Search Results

Search found 12774 results on 511 pages for 'memory corruption'.

Page 473/511 | < Previous Page | 469 470 471 472 473 474 475 476 477 478 479 480  | Next Page >

• CPU overheating after cleaning it

  - by Roberts

  I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

  Read the article

• How to enable caching on Apache / Ubuntu Linux?

  - by Jim Mischel

  I have a large (several megabytes) XML file that's updated rather frequently (every 10 minutes or less) and gets a lot of traffic. I'd like to implement some caching to reduce bandwidth and server load. Looking at the Apache documents, I see a dizzying array of configuration options that involve various combinations of mod_expires, mod_headers, and mod_cache (and variants). I end up running in circles and the results aren't what I expect. I'm comfortable editing the various configuration files if I have some idea what I'm supposed to change. But at the moment I'm poking around in the dark and that's never a comfortable feeling. So, perhaps if I describe what I want, somebody here can take me by the hand and say, "This is what you need to do." Periodically, this file, call it "stuff.xml" is updated and a new version copied to the directory. The external url would be, for example, http://example.com/stuff.xml. Understand, this part works. Whenever I request the file, I get the expected result. But the file is big and I want to save bandwidth, so first I'd like to implement conditional GET semantics with the If-Modified-Since header. How do I do this? I've enabled mod_headers and mod_expired and added the <FilesMatching> section in my httpd.conf as recommended in countless examples I've seen online, but that didn't change the behavior when made a conditional GET request. I always get a status 200 with the entire document. So how the heck do I implement this? That'll cut down on neeless transfers. I'd also like to limit the amount of data transferred. Seeing as this is XML, gzipping it should save me 50% or more. My next step would be to somehow gzip the file and, if it's not too difficult, store it in memory. That'll cut down on per-access data transfer, and also reduce disk transfers. So how do I implement this type of caching? Thanks in advance.

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• Ubuntu Server 12.04 CPU Load

  - by zertux

  I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

  Read the article

• What presentation software suits my needs?

  - by claws

  Background: I'm teaching biology to 12th grade students. The syllabus I'm teaching is huge. I mean literally, very huge. There is a lot for students to remember. There are no less than 1000 facts (weird names, dates etc) for students to remember. They'll have to remember all of them, they don't have a choice. The notes I compiled for their learning itself is upto 80 printed pages(Just the bullet outline & facts). That's just one chapter. We have 34 chapters. Also my students are very hardworking, they study upto 8-10hrs per day (Yeah! we are from India :). So, I want to ensure maximum retaining by the students at each and every stage (Teaching & Learning). I'm trying to as many memory training techniques as possible. I'm trying to incorporate, mnemonics, strong visual aids (pictures, 3D-animations, real videos etc.), spaced repetition etc. I think MS powerpoint is not suitable for my needs: There are about 200 slides per chapter. Its very easy for students to get lost while teaching. Because the problem with powerpoint is that it gives facts (as bullets) but it doesn't exploit the association & organization (Concept Map) of the content, which helps students learn quickly. I found an amazing software called XMind. You can see the screenshot here. Problem is that it is not as powerpoint in terms of powerpoint. This software can be used for just for concept maps. In the above screenshot, each topic occupies a single slide. I have an Image/picture(Detailed huge picture) and about 5-10 bullet points and probably a video or an animation of somethings. And this XMind is not good at presenting, in terms that it doesn't allow me to set what to present after what. I want to present a top down view, with a slide for each topic. PS: I Don't like prezi.com. I tried but it simply is too confusing for my students. It zooms here and there. I didn't tried it but I've seen few presentations.

  Read the article

• Encoding multiple video streams with a single avconv invocation

  - by automatthias

  I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

  Read the article

• How to get more information from the system crash

  - by viraptor

  I'd like to debug an issue I'm having with a linux (debian stable) server, but I'm running out of ideas of how to confirm any diagnosis. Some background: The servers are running DL160 class with hardware raid between two disks. They're running a lot of services, mostly utilising network interface and CPU. There are 8 cpus and 7 "main" most cpu-hungry processes are bound to one core each via cpu affinity. Other random background scripts are not forced anywhere. The filesystem is writing ~1.5k blocks/s the whole time (goes up above 2k/s in peak times). Normal CPU usage for those servers is ~60% on 7 cores and some minimal usage on the last (whatever's running on shells usually). What actually happens is that the "main" services start using 100% CPU at some point, mainly stuck in kernel time. After a couple of seconds, LA goes over 400 and we lose any way to connect to the box (KVM is on it's way, but not there yet). Sometimes we see a kernel reporting hung task (but not always): [118951.272884] INFO: task zsh:15911 blocked for more than 120 seconds. [118951.272955] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [118951.273037] zsh D 0000000000000000 0 15911 1 [118951.273093] ffff8101898c3c48 0000000000000046 0000000000000000 ffffffffa0155e0a [118951.273183] ffff8101a753a080 ffff81021f1c5570 ffff8101a753a308 000000051f0fd740 [118951.273274] 0000000000000246 0000000000000000 00000000ffffffbd 0000000000000001 [118951.273335] Call Trace: [118951.273424] [<ffffffffa0155e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 [118951.273510] [<ffffffff804294f6>] schedule_timeout+0x1e/0xad [118951.273563] [<ffffffff8027577c>] __pagevec_free+0x21/0x2e [118951.273613] [<ffffffff80428b0b>] wait_for_common+0xcf/0x13a [118951.273692] [<ffffffff8022c168>] default_wake_function+0x0/0xe .... This would point at raid / disk failure, however sometimes the tasks are hung on kernel's gettsc which would indicate some general weird hardware behaviour. It's also running mysql (almost read-only, 99% cache hit), which seems to spawn a lot more threads during the system problems. During the day it does ~200kq/s (selects) and ~10q/s (writes). The host is never running out of memory or swapping, no oom reports are spotted. We've got many boxes with similar/same hardware and they all seem to behave that way, but I'm not sure which part fails, so it's probably not a good idea to just grab something more powerful and hope the problem goes away. Applications themselves don't really report anything wrong when they're running. I can run anything safely on the same hardware in an isolated environment. What can I do to narrow down the problem? Where else should I look for explanation?

  Read the article

• Lag spikes at full CPU usage, maybe video card

  - by Roberts

  I am posting this thread in hurry so few things may be missed (I will update tomorrow). My PC specs: Motherboard Name - Gigabyte GA-945PL-S3 CPU Type - DualCore Intel Core 2 Duo E4300, 1800 MHz (9 x 200) OS - Microsoft Windows 7 Ultimate OS Kernel Type - 32-bit OS Version - 6.1.7601 I bougth a new video card one month ago. GeForce 210. I didn't have any problems. I wanted to overclock it, in other words: "Play with it". So I installed Gigabyte EasyBoost from CD and overclocked the GPU 590 + 110 mhz, memory to max to 960mhz from 800mhz. Benchmarks showed a little bit bigger score. Then I overclocked shader clock from 1405 to [..] (don't remeber really). So I was playing Modern Warfare 2 when off sudden computer froze when I wanted to select team, I was afk before that. I had to reset CMOS. After that I had problems with Skype: unread messages and no sound. Then I figured it out that when ever I open EasyBoost - Skype starts to glitch again. Now I use EVGA Precission X. Now after a month, I cleaned computer and closed the case, it was open all the time. I started to overclock GPU clock only (just a bit) because there was no problems that would stop me. So sometimes on heavy CPU load graphics starts to lag. Dragging a window is painful to watch too. Sometimes the screen freezes for 5 to 10 seconds (I can see that hard disk activity is maximal). You may say that CPU fault it is, isn't it? But sometimes lag spikes starts randomly when CPU load is at maximum. All 3 benchmark softwares (PerformanceTest, NovaBench and MSI Kombustor) shows that performance of my video card has dropped about 25%. BUT! CPU score is lower too. I ignored these problems but when I refreshed Windows Experience Index I was shocked. Month before (in latvian language but not so hard to understand): Now (upgraded RAM): This happened when I tried to capture Minecraft with Fraps on underclocked GPU to 580mhz (def: 590mhz): All drivers are up to date. Average CPU temperature from 55°C to 75°C (at 70°C sometimes starts these lag spikes). Video card's tempratures are from 45°C to 60°C (very hard to reach 60°C). So my hope is that the video card is fine, cause this card is very new and I want to upgrade CPU anyways. Aplogies for my mistakes in vocabulary (I am trying to type this as fast I can).

  Read the article

• Windows 7, weird/annoying explorer problem

  - by Shiki

  First of all, I'm asking the moderators if you could summarize my problem in the Title and modify it according to that. Thanks in advance and sorry, my english is not that good. The problem. It happened on two of my machines already. Once it happens there are many problems with explorer. I'll try to describe at precisely I just can. So. Basically when you create a new folder, you have to hit the enter key TWICE because first it'll throw an error that "there is no such file..". Okay. Then if you try to delete some, this happens also. Renaming is the same. Here is an example. I tried adding a "2" to the end of the folder name, hit enter and got this. Here I can press cancel, nothing happens. If I press retry, the popup disappears and it'll finally change the folder name. I can't come up with anything for this. Using BitDefender (registered, full protection), Windows 7 x86 Ultimate retail (boxed, english version). The other PC had the same anti-virus protection , but it have a Windows 7 x64. Both systems are activated, updated totally. I don't remember installing any new stuff on the PCs. All the stuff on the PCs are legal, no cracked / any other software present. It just happened, so to say. Already reinstalled the other PC because I thought * I * messed up something and its just something FUBAR. However, I dont want to reinstall my laptop also. Any ideas are welcome. (Today I had a strange bug. Windows Explorer had 1.0+gb memory usage with 100% cpu. Killed it, launched a new explorer.exe and thats all. Nothing changed, but it may worth a try. The other PC did NOT have this problem, ever.) Isn't there a registry fix for this or something? :/

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• Suspicious process running under user named

  - by Amit

  I get a lot of emails reporting this and I want this issue to auto correct itself. These process are run by my server and are a result of updates, session deletion and other legitimate session handling reported as false positives. Here's a sample report: Time: Sat Oct 20 00:00:03 2012 -0400 PID: 20077 Account: named Uptime: 326117 seconds Executable: /usr/sbin/nsd\00507d27e9\0053\00\00\00\00\00 (deleted) The file system shows this process is running an executable file that has been deleted. This typically happens when the original file has been replaced by a new file when the application is updated. To prevent this being reported again, restart the process that runs this excecutable file. See csf.conf and the PT_DELETED text for more information about the security implications of processes running deleted executable files. Command Line (often faked in exploits): /usr/sbin/nsd -c /etc/nsd/nsd.conf Network connections by the process (if any): udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 udp: 127.0.0.1:53 -> 0.0.0.0:0 udp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 tcp: 127.0.0.1:53 -> 0.0.0.0:0 tcp: xx.xx.xxx.xx:53 -> 0.0.0.0:0 Files open by the process (if any): /dev/null /dev/null /dev/null Memory maps by the process (if any): 0045e000-00479000 r-xp 00000000 fd:00 2582025 /lib/ld-2.5.so 00479000-0047a000 r--p 0001a000 fd:00 2582025 /lib/ld-2.5.so 0047a000-0047b000 rw-p 0001b000 fd:00 2582025 /lib/ld-2.5.so 0047d000-005d5000 r-xp 00000000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d5000-005d7000 r--p 00157000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d7000-005d8000 rw-p 00159000 fd:00 2582073 /lib/i686/nosegneg/libc-2.5.so 005d8000-005db000 rw-p 005d8000 00:00 0 005dd000-005e0000 r-xp 00000000 fd:00 2582087 /lib/libdl-2.5.so 005e0000-005e1000 r--p 00002000 fd:00 2582087 /lib/libdl-2.5.so 005e1000-005e2000 rw-p 00003000 fd:00 2582087 /lib/libdl-2.5.so 0062b000-0063d000 r-xp 00000000 fd:00 2582079 /lib/libz.so.1.2.3 0063d000-0063e000 rw-p 00011000 fd:00 2582079 /lib/libz.so.1.2.3 00855000-0085f000 r-xp 00000000 fd:00 2582022 /lib/libnss_files-2.5.so 0085f000-00860000 r--p 00009000 fd:00 2582022 /lib/libnss_files-2.5.so 00860000-00861000 rw-p 0000a000 fd:00 2582022 /lib/libnss_files-2.5.so 00ac0000-00bea000 r-xp 00000000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bea000-00bfe000 rw-p 00129000 fd:00 2582166 /lib/libcrypto.so.0.9.8e 00bfe000-00c01000 rw-p 00bfe000 00:00 0 00e68000-00e69000 r-xp 00e68000 00:00 0 [vdso] 08048000-08074000 r-xp 00000000 fd:00 927261 /usr/sbin/nsd 08074000-08079000 rw-p 0002b000 fd:00 927261 /usr/sbin/nsd 08079000-0808c000 rw-p 08079000 00:00 0 08a20000-08a67000 rw-p 08a20000 00:00 0 b7f8d000-b7ff2000 rw-p b7f8d000 00:00 0 b7ffd000-b7ffe000 rw-p b7ffd000 00:00 0 bfa6d000-bfa91000 rw-p bffda000 00:00 0 [stack] Would /etc/nsd/restart or kill -1 20077 solve the problem?

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• Very slow printing from print server

  - by evolvd

  Print server is a VM on Xen The VM is Windows 2003 32bit. During the issue the VM is not being taxed in anyway, cpu, memory, hd read/write, and network speed is all good. The problem that I see is the transfer of the print file from the print server to the printer. The 80Mb file is transferred from the client to the print server in about 2 minutes but then it takes about 2 hours for that file to be sent to the printer. I can't figure out why this would just start to happen. The printer is rebooted every evening and is just used for one large print job in the morning. The server has been rebooted with no effect I changed the spool option to send the entire spool to the server before printing starts and it had no effect. This printer problem did happen to come about after some changes to the Xen environment. The Xen servers changed from using HBA NIC cards to software iscsi and a new switch was put in. I don't think this is related to the problem since all the speeds on the VMs are better now. The changed happened on Saturday and the first print to this printer happened on Monday morning. I'm just putting that out there but like I said I don't think it is related but I don't want to rule it out. At this point I don't have many other options besides the physical layer. I can switch out network cable that goes to the printer and I might be able to print the same job to another printer. I wont be able to test those things out till this afternoon though. Any other ideas or test I could do to try to find the reason for the slow speed? I forgot to say that this is only happening when printing to this one printer. ===Update=== I found out that there are a few printers that currently have this issue, not just the one. There are over 30 printers on the server though so I know it's not happening to all of them. I printed a large pdf doc from the server and it was able to print at the normal speed. If the machine sends the large print request it gets to the server fine but then slow to get from the server to the printer. If sent directly from the printer it gets to the printer at the normal speed. The question now is why is there a speed difference when it comes from the machine and why would it start now?

  Read the article

• graphic error on console

  - by Christian Elsner

  I have Linux on an embedded system. There is no graphic system, but I still have graphic errors. For example, if I type: ifconfig eth2 hw ether 00:0e:8c:d0:59:d2 I see: ifconfig eth hw ether 00:0e:8:2:2 If I type Enter, it accepts the command I typed, so it's just a matter of displaying. Everything is fine, when I log in via SSH. Anyone any ideas, what could be the cause or where to look at? Output of lspci: 00:00.0 Host bridge: Intel Corporation 3100 Chipset Memory I/O Controller Hub 00:00.1 Unassigned class [ff00]: Intel Corporation 3100 DRAM Controller Error Reporting Registers 00:01.0 System peripheral: Intel Corporation 3100 Chipset Enhanced DMA Controller 00:02.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A 00:03.0 PCI bridge: Intel Corporation 3100 Chipset PCI Express Port A1 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 01) 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c9) 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 631xESB/632xESB/3100 Chipset SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 631xESB/632xESB/3100 Chipset SMBus Controller (rev 01) 02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection 03:01.0 Network controller: Siemens Nixdorf AG Device 4003 (rev 02) 03:01.1 Unassigned class [ff00]: Siemens Nixdorf AG Device 4003 (rev 02) 03:02.0 Ethernet controller: Siemens Nixdorf AG Device 4047 (rev 01) 03:03.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller 03:04.0 Unassigned class [ff00]: Siemens Nixdorf AG Device 4057 (rev 01) 04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 05:00.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 44) 06:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03) 07:00.0 VGA compatible controller: Silicon Motion, Inc. SM720 Lynx3DM (rev c1) 07:01.0 USB Controller: NEC Corporation USB (rev 43) 07:01.1 USB Controller: NEC Corporation USB (rev 43) 07:01.2 USB Controller: NEC Corporation USB 2.0 (rev 04) The whole thing is running on an Intel Core 2 Duo U2500

  Read the article

• Random Computer Crashes

  - by Josh W.

  Ok, here's a wierd one for you all. Occasionally my PC here at work will crash in a very peculiar way. My dual monitors will suddenly go blank as if there is no longer a video signal, the USB mouse light will go dark and mouse stays unresponsive, the keyboard lights will not change status when the appropriate keys are pressed (Num/Caps/Scoll Lock). The CD Tray WILL open and close. But the computer will not respond to a ping request. For all intents & purposes it's as if the computer is off, except it wasn't intentional by me. The power light and internal fans are still on and I've now lost any unsaved work. Now here's where it gets wierd. This PC is part of a batch of PC's we got from a local vendor who does our initial system builds. Mine, and 6 other co-workers PCs all have the same issue. Originally we thought it was a bad combination of hardware, but through trial and error the only thing we haven't eliminated are the OS, Mobo & CPU. The problem was so bad for some of them that they ended up going back to their 5 year old dinosaurs in order to get some work done, for me the problem isn't as bad, maybe once every other day or so, but still enough to bite me in the ass if I've forgotten my ritualistic pressing of CTRL-S every 1-5 minutes. In this case we've tried two different video cards, two different power supplies, two different memory configurations, running on a UPS/not on UPS, updating/rolling back video drivers, three different bios revisions. The only things we haven't swapped are the mobo & cpu, mainly because a new mobo means a new Hardware Abstraction Layer, ie re-install of windows and there's alot of other software on this PC that takes forever to reload by hand. There was a base image that our systems team created with all the drivers installed and the basic setup of software our company uses, but they then must customize the setup for us programmers so it takes a while to get a new configuration up and going. I'm a programmer by day and am usually pretty good at diagnosing computer problems whether through trial and error or not. We've pretty much exhausted all the ideas we can think of here, short of a new mobo/cpu. Was hoping someone out there might have anything else we can try.. Relevant Parts: OS: XP Pro 32-bit Motherboard: Intel DG41RQ CPU: Intel Core-2 Quad Q9400 @ 2.66GHz Current BIOS Version/Date Intel Corp. RQG4110H.86A.0014.2010.0306.1151, 3/6/2010 Dual LCD's, Viewsonic VG930m & Samsung SyncMaster 910v (other people have different models, but listed in case there's some very wierd problem with the signals being sent/received) PS/2 Keyboard USB Microsoft Intellimouse BIOS Versions Tried: R 0013 12/23/2009 R 0014 3/6/2010 Video cards Tried GeForce 8400 GS Radeon HD 4350 - ASUS EAH4350 Two Different Power Supplies a 380W & 550W Ram Configurations 2GB - 1 x 2GB 4GB - 2 x 2GB

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• Gigabyte GA-Z77X-D3H MB problems

  - by Hans

  I installed a new system last week. I've some issues with it. The system consists of a: Gigabyte GA-Z77X-D3H with F9 BIOS (latest) Intel Core i5 3570K proccesor Sapphire Radeon HD7850 2x 8GB Corsair 1600MHz memory OCZ Vertex 2 120G SSD Connected peripherals : 2 Samsung 940BF (1 via DVI on GFX card, 1 via an Displayport to DVI adapter) 1 Dell U2312HM monitor (displayport) Dell USB Hub (monitor) Wired mouse, wireless keyboard (logitech) Logitch G25 wheel Canon MP800 printer Okay, my issues are the following: if I plug in 1 or more monitor at DisplayPort during boot, most of the time it won't boot properly. I get an empty message screen of UEFI: only the header GIGABYTE DUEL BIOS appears. The system reboots itself, turns on for a few seconds (no video) and then reboots again. Now it starts all over again. This repeats until I remove all displayport monitors. Windows boots, and I can use them when I replug them. The graphics card has been running fine for a few weeks on an older system (intel Q6600). Another issue is; if I plug in my G25 steering wheel, the UEFI BIOS is inaccessible. It either gives the same empty UEFI screen, or the BIOS screen is rendering but crashes half way (so pieces of text and graphics are missing, and it has crashed). If I remove the G25, all is fine. To verify the graphics card is OK and the motherboard is causing these issues, I tried an NVIDIA 8800GT graphics card. This hasn't got Displayport, but it also cannot boot the BIOS with the G25 wheel plugged in. The PC also refuses to go into or out of standby. It just hangs when going into standby, and in other occasions (when it does succesfully do so) get out of standby. Power supply is OCZ StealthXStream 600W. Proccesor is 25 - 30C idle, ~55C stressed (Scythe Mugen 2). I am really puzzled what can be done to resolve this. I am not really waiting for an RMA request (otherwise I will return the MB for another type), because it will likely mean I have to wait very long before I get a replacement. Anyone else with a similar experience on this board/chipset or can help me troubleshoot this?

  Read the article

• 2xAMD Opteron 6128 with libvirt, Physical CPU 13 doesn't exist

  - by yak

  I need help with libvirt(?) problem. Server specs: ProLiant DL165 G7 2x AMD Opteron(tm) Processor 6128 System: Debian GNU/Linux testing (wheezy) 3.2.0-3-amd64 libvirt 0.9.12-5 kvm 1:1.1.2+dfsg-2 $ grep processor /proc/cpuinfo | wc -l 16 $ virsh nodeinfo setlocale: No such file or directory CPU model: x86_64 CPU(s): 16 CPU frequency: 800 MHz CPU socket(s): 2 Core(s) per socket: 4 Thread(s) per core: 1 NUMA cell(s): 1 Memory size: 66114200 KiB $ virsh capabilities .. <topology> <cells num='4'> <cell id='0'> <cpus num='4'> <cpu id='0'/> <cpu id='1'/> <cpu id='2'/> <cpu id='3'/> </cpus> </cell> <cell id='1'> <cpus num='4'> <cpu id='4'/> <cpu id='5'/> <cpu id='6'/> <cpu id='7'/> </cpus> </cell> <cell id='2'> <cpus num='4'> <cpu id='12'/> <cpu id='13'/> <cpu id='14'/> <cpu id='15'/> </cpus> </cell> <cell id='3'> <cpus num='4'> <cpu id='8'/> <cpu id='9'/> <cpu id='10'/> <cpu id='11'/> </cpus> </cell> </cells> </topology> .. $ virsh vcpupin vm 0 13,12,11,10,9,8,7,6,5 error: Physical CPU 13 doesn't exist. error: cpulist: Invalid format. Question? Why my VM Guests use only first 8 CPUs and next 8 are idling? $ for host in virsh list | awk '{print $2}'; do virsh vcpuinfo $host; done | grep ^CPU: | sort | uniq CPU: 0 CPU: 1 CPU: 2 CPU: 3 CPU: 4 CPU: 5 CPU: 6 CPU: 7 Any ideas how to change it?

  Read the article

• Routing all data through an VPN tunnel with ppp

  - by Oliver

  I'm trying to create a VPN tunnel that forwards all data from the local machine to the VPN server. I'm using ppp-2.4.5 for this with the following configuration: pty "pptp <VPNServer> --nolaunchpppd" name <my login name> remotename PPTP usepeerdns require-mppe-128 file /etc/ppp/options.pptp persist maxfail 0 holdoff 5 I have a script in if-up.d with the following content: route del default eth0 route add default dev ppp0 Before starting the VPN tunnel my routing looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 2 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 After starting the tunnel (via pon) it looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 12.34.56.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 Now the problem is, that the VPN tunnel seems to be looped into itself. If I run ifconfig after a few seconds without any traffic: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.10 netmask 255.255.0.0 broadcast 192.168.255.255 ether 00:01:2e:2f:ff:35 txqueuelen 1000 (Ethernet) RX packets 39931 bytes 6784614 (6.4 MiB) RX errors 0 dropped 90 overruns 0 frame 0 TX packets 34980 bytes 7633181 (7.2 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xfbdc0000-fbde0000 ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1496 inet 12.34.56.78 netmask 255.255.255.255 destination 12.34.56.1 ppp txqueuelen 3 (Point-to-Point Protocol) RX packets 7 bytes 94 (94.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 782863 bytes 349257986 (333.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 It states that already over 300 MiB have been send, ppp0 is only online since a few seconds and the connection isn't working anyway. Can someone please help me to fix the routing table, so that the traffic from ppp0 is not send again through ppp0 but instead goes to the remote server?

  Read the article

• SQL Server database filled the hard drive and freeing up space isn't possible

  - by Jon

  I have a database in SQL Server 2008 on a 1Tb hard drive and it filled the drive, there is only 4Kb free. The MDF file is 323Gb and the LDF is 653Gb. The hard disk this DB is on has no other files on it other than the MDF and LDF so it's impossible to free up any space on the drive. The main hard disk is smaller but there is enough room to transfer the MDF to that drive, in case that helps. This server is overseas at a customer site and it's not possible at the moment to add more disk space to the server. It's also not possible to delete any records because the DB is in a failed mode (due to no disk space) and it doesn't respond to most commands. The Db is currently in full recovery mode which is why the LDF file is so large. This DB really doesn't need to be in full recovery so going forward we plan on switching it to simple mode which will save us a lot of space. I also don't care about losing the LDF file, but I need all of the data. I've spent a lot of time looking for a way out of this problem but everything I've found first involves either freeing up disk space or adding more disk space, neither of which is an option at this time. I'm stuck and any help would be greatly appreciated. I get the following log when trying to switch the DB to online mode. Msg 945, Level 14, State 2, Line 3 Database 'DBNAME' cannot be opened due to inaccessible files or insufficient memory or disk space. See the SQL Server errorlog for details. Msg 5069, Level 16, State 1, Line 3 ALTER DATABASE statement failed. Msg 1101, Level 17, State 12, Line 3 Could not allocate a new page for database 'DBNAME' because of insufficient disk space in filegroup 'DEFAULT'. Create the necessary space by dropping objects in the filegroup, adding additional files to the filegroup, or setting autogrowth on for existing files in the filegroup. I've found the following solutions but none work due to having no disk space on that drive, and since the DB is in a failed state I can't run most commmands. - DBCC SHRINKFILE - can't be run because doing a 'use DBNAME' fails - Detaching the DB and then changing the location of the MDF/LDF files, this fails because the DB is in an offline mode so you can't run detach. I'm at a loss about what else to try. Thanks.

  Read the article

• Graphics card artifacting

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 @ stock clocks 3x 2GB DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) My graphics card started artifacting while I was playing a game. It artifacted, the display blinked, then I got an NVIDIA driver has crashed and recovered message. Kept going, more artifacts, another crash, but this time my display blanked out and I couldn't do anything. Restarted my computer - artifacting is in the BIOS - got to Windows 7 but it BSOD'd before I could even log in. I restarted the computer again - artifacts cleared themselves out and I managed to get to Win7, but it soon started blinking in and out and artifacting again. Checked the card temps and they're well within range. (50 idle, 70 full load) The ambient temperature here is about 80-85F with high humidity. Tried Safe Mode and it still froze up/BSOD'd. Already tried the following to fix this problem: - Reseat the graphics card and swapped in a different slot. - Removed cover on card and sprayed with compressed air to clean it out. - Swapped around memory and/or went with only using one stick at a time. - Underclocked card I called EVGA Tech Support and they said that the voltage on the 12V rail of my Corsair AX750 PSU was on the high end of the "acceptable" range (12.4V, highest within acceptable range is 12.6V - optimal is obviously 12V). They gave me an RMA number anyway, but I want to get a second opinion from you all before I send this thing off, as shipping from where I live to EVGA is kind of pricey. This PSU is only 6 months old. So that I don't have to play RMA tag, which case would be most likely? I'm strapped for cash at the moment so I want to reduce the amount of RMAs I have to do since shipping is expensive here. Is there any surefire way to test to see if it's really the graphics card or the PSU? I tried unplugging any devices that were connected to the 12V rail (except for my SSD and graphics card) as I do have 3 mechanical hard drives, but the voltage for that rail didn't drop (it remained at 12.4V). I'm fairly sure it isn't the drivers since I'm getting the artifacting at the BIOS too. Right now I'm back in Windows 7 but I don't know for how long until it messes up again. Any ideas?

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• amazon ec2 ubuntu with gitlab and nginx - cant load?

  - by thebluefox

  Ok, so I've spooled up an Amazon EC2 server running Ubuntu, and then followed the instructions below to install GitLab; http://doc.gitlab.com/ce/install/installation.html The only step I've not been able to complete is running the following check on the status; sudo -u git -H bundle exec rake gitlab:check RAILS_ENV=production I get the following error; rake aborted! Errno::ENOMEM: Cannot allocate memory - whoami Which I presume is becuase my EC2 is just running a free tier setup, so isn't that well spec'd. Regardless, I've been trying to access this through my browser. I've set up the elastic IP and pointed my domain at it (for the purpose of this, lets say its git.mydom.co.uk). Doing a whois on this domain shows me its pointing to the right place. For some reason though, I get the "Oops, Chrome could not connect to git.mydom.co.uk". Now - for a period of time I was getting the Nginx holding page (telling me I still needed to perform configuration). This though disappeared after removing the default file from /etc/nginx/sites-enabled/ (after reading this could be issue on a troubleshooting page). Since then, I've had nothing, even when I symlinked the file back in from /sites-available. I've tried changing the owner of the git.mydom.co.uk file sat inside /sites-enabled and /sites-available to www-data, as suggested here, but I could only change the permission of the file in /sites-available, and not the symlinked one in /sites-enabled. The content of this file is as follows; upstream gitlab { server unix:/home/git/gitlab/tmp/sockets/gitlab.socket; } server { listen *:80 default_server; # e.g., listen 192.168.1.1:80; In most cases *:80 is a good idea server_name git.mydom.co.uk; # e.g., server_name source.example.com; server_tokens off; # don't show the version number, a security best practice root /home/git/gitlab/public; # Increase this if you want to upload large attachments # Or if you want to accept large git objects over http client_max_body_size 20m; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } All the paths mentioned in here look ok...I'm about at the end of my knowledge now!

  Read the article

• Add Machine Key to machine.config in Load Balancing environment to multiple versions of .net framework

  - by davidb

  I have two web servers behind a F5 load balancer. Each web server has identical applications to the other. There was no issue until the config of the load balancer changed from source address persistence to least connections. Now in some applications I receieve this error Server Error in '/' Application. Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Web.HttpException: Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. Source Error: The source code that generated this unhandled exception can only be shown when compiled in debug mode. To enable this, please follow one of the below steps, then request the URL: Add a "Debug=true" directive at the top of the file that generated the error. Example: or: 2) Add the following section to the configuration file of your application: Note that this second technique will cause all files within a given application to be compiled in debug mode. The first technique will cause only that particular file to be compiled in debug mode. Important: Running applications in debug mode does incur a memory/performance overhead. You should make sure that an application has debugging disabled before deploying into production scenario. How do I add a machine key to the machine.config file? Do I do it at server level in IIS or at website/application level for each site? Does the validation and decryption keys have to be the same across both web servers or are they different? Should they be different for each machine.config version of .net? I cannot find any documentation of this scenario.

  Read the article

< Previous Page | 469 470 471 472 473 474 475 476 477 478 479 480  | Next Page >