Search Results

Search found 23762 results on 951 pages for 'network speed'.

Page 47/951 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

  • Arch Linux: eth0 no carrier - network fails at boot

    - by user905686
    The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

    Read the article

  • Ubuntu 10.04 network manager issues

    - by Shark
    I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

    Read the article

  • How to auto syncronize files with network drive on Windows XP?

    - by stephenmm
    Windows XP: I would like to auto synchronize files between a a local drive and a network drive. I am aware of Windows Briefcase but it is very slow and I have to tell it to synchronize. I really like the way Dropbox does there synchronization as it is almost instantaneous. It is very impressive. I would just use Dropbox but I cannot install it on the remote machine. Is there some tool or script I can create that will watch a particular folder for any changes and then sync those changes to the networked drive automatically and nearly instantaneously? CLARIFICATION: I would like this tool/script to to be a daemon that starts when windows starts and continually monitors a folder for any changes to its contents. Once it observes changes in the source or the destination it synchronizes the files that changed (Very similar to the way Dropbox works). I have a good idea about how I would do this in a Perl script and if a tool does not exist that does this I will write it myself in Perl. If someone has already done this can they share the script?

    Read the article

  • ubuntu 12.04 kvm virtual server network setup, can't get the machine to be connectable

    - by xyious
    I have worked on my Ubuntu Server host for weeks now and I just can not manage to get the virtual machines into the network.... here's what I need to do: I need to be able to create virtual machines that have IP addresses that can be reached from the outside (192.168 network). I need to be able to connect to the virtual machines through ssh, ftp, http and preferably https, anything else doesn't matter that much. So far everything seems simple enough and I have a lot of leeway in terms of IP address range and server/client configuration. I have the option of taking part of a /24 net as most IPs aren't used, and if it's absolutely necessary I have the option of creating a new /24 subnet. Also have the option of reformatting and reinstalling OS on the host and recreating the virtual machines as nothing has been done other than trying to get virtual machines to work. I would prefer if the virtual machines were just part of the normal network which would be 192.168.5.0/24. The host machine has 2 network cards so I don't even necessarily need the Host to be connectable in the same /24 network. I have tried (I think) just about everything from about 5 different tutorials on bridging (giving br0 the same IP that eth0 used to have (Host is able to connect to VM and vice versa, VM doesn't have outside network access), having eth0 set up like it always was and having br0 have a different IP (same as above), NAT with port forwarding (which I would have preferred not to use but will if it works), turning off one of the hosts network cards and just using one of them, different subnets.... etc. I do know my way around iptables fairly well.... Host is 64bit Ubuntu Server 12.04, using libvirt/kvm. edits: Local network is 192.168.5.0/24, host has static ip 192.168.5.254, GW .5.1 which is also nameserver. We have a second Local network at 192.168.10.0/24 with .10.1 GW, but both hosts and VMs were supposed to go into the .5 subnet. The .10 subnet isn't required, but it wouldn't be horrible if the Host were only accessible in the .10 subnet.

    Read the article

  • Share a Printer on Your Network from Vista or XP to Windows 7

    - by Mysticgeek
    The other day we looked at sharing a printer between Windows 7 machines, but you may only have one Windows 7 machine and the printer is connected to a Vista or XP computer. Today we show you how to share a printer from either Vista or XP to Windows 7. We previously showed you how to share files and printers between Windows 7 and XP. But what if you have a printer connected to an XP or Vista machine in another room, and you want to print to it from Windows 7? This guide will walk you through the process. Note: In these examples we’re using 32-bit versions of Windows 7, Vista, and XP on a basic home network. We are using an HP PSC 1500 printer, but keep in mind every printer is different so finding and installing the correct drivers will vary. Share a Printer from Vista To share the printer on a Vista machine click on Start and enter printers into the search box and hit Enter. Right-click on the printer you want to share and select Sharing from the context menu. Now in Printer Properties, select the Sharing tab, mark the box next to Share this printer, and give the printer a name. Make sure the name is something simple with no spaces then click Ok. Share a Printer from XP To share a printer from XP click on Start then select Printers and Faxes. In the Printers and Faxes window right-click on the printer to share and select Sharing. In the Printer Properties window select the Sharing tab and the radio button next to Share this printer and give it a short name with no spaces then click Ok. Add Printer to Windows 7 Now that we have the printer on Vista or XP set up to be shared, it’s time to add it to Windows 7. Open the Start Menu and click on Devices and Printers. In Devices and Printers click on Add a printer. Next click on Add a network, wireless or Bluetooth printer. Windows 7 will search for the printer on your network and once its been found click Next. The printer has been successfully added…click Next. Now you can set it as the default printer and send a test page to verify everything works. If everything is successful, close out of the add printer screens and you should be good to go.   Alternate Method If the method above doesn’t work, you’ll can try the following for either XP or Vista. In our example, when trying to add the printer connected to our XP machine, it wasn’t recognized automatically. If you’re search pulls up nothing then click on The printer that I want isn’t listed. In the Add Printer window under Find a printer by name or TCP/IP address click the radio button next to Select a shared printer by name. You can either type in the path to the printer or click on Browse to find it. In this instance we decided to browse to it and notice we have 5 computers found on the network. We want to be able to print to the XPMCE computer so we double-click on that. Type in the username and password for that computer… Now we see the printer and can select it. The path to the printer is put into the Select a shared printer by name field. Wait while Windows connects to the printer and installs it… It’s successfully added…click Next. Now you can set it as the default printer or not and print a test page to make sure everything works successfully. Now when we go back to Devices and Printers under Printers and Faxes, we see the HP printer on XPMCE. Conclusion Sharing a printer from one machine to another can sometimes be tricky, but the method we used here in our setup worked well. Since the printer we used is fairly new, there wasn’t a problem with locating any drivers for it. Windows 7 includes a lot of device drivers already so you may be surprised on what it’s able to install. Your results may vary depending on your type of printer, Windows version, and network setup. This should get you started configuring the machines on your network—hopefully with good results.  If you you have two Windows 7 computers, then sharing a printer or files is easy through the Homegroup feature. You can also share a printer between Windows 7 machines on the same network but not Homegroup. Similar Articles Productive Geek Tips Share a Printer Between Windows 7 Machines Not in the Same HomegroupShare Files and Printers between Windows 7 and XPHow To Share Files and Printers Between Windows 7 and VistaEnable Mapping to \HostnameC$ Share on Windows 7 or VistaUse the Homegroup Feature in Windows 7 to Share Printers and Files TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • Share a Printer on Your Network from Vista or XP to Windows 7

    - by Mysticgeek
    The other day we looked at sharing a printer between Windows 7 machines, but you may only have one Windows 7 machine and the printer is connected to a Vista or XP computer. Today we show you how to share a printer from either Vista or XP to Windows 7. We previously showed you how to share files and printers between Windows 7 and XP. But what if you have a printer connected to an XP or Vista machine in another room, and you want to print to it from Windows 7? This guide will walk you through the process. Note: In these examples we’re using 32-bit versions of Windows 7, Vista, and XP on a basic home network. We are using an HP PSC 1500 printer, but keep in mind every printer is different so finding and installing the correct drivers will vary. Share a Printer from Vista To share the printer on a Vista machine click on Start and enter printers into the search box and hit Enter. Right-click on the printer you want to share and select Sharing from the context menu. Now in Printer Properties, select the Sharing tab, mark the box next to Share this printer, and give the printer a name. Make sure the name is something simple with no spaces then click Ok. Share a Printer from XP To share a printer from XP click on Start then select Printers and Faxes. In the Printers and Faxes window right-click on the printer to share and select Sharing. In the Printer Properties window select the Sharing tab and the radio button next to Share this printer and give it a short name with no spaces then click Ok. Add Printer to Windows 7 Now that we have the printer on Vista or XP set up to be shared, it’s time to add it to Windows 7. Open the Start Menu and click on Devices and Printers. In Devices and Printers click on Add a printer. Next click on Add a network, wireless or Bluetooth printer. Windows 7 will search for the printer on your network and once its been found click Next. The printer has been successfully added…click Next. Now you can set it as the default printer and send a test page to verify everything works. If everything is successful, close out of the add printer screens and you should be good to go.   Alternate Method If the method above doesn’t work, you’ll can try the following for either XP or Vista. In our example, when trying to add the printer connected to our XP machine, it wasn’t recognized automatically. If you’re search pulls up nothing then click on The printer that I want isn’t listed. In the Add Printer window under Find a printer by name or TCP/IP address click the radio button next to Select a shared printer by name. You can either type in the path to the printer or click on Browse to find it. In this instance we decided to browse to it and notice we have 5 computers found on the network. We want to be able to print to the XPMCE computer so we double-click on that. Type in the username and password for that computer… Now we see the printer and can select it. The path to the printer is put into the Select a shared printer by name field. Wait while Windows connects to the printer and installs it… It’s successfully added…click Next. Now you can set it as the default printer or not and print a test page to make sure everything works successfully. Now when we go back to Devices and Printers under Printers and Faxes, we see the HP printer on XPMCE. Conclusion Sharing a printer from one machine to another can sometimes be tricky, but the method we used here in our setup worked well. Since the printer we used is fairly new, there wasn’t a problem with locating any drivers for it. Windows 7 includes a lot of device drivers already so you may be surprised on what it’s able to install. Your results may vary depending on your type of printer, Windows version, and network setup. This should get you started configuring the machines on your network—hopefully with good results.  If you you have two Windows 7 computers, then sharing a printer or files is easy through the Homegroup feature. You can also share a printer between Windows 7 machines on the same network but not Homegroup. Similar Articles Productive Geek Tips Share a Printer Between Windows 7 Machines Not in the Same HomegroupShare Files and Printers between Windows 7 and XPHow To Share Files and Printers Between Windows 7 and VistaEnable Mapping to \HostnameC$ Share on Windows 7 or VistaUse the Homegroup Feature in Windows 7 to Share Printers and Files TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • Find only physical network adapters with WMI Win32_NetworkAdapter class

    - by Mladen Prajdic
    WMI is Windows Management Instrumentation infrastructure for managing data and machines. We can access it by using WQL (WMI querying language or SQL for WMI). One thing to remember from the WQL link is that it doesn't support ORDER BY. This means that when you do SELECT * FROM wmiObject, the returned order of the objects is not guaranteed. It can return adapters in different order based on logged-in user, permissions of that user, etc… This is not documented anywhere that I've looked and is derived just from my observations. To get network adapters we have to query the Win32_NetworkAdapter class. This returns us all network adapters that windows detect, real and virtual ones, however it only supplies IPv4 data. I've tried various methods of combining properties that are common on all systems since Windows XP. The first thing to do to remove all virtual adapters (like tunneling, WAN miniports, etc…) created by Microsoft. We do this by adding WHERE Manufacturer!='Microsoft' to our WMI query. This greatly narrows the number of adapters we have to work with. Just on my machine it went from 20 adapters to 5. What was left were one real physical Realtek LAN adapter, 2 virtual adapters installed by VMware and 2 virtual adapters installed by VirtualBox. If you read the Win32_NetworkAdapter help page you'd notice that there's an AdapterType that enumerates various adapter types like LAN or Wireless and AdapterTypeID that gives you the same information as AdapterType only in integer form. The dirty little secret is that these 2 properties don't work. They are both hardcoded, AdapterTypeID to "0" and AdapterType to "Ethernet 802.3". The only exceptions I've seen so far are adapters that have no values at all for the two properties, "RAS Async Adapter" that has values of AdapterType = "Wide Area Network" and AdapterTypeID = "3" and various tunneling adapters that have values of AdapterType = "Tunnel" and AdapterTypeID = "15". In the help docs there isn't even a value for 15. So this property was of no help. Next property to give hope is NetConnectionId. This is the name of the network connection as it appears in the Control Panel -> Network Connections. Problem is this value is also localized into various languages and can have different names for different connection. So both of these properties don't help and we haven't even started talking about eliminating virtual adapters. Same as the previous one this property was also of no help. Next two properties I checked were ConfigManagerErrorCode and NetConnectionStatus in hopes of finding disabled and disconnected adapters. If an adapter is enabled but disconnected the ConfigManagerErrorCode = 0 with different NetConnectionStatus. If the adapter is disabled it reports ConfigManagerErrorCode = 22. This looked like a win by using (ConfigManagerErrorCode=0 or ConfigManagerErrorCode=22) in our condition. This way we get enabled (connected and disconnected adapters). Problem with all of the above properties is that none of them filter out the virtual adapters installed by virtualization software like VMware and VirtualBox. The last property to give hope is PNPDeviceID. There's an interesting observation about physical and virtual adapters with this property. Every virtual adapter PNPDeviceID starts with "ROOT\". Even VMware and VirtualBox ones. There were some really, really old physical adapters that had PNPDeviceID starting with "ROOT\" but those were in pre win XP era AFAIK. Since my minimum system to check was Windows XP SP2 I didn't have to worry about those. The only virtual adapter I've seen to not have PNPDeviceID start with "ROOT\" is the RAS Async Adapter for Wide Area Network. But because it is made by Microsoft we've eliminated it with the first condition for the manufacturer. Using the PNPDeviceID has so far proven to be really effective and I've tested it on over 20 different computers of various configurations from Windows XP laptops with wireless and bluetooth cards to virtualized Windows 2008 R2 servers. So far it always worked as expected. I will appreciate you letting me know if you find a configuration where it doesn't work. Let's see some C# code how to do this: ManagementObjectSearcher mos = null;// WHERE Manufacturer!='Microsoft' removes all of the // Microsoft provided virtual adapters like tunneling, miniports, and Wide Area Network adapters.mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft'");// Trying the ConfigManagerErrorCode and NetConnectionStatus variations // proved to still not be enough and it returns adapters installed by // the virtualization software like VMWare and VirtualBox// ConfigManagerErrorCode = 0 -> Device is working properly. This covers enabled and/or disconnected devices// ConfigManagerErrorCode = 22 AND NetConnectionStatus = 0 -> Device is disabled and Disconnected. // Some virtual devices report ConfigManagerErrorCode = 22 (disabled) and some other NetConnectionStatus than 0mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft' AND (ConfigManagerErrorCode = 0 OR (ConfigManagerErrorCode = 22 AND NetConnectionStatus = 0))");// Final solution with filtering on the Manufacturer and PNPDeviceID not starting with "ROOT\"// Physical devices have PNPDeviceID starting with "PCI\" or something else besides "ROOT\"mos = new ManagementObjectSearcher(@"SELECT * FROM Win32_NetworkAdapter WHERE Manufacturer != 'Microsoft' AND NOT PNPDeviceID LIKE 'ROOT\\%'");// Get the physical adapters and sort them by their index. // This is needed because they're not sorted by defaultIList<ManagementObject> managementObjectList = mos.Get() .Cast<ManagementObject>() .OrderBy(p => Convert.ToUInt32(p.Properties["Index"].Value)) .ToList();// Let's just show all the properties for all physical adapters.foreach (ManagementObject mo in managementObjectList){ foreach (PropertyData pd in mo.Properties) Console.WriteLine(pd.Name + ": " + (pd.Value ?? "N/A"));}   That's it. Hope this helps you in some way.

    Read the article

  • networking disabled

    - by Parimal
    hi i have internet working but the network manager applet in the ubuntu 10.10 says that it is disabled and i am not able to enable it however i have previously forced the ip address which i am still getting in ifconfig but in wired section of network connections there is no such interface as eth0 where can i see these settings and how can i enable the etwork manager applet in the title bar thanks in advance

    Read the article

  • Strategies for very fast delivery of webpages.

    - by Cherian
    I run a website Cucumbertown with an initial pay load of nearly 9KB zipped. All my js is delayed loaded with requirejs and modernizer is the only exception. Now all my webpages are Nginx cached and only 10-15% hits go to the backend proxy. And the cache is invalidated by logged in users as proxy_cache_bypass. So for an anonymous user its nearly always a cache hit. I have some basic OS tuning with default via ip dev eth0 initcwnd 15 net.ipv4.tcp_slow_start_after_idle 0 Despite an all cache & large initcwnd my pages still take 2.5 – 3 seconds. I have a yslow score of And page speed at Are there strategies that can help deliver webpages even faster than this? Deliver pages at 1+ second time for 10KB payload? Notes: My servers run of a fairly good data center from Linode at Fremont.

    Read the article

  • Realtek RTL8111/8168B wired network doesn't work anymore

    - by Radar4002
    This sounds like it's a common problem upgrading 11.04, but I am having trouble finding a common solution, and one that will work for me. I just applied updates via the update manager and now my wired network connection is down. I know Ubuntu network settings is the issue, because I have a dual-boot with Win 7 and my network/internet is fine on Win 7. I don't know too much about networking, so what can I do to trouble shoot this issue? I can choose an older grub version, 2.6.38-8 instead of 2.6.38-11 and this does not resolve the issue. Here is my lspci result: 00:00.0 Host bridge: ATI Technologies Inc RD890 Northbridge only single slot PCI-e GFX Hydra part (rev 02) 00:02.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) 00:04.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port D) 00:05.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port E) 00:06.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port F) 00:07.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port G) 00:09.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) 00:0a.0 PCI bridge: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] (rev 40) 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 41) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:15.0 PCI bridge: ATI Technologies Inc Device 43a0 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5700 Series] 01:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 07:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 07:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 08:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) Here is my sudo lshw -class network: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 03 serial: 6c:f0:49:e7:72:e8 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:9e00(size=256) memory:fceff000-fcefffff memory:fcef8000-fcefbfff memory:fce00000-fce1ffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth1 version: 03 serial: 6c:f0:49:e7:72:ea size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:8e00(size=256) memory:fddff000-fddfffff memory:fddf8000-fddfbfff memory:fdd00000-fdd1ffff

    Read the article

  • Oracle Social Network Developer Challenge: Fishbowl Solutions

    - by Kellsey Ruppel
    Originally posted by Jake Kuramoto on The Apps Lab blog. Today, I give you the final entry in the Oracle Social Network Developer Challenge, held last week during OpenWorld. This one comes from Friend of the ‘Lab and Fishbowl Solutions (@fishbowle20) hacker, John Sim (@jrsim_uix), whom you might remember from his XBox Kinect demo at COLLABORATE 12 (presentation slides and abstract) hacks and other exploits with WebCenter. We put this challenge together specifically for developers like John, who like to experiment with new tools and push the envelope of what’s possible and build cool things, and as you can see from his entry John did just that, mashing together Google Maps and Oracle Social Network into a mobile app built with PhoneGap that uses the device’s camera and GPS to keep teams on the move in touch. He calls it a Mobile GeoTagging Solution, but I think Avengers Assemble! would have equally descriptive, given that was obviously his inspiration. Here’s his description of the mobile app: My proposed solution was to design and simplify GeoLocation mapping, and automate updates for users and teams on the move; who don’t have access to a laptop or want to take their ipads out – but allow them to make quick updates to OSN and upload photos taken from their mobile device – there and then. As part of this; the plan was to include a rules engine that could be configured by the user to allow the device to automatically update and post messages when they arrived at a set location(s). Inspiration for this came from on{x} – automate your life. Unfortunately, John didn’t make it to the conference to show off his hard work in person, but luckily, he had a colleague from Fishbowl and a video to showcase his work.    Here are some shots of John’s mobile app for your viewing pleasure: John’s thinking is sound. Geolocation is usually relegated to consumer use cases, thanks to services like foursquare, but distributed teams working on projects out in the world definitely need a way to stay in contact. Consider a construction job. Different contractors all converge on a single location, and time is money. Rather than calling or texting each other and risking a distracted driving accident, an app like John’s allows everyone on the job to see exactly where the other contractors are. Using his GPS rules, they could easily be notified about how close each is to the site, definitely useful when you have a flooring contractor sitting idle, waiting for an electrician to finish the wiring. The best part is that the project manager or general contractor could stay updated on all the action (or inaction) using Oracle Social Network, either sitting at a desk using the browser app or desktop client or on the go, using one of the native mobile apps built for Oracle Social Network. I can see this being used by insurance adjusters too, and really any team that, erm, assembles at a given spot. Of course, it’s also useful for meeting at the pub after the day’s work is done. Beyond people, this solution could also be implemented for physical objects that are in route to a destination. Say you’re a customer waiting on rail shipment or a package delivery. You could track your valuable’s whereabouts easily as they report their progress via checkins. If they deviated from the GPS rules, you’d be notified. You might even be able to get a picture into Oracle Social Network with some light hacking. Thanks to John and his colleagues at Fishbowl for participating in our challenge. We hope everyone had a good experience. Make sure to check out John’s blog post on his work and the experience using Oracle Social Network. Although this is the final, official entry we had, tomorrow, I’ll show you the work of someone who finished code, but wasn’t able to make the judging event. Stay tuned.

    Read the article

  • What could be causing this long waiting time on page load?

    - by Andrew Findlay
    What could be causing a 1.18s wait time when my page loads? Just to make sure I did not have any conflicting or parallel scripts loading, I completely deleted all the script on my home page and ran the speed test again. Although I had a blank website and 5kb file size, there was still a 900ms "waiting" time. I'm wondering if it could be my server? Any other thoughts or suggestions as it doesn't seem to be scripts. EDIT - Just ran a DNS test on pingdom and here are my results. Does this tell me anything? No nameservers found at child?

    Read the article

  • Are there well-known examples of web products that were killed by slow service?

    - by Jeremy Wadhams
    It's a basic tenet of UX design that users prefer fast pages. http://www.useit.com/alertbox/response-times.html http://www.nytimes.com/2012/03/01/technology/impatient-web-users-flee-slow-loading-sites.html?pagewanted=all It's supposedly even baked into Google's ranking algorithm now: fast sites rank higher, all else being equal. But are there well known examples of web services where the popular narrative is "it was great, but it was so slow people took their money elsewhere"? I can pretty easily think of example problems with scale (Twitter's fail whale) or reliability (Netflix and Pinterest outages caused by a single datacenter in a storm). But can (lack of) speed really kill?

    Read the article

  • http requests, using sprites and file sizes -

    - by crazy sarah
    Hi all I'm in the process of finding out all about sprites and how they can speed up your pages. So I've used spriteMe to create a overall sprite image which is 130kb, this is made up of 14 images with a combined total size of about 65kb So is it better to have one http request and a file size of 130kb or 14 requests for a total of 65kb? Also there is a detailed image which has been put into the spite which caused it's size to go up by about 60kb odd, this used to be a seperate jpg image which was only 30kb. Would I be better off having it seperate and suffering the additional request?

    Read the article

  • What's an acceptable "Avg. Page Load Time"?

    - by hawbsl
    Is there any industry rule of thumb for what's considered an unacceptable load time v. an OK one v. a blistering fast one? We're just reviewing some Google Analytics data and getting 0.74 Avg. Page Load Time reported. I guess that's OK. However it would be good if some meatier comparison data were available, or a blog post, or somewhere where there's some analysis of what speeds are generally being achieved by various kinds of sites. Any useful links to help someone interpret these speeds? If you Google it you just get a lot of results dealing with how to improve your speed. We're not at that stage yet.

    Read the article

  • How to interpret Google's "Avg. Page Load Time"?

    - by hawbsl
    Is there any industry rule of thumb for what's considered an unacceptable load time v. an OK one v. a blistering fast one? We're just reviewing some Google Analytics data and getting 0.74 Avg. Page Load Time reported. I guess that's OK. However it would be good if some meatier comparison data were available, or a blog post, or somewhere where there's some analysis of what speeds are generally being achieved by various kinds of sites. Any useful links to help someone interpret these speeds? If you Google it you just get a lot of results dealing with how to improve your speed. We're not at that stage yet.

    Read the article

  • Can't connect to Apple Time Capsule in home network using Home Plugs from Win 7 Machine

    - by Eugene
    I have the following home network setup with subnet 255.255.255.0 but recently moved my time capsule to a different location when I added a third Home Plug and can no longer ping or map a network drive to it from the Windows 7 Machine. However using Airport Utility on the Windows 7 machine I can manually configure the Time Capsule. Using a Macbook on WIFI Network 1 or 2 - I can backup to the time capsule, so its accessible via both the router wifi network and the time capsule wifi network. The Time Capsule is set to BRIDGE function - ie no NAT or DHCP server enabled. Any bright sparks out there that can help diagnose the problem? Router (192.168.1.254) WIFI Network 1 | | |---- Home Plug one |---- Home Plug Two | |---- Computer A Windows 7 (192.168.1.160) | |---- Printer (192.168.1.69) |---- Home Plug Three | |---- Apple Time Capsule (192.168.1.150) WIFI Network 2 |---- Smart TV (192.168.1.70) | |---- Apple TV (192.168.1.4)

    Read the article

  • msi netbook refuses to connect to home wireless network (windows xp)

    - by sa125
    Hi - I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

    Read the article

  • MSI netbook refuses to connect to home wireless network with Windows XP

    - by sa125
    I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

    Read the article

  • Running an executable on network share with CustomAction with wix?

    - by martin
    Hello, i have created a msi-package which compresses some xml-files to a zip-file during installation. I have created a CustomAction for this purposes: <CustomAction Id="CompressMy" BinaryKey="zipEXE" ExeCommand="a -tzip &quot;[TEMPLATE_DIR]my.zip&quot; &quot;[TempSourceFolder]data.xml&quot;" Return="check" HideTarget="no" Impersonate="no" Execute="deferred" /> The installation works fine, if i try to install to a local drive, but recently a customer wanted to install [TEMPLATE_DIR] to a network drive on Windows Vista. The CustomAction fails, because of the elevated install-user hasn't mapped the network drive, even if the installer-calling user has mapped the drive. This happens also, if I try to install to an unc-path. I use 7zip for compressing. I have added it to my msi-package. I have tried to set Impersonate="yes", but then the Installations fails, if my TEMPLATE_DIR is f.e. the ProgramData-dir. Do you have any idea what i can do? I thinked about checking if TEMPLATE_DIR is a network path, but I didn't know how i can check this. Or do you have any other Ideas how I can provide a local and a network installation while using this custom action. Would be great if there are any advices, greetings, Martin

    Read the article

  • Can a Linux system crash cause network issues?

    - by Supratik
    I have a Ubuntu box in my network which crashed, all the system connected to the switch in which the Ubuntu system was connected started giving problem. I removed that system from the network, since that was the last change I made in my network and everything was fine. So, to confirm this I again connected the system back to the network and the same network outage happened. When I checked the links it was fine. When I rebooted the problematic system and again connected back to the network switch everything started working. I think possibly the crash of the Ubuntu system could have caused this outage. Is there any possibility that a kernel crash can cause network issues?

    Read the article

  • How to set up VLAN network

    - by Paddington
    I'm changing my network from having every device on flat network to using VLans. My problem is that we already have a lot of devices on this network(192.168.20.0/24). From theory, I read that each Vlan has to be a different subnet and then I need to configure virtual interfaces on my Cisco router to cater for inter vlan routing. 1) How can I segment this network with minimum down time on the devices already on the network? 2) Can I just create Vlans and leave all these Vlans in the same layer 3 network so that they can go out of the network (I am not too concerned about inter-Vlan routing) or I have to create subnets which means reconfiguring the existing devices (something I do not want).

    Read the article

  • how to remove obsolete device and network entries? Device manager "uninstall" option has no effect

    - by Gizmo
    I am trying to remove a few "obsolete" things which annoy me (because I like to have everything cleen, working and not interferring with each other, fresh, etc..). I tried looking for solutions without any help, so here I am to ask. My first part is about removing obsolete networks, let me explain by showing the ipconfig output: C:\windows\system32>ipconfig Windows IP Configuration Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter LAN: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wi-Fi: Connection-specific DNS Suffix . : home Link-local IPv6 Address . . . . . : fe80::c129:8d57:bbd1:3564%10 IPv4 Address. . . . . . . . . . . : 192.168.2.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.254 Tunnel adapter isatap.home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : home C:\windows\system32> Specificalyy the first two adapter entries annoy me because the adapters are not visible in the network connection menu (invisible folder / file visibility set to "show"): And here is the second problem altogether with the first one: No matter what I click/do, Uninstall option has no effect on the multiplexor driver. (bridging stuff, right?) I really want to remove the Wireless LAN adapter Local Area Connection entries and the adapter multiplexor stuff but it's impossible? Why is this? How can I remove them anyway?

    Read the article

  • Network Solutions Gold VIP Program

    - by GGBlogger
    Today I received an email advising me “Congratulations! You have been selected for the Network Solutions Gold VIP Program” Now I get a bunch of messages from Network Solutions because a long time ago I chose them as my registrar. I usually just save these to my Outlook Network Solutions folder and move on. This time my wife was in the room and I chuckled and said something about “Network Solutions has made me a Gold VIP member.” She said “So what does that mean?” Prompted by that I scrolled down the page to look at my “perks". Let’s see – Special pricing, 1 year free Web Forwarding, 1 hour of free support… etc etc until I hit “Enrollment in SafeRenew* SafeRenew* simplifies your renewal process. It protects your domain name registrations and corresponding services in the event you forget or are unable to renew on time. I’m thinking “Now ain’t that neat” I don’t use auto renew anyway and never have. Then I continued reading: Beginning June 24th, 2012 your domains* (that’s 10 days away) will automatically renew. To ensure continuation of service, please be certain you have a valid credit card on file. If you do not wish for your services to be automatically renewed, please click here to log into account manager and opt out of the SafeRenew™ service. Whoa Network Solutions is going to start spending my money without so much as a by your leave sir!!! I don’t bloody think so and how truly magnanimous of them I can “click here” to opt out of what I didn’t opt in for. Talk about furious! I still am. Now the kicker is: if my wife hadn’t been curious and if I’d had a working credit card on file I wouldn’t have know this until one of my unwanted domain names auto renewed. Of course I was told “Oh – we’d have refunded your money” to which I say bull. In my view Networks Solutions is guilty of a crime of some sort. They DO NOT have a right to spend my money without asking!!!!! So watch out folks.

    Read the article

  • Fan speed monitor Software for Macbook Pro Unibody on Windows

    - by dtmunir
    I've tried multiple temperature monitor and fan speed software on my Macbook Pro Unibody under Windows 7 64-bit RC. None of them can report the fan speed. Currently I'm using SpeedFan which reports the CPU temperature of each of the two cores, but is not able to detect or interface with the Fans. Has anyone had any luck with this?

    Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >