Search Results

Search found 1360 results on 55 pages for 'is it plugged in'.

Page 47/55 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

  • WAN Optimization for Small Office/Home Office

    - by TiernanO
    I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

    Read the article

  • PCI Tv Tuner not receiving signal

    - by C-dizzle
    I inherited an Angel II PCI Dual TV Tuner card, popped it into my computer's PCI slot, plugged in my coax cable, but am having trouble getting any type of signal to it. The computer I am using is Windows 7 Ultimate 32 bit, I know the card works because the computer recognizes it and installs the drivers, or at least I assume it works because of that. I'm trying to use Windows Media Center to watch/record tv. Here are a few things I have tried to get it working: Uninstalled/Reinstalled the newest drivers Tried hooking up an antenna to the coax input instead of my cable Instead of using cable splitter, went directly from wall output into card with coax cable Tried using different output on splitter in case the out port was bad I haven't tried a different coax cable yet, it should be fine since it's pretty new. Since this is my first time setting up a TV Tuner card, is there anything specific that I need to do with it? Is there any configuration that needs to be done on it? Do I need to have a digial receiver? I was getting pretty frustrated with it so I wanted to turn here to the experts, I'm sure someone can help me figure it out.

    Read the article

  • Dosbox USB print Windows 8.1 64Bit

    - by eCronik
    Worked fine until I've upgraded to Windows 8.1 as well as made the mail programm working (had to get a windows live ID and have to type in a password now, when starting Windows). I did set the USB printer to lpt1 on the local Windows 8 computer and another XP computer via LAN to lpt2 the same way with the same printer on the Windows 8 computer. But now it doesn't work anymore from the Win8 one (where the printer is plugged via USB). Tried already deleting lpt2: on the XP one, as well as lpt1 on the Windows 8, resetted it. Not working... :-( I tried also net use lpt1: \server\printer password "\user:Ute Berger" /persistent:yes of course with the correct server and shared printer name as well as net use \server\printer "\user:Ute Berger" password /persistent:yes . This is the name displayed as a user now. But in C:\users it is named Benutzer1. Tried this one also. Nothing worked. What could be the problem here? What's strange is that when I type "net use lpt1:" on the XP, I get another error (67 - The networkname wasn't found) than trying something I didn't set up like lpt2 (2 - The system can't find the file). Could this be a possible problem as even if deleted something is left blocking on the Windows 8 computer? Please help me - I tried for hours today but all I've got was frustration... Regards Tim

    Read the article

  • Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

    - by Gabble
    I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

    Read the article

  • Why Would one VLAN have no Communication on one Switch?

    - by Webs
    So the problem is we have a device or host that needs to communicate on a specific VLAN. This VLAN is not new, it is running all throughout our environment and works fine. But the VLAN was recently configured on the switch in question, a Cisco 3750. The DHCP server is handing out addresses on that VLAN with no problem. I have verified the cable between the host and switch and tried multiple hosts, but none of them can communicate or get an address. I plugged my laptop into an empty port which had a different VLAN assigned and immediately got a DHCP address. When I changed that port to the same VLAN I'm having issues with I got the same problem. The laptop just sits there and tries to DHCP an address but nothing happens. I double checked the cores and their Layer 3 VLAN config and its fine too. Plus I figured the issue couldn't be with them because the VLAN works fine everywhere else it exists. So the only other thing I can think of is the switch, but the VLAN exists on the switch and seems to be configured correctly. The trunks appear to be configured just fine as well too. Anyone have any ideas? I'm lost on this one.

    Read the article

  • How long will a "safely stored" Solid-State-Drive (SSD) keep its data? (e.g. bank safety-deposit box)

    - by user31575
    Here's my usecase: once-and-only-once copy off photos/videos to an internal SATA Solid State Drive (SSD) put this drive in a well-ventilated, air-conditioned bank "safety deposit box" for safe keeping The question: How long can I safely store a solid-state-drive in such an environment? i.e. 0% bitrot, 100% success when "plugged in" Are some SSD drives more reliable than other for this usecase? (e.g. smaller size vs larger size, SLC vs MLC, different brands, etc) More fodder: I have read that solid state memory cards (e..g compactflash, or sd cards) have much longer durability than other media (DVD's, CD's, hard drives) for this usecase (guaranteed against bitrot/other dysfunction on the order of ~ a decades vs a year ). I don't know if this applies to "SSD hard drives". Copying to one 500Gb ssd vs 8 64gb flash drives is easier SSD SATA hard drives have no moving parts, but they have more "visible electronics" than a compact flash card. I don't know if this "visible electronics" can fail, i.e. in contr I know many will point to carbonite, other cloud backup stuff, but I like the simplicity of having physical copies and wanted to understand the risks/implications thanks,

    Read the article

  • Computer keeps restarting [closed]

    - by Joris
    I have a strange problem with my desktop pc, when I start it, it just restarts immediately, it displays the bios/motherboard logo and then restarts. I can't access the bios to edit settings because it restarts to fast. Then I tried different things to fix it with mixed success. (I also tried to reset the bios without success) I noticed that a capacity from the graphics card was broken (it looked exploded) so I ordered a new graphics card & plugged it in the computer. It didn't change much, still the same problem. Then I unplugged everything that's not necessary and put only 1Gig RAM in the motherboard (usually it has 4 x 1Gig RAM) and the computer started, then I putted another gig of RAM and the computer still started. (starting=booting windows) When I putted in the 3th RAM it didn't boot anymore (again restarting all the time) so I removed this 3th gig of RAM and this is where it gets weird. I expected the computer to boot again because it is exactly the same configuration as before - which worked - but the computer didn't want to start. It just gave the same problem as before (restarting all the time.. ) Anyone an idea what might be wrong?

    Read the article

  • Connecting a Wifi router to receivers with a cable instead of antenna?

    - by 31eee384
    This is a very strange question--I'd go so far as to say it's a stupid question. I'm being told that it is possible to, to describe it briefly, use a cable to connect an access point and a receiver directly to one another. This means that I would unscrew the access point's antenna, and attach one end of a cable to the port. Then, on the wireless receiver, I would also unscrew the antenna and plug in the other side of the cable. I'm being told the connection would work after this, just as a normal Wifi connection would. Bonus mini-question: if this works, would it still work if a splitter were attached to the access point and multiple receivers plugged in to the network? What would happen if I do this? Based on my surprisingly deficient knowledge of radio transmission, I don't think it would work. I would like some help knowing why it won't (or will) though, if possible. This is a somewhat hypothetical question--I realize that Ethernet does this exact job very handily, and I could just throw in a switch instead of the splitter. I simply feel that I should understand this scenario. Thanks for any help you can offer.

    Read the article

  • my cpu won't start. all fan were spinning for a second then nothing happen

    - by Tommy
    I need help about this.. I'm from Malaysia.. Back then my cpu is all okay..and it's 4 year old.. I think this question is answered before but i'm still don't understand.. when i plugged my cpu..turn it on and all of the fan (graphic card, mobo fan and PSU fan) were spinning just for a second than nothing happen.. I don't know if it is because of the PSU or my mobo.. I sent my cpu to the shop and they said it must be the mobo.. They tell me to change my mobo and PSU also..and it cost over 100 buck (rm300 in Malaysia). and i'm real 'dry' right now. My whole data is inside the HDD. School projects, photos, games, and many..I really-really need my cpu back alive.. My mobo is MSI MS-7529 with dual core chips. My PSU is ATX-480W. the PC store guy said i need to change to new ASUS mobo if I want. I dont know what type it is but Then he tell me to change my PSU also because he don't think my old PSU (ATX-480W) ain't compatible to the new mobo.. I was very need a help from you techie guys.. sorry for my terrible English..

    Read the article

  • Ubuntu 10.10 - disaster - what other linux for beginner?

    - by A-ha
    Guys, I've tried to install ubuntu (desktop and notebook ed) on my laptop and unortunately I have to say that as despite the fact that installation process supposed to be easy I couldn't finish installation of this system - didn't detect my keyboard or rather lost my keyboard as soon as I tried to switch on/off pad on my laptop. After I've discovered that, I started all over again (this time without touching my laptop's pad during installation) and yes, eventually it get to the end of installation. Unfortunately, when I've tried to switch my pad (sometimes I just do not want to use a mouse) the whole system froze. So I had to restart it with the power button and this time I didn't touch pad at all, plugged in mouse and tried to rearrange taskbars according to my liking (all taskbars on the top side of the screen and auto-hide on) and I gave up. It is so unfinished that I just can't be bothered to use it. I would like to have one linux system on my machine so I started googling and most of the links are to either ubuntu (which I just do not want to touch for now) and suse or commercial versions of linux. I do not really mind paying for something (and having experience with ubuntu I'd rather pay and have something pro then get it free and discover that it's unusable). So could someone please provide short list of linux distros which would be appropriate for a beginner, and I don't mind paying for it, I just want it to be a professional product.

    Read the article

  • Windows 7 - Can't get my TV working as primary display with nVidia 7900GS

    - by Daniel Schaffer
    I just installed Windows 7 Ultimate 64 RTM (from MSDN) on my HTPC, which is connected to a 42" Magnavox LCD TV via component cables to my nVidia 7900GS. Everything was fine through the installation until I went to install the official driver from nVidia. Towards the end of the installation, the TV blinked off and wouldn't come back on. I went and got an LCD monitor and plugged it into a DVI port and the monitor came right up, but was automatically selected as the primary display. Now, if I set the TV to be the primary display, the TV just blanks until I hit escape to cancel the "settings have changed, do you want to keep them" dialog. Any suggestions? Update: I'm able to set the TV as the primary display using the Windows 7 "screen resolution" configuration panel. However, if I try to remove the LCD monitor either by unplugging it or using the configuration, the TV blanks out again. Update 2: This setup was working correctly in Vista Home Premium 32-bit. Update 3: I've uninstalled the nVidia driver and am using the driver that Windows Update installed. As much as this offends my geek sensibilities (must use the "right" driver!!), well, It Works™.

    Read the article

  • Un-do Windows disk convert HFS+

    - by BLAKE
    Last night, a friend asked my to give him a copy of a word document. He handed me an external hard drive and left. I plugged the hard drive into my file server running Windows Server 2003, opened disk management and clicked OK. (I know that in Windows 2003 you need to manually assign a drive letter to external drives.) I then looked at the drive in disk management and it said that it was unallocated space. I called my friend and he said that there was data on the drive, but he used it with his Mac Book. Aperantly when I clicked OK in disk management I converted the from HFS+ file system to something else. Is there any way to undo the disk convert? I immediately removed the drive, so there was no writing to it. Windows did not format the drive, it just converted it. Is the data still there? All the data recovery programs I have are for windows, can they read the Mac file system? I need to get the data back, what can I do?

    Read the article

  • computer fails to boot during/after POST for five or six boots, then works

    - by N13
    For the last few days, my computer has had issues booting. I've seen two different behaviors: The screen displays the graphics card information, then begins to list the RAM, hard drives, etc. At different points in this process (after the graphics info), the computer shuts off. After five or six attempts, it then boots normally. In roughly the same time frame, the computer freezes, and fails to boot. I think it boots successfully on the next attempt. I've also noticed that in some instances, the computer freezes on shutdown. It gets right to the point where it should shut off, but doesn't. I recently combined the best parts of two different machines into this one. I'm booting to GRUB, with Ubuntu 12.04, Linux Mint 11 and Windows Vista (unfortunately) as my OS options. It has an Enermax Modu82+ 525W power supply, and I've used an online calculator to determine that my load shouldn't exceed 400W. I even unplugged a hard drive, but that didn't help. I found the latest BIOS, patched it and checked the settings, but that didn't fix it. I'm fairly certain this issue didn't exist at first, but might have started when the power at my new apartment dropped for a second. The machine is plugged into a surge protector strip, but it's old and I've heard they lose effectiveness with age. Is a power dip as damaging as a spike? If something were damaged, why would it boot successfully after five or six attempts? It's almost like the BIOS or PSU need to be primed. The trouble with debugging is that there seems to be a "grace period" after shutdown where the issue doesn't present itself again. What should I try next?

    Read the article

  • Western Digital My Book not recognized by WD software

    - by Kari
    A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

    Read the article

  • No sound out of headphone port

    - by Thanatos
    I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

    Read the article

  • Using Truecrypt to secure mySQL database, any pitfalls?

    - by Saul
    The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

    Read the article

  • How to disable monitor auto detection in Windows 7?

    - by Jay Yother
    I am currently running Windows 7 Ultimate 64-bit with a dual monitor setup with an NVIDIA 7950 GT graphics card. One monitor is dedicated to this machine and the other monitor is connected to a DVI KVM switch. When I switch to my other computer, Windows 7 disables the monitor. However, when I switch back it does not re-enable the monitor. The only circumstance that automatically re-enables the second monitor is when I switch back after Windows has put the monitors into power save mode. I am continually having to bring up the NVIDIA control panel to have it re-enable the monitor. Under Windows XP I would just disable the NVIDIA service to prevent it from auto-detecting the monitor (which doesn't solve the problem under Win7), and in Vista there was a registry hack that would prevent this. It looks as though that has been removed in Windows 7. I have found similar questions posted on this site, but nothing that matches my problem exactly. The following link is the question that comes the closest, but does not provide a solution to the problem. http://superuser.com/questions/96683/how-to-fix-monitor-detection-on-windows-7 Is there a way in Windows 7 to disable monitor auto-detection? Update: I just added a second graphics card to my Windows 7 64-bit machine. I plugged one monitor into each graphics card. Now, when I use the KVM switch to switch back and forth it will re-enable the second monitor like it should. There are however, a few quirks with this. If I have a program maximized on the second monitor and it has focus, when I switch it will move to monitor 1. If I have a program maximized on the second monitor and it does not have focus, when I switch it will behave like it is minimized and when I bring it back up it will show up maximized on monitor 1. Definitely better than it was, but still looking for a way to disable the auto-detection.

    Read the article

  • Can not mount my USB disk-- Ubuntu nor windows[dmesg including]

    - by EthanZ6174
    first, here is my dmesn|tail result right after i plugged the disk: $ dmesg | tail [ 2578.697224] scsi 6:0:0:0: Direct-Access HP v100w PMAP PQ: 0 ANSI: 0 CCS [ 2578.698322] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 2578.916464] sd 6:0:0:0: [sdb] 3921920 512-byte logical blocks: (2.00 GB/1.87 GiB) [ 2578.916950] sd 6:0:0:0: [sdb] Write Protect is off [ 2578.916956] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00 [ 2578.916961] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922460] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.922470] sdb: [ 2578.969570] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 2578.969578] sd 6:0:0:0: [sdb] Attached SCSI removable disk there is nothing after 'sdb:' ... at the meantime, the lsusb shows: $ lsusb Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 004: ID 03f0:3207 Hewlett-Packard Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 002: ID 045e:0737 Microsoft Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub so... can anyone help me? what's wrong with my USB disk? THX

    Read the article

  • Intel Motherboard Lightning Victim Dies Hard

    - by Stetson RDT
    Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

    Read the article

  • VGA Cable gave me an Electric Shock when connecting a Projector to a Laptop

    - by Felipe Luarte
    Yesterday I was trying to connect a Viewsonic Projector to my Samsung RC420 laptop... I followed this steps: I Plugged the Projector to a power source, in parallel I did the same thing with the laptop. Then I turned on the laptop, but not the Projector (this one turns a bright light when is connected to a power source). I put the VGA Cable to the Projector (this one being still turned down) and then when I was getting close to the VGA port of the Laptop... BAM! A big spark appear between the port and the cable! Immediately the whole electricity of my floor went off. A part of the port in my laptop kind of... melted down. It seems to be where the spark started. The same thing happened to the part of the cable involved. Now I'm using the laptop, and it seems that there is no problem in it, I haven't connect anything to the VGA port yet. And the projector is still working to, well... it turns on, and I haven't connect anything yet too. The projector was connected to the power source by a homemade electric extension.

    Read the article

  • Problems with USB-Devices using VDR

    - by emmsinator
    Hey Guys, I'm using VDR on vSphere4. It works sucessfully. I've already backuped several VMs with VDR and I like it very much. But now we got a problem. We have 2 VMs, using an USB-Device Server with a stick plugged in, which is definetely need by these 2 VMs for Licensing and so. Every time, I start the Backup process, the VMs lost the communication to the USB-Server and its stick after building the snapshot and while online. Because of that, the software on these VMs can't work correctly. I have to restart both Machines to solve this problem. These fact is bad for an automatic backup. Does VDR have a special function for those cases or is something like this already known? It would be no problem, to shutdown the servers for building snapshots on Saturday or Sunday. Can VDR initiate a shutdown before starting the backup process? Otherwise I must try to use scripts, but that wouldn't be so nice. Thanks a lot for your help.

    Read the article

  • Windows XP usb drivers reinstalling upon reboot

    - by iWerner
    We have a Windows XP SP3 laptop (Acer Travelmate 7320) to which we connect a variety of astronomy equipment (a telescope, its mount, some cameras and others) all of which connect through USB. When we plug in these devices, Windows tells us that it detects the hardware and installs the driver. All of these devices then function correctly using the software that came from the vendor (unfortunately, one of the vendors does not support Vista 64, and that is why we're using our XP laptop). However when we reboot the computer we experience a variety of symptoms: Windows reports that it found new hardware for some of the devices and tries to reinstall their drivers, and for some of the other devices needs to be unplugged and plugged in again before they are detected again by the operating system, in which case Windows still tries to reinstall their drivers. It is as if Windows does not remember that it has already installed the drivers. Is this a common problem on Windows XP? If so, what can be done about it? Should we rather be looking at the laptop's firmware and drivers? We've looked into updating the drivers for the chipset, but this did not solve the problem. Thank you in advance.

    Read the article

  • INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

    - by kdgregory
    History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

    Read the article

  • RAID5 issue after replacing motherboard and upgrading firmware

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with Windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. This screenshot should show that the SNs match, which raises the question why the software doesn't realize the drive is a member of the array. I'd like to know if anyone has experienced anything similar, and what should I do, can I force the drive to be recognized as a member (without wiping data)?

    Read the article

  • What is the risk of introducing non standard image machines to a corporate environment

    - by Troy Hunt
    I’m after some feedback from those in the managed desktop or network security space on the risks of introducing machines that are not built on a standard desktop image into a large corporate environment. This particular context relates to the standard corporate image (32 bit Win XP) in a large multi-national not being suitable for a particular segment of users. In short, I’m looking at what hurdles we might come across by proposing the introduction of machines which are built and maintained by a handful of software developers and not based on the corporate desktop image (proposing 64 bit Win 7). I suspect the barriers are primarily around virus definition updates, the rollout of service packs and patches and the compatibility of existing applications with the newer OS. In terms of viruses and software updates, if machines were using common virus protection software with automated updates and using Windows Update for service packs and patches, is there still a viable risk to the corporate environment? For that matter, are large corporate environments normally vulnerable to the introduction of a machine not based on a standard image? I’m trying to get my head around how real the risk of infection and other adverse events are from machines being plugged into the network. There are multiple scenarios outside of just the example above where this might happen (i.e. a vendor plugging in a machine for internet access during a presentation). Would a large corporate network normally be sufficiently hardened against such innocuous activity? I appreciate the theory as to why policies such as standard desktop images exist, I’m just interested in the actual, practical risk and how much a network should be protected by means other than what is managed on individual PCs.

    Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >