Search Results

Search found 47090 results on 1884 pages for 'linux ubuntu customize'.

Page 46/1884 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• Can't mount hard drive. Ubuntu 12.04

  - by Sam

  I am trying to recover some pictures on my 320 GB Hard Disk, so I put in a Live Ubuntu CD and am in that right now. In the devices list, it shows my USB drive, but not my 320 GB Hard Disk. I can see the disk in Disk Utility (it says it's on /dev/sda), but it's not mounted, and it says it has a few bad sectors but it is OK. In Disk Usage Analyzer, it says my maximum capacity is 13.4 GB, so it's definitely not using the 320 GB Hard Disk. I tried the following: sudo mkdir /media/newhd (worked) sudo mount /dev/sda /media/newhd (didn't work. it says I must specify the filesystem type) I then tried: fsck.ext4 -f /dev/sda (didn't work. Said: Superblock invalid, trying to backup blocks. then: Bad magic number in super-block while trying to open /dev/sda. The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock) Does anyone have any ideas? The whole problem started when my Windows Vista said "Can't find operating system". Any ideas on how I can get on to my hard drive at /dev/sda?

  Read the article

• Ubuntu + LigHTTPd: Server requests taking ages

  - by ctrl_freak

  I've had an issue since upgrading my distro a couple of weeks ago from hardy; receiving data after making a request has increasing intervals of nothing, as you can see from the picture below. http://i49.tinypic.com/2w5lvr9.png I have since reinstalled fresh from an Ubuntu 10.04 Server (i386) disk, but am still having the same issues. I'm running on a LigHTTPd, MySQL, PHP5 stack. The surprising thing is, that local browsing using lynx is super fast, as expected. Initially, after reinstalling, I copied over the old configuration files from the previous installation, but have since reinstalled LigHTTPd and rebuilt the config file from scratch. The only correlation I could find, was that I attempted installation of ionCube and Zend Optimizer for a script I was testing, however I would think that it could no longer impact seeing I had reinstalled the OS. I have also removed Suhosin just in case, however it had no impact. I'm thinking it possibly has something to do with networking, but I wouldn't know where to start. The server is manually assigned an IP by it's MAC address on the router. The fact that the time seems to be exponential (to a point) worries me. I've tried strace'ing the LigHTTPd and MySQL processes, however I couldn't see anything obvious, not that I'd really know what I'm looking for. RAM and CPU usage don't seem to be out of the ordinary, but I can't say its perfect.. I'm hoping someone has experienced the same, or can point me in a direction, as searching has proved fruitless as I don't know anything specific. Config files can be posted, if requested.

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• UML Linux - vmlinux.o Error 1 - final close failed: Input/output error

  - by Zach

  I'm trying to install UML linux. Kernel is 2.6.28. I link to Linux files so that I have a read-only copy that I can revert back to. I then run the commands: make defconfig ARCH=um # works make ARCH=um # errors out at the very end: final close failed: Input/output error make: *** [vmlinux.o] Error 1 Because of this error, my binary vmlinux never gets created so I can't run my own UML Linux. Any ideas?

  Read the article

• error with "pmem.c" compiling linux source code for android

  - by Preetam

  I am compiling linux source code for android emulator. When i execute make command(for building and cross-compiling the linux source) i get the following error "pmem.c" file. root@ubuntu:~/common# make CHK include/linux/version.h CHK include/linux/utsrelease.h SYMLINK include/asm - include/asm-x86 CALL scripts/checksyscalls.sh CHK include/linux/compile.h CC drivers/misc/pmem.o drivers/misc/pmem.c:441: error: conflicting types for ‘phys_mem_access_prot’ /home/preetam/common/arch/x86/include/asm/pgtable.h:383: note: previous declaration of ‘phys_mem_access_prot’ was here drivers/misc/pmem.c: In function ‘flush_pmem_file’: drivers/misc/pmem.c:805: error: implicit declaration of function ‘dmac_flush_range’ drivers/misc/pmem.c: In function ‘pmem_setup’: drivers/misc/pmem.c:1265: error: implicit declaration of function ‘ioremap_cached’ drivers/misc/pmem.c:1266: warning: assignment makes pointer from integer without a cast make[2]: * [drivers/misc/pmem.o] Error 1 make[1]: [drivers/misc] Error 2 make: ** [drivers] Error 2 root@ubuntu:~/common# how to resolve this error. It seems that there may some problems in the "pmem.c" file and i'll have to choose different git repository. but that would be a very complex thing, as now i have already done most of the things till here. I might have to see correct version of this file. please someone tell what should i do? how to solve this errors. please help..thankyou!

  Read the article

• Linux System Programming

  - by AJ

  I wanted to get into systems programming for linux and wanted to know how to approach that and where to begin. I come from a web development background (Python, PHP) but I also know some C and C++. Essentially, I would like to know: Which language(s) to learn and pursue (I think mainly C and C++)? How/Where to learn those languages specific to Systems Programming? Books, websites, blogs, tutorials etc. Any other good places where I can start this from basics? Any good libraries to begin with? What environment setup (or approx.) do I need? Assuming linux has to be there but I have a linux box which I rarely log into using GUI (always use SSH). Is GUI a lot more helpful or VI editor is enough? (Please let me know if this part of the question should go to serverfault.com) PS: Just to clarify, by systems programming I mean things like writing device drivers, System tools, write native applications which are not present on Linux platform but are on others, play with linux kernel etc.

  Read the article

• Running virtual machines: Linux vs Windows 7

  - by vikp

  Hi, I have tried running windows xp development virtual machine under windows 7 and the performance was dreadful. I'm considering installing Linux and running the virtual machine from the Linux, but I'm not sure whether I can expect any performance gains? It's a 2.4ghz core 2 duo machine with 4gb ram and 5400 rpm hdd. Can somebody please recommend very cut down version of linux that can run VMWare player and isn't resource hungry? Thank you

  Read the article

• Linux memory fragmentation

  - by Raghu

  Hi all, Is there a way to detect memory fragmentation on linux ? This is because on some long running servers I have noticed performance degradation and only after I restart process I see better performance. I noticed it more when using linux huge page support -- are huge pages in linux more prone to fragmentation ? I have looked at /proc/buddyinfo in particular. I want to know whether there are any better ways to look at it.

  Read the article

• Learning resources for Linux filesystem, command line, and structure

  - by webworm

  Can anyone suggest some good materials for learning more about the Linux filesystem and command line? I have found myself frequently confused as to what programs go where on the Linux filesystem. I would like to learn how the various directories (var, etc, usr ...) are used and how to use the commandline more effectively. I come from the Windows development world (.NET developer) so I am very familiar with Windows system administration. However, when doing more and more work with PHP I found myself lost in the internals of Linux (specifically Ubuntu). For example I was having problems installing PEAR properly on my Ubuntu system and not understanding why it was installed where it was. All of my interactions with Linux machines is done via SSH so I would like to focus on the command line and the filesystem. Thanks for any suggestions.

  Read the article

• Java application installer for linux

  - by rusiruboteju

  How can I create a linux installer for java desktop application? for an instance if we want to install netbeans on ubuntu there is a download which is named as "netbeans-6.8-ml-java-linux.sh" so how can i create "mydesktopapp-linux.sh" i have the properly working .jar file i want to distribute my java desktop app. Can anyone help me?

  Read the article

• Ubuntu Linux main utilities

  - by Harry

  I've never used Ubuntu Linux before, but I am researching about the main system tools that are included, e.g. Windows has Disk Cleanup, Disk Defrag... but what does Ubuntu Linux have. I need to know what the main five utilities that are included on Ubuntu Linux and what do they do.

  Read the article

• Bouncy Castle provider don't work in Linux Ubuntu

  - by Tom Brito

  I've successful installed Bouncy Castle in a Windows environment, but the same steps isn't working for Linux Ubuntu (V9.04). Does anyone know any difference from installing Bouncy Castle in Windows and Linux? Or any bug with Bouncy Castle in Linux Ubuntu 9.04?

  Read the article

• Proftpd on Ubuntu - Create directory permission denied (550 ) after upgrade to 9.10

  - by Ian

  Hi all, I am having problems with ProFTPD since I upgraded to Ubuntu 9.10 from 9.04. When I login as my ftp user (userftp) in the terminal I can create dirs fine in their home dir. But when I use ftp as this user permission is denied (550 asl: permission denied) when I try and do the same operation (creating a dir). Uploading files is fine though. I am using the same config for proftpd as I was before, I can't understand what's wrong. Any help appreciated! Config follows: Include /etc/proftpd/modules.conf UseIPv6 on IdentLookups off ServerName "whatever" ServerType inetd DeferWelcome off MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ DefaultRoot ~ Port 21 <IfModule mod_dynmasq.c> </IfModule> MaxInstances 8 User proftpd Group nogroup Umask 022 022 AllowOverwrite on TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # My additions # MaxLoginAttempts 5 # # My user config # #VALID LOGINS <Limit LOGIN> AllowUser userftp DenyALL </Limit> <Directory /home/userftp> Umask 022 022 AllowOverwrite off <Limit MKD STOR DELE XMKD RNRF RNTO RMD XRMD> DenyAll </Limit> </Directory> <Directory /home/userftp/upload/> Umask 022 022 AllowOverwrite on <Limit READ> DenyAll </Limit> <Limit STOR CWD MKD RMD DELE> AllowAll </Limit> </Directory>

  Read the article

• Can't install Perl DBD module on Ubuntu (for Bugzilla)

  - by Mara

  Trying to install bugzilla-4.2.2 on Ubuntu 12.04. When I run checksetup.pl I get the following error: YOU MUST RUN ONE OF THE FOLLOWING COMMANDS (depending on which database you use): PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql SQLite: /usr/bin/perl install-module.pl DBD::SQLite Oracle: /usr/bin/perl install-module.pl DBD::Oracle To attempt an automatic install of every required and optional module with one command, do: /usr/bin/perl install-module.pl --all I have installed MySQL via XAMPP so I run: /urs/bin/perl install-module.pl DBD::mysql And get the following error: perl Makefile.PL --testuser=username Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Failed to determine directory of mysql.h. Use perl Makefile.PL --cflags=-I<dir> to set this directory. For details see the INSTALL.html file, section "C Compiler flags" or type perl Makefile.PL --help Warning: No success on command[/usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl] CAPTTOFU/DBD-mysql-4.021.tar.gz /usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl -- NOT OK Skipping test because of notest pragma Running make install Make had some problems, won't install Could not read metadata file. Falling back to other methods to determine prerequisites So then I tried checksetup.pl's suggestion and ran: /usr/bin/perl install-module.pl --all And it seems to have installed DBD::SQLite without any problems, but again I see a warning that says it's skipping tests because of notest pragma. When I re-run checksetup.pl It shows 3 of the 4 original DB drivers in the "not found" list: PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql Oracle: /usr/bin/perl install-module.pl DBD::Oracle So running it with --all seems to have installed the SQLite driver without any problems, but for some reason I can't seem to install the MySQL driver. Again I need MySQL because thats what XAMPP uses and because I prefer MySQL regardless. I have a feeling it has something to do with this notest pragma error. Any ideas? Thanks in advance!

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by E3 Group

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Help to setup networking in Virtualbox Ubuntu Guest from Windows vista Host

  - by Ramesh Vel

  Hi, I am trying to access the MYSQL installed inside the Ubuntu Guest (In VirtualBox) from my Windows vista Host. It always says not able to find the given IP in the network. I have tried ping the ubuntu virtual machine, but it was not working. So i believe root cause for this is, some bridging between Host & Guest is not enabled. Since i am very new to Ubuntu, am not able to troubleshoot this. Can someone help me out? Cheers

  Read the article

• Ubuntu for Android on the ASUS Transformer Prime

  - by sola

  I would like to use Ubuntu on my Transformer Prime in parallel with Android (not as a dual booting solution, I want to be able to switch between them instantaniously). I am aware of the traditional chrooting/VNC solution but I heard that it performs very poorly so I would like to use Ubuntu For Android (UFA) which has been announced recently by Canonical. That looks like a polished, highly integrated solution for Android devices. The Prime would be the ideal device for Ubuntu For Android since it has a powerful processor (Tegra3) capable of running a lot of processes in parallel on its 4 cores. Does anyone know if Canonical or anybody else is working on supporting UFA on the ASUS Transformer Prime? As far as I understand, the X11 driver is available for Tegra3 so, the biggest hurdle may be easily overcome.

  Read the article

• Ubuntu Laptop Screen does not turn on after sleep

  - by Gage

  I recently put Ubuntu 10.10 on my laptop and after fixing the wireless problem I am only stuck on my screen turning back on after sleep. I have had this problem since Ubuntu 7. I tried using Ubuntu way back then and had a whole bunch of issues with the sleep and the wireless(Broadcom 4311). Anyways, I have an ATI Radeon express 200M graphics card (old laptop). When I go to Hardware drivers it doesn't give me any options to use the closed source drivers. Any suggestions on what I should do? I am going to try what is suggested in this thread but I am at work right now. Laptop does not wake up after sleep Thanks in advance for any help.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by LOGIC9

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Can't remove Ubuntu Desktop from dropdown menu on logon screen

  - by Bryan

  Hello All, I'm running Ubuntu on an Eee PC with the Netbook interface. I installed Ubuntu Desktop via Aptitude to see how well it works on the Eee PC, and after a while I wanted to rid myself of it. So, I purged it using Aptitude, but it still shows up as an option in the dropdown menu on the login screen. Is there any way I can remove the Ubuntu Desktop option from the dropdown menu? It's not a big deal I guess... I'm just curious now how to do it. :)

  Read the article

• How to load Xmir on Ubuntu Touch Saucy

  - by jaro123

  How to load Xmir on Ubuntu 13.10 Nexus 7 tablet, unity8 + lightdm + mir, unity-system-compositor + Xorg installed. Still getting message above after system reboot in the /var/log/Xorg.0.log : [ 81.542] (II) "glx" will be loaded by default. [ 81.542] (WW) "xmir" is not to be loaded by default. Skipping. [ 81.542] (II) LoadModule: "dri2" Thanks Note: No, this question is not duplicate with How to load Xmir on Ubuntu 13.10 because. My note that this do not work on Ubuntu Touch Saucy + Nexus7 tablet was removed by fossfreedom. I do feel it duplicate also, but this moderator issue. There is no chance to response on equal topic, even when it is not obviously solving the problem. I do consider this confusing and causing incomplete answers.

  Read the article

• sendmail on ubuntu (9.10) machine "stopped" sending mail

  - by Doron

  I'm developing on my ubuntu 9.10 machine for the web (php). I'm using it sendmail for sending mails, and while developing on my local machine, I send local mails (to my user 'doron'). Up until a few days ago, I was able to send mails both from php's mail() function, and from the command line using the mail command. I'm using sendmail with mailutils. Since the last few days, it seems like it stopped working. When I try to send mail from the command line, I get the following in my syslog (and mail.info, and mail.log): Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: from=doron, size=84, class=0, nrcpts=1, msgid=<201003031127.o23BRwlA004693@doron-desktop.>, relay=doron@localhost Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: ruleset=check_rcpt, arg1=<doron@doron-desktop>, relay=localhost [127.0.0.1], reject=553 5.1.8 <doron@doron-desktop>... Domain of sender address doron@doron-desktop does not exist Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: to=<doron@doron-desktop>, ctladdr=doron (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30084, relay=[127.0.0.1] [127.0.0.1], dsn=5.1.8, stat=User unknown Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: from=<doron@doron-desktop>, size=84, class=0, nrcpts=0, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Trying to telnet locally to port 25 results in the following (same output for doron@doron-desktop): doron@doron-desktop:/var/mail$ telnet localhost 25 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 doron-desktop. ESMTP Sendmail 8.14.3/8.14.3/Debian-9ubuntu1; Wed, 3 Mar 2010 13:26:06 +0200; (No UCE/UBE) logging access from: localhost(OK)-localhost [127.0.0.1] helo localhost 250 doron-desktop. Hello localhost [127.0.0.1], pleased to meet you mail from: doron@localhost 250 2.1.0 doron@localhost... Sender ok rcpt to: root@localhost 553 5.1.8 root@localhost... Domain of sender address doron@doron-desktop does not exist However - if I do the same, but use [email protected] in the mail from field, I get: 250 2.1.5 root... Recipient ok My /etc/hosts file: 127.0.0.1 localhost 127.0.1.1 doron-desktop doron-desktop. (If I don't have the "doron-desktop." (with the ending dot), the mail command takes a lot of time (around 30 seconds) until it responds, but the results are the same.)

  Read the article

• How to impove Ubuntu performance on netbook

  - by Alexey Shytikov

  Most recent Ubuntu 12.04 seems to be quite nice and Unity (3D/2D) works fine for me, however not on my old Acer Aspire One any more. There was a times, when I switched from Windows XP to Ubuntu and was happy about system looks, effects and speed... now I attend to think that XP was really great comparing with 12.04. I have found similar questions here but no reasonable answer: how to lower CPU usage for Unity (3D/2D) and memory consumption for Ubuntu 12.04. With new interface I could not find how to disable background services... It's Linux, it's should be the way to optimize without buying new PC... Please share your recipe!

  Read the article

• Performance cost of running Ubuntu from external hard drive

  - by dandan78

  A friend just complained to me about Ubuntu being slow. Although I've noticed a certain lack of snappiness with Linux vs Windows in the past, I really can't say I've had much to grumble about with the recent distributions of Ubuntu. That said, his objections seem much worse than the ones I used to have and I know that his current setup is significantly more powerful than my laptop. And then it turned out he is running Ubuntu off an external HDD hooked up via USB2.0. The HD enclosure is USB3.0 but apparently he can't manage to get it to boot on USB3.0 so he switched to one of the USB2.0 ports or whatever and that works, albeit not very well. Now I would expect USB to add some overhead to communication between the computer and the HDD; SATA is after all designed to get the maximum out of a hard drive, whereas USB is, well, universal. What are your expreriences with booting off external HDDs? Edit: Does anybody know just how much of a slowdown can be expected?

  Read the article

• sendmail on ubuntu (9.10) machine "stopped" sending mail

  - by Doron

  I'm developing on my ubuntu 9.10 machine for the web (php). I'm using it sendmail for sending mails, and while developing on my local machine, I send local mails (to my user 'doron'). Up until a few days ago, I was able to send mails both from php's mail() function, and from the command line using the mail command. I'm using sendmail with mailutils. Since the last few days, it seems like it stopped working. When I try to send mail from the command line, I get the following in my syslog (and mail.info, and mail.log): Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: from=doron, size=84, class=0, nrcpts=1, msgid=<201003031127.o23BRwlA004693@doron-desktop.>, relay=doron@localhost Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: ruleset=check_rcpt, arg1=<doron@doron-desktop>, relay=localhost [127.0.0.1], reject=553 5.1.8 <doron@doron-desktop>... Domain of sender address doron@doron-desktop does not exist Mar 3 13:27:58 doron-desktop sendmail[4693]: o23BRwlA004693: to=<doron@doron-desktop>, ctladdr=doron (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30084, relay=[127.0.0.1] [127.0.0.1], dsn=5.1.8, stat=User unknown Mar 3 13:27:58 doron-desktop sm-mta[4694]: o23BRwtQ004694: from=<doron@doron-desktop>, size=84, class=0, nrcpts=0, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Trying to telnet locally to port 25 results in the following (same output for doron@doron-desktop): doron@doron-desktop:/var/mail$ telnet localhost 25 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 doron-desktop. ESMTP Sendmail 8.14.3/8.14.3/Debian-9ubuntu1; Wed, 3 Mar 2010 13:26:06 +0200; (No UCE/UBE) logging access from: localhost(OK)-localhost [127.0.0.1] helo localhost 250 doron-desktop. Hello localhost [127.0.0.1], pleased to meet you mail from: doron@localhost 250 2.1.0 doron@localhost... Sender ok rcpt to: root@localhost 553 5.1.8 root@localhost... Domain of sender address doron@doron-desktop does not exist However - if I do the same, but use [email protected] in the mail from field, I get: 250 2.1.5 root... Recipient ok My /etc/hosts file: 127.0.0.1 localhost 127.0.1.1 doron-desktop doron-desktop. (If I don't have the "doron-desktop." (with the ending dot), the mail command takes a lot of time (around 30 seconds) until it responds, but the results are the same.)

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >