Search Results

Search found 15634 results on 626 pages for 'foreach loop container'.

Page 47/626 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• Unity: How to remove(unregister) registered instance from Unity mapping.

  - by bug0r

  Hello, I meet one problem that i can't solve now. I have the following: UnityHelper.DefaultContainer.RegisterInstance(typeof(IMyInterface), "test", instance); where UnityHelper.DefaultContainer is my helper for getting unity container with loaded configuration. here I registered instance as an instance of IMyInterface. So anywhere(some time after using) I want to remove this mapping. Remove it at all. How I can do it? I have tried UnityHelper.DefaultContainer.Teardown(instance) but is was unsuccessfull and the following code returns instance anyway. UnityHelper.DefaultContainer.ResolveAll() Any ideas? Thank you.

  Read the article

• How does Unity.Resolve know which constructor to use?

  - by stiank81

  Given a class with several constructors - how can I tell Resolve which constructor to use? Consider the following example class: public class Foo { public Foo() { } public Foo(IBar bar) { Bar = bar; } public Foo(string name, IBar bar) { Bar = bar; Name = name; } public IBar Bar { get; set; } public string Name { get; set; } } If I want to create an object of type Foo using Resolve how will Resolve know which constructor to use? And how can I tell it to use the right one? Let's say I have a container with an IBar registered - will it understand that it should favor the constructor taking IBar? And if I specify a string too - will it use the (string, IBar) constructor? Foo foo = unityContainer.Resolve<Foo>(); And please ignore the fact that it would probably be easier if the class just had a single constructor...

  Read the article

• DDD and IOC Containers

  - by MegaByte

  Hi Im fairly new with DDD and Im trying to use IOC in order to loosen up my tightly coupled layers :) My C# web application consists of a UI, domain and persistence layer. My persistence layer references my domain layer and contains my concrete repository implementations and nhibernate mappings. Currently my UI references my domain layer. My question : How do I use an IOC container to inject my concrete classes, in my persistence layer, into my domain layer? Does this meen that my UI should also reference my persistence layer?

  Read the article

• Are IoC containers about configuration files?

  - by Jader Dias

  Recently I developed a performance tester console application, with no UI, with the help of a IoC containter (Castle-Windsor-Microkernel). This library enabled me to let the user choose which test(s) to run, simply by changing the configuration file. Have I realized what IoC containers are about? I'm not sure. Even Joel said here on SO that IoC are difficult to understand. From my example, what do you conclude? Am I using IoC container for exactly what they were designed for? Or I am just using one of its secondary features?

  Read the article

• how to implement IOC without a global static service (non-service locator solution)?

  - by Michel

  Hi, we want to use Unity for IOC. All i've seen is the implementation that there is one global static service which holds a reference to the Unity container, which registers all interface/class combinations and every class asks that object: give me an implementation for Ithis or IThat. Frequently i see a response that this pattern is not good because it leads to a dependency from ALL classes to this service. But what i don't see often, is: what is the alternative way? Michel EDIT: found out that the global static service is called the service locator, added that to the title.

  Read the article

• Does the chunk of the System.Collections.Concurrent.Partitioner need to be thread safe?

  - by Scott Chamberlain

  I am working with the Parallel libraries in .net 4 and I am creating a Partitioner and the example shown in the MSDN only has a chunk size of 1 (every time a new result is retrieved it hits the data source instead of the local cache. The version I am writing will pull 10000 SQL rows at a time then feed the rows from the cache until it is empty then pull another batch. Each partition in the Partitioner has its own chunk. I know every time I call to the IEnumerator in from the SQL data-source that needs to be thread safe but for use in a Parallel.ForEach do I need to make every call to the cache for the chunking thread safe?

  Read the article

• Which containers / graphics components to use in a simple Java Swing game?

  - by rize

  I'm creating a simple labyrinth game with Java + Swing. The game draws a randomized labyrinth on the screen, places a figure in the middle, and the player is then supposed to find the way out by moving the figure with arrow-keys. As for now, I'm using a plain background and drawing the walls of the labyrinth with Graphics.drawLine(). I have a custom picture of the figure in a .gif file, which I load as a BufferedImage object. However, I want the player to see only part of the labyrinth at a time, and the screen should follow the figure in the game, as the player moves around. I'm planning to do this by creating an Image object of the whole labyrinth when it is created, and then "cutting" a square around the current position of the figure and displaying this with Graphics.drawImage(). I'm new with Swing though, and I can't figure out how to draw the figure at different positions "above" the labyrinth without redrawing the whole thing. Which container/component should I use for the labyrinth and then for the figure to achieve this?

  Read the article

• gridview check duplicates not using sql

  - by Tomasusa

  I have a code: foreach (GridViewRow dr in gvCategories.Rows)<br/> { <br/> if (dr.Cells[0].Text == txtEnterCategory.Text.Trim())<br/> <br/> isError=true; <br/> <br/> } Debugging: dr.Cells[0].Text is always "", even there are records. How to use a loop to check each row to find if a record exists in the gridview not using sql?

  Read the article

• Is converting this ArrayList to a Generic List efficient?

  - by Greg

  The code I'm writing receives an ArrayList from unmanaged code, and this ArrayList will always contain one or more objects of type Grid_Heading_Blk. I've considered changing this ArrayList to a generic List, but I'm unsure if the conversion operation will be so expensive as to nullify the benefits of working with the generic list. Currently, I'm just running a foreach (Grid_Heading_Blk in myArrayList) operation to work with the ArrayList contents after passing the ArrayList to the class that will use it. Should I convert the ArrayList to a generic typed list? And if so, what is the most efficient way of doing so?

  Read the article

• StructureMap 'conditional singleton' for Lucene.Net IndexReader

  - by Gareth D

  I have a threadsafe object that is expensive to create and needs to be available through my application (a Lucene.Net IndexReader). The object can become invalid, at which point I need to recreate it (IndexReader.IsCurrent is false, need a new instance using IndexReader.Reopen). I'd like to able to use an IoC container (StructureMap) to manage the creation of the object, but I can't work out if this scenario is possible. It feels like some kind of "conditional singleton" lifecycle. Does StructureMap provide such a feature? Any alternative suggestions?

  Read the article

• Cannot access data in a xml string

  - by Jess McKenzie

  I am trying to create an array that I can include the perent category Name and the child category Name. I can so far access the below object fine using $xml->Subcategories; but if I try my code below I get an empty array why? PHP: foreach ($catDetailsXml->Category as $value) { $categoryDetails[] = array('CategoryNumber' => $value->Number); } Structure: object(SimpleXMLElement)#13 (1) { ["Category"]=> array(5) { [0]=> object(SimpleXMLElement)#14 (4) { ["Name"]=> string(19) "Commercial Property" ["Number"]=> string(10) "0350-0100-" ["Subcategories"]=> object(SimpleXMLElement)#35 (1) { ["Category"]=> array(3) { [0]=> object(SimpleXMLElement)#36 (4) { ["Name"]=> string(9) "Car parks" ["Number"]=> string(15) "0350-0100-8946-" ["Subcategories"]=> object(SimpleXMLElement)#39 (0) { } }

  Read the article

• Codeigniter view file looping query

  - by user2505513

  Right, I'm unsure about how to code my view file to generate following query results WITHOUT compromising the principles of mvc. Query in model: SELECT * FROM events GROUP BY country, area ORDER BY country, area View: <?php if (isset($query)):?> <?php foreach ($query as $row):?> <h2><?=$row->country?></h2> <h3><?=$row->area?></h3> <?php endforeach;?> <?php endif;?> I want the results to display: England North South West - utilising the GROUP BY parameter As opposed to: England North England South England West Has anybody any advice as to how to achieve this?

  Read the article

• There has to be an easier way.. pulling data from mysql

  - by Daniel Hunter

  I need to pull 3 values from a table and assign each one to a variable each value is based on to columns, a type and an id $ht_live_query = mysql_query("SELECT htcode FROM coupon WHERE pid='$pid' AND type='L'"); $ht_live_result = mysql_fetch_array($ht_live_query); $htCODE_Live = $ht_live_result['htcode']; You can see that I am assigning the desired value to the variable $htL $ht_General_query = mysql_query("SELECT htcode FROM coupon WHERE pid='$pid' AND type='G'"); $ht_General_result = mysql_fetch_array($ht_General_query); $htCODE_General = $ht_General_result['htcode']; $ht_Reward_query = mysql_query("SELECT htcode FROM coupon WHERE pid='$pid' AND type='R'"); $ht_Reward_result = mysql_fetch_array($ht_Reward_query); $htCODE_Reward = $ht_Reward_result ['htcode']; I know I am doing this the hard way but can not figure out how to do the foreach or while loop to attain the desired results.

  Read the article

• Concatenating a Text in front of Individual Database Records with Tcl

  - by DFM

  Hello: In short, currently I am using the following code to pull records from multiple tables in a Sqlite Db and insert them in a single combobox ($SearchBar): set SrchVals1 [db eval {SELECT DISTINCT Stitle From Subcontract Order By Stitle ASC}] set SrchVals2 [db eval {... set SrchVals3 ... set SrchValsALL [concat $SrchVals1 $SrchVals2 $SrchVals3] $SearchBar configure -value $SrchValsAll For the variable "SrchVals1", I am trying to figure out a way to concatenate the text "Sub: " to each individual record in SrchVals1. For example, if SrchVals1 shows the following records in the combobox: First Title Second Title Third Title I would like to concatenate so that the records in the combobox look like this: Sub: First Title Sub: Second Title Sub: Third Title I understand that I might have to use a foreach statement; however, I am having no luck writing one that adds "Sub: " in front of each record, as opposed to one. This seems like something that should be pretty easy, but I cannot seem to figure it out. Does anyone know how I can achieve these results? Thank you, DFM

  Read the article

• DI: Injecting ActionFilterAttribute implementation (ASP.NET MVC)

  - by Sosh

  I was wondering if it is possible to inject a particular ActionFilterAttribute implementation using a IoC container. For example, imagine you create a TransactionAttribute class [Transaction] You use this to decorate action which should be wrapped in a transaction in the persistence layer. But implementation details of the attribute will be tied to the persistence tech you are using, but strictly speaking, your controller should not know about this, and you might want to swap this out. What I would like to do, is define some kind of TransactionAttribute interface, and then have my IoC inject the correct implantation. So on my actions I only need specify: [Transaction] public ActionResult SomeAction() { .... } ...and the IoC will inject the correct implementation depending on config (eg. something like NHibernateTransactionAttribute, or SomeOtherORMTransactionAttribute). Is this possible? Has anyone done it?

  Read the article

• PHP from database and query

  - by Kyle R

  I have a table: id, affiliate Each time somebody clicks a link, a new row is inserted, ID being the ID of the page, and affiliate being the ID of the affiliate. For example: Page ID: 9 Affiliate ID: 1 Page ID: 9 Affiliate ID: 2 Page ID: 9 Affiliate ID: 3 I only have 3 affiliates. I want to select this information, and group them by affiliate, for the ID. I have tried this query: SELECT COUNT(*) FROM table WHERE id = '9' GROUP BY affiliate It works fine when I do it in php my admin, how do I get the info in PHP? I have tried: $q = mysql_query("SELECT COUNT(*) FROM table WHERE id = '" . $id . "' GROUP BY affiliate"); $r = mysql_fetch_array($q); When trying to print the data onto the page, I am only getting one result. Do I need to use a foreach/while loop to get all 3? How would I go about doing this? Thank you!

  Read the article

• Weird vps server issue

  - by anon-user0

  I have an unmanaged linux vps Ubuntu 11.10 (Oneiric Ocelot). I have LNMP installed. Also php-fpm php-apc, varnish, memcache. I have (or rather had) several live sites on it. under normal load the server uses ~700 mb memory. But since last night its using only 20mb~ memory and a lot of the services seems to be down (according to htop) I only see nginx working and mysql starts up and goes does every few minutes on a loop. Here are some information on the server that might help you help me: root@server:~# uname -a Linux server 2.6.18-308.el5.028stab099.3 #1 SMP Wed Mar 7 15:56:00 MSK 2012 i686 i686 i386 GNU/Linux - root@server:~# ifconfig -a lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:12515 errors:0 dropped:0 overruns:0 frame:0 TX packets:9541 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7191214 (7.1 MB) TX bytes:536726 (536.7 KB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:176.31.158.78 P-t-P:176.31.158.78 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 - root@server:~# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:http-alt *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp6 0 0 [::]:http-alt [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 9307368 @/com/ubuntu/upstart - htop: http://i.stack.imgur.com/NHKYX.png EDIT: Stressed. mind was not working adding log: root@server:~# less /var/log/syslog Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:39:01 server CRON[9298]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 05:40:01 server CRON[9463]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 05:46:21 server sm-msp-queue[9480]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:19:14, xdelay=00:06:18, mailer=relay, pri=122407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 05:52:39 server sm-msp-queue[9480]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:06:32, xdelay=00:06:18, mailer=relay, pri=842407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:00:01 server CRON[15671]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:06:22 server sm-msp-queue[15690]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:39:15, xdelay=00:06:18, mailer=relay, pri=212407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:09:01 server CRON[18114]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:12:40 server sm-msp-queue[15690]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:26:33, xdelay=00:06:18, mailer=relay, pri=932407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:20:02 server CRON[21888]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:26:22 server sm-msp-queue[21907]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:59:15, xdelay=00:06:18, mailer=relay, pri=302407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:27:02 server CRON[24021]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 06:32:40 server sm-msp-queue[21907]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:46:33, xdelay=00:06:18, mailer=relay, pri=1022407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:39:01 server CRON[27941]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:40:02 server CRON[28110]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:46:22 server sm-msp-queue[28125]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:19:15, xdelay=00:06:18, mailer=relay, pri=392407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:06:33, xdelay=00:06:18, mailer=relay, pri=1112407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: q5R2e4uo028125: sender notify: Warning: could not send message for past 4 hours Jun 27 06:52:44 server sm-msp-queue[28125]: q5R2e4uo028125: to=root, delay=00:00:04, xdelay=00:00:04, mailer=relay, pri=33690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:00:02 server CRON[1543]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:06:21 server sm-msp-queue[1560]: q5R2e4uo028125: to=root, delay=00:13:41, xdelay=00:06:18, mailer=relay, pri=123690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:09:01 server CRON[3986]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 07:12:39 server sm-msp-queue[1560]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:45:32, xdelay=00:06:18, mailer=relay, pri=482407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:18:57 server sm-msp-queue[1560]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:32:50, xdelay=00:06:18, mailer=relay, pri=1202407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:20:02 server CRON[7760]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:26:22 server sm-msp-queue[7775]: q5R2e4uo028125: to=root, delay=00:33:42, xdelay=00:06:18, mailer=relay, pri=213690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:27:01 server CRON[9887]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 07:32:40 server sm-msp-queue[7775]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=02:05:33, xdelay=00:06:18, mailer=relay, pri=572407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:38:58 server sm-msp-queue[7775]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:52:51, xdelay=00:06:18, mailer=relay, pri=1292407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:39:01 server CRON[13813]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth : root@server:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/simfs 20G 2.3G 18G 12% / - Jun 26 16:22:41 server varnishd[1413]: Child (32425) died signal=3 Jun 26 16:22:41 server varnishd[1413]: child (21687) Started Jun 26 16:22:41 server varnishd[1413]: Child (21687) said Child starts Jun 26 16:22:41 server varnishd[1413]: Child (21687) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 26 16:34:28 server -- MARK -- Jun 26 16:54:29 server -- MARK -- Jun 26 17:14:29 server -- MARK -- Jun 26 17:34:29 server -- MARK -- Jun 26 17:54:29 server -- MARK -- Jun 26 18:14:29 server -- MARK -- Jun 26 18:34:29 server -- MARK -- Jun 26 18:54:29 server -- MARK -- Jun 26 19:14:29 server -- MARK -- Jun 26 19:34:29 server -- MARK -- Jun 26 19:54:29 server -- MARK -- Jun 26 20:14:29 server -- MARK -- Jun 26 20:34:29 server -- MARK -- Jun 26 20:48:12 server exiting on signal 15 Jun 26 20:51:58 server syslogd 1.5.0#6ubuntu1: restart. Jun 26 20:52:01 server varnishd[1324]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 26 21:11:58 server -- MARK -- Jun 26 21:31:58 server -- MARK -- Jun 26 21:51:58 server -- MARK -- Jun 26 22:11:58 server -- MARK -- Jun 26 22:31:58 server -- MARK -- Jun 26 22:51:58 server -- MARK -- Jun 26 23:11:58 server -- MARK -- Jun 26 23:31:58 server -- MARK -- Jun 26 23:51:58 server -- MARK -- Jun 27 00:11:58 server -- MARK -- Jun 27 00:23:42 server exiting on signal 15 Jun 27 02:21:10 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 02:21:12 server varnishd[1341]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 02:41:10 server -- MARK -- Jun 27 02:46:41 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:44 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:46 server varnishd[1238]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:20:46 server varnishd[1238]: child (1239) Started Jun 27 03:20:46 server varnishd[1238]: Child (1239) said Child starts Jun 27 03:20:46 server varnishd[1238]: Child (1239) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 27 03:32:52 server exiting on signal 15 Jun 27 03:33:16 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:33:31 server varnishd[1372]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:53:16 server -- MARK -- Jun 27 04:13:16 server -- MARK -- Jun 27 04:33:16 server -- MARK -- Jun 27 04:53:16 server -- MARK -- Jun 27 05:13:16 server -- MARK -- Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:53:17 server -- MARK -- Jun 27 06:13:17 server -- MARK -- Jun 27 06:33:17 server -- MARK -- Jun 27 06:53:17 server -- MARK -- Jun 27 07:13:17 server -- MARK -- Jun 27 07:33:17 server -- MARK -- Jun 27 07:53:17 server -- MARK -- Jun 27 08:13:17 server -- MARK -- Jun 27 08:33:17 server -- MARK -- Jun 27 08:53:17 server -- MARK -- Jun 27 09:13:17 server -- MARK -- Jun 27 09:33:17 server -- MARK -- Jun 27 09:53:17 server -- MARK -- Jun 27 10:13:17 server -- MARK -- Jun 27 10:33:17 server -- MARK -- Jun 27 10:53:17 server -- MARK -- Jun 27 11:13:17 server -- MARK -- Jun 27 11:33:17 server -- MARK -- Jun 27 11:53:18 server -- MARK -- Jun 27 12:13:18 server -- MARK -- Jun 27 12:33:18 server -- MARK -- Jun 27 12:53:18 server -- MARK -- Jun 27 13:13:18 server -- MARK -- Jun 27 13:33:18 server -- MARK -- Jun 27 13:53:18 server -- MARK -- Jun 27 14:13:18 server -- MARK -- Jun 27 14:33:18 server -- MARK -- Jun 27 14:53:18 server -- MARK -- -- root@server:~# cat /var/log/nginx/error.log 2012/06/27 03:32:54 [alert] 1199#0: worker process 1203 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1200 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1201 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1202 exited on signal 9 root@server:~# cat /var/log/nginx/access.log 31.210.99.87 - - [27/Jun/2012:09:09:08 +0400] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 172 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cms/cmx.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /iesvc/iesvc.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cmd2/index.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:09 +0400] "GET /cmd/index.jsp HTTP/1.1" 301 184 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:19 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:37 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:48 +0400] "-" 400 0 "-" "-" - root@server:~# cat /var/log/daemon.log Jun 26 20:48:10 server xinetd[1177]: Exiting... Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 26 20:51:58 server xinetd[1174]: Started working: 0 available services Jun 26 20:52:01 server vnstatd[1330]: vnStat daemon 1.11 started. Jun 26 20:52:01 server vnstatd[1330]: Monitoring: venet0 Jun 27 00:23:41 server xinetd[1174]: Exiting... Jun 27 02:21:12 server vnstatd[1349]: vnStat daemon 1.11 started. Jun 27 02:21:12 server vnstatd[1349]: Monitoring: venet0 Jun 27 03:20:44 server xinetd[1166]: attribute: disable should not be in default section [file=/etc/xinetd.conf] [line=12] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/chargen [file=/etc/xinetd.conf] [line=15] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 27 03:20:44 server xinetd[1166]: Started working: 0 available services Jun 27 03:20:46 server vnstatd[1249]: vnStat daemon 1.11 started. Jun 27 03:20:46 server vnstatd[1249]: Monitoring: venet0 Jun 27 03:32:41 server xinetd[1166]: Exiting... Jun 27 03:33:32 server vnstatd[1380]: vnStat daemon 1.11 started. Jun 27 03:33:32 server vnstatd[1380]: Monitoring: venet0 root@server:~# - Anything else you need let me know

  Read the article

• ASP.net Ajax tab container not appearing

  - by Eyla

  I created new web project using VS 2008 with enabled Ajax template with C# and Framework 3.5. I added Ajax reference to the project and I can see all Ajax toolkit in my tool box. The problem that when I add tab container with Tab Panels then run the projects nothing appear on the browser and I tried few browsers. I'm including my code and I wish that someone would help me. Regards, My Code: ................................................................ <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="Default.aspx.cs" Inherits="Contacts._Default" %> <%@ Register assembly="AjaxControlToolkit" namespace="AjaxControlToolkit" tagprefix="asp" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" > <head runat="server"> <title>Untitled Page</title> </head> <body> <form id="form1" runat="server"> <asp:ScriptManager ID="ScriptManager1" runat="server" /> <div> <asp:TabContainer ID="TabContainer1" runat="server" ActiveTabIndex="0"> <asp:TabPanel runat="server" HeaderText="TabPanel1" ID="TabPanel1"> <ContentTemplate> tab 1 </ContentTemplate> </asp:TabPanel> <asp:TabPanel runat="server" HeaderText="TabPanel2" ID="TabPanel2"> <ContentTemplate> tab 2 </ContentTemplate> </asp:TabPanel> <asp:TabPanel runat="server" HeaderText="TabPanel3" ID="TabPanel3"> <ContentTemplate> tab 3 </ContentTemplate> </asp:TabPanel> </asp:TabContainer> </div> </form> </body> </html>

  Read the article

• Iterator failure while moving over equal_range in Boost MultiIndex container

  - by Sarah

  I'm making some mistake with my iterators, but I can't see it yet. I have a Boost MultiIndex container, HostContainer hmap, whose elements are boost::shared_ptr to members of class Host. All the indices work on member functions of class Host. The third index is by Host::getHousehold(), where the household member variable is an int. Below, I'm trying to iterate over the range of Hosts matching a particular household (int hhold2) and load the corresponding private member variable Host::id into an array. I'm getting an "Assertion failed: (px != 0), function operator-, file /Applications/boost_1_42_0/boost/smart_ptr/shared_ptr.hpp, line 418" error in runtime when the household size is 2. (I can't yet tell if it happens anytime the household size is 2, or if other conditions must be met.) typedef multi_index_container< boost::shared_ptr< Host >, indexed_by< hashed_unique< const_mem_fun<Host,int,&Host::getID> >, // 0 - ID index ordered_non_unique< const_mem_fun<Host,int,&Host::getAgeInY> >, // 1 - Age index ordered_non_unique< const_mem_fun<Host,int,&Host::getHousehold> > // 2 - Household index > // end indexed_by > HostContainer; typedef HostContainer::nth_index<2>::type HostsByHH; // inside main() int numFamily = hmap.get<2>().count( hhold2 ); int familyIDs[ numFamily ]; for ( int f = 0; f < numFamily; f++ ) { familyIDs[ f ] = 0; } int indID = 0; int f = 0; std::pair< HostsByHH::iterator, HostsByHH::iterator pit = hmap.get<2().equal_range( hhold2 ); cout << "\tNeed to update households of " << numFamily << " family members (including self) of host ID " << hid2 << endl; while ( pit.first != pit.second ) { cout << "Pointing at new family member still in hhold " << ((pit.first))-getHousehold() << "; " ; indID = ((pit.first) )-getID(); familyIDs[ f ] = indID; pit.first++; f++; } What could make this code fail? The above snippet only runs when numFamily 1. (Other suggestions and criticisms are welcome too.) Thank you in advance.

  Read the article

• Idiomatic use of auto_ptr to transfer ownership to a container

  - by heycam

  I'm refreshing my C++ knowledge after not having used it in anger for a number of years. In writing some code to implement some data structure for practice, I wanted to make sure that my code was exception safe. So I've tried to use std::auto_ptrs in what I think is an appropriate way. Simplifying somewhat, this is what I have: class Tree { public: ~Tree() { /* delete all Node*s in the tree */ } void insert(const string& to_insert); ... private: struct Node { ... vector<Node*> m_children; }; Node* m_root; }; template<T> void push_back(vector<T*>& v, auto_ptr<T> x) { v.push_back(x.get()); x.release(); } void Tree::insert(const string& to_insert) { Node* n = ...; // find where to insert the new node ... push_back(n->m_children, auto_ptr<Node>(new Node(to_insert)); ... } So I'm wrapping the function that would put the pointer into the container, vector::push_back, and relying on the by-value auto_ptr argument to ensure that the Node* is deleted if the vector resize fails. Is this an idiomatic use of auto_ptr to save a bit of boilerplate in my Tree::insert? Any improvements you can suggest? Otherwise I'd have to have something like: Node* n = ...; // find where to insert the new node auto_ptr<Node> new_node(new Node(to_insert)); n->m_children.push_back(new_node.get()); new_node.release(); which kind of clutters up what would have been a single line of code if I wasn't worrying about exception safety and a memory leak. (Actually I was wondering if I could post my whole code sample (about 300 lines) and ask people to critique it for idiomatic C++ usage in general, but I'm not sure whether that kind of question is appropriate on stackoverflow.)

  Read the article

• CSS: my side bar overflow the container div's border when I set it's height to 100%

  - by mnml

  Hi, My side bar overflow the container div's border when I set it's height to 100%, I would like to know if there is any way I can have it's height 100% minus some px. Here is the source: <div id="main"> <br /><br /> <div class="content"> <div id="sidecontent"> <h1 id="title">Title</h1> ***** </div> <div id="sidebar"> <div class="sidebox"> **** </div> </div> </div> <div class="bottom"></div> </div> #main { position: relative; background:transparent url('/public/images/main_bg.png') top left repeat-y; padding:37px 37px 37px 37px; margin-left: auto ; margin-right: auto ; width:940px; min-height: 363px; } #main div.top, #main div.bottom { height:70px; width:1015px; position: absolute; left:0px; } #main div.content { padding:0 15px 0 15px; } #sidecontent { width: 675px; } #sidebar { background: #fff url('/public/images/bg_side.png') top right repeat-y; position: absolute; height: 100%; right:34px; top:42px; width: 200px; padding: 10px 10px 0px 40px; z-index:50; } .created_at { color:gray; } .sidebox { margin-bottom: 5px; } #main div.top { top:-70px; background: transparent url(/public/images/main_top.png) bottom no-repeat; } #main div.bottom { bottom:-70px; background: transparent url(/public/images/main_bottom.png) top no-repeat; }

  Read the article

• do-while loop in Python?

  - by Eye of Hell

  I need to emulate a do-while loop in a python. But, unfortunately, following straightforward code does not work: l = [ 1, 2, 3 ] i = l.__iter__() s = None while True : if s : print s try : s = i.next() except StopIteration : break print "done" Instead of "1,2,3,done" I have the following output: [stdout:]1 [stdout:]2 [stdout:]3 None['Traceback (most recent call last): ', ' File "test_python.py", line 8, in <module> s = i.next() ', 'StopIteration '] What can I do in order to catch 'stop iteration' excepton and break a while loop properly? Example why such thing may be needed. State machine: s = "" while True : if state is STATE_CODE : if "//" in s : tokens.add( TOKEN_COMMENT, s.split( "//" )[1] ) state = STATE_COMMENT else : tokens.add( TOKEN_CODE, s ) if state is STATE_COMMENT : if "//" in s : tokens.append( TOKEN_COMMENT, s.split( "//" )[1] ) else state = STATE_CODE # re-evaluate same line continue try : s = i.next() except StopIteration : break

  Read the article

• PDO::fetchAll vs. PDO::fetch in a loop

  - by Byron

  Just a quick question. Is there any performance difference between using PDO::fetchAll() and PDO::fetch() in a loop (for large result sets)? I'm fetching into objects of a user-defined class, if that makes any difference. My initial uneducated assumption was that fetchAll might be faster because PDO can perform multiple operations in one statement while mysql_query can only execute one. However I have little knowledge of PDO's inner workings and the documentation doesn't say anything about this, and whether or not fetchAll() is simply a PHP-side loop dumped into an array. Any help?

  Read the article

• AJAX call in for loop won't return values to correct array positions

  - by Heilemann

  I need to get a range of pages using AJAX and put them into an array, where their given place in the array is equal to the i of a for loop (it's a caching-like function for blog pages, and the range of the for loop is entirely variable). I'm doing something akin to the following: var bongo = new Array(); for (i = 0; i < 10; i++) { jQuery.ajax({ type: "GET", url: http://localhost, data: queryString, success: function(request) { bongo[i] = request } }) } The problem is, that unless I add async: false to the .ajax options (which would make it... SJAX?), which causes the requests to basically pause the browser, going against what I'm trying to do, the i in the success callback will always end up being 11, whereas I of course want it to pour the returned data into each slot of the array from 0 to 10. I've tried replacing the line with this: bongo[i] = jQuery.ajax({ type: "GET", url: http://localhost, data: queryString }).responseText But that made no difference.

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >