For a library example, say RestLibrary.com/ it could be something like: <root xmlns:lib="http://librarystandards.com/libraryml"> <resource class="lib:book"> <link type="application/vnd.libraryml+xml" template="mylib.com/book/{isbn}" /> <link type="application/vnd.libraryml+xml" rel="add" href="mylib.com/book" method="POST" /> <link type="application/vnd.libraryml+xml" rel="update" template="mylib.com/book/{isbn}" method="PUT" /> </resource> <resource class="lib:bookList"> <link template="mylib.com/book?keywords={keywords}" type="application/vnd.openlibrary+xml" rel="search" /> </resource> </root> Note that it is assumed that the media type "application/vnd.libraryml+xml" is a defined standard or (may be just proprietary vocabulary) named libraryml. Also, the client should be able to understand this "homepage" resource (elements root, resource and link). This is the part that could be used instead of WADL : an Abstract vocabulary that should be understandable by any client. You could use an existing standard like Atom for example. But the main idea is to have an abstract vocabulary understandable by any client. Why not WADL then ? well wadl is only for service discovery. The idea here is to have an light abstract vocabulary that would serve as a base for hypermedia. A "root" vocabulary. Like in owl we have owl:thing...etc Now if the client knows the "libraryml" standard it can follow the links to the things it understands (after parsing the media type properties and xmlns). If not, it just won't. When i can't understand how to deal with something in REST architecture i tend to see how we Humans do it in the Web. In the Web, we have the Generic language that is HTML that enables site builders to deliver any specific content, regardless of its meaning to the client (the user), Browsers understand HTML but not the "meaning" of its content. It is the user that understands the (domain specific) content. If i go to say QuantumPhysics.org, my browser can render the home page (it is just html after all) and i can read the home page. If i understand quantum then fine i can continue browsing. If i don't i just get out (unless i want to learn the hardway :) ) In the RetsLibrary.com example the client app is just like me+my browser on QuantumPhysics.org. the media type "application/vnd.libraryml+xml" is quantum physics (knowledge). http is http in both examples. Now HTML of QuantumPhysics.org is in RestLibrary.com is XML + that tiny little abstract vocabulary (root resource and link, that you could replace with something like Atom). So does this approach have any value ? don't we need a root tiny hyper-vocabulary so we can succeed with hypermedia and the "initial URI" concept ? edit Yeah why not RDF as the root vocabulary !

  Read the article

• RSpec test failing looking for a new set of eyes

  - by TheDelChop

  Guys, Here my issuse: I've got two models: class User < ActiveRecord::Base # Setup accessible (or protected) attributes for your model attr_accessible :email, :username has_many :tasks end class Task < ActiveRecord::Base belongs_to :user end with this simple routes.rb file TestProj::Application.routes.draw do |map| resources :users do resources :tasks end end this schema: ActiveRecord::Schema.define(:version => 20100525021007) do create_table "tasks", :force => true do |t| t.string "name" t.integer "estimated_time" t.datetime "created_at" t.datetime "updated_at" t.integer "user_id" end create_table "users", :force => true do |t| t.string "email" t.string "password" t.string "password_confirmation" t.datetime "created_at" t.datetime "updated_at" t.string "username" end add_index "users", ["email"], :name => "index_users_on_email", :unique => true add_index "users", ["username"], :name => "index_users_on_username", :unique => true end and this controller for my tasks: class TasksController < ApplicationController before_filter :load_user def new @task = @user.tasks.new end private def load_user @user = User.find(params[:user_id]) end end Finally here is my test: require 'spec_helper' describe TasksController do before(:each) do @user = Factory(:user) @task = Factory(:task) end #GET New describe "GET New" do before(:each) do User.stub!(:find).with(@user.id.to_s).and_return(@user) @user.stub_chain(:tasks, :new).and_return(@task) end it "should return a new Task" do @user.tasks.should_receive(:new).and_return(@task) get :new, :user_id => @user.id end end end This test fails with the following output: 1) TasksController GET New should return a new Task Failure/Error: get :new, :user_id => @user.id undefined method `abstract_class?' for Object:Class # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:1234:in `class_of_active_record_descendant' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:900:in `base_class' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:655:in `reset_table_name' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:647:in `table_name' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:932:in `arel_table' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:927:in `unscoped' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/named_scope.rb:30:in `scoped' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activerecord/lib/active_record/base.rb:405:in `find' # ./app/controllers/tasks_controller.rb:15:in `load_user' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/callbacks.rb:431:in `_run__1954900289__process_action__943997142__callbacks' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/callbacks.rb:405:in `send' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/callbacks.rb:405:in `_run_process_action_callbacks' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/callbacks.rb:88:in `send' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/callbacks.rb:88:in `run_callbacks' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/abstract_controller/callbacks.rb:17:in `process_action' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/action_controller/metal/rescue.rb:8:in `process_action' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/abstract_controller/base.rb:113:in `process' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/abstract_controller/rendering.rb:39:in `sass_old_process' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/gems/haml-3.0.0.beta.3/lib/sass/plugin/rails.rb:26:in `process' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/action_controller/metal/testing.rb:12:in `process_with_new_base_test' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/action_controller/test_case.rb:390:in `process' # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/actionpack/lib/action_controller/test_case.rb:328:in `get' # ./spec/controllers/tasks_controller_spec.rb:20 # /home/chopper/.rvm/gems/ruby-1.8.7-p249@rails3/bundler/gems/rails-16a5e918a06649ffac24fd5873b875daf66212ad-master/activesupport/lib/active_support/dependencies.rb:209:in `inject' Can anybody help me understand what's going on here? It seems to be an RSpec problem since the controller action actually works, but I could be wrong. Thanks, Joe

  Read the article

< Previous Page | 446 447 448 449 450 451 452 453 454 455 456 457  | Next Page >