Search Results

Search found 12780 results on 512 pages for 'webmaster tools'.

Page 468/512 | < Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• Connecting a 2560x1440 display to a laptop?

  - by tjollans

  Having read Jeff Atwood's blog post on Korean 27" IPS LCDs, I've been wondering to what extent these are useful in a notebook + large display situation. I own a Lenovo Thinkpad Edge E320 with 2nd gen. integrated Intel graphics. According to the spec from Intel, this should support HDMI version 1.4, and, using DisplayPort, resolutions up to 2560x1600. HDMI version 1.4 supports resolutions up to 4096×2160, however, according to c't (German), the HDMI interface used with Intel chips only supports 1920x1200. The same goes for the DVI output - dual-link DVI-D, apparently, is not supported by Intel. It would appear that my laptop cannot digitally drive this kind of resolution. Now what about other laptops? According to the article in c't above, AMD's integrated graphics chips have the same limitation as Intel's. NVIDIA graphics cards, apparently, only offer resolutions up to 1900x1200 over HDMI out of the box, but it's possible, when using Linux at least, to trick the driver into enabling higher resolutions. Is this still true? What's the situation on Windows and OSX? I found no information on whether discrete AMD chips support ultra-high resolutions over HDMI. Owners of laptops with (Mini) DisplayPort / Thunderbolt won't have any issues with displays this large, but if you're planning to go for a display with dual-link DVI-D input only (like the Korean ones), you're going to need an adapter, which will set you back something like €70-€100 (since the protocols are incompatible). The big question mark in this equation is VGA: a lot of laptops have it, and I don't see any reason to think this resolution is not supported by the hardware (an oft-quoted figure appears to be 2048x1536@75Hz, so 2560x1440@60Hz should be possible, right?), but are the drivers likely to cause problems? Perhaps more critically, you'd need a VGA to dual-link DVI-D adapter that converts analog to digital signals. Do these exist? How good are they? How expensive are they? Is there a performance penalty involved? Please correct me if I'm wrong on any points. In summary, what are the requirements on a laptop to drive an external LCD at 2560x1440, in particular one that supports dual-link DVI-D only, and what tools and adapters can be used to lower the bar?

  Read the article

• varnish3, mod_geoip with apache2 using mod_rewrite and mod_rpaf

  - by mursalat

  I am maintaining a website with 3 different versions of the site, with 3 different languages, handles with a single system written in php, which takes in environment variables based on the domain name that is being accessed. These are the three sites: myshop.com : english international version myshop.eu : european version of site myshop.ru : russian version of the site when myshop.com is accessed from russia it is to be redirected to myshop.ru, and any country from europe accesses myshop.com, is redirected to myshop.eu, and international visitors stay at myshop.com, although they can go to the country specific site. All these redirections for the country is done using GeoIP apache2 mod in order to determine the country code, which is used in a RewriteCondition to state a RewriteRule, there are some exceptions of IPs that do not do the rewrite for, basically the IPs of the developer's PCs. The site has been doing just fine, until we decided to setup varnish to give the site a boost, it really did give it a great boost, but the country specific rewrites has become buggy. What started to happen is that a russian visitor can go to myshop.com and won't be redirected, until he clicks a random link (perhaps a link not cached by varnish yet) and the user is redirected to their specific country. For that i setup mod_rpaf, and for exceptions to the rewrite rule (for the developer's ip), i used this RewriteCond %{HTTP:X-FORWARDED-FOR} !^43\.43\.43\.43, and i restarted varnish and apache2, it worked for a while, then it messed up again. And whole day i have been doing changes however i have little no clue as to what's going on, sometimes it works, and sometimes it doesn't, and sometimes it half works, etc... As for geoip, i used a php to check the $_SERVER variable, and here is the general idea of the output [HTTP_X_FORWARDED_FOR] => 43.43.43.44 [HTTP_X_VARNISH] => 1705675599 [SERVER_ADDR] => 127.0.0.1 [SERVER_PORT] => 80 [REMOTE_ADDR] => 43.43.43.44 [GEOIP_ADDR] => 43.43.43.44 [GEOIP_CONTINENT_CODE] => EU [GEOIP_COUNTRY_CODE] => FR [GEOIP_COUNTRY_NAME] => France Now, thanks to the "random" redirects, i hardly have a clue as to what is going on, so can you guys please give me some ideas as to what tools to use to debug this? I have tried to see the redirect logs, but they really dont show much, and varnishlog isn't helping much either - although i must admit i am no professional at varnish. I believe the problem is with varnish trying to cache the url, and thus apache redirects are not being done properly, however visits the site first has a redirect, and based on that other users are served the content, depending on from where the user was when the cache was last updated, is it correct? if so, how can i solve the problem? Also, i have the option of using geoip redirects on varnish3 instead of using apache2 to do the redirects, is that what the best practice is? Any suggestion as to debugging this or to fix this would be helpful! thnx!

  Read the article

• Moving Windows XP from ICH10R RAID 5 to single disk using Linux [migrated]

  - by tudor

  A friend's machine running Windows XP refused to boot recently which is running 3 SATA disks on RAID 5 (which was previously upgraded from RAID 1 not by me). I have determined there to be a disk failure. The disks have been replaced many times in the past few years. I wish to backup the RAID5 partition before I try anything to fix it. The RAID chipset used is ICH10R/DO. So, I plugged in an extra IDE drive and an Ubuntu USB key and looked at the RAID. The partitioning is a mess, but I did find at least one degraded but working RAID array with two partitions, one 79GB and the other 86GB. Then I: 1) Partitioned my IDE disk using fdisk to have a partition of 80GB and bootable, and marked as NTFS. 2) dd the contents of the array to the partition 3) disconnected everything else 4) inserted a Windows XP CD and ran fixboot, fixmbr, and bootcfg. They all run ok and claim that they worked. (e.g. bootcfg detects the Windows partition, fixboot returns saying that it was written correctly.) However, I'm still getting an error like "DISK FAILURE, BOOT DISK NOT FOUND". I have tried running the GRUB rescue disk, which also runs ok, but won't boot into Windows. It just stops with a flashing cursor after chainloader +1, boot. One clue may be that the partitions appear to be wack. One disk has a 79GB RAID partition on a 500GB drive with a offset, the second disk has a 320GB RAID partition across the whole drive. Additionally, the BIOS lists the RAID size as being 149GB. I don't see how this works. How are they even assembling the array when the partitions are so different? I have also tried running the Windows XP automated repair tool, but that didn't work either. I'm presuming this is something simple. Perhaps Windows is attempting to boot into RAID and, upon not finding it, simply crashing? Perhaps the 79GB partitions offset means that it's looking into the disk by that much? Please help!! To clarify: I want to make the single IDE disk bootable with a copy of the array so that I can prove/disprove that it's just that Windows has become corrupted, and use windows tools to correct it before attempting the same thing on the RAID array. That way I have a working backup and can show the process I used to fix it.

  Read the article

• Malware - Technical anlaysis

  - by nullptr

  Note: Please do not mod down or close. Im not a stupid PC user asking to fix my pc problem. I am intrigued and am having a deep technical look at whats going on. I have come across a Windows XP machine that is sending unwanted p2p traffic. I have done a 'netstat -b' command and explorer.exe is sending out the traffic. When I kill this process the traffic stops and obviously Windows Explorer dies. Here is the header of the stream from the Wireshark dump (x.x.x.x) is the machines IP. GNUTELLA CONNECT/0.6 Listen-IP: x.x.x.x:8059 Remote-IP: 76.164.224.103 User-Agent: LimeWire/5.3.6 X-Requeries: false X-Ultrapeer: True X-Degree: 32 X-Query-Routing: 0.1 X-Ultrapeer-Query-Routing: 0.1 X-Max-TTL: 3 X-Dynamic-Querying: 0.1 X-Locale-Pref: en GGEP: 0.5 Bye-Packet: 0.1 GNUTELLA/0.6 200 OK Pong-Caching: 0.1 X-Ultrapeer-Needed: false Accept-Encoding: deflate X-Requeries: false X-Locale-Pref: en X-Guess: 0.1 X-Max-TTL: 3 Vendor-Message: 0.2 X-Ultrapeer-Query-Routing: 0.1 X-Query-Routing: 0.1 Listen-IP: 76.164.224.103:15649 X-Ext-Probes: 0.1 Remote-IP: x.x.x.x GGEP: 0.5 X-Dynamic-Querying: 0.1 X-Degree: 32 User-Agent: LimeWire/4.18.7 X-Ultrapeer: True X-Try-Ultrapeers: 121.54.32.36:3279,173.19.233.80:3714,65.182.97.15:5807,115.147.231.81:9751,72.134.30.181:15810,71.59.97.180:24295,74.76.84.250:25497,96.234.62.221:32344,69.44.246.38:42254,98.199.75.23:51230 GNUTELLA/0.6 200 OK So it seems that the malware has hooked into explorer.exe and hidden its self quite well as a Norton Scan doesn't pick anything up. I have looked in Windows firewall and it shouldn't be letting this traffic through. I have had a look into the messages explorer.exe is sending in Spy++ and the only related ones I can see are socket connections etc... My question is what can I do to look into this deeper? What does malware achieve by sending p2p traffic? I know to fix the problem the easiest way is to reinstall Windows but I want to get to the bottom of it first, just out of interest. Edit: Had a look at Deoendency Walker and Process Explorer. Both great tools. Here is a image of the TCP connections for explorer.exe in Process Explorer http://img210.imageshack.us/img210/3563/61930284.gif

  Read the article

• how to read mac address with sed vs python

  - by getjoefree

  before, i can read mac with awk tools in windows or winpe, but now it don't support winpe 4.0 64-bit. i want to get this result "set mac=A4BADB9D1E8E" with python 2.6, who could help to me. thanks a lot! as follows: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" D:\LOG\WINMAC.BAT getmac.sed: /Realtek/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; } and "ipconfig -all" command log as bellows: ipconfig -all mac.log Ethernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : WKSCN.WISTRON Description . . . . . . . . . . . : Realtek PCIe FE Family Controller Physical Address. . . . . . . . . : 24-B6-FD-1F-41-E7 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes

  Read the article

• Toshiba Satellite L630 broken after bios update

  - by Mustafa Kamal

  I have Toshiba Satellite L630, which has been broken. It had no more OS installed in it. All the disk partition were cleared into one single empty unformatted partition. So I begin to install windows XP on this laptop. Apparently, win XP's driver support for this laptop is very limited. So I have to find almost all important driver (display, sound, etherned, wireless etc) on the net and install it manually one by one. So I start googling, and I got some driver download page from several Toshiba's website (the global version, the europe, asia, etc). Pretty hard to find the exact drivers, but I managed to find pretty good drivers. It's all works quite fine, although still have a few glitches. But everything turned into a big mess when I downloaded the "BIOS Update", which is also listed on Toshiba's official driver directory site. When I installed it, it show a big red warning sign telling me not to do anything while flashing the BIOS . I follow that instruction prudently. The process was finished, and that update BIOS software (it is InsydeH2O BIOS) told me that the BIOS has been succesfully updated and the computer need to restart. So I restart the computer. This is where the problem appear. I can no longer boot to my laptop. The booting process seems to be able to enter windows for a moment (it shows the windows XP loading screen), and then suddenly it just got that hateful blue screen and then instantiy restarts the machine. It goes on a loop. Boot bios - enter XP - blue screen - restart. I can't even try to reinstall my win XP again. Evertime the machine tries to boot to win XP CD, it got the same blue screen as I gets when loading from HDD. Many google search results said that I should open the laptop cover and try to clear CMOS with some kind of jumper or something. Or to unplug/re-plug the CMOS battery. Do I really need to do that? Is there anyway I could do without disassembling my laptop? I read some tricks about booting from USB device but I can't get the exat tools that I need to do that thing... Btw, this is my detailed laptop number photographed from the back of my laptop

  Read the article

• Mounting a drive in Ubuntu 9.10 (Karmic Koala)

  - by morpheous

  I have just installed Ubuntu on a machine that previously had XP installed on it. The machine has 2 HDD (hard disk drives). I opted to install Ubuntu completely over XP. I am new to Linux, and I am still learning how to navigate teh file structure. However, AFAICT), there is only one drive. I want to be able to store programs etc on the first drive, and store data (program output etc) on the second drive. It appears Ubuntu is not aware that I have 2 drives (on XP, these were drives C and D). How can I mount the second drive (ideally, I want to do this automatically on login, so that the drive is available to me whenever I login - withou manual intervention from me) In XP, I could refer to files on a specific drive by prefixing with the drive letter (e.g. c:\foobar.cpp and d:\foobar.dat). I suspect the notation on ubuntu is different. How may I specify specific files on different drives? Last but notbthe least (a bit unrelated to previous questions). This relates to direcory structure again. I am a developer (C++ for desktops and PHP for websites), I want to install the following apps/ libraries. i). Apache 2.2 ii). PHP 5.2.11 iii). MySQL (5.1) iv). SVN v). Netbeans vi). C++ development tools (gcc, gdb, emacs etc) vii). QT toolkit viii). Some miscellaeous scientific software (e.g. www.r-project.org, www.gnu.org/software/octave/) I would be grateful if a someone can recommend a directory layout for these applications. Regarding development, I would also be grateful if someone could point out where to store my project and source files i.e: (i) *.cpp, *.hpp, *.mak files for cpp projects (ii) individual websites On my XP machine the layout for C++ dev was like this: c:\dev\devtools (common libs and headers etc) c:\dev\workarea (root folder for projects) c:\dev\workarea\c++ (c++ projects) c:\dev\workarea\websites (web projects) I would like to create a similar folder structure on the linux machine, but its not clear whether to place these folders under /, /usr, /home or swomewhere else (there seems to be abffling number of choices, so I want to get it "right" first time - i.e having a directory structure that most developer use, so it is easier when communicating with other ubuntu/linux developers)

  Read the article

• Safer RAID5 rebuilds using partially failed disks?

  - by arcticmac

  There have been lots of articles posted recently about how RAID5 is dangerous because of long resilver times, and in particular because of increasing chances of encountering a URE during the resilver. Obviously this is a significant concern. However, it seems that in many cases of interest (as long as you're keeping some kind of eye on your disks), when it comes time to rebuild the array, the disk that I'm replacing is still mostly readable. If you try to explain this predicament to the average layperson, they are typically very confused as to why you have two almost completely functional disks but can't produce one working array. It seems to me that there ought to be some way to take advantage of this to make rebuilds safer, as long as I'm willing to have the RAID5 be read-only for a couple of days while it rebuilds. Conceptually, what I have in mind looks something like this: When a disk fails, immediately take the RAID5 offline or mount it read-only Attach a new disk (either in a spare bay, or externally via eSATA) and begin rebuilding it to replace the failed one. If known, perhaps start with the stripes in which the failure occurred, to minimize the chances of losing those if another disk fails. In the event that a second disk experiences a URE or other failure during the rebuild, try to source that data from the disk that is being replaced. Presumably if this happens, more rebuilding would be necessary. When complete, shut down the server, swap the replacement drive into the original bay if desired, and bring the array back up. Obviously such a process would not be appropriate for applications where uptime is critical or data loss cannot be tolerated, but it seems to me that this could help considerably to improve the reliability of RAID5. I assume that there's not a good way to implement a recovery like this at present, given that I haven't seen any indication of tools that are designed to do this, and that it seems like it would be rather obtuse to work out manually. Are there also technical issues with it that I haven't thought of (I'm still fairly new to RAID stuff)? Any thoughts on how hard something like this would be to implement (e.g. in linux md raid)?

  Read the article

• Impossible to create/format install window 7 on unpartioned HD

  - by fra pet

  Hi guys i am getting nut reinstalling windows 7 on one of those Acer aspire all-in-one... The original OS(windows professional x64) was not starting, after the initial screen the bios was prompted. So step 1: i tried to access the system partition and reinstall everything but could not get at the point step 2: i set the bios to native ide and i tried to insert my original copy of windows professional and do a clean installation, but it does not allow me to format/create other partion form the installation mask step 3: my BAD, i tried to install ubuntu and i clean the whole hard drive, i was getting an error at some point during installation so i decided to get back to windows step 4: Windows 7 again, at the disk screen of the windows installation i entered into the prompt and played around with DISKPART... -i listed the disk and the HD was disk 0. -i selected disk 0. -i CLEAN disk 0 successfully. -i tried to create a CREATE PARTITION PRIMARY but gave an error cache corrupt and disk not up-to-date (after i try to create a partiton in disk 0 it disappear when i try LIST DISK and i have to restart before he can list DISK 0 again, RESCAN did not worked). -tried CLEAN ALL(2 hours) and succeeded. -try again to create primary partition and failed, same errors -try to install my old copy of windows xP pro and it seems to work, it create a partition, format(only quick worked, slow mode was at 0% after 1 hour so i stop), it start installing and around 90% installation said it could not copy a file and he stop -back on windows 7 again, it says that the hard drive has 490+gb unpartitioned but won't create a partition and format. -i tried again DISKPART as i though i messed up with the MBR when i installed ubuntu, so i did all of the instruction below http://www.sevenforums.com/tutorials/20864-mbr-restore-windows-7-master-boot-record.html http://support.microsoft.com/kb/927392 the errors were: on bootsect: the systne partiton was not found, Data error cyclic redundancy check on bootrec /FixMbr: A device attached to the system is not functioning but did not worked, and still can not partiton/format/install on a blank HD i tried some bootable clean disk tool and start infinite loop on the same errors the bios setting are: sata: native ide. if i put AHCL(or something like that does not load the HD and the DVD). quick start/quite start: disabled. Are there any other option or tools i can try before i try change the HD(That is my last option)? Thanks to everyone.

  Read the article

• Convert mkv/h264 video so it can be played on a "mid-range" Sony Ericsson phone. (using Ubuntu).

  - by Johan

  Hi As a little experiment I thinking of converting some video/movies/tv-series into a format that could be playable on my K850, but to be a little bit more generic in this question let's say "mid range Sony Ericsson" phone since they all more or less behave the same and has the same screen resolution (240 x 320). I am looking for command line based tools (for Ubuntu), since I am thinking about writing a "convert and move" script later if it is successful. A lot of the video I have is encoded in mkv/h264, but since that is not supported by the phone I guess that I need to convert it into some mp4/mpeg4 low quality video. After some googling it seems like a good candidate for the job is ffmpeg, but that seems to be a very versatile tool with a lot of magic tricks. Am I on the right track? And if so how do I use ffmpeg to do this? Thanks Johan Update: After plating a little bit with ffmeg I noticed that it only uses 1 of my 4 cores, so the transcoding takes forever. I found a arg called -threads but that did not change much, maybe I got it wrong. I also found that something like this plays in the phone. ffmpeg -i Mythbusters\ S1D1_1.mkv -threads 4 -t 180 -vcodec mpeg4 -r 15 -s 320x240 Mythbusters\ S1D1_1_mini.mp4 It was possible to use 3gp/h263, but the quality was really useless. ffmpeg -i Mythbusters\ S1D1_1.mkv -t 180 -vcodec h263 -acodec libfaac -s cif Mythbusters\ S1D1_1_cif.3gp And it seems like mp4/h264 is also possible and the result is ok, thanks to this question, this one seem to use more than one core as well so it was a little bit faster for me. ffmpeg -i Mythbusters_S1D1_1.mkv -t 180 -acodec libfaac -ab 60k -s 320x240 -vcodec libx264 -b 500k -flags +loop -cmp +chroma -partitions +parti4x4+partp8x8+partb8x8 -flags2 +mixed_refs -me_method umh -subq 6 -trellis 1 -refs 5 -coder 0 -me_range 16 -g 250 -keyint_min 25 -sc_threshold 40 -i_qfactor 0.71 -bt 500k -maxrate 768k -bufsize 2M -qcomp 0.6 -qmin 10 -qmax 51 -qdiff 4 -level 13 -threads 0 -f mp4 Mythbusters_S1D1_1_qvga.mp4 Update: I have tried to use HandBrakeCLI and it is no problem creating a new file that seem to be the same as the one created with ffmpeg with something like this. HandBrakeCLI -i Mythbusters_S1D1_1.mkv --size 100 -E faac -B 60 --maxHeight 240 -r 15 -e x264 -o Mythbusters_S1D1_1_hand.mp4 But that one did not play in the phone... I found this in the official manual: If you transfer video clips using another program than Media Go™, we recommend that you select H.264 Baseline profile video, up to QVGA at 30 fps, VBR 384 kbps (max 768 kps) with AAC+ audio at 128 kbps (max 255 kbps), 48 kHz and stereo audio in mp4 file format. So the idea to use H264 seems to be correct.

  Read the article

• LDAP installed, running, but can't connect remotely [Ubuntu 10.10]

  - by Casey Jordan

  Hi all, I installed LDAP on my ubuntu 10.10 system, using the tutorial found here: https://help.ubuntu.com/10.10/serverguide/C/openldap-server.html Everything seems to be working well, when logged into the server via ssh I can run commands like: > ldapsearch -xLLL -b "dc=easydita,dc=com" uid=john sn givenName cn dn: uid=john,ou=people,dc=easydita,dc=com sn: Doe givenName: John cn: John Doe So I think that's a good sign that things are working well. However I have had zero luck connecting to the server remotely via GUI tools or command line. I have tied JXplorer, and LDAP administration tool. Running commands like this: > ldapsearch -xLLL -W -H ldap://ice.rit.edu -d1 "dc=easydita,dc=com" ldap_url_parse_ext(ldap://ice.rit.edu) ldap_create ldap_url_parse_ext(ldap://ice.rit.edu:389/??base) Enter LDAP Password: ldap_sasl_bind ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP ice.rit.edu:389 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 127.0.0.1:389 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({i) ber: ber_flush2: 34 bytes to sd 3 ldap_result ld 0xb8940170 msgid 1 wait4msg ld 0xb8940170 msgid 1 (infinite timeout) wait4msg continue ld 0xb8940170 msgid 1 all 1 ** ld 0xb8940170 Connections: * host: ice.rit.edu port: 389 (default) refcnt: 2 status: Connected last used: Thu Mar 17 19:42:29 2011 ** ld 0xb8940170 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0xb8940170 request count 1 (abandoned 0) ** ld 0xb8940170 Response Queue: Empty ld 0xb8940170 response count 0 ldap_chkResponseList ld 0xb8940170 msgid 1 all 1 ldap_chkResponseList returns ld 0xb8940170 NULL ldap_int_select read1msg: ld 0xb8940170 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 16 contents: read1msg: ld 0xb8940170 msgid 1 message type bind ber_scanf fmt ({eAA) ber: read1msg: ld 0xb8940170 0 new referrals read1msg: mark request completed, ld 0xb8940170 msgid 1 request done: ld 0xb8940170 msgid 1 res_errno: 49, res_error: <>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_err2string ldap_bind: Invalid credentials (49) I am pretty sure that I set up the admin password correctly, but the tutorial was not very specific about that. (Also could not find instructions on how to reset admin password.) Additional info: I was told that this file might hold important information so I will post it: /etc/ldap/slapd.d/cn=config/olcDatabase={0}config.ldif dn: olcDatabase={0}config objectClass: olcDatabaseConfig olcDatabase: {0}config olcAccess: {0}to * by dn.exact=cn=localroot,cn=config manage by * break olcRootDN: cn=admin,cn=config structuralObjectClass: olcDatabaseConfig entryUUID: eca09490-e524-102f-87c5-17d7a82e8985 creatorsName: cn=config createTimestamp: 20110317205733Z entryCSN: 20110317205733.193089Z#000000#000#000000 modifiersName: cn=config modifyTimestamp: 20110317205733Z Given that it seems I have this almost set up correctly is there any steps I can take to correct this? Thanks, Casey

  Read the article

• Slow wifi from Windows Server 2003 virtualized in XenServer

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks! Update: The issue has been further narrowed down to Windows Server 2003, which Windows Home Server is based on, running in XenServer with the XenServer tools installed.

  Read the article

• dmidecode showing more ram slots than available?

  - by Jestep

  I have some failing RAM in a server and I ran dmidecode to figure out what tyoe of RAM I needed to replace it with. The server has 6 RAM slots, 4 of which are in use. When I run dmidecode this is what I get. dmidecode 2.10 SMBIOS 2.4 present. Handle 0x001F, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 00 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0020, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 01 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0021, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 02 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0022, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 03 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0023, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 10 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0024, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 11 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0025, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 12 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0026, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 13 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Does anyone know why it would show 8 slots, with 4 empty instead of 6 slots with 2 empty? Also, but my records and by other tools, the server has 16Gb and not 8Gb in it currently. grep MemTotal /proc/meminfo MemTotal: 16435808 kB The board is a Tyan S5372-LC, running CentOS 5.4 x64. Also, my error log is showing errors in bank 6. Is there any way to determine which slot bank 6 is in via: dmidecode?

  Read the article

• Active Directory Partition Error

  - by BLAKE

  Right now my active directory is failing a dcdiag test. I can find no info online about this error. When I run dcdiag /test:crossrefvalidation, I get the output: .... Doing primary tests Testing server: Default-First-Site-Name\ad01 Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : mydomain Starting test: CrossRefValidation ......................... mydomain passed test CrossRefValidation Running partition tests on : t Starting test: CrossRefValidation This cross-ref has a non-standard dNSRoot attribute. Cross-ref DN: CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configuration, DC=mydomain,DC=com nCName attribute (Partition name): DC=t Bad dNSRoot attribute: dc01.mydomain.com Check with your network administrator to make sure this dNSRoot attribute is correct, and if not please change the attribute to the value below. dNSRoot should be: t It appears this partition (DC=t) failed to get completely created. This cross-ref (CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configurat ion,DC=mydomain,DC=com) is dead and should be removed from the Active Directory. ......................... t failed test CrossRefValidation .... I used LDP from the windows support tools. I searched for the dnsRoot attribute in "cn=partitions,cn=configuration,dc=mydomain,dc=com", with the filter "(&(objectcategory=crossref)(systemFlags:1.2.840.113556.1.4.803:=5))" I got the result: ***Searching... ldap_search_s(ld, "cn=partitions,CN=Configuration,DC=mydomain,DC=com", 1, "(& (objectcategory=crossref)(systemFlags:1.2.840.113556.1.4.803:=5))", attrList, 0, &msg) Result <0>: (null) Matched DNs: Getting 3 entries: >> Dn: CN=65502be3-fc90-442a-83d8-4b3b91e82439,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: ForestDnsZones.mydomain.com; >> Dn: CN=a3a24d3a-4782-460b-9148-86ac2d86b9ae,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: ad01.mydomain.com; >> Dn: CN=f0ef5771-6225-4984-acd9-c08f582eb4e2,CN=Partitions,CN=Configuration,DC=mydomain,DC=com 1> dnsRoot: DomainDnsZones.mydomain.com; It looks like the bad partition has the name of my first domain controller 'ad01.mydomain.com'. I have googled for a while and have not been able to find any help or documentation about application partitions in Active Directory. Does anyone have any advice on how to cleanup this partition (or what the partition is for)? Does anyone know the repercussions for deleting this partition?

  Read the article

• Workaround with paths in vista

  - by Argiropoulos Stavros

  Not really a programming question but i think quite relative. I have a .exe running in my windows XP PC. This exe needs a file in the same directory to run and has no problem finding it in XP BUT in Vista(I tried this in several machines and works in some of them) fails to run. I'm guessing there is a problem finding the path.The program is written in basic(Yes i know..) I attach the code below. Can you think of any workarounds? Thank you The exe is located in c:\tools Also the program runs in windows console(It starts but then during the execution cannot find a custom file type .TOP made by the creator of the program) ' PROGRAMM TOP11.BAS DEFDBL A-Z CLS LOCATE 1, 1 COLOR 14, 1 FOR i = 1 TO 80 PRINT "±"; NEXT i LOCATE 1, 35: PRINT "?? TOP11 ??" PRINT " €€‚—‚„‘ ’— ‹„’†‘„— ‘’† „”€„€ ’†‘ ‡€€‘‘†‘ ‰€ † „.‚.‘.€. " COLOR 7, 0 PRINT "-------------------------------------------------------------------------------" PRINT INPUT "ƒ?©« «¦¤ ©¬¤«?©«? ¤???... : ", Factor# INPUT "¤¦£ ¨®e¦¬ [.TOP] : ", topfile$ VIEW PRINT 7 TO 25 file1$ = topfile$ + ".TOP" file2$ = topfile$ + ".T_P" file3$ = "Syntel" OPEN file3$ FOR OUTPUT AS #3 PRINT #3, " ‘¬¤«?©«?? ¤??? = " + STR$(Factor#) + " †‹„‹†€: " + DATE$ CLOSE #3 command1$ = "copy" + " " + file1$ + " " + file2$ SHELL command1$ '’¦ ¨®e¦ .TOP ¤« ¨a­«  £ «¤ ?«a?¥ .T_P OPEN file2$ FOR INPUT AS #1 OPEN file1$ FOR OUTPUT AS #2 bb$ = " \\\ \ , ###.#### ###.#### ####.### ##.### " DO LINE INPUT #1, Line$ Line$ = RTRIM$(LTRIM$(Line$)) icode$ = LEFT$(Line$, 1) IF icode$ = "1" THEN Line$ = " " + Line$ PRINT #2, Line$ PRINT Line$ ELSEIF icode$ = "2" THEN Line$ = " " + Line$ PRINT #2, Line$ PRINT Line$ ELSEIF icode$ = "3" THEN Number$ = MID$(Line$, 3, 6) Hangle = VAL(MID$(Line$, 14, 9)) Zangle = VAL(MID$(Line$, 25, 9)) Distance = VAL(MID$(Line$, 36, 9)) Distance = Distance * Factor# Height = VAL(MID$(Line$, 48, 6)) PRINT #2, USING bb$; icode$; Number$; Hangle; Zangle; Distance; Height PRINT USING bb$; icode$; Number$; Hangle; Zangle; Distance; Height ELSE END IF LOOP UNTIL EOF(1) VIEW PRINT CLS LOCATE 1, 1 PRINT " *** ’„‘ ’“ ‚€‹‹€’‘ *** " END

  Read the article

• Sysadmin 101: How can I figure out why my server crashes and monitor performance?

  - by bflora

  I have a Drupal-powered site that seems to have neverending performance problems. It was butt-slow about 5 months ago. I brought in some guys who installed nginx for anonymous visitors, ajaxified a few queries so they wouldn't fire during page load, and helped me find a few bottlenecks in the code. For about a month, the site was significantly faster, though not "fast" by any stretch of the word. Meanwhile, I'm now shelling out $400/month to Slicehost to host a site that gets less than 5,000/uniques a day. Yes, you read that right. Go Drupal. Recently the site started crashing again and is slow again. I can't afford to hire people to come in, study my code from top to bottom, and make changes that may or may not help anymore. And I can't afford to throw more hardware at the problem. So I need to figure out what the problem is myself. Questions: When apache crashes, is it possible to find out what caused it to crash? There has to be a way, right? If so, how can I do this? Is there software I can use that will tell me which process caused my server to die? (e.g. "Apache crashed because someone visited page X." or "Apache crashed because you were importing too many RSS items from feed X.") There's got to be a way to learn this, right? What's a good, noob-friendly way to monitor my current apache performance? My developer friends tell me to "just use Top, dude," but Top shows me a bunch of numbers without any context. I have no clue what qualifies as a bad number or a good number in Top, or which processes are relevant and which aren't. Are there any noob-friendly server monitoring tools out there? Ideally, I could have a page that would give me a color-coded indicator about how apache is performing and then show me a list of processes or pages that are sucking right now. This way, I could know when performance is bad and then what's causing it to be so bad. Why does PHP memory matter? My apparently has a 30MB memory foot print. Will it run faster if I bring that number down? Thanks for any advice. I spent a year or so trying to boost my advertising income so I could hire a contractor to solve my performance woes. I didn't want to have to learn all this sysadmin voodoo. I'm now resigned to the fact that might not have a choice.

  Read the article

• TeamSpeak 3 Disconnects

  - by ArchUser

  I've recently had a few random TS3 mass disconnects and I'm am curious to know where I may find any applications that can help me determine the cause of any types of TS3 server disconnections as we plan on having many more users in the future. I run an almost empty VPS (OpenVZ) server with an ArchLinux template on it. I have 1.5/2GB of RAM, 2GHz of CPU and plenty of hard drive space, to run for the most part, just my TS3 and a low traffic apache web server. This is what I am investigating. 2011-02-04 06:07:05.130343|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.131338|INFO |VirtualServer | 1| client disconnected 'Kevrow'(id:19? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.191849|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.192633|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.193350|INFO |VirtualServer | 1| client disconnected 'Akiris'(id:254) reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194047|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 06:07:05.194726|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-04 07:18:50.327071|INFO |VirtualServer | 1| client disconnected 'Valamoor'(id:224) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339018|INFO |VirtualServer | 1| client disconnected 'Marcus'(id:25? reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.339870|INFO |VirtualServer | 1| client disconnected '[Ash] Setna'(id:75) reason 'reasonmsg=connection lost' 2011-02-04 07:18:51.340515|INFO |VirtualServer | 1| client disconnected 'Guthry'(id:275) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.797353|INFO |VirtualServer | 1| client disconnected 'JohnyRingo'(id:240) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.798517|INFO |VirtualServer | 1| client disconnected 'Maloo roots'(id:196) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.799314|INFO |VirtualServer | 1| client disconnected 'Cpt dravyn'(id:234) reason 'reasonmsg=connection lost' 2011-02-05 04:55:20.839254|INFO |VirtualServer | 1| client disconnected 'scuba'(id:200) reason 'reasonmsg=connection lost' etc... I need to determine if it is my hosting provider or my server, and what tools I can use to determine the issues. My VPS host has told me this... "I checked out the node that your VPS runs on and there is no abnormal system load, or I/O wait from the drive. I also checked the bandwidth history from the server and there have been no spikes or outages."

  Read the article

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• Why won't vyatta allow SMTP through my firewall?

  - by Solignis

  I am setting up a vyatta router on VMware ESXi, But I see to have hit a major snag, I could not get my firewall and NAT to work correctly. I am not sure what was wrong with NAT but it "seems" to be working now. But the firewall is not allowing traffic from my WAN interface (eth0) to my LAN (eth1). I can confirm its the firewall because I disabled all firewall rules and everything worked with just NAT. If put the firewalls (WAN and LAN) back in place nothing can get through to port 25. I am not really sure what the issue could be I am using pretty basic firewall rules, I wrote the rules while looking at the vyatta docs so unless there is something odd with the documentation they "should" be working. Here is my NAT rules so far; vyatta@gateway# show service nat rule 20 { description "Zimbra SNAT #1" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.17 } type source } rule 21 { description "Zimbra SMTP #1" destination { address 74.XXX.XXX.XXX port 25 } inbound-interface eth0 inside-address { address 10.0.0.17 } protocol tcp type destination } rule 100 { description "Default LAN -> WAN" outbound-interface eth0 outside-address { address 74.XXX.XXX.XXX } source { address 10.0.0.0/24 } type source } Then here is my firewall rules, this is where I believe the problem is. vyatta@gateway# show firewall all-ping enable broadcast-ping disable conntrack-expect-table-size 4096 conntrack-hash-size 4096 conntrack-table-size 32768 conntrack-tcp-loose enable ipv6-receive-redirects disable ipv6-src-route disable ip-src-route disable log-martians enable name LAN_in { rule 100 { action accept description "Default LAN -> any" protocol all source { address 10.0.0.0/24 } } } name LAN_out { } name LOCAL { rule 100 { action accept state { established enable } } } name WAN_in { rule 20 { action accept description "Allow SMTP connections to MX01" destination { address 74.XXX.XXX.XXX port 25 } protocol tcp } rule 100 { action accept description "Allow established connections back through" state { established enable } } } name WAN_out { } receive-redirects disable send-redirects enable source-validation disable syn-cookies enable SIDENOTE To test for open ports I have using this website, http://www.yougetsignal.com/tools/open-ports/, it showed port 25 as open without the firewall rules and closed with the firewall rules. UPDATE Just to see if the firewall was working properly I made a rule to block SSH from the WAN interface. When I checked for port 22 on my primary WAN address it said it was still open even though I outright blocked the port. Here is the rule I used; rule 21 { action reject destination { address 74.219.80.163 port 22 } protocol tcp } So now I am convinced either I am doing something wrong or the firewall is not working like it should.

  Read the article

• How can I verify that my SSD is performing as it should?

  - by Jon Skeet

  EDIT: Okay, so I've no idea what caused the change, but after trying loads of different things to work out what was wrong, I've rerun the WEI (about the 4th time in total) and the score has jumped to a far more respectable 7.3. I'm going to leave well alone now :) I've got a brand new 256GB SSD (Crucial CT256M225) which should have stellar performance. However, on my (also brand new) Dell Studio 1557 with Windows 7 Professional 64 bit, it's only giving a performance index of 5.9. I realise the performance index should be taken with a bit of a pinch of salt, but I wonder whether something's wrong. Given this paragraph from this MSDN article on Windows 7, I'd expect to see a high 6.X or possible a 7.X figure: In Windows 7, there are new random read, random write and flush assessments. Better SSDs can score above 6.5 all the way to 7.9. To be included in that range, an SSD has to have outstanding random read rates and be resilient to flush and random write workloads. In the Beta timeframe of Windows 7, there was a capping of scores at 1.9, 2.9 or the like if a disk (SSD or HDD) didn’t perform adequately when confronted with our random write and flush assessments. Feedback on this was pretty consistent, with most feeling the level of capping to be excessive. As a result, we now simply restrict SSDs with performance issues from joining the newly added 6.0+ and 7.0+ ranges. SSDs that are not solid performers across all assessments effectively get scored in a manner similar to what they would have been in Windows Vista, gaining no Win7 boost for great random read performance. How can I diagnose any performance issues with either the disk or how Windows 7 is handling it? Are there any particularly good tools you'd recommend? One note of curiosity: I couldn't install the firmware update (to 1916) until I changed my BIOS handling of the drive to ATA mode; after installing the firmware I tried to boot the Windows installation DVD - but that only worked after turning it back to AHCI mode (which I've left it in). Installing Windows 7 took longer than I expected - it sat at the "Windows is loading files" prompt for a very long time. Likewise it was on "Expanding files (0%)" for a long time. Since installation it's been fine though - but I don't know whether it's really providing quite as beefy performance as it should. EDIT: My netbook with the 64GB equivalent drive has a performance index of 6.6...

  Read the article

• Windows cannot find the host name "download.microsoft.com" using DNS

  - by joedotnot

  When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

  Read the article

• Avoid read-write access to bad sectors on HDD to continue working on the HDD

  - by goldenmean

  I have a HP Pavilion dv6446 notebook. It had Windows Vista Home premium. After 4.5+ years of usage, just recently it started malfunctioning. While working fine, its screen goes white or sometimes some thin black lines horizontally. Laptop freezes. Hard reboot works. Again it works for some 2 hrs or so, same error. To diagnose I did run the Memory and Hard disk check which is present in the Bios Setup. Memory test passed. Hard disk test returned an error saying something like - "Replace the hard disk". Bad.. Some sectors or platters have gone bad on the disk. (I confirmed this later by further tests mentioned below) Then I tried installing a Ubuntu 11.10. It listed 3 partitions /dev/sda1, sda2, sda2. It again gave error and could not install grub loader on /dev/sda1. Bad sectors. Then redid the Ubuntu installation, this time asked to to install the Ubuntu on /dev/sda3. and kept /dev/sda1 for /home. Installed fine, and works fine as well. Due to unavailability of WiFi/ Ethernet driver for that adapters under Ubuntu( at least I could not configure them and get the networking working at all), I decided to go back to reinstall windows Vista. It did install fine. I did not have to format one data partition which has my data. I just formatted one partition which installed Windows So in effect HDD has not undergone a full format here. Worked ok for 1 day. But same white screen and freeze happened. Looks like while it is in use, it accesses the bad sectors for storing some data and that's when it bombs. I am inclined to think HDD has not failed fully or crashed but has developed bad sectors. Else if it was a HDD crash, it would have refused to boot at all let alone install on it. Questions: Is there any HDD test check under windows or any such tools windows/linux based ewhere which can identify the bad sectors of the HDD and 'lock/isolate' them from further read-write access of any kind. If not what are my options, if any to salvage this laptop HDD without replacing it. EDIT: Would the Disk Error checking tool under windows help in any way?

  Read the article

• Strange permission errors with Windows Server 2008

  - by Spirit

  I just don't know a better way to describe my issue that is driving me nuts. I am trying to establish a test domain with virtual machines on a box that has Win7 with VMwware workstation installed. The purpouse with this domain will be so that we can try and test different situations before they go into the production network. I build a VM with WinSrv2008R2 and I am using that VM as a template to make other servers for the domain by making clones of it. Now I raise a DC with one clone and a member server with another clone - I add the server to the domain. I am following a standard procedure as always (it is not my first domain). Then I make an admin account and I am adding the admin to be a member of the Domain and Enterprise Admins group. That admin is admin with full priviledges on the DC.. no problem there. But on the other server has ... somewhat half the privileges and I cant log in via RDP. I tryed with another account. Same issues. For example (with half the privileges): I can't open the Even Viewer if I go via Start - Administrative Tools - Event Viewer. But I can open the Even Viewer via the server manager. You can notice this on the image below. I mean WTF??? I am going crazy, I haven't experienced anything similar in my three years of expertise. I already lost 3 days troubleshooting this. Could this be related with the cloning? Perhaps if I make fresh installs of WinSrv2008 there won't be any problems? I've had raised test domains as VMs on other occasions before, and there weren't any problems then. This is VMware Workstation 8. I've made clones before, on Workstation 7 it didn't had any problems. Anyone has any ideas? UPDATE: This is the info from the event log when I try to access via RDP: An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: pat.coleman Account Domain: lab Failure Information: Failure Reason: Domain sid inconsistent. Status: 0xc000006d Sub Status: 0xc000019b

  Read the article

< Previous Page | 464 465 466 467 468 469 470 471 472 473 474 475  | Next Page >