Search Results

Search found 5472 results on 219 pages for 'j4c3n 14'.

Page 47/219 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• Nginx + Nagios : 502 Bad gateway

  - by MrROY

  I have a fully new install nagios, but I can't access to it. Here's my Nginx config: server{ listen 80; server_name 61.148.45.10; # blahblah # Nagios Monitoring location /nagios3/ { proxy_pass http://127.0.0.1:80; } } Nagios is installed step by step(From this Linode guide): sudo apt-get install -y nagios3 Then I try to visit http://ip-address/nagios3/, but it shows 502 bad gateway. How do I deal with this ? This is my /var/log/syslog: Oct 25 14:18:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;1;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:19:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;1;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:19:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;2;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:20:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;2;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:20:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;3;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;3;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:21:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;HARD;4;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server nagios3: SERVICE NOTIFICATION: root;localhost;Disk Space;WARNING;notify-service-by-email;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server postfix/pickup[24474]: 4F89F394034C: uid=109 from=<nagios> Oct 25 14:21:17 my-server postfix/cleanup[27756]: 4F89F394034C: message-id=<20131025062117.4F89F394034C@my-server> Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: from=<nagios@[email protected]>, size=594, nrcpt=1 (queue active) Oct 25 14:21:17 my-server postfix/local[27758]: 4F89F394034C: to=<root@localhost>, relay=local, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: removed Oct 25 14:22:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;HARD;4;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server nagios3: SERVICE NOTIFICATION: root;localhost;HTTP;WARNING;notify-service-by-email;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server postfix/pickup[24474]: 219CA3940381: uid=109 from=<nagios> Oct 25 14:22:07 my-server postfix/cleanup[27756]: 219CA3940381: message-id=<20131025062207.219CA3940381@my-server> Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: from=<nagios@[email protected]>, size=605, nrcpt=1 (queue active) Oct 25 14:22:07 my-server postfix/local[27758]: 219CA3940381: to=<root@localhost>, relay=local, delay=0.12, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: removed Oct 25 14:39:01 my-server CRON[28242]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) And there're lot of 127.0.0.1 visit in nginx log, but I actually visit from a external ip: 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36"

  Read the article

• Ubuntu 12.04 KVM running Ubuntu 12.04 with linux-image-virtual crash on boot

  - by D.Mill

  One of my VMs is stuck on "pause" in virsh. If I destroy and restart it, it will go to pause after a bit of time as "running". I can at best enter my username at login if I'm quick but it'll then shutdown. I don't know where to start with this so any help would be great!! I can access the VMs files via guestfish. the kern.log and syslog don't populate new lines. This is the last input I get from kern.log: Dec 13 11:21:08 soft201 kernel: imklog 5.8.6, log source = /proc/kmsg started. Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpuset Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpu Dec 13 11:21:08 soft201 kernel: [ 0.000000] Linux version 3.2.0-34-virtual (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #53-Ubuntu SMP Thu Nov 15 11:08:40 UTC 2012 (Ubuntu 3.2.0-34.53-virtual 3.2.33) Dec 13 11:21:08 soft201 kernel: [ 0.000000] Command line: root=UUID=61d48b48-a06a-48fb-842e-b38014086a93 ro quiet splash Dec 13 11:21:08 soft201 kernel: [ 0.000000] KERNEL supported cpus: Dec 13 11:21:08 soft201 kernel: [ 0.000000] Intel GenuineIntel Dec 13 11:21:08 soft201 kernel: [ 0.000000] AMD AuthenticAMD Dec 13 11:21:08 soft201 kernel: [ 0.000000] Centaur CentaurHauls Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-provided physical RAM map: Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfffc000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000dfffc000 - 00000000e0000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000feffc000 - 00000000ff000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000a20000000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] NX (Execute Disable) protection: active Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI 2.4 present. Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2007 Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) Dec 13 As you can see the last line gets cut off. I don't even know if this is that relevant. dmesg logs are empty. The qemu log for the VM returns this: 2012-12-13 12:29:47.584+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 40960 -smp 14,sockets=14,cores=1,threads=1 -name numerink201 -uuid f4a889ed-a089-05d0-cc9d-9825ab1faeba -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/numerink201.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/client.soft.fr/tmpcZAD9U.qcow2,if=none,id=drive-ide0-0-0,format=qcow2 -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -fsdev local,security_model=none,id=fsdev-fs0,path=/home/shared_folders/soft201 -device virtio-9p-pci,id=fs0,fsdev=fsdev-fs0,mount_tag=hostshare,bus=pci.0,addr=0x5 -netdev tap,fd=18,id=hostnet0 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=02:00:00:1d:b9:e7,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:0 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/3 qemu: terminating on signal 15 from pid 28248 2012-12-13 12:30:14.455+0000: shutting down I've added more logging, libvirt.log gives me this: 2012-12-13 13:24:38.525+0000: 27694: info : libvirt version: 0.9.8 2012-12-13 13:24:38.525+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:38.525+0000: 27694: warning : qemuCapsInit:856 : Failed to get host power management capabilities 2012-12-13 13:24:39.865+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.865+0000: 27694: warning : lxcCapsInit:77 : Failed to get host power management capabilities 2012-12-13 13:24:39.866+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.866+0000: 27694: warning : umlCapsInit:87 : Failed to get host power management capabilities I don't really know where to go from here. I'll post whatever info you require

  Read the article

• Troubleshooting unwanted NTP Traffic

  - by Jaxaeon

  A domain controller running Windows Server 2012 is sending NTP and NETBIOS traffic to an address that has never been configured as a time provider. The server logs give no indication that any NTP traffic is failing. The only place I see any evidence of this traffic is in pfSense system logs: (Blocked) Jun 9 08:48:50 DOMAIN 10.0.1.100:123 192.128.127.254:123 UDP (Blocked) Jun 9 08:48:53 DOMAIN 10.0.1.100:137 192.128.127.254:137 UDP As far as I can tell the NTP service is working normally otherwise: DC2.domain.com[10.0.1.101:123]: ICMP: 0ms delay NTP: -0.0131705s offset from DC1.domain.com RefID: DC1.domain.com [10.0.1.100] Stratum: 3 DC1.domain.com *** PDC ***[10.0.1.100:123]: ICMP: 0ms delay NTP: +0.0000000s offset from DC1.domain.com RefID: clock1.albyny.inoc.net [64.246.132.14] Stratum: 2 The time provider NtpClient is currently receiving valid time data from 1.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->204.2.134.163:123). The time provider NtpClient is currently receiving valid time data from 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). The time service is now synchronizing the system time with the time source 0.pool.ntp.org,0×1 (ntp.m|0x0|0.0.0.0:123->64.246.132.14:123). I've been inside and out of the NTP configuration and cannot find any reason for this traffic. Reverse DNS points the destination address to nothing.attdns.com. pinging nothing.attdns.com from the domain controller in question leads to a response from loopback (127.0.0.2) which makes my head hurt. Any ideas? EDIT1: It should probably be noted that after a dns flush, nslookup 192.128.127.254 returns nothing.attdns.com. 192.128.127.254 is not present in domain.com DNS records. The attdns.com domain is not present in cached lookups. 127.in-addr.arpa is clean of any funkyness. EDIT2: The loopback ping response from nothing.attdns.com is possibly unrelated. Machines on other networks are also displaying this behavior. EDIT3: As mentioned in the comments, I tracked the problem network adapter back to my pfSense VM hosted in esxi 5.5 (I know shame on me for virtualizing a firewall). pfSense was configured to use DC1.domain.com as its primary time provider, but upon changing it back to pool.ntp.org the problem persists. pfSense logs give no indication of NTP misconfiguration. Everywhere I can think to look this VM is identified as 10.0.1.253, so I still have no idea why it’s sending NTP requests as 192.128… Since this firewall was a temporary solution to a problem that no longer exists so I am going to decommission it. EDIT4: The queries were coming from another machine sharing the same virtual adapter as the firewall. The machine has two local adapters: one for LAN, and the other for attached hardware that uses an Ethernet connection. That hardware sits in the the mystery subnet, and the machine is broadcasting NTP requests over both adapters.

  Read the article

• openvpn not creating internal route for client

  - by user42055

  I have two openvpn clients and a server using shared keys. I have internal routes specified in the ccd directory for both clients, but when they connect, the server only creates the internal route for one of them, despite the logs saying it's creating both. Both clients and the server use the "--script-security 2" command-line option. Can anyone think of why it would do this ? My ccd files are: client1: iroute 192.168.0.0 255.255.255.0 client2: iroute 10.0.1.0 255.255.255.0 My log file shows the following (cropped): May 3 17:22:59 kino openvpn[2416]: 118.208.58.60:48730 [client1] Peer Connection Initiated with 118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 OPTIONS IMPORT: reading client specific options from: ccd/client1 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.150.10 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: primary virtual IP for client1/118.208.58.60:48730: 192.168.150.10 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: internal route 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:22:59 kino openvpn[2416]: client1/118.208.58.60:48730 MULTI: Learn: 192.168.0.0/24 -> client1/118.208.58.60:48730 May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:23:01 kino openvpn[2416]: client1/118.208.58.60:48730 SENT CONTROL [client1]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.10 192.168.150.9' (status=1) May 3 17:21:36 kino openvpn[2416]: 124.148.1.90:59277 [client2] Peer Connection Initiated with 124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 OPTIONS IMPORT: reading client specific options from: ccd/client2 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 192.168.150.14 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: primary virtual IP for client2/124.148.1.90:59277: 192.168.150.14 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: internal route 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:36 kino openvpn[2416]: client2/124.148.1.90:59277 MULTI: Learn: 10.0.1.0/24 -> client2/124.148.1.90:59277 May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 PUSH: Received control message: 'PUSH_REQUEST' May 3 17:21:39 kino openvpn[2416]: client2/124.148.1.90:59277 SENT CONTROL [client2]: 'PUSH_REPLY,route 192.168.150.1,topology net30,ping 10,ping-restart 120,ifconfig 192.168.150.14 192.168.150.13' (status=1) And after both clients have connected, the routing table looks like this: 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 203.209.167.192 0.0.0.0 255.255.255.224 U 0 0 0 eth0 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 203.209.167.193 0.0.0.0 UG 0 0 0 eth0 As you can see, it's created the route to 192.168.0.0/24 (client1) but not to 10.0.1.0/24 (client2), even though the log says it's been created. Any suggestions why ?

  Read the article

• Possible to give one connection to each IP?

  - by Alice

  I am having overloading problems. Too many connections, and some IP has more than 20 connection at once. I do this command. netstat -anp |grep 'tcp\|udp' | awk '{print $5}' | cut -d: -f1 | sort | uniq -c | sort -n To get total of connection and this is the output: 1 106.3.98.81 1 106.3.98.82 1 108.171.251.2 1 110.85.103.207 1 111.161.30.217 1 113.53.103.55 1 119.235.237.20 1 124.106.19.34 1 157.55.32.166 1 157.55.33.49 1 157.55.34.28 1 175.141.103.239 1 180.76.5.59 1 180.76.5.61 1 188.235.165.216 1 205.213.195.70 1 216.157.222.25 1 218.93.205.100 1 222.77.209.105 1 27.153.148.109 1 27.159.194.242 1 27.159.253.71 1 54.242.122.201 1 61.172.50.99 1 65.55.24.239 1 71.179.78.5 1 74.125.136.27 1 74.125.182.30 1 74.125.182.36 1 79.112.225.39 1 93.190.139.208 2 124.227.191.67 2 157.55.33.84 2 157.55.35.34 2 190.66.3.107 2 203.87.153.38 2 220.161.119.3 2 221.6.15.156 2 27.153.148.116 2 27.159.197.0 2 96.47.224.42 3 202.14.70.1 3 218.6.15.42 3 222.77.218.226 3 222.77.224.187 3 37.59.66.100 3 46.4.181.244 3 87.98.254.192 3 91.207.8.62 4 188.143.233.222 4 218.108.168.166 4 221.12.154.18 4 93.182.157.8 4 94.142.128.183 5 180.246.170.187 5 8.21.6.226 6 178.137.94.87 6 218.93.205.112 7 199.15.234.222 9 9 125.253.97.6 10 178.137.17.196 11 46.118.192.179 12 212.79.14.14 21 72.201.187.135 27 0.0.0.0 Can anyone give me some directions, my server crashed few times this week because of this. Thanks. EDIT: Alright, my error logs says: [Thu Oct 18 12:17:39 2012] [error] could not make child process 4842 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4843 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4855 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4856 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4861 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4869 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4872 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4873 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4874 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4875 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4876 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4880 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4882 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4885 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4897 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4900 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4901 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4906 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4907 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4925 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4926 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4927 exit, attempting to continue anyway [Thu Oct 18 12:17:39 2012] [error] could not make child process 4931 exit, attempting to continue anyway [Thu Oct 18 12:17:40 2012] [notice] caught SIGTERM, shutting down PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20060613+lfs/curl.iso' - /usr/lib/php5/20060613+lfs/curl.iso: cannot open shared object file: No such file or directory in Unknown on line 0 [Thu Oct 18 12:17:45 2012] [notice] Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny10 with Suhosin-Patch configured -- resuming normal operations And I have over thousands of line saying:(each has different process id) [Thu Oct 18 12:17:38 2012] [error] child process 4906 still did not exit, sending a SIGKILL And I also have line saying: [Wed Oct 17 09:44:58 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 50 MaxClients 300 MaxRequestsPerChild 5000 </IfModule>

  Read the article

• Mongodb Slave replication lag

  - by Leonid Bugaev

  We using standard mongo setup: 2 replicas + 1 arbiter. Both replica servers use same AWS m1.medium with RAID10 EBS. We experiencing constantly growing replication lag on secondary replica. I tried to do full-resync, you can see it on graph, but it helped only for some hours. Our mongo usage is really low now, and frankly i can't understan why it can be. iostat 1 for secondary: avg-cpu: %user %nice %system %iowait %steal %idle 80.39 0.00 2.94 0.00 16.67 0.00 Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn xvdap1 0.00 0.00 0.00 0 0 xvdb 0.00 0.00 0.00 0 0 xvdfp4 12.75 0.00 189.22 0 193 xvdfp3 12.75 0.00 189.22 0 193 xvdfp2 7.84 0.00 40.20 0 41 xvdfp1 7.84 0.00 40.20 0 41 md127 19.61 0.00 219.61 0 224 mongostat for secondary (why 100% locks? i guess its the problem): insert query update delete getmore command flushes mapped vsize res faults locked % idx miss % qr|qw ar|aw netIn netOut conn set repl time *10 *0 *16 *0 0 2|4 0 30.9g 62.4g 1.65g 0 107 0 0|0 0|0 198b 1k 16 replset-01 SEC 06:55:37 *4 *0 *8 *0 0 12|0 0 30.9g 62.4g 1.65g 0 91.7 0 0|0 0|0 837b 5k 16 replset-01 SEC 06:55:38 *4 *0 *7 *0 0 3|0 0 30.9g 62.4g 1.64g 0 110 0 0|0 0|0 342b 1k 16 replset-01 SEC 06:55:39 *4 *0 *8 *0 0 1|0 0 30.9g 62.4g 1.64g 0 82.9 0 0|0 0|0 62b 1k 16 replset-01 SEC 06:55:40 *3 *0 *7 *0 0 5|0 0 30.9g 62.4g 1.6g 0 75.2 0 0|0 0|0 466b 2k 16 replset-01 SEC 06:55:41 *4 *0 *7 *0 0 1|0 0 30.9g 62.4g 1.64g 0 138 0 0|0 0|1 62b 1k 16 replset-01 SEC 06:55:42 *7 *0 *15 *0 0 3|0 0 30.9g 62.4g 1.64g 0 95.4 0 0|0 0|0 342b 1k 16 replset-01 SEC 06:55:43 *7 *0 *14 *0 0 1|0 0 30.9g 62.4g 1.64g 0 98 0 0|0 0|0 62b 1k 16 replset-01 SEC 06:55:44 *8 *0 *17 *0 0 3|0 0 30.9g 62.4g 1.64g 0 96.3 0 0|0 0|0 342b 1k 16 replset-01 SEC 06:55:45 *7 *0 *14 *0 0 3|0 0 30.9g 62.4g 1.64g 0 96.1 0 0|0 0|0 186b 2k 16 replset-01 SEC 06:55:46 mongostat for primary insert query update delete getmore command flushes mapped vsize res faults locked % idx miss % qr|qw ar|aw netIn netOut conn set repl time 12 30 20 0 0 3 0 30.9g 62.6g 641m 0 0.9 0 0|0 0|0 212k 619k 48 replset-01 M 06:56:41 5 17 10 0 0 2 0 30.9g 62.6g 641m 0 0.5 0 0|0 0|0 159k 429k 48 replset-01 M 06:56:42 9 22 16 0 0 3 0 30.9g 62.6g 642m 0 0.7 0 0|0 0|0 158k 276k 48 replset-01 M 06:56:43 6 18 12 0 0 2 0 30.9g 62.6g 640m 0 0.7 0 0|0 0|0 93k 231k 48 replset-01 M 06:56:44 6 12 8 0 0 3 0 30.9g 62.6g 640m 0 0.3 0 0|0 0|0 80k 125k 48 replset-01 M 06:56:45 8 21 14 0 0 9 0 30.9g 62.6g 641m 0 0.6 0 0|0 0|0 118k 419k 48 replset-01 M 06:56:46 10 34 20 0 0 6 0 30.9g 62.6g 640m 0 1.3 0 0|0 0|0 164k 527k 48 replset-01 M 06:56:47 6 21 13 0 0 2 0 30.9g 62.6g 641m 0 0.7 0 0|0 0|0 111k 477k 48 replset-01 M 06:56:48 8 21 15 0 0 2 0 30.9g 62.6g 641m 0 0.7 0 0|0 0|0 204k 336k 48 replset-01 M 06:56:49 4 12 8 0 0 8 0 30.9g 62.6g 641m 0 0.5 0 0|0 0|0 156k 530k 48 replset-01 M 06:56:50 Mongo version: 2.0.6

  Read the article

• Cannot connect to website - SSL handshaking fails

  - by ravenspoint

  So I cannot connect to certain websites. Just a few, most are OK. The one I really care about is paypal.com. I have done the usual things. Let's see: Checked my etc/hosts Flushed the DNS cache Checked firewall Switched on & off virus protection Switched on and off ad blocking pinged the sites Eventually, I decided to look at what curl is saying in detail == Info: About to connect() to www.paypal.com port 443 (#0) == Info: Trying 66.211.169.2... == Info: connected == Info: SSLv3, TLS handshake, Client hello (1): => Send SSL data, 110 bytes (0x6e) 0000: 01 00 00 6a 03 01 4f 6c aa 8c 57 2b 3d 1e 74 64 ...j..Ol..W+=.td 0010: c1 27 25 a5 3a 12 7f 3f 41 0a 17 15 2e c9 67 7c .'%.:.?A.....g| 0020: b3 e1 f6 9a db a9 00 00 2a 00 39 00 38 00 35 00 ........*.9.8.5. 0030: 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 ......3.2./..... 0040: 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 ................ 0050: 03 00 ff 01 00 00 17 00 00 00 13 00 11 00 00 0e ................ 0060: 77 77 77 2e 70 61 79 70 61 6c 2e 63 6f 6d www.paypal.com (hangs here for ever) This looks to me like paypal is refusing to reply to the first SSL handshake. I don't know much about SSL, but compaing to the output from a site that works for me seems to make it obvious == Info: About to connect() to www.cibc.com port 443 (#0) == Info: Trying 159.231.80.200... == Info: connected == Info: SSLv3, TLS handshake, Client hello (1): => Send SSL data, 108 bytes (0x6c) 0000: 01 00 00 68 03 01 4f 6c ad 6a 1f 67 d5 84 c4 4b ...h..Ol.j.g...K 0010: 0d 49 ae d6 b9 5b c3 63 f9 48 aa 18 da 43 d1 32 .I...[.c.H...C.2 0020: 47 ae 17 e5 cd e9 00 00 2a 00 39 00 38 00 35 00 G.......*.9.8.5. 0030: 16 00 13 00 0a 00 33 00 32 00 2f 00 07 00 05 00 ......3.2./..... 0040: 04 00 15 00 12 00 09 00 14 00 11 00 08 00 06 00 ................ 0050: 03 00 ff 01 00 00 15 00 00 00 11 00 0f 00 00 0c ................ 0060: 77 77 77 2e 63 69 62 63 2e 63 6f 6d www.cibc.com == Info: SSLv3, TLS handshake, Server hello (2): <= Recv SSL data, 74 bytes (0x4a) 0000: 02 00 00 46 03 01 00 00 58 cf 26 e2 e1 65 db 11 ...F....X.&..e.. 0010: bc 6f 26 7b 3b 6d eb 14 5f ad 47 dd 86 ea 4d a3 .o&{;m.._.G...M. 0020: fb 9f b7 2a 54 3e 20 5f 6b 04 5a 12 38 64 5d 18 ...*T> _k.Z.8d]. 0030: 65 9e e9 cd 61 eb 91 c1 16 25 61 30 bb 08 2a 78 e...a....%a0..*x 0040: b8 ee b8 7e f2 65 6a 00 04 00 ...~.ej... == Info: SSLv3, TLS handshake, CERT (11): ... and so on - working nicely eventually get some nice HTML Now I am reaaly stuck. This has been going on for five days, so I am pretty sure that the problem is not with paypal. But what on my system could be interfering with the SSL handshaking done by curl with this particular site? I suppose I could not be offering any certificates that PayPal accepts, but wouldn't I get a reply telling me so, or at least giving an error?

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• Table Sorting in Excel 2010 Cannot Parse the Table Headers Correctly

  - by Truth

  I have a rather weird issue I've never faced before. After defining my table with borders and such, and filling out data in my table, I try to sort my table according to the "ratio" (first) column, from biggest to smallest. When I right click the header and select the corresponding option, the table gets sorted, but the first row is omitted by the sorting function. What I mean is that the first line (with 3.50 ratio) will forever stay at the top line, even when I sort otherwise (by a different column, in a different order). This is my table below, it's tab separated so it's not very readable, but I hope you'll manage. ???? ??????? ????? ??? ???? ??? ??? ??? 14 4 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ?????? 23 8 0 0 0 0 0 0 0 0 0 0 0 0 0 2.88 2.88 ???? 16 4 0 0 0 0 0 0 0 0 0 0 0 0 0 4.00 4.00 ??? 7 2 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ???? 13 4 0 0 0 0 0 0 0 0 0 0 0 0 0 3.25 3.25 ????? 12 4 0 0 0 0 0 0 0 0 0 0 0 0 0 3.00 3.00 ???? 10 4 0 0 0 0 0 0 0 0 0 0 0 0 0 2.50 2.50 ??? 38 12 0 0 0 0 0 0 0 0 0 0 0 0 0 3.17 3.17 ???? 14 4 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ????? 31 10 0 0 0 0 0 0 0 0 0 0 0 0 0 3.10 3.10 ???? 24 8 0 0 0 0 0 0 0 0 0 0 0 0 0 3.00 3.00 ????? 23 8 0 0 0 0 0 0 0 0 0 0 0 0 0 2.88 2.88 ???? 14 4 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ???? 16 4 0 0 0 0 0 0 0 0 0 0 0 0 0 4.00 4.00 ???? 24 8 0 0 0 0 0 0 0 0 0 0 0 0 0 3.00 3.00 ???? 30 10 0 0 0 0 0 0 0 0 0 0 0 0 0 3.00 3.00 ????? 21 6 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ???? 42 12 0 0 0 0 0 0 0 0 0 0 0 0 0 3.50 3.50 ??? 11 4 0 0 0 0 0 0 0 0 0 0 0 0 0 2.75 2.75 ???? 5 2 0 0 0 0 0 0 0 0 0 0 0 0 0 2.50 2.50 ???? 4 2 0 0 0 0 0 0 0 0 0 0 0 0 0 2.00 2.00 ??? 4 2 0 0 0 0 0 0 0 0 0 0 0 0 0 2.00 2.00

  Read the article

• dbus dependency with yum

  - by Hengjie

  Whenever, I try and run yum update I get the following error: [root@server ~]# yum update Loaded plugins: dellsysid, fastestmirror Loading mirror speeds from cached hostfile * base: mirror01.idc.hinet.net * extras: mirror01.idc.hinet.net * rpmforge: fr2.rpmfind.net * updates: mirror01.idc.hinet.net Excluding Packages in global exclude list Finished Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package NetworkManager.x86_64 1:0.7.0-13.el5 set to be updated ---> Package NetworkManager-glib.x86_64 1:0.7.0-13.el5 set to be updated ---> Package SysVinit.x86_64 0:2.86-17.el5 set to be updated ---> Package acl.x86_64 0:2.2.39-8.el5 set to be updated ---> Package acpid.x86_64 0:1.0.4-12.el5 set to be updated ---> Package apr.x86_64 0:1.2.7-11.el5_6.5 set to be updated ---> Package aspell.x86_64 12:0.60.3-12 set to be updated ---> Package audit.x86_64 0:1.8-2.el5 set to be updated ---> Package audit-libs.x86_64 0:1.8-2.el5 set to be updated ---> Package audit-libs-python.x86_64 0:1.8-2.el5 set to be updated ---> Package authconfig.x86_64 0:5.3.21-7.el5 set to be updated ---> Package autofs.x86_64 1:5.0.1-0.rc2.163.el5 set to be updated ---> Package bash.x86_64 0:3.2-32.el5 set to be updated ---> Package bind.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package bind-libs.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package bind-utils.x86_64 30:9.3.6-20.P1.el5 set to be updated ---> Package binutils.x86_64 0:2.17.50.0.6-20.el5 set to be updated ---> Package centos-release.x86_64 10:5-8.el5.centos set to be updated ---> Package centos-release-notes.x86_64 0:5.8-0 set to be updated ---> Package coreutils.x86_64 0:5.97-34.el5_8.1 set to be updated ---> Package cpp.x86_64 0:4.1.2-52.el5 set to be updated ---> Package cpuspeed.x86_64 1:1.2.1-10.el5 set to be updated ---> Package crash.x86_64 0:5.1.8-1.el5.centos set to be updated ---> Package cryptsetup-luks.x86_64 0:1.0.3-8.el5 set to be updated ---> Package cups.x86_64 1:1.3.7-30.el5 set to be updated ---> Package cups-libs.x86_64 1:1.3.7-30.el5 set to be updated ---> Package curl.x86_64 0:7.15.5-15.el5 set to be updated --> Processing Dependency: dbus = 1.1.2-15.el5_6 for package: dbus-libs ---> Package dbus.x86_64 0:1.1.2-16.el5_7 set to be updated ---> Package dbus-libs.x86_64 0:1.1.2-16.el5_7 set to be updated ---> Package device-mapper.x86_64 0:1.02.67-2.el5 set to be updated ---> Package device-mapper-event.x86_64 0:1.02.67-2.el5 set to be updated ---> Package device-mapper-multipath.x86_64 0:0.4.7-48.el5_8.1 set to be updated ---> Package dhclient.x86_64 12:3.0.5-31.el5 set to be updated ---> Package dmidecode.x86_64 1:2.11-1.el5 set to be updated ---> Package dmraid.x86_64 0:1.0.0.rc13-65.el5 set to be updated ---> Package dmraid-events.x86_64 0:1.0.0.rc13-65.el5 set to be updated ---> Package dump.x86_64 0:0.4b41-6.el5 set to be updated ---> Package e2fsprogs.x86_64 0:1.39-33.el5 set to be updated ---> Package e2fsprogs-devel.x86_64 0:1.39-33.el5 set to be updated ---> Package e2fsprogs-libs.x86_64 0:1.39-33.el5 set to be updated ---> Package ecryptfs-utils.x86_64 0:75-8.el5 set to be updated ---> Package file.x86_64 0:4.17-21 set to be updated ---> Package finger.x86_64 0:0.17-33 set to be updated ---> Package firstboot-tui.x86_64 0:1.4.27.9-1.el5.centos set to be updated ---> Package freetype.x86_64 0:2.2.1-28.el5_7.2 set to be updated ---> Package freetype-devel.x86_64 0:2.2.1-28.el5_7.2 set to be updated ---> Package ftp.x86_64 0:0.17-37.el5 set to be updated ---> Package gamin.x86_64 0:0.1.7-10.el5 set to be updated ---> Package gamin-python.x86_64 0:0.1.7-10.el5 set to be updated ---> Package gawk.x86_64 0:3.1.5-15.el5 set to be updated ---> Package gcc.x86_64 0:4.1.2-52.el5 set to be updated ---> Package gcc-c++.x86_64 0:4.1.2-52.el5 set to be updated ---> Package glibc.i686 0:2.5-81.el5_8.1 set to be updated ---> Package glibc.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-common.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-devel.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package glibc-headers.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package gnutls.x86_64 0:1.4.1-7.el5_8.2 set to be updated ---> Package groff.x86_64 0:1.18.1.1-13.el5 set to be updated ---> Package gtk2.x86_64 0:2.10.4-21.el5_7.7 set to be updated ---> Package gzip.x86_64 0:1.3.5-13.el5.centos set to be updated ---> Package hmaccalc.x86_64 0:0.9.6-4.el5 set to be updated ---> Package htop.x86_64 0:1.0.1-2.el5.rf set to be updated ---> Package hwdata.noarch 0:0.213.26-1.el5 set to be updated ---> Package ifd-egate.x86_64 0:0.05-17.el5 set to be updated ---> Package initscripts.x86_64 0:8.45.42-1.el5.centos set to be updated ---> Package iproute.x86_64 0:2.6.18-13.el5 set to be updated ---> Package iptables.x86_64 0:1.3.5-9.1.el5 set to be updated ---> Package iptables-ipv6.x86_64 0:1.3.5-9.1.el5 set to be updated ---> Package iscsi-initiator-utils.x86_64 0:6.2.0.872-13.el5 set to be updated ---> Package kernel.x86_64 0:2.6.18-308.1.1.el5 set to be installed ---> Package kernel-headers.x86_64 0:2.6.18-308.1.1.el5 set to be updated ---> Package kpartx.x86_64 0:0.4.7-48.el5_8.1 set to be updated ---> Package krb5-devel.x86_64 0:1.6.1-70.el5 set to be updated ---> Package krb5-libs.x86_64 0:1.6.1-70.el5 set to be updated ---> Package krb5-workstation.x86_64 0:1.6.1-70.el5 set to be updated ---> Package ksh.x86_64 0:20100621-5.el5_8.1 set to be updated ---> Package kudzu.x86_64 0:1.2.57.1.26-3.el5.centos set to be updated ---> Package less.x86_64 0:436-9.el5 set to be updated ---> Package lftp.x86_64 0:3.7.11-7.el5 set to be updated ---> Package libX11.x86_64 0:1.0.3-11.el5_7.1 set to be updated ---> Package libX11-devel.x86_64 0:1.0.3-11.el5_7.1 set to be updated ---> Package libXcursor.x86_64 0:1.1.7-1.2 set to be updated ---> Package libacl.x86_64 0:2.2.39-8.el5 set to be updated ---> Package libgcc.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libgomp.x86_64 0:4.4.6-3.el5.1 set to be updated ---> Package libpng.x86_64 2:1.2.10-16.el5_8 set to be updated ---> Package libpng-devel.x86_64 2:1.2.10-16.el5_8 set to be updated ---> Package libsmbios.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package libstdc++.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libstdc++-devel.x86_64 0:4.1.2-52.el5 set to be updated ---> Package libsysfs.x86_64 0:2.1.0-1.el5 set to be updated ---> Package libusb.x86_64 0:0.1.12-6.el5 set to be updated ---> Package libvolume_id.x86_64 0:095-14.27.el5_7.1 set to be updated ---> Package libxml2.x86_64 0:2.6.26-2.1.15.el5_8.2 set to be updated ---> Package libxml2-python.x86_64 0:2.6.26-2.1.15.el5_8.2 set to be updated ---> Package logrotate.x86_64 0:3.7.4-12 set to be updated ---> Package lsof.x86_64 0:4.78-6 set to be updated ---> Package lvm2.x86_64 0:2.02.88-7.el5 set to be updated ---> Package m2crypto.x86_64 0:0.16-8.el5 set to be updated ---> Package man.x86_64 0:1.6d-2.el5 set to be updated ---> Package man-pages.noarch 0:2.39-20.el5 set to be updated ---> Package mcelog.x86_64 1:0.9pre-1.32.el5 set to be updated ---> Package mesa-libGL.x86_64 0:6.5.1-7.10.el5 set to be updated ---> Package mesa-libGL-devel.x86_64 0:6.5.1-7.10.el5 set to be updated ---> Package microcode_ctl.x86_64 2:1.17-1.56.el5 set to be updated ---> Package mkinitrd.x86_64 0:5.1.19.6-75.el5 set to be updated ---> Package mktemp.x86_64 3:1.5-24.el5 set to be updated --> Processing Dependency: nash = 5.1.19.6-68.el5_6.1 for package: mkinitrd ---> Package nash.x86_64 0:5.1.19.6-75.el5 set to be updated ---> Package net-snmp.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-devel.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-libs.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-snmp-utils.x86_64 1:5.3.2.2-17.el5 set to be updated ---> Package net-tools.x86_64 0:1.60-82.el5 set to be updated ---> Package nfs-utils.x86_64 1:1.0.9-60.el5 set to be updated ---> Package nfs-utils-lib.x86_64 0:1.0.8-7.9.el5 set to be updated ---> Package nscd.x86_64 0:2.5-81.el5_8.1 set to be updated ---> Package nspr.x86_64 0:4.8.9-1.el5_8 set to be updated ---> Package nspr-devel.x86_64 0:4.8.9-1.el5_8 set to be updated ---> Package nss.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss-devel.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss-tools.x86_64 0:3.13.1-5.el5_8 set to be updated ---> Package nss_ldap.x86_64 0:253-49.el5 set to be updated ---> Package ntp.x86_64 0:4.2.2p1-15.el5.centos.1 set to be updated ---> Package numactl.x86_64 0:0.9.8-12.el5_6 set to be updated ---> Package oddjob.x86_64 0:0.27-12.el5 set to be updated ---> Package oddjob-libs.x86_64 0:0.27-12.el5 set to be updated ---> Package openldap.x86_64 0:2.3.43-25.el5 set to be updated ---> Package openssh.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssh-clients.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssh-server.x86_64 0:4.3p2-82.el5 set to be updated ---> Package openssl.i686 0:0.9.8e-22.el5_8.1 set to be updated ---> Package openssl.x86_64 0:0.9.8e-22.el5_8.1 set to be updated ---> Package openssl-devel.x86_64 0:0.9.8e-22.el5_8.1 set to be updated ---> Package pam_krb5.x86_64 0:2.2.14-22.el5 set to be updated ---> Package pam_pkcs11.x86_64 0:0.5.3-26.el5 set to be updated ---> Package pango.x86_64 0:1.14.9-8.el5.centos.3 set to be updated ---> Package parted.x86_64 0:1.8.1-29.el5 set to be updated ---> Package pciutils.x86_64 0:3.1.7-5.el5 set to be updated ---> Package perl.x86_64 4:5.8.8-38.el5 set to be updated ---> Package perl-Compress-Raw-Bzip2.x86_64 0:2.037-1.el5.rf set to be updated ---> Package perl-Compress-Raw-Zlib.x86_64 0:2.037-1.el5.rf set to be updated ---> Package perl-rrdtool.x86_64 0:1.4.7-1.el5.rf set to be updated ---> Package poppler.x86_64 0:0.5.4-19.el5 set to be updated ---> Package poppler-utils.x86_64 0:0.5.4-19.el5 set to be updated ---> Package popt.x86_64 0:1.10.2.3-28.el5_8 set to be updated ---> Package postgresql-libs.x86_64 0:8.1.23-1.el5_7.3 set to be updated ---> Package procps.x86_64 0:3.2.7-18.el5 set to be updated ---> Package proftpd.x86_64 0:1.3.4a-1.el5.rf set to be updated --> Processing Dependency: perl(Mail::Sendmail) for package: proftpd ---> Package python.x86_64 0:2.4.3-46.el5 set to be updated ---> Package python-ctypes.x86_64 0:1.0.2-3.el5 set to be updated ---> Package python-libs.x86_64 0:2.4.3-46.el5 set to be updated ---> Package python-smbios.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package rhpl.x86_64 0:0.194.1-2 set to be updated ---> Package rmt.x86_64 0:0.4b41-6.el5 set to be updated ---> Package rng-utils.x86_64 1:2.0-5.el5 set to be updated ---> Package rpm.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-build.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-devel.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-libs.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rpm-python.x86_64 0:4.4.2.3-28.el5_8 set to be updated ---> Package rrdtool.x86_64 0:1.4.7-1.el5.rf set to be updated ---> Package rsh.x86_64 0:0.17-40.el5_7.1 set to be updated ---> Package rsync.x86_64 0:3.0.6-4.el5_7.1 set to be updated ---> Package ruby.x86_64 0:1.8.5-24.el5 set to be updated ---> Package ruby-libs.x86_64 0:1.8.5-24.el5 set to be updated ---> Package sblim-sfcb.x86_64 0:1.3.11-49.el5 set to be updated ---> Package sblim-sfcc.x86_64 0:2.2.2-49.el5 set to be updated ---> Package selinux-policy.noarch 0:2.4.6-327.el5 set to be updated ---> Package selinux-policy-targeted.noarch 0:2.4.6-327.el5 set to be updated ---> Package setup.noarch 0:2.5.58-9.el5 set to be updated ---> Package shadow-utils.x86_64 2:4.0.17-20.el5 set to be updated ---> Package smartmontools.x86_64 1:5.38-3.el5 set to be updated ---> Package smbios-utils-bin.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package smbios-utils-python.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package sos.noarch 0:1.7-9.62.el5 set to be updated ---> Package srvadmin-omilcore.x86_64 0:6.5.0-1.452.1.el5 set to be updated ---> Package strace.x86_64 0:4.5.18-11.el5_8 set to be updated ---> Package subversion.x86_64 0:1.6.11-7.el5_6.4 set to be updated ---> Package sudo.x86_64 0:1.7.2p1-13.el5 set to be updated ---> Package sysfsutils.x86_64 0:2.1.0-1.el5 set to be updated ---> Package syslinux.x86_64 0:3.11-7 set to be updated ---> Package system-config-network-tui.noarch 0:1.3.99.21-1.el5 set to be updated ---> Package talk.x86_64 0:0.17-31.el5 set to be updated ---> Package tar.x86_64 2:1.15.1-31.el5 set to be updated ---> Package traceroute.x86_64 3:2.0.1-6.el5 set to be updated ---> Package tzdata.x86_64 0:2012b-3.el5 set to be updated ---> Package udev.x86_64 0:095-14.27.el5_7.1 set to be updated ---> Package util-linux.x86_64 0:2.13-0.59.el5 set to be updated ---> Package vixie-cron.x86_64 4:4.1-81.el5 set to be updated ---> Package wget.x86_64 0:1.11.4-3.el5_8.1 set to be updated ---> Package xinetd.x86_64 2:2.3.14-16.el5 set to be updated ---> Package yp-tools.x86_64 0:2.9-2.el5 set to be updated ---> Package ypbind.x86_64 3:1.19-12.el5_6.1 set to be updated ---> Package yum.noarch 0:3.2.22-39.el5.centos set to be updated ---> Package yum-dellsysid.x86_64 0:2.2.27-3.2.el5 set to be updated ---> Package yum-fastestmirror.noarch 0:1.1.16-21.el5.centos set to be updated ---> Package zlib.x86_64 0:1.2.3-4.el5 set to be updated ---> Package zlib-devel.x86_64 0:1.2.3-4.el5 set to be updated --> Running transaction check --> Processing Dependency: dbus = 1.1.2-15.el5_6 for package: dbus-libs --> Processing Dependency: nash = 5.1.19.6-68.el5_6.1 for package: mkinitrd ---> Package perl-Mail-Sendmail.noarch 0:0.79-1.2.el5.rf set to be updated base/filelists | 3.5 MB 00:00 dell-omsa-indep/filelists | 195 kB 00:01 dell-omsa-specific/filelists | 1.0 kB 00:00 extras/filelists_db | 224 kB 00:00 rpmforge/filelists | 4.8 MB 00:06 updates/filelists_db | 715 kB 00:00 --> Finished Dependency Resolution dbus-libs-1.1.2-15.el5_6.i386 from installed has depsolving problems --> Missing Dependency: dbus = 1.1.2-15.el5_6 is needed by package dbus-libs-1.1.2-15.el5_6.i386 (installed) mkinitrd-5.1.19.6-68.el5_6.1.i386 from installed has depsolving problems --> Missing Dependency: nash = 5.1.19.6-68.el5_6.1 is needed by package mkinitrd-5.1.19.6-68.el5_6.1.i386 (installed) Error: Missing Dependency: nash = 5.1.19.6-68.el5_6.1 is needed by package mkinitrd-5.1.19.6-68.el5_6.1.i386 (installed) Error: Missing Dependency: dbus = 1.1.2-15.el5_6 is needed by package dbus-libs-1.1.2-15.el5_6.i386 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The program package-cleanup is found in the yum-utils package. I have tried running package-cleanup --dupes and package-cleanup --problems but to no avail.

  Read the article

• New CentOS/cPanel servers showing high load averages at idle

  - by Jax

  I have taken delivery of two identically specced CentOS/cPanel servers, showing the same behaviour of a resting load average of 1.30, 1.21, 1.16 and yet the CPU is sitting 100% idle. Hardware: Xeon(R) CPU E3-1270 4GB RAM Behavior:- top shows CPU 99.9% idle virtually no disk IO Some command output :- uname -a Linux server.myserver.com 2.6.18-308.4.1.el5PAE #1 SMP Tue Apr 17 17:47:38 EDT 2012 i686 i686 i386 GNU/Linux top top - 10:37:50 up 1:47, 1 user, load average: 1.28, 1.20, 1.17 Tasks: 199 total, 1 running, 198 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 4125104k total, 438764k used, 3686340k free, 25788k buffers Swap: 2096440k total, 0k used, 2096440k free, 291080k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2160 640 552 S 0.0 0.0 0:00.89 init 2 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/2 9 root 35 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/2 10 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/2 11 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/3 12 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/3 13 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/3 14 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/4 15 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/4 16 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/4 17 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/5 18 root 38 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/5 19 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/5 20 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/6 21 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/6 22 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/6 23 root RT -5 0 0 0 S 0.0 0.0 0:00.00 migration/7 24 root 34 19 0 0 0 S 0.0 0.0 0:00.00 ksoftirqd/7 25 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/7 26 root 10 -5 0 0 0 S 0.0 0.0 0:06.42 events/0 27 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/1 28 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/2 29 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/3 30 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/4 31 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/5 32 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/6 33 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 events/7 34 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 khelper 35 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kthread 45 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/0 46 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/1 47 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/2 48 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/3 49 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/4 50 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/5 51 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/6 52 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kblockd/7 53 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 kacpid 189 root 11 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/0 190 root 11 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/1 191 root 12 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/2 192 root 12 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/3 193 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/4 194 root 13 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/5 195 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/6 196 root 14 -5 0 0 0 S 0.0 0.0 0:00.00 cqueue/7 199 root 10 -5 0 0 0 S 0.0 0.0 0:00.00 khubd ps axf PID TTY STAT TIME COMMAND 1 ? Ss 0:00 init [3] 2 ? S< 0:00 [migration/0] 3 ? SN 0:00 [ksoftirqd/0] 4 ? S< 0:00 [watchdog/0] 5 ? S< 0:00 [migration/1] 6 ? SN 0:00 [ksoftirqd/1] 7 ? S< 0:00 [watchdog/1] 8 ? S< 0:00 [migration/2] 9 ? SN 0:00 [ksoftirqd/2] 10 ? S< 0:00 [watchdog/2] 11 ? S< 0:00 [migration/3] 12 ? SN 0:00 [ksoftirqd/3] 13 ? S< 0:00 [watchdog/3] 14 ? S< 0:00 [migration/4] 15 ? SN 0:00 [ksoftirqd/4] 16 ? S< 0:00 [watchdog/4] 17 ? S< 0:00 [migration/5] 18 ? SN 0:00 [ksoftirqd/5] 19 ? S< 0:00 [watchdog/5] 20 ? S< 0:00 [migration/6] 21 ? SN 0:00 [ksoftirqd/6] 22 ? S< 0:00 [watchdog/6] 23 ? S< 0:00 [migration/7] 24 ? SN 0:00 [ksoftirqd/7] 25 ? S< 0:00 [watchdog/7] 26 ? S< 0:06 [events/0] 27 ? S< 0:00 [events/1] 28 ? S< 0:00 [events/2] 29 ? S< 0:00 [events/3] 30 ? S< 0:00 [events/4] 31 ? S< 0:00 [events/5] 32 ? S< 0:00 [events/6] 33 ? S< 0:00 [events/7] 34 ? S< 0:00 [khelper] 35 ? S< 0:00 [kthread] 45 ? S< 0:00 \_ [kblockd/0] 46 ? S< 0:00 \_ [kblockd/1] 47 ? S< 0:00 \_ [kblockd/2] 48 ? S< 0:00 \_ [kblockd/3] 49 ? S< 0:00 \_ [kblockd/4] 50 ? S< 0:00 \_ [kblockd/5] 51 ? S< 0:00 \_ [kblockd/6] 52 ? S< 0:00 \_ [kblockd/7] 53 ? S< 0:00 \_ [kacpid] 189 ? S< 0:00 \_ [cqueue/0] 190 ? S< 0:00 \_ [cqueue/1] 191 ? S< 0:00 \_ [cqueue/2] 192 ? S< 0:00 \_ [cqueue/3] 193 ? S< 0:00 \_ [cqueue/4] 194 ? S< 0:00 \_ [cqueue/5] 195 ? S< 0:00 \_ [cqueue/6] 196 ? S< 0:00 \_ [cqueue/7] 199 ? S< 0:00 \_ [khubd] 201 ? S< 0:00 \_ [kseriod] 301 ? S 0:00 \_ [khungtaskd] 302 ? S 0:00 \_ [pdflush] 303 ? S 0:00 \_ [pdflush] 304 ? S< 0:00 \_ [kswapd0] 305 ? S< 0:00 \_ [aio/0] 306 ? S< 0:00 \_ [aio/1] 307 ? S< 0:00 \_ [aio/2] 308 ? S< 0:00 \_ [aio/3] 309 ? S< 0:00 \_ [aio/4] 310 ? S< 0:00 \_ [aio/5] 311 ? S< 0:00 \_ [aio/6] 312 ? S< 0:00 \_ [aio/7] 472 ? S< 0:00 \_ [kpsmoused] 551 ? S< 0:00 \_ [ata/0] 552 ? S< 0:00 \_ [ata/1] 553 ? S< 0:00 \_ [ata/2] 554 ? S< 0:00 \_ [ata/3] 555 ? S< 0:00 \_ [ata/4] 556 ? S< 0:00 \_ [ata/5] 557 ? S< 0:00 \_ [ata/6] 558 ? S< 0:00 \_ [ata/7] 559 ? S< 0:00 \_ [ata_aux] 569 ? S< 0:00 \_ [scsi_eh_0] 570 ? S< 0:00 \_ [scsi_eh_1] 571 ? S< 0:00 \_ [scsi_eh_2] 572 ? S< 0:00 \_ [scsi_eh_3] 573 ? S< 0:00 \_ [scsi_eh_4] 574 ? S< 0:00 \_ [scsi_eh_5] 593 ? S< 0:00 \_ [kstriped] 630 ? S< 0:00 \_ [kjournald] 655 ? S< 0:00 \_ [kauditd] 1860 ? S< 0:00 \_ [kmpathd/0] 1861 ? S< 0:00 \_ [kmpathd/1] 1862 ? S< 0:00 \_ [kmpathd/2] 1863 ? S< 0:00 \_ [kmpathd/3] 1864 ? S< 0:00 \_ [kmpathd/4] 1865 ? S< 0:00 \_ [kmpathd/5] 1866 ? S< 0:00 \_ [kmpathd/6] 1867 ? S< 0:00 \_ [kmpathd/7] 1868 ? S< 0:00 \_ [kmpath_handlerd] 1902 ? S< 0:00 \_ [kjournald] 1904 ? S< 0:00 \_ [kjournald] 1906 ? S< 0:00 \_ [kjournald] 1908 ? S< 0:00 \_ [kjournald] 1910 ? S< 0:00 \_ [kjournald] 2184 ? S< 0:00 \_ [iscsi_eh] 2288 ? S< 0:00 \_ [cnic_wq] 2298 ? S< 0:00 \_ [bnx2i_thread/0] 2299 ? S< 0:00 \_ [bnx2i_thread/1] 2300 ? S< 0:00 \_ [bnx2i_thread/2] 2301 ? S< 0:00 \_ [bnx2i_thread/3] 2302 ? S< 0:00 \_ [bnx2i_thread/4] 2303 ? S< 0:00 \_ [bnx2i_thread/5] 2304 ? S< 0:00 \_ [bnx2i_thread/6] 2305 ? S< 0:00 \_ [bnx2i_thread/7] 2330 ? S< 0:00 \_ [ib_addr] 2359 ? S< 0:00 \_ [ib_mcast] 2360 ? S< 0:00 \_ [ib_inform] 2361 ? S< 0:00 \_ [local_sa] 2371 ? S< 0:00 \_ [iw_cm_wq] 2381 ? S< 0:00 \_ [ib_cm/0] 2382 ? S< 0:00 \_ [ib_cm/1] 2383 ? S< 0:00 \_ [ib_cm/2] 2384 ? S< 0:00 \_ [ib_cm/3] 2385 ? S< 0:00 \_ [ib_cm/4] 2386 ? S< 0:00 \_ [ib_cm/5] 2387 ? S< 0:00 \_ [ib_cm/6] 2388 ? S< 0:00 \_ [ib_cm/7] 2398 ? S< 0:00 \_ [rdma_cm] 2684 ? S< 0:00 \_ [bond0] 2882 ? S< 0:00 \_ [bond1] 3195 ? S< 0:00 \_ [kondemand/0] 3197 ? S< 0:00 \_ [kondemand/1] 3198 ? S< 0:00 \_ [kondemand/2] 3199 ? S< 0:00 \_ [kondemand/3] 3200 ? S< 0:00 \_ [kondemand/4] 3201 ? S< 0:00 \_ [kondemand/5] 3202 ? S< 0:00 \_ [kondemand/6] 3203 ? S< 0:00 \_ [kondemand/7] 688 ? S<s 0:00 /sbin/udevd -d 2425 ? S<Lsl 0:00 iscsiuio 2432 ? Ss 0:00 iscsid 2434 ? S<Ls 0:00 iscsid 3061 ? S<sl 0:00 auditd 3063 ? S<sl 0:00 \_ /sbin/audispd 3121 ? Ss 0:00 syslogd -m 0 3124 ? Ss 0:00 klogd -x 3220 ? Ss 0:00 irqbalance 3278 ? Ss 0:00 dbus-daemon --system 3324 ? Ss 0:00 /usr/sbin/acpid 3337 ? Ss 0:00 hald 3338 ? S 0:00 \_ hald-runner 3345 ? S 0:00 \_ hald-addon-acpi: listening on acpid socket /var/run/acpid.socket 3349 ? S 0:00 \_ hald-addon-keyboard: listening on /dev/input/event1 3360 ? S 0:00 \_ hald-addon-storage: polling /dev/sr0 3413 ? Ssl 0:00 automount 3435 ? Ssl 0:00 /usr/sbin/named -u named 3466 ? Ss 0:00 /usr/sbin/sshd 4072 ? Ss 0:00 \_ sshd: root@pts/0 4078 pts/0 Ss 0:00 \_ -bash 5436 pts/0 R+ 0:00 \_ ps axf 3484 ? Ss 0:00 xinetd -stayalive -pidfile /var/run/xinetd.pid 3500 ? SLs 0:00 ntpd -u ntp:ntp -p /var/run/ntpd.pid -g 3514 ? S 0:00 /bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/server.myserver.com.pid 3575 ? Sl 0:00 \_ /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --log-error=/var/lib/mysql/server.myserver.com.err --pid-fil 3687 ? Ss 0:00 /usr/sbin/exim -bd -q1h 3709 ? Ss 0:00 /usr/sbin/dovecot 3710 ? S 0:00 \_ dovecot-auth 3725 ? S 0:00 \_ pop3-login 3726 ? S 0:00 \_ pop3-login 3727 ? S 0:00 \_ imap-login 3728 ? S 0:00 \_ imap-login 3729 ? Ss 0:00 /usr/local/apache/bin/httpd -k start -DSSL 4326 ? S 0:00 \_ /usr/bin/perl /usr/local/cpanel/bin/leechprotect 4332 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4333 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4334 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4335 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4336 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4337 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4382 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4383 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 4384 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 5389 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 5390 ? S 0:00 \_ /usr/local/apache/bin/httpd -k start -DSSL 3741 ? Ss 0:00 pure-ftpd (SERVER) 3746 ? S 0:00 /usr/sbin/pure-authd -s /var/run/ftpd.sock -r /usr/sbin/pureauth 3759 ? Ss 0:00 crond 3772 ? Ss 0:00 /usr/sbin/atd 3909 ? S 0:00 cpsrvd (SSL) - waiting for connections 5435 ? Z 0:00 \_ [cpsrvd-ssl] <defunct> 3931 ? S 0:00 queueprocd - wait to process a task 3948 ? S 0:00 tailwatchd 3954 ? SN 0:00 cpanellogd - sleeping for logs 4003 ? Ss 0:00 ./nimbus /opt/nimsoft 4016 ? S 0:00 \_ nimbus(controller) 4053 ? Sl 0:00 \_ nimbus(spooler) 4066 ? S 0:00 \_ nimbus(hdb) 4069 ? S 0:00 \_ nimbus(cdm) 4070 ? S 0:00 \_ nimbus(processes) 4023 ? S 0:00 /usr/sbin/smartd -q never 4027 tty1 Ss+ 0:00 /sbin/mingetty tty1 4028 tty2 Ss+ 0:00 /sbin/mingetty tty2 4029 tty3 Ss+ 0:00 /sbin/mingetty tty3 4030 tty4 Ss+ 0:00 /sbin/mingetty tty4 4031 tty5 Ss+ 0:00 /sbin/mingetty tty5 4033 tty6 Ss+ 0:00 /sbin/mingetty tty6 4035 ttyS1 Ss+ 0:00 /sbin/agetty -h -L ttyS1 19200 vt100 vmstat 10 6 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 3718136 25684 257424 0 0 8 3 127 189 0 0 100 0 0 0 0 0 3718136 25700 257420 0 0 0 7 1013 1500 0 0 100 0 0 0 0 0 3718136 25700 257424 0 0 0 1 1013 1551 0 0 100 0 0 0 0 0 3718136 25700 257424 0 0 0 0 1012 1469 0 0 100 0 0 1 0 0 3712680 25716 257424 0 0 0 2 1013 1542 0 0 100 0 0 0 0 0 3718376 25740 257424 0 0 0 46 1017 1534 0 0 100 0 0 Can anyone advise me as to what is the cause of and how I may resolve this behaviour? A kernel/driver conflict perhaps? I don't see any processes in R or D state that might inflate the load averages artificially, I realise it may be considered low in an 8 thread system but its higher at idle than any normal behaviour I've previously come across. Thanks in advance for your time. Edit: iotop Total DISK READ: 0.00 B/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 26 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.29 % [events/0] 3205 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.10 % [kondemand/2] 3208 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/5] 3209 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/6] 3207 be/3 root 0.00 B/s 0.00 B/s 0.10 % 0.00 % [kondemand/4] 3210 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/7] 3227 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % irqbalance 3288 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [rpciod/1] 3287 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [rpciod/0] 3206 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kondemand/3] 3069 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % auditd 3070 be/2 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % audispd 655 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kauditd] 3619 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % automount 3 be/7 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [ksoftirqd/0] 3068 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % auditd 29 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/3] 4 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/0] 7 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/1] 10 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/2] 13 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/3] 16 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/4] 19 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/5] 22 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/6] 25 rt/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [watchdog/7] 27 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/1] 28 be/3 root 0.00 B/s 0.00 B/s 0.29 % 0.00 % [events/2] 30 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/4] 31 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/5] 32 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/6] 33 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [events/7] 34 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [khelper] 35 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kthread] 45 be/3 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % [kblockd/0]

  Read the article

• How to obtain a random sub-datatable from another data table

  - by developerit

  Introduction In this article, I’ll show how to get a random subset of data from a DataTable. This is useful when you already have queries that are filtered correctly but returns all the rows. Analysis I came across this situation when I wanted to display a random tag cloud. I already had the query to get the keywords ordered by number of clicks and I wanted to created a tag cloud. Tags that are the most popular should have more chance to get picked and should be displayed larger than less popular ones. Implementation In this code snippet, there is everything you need. ' Min size, in pixel for the tag Private Const MIN_FONT_SIZE As Integer = 9 ' Max size, in pixel for the tag Private Const MAX_FONT_SIZE As Integer = 14 ' Basic function that retreives Tags from a DataBase Public Shared Function GetTags() As MediasTagsDataTable ' Simple call to the TableAdapter, to get the Tags ordered by number of clicks Dim dt As MediasTagsDataTable = taMediasTags.GetDataValide ' If the query returned no result, return an empty DataTable If dt Is Nothing OrElse dt.Rows.Count < 1 Then Return New MediasTagsDataTable End If ' Set the font-size of the group of data ' We are dividing our results into sub set, according to their number of clicks ' Example: 10 results -> [0,2] will get font size 9, [3,5] will get font size 10, [6,8] wil get 11, ... ' This is the number of elements in one group Dim groupLenth As Integer = CType(Math.Floor(dt.Rows.Count / (MAX_FONT_SIZE - MIN_FONT_SIZE)), Integer) ' Counter of elements in the same group Dim counter As Integer = 0 ' Counter of groups Dim groupCounter As Integer = 0 ' Loop througt the list For Each row As MediasTagsRow In dt ' Set the font-size in a custom column row.c_FontSize = MIN_FONT_SIZE + groupCounter ' Increment the counter counter += 1 ' If the group counter is less than the counter If groupLenth <= counter Then ' Start a new group counter = 0 groupCounter += 1 End If Next ' Return the new DataTable with font-size Return dt End Function ' Function that generate the random sub set Public Shared Function GetRandomSampleTags(ByVal KeyCount As Integer) As MediasTagsDataTable ' Get the data Dim dt As MediasTagsDataTable = GetTags() ' Create a new DataTable that will contains the random set Dim rep As MediasTagsDataTable = New MediasTagsDataTable ' Count the number of row in the new DataTable Dim count As Integer = 0 ' Random number generator Dim rand As New Random() While count < KeyCount Randomize() ' Pick a random row Dim r As Integer = rand.Next(0, dt.Rows.Count - 1) Dim tmpRow As MediasTagsRow = dt(r) ' Import it into the new DataTable rep.ImportRow(tmpRow) ' Remove it from the old one, to be sure not to pick it again dt.Rows.RemoveAt(r) ' Increment the counter count += 1 End While ' Return the new sub set Return rep End Function Pro’s This method is good because it doesn’t require much work to get it work fast. It is a good concept when you are working with small tables, let says less than 100 records. Con’s If you have more than 100 records, out of memory exception may occur since we are coping and duplicating rows. I would consider using a stored procedure instead.

  Read the article

• SSH problems (ssh_exchange_identification: read: Connection reset by peer)

  - by kSiR

  I was running 11.10 and decided to do the full upgrade and come up to 12.04 after the update SSH (not SSHD) is now misbehaving when attempting to connect to other OpenSSH instances. I say OpenSSH as I am running a DropBear sshd on my router and I am able to connect to it. When attempting to connect to an OpenSSH server risk@skynet:~/.ssh$ ssh -vvv risk@someserver OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/risk/.ssh/config debug3: key names ok: [[email protected],[email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-rsa,ssh-dss] debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to someserver [someserver] port 22. debug1: Connection established. debug1: identity file /home/risk/.ssh/id_rsa type -1 debug1: identity file /home/risk/.ssh/id_rsa-cert type -1 debug1: identity file /home/risk/.ssh/id_dsa type -1 debug1: identity file /home/risk/.ssh/id_dsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/home/risk/.ssh/id_ecdsa" as a RSA1 public key debug1: identity file /home/risk/.ssh/id_ecdsa type 3 debug1: Checking blacklist file /usr/share/ssh/blacklist.ECDSA-521 debug1: Checking blacklist file /etc/ssh/blacklist.ECDSA-521 debug1: identity file /home/risk/.ssh/id_ecdsa-cert type -1 ssh_exchange_identification: read: Connection reset by peer risk@skynet:~/.ssh$ DropBear instance risk@skynet:~/.ssh$ ssh -vvv root@darkness OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/risk/.ssh/config debug3: key names ok: [[email protected],[email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-rsa,ssh-dss] debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to darkness [192.168.1.1] port 22. debug1: Connection established. debug1: identity file /home/risk/.ssh/id_rsa type -1 debug1: identity file /home/risk/.ssh/id_rsa-cert type -1 debug1: identity file /home/risk/.ssh/id_dsa type -1 debug1: identity file /home/risk/.ssh/id_dsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/home/risk/.ssh/id_ecdsa" as a RSA1 public key debug1: identity file /home/risk/.ssh/id_ecdsa type 3 debug1: Checking blacklist file /usr/share/ssh/blacklist.ECDSA-521 debug1: Checking blacklist file /etc/ssh/blacklist.ECDSA-521 debug1: identity file /home/risk/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version dropbear_0.52 debug1: no match: dropbear_0.52 ... I have googled and ran most ALL fixes recommend both from the Debian and Arch sides and none of them seem to resolve my issue. Any ideas?

  Read the article

• Using Unity – Part 1

  - by nmarun

  I have been going through implementing some IoC pattern using Unity and so I decided to share my learnings (I know that’s not an English word, but you get the point). Ok, so I have an ASP.net project named ProductWeb and a class library called ProductModel. In the model library, I have a class called Product: 1: public class Product 2: { 3: public string Name { get; set; } 4: public string Description { get; set; } 5:  6: public Product() 7: { 8: Name = "iPad"; 9: Description = "Not just a reader!"; 10: } 11:  12: public string WriteProductDetails() 13: { 14: return string.Format("Name: {0} Description: {1}", Name, Description); 15: } 16: } In the Page_Load event of the default.aspx, I’ll need something like: 1: Product product = new Product(); 2: productDetailsLabel.Text = product.WriteProductDetails(); Now, let’s go ‘Unity’fy this application. I assume you have all the bits for the pattern. If not, get it from here. I found this schematic representation of Unity pattern from the above link. This image might not make much sense to you now, but as we proceed, things will get better. The first step to implement the Inversion of Control pattern is to create interfaces that your types will implement. An IProduct interface is added to the ProductModel project. 1: public interface IProduct 2: { 3: string WriteProductDetails(); 4: } Let’s make our Product class to implement the IProduct interface. The application will compile and run as before despite the changes made. Add the following references to your web project: Microsoft.Practices.Unity Microsoft.Practices.Unity.Configuration Microsoft.Practices.Unity.StaticFactory Microsoft.Practices.ObjectBuilder2 We need to add a few lines to the web.config file. The line below tells what version of Unity pattern we’ll be using. 1: <configSections> 2: <section name="unity" type="Microsoft.Practices.Unity.Configuration.UnityConfigurationSection, Microsoft.Practices.Unity.Configuration, Version=1.2.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35"/> 3: </configSections> Add another block with the same name as the section name declared above – ‘unity’. 1: <unity> 2: <typeAliases> 3: <!--Custom object types--> 4: <typeAlias alias="IProduct" type="ProductModel.IProduct, ProductModel"/> 5: <typeAlias alias="Product" type="ProductModel.Product, ProductModel"/> 6: </typeAliases> 7: <containers> 8: <container name="unityContainer"> 9: <types> 10: <type type="IProduct" mapTo="Product"/> 11: </types> 12: </container> 13: </containers> 14: </unity> From the Unity Configuration schematic shown above, you see that the ‘unity’ block has a ‘typeAliases’ and a ‘containers’ segment. The typeAlias element gives a ‘short-name’ for a type. This ‘short-name’ can be used to point to this type any where in the configuration file (web.config in our case, but all this information could be coming from an external xml file as well). The container element holds all the mapping information. This container is referenced through its name attribute in the code and you can have multiple of these container elements in the containers segment. The ‘type’ element in line 10 basically says: ‘When Unity requests to resolve the alias IProduct, return an instance of whatever the short-name of Product points to’. This is the most basic piece of Unity pattern and all of this is accomplished purely through configuration. So, in future you have a change in your model, all you need to do is - implement IProduct on the new model class and - either add a typeAlias for the new type and point the mapTo attribute to the new alias declared - or modify the mapTo attribute of the type element to point to the new alias (as the case may be). Now for the calling code. It’s a good idea to store your unity container details in the Application cache, as this is rarely bound to change and also adds for better performance. The Global.asax.cs file comes for our rescue: 1: protected void Application_Start(object sender, EventArgs e) 2: { 3: // create and populate a new Unity container from configuration 4: IUnityContainer unityContainer = new UnityContainer(); 5: UnityConfigurationSection section = (UnityConfigurationSection)ConfigurationManager.GetSection("unity"); 6: section.Containers["unityContainer"].Configure(unityContainer); 7: Application["UnityContainer"] = unityContainer; 8: } 9:  10: protected void Application_End(object sender, EventArgs e) 11: { 12: Application["UnityContainer"] = null; 13: } All this says is: create an instance of UnityContainer() and read the ‘unity’ section from the configSections segment of the web.config file. Then get the container named ‘unityContainer’ and store it in the Application cache. In my code-behind file, I’ll make use of this UnityContainer to create an instance of the Product type. 1: public partial class _Default : Page 2: { 3: private IUnityContainer unityContainer; 4: protected void Page_Load(object sender, EventArgs e) 5: { 6: unityContainer = Application["UnityContainer"] as IUnityContainer; 7: if (unityContainer == null) 8: { 9: productDetailsLabel.Text = "ERROR: Unity Container not populated in Global.asax.<p />"; 10: } 11: else 12: { 13: IProduct productInstance = unityContainer.Resolve<IProduct>(); 14: productDetailsLabel.Text = productInstance.WriteProductDetails(); 15: } 16: } 17: } Looking the ‘else’ block, I’m asking the unityContainer object to resolve the IProduct type. All this does, is to look at the matching type in the container, read its mapTo attribute value, get the full name from the alias and create an instance of the Product class. Fabulous!! I’ll go more in detail in the next blog. The code for this blog can be found here.

  Read the article

• New Cumulative Updates for SQL Server 2005 & SQL Server 2008 R2

  - by AaronBertrand

  Early this morning, the SQL Server Release Services team pushed out three new cumulative updates for SQL Server. KB #2489375 - SQL Server 2005 SP3 CU #14 (9.00.4317) KB #2489409 - SQL Server 2005 SP4 CU #2 (9.00.5259) KB #2489376 - SQL Server 2008 R2 CU #6 (10.50.1765) There are a lot more fixes in the 2008 R2 update - 43, by my count. In comparison, only 9 fixes for 2005 SP4, and only 2 fixes for 2005 SP3. You can draw your own conclusions from that data, particularly if you are still on SQL Server...(read more)

  Read the article

• Build an iPhone 5 Charging Dock for $1 [DIY Project Video]

  - by Asian Angel

  Are you experiencing frustration since no one has built and released an official charging dock for the iPhone 5 yet? Then this quick little DIY charging dock project may be the perfect solution to your problem and serve as a good ‘hold-over’ until a factory version is released. Build an iPhone 5 dock for $1 [via There I Fixed It - Cheezburger Network] 8 Deadly Commands You Should Never Run on Linux 14 Special Google Searches That Show Instant Answers How To Create a Customized Windows 7 Installation Disc With Integrated Updates

  Read the article

• Node.js Adventure - Host Node.js on Windows Azure Worker Role

  - by Shaun

  In my previous post I demonstrated about how to develop and deploy a Node.js application on Windows Azure Web Site (a.k.a. WAWS). WAWS is a new feature in Windows Azure platform. Since it’s low-cost, and it provides IIS and IISNode components so that we can host our Node.js application though Git, FTP and WebMatrix without any configuration and component installation. But sometimes we need to use the Windows Azure Cloud Service (a.k.a. WACS) and host our Node.js on worker role. Below are some benefits of using worker role. - WAWS leverages IIS and IISNode to host Node.js application, which runs in x86 WOW mode. It reduces the performance comparing with x64 in some cases. - WACS worker role does not need IIS, hence there’s no restriction of IIS, such as 8000 concurrent requests limitation. - WACS provides more flexibility and controls to the developers. For example, we can RDP to the virtual machines of our worker role instances. - WACS provides the service configuration features which can be changed when the role is running. - WACS provides more scaling capability than WAWS. In WAWS we can have at most 3 reserved instances per web site while in WACS we can have up to 20 instances in a subscription. - Since when using WACS worker role we starts the node by ourselves in a process, we can control the input, output and error stream. We can also control the version of Node.js.   Run Node.js in Worker Role Node.js can be started by just having its execution file. This means in Windows Azure, we can have a worker role with the “node.exe” and the Node.js source files, then start it in Run method of the worker role entry class. Let’s create a new windows azure project in Visual Studio and add a new worker role. Since we need our worker role execute the “node.exe” with our application code we need to add the “node.exe” into our project. Right click on the worker role project and add an existing item. By default the Node.js will be installed in the “Program Files\nodejs” folder so we can navigate there and add the “node.exe”. Then we need to create the entry code of Node.js. In WAWS the entry file must be named “server.js”, which is because it’s hosted by IIS and IISNode and IISNode only accept “server.js”. But here as we control everything we can choose any files as the entry code. For example, I created a new JavaScript file named “index.js” in project root. Since we created a C# Windows Azure project we cannot create a JavaScript file from the context menu “Add new item”. We have to create a text file, and then rename it to JavaScript extension. After we added these two files we should set their “Copy to Output Directory” property to “Copy Always”, or “Copy if Newer”. Otherwise they will not be involved in the package when deployed. Let’s paste a very simple Node.js code in the “index.js” as below. As you can see I created a web server listening at port 12345. 1: var http = require("http"); 2: var port = 12345; 3:  4: http.createServer(function (req, res) { 5: res.writeHead(200, { "Content-Type": "text/plain" }); 6: res.end("Hello World\n"); 7: }).listen(port); 8:  9: console.log("Server running at port %d", port); Then we need to start “node.exe” with this file when our worker role was started. This can be done in its Run method. I found the Node.js and entry JavaScript file name, and then create a new process to run it. Our worker role will wait for the process to be exited. If everything is OK once our web server was opened the process will be there listening for incoming requests, and should not be terminated. The code in worker role would be like this. 1: public override void Run() 2: { 3: // This is a sample worker implementation. Replace with your logic. 4: Trace.WriteLine("NodejsHost entry point called", "Information"); 5:  6: // retrieve the node.exe and entry node.js source code file name. 7: var node = Environment.ExpandEnvironmentVariables(@"%RoleRoot%\approot\node.exe"); 8: var js = "index.js"; 9:  10: // prepare the process starting of node.exe 11: var info = new ProcessStartInfo(node, js) 12: { 13: CreateNoWindow = false, 14: ErrorDialog = true, 15: WindowStyle = ProcessWindowStyle.Normal, 16: UseShellExecute = false, 17: WorkingDirectory = Environment.ExpandEnvironmentVariables(@"%RoleRoot%\approot") 18: }; 19: Trace.WriteLine(string.Format("{0} {1}", node, js), "Information"); 20:  21: // start the node.exe with entry code and wait for exit 22: var process = Process.Start(info); 23: process.WaitForExit(); 24: } Then we can run it locally. In the computer emulator UI the worker role started and it executed the Node.js, then Node.js windows appeared. Open the browser to verify the website hosted by our worker role. Next let’s deploy it to azure. But we need some additional steps. First, we need to create an input endpoint. By default there’s no endpoint defined in a worker role. So we will open the role property window in Visual Studio, create a new input TCP endpoint to the port we want our website to use. In this case I will use 80. Even though we created a web server we should add a TCP endpoint of the worker role, since Node.js always listen on TCP instead of HTTP. And then changed the “index.js”, let our web server listen on 80. 1: var http = require("http"); 2: var port = 80; 3:  4: http.createServer(function (req, res) { 5: res.writeHead(200, { "Content-Type": "text/plain" }); 6: res.end("Hello World\n"); 7: }).listen(port); 8:  9: console.log("Server running at port %d", port); Then publish it to Windows Azure. And then in browser we can see our Node.js website was running on WACS worker role. We may encounter an error if we tried to run our Node.js website on 80 port at local emulator. This is because the compute emulator registered 80 and map the 80 endpoint to 81. But our Node.js cannot detect this operation. So when it tried to listen on 80 it will failed since 80 have been used.   Use NPM Modules When we are using WAWS to host Node.js, we can simply install modules we need, and then just publish or upload all files to WAWS. But if we are using WACS worker role, we have to do some extra steps to make the modules work. Assuming that we plan to use “express” in our application. Firstly of all we should download and install this module through NPM command. But after the install finished, they are just in the disk but not included in the worker role project. If we deploy the worker role right now the module will not be packaged and uploaded to azure. Hence we need to add them to the project. On solution explorer window click the “Show all files” button, select the “node_modules” folder and in the context menu select “Include In Project”. But that not enough. We also need to make all files in this module to “Copy always” or “Copy if newer”, so that they can be uploaded to azure with the “node.exe” and “index.js”. This is painful step since there might be many files in a module. So I created a small tool which can update a C# project file, make its all items as “Copy always”. The code is very simple. 1: static void Main(string[] args) 2: { 3: if (args.Length < 1) 4: { 5: Console.WriteLine("Usage: copyallalways [project file]"); 6: return; 7: } 8:  9: var proj = args[0]; 10: File.Copy(proj, string.Format("{0}.bak", proj)); 11:  12: var xml = new XmlDocument(); 13: xml.Load(proj); 14: var nsManager = new XmlNamespaceManager(xml.NameTable); 15: nsManager.AddNamespace("pf", "http://schemas.microsoft.com/developer/msbuild/2003"); 16:  17: // add the output setting to copy always 18: var contentNodes = xml.SelectNodes("//pf:Project/pf:ItemGroup/pf:Content", nsManager); 19: UpdateNodes(contentNodes, xml, nsManager); 20: var noneNodes = xml.SelectNodes("//pf:Project/pf:ItemGroup/pf:None", nsManager); 21: UpdateNodes(noneNodes, xml, nsManager); 22: xml.Save(proj); 23:  24: // remove the namespace attributes 25: var content = xml.InnerXml.Replace("<CopyToOutputDirectory xmlns=\"\">", "<CopyToOutputDirectory>"); 26: xml.LoadXml(content); 27: xml.Save(proj); 28: } 29:  30: static void UpdateNodes(XmlNodeList nodes, XmlDocument xml, XmlNamespaceManager nsManager) 31: { 32: foreach (XmlNode node in nodes) 33: { 34: var copyToOutputDirectoryNode = node.SelectSingleNode("pf:CopyToOutputDirectory", nsManager); 35: if (copyToOutputDirectoryNode == null) 36: { 37: var n = xml.CreateNode(XmlNodeType.Element, "CopyToOutputDirectory", null); 38: n.InnerText = "Always"; 39: node.AppendChild(n); 40: } 41: else 42: { 43: if (string.Compare(copyToOutputDirectoryNode.InnerText, "Always", true) != 0) 44: { 45: copyToOutputDirectoryNode.InnerText = "Always"; 46: } 47: } 48: } 49: } Please be careful when use this tool. I created only for demo so do not use it directly in a production environment. Unload the worker role project, execute this tool with the worker role project file name as the command line argument, it will set all items as “Copy always”. Then reload this worker role project. Now let’s change the “index.js” to use express. 1: var express = require("express"); 2: var app = express(); 3:  4: var port = 80; 5:  6: app.configure(function () { 7: }); 8:  9: app.get("/", function (req, res) { 10: res.send("Hello Node.js!"); 11: }); 12:  13: app.get("/User/:id", function (req, res) { 14: var id = req.params.id; 15: res.json({ 16: "id": id, 17: "name": "user " + id, 18: "company": "IGT" 19: }); 20: }); 21:  22: app.listen(port); Finally let’s publish it and have a look in browser.   Use Windows Azure SQL Database We can use Windows Azure SQL Database (a.k.a. WACD) from Node.js as well on worker role hosting. Since we can control the version of Node.js, here we can use x64 version of “node-sqlserver” now. This is better than if we host Node.js on WAWS since it only support x86. Just install the “node-sqlserver” module from NPM, copy the “sqlserver.node” from “Build\Release” folder to “Lib” folder. Include them in worker role project and run my tool to make them to “Copy always”. Finally update the “index.js” to use WASD. 1: var express = require("express"); 2: var sql = require("node-sqlserver"); 3:  4: var connectionString = "Driver={SQL Server Native Client 10.0};Server=tcp:{SERVER NAME}.database.windows.net,1433;Database={DATABASE NAME};Uid={LOGIN}@{SERVER NAME};Pwd={PASSWORD};Encrypt=yes;Connection Timeout=30;"; 5: var port = 80; 6:  7: var app = express(); 8:  9: app.configure(function () { 10: app.use(express.bodyParser()); 11: }); 12:  13: app.get("/", function (req, res) { 14: sql.open(connectionString, function (err, conn) { 15: if (err) { 16: console.log(err); 17: res.send(500, "Cannot open connection."); 18: } 19: else { 20: conn.queryRaw("SELECT * FROM [Resource]", function (err, results) { 21: if (err) { 22: console.log(err); 23: res.send(500, "Cannot retrieve records."); 24: } 25: else { 26: res.json(results); 27: } 28: }); 29: } 30: }); 31: }); 32:  33: app.get("/text/:key/:culture", function (req, res) { 34: sql.open(connectionString, function (err, conn) { 35: if (err) { 36: console.log(err); 37: res.send(500, "Cannot open connection."); 38: } 39: else { 40: var key = req.params.key; 41: var culture = req.params.culture; 42: var command = "SELECT * FROM [Resource] WHERE [Key] = '" + key + "' AND [Culture] = '" + culture + "'"; 43: conn.queryRaw(command, function (err, results) { 44: if (err) { 45: console.log(err); 46: res.send(500, "Cannot retrieve records."); 47: } 48: else { 49: res.json(results); 50: } 51: }); 52: } 53: }); 54: }); 55:  56: app.get("/sproc/:key/:culture", function (req, res) { 57: sql.open(connectionString, function (err, conn) { 58: if (err) { 59: console.log(err); 60: res.send(500, "Cannot open connection."); 61: } 62: else { 63: var key = req.params.key; 64: var culture = req.params.culture; 65: var command = "EXEC GetItem '" + key + "', '" + culture + "'"; 66: conn.queryRaw(command, function (err, results) { 67: if (err) { 68: console.log(err); 69: res.send(500, "Cannot retrieve records."); 70: } 71: else { 72: res.json(results); 73: } 74: }); 75: } 76: }); 77: }); 78:  79: app.post("/new", function (req, res) { 80: var key = req.body.key; 81: var culture = req.body.culture; 82: var val = req.body.val; 83:  84: sql.open(connectionString, function (err, conn) { 85: if (err) { 86: console.log(err); 87: res.send(500, "Cannot open connection."); 88: } 89: else { 90: var command = "INSERT INTO [Resource] VALUES ('" + key + "', '" + culture + "', N'" + val + "')"; 91: conn.queryRaw(command, function (err, results) { 92: if (err) { 93: console.log(err); 94: res.send(500, "Cannot retrieve records."); 95: } 96: else { 97: res.send(200, "Inserted Successful"); 98: } 99: }); 100: } 101: }); 102: }); 103:  104: app.listen(port); Publish to azure and now we can see our Node.js is working with WASD through x64 version “node-sqlserver”.   Summary In this post I demonstrated how to host our Node.js in Windows Azure Cloud Service worker role. By using worker role we can control the version of Node.js, as well as the entry code. And it’s possible to do some pre jobs before the Node.js application started. It also removed the IIS and IISNode limitation. I personally recommended to use worker role as our Node.js hosting. But there are some problem if you use the approach I mentioned here. The first one is, we need to set all JavaScript files and module files as “Copy always” or “Copy if newer” manually. The second one is, in this way we cannot retrieve the cloud service configuration information. For example, we defined the endpoint in worker role property but we also specified the listening port in Node.js hardcoded. It should be changed that our Node.js can retrieve the endpoint. But I can tell you it won’t be working here. In the next post I will describe another way to execute the “node.exe” and Node.js application, so that we can get the cloud service configuration in Node.js. I will also demonstrate how to use Windows Azure Storage from Node.js by using the Windows Azure Node.js SDK.   Hope this helps, Shaun All documents and related graphics, codes are provided "AS IS" without warranty of any kind. Copyright © Shaun Ziyan Xu. This work is licensed under the Creative Commons License.

  Read the article

• Oracle Linux Training Calendar

  - by Antoinette O'Sullivan

  The Oracle Linux System Administrator Curriculum is designed to provide you with the knowledge and skills necessary to effectively administer an Oracle Linux environment. These classes will help you prepare to install, configure, and manage your enterprise Linux environment as well as prepare you for the Oracle Linux Certification. You can take these courses as a: Live-Virtual event: Following the instructor-led classes from your own desk - no travel required. There is an extensive list of events on the schedule to suit different timezones. See full list on http://oracle.com/education/linux. In-Class event: Travel to an education center to take these classes. Below is a sample of in-class events on the schedule: Unix and Linux Essentials: This 3-day class is for those new to the linux operating system. You learn to manage files & directories from the command line, perform remote connections, file transfers & more.  Location  Date  Delivery Language  Nairobi, Kenya  3 December 2012  English  Riyadh, Saudia Arabia  5 January 2013  English  Cape Town, South Africa  9 January 2013  English  Durban, South Africa  9 January 2013  English  Johannesburg, South Africa  9 January 2013  English  Woodmead, South Africa  15 July 2013  English  Denver, United States  23 January 2013  English  Columbia, United States  2 January 2013  English  East Lansing, United States  9 January 2013  English  Roseville, United States  1 April 2013  English  Morrisville, United States  11 February 2013  English  Jakarta, Indonesia  26 December 2012  English  Kuala Lumpur, Malaysia  29 January 2013  English  Auckland, New Zealand  12 December 2012  English  Makati City, Philippines  14 January 2013  English  Singapore  13 February 2013  English  North Sydney, Australia  4 February 2013  English  Brisbane, Australia  29 April 2013  English  Melbourne, Australia  29 January 2013  English Oracle Linux System Administration: This 5 day course covers a broad range of Oracle Linux system administration tasks, from installing the operating system to preparing the system for Oracle Database. The course also provides an extensive hands-on experience for key system administration tasks. You will gain comprehensive skills in installing, configuring, and managing an Oracle Linux system as well as insight into ULN, Ksplice and UEK.  Location  Date  Delivery Language  Brussels, Belgium  26 November 2012  English  Windhof, Luxembourg  17 December 2012  English  Utrecht, Netherlands  11 February 2013  Dutch  Warsaw, Poland  25 February 2013  Polish  Gabarone, Botswana  22 April 2013  English  Nairobi, Kenya  10 December 2012  English  Johannesburg, South Africa  11 March 2013  English  Belmont, CA, United States  11 February 2013  English  Irvine, CA, United States  25 March 2013  English  Roseville, MN, United States  26 November 2013  English  Irving, TX, United States  14 January 2013  English  Jakarta, Indonesia  3 December 2012  English  Singapore  26 November 2012  English  Canberra, Australia  21 January 2013  English  Sydney, Australia  21 January 2013  English  Melbourne, Australia  11 February 2013  English To test your Oracle Linux System Administration skills, take the Oracle Linux 6 Implementation Essentials Certification Exam. For more information on the Oracle Linux Curriculum or to express interest in additional events, go to http://oracle.com/education/linux.

  Read the article

• Ubuntu 14.04 aura pour nom « Trusty Tahr », Mark Shuttleworth s'en prend aux détracteurs de Mir

  Ubuntu 14.04 aura pour nom « Trusty Tahr » Mark Shuttleworth s'en prend aux détracteurs de Mir qui attaquent le serveur d'affichage pour des raisons purement politiquesPas de repos pour Canonical. Moins d'une semaine après la sortie grand public d'Ubuntu 13.10 alias Saucy Salamander, la société se penche déjà sur son successeur Ubuntu 14.04.Mark Shuttleworth, fondateur de Canonical, a publié un billet de blog un jour après la publication d'Ubuntu 13.10, pour révéler le nom et les choix de conception...

  Read the article

• SSH new connection begins to hang (not reject or terminate) after a day or so on Ubuntu 13.04 server

  - by kross

  Recently we upgraded the server from 12.04 LTS server to 13.04. All was well, including after a reboot. With all packages updated we began to see a strange issue, ssh works for a day or so (unclear on timing) then a later request for SSH hangs (cannot ctrl+c, nothing). It is up and serving webserver traffic etc. Port 22 is open (ips etc altered slightly for posting): nmap -T4 -A x.acme.com Starting Nmap 6.40 ( http://nmap.org ) at 2013-09-12 16:01 CDT Nmap scan report for x.acme.com (69.137.56.18) Host is up (0.026s latency). rDNS record for 69.137.56.18: c-69-137-56-18.hsd1.tn.provider.net Not shown: 998 filtered ports PORT STATE SERVICE VERSION 22/tcp open ssh OpenSSH 6.1p1 Debian 4 (protocol 2.0) | ssh-hostkey: 1024 54:d3:e3:38:44:f4:20:a4:e7:42:49:d0:a7:f1:3e:21 (DSA) | 2048 dc:21:77:3b:f4:4e:74:d0:87:33:14:40:04:68:33:a6 (RSA) |_256 45:69:10:79:5a:9f:0b:f0:66:15:39:87:b9:a1:37:f7 (ECDSA) 80/tcp open http Jetty 7.6.2.v20120308 | http-title: Log in as a Bamboo user - Atlassian Bamboo |_Requested resource was http://x.acme.com/userlogin!default.action;jsessionid=19v135zn8cl1tgso28fse4d50?os_destination=%2Fstart.action Service Info: OS: Linux; CPE: cpe:/o:linux:linux_kernel Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 12.89 seconds Here is the ssh -vvv: ssh -vvv x.acme.com OpenSSH_5.9p1, OpenSSL 0.9.8x 10 May 2012 debug1: Reading configuration data /Users/tfergeson/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to x.acme.com [69.137.56.18] port 22. debug1: Connection established. debug3: Incorrect RSA1 identifier debug3: Could not load "/Users/tfergeson/.ssh/id_rsa" as a RSA1 public key debug1: identity file /Users/tfergeson/.ssh/id_rsa type 1 debug1: identity file /Users/tfergeson/.ssh/id_rsa-cert type -1 debug1: identity file /Users/tfergeson/.ssh/id_dsa type -1 debug1: identity file /Users/tfergeson/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.1p1 Debian-4 debug1: match: OpenSSH_6.1p1 Debian-4 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug2: fd 3 setting O_NONBLOCK debug3: load_hostkeys: loading entries for host "x.acme.com" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:10 debug3: load_hostkeys: loaded 1 keys debug3: order_hostkeyalgs: prefer hostkeyalgs: [email protected],[email protected],ssh-rsa debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: [email protected],[email protected],ssh-rsa,[email protected],[email protected],ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-256-96,hmac-sha2-512,hmac-sha2-512-96,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: ecdh-sha2-nistp256,ecdh-sha2-nistp384,ecdh-sha2-nistp521,diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss,ecdsa-sha2-nistp256 debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-sha2-256,hmac-sha2-512,hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 130/256 debug2: bits set: 503/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA dc:21:77:3b:f4:4e:74:d0:87:33:14:40:04:68:33:a6 debug3: load_hostkeys: loading entries for host "x.acme.com" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:10 debug3: load_hostkeys: loaded 1 keys debug3: load_hostkeys: loading entries for host "69.137.56.18" from file "/Users/tfergeson/.ssh/known_hosts" debug3: load_hostkeys: found key type RSA in file /Users/tfergeson/.ssh/known_hosts:6 debug3: load_hostkeys: loaded 1 keys debug1: Host 'x.acme.com' is known and matches the RSA host key. debug1: Found key in /Users/tfergeson/.ssh/known_hosts:10 debug2: bits set: 493/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /Users/tfergeson/.ssh/id_rsa (0x7ff189c1d7d0) debug2: key: /Users/tfergeson/.ssh/id_dsa (0x0) debug1: Authentications that can continue: publickey debug3: start over, passed a different list publickey debug3: preferred publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/tfergeson/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: fp 3c:e5:29:6c:9d:27:d1:7d:e8:09:a2:e8:8e:6e:af:6f debug3: sign_and_send_pubkey: RSA 3c:e5:29:6c:9d:27:d1:7d:e8:09:a2:e8:8e:6e:af:6f debug1: read PEM private key done: type RSA debug1: Authentication succeeded (publickey). Authenticated to x.acme.com ([69.137.56.18]:22). debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: fd 3 setting TCP_NODELAY debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug3: Ignored env ATLAS_OPTS debug3: Ignored env rvm_bin_path debug3: Ignored env TERM_PROGRAM debug3: Ignored env GEM_HOME debug3: Ignored env SHELL debug3: Ignored env TERM debug3: Ignored env CLICOLOR debug3: Ignored env IRBRC debug3: Ignored env TMPDIR debug3: Ignored env Apple_PubSub_Socket_Render debug3: Ignored env TERM_PROGRAM_VERSION debug3: Ignored env MY_RUBY_HOME debug3: Ignored env TERM_SESSION_ID debug3: Ignored env USER debug3: Ignored env COMMAND_MODE debug3: Ignored env rvm_path debug3: Ignored env COM_GOOGLE_CHROME_FRAMEWORK_SERVICE_PROCESS/USERS/tfergeson/LIBRARY/APPLICATION_SUPPORT/GOOGLE/CHROME_SOCKET debug3: Ignored env JPDA_ADDRESS debug3: Ignored env APDK_HOME debug3: Ignored env SSH_AUTH_SOCK debug3: Ignored env Apple_Ubiquity_Message debug3: Ignored env __CF_USER_TEXT_ENCODING debug3: Ignored env rvm_sticky_flag debug3: Ignored env MAVEN_OPTS debug3: Ignored env LSCOLORS debug3: Ignored env rvm_prefix debug3: Ignored env PATH debug3: Ignored env PWD debug3: Ignored env JAVA_HOME debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env JPDA_TRANSPORT debug3: Ignored env rvm_version debug3: Ignored env M2_HOME debug3: Ignored env HOME debug3: Ignored env SHLVL debug3: Ignored env rvm_ruby_string debug3: Ignored env LOGNAME debug3: Ignored env M2_REPO debug3: Ignored env GEM_PATH debug3: Ignored env AWS_RDS_HOME debug3: Ignored env rvm_delete_flag debug3: Ignored env EC2_PRIVATE_KEY debug3: Ignored env RUBY_VERSION debug3: Ignored env SECURITYSESSIONID debug3: Ignored env EC2_CERT debug3: Ignored env _ debug2: channel 0: request shell confirm 1 debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 I can hard reboot (only mac monitors at that location) and it will again be accessible. This now happens every single time. It is imperative that I get it sorted. The strange thing is that it behaves initially then starts to hang after several hours. I perused logs previously and nothing stood out. From the auth.log, I can see that it has allowed me in, but still I get nothing back on the client side: Sep 20 12:47:50 cbear sshd[25376]: Accepted publickey for tfergeson from 10.1.10.14 port 54631 ssh2 Sep 20 12:47:50 cbear sshd[25376]: pam_unix(sshd:session): session opened for user tfergeson by (uid=0) UPDATES: Still occurring even after setting UseDNS no and commenting out #session optional pam_mail.so standard noenv This does not appear to be a network/dns related issue, as all services running on the machine are as responsive and accessible as ever, with the exception of sshd. Any thoughts on where to start?

  Read the article

• MVC 3 AdditionalMetadata Attribute with ViewBag to Render Dynamic UI

  - by Steve Michelotti

  A few months ago I blogged about using Model metadata to render a dynamic UI in MVC 2. The scenario in the post was that we might have a view model where the questions are conditionally displayed and therefore a dynamic UI is needed. To recap the previous post, the solution was to use a custom attribute called [QuestionId] in conjunction with an “ApplicableQuestions” collection to identify whether each question should be displayed. This allowed me to have a view model that looked like this: 1: [UIHint("ScalarQuestion")] 2: [DisplayName("First Name")] 3: [QuestionId("NB0021")] 4: public string FirstName { get; set; } 5: 6: [UIHint("ScalarQuestion")] 7: [DisplayName("Last Name")] 8: [QuestionId("NB0022")] 9: public string LastName { get; set; } 10: 11: [UIHint("ScalarQuestion")] 12: [QuestionId("NB0023")] 13: public int Age { get; set; } 14: 15: public IEnumerable<string> ApplicableQuestions { get; set; } At the same time, I was able to avoid repetitive IF statements for every single question in my view: 1: <%: Html.EditorFor(m => m.FirstName, new { applicableQuestions = Model.ApplicableQuestions })%> 2: <%: Html.EditorFor(m => m.LastName, new { applicableQuestions = Model.ApplicableQuestions })%> 3: <%: Html.EditorFor(m => m.Age, new { applicableQuestions = Model.ApplicableQuestions })%> by creating an Editor Template called “ScalarQuestion” that encapsulated the IF statement: 1: <%@ Control Language="C#" Inherits="System.Web.Mvc.ViewUserControl" %> 2: <%@ Import Namespace="DynamicQuestions.Models" %> 3: <%@ Import Namespace="System.Linq" %> 4: <% 5: var applicableQuestions = this.ViewData["applicableQuestions"] as IEnumerable<string>; 6: var questionAttr = this.ViewData.ModelMetadata.ContainerType.GetProperty(this.ViewData.ModelMetadata.PropertyName).GetCustomAttributes(typeof(QuestionIdAttribute), true) as QuestionIdAttribute[]; 7: string questionId = null; 8: if (questionAttr.Length > 0) 9: { 10: questionId = questionAttr[0].Id; 11: } 12: if (questionId != null && applicableQuestions.Contains(questionId)) { %> 13: <div> 14: <%: Html.Label("") %> 15: <%: Html.TextBox("", this.Model)%> 16: </div> 17: <% } %> You might want to go back and read the full post in order to get the full context. MVC 3 offers a couple of new features that make this scenario more elegant to implement. The first step is to use the new [AdditionalMetadata] attribute which, so far, appears to be an under appreciated new feature of MVC 3. With this attribute, I don’t need my custom [QuestionId] attribute anymore - now I can just write my view model like this: 1: [UIHint("ScalarQuestion")] 2: [DisplayName("First Name")] 3: [AdditionalMetadata("QuestionId", "NB0021")] 4: public string FirstName { get; set; } 5:   6: [UIHint("ScalarQuestion")] 7: [DisplayName("Last Name")] 8: [AdditionalMetadata("QuestionId", "NB0022")] 9: public string LastName { get; set; } 10:   11: [UIHint("ScalarQuestion")] 12: [AdditionalMetadata("QuestionId", "NB0023")] 13: public int Age { get; set; } Thus far, the documentation seems to be pretty sparse on the AdditionalMetadata attribute. It’s buried in the Other New Features section of the MVC 3 home page and, after showing the attribute on a view model property, it just says, “This metadata is made available to any display or editor template when a product view model is rendered. It is up to you to interpret the metadata information.” But what exactly does it look like for me to “interpret the metadata information”? Well, it turns out it makes the view much easier to work with. Here is the re-implemented ScalarQuestion template updated for MVC 3 and Razor: 1: @{ 2: object questionId; 3: ViewData.ModelMetadata.AdditionalValues.TryGetValue("QuestionId", out questionId); 4: if (ViewBag.applicableQuestions.Contains((string)questionId)) { 5: <div> 6: @Html.LabelFor(m => m) 7: @Html.TextBoxFor(m => m) 8: </div> 9: } 10: } So we’ve gone from 17 lines of code (in the MVC 2 version) to about 7-8 lines of code here. The first thing to notice is that in MVC 3 we now have a property called “AdditionalValues” that hangs off of the ModelMetadata property. This is automatically populated by any [AdditionalMetadata] attributes on the property. There is no more need for me to explicitly write Reflection code to GetCustomAttributes() and then check to see if those attributes were present. I can just call TryGetValue() on the dictionary to see if they were present. Secondly, the “applicableQuestions” anonymous type that I passed in from the calling view – in MVC 3 I now have a dynamic ViewBag property where I can just “dot into” the applicableQuestions with a nicer syntax than dictionary square bracket syntax. And there’s no problems calling the Contains() method on this dynamic object because at runtime the DLR has resolved that it is a generic List<string>. At this point you might be saying that, yes the view got much nicer than the MVC 2 version, but my view model got slightly worse.  In the previous version I had a nice [QuestionId] attribute but now, with the [AdditionalMetadata] attribute, I have to type the string “QuestionId” for every single property and hope that I don’t make a typo. Well, the good news is that it’s easy to create your own attributes that can participate in the metadata’s additional values. The key is that the attribute must implement that IMetadataAware interface and populate the AdditionalValues dictionary in the OnMetadataCreated() method: 1: public class QuestionIdAttribute : Attribute, IMetadataAware 2: { 3: public string Id { get; set; } 4:   5: public QuestionIdAttribute(string id) 6: { 7: this.Id = id; 8: } 9:   10: public void OnMetadataCreated(ModelMetadata metadata) 11: { 12: metadata.AdditionalValues["QuestionId"] = this.Id; 13: } 14: } This now allows me to encapuslate my “QuestionId” string in just one place and get back to my original attribute which can be used like this: [QuestionId(“NB0021”)]. The [AdditionalMetadata] attribute is a powerful and under-appreciated new feature of MVC 3. Combined with the dynamic ViewBag property, you can do some really interesting things with your applications with less code and ceremony.

  Read the article

• How Does a Touch Screen Phone Work? [Chart]

  - by Asian Angel

  There are three types of touch screen technologies available in today’s touch screen phones: resistive, capacitive, and infra-red. Learn about the different benefits and capabilities of each and make a more informed decision about your next mobile phone selection with this helpful chart. How Does a Touch Screen Phone Work? [via GraphJam] 8 Deadly Commands You Should Never Run on Linux 14 Special Google Searches That Show Instant Answers How To Create a Customized Windows 7 Installation Disc With Integrated Updates

  Read the article

• Virtual Box - How to open a .VDI Virtual Machine

  - by [email protected]

   How to open a .VDI Virtual MachineSometimes someone share with us one Virtual machine with extension .VDI, after that we can wonder how and what with?Well the answer is... It is a VirtualBox - Virtual Machine. If you have not downloaded it you can do this easily just follow this post.http://listeningoracle.blogspot.com/2010/04/que-es-virtualbox.htmlor http://oracleoforacle.wordpress.com/2010/04/14/ques-es-virtualbox/Ok, Now with VirtualBox Installed open it and proceed with the following:1. Open the Virtual File Manager. 2. Click on Actions ? Add and select the .VDI file Click "Ok"3. Now we can register the new Virtual Machine - Click New, and Click Next4. Write down a Name for the virtual Machine a proceed to select a Operating System and Version. (In this case it is a Linux (Oracle Enterprise Linux or RedHat)Click Next5. Select the memory amount base for the Virtual Machine (Minimal 1280 for our case) - Click Next6. Select the Disk 11GR2_OEL5_32GB.vdi it was added in the virtual media manager in the step 2. Dont forget let selected Boot hard Disk (Primary Master) . Given it is the only disk assigned to the virtual machine.Click Next7. Click Finish8. This step is important. Once you have click on the settings Button.9. On General option click the advanced settings. Here you must change the default directory to save your Snapshots; my recommendation set it to the same directory where the .Vdi file is. Otherwise you can have the same Virtual Machine and its snapshots in different paths.10. Now Click on System, and proceed to assign the correct memory (If you did not before) Note: Enable "Enable IO APIC" if you are planning to assign more than one CPU to the Virtual Machine.Define the processors for the Virtual machine. If you processor is dual core choose 211. Select the video memory amount you want to assign to the Virtual Machine 12. Associated more storage disk to the Virtual machine, if you have more VDI files. (Not our case)The disk must be selected as IDE Primary Master. 13. Well you can verify the other options, but with these changes you will be able to start the VM.Note: Sometime the VM owner may share some instructions, if so follow his instructions.14. Finally Start the Virtual Machine (Click > Start)

  Read the article

• SQL SERVER – Challenge – Puzzle – Usage of FAST Hint

  - by pinaldave

  I was recently working with various SQL Server Hints. After working for a day on various hints, I realize that for one hint, I am not able to come up with good example. The hint is FAST. Let us look at the definition of the FAST hint from the Book On-Line. FAST number_rows Specifies that the query is optimized for fast retrieval of the first number_rows. This is a nonnegative integer. After the first number_rows are returned, the query continues execution and produces its full result set. Now the question is in what condition this hint can be useful. I have tried so many different combination, I have found this hint does not make much performance difference, infect I did not notice any change in time taken to load the resultset. I noticed that this hint does not change number of the page read to return result. Now when there is difference in performance is expected because if you read the what FAST hint does is that it only returns first few results FAST – which does not mean there will be difference in performance. I also understand that this hint gives the guidance/suggestions/hint to query optimizer that there are only 100 rows are in expected resultset. This tricking the optimizer to think there are only 100 rows and which (may) lead to render different execution plan than the one which it would have taken in normal case (without hint). Again, not necessarily, this will happen always. Now if you read above discussion, you will find that basic understanding of the hint is very clear to me but I still feel that I am missing something. Here are my questions: 1) In what condition this hint can be useful? What is the case, when someone want to see first few rows early because my experience suggests that when first few rows are rendered remaining rows are rendered as well. 2) Is there any way application can retrieve the fast fetched rows from SQL Server? 3) Do you use this hint in your application? Why? When? and How? Here are few examples I have attempted during the my experiment and found there is no difference in execution plan except its estimated number of rows are different leading optimizer think that the cost is less but in reality that is not the case. USE AdventureWorks GO SET STATISTICS IO ON SET STATISTICS TIME ON GO --------------------------------------------- -- Table Scan with Fast Hint SELECT * FROM Sales.SalesOrderDetail GO SELECT * FROM Sales.SalesOrderDetail OPTION (FAST 100) GO --------------------------------------------- -- Table Scan with Where on Index Key SELECT * FROM Sales.SalesOrderDetail WHERE OrderQty = 14 GO SELECT * FROM Sales.SalesOrderDetail WHERE OrderQty = 14 OPTION (FAST 100) GO --------------------------------------------- -- Table Scan with Where on Index Key SELECT * FROM Sales.SalesOrderDetail WHERE SalesOrderDetailID < 1000 GO SELECT * FROM Sales.SalesOrderDetail WHERE SalesOrderDetailID < 1000 OPTION (FAST 100) GO Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Puzzle, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Daily tech links for .net and related technologies - Mar 23-25, 2010

  - by SanjeevAgarwal

  Daily tech links for .net and related technologies - Mar 23-25, 2010 Web Development Introducing Browsers Providers in ASP.NET 4 - osbornm ASP.NET 4.0 Part 14, More Control Over Session State - hmobius Editable MVC Routes (Apache Style) - nberardi ASP.NET Performance Framework - karlseguin Web Design Techniques for Squeezing Images for All They’re Worth - Walter 12 Useful and Free Downloadable Web Design Books - SpeckyBoy Getting Started with Xcode IDE for iPhone Development - keyvan Grid Accordion...(read more)

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >