Search Results

Search found 2110 results on 85 pages for 'don boots'.

Page 47/85 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• Can I change from BIOS IDE mode to AHCI mode at any time?

  - by Software Monkey

  Currently my Windows 7 computer is crashing during startup, after loading the AMD achix64s.sys driver, if I enable BIOS AHCI mode for the disks. It boots fine with IDE mode. Since I need my computer working, I am wondering if I can just use IDE mode for now, and later change to AHCI mode, when I figure out what is wrong. Background: I was running RAID mode, which needed additional drivers to install/boot Windows. But the MoBo RAID is flaky so I'm trying to switch to using a Windows mirrored volume instead - for that I expected to use AHCI mode.

  Read the article

• Lenovo ThinkServer TS130 1105 - does 32/64 depend on RAM?

  - by Ecnerwal

  Just got in a Lenovo ThinkServer TS130 1105 (Xeon E3-1225V1) and a (new, sealed, holographed, looks legit) copy of Windows Server 2008 32/64 (standard) to run on it for a pretty lightweight job (currently handled, adequately, by a terrifyingly old Optima P4 running Windows 2000 server - really lightweight, but long-past-due for replacement, without any particular need or excuse for server 2012...) The 64 bit disc sits there and does nothing. The 32 bit disc boots. I haven't spotted any mention of this in the TS130 Manual (I have now combed it, and find no mention of a need to populate in pairs - a preferred order to populate in, yes, but no mention of pairs being required) but I begin to wonder if it's due to the fact that the 4GB RAM suppled with it was a single DIMM, rather than a pair. Better for upgrading, but perhaps requiring an upgrade (or sidegrade) right away to install the x64 version?? Anyone know? I tried the 64-bit DVD on a desktop with an AMD Athlon II X4 635 processor which normally runs Windows7 in 64 bit, and it booted up just fine.

  Read the article

• Dead-simple USB-based Windows partition cloner?

  - by OverTheRainbow

  Clonezilla is a fine open-source tool, but it requires going through several screens. Since I need to save/restore the same Windows partition, I was wondering if someone knew of a tool (open-source or not) that is easier to use and boots off a USB keydrive. Ideally, it'll save the two commands to save/restore a partition, so I just need to boot the host from the USB key, choose the command, and it'll take care of business. Are there solutions that look like this? Thank you. Edit: Here's one among other articles that shows how to tell CZ to run a script to avoid the multiple screens.

  Read the article

• DISK BOOT FAILURE after upgrading power supply

  - by Phenom

  After upgrading my power supply, I get the following error message when trying to boot into Windows 7. DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER My Windows 7 installation is on a SATA hard drive. I'm able to fix this problem if I hook up my IDE hard drive, then it boots the SATA hard drive fine. I don't like this solution though because then that means my IDE hard drive is drawing power even though it isn't being used. Why would a newer power supply need the IDE hard drive hooked up just to boot into the SATA hard drive? There are no boot files on the IDE hard drive; it is completely empty. My old power supply did not need it hooked up in order to boot the SATA hard drive.

  Read the article

• Boot from Second SATA Drive

  - by Chris

  I have a Dell Precision 490 Workstation, and I just had my other question answered, Install Ubuntu to drive B without impacting drive A, and now I'm having a boot sequence issue. The external drive is great, boots up fine on my laptop, but how do I tell my desktop to boot from my second SATA drive and not the first SATAdrive. My drive configuration as follows SATA-0: Windows SATA-1: DVDR SATA-2: Ubuntu When I choose the boot menu, the option I have is "Internal Hard Drive". I assume it searches all drives, and loads the first bootable one it finds (which happens to be Windows), but I'd like to be able to select the drive from a list. Has anyone experienced this? Is possible without disabling the first hard drive in the BIOS?

  Read the article

• Setting WMI permissions remotely on windows server 2003

  - by user41507

  Hello. I am a programmer , I don know the server well. I made a simple program checking the service on the remote server is started or not. by using this(http://msdn.microsoft.com/en-us/library/dwd0y33x(v=VS.90).aspx) but the permission should be set. and I can't find any document via the internet. except one document. http://msdn.microsoft.com/en-us/library/aa393266(VS.85).aspx but the engineer say that 'tell me exactly what I do. there are many DCOM are they any nice document to show him? thanks in advance

  Read the article

• How to select the account on the login screen of Windows7 by start typing the name?

  - by akira

  When MacOS boots up and the users is prompted to select the account (s)he wants to login into, the users can either click the name / icon of the account with the mouse or just type in the name of the account. I want to do the same at the login screen of Windows7: Login screen pops up, I start to type my account name, I select the account with enter and then I type the password and enter again. No usage of the mouse involved. (I am aware of tab-cycling and hard-to-follow-the-almost-invisible-marker-of-where-the-focus-is-right-now)

  Read the article

• Xen find VBD id for physical disks

  - by Joe

  I'm starting a xen domU using xm create config.cfg. Within the config file are a number of physical block devices (LVs) which are added to the guest and can be accessed fine when it boots. However, at a point in the future I need to be able to hot unplug one of these disks using the xm block-detach command. This command, however, requires the vbd id of the device to be detached and I can't find a way to find the device id for a particular disk 'plugged in' at start up. Any help is much appreciated!

  Read the article

• How to turn ON bluetooth in Dell Inspiron?

  - by ykombinator

  I bought a new Dell Inspiron laptop a month ago. The company had pre-installed all the required software in my laptop. As such, the bluetooth used to be switched ON whenever I switched on my machine. However, a few days later, the bluetooth stopped working. I re-started the Laptop and it was ON! Now I am facing this problem very frequently. As such, the wi-fi connection doesn't work unless the bluetooth is switched ON. The bluetooth turns ON after a few re-boots and sometimes doesn't turn ON for many days. Does anybody know any trick to keep the bluetooth ON everytime I switch ON my machine. P.S: The Dell manual did not help.

  Read the article

• PS/2 mouse works with Windows 7 32-bit but not recognised by 64-bit, What to do?

  - by Bogan

  Our USB mouse was stolen and a PS/2 OK_520 Mouse that works OK on my Medion PC, running Windows 7 32-bit, if plugged in before booting, is not recognised by Windows 7 64-bit on a Dell INSPIRONone_19T with a 19" Touch Screen. (It is a communal computer available to all residents.) A USB mouse works OK and the Update Driver option reports: 'driver is up to date'. Without the USB Mouse, Device Manager/Mice shows only the Touch Screen as a Mouse. The Add New Hardware option searches but shows nothing and the Troubleshooter says ' device possibly not recognised, alterations made to system, try again.' but it is still not recognised after repeated re-boots. The BIOS does not seem to have any option to enable a PS/2 Mouse. The Mouse is very old so maybe it is not 64-bit compatible, or there is no 64-bit driver for one, but how to get one if the device is not recognised?

  Read the article

• Can Grub be configured to remember the last OS you booted into?

  - by Matthew

  I typically have 2-3 OSes in my boot menu: Ubuntu 10.04 Windows 7 [Sometimes, a third option, such as Ubuntu 10.04 Netbook] If I am in an OS other than the default choice (Windows 7 in this case), and I reboot, Grub boots into Ubuntu 10.04. This shouldn't happen--when I reboot in Windows 7, I want to stay in Windows 7. Is there any way to configure Grub to remember my last choice, and boot into that? Alternatively, it would be even better if Grub only did this when I rebooted (not when I first turn the computer on). I realize this may not be possible, so I'd be happy with simple last-choice-remembering.

  Read the article

• iMac with Mountain Lion and Mavericks

  - by bob

  I have been starting up my iMac (Mavericks) with a flash drive that boots up Mountain Lion so that I can use an app that is incompatible with Mavericks. Question: I have a single external backup drive always connected to my Mac. I am thinking of partitioning that drive and giving each partition a unique name, e.g., Backup 1 and Backup 2. I intend then to boot up in Mavericks and tell Time Machine to back up to Backup 1, and then boot up in Mountain Lion and tell Time Machine to back up to Backup 2. Will this work, i.e., will the appropriate partition automatically back up the system in which it is booted?

  Read the article

• How do I mount a sparse disk image permanently?

  - by Mike

  On Mac OS X 10.6.7, when I mount a sparse disk image (either by double-clicking it or using hdid from the command line), the image: Appears on my desktop Needs to be re-mounted every time I log in I'd like to set up the equivalent of an /etc/fstab which will mount the image when the system boots, and make it permanent - so I don't have to worry if my symbolic links will resolve or not. Is this more trouble than it's worth on a Mac? I noticed that there is no /etc/fstab, and /etc/fstab.hd contains a dire warning: IGNORE THIS FILE. This file does nothing, contains no useful data, and might go away in future releases. Do not depend on this file or its contents. I tried sudo hdid -notremovable <image>, which seemed like half of what I wanted (according to man hdid), but it failed with an error: hdid: attach failed - no mountable file systems.

  Read the article

• what's the difference between /etc/init.d/sshd start and /usr/sbin/sshd?

  - by jasono

  I'm having issues with passwordless ssh. I've checked, double checked and checked again that I have everything set up correctly. Both machines are RHEL6 and when the destination machine first boots up passwordless ssh does not work. If I stop ssh (service sshd stop or /ect/init.d/sshd stop) and then start it directly (/usr/sbin/sshd) passwordless ssh works fine. If I start ssh via the service (service sshd start or /etc/init.d/sshd start) passwordless ssh does not work. Just for testing I've tried commenting out the entire start() function in /etc/init.d/sshd and replace it with /usr/sbin/sshd - that still fails to allow passwordless ssh. I believe that this means that something in the /etc/init.d/sshd file is causing the screw up but I don't know enough about linux to narrow the issue down.

  Read the article

• ATI Radeon Drivers works with which linux distribution and version? [closed]

  - by amit.codename13

  I have ATI Mobility Radeon HD 5850 graphics card. Almost every new linux distribution seems to have an issue with it, when i install the drivers. Working without utilizing the graphics card leaves me so unproductive. So i made a plan to use older versions of linux, any distribution suitable as a desktop distribution. The problems that i am facing are, 1) After installing drivers the system boots and hangs, 2) There are unusual lines over the screen 3) After upgrade system doesn't start properly(hangs the usual old way) The kind of answers i am looking for is, distribution X(the newer the version the better) doesn't have the above problem after installing drivers for ATI Mobility Radeon HD 5850 graphics card. UPDATE: The new drivers released by AMD seems to fix all the issues, although they are still beta

  Read the article

• How do I permanently disable Linux's console screen saver, system-wide?

  - by raldi

  I've got an Ubuntu server that boots up in text mode. It rarely has a screen or keyboard attached to it, but when I do attach a screen, I usually have to attach a keyboard too, because the darn console mode screen saver will be on and I'll need to hit a key to see what's going on. I'm aware that the setterm command can disable this, but it's a per-session thing. How can I make it so the machine never ever blanks the screen in text mode, even when it's first booted up and sitting at the login prompt?

  Read the article

• Cron process not starting

  - by vkris

  I have an ec2 image created with cron jobs. These jobs fail to run; I discovered the cron process in itself has not started. So, I included /usr/sbin/cron in /etc/rc.d/rc.local and created another image. But still for some reason the cron process does not start on bootup. If I restart the machine, the cron process runs. It doesn't run when it boots up! Any reason why this is happening? Also, is there any other alternatives for this ?

  Read the article

• How to install Windows 8 boot manager in a different partition?

  - by arnab321

  the last time i installed Windows 7, the boot manager automatically got installed in a small hidden partition, and the main os into another partition. So, formatting the c: won't affect the boot manager. yesterday i wiped and repartitioned my hdd like this: 50mb primary ntfs (meant for boot manager) 100gb primary ntfs (for win 8) 50gb primary ntfs (for win 7) some logical partitions to install ubuntu and other os i installed win 7 and then win 8, and now there is no os choosing menu. system directly boots win 8 and the 50 mb partition is empty. There is a way to boot Windows 7 and even Ubuntu directly from the Windows boot manager with EasyBCD. But How do i put the boot manager in the 50mb partition ?

  Read the article

• Can GnomeKeyring store passwords unencrypted?

  - by antimeme

  I have a Fedora 15 laptop with the root and home partitions encrypted using LUKS. When it boots I have to enter a pass phrase to unlock the master key, so I have it configured to automatically log me in to my account. However, GnomeKeyring remains locked, so I have to enter another pass phrase for that. This is unpleasant and completely pointless since the entire disk is encrypted. I've not been able to find a way to configure GnomeKeyring to store its pass phrases without encryption. For example, I was not able to find an answer here: http://library.gnome.org/users/seahorse-plugins/stable/index.html.en Is there a solution? If not, is there a mailing list where it would be appropriate to plead my case?

  Read the article

• Flashing cursor with new laptop battery

  - by Fuzzy Purple Monkey

  I recently purchased a new, non-Toshiba battery for my Toshiba M700 tablet/laptop. The battery fits fine and the tablet detects and charges it, but when I try to boot up all I get is the Toshiba logo then a flashing cursor in the top-left. I can get to the bios, but no further. If I put the old battery back in, everything boots up fine. Has anyone else seen this problem? What am I missing? Thanks in advance!

  Read the article

• PSU aka Power Supply won't turn off and No Power_Good - Safe to keep using?

  - by Tek

  The title is the symptoms of my problem. I mainly chose this title for search engines so people can know why this is happening since I see a lot of uncertainty when it comes to this problem. I do have a question related to the source of the problem though. First of all, Inserting the power to the power supply automatically turns on my computer. Using a power supply tester, the tester automatically turns on without me having to push the button to test the PSU. lol. The PG (Power Good) signal is missing. The strange thing is my computer still turns on (OS boots, etc) considering a missing power good signal. Is it really that unsafe to use the power supply when it's missing the power good signal? All the voltages seem to be in check. Here's a picture: Power Supply Tester Readout And by safe (considering the readout) in the sense that is it likely my components (cpu, mobo, etc) could be damaged?

  Read the article

• Keyboard not responding on startup

  - by Mestika

  I’m having a weird problem with one of the laptops at my work. Every now and then (not a systematic repeating pattern, but kind of random) the keyboard will not function on start up. The computer boots and it gets to the CTRL + ALT + DELETE screen and it is responding to nothing from the keyboard. The mouse works fine. I then try to force a shutdown and reboot the machine and most of the time it then works. My first thought was that it was a hardware malfunction with the keyboard hardware but it seems strange that the computer can be stationed for several days without being removed and it still “loses” connection to the keyboard. The OS is Windows 7 Pro and it is a Dell Laptop Vostro. Does anyone experienced this kind of problem with a laptop with/with out Windows 7 and maybe got a solution to the problem?

  Read the article

• HP Pavillion dv6 laptop - 15 beeps on startup and a black screen?

  - by dunc

  Usual story - girlfriend's step-brother's laptop is broken. I don't know a huge amount about what occurred before it broke, but I do know the following: When you try to turn the laptop on, it beeps 15 times exactly. The screen remains black. The LED on the Caps Lock key flashes continuously. If left on, the laptop never boots - as far as I can see. If left on, on a stable surface with decent ventilation for a relatively short period of time, the laptop (below keyboard, but not where the RAM/HDD are) gets very hot. I've tried doing what most websites appear to recommend for similar problems, which is to disconnect AC and battery then hold the power button down for a minute before reconnecting the AC and trying to turn the laptop on - no difference. EDIT I've also tried re-seating the RAM, to no avail. Any ideas? Thanks in advance,

  Read the article

• Cisco 1760 T1 Setup

  - by Joseph

  My 1760 has a WIC1-T1 card in Slot 0 and the slot 0 "OK" light is lit. When the router boots it shows that it sees the T1 card. I would like to configure my T1. I received the following details from my ISP: * Removed IP's IP Version: IPv4 Router Interface: edge1.mia1 -- t1-2/1/0:2:13 -- Switch Port: Vlan: WAN Network: 4.59.?.?/30 Level3 Side: 4.59.?.? Customer Side: 4.59.?.? Cust. LAN IPs: 4.59.?.?/27 The problem is that it is not listed under interfaces. I am a noob with IOS, please let me know if you need more details. Thanks.

  Read the article

• Lost Linux root password - Recovery mode and init=/bin/bash fail

  - by Albeit

  I lost/forgot the root password to a server sitting beside me and am trying to reset it. I would rather not have to wipe and re-install or use a Live CD (server is running Ubuntu Server 12.04). What I've tried so far... 1) Boot into "Recovery mode" from Grub2 boot menu then drop into root shell prompt. I am prompted to "Give root password for maintenance". No-go. 2) Change the boot parameters for the main boot option to include "rw" and "init=/bin/bash". When I then boot with Ctrl-X, the screen goes black, and nothing happens (I've waited five minutes). init=/bin/sh and init=/bin/static-sh both do the same thing, while init=/sbin/init boots as normal. Is there anything else I can try to reset the root password? Thank you!

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >