Search Results

Search found 12200 results on 488 pages for 'lubuntu desktop'.

Page 462/488 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Web Service gets unavailable after several concurrent calls

  - by Roman

  We are testing GoDaddy Virtual Data Center and came to a very strange issue when our web site gets unavailable. GoDaddy Support keeps saying the issue is in our web server settings, but looking at the result of our tests I doubt it. TEST ENVIRONMENT Virtual DataCenter with Windows hosted at GoDaddy.com. All servers have Windows Server 2008 R2 Datacenter, IIS 7. Server One with IP address 10.1.0.4 Server Two with IP address 10.1.0.3 Both servers are in private network not visible from outside. Port Forward with IP address 50.62.13.174. Port Forward is assigned to Server One TEST DESCRIPTION JMeter is used as a Client App to simulate 30 concurrent users sending 100 SOAP requests each. Interval between requests is 1 second. Http link used for testing: http://50.62.13.174/v2/webservices.asmx TEST ONE Test is run from a computer in our office. After JMeter starts running test, almost immediately, the link above becomes unavailable in a browser. After test completion, the link is not available in a browser for about 5 more minutes. Remote Desktop is working well, so we can connect to Server One remotely. After about 5 minutes since test completion, the link becomes available in a browser again. TEST TWO Test is run from Server Two (that is part of our virtual data center). Test works very well, no visible delays in processing. The link is available in a browser all the time. TEST THREE Test is run from Server One using localhost. The result is the same as in TEST TWO - no issues. TEST FOUR We repeated TEST ONE from other computers that we have located in different countries, all with the same result as TEST ONE. CONCLUSION As the test works well from Server Two, but does not work from outside our virtual data center, we feel there are issues with the network or its capacity. The whole behaviour looks like out requests from outside get stuck somewhere before reaching our virtual data center. Has anybody had similar issues in the past? Are there chances that something is wrong with our server settings?

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• ffmpeg video4linux2 at specified resolution

  - by wim

  When I'm trying to record a clip from my webcam, using: ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi I get annoying problem with very low resolution video, and there is a message from ffmpeg saying: [video4linux2,v4l2 @ 0x2bff3e0] The V4L2 driver changed the video from 800x600 to 176x144 I have tried not specifying -s, or trying other sizes like 800x600, and always it forces me back to 176x144. Why is this and how can I prevent it? My webcam is one of those Logitech 9000 Pro, I know it supports better resolutions than this and I can see with v4l2-ctl --list-formats-ext that it goes up to at least 800x600. edit: complete console output follows wim@wim-desktop:~$ ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi ffmpeg version git-2012-11-20-70c0f13 Copyright (c) 2000-2012 the FFmpeg developers built on Nov 21 2012 00:09:36 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 8.100 / 52. 8.100 libavcodec 54. 73.100 / 54. 73.100 libavformat 54. 37.100 / 54. 37.100 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 23.101 / 3. 23.101 libswscale 2. 1.102 / 2. 1.102 libswresample 0. 17.100 / 0. 17.100 libpostproc 52. 2.100 / 52. 2.100 [video4linux2,v4l2 @ 0x37a33e0] The V4L2 driver changed the video from 640x480 to 176x144 [video4linux2,v4l2 @ 0x37a33e0] Estimating duration from bitrate, this may be inaccurate Input #0, video4linux2,v4l2, from '/dev/video0': Duration: N/A, start: 37066.740548, bitrate: 6082 kb/s Stream #0:0: Video: rawvideo (YUY2 / 0x32595559), yuyv422, 176x144, 6082 kb/s, 15 tbr, 1000k tbn, 15 tbc File '/tmp/spam.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to '/tmp/spam.avi': Metadata: ISFT : Lavf54.37.100 Stream #0:0: Video: mpeg4 (FMP4 / 0x34504D46), yuv420p, 176x144, q=2-31, 200 kb/s, 15 tbn, 15 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> mpeg4) Press [q] to stop, [?] for help frame= 95 fps= 22 q=2.0 Lsize= 88kB time=00:00:13.86 bitrate= 51.8kbits/s video:77kB audio:0kB subtitle:0 global headers:0kB muxing overhead 13.553706%

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• AWS EC2 - How to specify an IAM role for an instance being launched via awscli

  - by Skaperen

  I am using the "aws ec2 run-instances" command (from the awscli package) to launch an instance in AWS EC2. I want to set an IAM role on the instance I am launching. The IAM role is configured and I can use it successfully when launching an instance from the AWS web UI. But when I try to do this using that command, and the "--iam-instance-profile" option, it failed. Doing "aws ec2 run-instances help" shows Arn= and Name= subfields for the value. When I try to look up the Arn using "aws iam list-instance-profiles" it gives this error message: A client error (AccessDenied) occurred: User: arn:aws:sts::xxxxxxxxxxxx:assumed-role/shell/i-15c2766d is not authorized to perform: iam:ListInstanceProfiles on resource: arn:aws:iam::xxxxxxxxxxxx:instance-profile/ (where xxxxxxxxxxxx is my AWS 12-digit account number) I looked up the Arn string via the web UI and used that via "--iam-instance-profile Arn=arn:aws:iam::xxxxxxxxxxxx:instance-profile/shell" on the run-instances command, and that failed with: A client error (UnauthorizedOperation) occurred: You are not authorized to perform this operation. If I leave off the "--iam-instance-profile" option entirely, the instance will launch but it will not have the IAM role setting I need. So the permission seems to have something to do with using "--iam-instance-profile" or accessing IAM data. I repeated several times in case of AWS glitches (they happen sometimes) and no success. I suspected that perhaps there is a restriction that an instance with an IAM role is not allowed to launch an instance with a more powerful IAM role. But in this case, the instance I am doing the command in has the same IAM role that I am trying to use. named "shell" (though I also tried using another one, no luck). Is setting an IAM role not even permitted from an instance (via its IAM role credentials)? Is there some higher IAM role permission needed to use IAM roles, than is needed for just launching a plain instance? Is "--iam-instance-profile" the appropriate way to specify an IAM role? Do I need to use a subset of the Arn string, or format it in some other way? Is it possible to set up an IAM role that can do any IAM role accesses (maybe a "Super Root IAM" ... making up this name)? FYI, everything involves Linux running on the instances. Also, I am running all this from an instance because I could not get these tools installed on my desktop. That and I do not want to put my IAM user credentials on any AWS storage as advised by AWS here. after answered: I did not mention the launching instance permission of "PowerUserAccess" (vs. "AdministratorAccess") because I did not realize additional access was needed at the time the question was asked. I assumed that the IAM role was "information" attached to the launch. But it really is more than that. It is a granting of permission.

  Read the article

• What is it that kills laptop batteries?

  - by Mala

  There are many superstitions on what you must never do lest your battery become worthless - and by worthless I mean hold about 16 - 24 seconds of charge. This has happened to every laptop I have ever owned, and I just got a new one, so please help me sort out fact from fiction. Here are some of the things I've heard: Do not keep your laptop fully charged. You must run it completely down every so often. Do not use your laptop plugged in to the wall. Only plug it in when it needs charge. If you will not be using your laptop for a long period of time, don't leave it at full charge. Do not leave your laptop running 24/7. The first two I know to be complete fiction: this was true of old batteries such as you might have had in an iPod in 2003, but modern batteries function better when kept at or near full charge. Devices even have circuitry to prevent you from completely depleting your battery, as this is dangerous. The third point sounds probable, and I'd be interested to know if it was true. However, it doesn't really apply to me because I'm not really the type to leave my laptop alone for a day, much less a "long period of time" The fourth seems most likely of the above, but only because of causality: I have always done this, and my batteries have always crapped out on me. I've generally treated a laptop like a desktop with a battery backup, and that I can move from one room to another if necessary. The fact that my batteries tend to last less than 30 seconds has further entrenched this behavior. Should I be trying to break this habit? Are there any other things that ruin laptop batteries? I love that I can actually use my new laptop unplugged :) I'd like to keep it that way. Update: Additional question: If the computer will be used for an extended period of time plugged in, does it make sense to remove the battery first? Update 2: I know people with laptops older than mine, who actively use their laptops as much as I do, and their batteries still hold about an hours' charge while mine holds less than 30 seconds, hence my belief that something I'm doing kills them.

  Read the article

• Hell: NTFS "Restore previous versions"...

  - by ttsiodras

  The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

  Read the article

• Windows startup Powershell script not closing after Start-Process

  - by Matthew Phipps

  I've got a Powershell V2.0 startup script for my work computer (XP Professional 64-bit), as follows: start "C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE" -ArgumentList "/recycle" sleep -S 2 start "C:\Program Files (x86)\Mozilla Firefox\firefox.exe" -ArgumentList "https://mail.google.com" sleep -S 2 start "C:\Program Files (x86)\Mozilla Firefox\firefox.exe" -ArgumentList "-new-window https://www.google.com/calendar" sleep -S 2 start "C:\Program Files (x86)\Skype\Phone\Skype.exe" The sleeps are to ensure that the windows appear on the taskbar in the correct order. I run this from a shortcut on my Quick Launch with the following Target: C:\WINDOWS\system32\WindowsPowerShell\v1.0\powershell.exe C:\scripts\initialize.ps1 (Yes, this is 2.0: powershell -Version 2.0 works, as does -Version 1.0, but not -Version 3.0) Problem is, the command window stays open until the Firefox windows are closed, which is not what I want. Looking at Process Explorer when I run the script, here's what happens: powershell.exe appears under explorer.exe and the Powershell window appears (with a black background, oddly. But it's not cmd.exe, since when I was debugging the script error messages would appear in red). outlook.exe appears under powershell.exe and the Outlook window appears. firefox.exe appears under powershell.exe and a Firefox window appears. A second firefox.exe appears under powershell.exe and another Firefox window appears. The second Firefox process then exits, as expected, since Firefox only uses one process. skype.exe appears under powershell.exe and the Skype window appears. The powershell.exe process inexplicably sticks around, as does the Powershell window. If I close both Firefox windows, the powershell.exe process exits and the Powershell window closes, and the outlook.exe and skype.exe processes appear under explorer.exe as expected. I suspect this has something to do with Firefox's standard input, output and error: I wouldn't expect Outlook or Skype to ever output anything to the console, but Firefox has command-line options that allow it to do so. I've looked over my about:config's user set values and didn't find anything suspicious. Finally, if I have a firefox.exe instance already running (started from the desktop shortcut) the problem doesn't occur (the powershell.exe process exits as it ought to). So what's going on here? I'm going to try adding -WindowStyle hidden to the shortcut next (gotta close this Firefox to test it), but I want to get to the bottom of this, if only to improve my understanding of how Windows consoles work.

  Read the article

• Bypassing "Found New Hardware Wizard" / Setting Windows to Install Drivers Automatically

  - by Synetech inc.

  Hi, My motherboard finally died after the better part of a decade, so I bought a used system. I put my old hard-drive and sound-card in the new system, and connected my old keyboard and mouse (the rest of the components—CPU, RAM, mobo, video card—are from the new system). I knew beforehand that it would be a challenge to get Windows to boot and install drivers for the new hardware (particularly since the foundational components are new), but I am completely unable to even attempt to get through the work of installing drivers for things like the video card because the keyboard and mouse won't work (they do work, in the BIOS screen, in DOS mode, in Windows 7, in XP's boot menu, etc., just not in Windows XP itself). Whenever I try to boot XP (in normal or safe mode), I get a bunch of balloons popping up for all the new hardware detected, and a New Hardware Found Wizard for Processor (obviously it has to install drivers for the lowest-level components on up). Unfortunately I cannot click Next since the keyboard and mouse won't work yet because the motherboard drivers (for the PS/2 or USB ports) are not yet installed. I even tried a serial mouse, but to no avail—again, it does work in DOS, 7, etc., but not XP because it doesn't have the serial port driver installed. I tried mounting the SOFTWARE and SYSTEM hives under Windows 7 in order to manually set the "unsigned drivers warning" to ignore (using both of the driver-signing policy settings that I found references to). That didn't work; I still get the wizard. They are not even fancy, proprietary, third-party, or unsigned drivers. They are drivers that come with Windows—as the drivers for CPU, RAM, IDE controller, etc. tend to be. And the keyboard and mouse drivers are the generic ones at that (but like I said, those are irrelevant since the drivers for the ports that they are connected to are not yet installed). Obviously at some point in time over the past several years, a setting got changed to make Windows always prompt me when it detects new hardware. (It was also configured to show the Shutdown Event Tracker on abnormal shutdowns, so I had to turn that off so that I could even see the desktop.) Oh, and I tried deleting all of the PNF files so that they get regenerated, but that too did not help. Does anyone know how I can reset Windows to at least try to automatically install drivers for new hardware before prompting me if it fails? Conversely, does anyone know how exactly one turns off automatic driver installation (and prompt with the wizard)? Thanks a lot.

  Read the article

• Should use EXT4 or XFS to be able to 'sync'/backup to S3?

  - by Rafa

  It's my first message here, so bear with me... (I have already checked quite a few of the "Related Questions" suggested by the editor) Here's the setup, a brand new dedicated server (8GB RAM, some 140+ GB disk, Raid 1 via HW controller, 15000 RPM) it's a production web server (with MySQL in it, too, not just serving web requests); not a personal desktop computer or similar. Ubuntu Server 64bit 10.04 LTS We have an Amazon EC2+EBS setup with the EBS volume formatted as XFS for easily taking snapshots to S3, via AWS' console. We are now migrating to the dedicated server and I want to be able to backup our data to Amazon's S3. The main reason being the possibility of using the latest snapshot from an EC2 instance in case of hardware failure on the dedicated server. There are two approaches I am thinking of: do a "simple" file-based backup with rsync, dumping the database' and other files, and uploading to amazon via S3 API commands, or to an EC2 instance, or something. do a file-system "freeze" (using XFS) with the usual ebs/ec2 snapshot tool to take part of the file system, take a snapshot, and upload it to Amazon. Here's my question (or series of questions): Can I safely use XFS for the whole system as the main and only format on the dedicated server? If not, is it safe to use EXT4? Or should I use something else? would then be possible to make snapshots of the system to upload to Amazon? Is it possible/feasible/practical to do what I want to do, anyway? any recommendations? When searching around for S3/EBS/XFS, anything relevant to my problem is usually focused on taking snapshots of a XFS system that is already an EBS volume. My intention is to do it in a "real"/metal dedicated server. Update: I just saw this on Wikipedia: XFS does not provide direct support for snapshots, as it expects the snapshot process to be implemented by the volume manager. I had always assumed that I could choose 2 ways of doing snapshots: via LVM or via XFS (without LVM). After reading this, I realize these 2 options are more like it: With XFS: 1) do xfs_freeze; 2) copy the frozen files via, eg, rsync; 3) unfreeze xfs With LVM and XFS: 1) do xfs_freeze; 2) make a binary copy of the frozen fs via lvcreate and related commands; 3) unfreeze xfs; 4) somehow backup the LVM snapshot. Thanks a lot in advance, Let me know if I need to clarify something.

  Read the article

• Default Critique branch office setup: VPNTunnel->HQ, subnets for VOIP/PC, + several Q's

  - by CHickenTaragon

  We're setting up a new branch office. * ~10 users. * Each user has a VOIP phone provided by a hosted solution. * Users need access to resources on HQ (located in another state), so setting up VPN tunnel * HQ only supports certain Cisco/Juniper devices. VOIP provider only supports SonicWall, so current plan is to have two routers w/ separate subnets for VOIP vs. PC traffic. * PC's will plug into pass-thru Ethernet jacks on the VOIP phones, but the phones vs. PC's will point to different subnets. * Cable Modem is 50Mbps / 5Mbps DOCSIS 3.0 business line w/ 5 static IP's. * Each of the 2 subnets will map to one of the 5 public IP's. * May or may not also need to support a VPN tunnel with a second branch office because of a file server they have there that some in the new office use. I'm pushing to have them move the files to a server on the HQ's network so we don't have to worry about setting up an additional tunnel. Questions: Do you foresee any issues with the below set-up? Router recommendations by HQ IT staff: Cisco Router 2811, or Juniper SSG5 or SSG20. Any recommendations about these routers? We need Wi-Fi too – looks like the above routers have models that support this, any reason not to use this? Users need to be able to work from home. If so, how is authentication handled? Right now we use AD credentials for the HQ's domain, but we currently don't plan to have an AD system in the new location since it's only 10 users. We can't tie the authentication system from the new location's router to the AD system of the HQ. All the PC's that will be in the new location are currently in the existing office that is closing down, and are already joined to the domain of the HQ. Please confirm: this + the VPN tunnel will be sufficient for them to connect to authenticated resources on the HQ's network from the new location, correct? Mainly SQL servers and file servers, and a few remote desktop sessions. I'm sure I'll have some more questions, but can't think of them right now.

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• PSU failing or Mainboard failing?

  - by Andrei Rinea

  I am having some troubles lately powering on my desktop workstation. While starting up the PC after being off for hours (usually at least 8 hours) it randomly fails to do so. What happens is that : I press the power button; nothing happens I can hear a moderate buzzing noise at the back of the PC (near the PSU); but I can't say for sure that it's not from the mainboard. If I insist pressing the power button a few times in 1-2 minutes it'll start Another route would be that instead of (3) I will plug off the power cable from the PSU and wait for 30 seconds. Then I will press the power on and keep it for 30-60 seconds (I had some success at notebooks with a similar approach). Then I will plug back the cable in the PSU, press only once the power button and it will start normally. Also while running normally I keep hearing some low buzzing which seems to be fan-RPM-related (i.e. when processing images or doing CPU intensive work). What should I look into? UPDATE It's getting worse. It took more than 10 retries today and almost 20 minutes to start the computer. I tried the paperclip trick and the PSU behaves perfectly. I managed to start the computer like so : I pressed the on-button a few times and then left the PC in a pre-startup state (the fans were working the buzzing noise was strong and I went to eat. I thought I won't lit the house on fire so fast and without smelling. Back, after 10-15 min the computer booted up! Discussed with a fellow at Intel and he told me the capacitors on the mainboard are probably a bit shot. If they are shot, he said, it should start up warm perfectly. So I did restart it, warm, a few times (5 sec cooldown and then 40 sec cooldown and it started up perfectly). I can either replace the capacitors on the mainboard (doesn't sound worth it or replace the mainboard (this one sucks too :)) ) FINAL INFO : It was the PSU after all. Although it was powering the IDEs and SATAs the Mainboard power module was failing. I bought another mainboard just to find out that this wasn't the cause. Now I'll have to return it somehow. The spare PSU is now in the computer and doing well.. Although larger (500W), it's like a plane taking off.. I need a better one.

  Read the article

• SSL support with Apache and Proxytunnel

  - by whuppy

  I'm inside a strict corporate environment. https traffic goes out via an internal proxy (for this example it's 10.10.04.33:8443) that's smart enough to block ssh'ing directly to ssh.glakspod.org:443. I can get out via proxytunnel. I set up an apache2 VirtualHost at ssh.glakspod.org:443 thus: ServerAdmin [email protected] ServerName ssh.glakspod.org <!-- Proxy Section --> <!-- Used in conjunction with ProxyTunnel --> <!-- proxytunnel -q -p 10.10.04.33:8443 -r ssh.glakspod.org:443 -d %host:%port --> ProxyRequests on ProxyVia on AllowCONNECT 22 <Proxy *> Order deny,allow Deny from all Allow from 74.101 </Proxy> So far so good: I hit the Apache proxy with a CONNECT and then PuTTY and my ssh server shake hands and I'm off to the races. There are, however, two problems with this setup: The internal proxy server can sniff my CONNECT request and also see that an SSH handshake is taking place. I want the entire connection between my desktop and ssh.glakspod.org:443 to look like HTTPS traffic no matter how closely the internal proxy inspects it. I can't get the VirtualHost to be a regular https site while proxying. I'd like the proxy to coexist with something like this: SSLEngine on SSLProxyEngine on SSLCertificateFile /path/to/ca/samapache.crt SSLCertificateKeyFile /path/to/ca/samapache.key SSLCACertificateFile /path/to/ca/ca.crt DocumentRoot /mnt/wallabee/www/html <Directory /mnt/wallabee/www/html/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> <!-- Need a valid client cert to get into the sanctum --> <Directory /mnt/wallabee/www/html/sanctum> SSLVerifyClient require SSLOptions +FakeBasicAuth +ExportCertData SSLVerifyDepth 1 </Directory> So my question is: How to I enable SSL support on the ssh.glakspod.org:443 VirtualHost that will work with ProxyTunnel? I've tried various combinations of proxytunnel's -e, -E, and -X flags without any luck. The only lead I've found is Apache Bug No. 29744, but I haven't been able to find a patch that will install cleanly on Ubuntu Jaunty's Apache version 2.2.11-2ubuntu2.6. Thanks in advance.

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

• What are incentives (if any) to use WinRT instead of .Net?

  - by Ark-kun

  Let's compare WinRT with .Net .Net .Net is the 13+ years evolution of COM. Three main parts of .Net are execution environment, standard libraries and supported languages. CLR is the native-code execution environment based on COM .Net Framework has a big set of standard libraries (implemented using managed and native code) that can be used from all .Net languages. There are .Net classes that allow using OS APIs. WPF or Silverlight provide a XAML-based UI framework .Net can be used with C++, C#, Javascript, Python, Ruby, VB, LISP, Scheme and many other languages. C++/.Net is a variation of the C++ language that allows interaction with .Net objects. .Net supports inheritance, generics, operator and method overloading and many other features. .Net allows creating apps that run on Windows (XP, 7, 8 Pro (Desktop and Metro), RT, CE, etc), Mac OS, Linux (+ other *nix); iOS, Android, Windows Phone (7, 8); Internet Explorer, Chrome, Firefox; XBox 360, Playstation Suite; raw microprocessors. There is support for creating games (2D/3D) using any managed language or C++. Created by Developer Division WinRT WinRT is based on COM. Three main parts of WinRT are execution environment, standard libraries and supported languages. WinRT has a native-code execution environment based on COM WinRT has a set of standard libraries that more or less can be used from WinRT languages. There are WinRT classes that allow using OS APIs. Unnamed Silverlight clone provides a XAML-based UI framework WinRT can be used with C++, C#, Javascript, VB. C++/CX is a variation of the C++ language that allows interaction with WinRT objects. Custom WinRT components don't support inheritance (classes must be sealed), generics, operator overloading and many other features. WinRT allows creating apps that run on Windows 8 Pro and RT (Metro only); Windows Phone 8 (limited). There is support for creating games (2D/3D) using C++ only. Ordered by Windows Team I think that all the aspects except the last ones are very important for developers. On the other hand it seems that the most important aspect for Microsoft is the last one. So, given the above comparison of conceptually identical technologies, what are incentives (if any) to use WinRT instead of .Net?

  Read the article

• Apache won't follow Symlink

  - by Marvin Dickhaus

  I have a LAMP server (Ubuntu 12.10) setup on my development machine. It is a T60 modified with an SSD. The server base is in /var/www. Apache has the following config: DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews SymLinksIfOwnerMatch AllowOverride all Order allow,deny allow from all </Directory> I'm currently developing a SilverStripe CMS featured site. The folder for the server is /var/www/sfk/. The framework and all cms relavant features are in their respective folders. The only folder that need to be modified would be the /var/www/sfk/mysite folder. Because of that I want to keep the mysite folder under my home directory and symlink it into the server folder. So here is what I've done: ln -s ~/sfk/mysite/ /var/www/sfk/ sudo chgrp www-data /var/www/sfk/mysite -R ls tells me the following: /var/www/sfk (exerpt) drwxr-xr-x 3 marvin www-data 4096 Nov 16 16:53 assets drwxr-xr-x 12 marvin www-data 4096 Nov 16 16:53 cms drwxr-xr-x 29 marvin www-data 4096 Nov 16 16:53 framework -rw-r--r-- 1 marvin www-data 2410 Nov 16 16:53 index.php lrwxrwxrwx 1 marvin www-data 24 Nov 20 17:45 mysite -> /home/marvin/sfk/mysite/ -rw-rw-r-- 1 marvin www-data 514 Nov 16 16:55 _ss_environment.php drwxr-xr-x 4 marvin www-data 4096 Nov 16 16:53 themes and ls /var/www/sfk/mysite/ drwxrwxr-x 6 marvin www-data 4096 Nov 16 00:15 code drwxrwxr-x 2 marvin www-data 4096 Nov 16 11:51 _config -rwxrwxr-x 1 marvin www-data 2685 Nov 16 15:39 _config.php drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 css drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 images drwxrwxr-x 2 marvin www-data 4096 Nov 16 00:15 javascript drwxrwxr-x 5 marvin www-data 4096 Nov 16 00:15 templates This is literally the same setup I have on my desktop machine. The problem I have is that the mysite/ folder is just not recognized. I'm thankful for every advice I get. I'm frustrated because I'm stuck with this issue for hours.

  Read the article

• Problem with several USB devices on Windows XP. How to diagnose USB device?

  - by Lukasz Baran

  Hello All, Recently I've bought some electronic devices (like e.g. Sony Ebook reader PRS-600 or HP PDA IPaq) which are connected to PC using USB ports. These devices have own batteries and they are recharged using USB. However, I am experiencing a problem with Ebook Reader and the similiar thing happens with my PDA (but in this case it's more rare). Sometimes, I am unable to make it start recharging, when it's connected to USB port. The LCD diode on my Reader lights up and the icon in the system tray appears. They both indicate that the device has been connected. However, the device should start recharching and it should appear on Windows XP as a 'explorable' device (just like pendrive it offers some HDDs). None of these happens:( This problem appears on two PCs - desktop and laptop. Both have Windows XP SP3 installed. And what's interesting and surprising to me is the fact that these devices sometimes work without any problems. I mean, I just plug them in and they work properly. Besides that, there are some computers (I have tested a variety of possible conditions) on which the problem does not appear! I am confused and, on the other hand, determined to find out what is the real cause of such strange behavior. Maybe I'm wrong but I always assumed that I'm using deterministic machines, but the described situation makes me feel like I was dreaming:) And that's why I'm asking you here. Are there any tools that could help me diagnose USB ports? Or maybe anyone knows the solution? I have a lot experience with low level programming (mostly from the times of MS-DOS applications), but I'm not an expert when it comes to WinXP technology. If this was a problem with network connection, I would know what to do - I know how to track network traffic, but with USB ports I feel powerless. I have a feeling that the problem may lie in a way WinXP handles USB devices. Personally, I hate auto-discovery and P'n'P features available in Windows. I know that some of may suggest to move to Linux or other *Nix system. Unfortunately, I have to use WinXP in my professional life, so it's rather impossible. Besides that, I don't consider XP as a total disaster. Any help from you will be appreciated!

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• How to temporary disable a mirror video driver in windows xp registry

  - by happy clicker

  Because its a lot of text, I will ask first my question and then explain what the base problem is. Perhaps someone can give me a solution to the base problem: Is there is a way to temporary disable mirror video drivers (through registry or so), without uninstalling the corresponding software. I tested changing the enumeration in LocalMachine\Hardware\DeviceMap\Video but after reboot always the old configuration is restored. Explanation of the base problem We are working on a wpf-project for a department of a big company. There we have the problem that WPF renders only in software mode, although the hardware they have, must support hardware rendering (Tier 2). After searching for a solution to the problem, we found out that direct 3d does not work properly and we think thats why WPF can only use SW-rendering. In dxdiag.exe the direct3d-acceleration is enabled, but if we start the test-routine it always fails saying that it has not enough memory (it says memory, not video memory!). I have seen there 3 different types of pc’s (they have some hundreds of each type) and every type shows the exactly same behavior. We tried to update all the drivers, also dx (Version 9.0c) and we searched a lot in the web but could not find a solution. All the pcs have Intel Dual-Core processors or better, one type has an Intel gma 9000 graphics card the other two types have actual ATI and NVidia graphic-cards with 256MB onboard memory. Also the system memory is at least 2GB. Windows is XPSP3. The pc’s are of two different manufacturers. Because we see the exactly same behavior on every computer of this three very different computer-types, we don’t think that this is a driver or a direct x problem. What we’ve found in other newsgroups is, that direct x could be disturbed through mirror-video drivers such as NetMeeting, VNC and other remote desktop-installations. In the registry, we see under LocalMachine\Hardware\DeviceMap\Video a lot of such mirror-entries and we find also the definitions in the CurrentControlSet\Control\Video-Section (However this drivers are not shown in the hardware panel of the os). We can have admin-rights to one of these computers to test if disabling these drivers would help, but we must not change the configuration so that some software does not work after the tests. Therefore I cannot uninstall any software because I have not the mediums, licenses or knowhow to reinstall those apps. The support of this company however will only begin to work, if I can tell them what the real problem is. Thats why we search for a way to disable these mirror-drivers (or a hint to solve the dx problem if we are on a false trace)

  Read the article

• Can this USB3 behaviour be anything else than a hardware failure?

  - by Jonas Wielicki

  While my motherboard is half a year old now (ASUS M5A99X EVO), I only recently made use of the USB3 boards (after purchase of USB3 external harddrive). However, I am encountering issues. I am running linux 3.6.7-4.fc16.x86_64. Initially, the harddrive worked fine with USB3 (amazing ˜160MB/s), but I had some problems after putting after putting the harddrive to sleep manually after use (backup) with hdparm -Y. After some time, the device disappears from lsusb and i see the following in dmesg: [ 1924.091107] xhci_hcd 0000:05:00.0: xHCI host not responding to stop endpoint command. [ 1924.091114] xhci_hcd 0000:05:00.0: Assuming host is dying, halting host. [ 1924.091147] xhci_hcd 0000:05:00.0: HC died; cleaning up [ 1924.091233] usb 11-1: USB disconnect, device number 2 [ 1924.091272] sd 6:0:0:0: Device offlined - not ready after error recovery Testing with my (USB3 capable) notebook, I could not immediately reproduce the behaivour. I put the drive to sleep with hdparm -Y and waited for like an hour, but it was still listed in lsusb and responded after a few seconds delay when I tried after the hour of waiting. After an hour, on the desktop, the device would've usually vanished. Googling for this issue, I came across hints that playing around with IOMMU settings and upgrading the BIOS might help. I upgraded the BIOS and tried both with and without IOMMU enabled, got similar results. Most disturbing is, that one of the two USB 3.0 hubs sometimes also disappears from lsusb (or does not show up after boot at all). I've also heard that there are some hardware issues with ASUS USB3 ports. Applying mechanic force to the capble doesn't push the issue to one side or the other. Also, udev seems to reenumerate all devices if I plug the HDD into the USB 3.0 port without success (I can notice from my keyboard layout being changed to the default, which I do not use normally). The drive is externally powered and the external power supply is plugged in (it also stays powered when unplugging from USB, although it will spin down then). So before I try to return the board, I wanted to find out whether this can be anything else than a failure on the motherboard?

  Read the article

• Melting Laptop Power Supply Tip

  - by AlReece45

  Several (6-7) months ago, my laptop power supply cord got a cut in it and stopped working. Having gotten cheap (and short) power supplies in the past, I decided to buy 2 brand new ones from the manufacturer (ASUS). Now, I used my laptop a little less than usual between February and March. During that time I noticed a few times that the power supply, even though plugged in, did not provide power. Often the computer would just off on me. I figured it was just that one power supply being bad. I had left the alternate at my parent's house in another state and asked them to ship it to me. Now, at work the other day I wanted to get a file off the of hard disk. So I booted it up, knowing that it had a low battery, plugged it in. During the first 2 minutes of use, I was told that the battery was low and I should plug it in. I unplugged it, inspected the end (Being plugged in, this was suspicious), and decided I shouldn't plug it back in-- the plastic on the tip was melting from the heat of the metal on the tip. The computer had simply booted up and I had the file-manager open. It had not been on for more than 10 hours. Now I know that computers tend to get pretty hot. However, the melting point of plastic is usually above 200C.. so that's much hotter than the computer should be generating. I went and bought a THIRD power supply. This time a universal one from Best Buy (it was very fast to buy and test). I tried it out on the computer and it's tip is melting as well. My older laptop that uses the universal power supply uses it perfectly (has been about a week and a part of use now). I have tried using the computer without the battery, with the same effect. Obviously, this is not a problem with the power supply. My room mate and I being trained computer techs were contemplating taking the computer apart and desoldering and resoldering on the power tip. (The computer is about 6 months out of its 2-year warranty). We're hoping that will correct the issue as I would prefer to devote my money on a Good Desktop rather than yet ANOTHER $1200+ laptop. Is there any thing I'm missing here that might cause the the tip on the power unit to melt?

  Read the article

• I have been told to accept one error with Memtest86+

  - by DustByte

  Bought a new computer back in August with 4x4 GB RAM. Had problems with the RAM. They sent me four new sticks, which also generated errors. Singled out four sticks (from the eight I now had) that didn't generate any errors. Discovered by coincident a new RAM error last week (this time no BSOD). Contacted the company. According to them there have been issues with a bad stock from last summer so I got two tested 8 GB sticks sent to me. Been running Memtest86+ over the weekend. After 20 hours I got an error (see attached photo). The test has now been running for 37 hours but so far only this one error. I contacted the company where I bought the computer. They wrote back: I wouldn't worry about hat one fail. We have had similar situations here whereby it passes numerous times but then fails once. We think it's an issue with memtest, after all memory is faulty or it isn't so you can't really have it pass a few times, fail the next time around and then pass again! Please trust me on this and continue with the memory we sent you and if your problems continue we'll look at getting it replaced again. I gather from other forum posts that many people do not accept a single error. What could this single error signify, faulty RAM or a glitch in the MEMTEST program (or other)? Update: From the helpful comments below I conclude that an occasional (and rare) "random" error could occur and be acceptable, but repeated errors at the same address would indicate malfunction. Memtest has now run for 45 hours and I still have only one error. For everyone's information, I will keep running the test. In less than two days I am going away for a month. I will most likely leave Memtest running. As I do not have a UPS there is a risk that a power outage will ruin the experiment. The computer is a desktop so I cannot bring it with me (which would curiously have exposed it to more cosmic rays as I will be flying ;)).

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >