Search Results

Search found 16987 results on 680 pages for 'second'.

Page 456/680 | < Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >

• sysctl.conf not running on boot

  - by Brian

  At what point is sysctl.conf supposed to be read during boot, and why might it not be running? I have the following settings which are not being applied when I reboot: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 fs.nfs.nlm_udpport = 32768 fs.nfs.nlm_tcpport = 32768 The first section is needed for KVM bridging, and the second is to run the NFS lock manager on a known port. However, after booting, these values have not taken effect. If I run sysctl -p, then they do. This wouldn't be a huge issue, except that I can't figure out how to restart the lock manager without rebooting. I would really like to know why sysctl.conf isn't working at boot, but I'd settle for just being able to restart the lock manager. This is on Ubuntu server 10.04.2, kernel 2.6.32-31-server. I know some daemons check the permissions on their config files and refuse to work if they're too permissive, but sysctl.conf is 644 root:root, which I'm pretty sure is the default.

  Read the article

• Cannot 301 redirect with IIS URL Rewrite Module

  - by Justin

  I am trying to troubleshoot my issue with the URL Rewrite Module on IIS 7. I migrated a Wordpress blog over to BlogEngine.net. There were only about 5 entries that I wanted to use 301 redirects to the new blog, so I wanted to simply create 5 exact match redirect rules using the rewrite module. For some reason the exact match rule never seems to take effect, I always get a 404 error when the original url is navigated to. I verified that my exact match pattern matched the existing backlinks and it does. I then tried a simple test and got the same behavior, no redirection. I created a page, test.html, on my site, I then created a second page, test2.html. So my exact match pattern is: "http://www.mydomain.com/test.html" And the rule is supposed to do a 301 redirect to "http://www.mydomain.com/test2.html " The redirect never happens. I created the steps for the rule based on the instructions in this page: http://learn.iis.net/page.aspx/461/creating-rewrite-rules-for-the-url-rewrite-module/ I don't see that I left out a step. After I apply the rule I've even gone as far as doing an IISReset to make sure it would be in effect but still no luck. Any thoughts on what I might have left out? (Note: my rewrite rules dont include the " " around them but I had to add since serverfault thinks I am trying to spam the system with multiple urls.)

  Read the article

• Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

  - by ThaKidd

  As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

  Read the article

• Very strange networking problem in all computers in my house

  - by Anthony

  I have three computers in my house: One desktop (wired), and two laptops (wireless). I'm using Cox Communications (yes they suck), and yesterday they had a major outage. I know it was them because I called them up when I started losing connection to the internet. All the computers can connect just fine, but they don't have internet access. It just says "local only". The weird thing is, some of them work occasionally. For the first day my laptop was working perfectly, while all the other computers couldn't connect. Later on in the day it got reversed, and the desktop was the one with internet access. By the second day the problem on Cox's end was fixed, but we still had no access. I called them up and they reset my modem, and did the usual troubleshooting stuff. It never fixed the problem, but we found out that the problem had to do with conflicting IP addresses. My router was a Linksys WRT54G and it was about 5 years old. I figured it might have gotten damaged from the outage since it was so old, and now it's having trouble "fixing itself" and giving out the proper IP addresses. So I bought a new router, a Cisco Linksys E1000. I set everything up, and still the same problem. My computer has access right now (that's how I'm writing this), but no other computers seem to be able to get access. Is there possible damage to the modem? Can someone help me please? Sorry for this being so long.

  Read the article

• reverse proxy not rewriting to https

  - by polishpt

  I need your help. I'm having problems with reverse proxy rewriting to https: I have an alfresco app running on top of tomcat and as a front and an Apache server - it's site-enabled looks like that: <VirtualHost *:80> ServerName alfresco JkMount /* ajp13_worker <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature Off </VirtualHost> I also have a reverse proxy server running on second machine and i want it to rewrite queries to https. It's site-enabled looks like that: <VirtualHost 192.168.251.50:80> ServerName alfresco DocumentRoot /var/www/ RewriteEngine on RewriteRule (.*) https://alfresco/ [R] LogLevel warn ErrorLog /var/log/apache2/alfresco-80-error.log CustomLog /var/log/apache2/alfresco-80-access.log combined ServerSignature Off </VirtualHost> <VirtualHost 192.168.251.50:443> ServerName alfresco DocumentRoot /var/www/ SSLEngine On SSLProxyEngine On SSLCertificateFile /etc/ssl/certs/alfresco.pem SSLCertificateKeyFile /etc/ssl/private/alfresco.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://192.168.251.50:8080/alfresco ProxyPassReverse /alfresco http://192.168.251.50:8080/alfresco LogLevel warn ErrorLog /var/log/apache2/alfresco-443-error.log CustomLog /var/log/apache2/alfresco-443-access.log combined ServerSignature Off </VirtualHost> Now, ProxyPass works, when I go to alfresco/alfrsco in a browser application opens, but rewriting to https doesn't work. Plese help. Regards when I go to 192.168.251.50 Tomcat configuration page shows up. When I go to 192.268.251.50:8080 - the same as above when I go to 192.168.251.50:8080/alfresco - alfresco app page shows app when I go to alfresco/alfresco - same as above when i go to https://alfresco or https://alfresco i get an error connecting to a server

  Read the article

• Webservice randomly dropping connections - possibly due to firewall nonevent data?

  - by adam

  I have a hosted webapp which requests data from a REST webservice in our office. Each page calls one (or several) webservices, which go from our host, via our firewall (a Watchguard Firebox) to a server in our office. All of a sudden, the app has dramatically slowed. We have determined that the webservice is timing out at random when called externally (it's fine when called within the office network). I'm pretty certain it's our connection which is dropping the webservice call, so I've written a quick php/curl script which calls the webservice over many iterations and shows the various timings. Below is an example output, showing both a failed and a successful call (with a 5 second timeout): http_code namelookup_time connect_time pretransfer_time starttransfer_time total_time 1 0 0.000096 0.0342 0.0000 0.0000 0.0342 2 200 0.000052 0.0332 0.1327 0.1751 0.1752 As per iteration #1 above, failed requests seem to be failing between connect and pretransfer. I'm not sure if this shows that the connection is successfully past the firewall, or could the firewall still cause an issue? Our firewall is showing a series of nondata event log messages for the relevant access rule. Our IT team tells me these are routine, although I can find no mention of these in Google. I'm not sure if this fits in between connect and pretransfer. Having elinated the webservice server (by testing internally) and the live webapp (by testing different code on different external servers, I am left suspecting the connection to the office. Could the firebox nondata events be causing a problem between connect and pretransfer?

  Read the article

• Password-protected sharing allows access to users who have no account?

  - by romkyns

  Running Win7 on two computers in my LAN. Computer A has password-protected sharing enabled, and shares a folder. It has a single user account "Bob", and the Guest account is turned off. The network is workgroup-based. According to the descriptions of the "password-protected sharing" I could find, the only people who can access the shared folder via the LAN are those who know the username+password for the "Bob" account. However a second computer on the LAN is able to view this shared folder by simply browsing to Computer A. They don't need to enter any passwords or anything. The only user account registered on that PC is called "Jim", and has a different password from "Bob". How on earth is computer B able to view this shared folder? Is the popular description of the "password-protected sharing" feature inaccurate / did I misunderstand it big time? P.S. There is a possibility that the password for "Bob" has been entered on that PC once, and possibly the "remember password" box was checked. I've looked in the "Credential Manager" on both computers and there is nothing saved anywhere.

  Read the article

• Slow File Copy observed copying 40GB files across network to iSCSI device

  - by Rick

  Here's a curious ones for the gurus: Setup: Source Machine: Windows Server 2003 R2 machine with local hard drive. VHD file of 40GB. 1 x 1Gbps network card, Cat6 cable, switch. Target Machine: Windows Server 2008 R2 machine with iSCSI connection to iSCSI target on separate machine (1TB, RAID5). 1 x 1Gbps network card, Cat6 cable, connected to same switch as for Source Machine. Second 1Gbps network card, Cat6 cable, connected via isolated switch to the iSCSI target. Switches are Netgear JGS524 model (web managed). If I copy from the Win2003R2 machine to Win2008R2 machine local drive I get 40GB in 45 minutes, 36 seconds. If I copy from the Win2008R2 machine to the iSCSI target (local drive to iSCSI target) I get 40GB in 37 minutes 56 seconds. If I copy from the Win2003R2 machine to the iSCSI target via the Win2008R2 machine I get 40GB in 3 hours, 50 minutes, 24 seconds. All copies were done via the following command issued on the Win2008R2 box: XCOPY <source> <target> /J XCOPY /J - Copies using unbuffered I/O. Recommended for very large files. So, what's the bit I'm missing here? Why does a back-to-back copy take in total 1 hour, 23 minutes, 32 seconds when a "straight through" copy take almost 3 times as long? Switches show no errors, network hovers around the 3% utilisation mark for the duration of the copy (whereas the "back-to-back" copies are around the 25% utilisation mark). What have I missed?

  Read the article

• Apache server configuration name resolution (virtual host naming + security)

  - by Homunculus Reticulli

  I have just setup a minimal (hopefully secure? - comments welcome) apache website using the following configuration file: <VirtualHost *:80> ServerName foobar.com ServerAlias www.foobar.com ServerAdmin [email protected] DocumentRoot /path/to/websites/foobar/web DirectoryIndex index.php # CustomLog with format nickname LogFormat "%h %l %u %t \"%r\" %>s %b" common CustomLog "|/usr/bin/cronolog /var/log/apache2/%Y%m.foobar.access.log" common LogLevel notice ErrorLog "|/usr/bin/cronolog /var/log/apache2/%Y%m.foobar.errors.log" <Directory /> AllowOverride None Order Deny,Allow Deny from all </Directory> <Directory /path/to/websites/> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> I am able to access the website by using www.foobar.com, however when I type foobar.com, I get the error 'Server not found' - why is this? My second question concerns the security implications of the directive: <Directory /path/to/websites/> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> in the configuration above. What exactly is it doing, and is it necessary?. From my (admitedly limited) understanding of Apache configuration files, this means that anyone will be able to access (write to?) the /path/to/websites/ folder. Is my understanding correct? - and if yes, how is this not a security risk?

  Read the article

• SVNParentPath directory authorization

  - by James

  The question is a bit stupid but I can't get it sorted. I have a server with SVN that uses the SVNPath directive in httpd.conf and all works fine with path authorizations. Now I'm installing a second serer where I'm going to use SVNParentPath directive and I've got it all running except I can't get the authorization part quite right. From what I understand it's the same as when you use SVNPath but you need to specificy the repo name before the folder name.. My SVNParentPath is /srv/svn/ and I created a directory /srv/svn/testproj and then ran svnadmin create /srv/svn/testproj Now i'm configuring my authorization file: [/] * = svnadmin = rw adusgi = rw [testproj:/svn/testproj] demada = rw degari = rw scarja = rw Now if I try to commit /svn/testproj using user svnadmin or adusgi all is fine. If I try for example demada it doesn't work... (I've run the htpasswd2 commands for the user obviously. The directory is correct or atleast thats how I use the directory with the SVNPath server thats already running, the part I think I'm getting wrong is the repo name, I just used the directory name but what am I really supposed to put there?? Thank you, James

  Read the article

• 2nd instance of mysql closes/doesnt start no warnings/errors?

  - by acidzombie24

  I have an external HD and i'd like to run a 2nd mysql instance on it. I used the windows installer to install/configure mysqld as a service on windows7. I took the my.ini from C:\Program Files\MySQL\MySQL Server 5.5\my.ini Then edited the port (client and mysqld), datadir and innodb_data_home_dir. After running this command "C:\Program Files\MySQL\MySQL Server 5.5\bin\mysqld" --defaults-file="f:/dev/my.ini" I found an error which was all about the innodb_data_home_dir directory not existing. After that I ran the command again. Mysqld simply starts up for a second then immediately closes. I see no message in my command prompt. I know this command line args are correct as i see the mysqld service using the same one except a different my.ini path. Also it did tell me about the directory not existing so i know it is reading the new ini file. How do i figure out why this 2nd instance of mysqld is closing? How do i get 2 instance running? I'm using v 5.5

  Read the article

• Is there any special way to force GoBack to work with Windows Vista and 7?

  - by dfree

  Norton/Roxio's GoBack doesn't work with Vista/7 for reasons unknown. I have tried several alternatives (Norton Ghost, RollbackRX, Norton Save and Restore), none of which offer the same functionality as GoBack. Not only does GoBack not eat up all your hard drive space while creating a legitimate fail safe for any pc problems, it also allows you to see ACTIVELY EXACTLY WHAT PROCESS ARE BEING EXECUTED ON YOUR COMPUTER. This feature (called Advanced Disk Drive Restore) also allows you to troubleshoot problems and determine causes for things in about half a second by seeing what is happening on your machine. It's how I learned everything I know about computers. GoBack also features something called Safe Try Mode where you can put it in SafeTry and then mess up the whole computer and when you come out of it, your computer will be exactly how it was before. Amazing for people who like to tinker without risking their machine stability. It also helps for that accidentally erased paper or whatever you may have erased. I believe GoBack installs a type44 partition around the drive, which loads prior to windows to allow this functionality. If you're going to recommend another program, please don't (unless it does all of the above). I've tried all the competition and nothing is as good. I just want my GoBack to work with 7 :) Any ideas of crazy ways to make this work?

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Very slow browsing shared folder XP client/host

  - by Ickster

  I have a pretty straightforward setup where I'm storing media files on an XP pro machine, and sharing the folder to be accessed by other XP pro machines around the house. (Typically, there's only one client accessing the share at a time, although there may be several with the share mounted.) It's been working just fine for years, but I've recently started having some problems. A couple of days ago, the host PC had power disconnected while it was running. It was restarted and everything seemed fine initially, but since then browsing the shared folder from client machines has been extremely slow and actually reading data is all but impossible. The problem exists in every access method I've tried: Windows Explorer, VLC dialogs, command line, etc. My first thought was that the disk was experiencing problems, but there are no problems viewing the files locally on the host machine. My second thought was that there was a network problem on the host machine, so I removed and reinstalled drivers for the NIC with no change. My third thought was that there might've been a problem elsewhere on the network, so I swapped out hardware to no avail. I'm regrouping and trying to come up with a methodical approach to figuring out what might be wrong. I would of course be thrilled if you can suggest specific problems (Microsoft KB articles, etc.) that I might check, but I'm not expecting a silver bullet. If you can help me outline an approach to identify the problem (including recommended tools, e.g., disk checkers, network analyzers, etc.) I'd greatly appreciate it.

  Read the article

• Apache2/mod_fcgid/PHP Process Limits Not Respected

  - by Daniel

  I've recently moved to Apache2 / mod_fcgid / PHP from nginx / php_fpm. This is the second server on which I've made this migration, but it's used much less frequently than the first, which is working like a charm. The problem is in the PHP processes that it's spawning. In looking at the mod_fcgid documentation, it appears that the default for killing idle processes is 300 seconds; I've changed that to 20. At this point, I'd be fine if 300 would work - but it's not happening. It's been running for nearly a day now, and server-status shows 12 active processes: Process name: php5 Pid Active Idle Accesses State 19243 84879 14420 11 Ready Process name: php5 Pid Active Idle Accesses State 20954 82143 149 22 Ready 20947 82149 149 22 Ready 20953 82143 149 13 Ready Process name: php5 Pid Active Idle Accesses State 20589 82765 23644 72 Ready Process name: php5 Pid Active Idle Accesses State 17663 86103 2034 117 Ready Process name: php5 Pid Active Idle Accesses State 19862 83961 1976 91 Ready Process name: php5 Pid Active Idle Accesses State 18495 85825 5164 18 Ready Process name: php5 Pid Active Idle Accesses State 25463 75109 23948 24 Ready Process name: php5 Pid Active Idle Accesses State 2466 60019 60016 2 Ready Process name: php5 Pid Active Idle Accesses State 20729 82541 12592 23 Ready Process name: php5 Pid Active Idle Accesses State 22135 80616 46361 6 Ready PHP applications are not being served at this point - Apache is returning a 503. However, it is still serving the server-status module, and mod_mono/Mono 2.10 applications are still being served. The problem is with the PHP. /etc/apache2/mods-available/fcgid.conf... <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi FcgidConnectTimeout 10 FcgidMaxRequestsPerProcess 500 FcgidIdleTimeout 20 FcgidFixPathinfo 1 FcgidMaxProcesses 10 </IfModule> (heh - Max Processes isn't being respected either...) Of course, fcgid.conf is smylinked in mods-enabled.

  Read the article

• PowerPoint save group as picture creates asymmetric edge, how to fix?

  - by Se Norm

  I created tons of figures for my thesis in PowerPoint and now I realized that when I try to save the grouped items (= one figure) as a picture (EMF), it somehow asymmetrically adds a border on the left and the bottom. First one is original group, second is the same pasted as a picture. Original group: Pasted as a picture: Does anyone have an idea how to fix that for a huge number of figures? I think it only started happening when I used a page size of 1m x 1m in PowerPoint to be able to zoom in more for some figures. However, I cannot not simply change the page size now as it messes up font and object sizes. Also, copying it into a smaller page and then saving as EMF doesn't do the trick. Maybe it is not related to the page size after all. Cropping every figure individually would be a lot of work, so I hope there is a different solution. I found the origin of the problem: the text label in the left bottom corner of each image (0s, 8s, 16s). I still do not understand why it is happening though, since the text label does not expand over the edge of the image (it was aligned using the align left function). It would still be great if there was an easy way to fix this, especially as I want to keep the text where it is.

  Read the article

• APACHE - PHP - Bounce emails

  - by user1179459

  I want to improve our mail server lists by handling all the bounces we get in our websites. I have a website which has over 8000+ users and another website which as over 1500+ users, they are emailed various notifications every second, ie. job alerts, email alerts, I am using POP connections with EXIM on APACHE server, most scripts are based on PHP language generates email on the fly. Problems i have But some users has registered long time ago and now quite few has bounce email address Some users register with dummy emails like [email protected] which never existed but a valid email address, any chance of stopping this without asking them login to the email account and clicking links which dont work most times.. (too annoying to the end user) Server is sending unnecessary emails can be avoided if i know they dont exists ? Solutions i need to have Is there a way i can download the bounce email list somewhere (WHM/Cpanel), i know exim mail has it but its not readable (i need a file like CSV or something similar to scan them over and write a php script to delete the users from the database ?) I need to know if there is any function in the PHP that can check the existence of the email address on the fly ? so that i can set the email send function in the mailer class to check before it sends out. On the server will bouncing emails are going to eatup lots of server resources ? like memory/cpu on processing them ? or are they are minimal where we dont have to worry about this at all ? May be a opensoruce or linux software to capture them and view them in a report basis and cleaning them up ? I am not a linux expert or server admin but i do lot of PHP coding, so please be descriptive of the solutions specially if they are linux commands Thank you!

  Read the article

• Load Sharing Regarding Large Websites

  - by JHarley1

  Hello, I have a question regarding Load Sharing for large websites. My Understanding: So if you have a website that has millions of fits a day you will need to have an architecture that can support this sort of pressure. You can either do one or two things: Invest in a single large server that has huge amounts of processing power, memory and storage (such as Microsoft's TerraServer). Spread the load of your website across a number of machines. Let me tackle the second approach, so you have a collection of machines all running Web Server Software and all having access to identical copies of the websites pages. You can either spread the load across these machines using a cyclic pattern in a DNS or you can use a Load Ballancing Switch. The advantages of this approach is: - Redundancy - servers can fail and the others would "pick up the slack" - Incremental - the ability to easily add new machines to this set-up. My Question's Is there a Virtual approach to this issue of load balancing now? If the website runs from a database - is there still only a single copy of the database? If a user had a session running on one Server (e.g. they had gone to www.example.org and had been assigned to Server 2 - were they had created a session) if they refreshed the website (and were allocated Server 3) would they still have their session? What are the other disadvantages associated with Load Balancing? Many Thanks, J

  Read the article

• Redirect specific domains with DNS

  - by user66377

  Currently we filter internet content using OpenDNS, our internal Windows DC/DNS servers point to the router's DNS, which then points to the OpenDNS servers. This works well to block all computer's on the network equally. New issue. We now need to separate what computers can go to what sites. So facebook is blocked for everyone right now, but I need to open it up to the 3 community computers now. The 3 community computers will be on an untrusted network seperate from the company computers so they can have their own DNS server, from their own router. The issue is though they still must connect to the internet using the same IP address. So OpenDNS sees the same IP and blocks them the same way. We are looking into getting a second IP, but it's not likely an option without going up to the next major level with our ISP which we don't want to do. My thought is this. Can I setup a DNS server on the untrusted network, and then depending on the request that comes in, have it send it to either OpenDNS or our ISP's DNS? Example www.facebook.com and www.youtube.com are both on the OpenDNS blacklist. So if they go to www.youtube.com, the local DNS server goes to the ISP's DNS to get the IP and thus the client gets the right IP and can go to the site. This would be manually entered for each allowed site thus creating a white list. Then if they go to www.facebook.com, since the local DNS server does not find an entry, it sends the request to OpenDNS, which then sees the site is on the blacklist, and thus sends the it's blocked webpage. The local DNS server can be either Bind on Linux or MS DNS on Window 2008. If this can be done, can you give some direction as well as I've never setup a DNS such as this before. Thanks

  Read the article

• Is there any way to send Outlook meeting requests from a non-default calendar?

  - by rbeier

  Hi, We have a user with two Outlook accounts. [email protected] is of type Exchange; [email protected] is of type IMAP/SMTP. Both are actually on our Exchange server; but since an Outlook profile can only have one Exchange account, the second one is set up as IMAP. The user would like to send a meeting request from her xyz.com account, so the "from" address appears as [email protected]. Unfortunately that doesn't work. If she creates the meeting in her xyz.com calendar, the meeting request still goes out through her Exchange account, [email protected]. The meeting request "compose message" window has an Account dropdown below the Send button, but this has no effect. Before she sends the invitation, a warning appears: "Responses to this meeting request will not be tallied because this meeting is not in your main Calendar folder. Is this OK?" Is there any workaround for this? We're using Outlook 2007 and Exchange 2003 SP2. Thanks, Richard

  Read the article

• CentOS - mdadm raid1 drive won't mount to default location

  - by danny

  I'm running CentOS 5.5, the system, boot, swap, etc. is all on /dev/sda and I have two identical single-partition drives /dev/sdb1 /dev/sdc1 that are configured in RAID1 (using mdadm). It was working fine (configured to mount to /mnt/data in the fstab file) and I recently let yum install a couple of automatic updates without paying attention to what they were, and now it doesn't work. Raid is working fine (dmesg shows it gets loaded correctly). mdstat shows: # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[1] sdb1[0] XXXX blocks [2/2] [UU] unused devices: <none> Additionally, I can mount it anywhere other than its default directory (i.e. the following works, and I can read data off the drives). # mount /dev/md0 /mnt/data2 EXT3-fs warning: mounting fs with errors, running e2fsck is recommended But when I run the following I get: # mount -a mount: /dev/sdb1 already mounted or /mnt/data busy It says nothing is mounted when I try to umount /dev/sdb1 or umount /mnt/data, so I assume it's the second of those errors. However, lsof | grep mnt shows nothing. The weird thing is that I can save files in /mnt/data. So something is obviously mounted there, but when I try to umount it I get the error that nothing is mounted. /etc/mtab doesn't mention any of the partitions or files I am trying to work with, and fstab just has that one line I mentioned above that is supposed to mount my raid partition. Again, it was all working fine until I On Google I've found a few things about dmraid interfering with mdadm after an update, but I yum remove'd dmraid and rebooted and it didn't help. I'm really confused and need to get this working to get on with my work!

  Read the article

• I am under DDoS. What can I do?

  - by Falcon Momot

  This is a Canonical Question about DoS and DDoS mitigation. I found a massive traffic spike on a website that I host today; I am getting thousands of connections a second and I see I'm using all 100Mbps of my available bandwidth. Nobody can access my site because all the requests time out, and I can't even log into the server because SSH times out too! This has happened a couple times before, and each time it's lasted a couple hours and gone away on its own. Occasionally, my website has another distinct but related problem: my server's load average (which is usually around .25) rockets up to 20 or more and nobody can access my site just the same as the other case. It also goes away after a few hours. Restarting my server doesn't help; what can I do to make my site accessible again, and what is happening? Relatedly, I found once that for a day or two, every time I started my service, it got a connection from a particular IP address and then crashed. As soon as I started it up again, this happened again and it crashed again. How is that similar, and what can I do about it?

  Read the article

• Apache is spawning more and more processes!!

  - by erotsppa

  We have a LAMP setup that is working prety good for half a year. All of a sudden today the apache server (mysql servers are not on this box) started to die. It seems to have started to spawn more and more processes over time. Eventually it will consume all the memory and the server would just die. We are using prefork. In the mean time what we are doing is just added more ram and increased the MaxClients and ServerLimit parameter to 512. We're just prolonging the crash. The number still goes up slowly. Maybe in a day, it would reach that limit. What is going on? We only have around 15-20 request per second. We have 1Gb memory and it's not half used, there's no swapping going on. Why is apache creating more and more processes? It's almost like theres a leak somewhere! The database boxes are fine, they are not causing a delay to requests. We tested some queries everything is quick!

  Read the article

• Multiple Set Peer for VPN Failover

  - by Kyle Brandt

  I will have two Cisco routers at Location A serving the same internal networks, and one router in location B. Currently, I have one router in each location with a IPSec site-to-site tunnel connecting them. It looks something like: Location A: crypto map crypto-map-1 1 ipsec-isakmp description Tunnel to Location B set peer 12.12.12.12 set transform-set ESP-3DES-SHA match address internal-ips Location B: crypto map crypto-map-1 1 ipsec-isakmp description Tunnel to Location A set peer 11.11.11.11 set transform-set ESP-3DES-SHA match address internal-ips Can I achieve fail over by simply adding another set peer at location B?: Location A (New secondary Router, configuration on previous router stays the same): crypto map crypto-map-1 1 ipsec-isakmp description Tunnel to Location B set peer 12.12.12.12 set transform-set ESP-3DES-SHA match address internal-ips Location B (Configuration Changed): crypto map crypto-map-1 1 ipsec-isakmp description Tunnel to Location A set peer 11.11.11.11 ! 11.11.11.100 is the ip of the new second router at location A set peer 11.11.11.100 set transform-set ESP-3DES-SHA match address internal-ips Cisco Says: For crypto map entries created with the crypto map map-name seq-num ipsec-isakmp command, you can specify multiple peers by repeating this command. The peer that packets are actually sent to is determined by the last peer that the router heard from (received either traffic or a negotiation request from) for a given data flow. If the attempt fails with the first peer, Internet Key Exchange (IKE) tries the next peer on the crypto map list. But I don't fully understand that in the context of a failover scenerio (One of the routers as Location A blowing up).

  Read the article

• Using AT on Ubuntu to Background Downloads (w/ Queue)

  - by Nicholas Yost

  I am writing a PHP script, but I want to use the AT command in Ubuntu to fetch a remote file via WGET. I'm basically looking to background the process, so PHP can finish fairly quickly. I cannot find any questions on here about how to use both, but I basically want to do the following pseudo-code: <?php exec('at now -q queuename wget http://path.to/remote/file.ext'); ?> Additionally, I'd like to queue this between providers. I'd like to have each path.to have its own queue, so I only download one file from each provider at a time. Meaning: <?php exec('at now -q remote wget http://path.to/remote/file.ext /local/path'); exec('at now -q vendorone wget http://vendor.one/remote/file.ext /local/path'); exec('at now -q vendortwo wget http://vendor.two/remote/file.ext /local/path'); exec('at now -q vendorone wget http://vendor.one/remote/file.ext /local/path'); ?> This should download the files from path.to, vendor.one, vendor.two immediately, and when the first file is finished downloading from vendor.one, it starts the second file. Does that make sense? I can't find anything like this anywhere on the web, much less on SO/SF. If we can use the crontab to run a one-off wget command, thats fine too.

  Read the article

< Previous Page | 452 453 454 455 456 457 458 459 460 461 462 463  | Next Page >